is now part of .... UB62010-0SS11 X-BAND BLOCK UP CONVERTER General Information: Features: The UB62010-0SS11 X-Band Block Up 7.900 to 8.400 GHz Coverage Converter was designed for use in commercial Lightweight: less than 1 pound and military miniature SATCOM systems. Planar Package Intended for convenient systems integration, MIL-STD-188-168A Phase Noise the compact unit can be mounted for Internal Image Filtering maximum efficiency of operation in a customer Integral Monitor and Alarm supplied package. User Adjustable Gain This item is subject to International Traffic in Arms Regulations (ITAR) and is classified as 22 CFR, Part 121, Category XI (a)(5) per United States Munitions List (USML). Compliance with the Department of State ITAR is required for export of this item. 11642DS Rev A Americas (Head Office) CPI Satcom Products Palo Alto, CA USA T: +1 (650) 846-3803 F: +1 (650) 424-1744 Europe, Middle East & Africa CPI International Inc. Cham, Switzerland T: +41 (41) 560 7550 F: +41 (41) 560 7551 CPI Europe, Limited Surrey, England T: +44 (1932) 256 930 F: +44 (1932) 241 271 Asia Pacific CPI Asia, Inc. Singapore T: +65 6225 0011 F: +65 9620 5200 www.cpii.com [email protected] X-Band Block Up Converter Electrical Characteristics Parameter Range Input Frequency Range 950.-1450. MHz Output Frequency Range 7.900-8.400 GHz Local Oscillator Comments 6.950 GHz External Reference Frequency 10.000 000 MHz 0 dBm ±5 dB Phase Noise (SSB) 100 Hz -75 dBc/Hz 1 kHz -80 dBc/Hz 10 kHz -85 dBc/Hz 100 kHz -100 dBc/Hz 1 MHz -110 dBc/Hz Linear Gain Reference multiplexed on IF input 15dB (min) Gain Flatness ±0.75dB (max) per full band Gain Slope ±0.40dB (max) per 40 MHz Gain Stability vs temperature ±1.5 dB (max) User Gain Adjustment Range 31.5 dB in 0.5 dB steps P1dB +10 dBm (min) PLINEAR +8 dBm (min) Third Order Intermodulation Distortion -25 dBc max. Via Serial Interface 2 equal in-band signals, 5 MHz spacing each 6 dB below rated P1dB Noise Figure 12 dB (typ) Input VSWR 1.70 (typ), 2.00 (max) Output VSWR 1.25 (typ), 1.40 (max) Output Isolator Included Input Overdrive +0 dBm (max) non-damaging Spurious, Signal Related (@ rated P1dB) -60 dBc (max) within output band -60 dBm (max) outside of band Temp., Gain Adj., Lock Status, SSPA Control RS-232/RS-485 Serial I/O Spurious, Signal Independent (@ rated P1dB) M&C Function Power Requirement +12 vdc ±5% at .75A (max) Mechanical Specifications Size (see outline drawing 11598) 4.65 x 3.50 x 1.17 in. Weight 1.0 lbs (nom) Finish Passivated aluminum LxWxH Connectors IF / External Reference Input + 12 vdc input, M&C I/0 RF Output Type SMA (f) 10 MHz Reference Multiplexed on IF DB15 Type SMA (f) Environmental Operating Temperature Range Humidity -40° to +74°C 100% 11642DS Rev A www.cpii.com [email protected] Specifications are subject to change. Non-condensing