M16C/6S Group REJ03B0014-0501 Rev.5.01 Dec 10, 2009 SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Overview The M16C/6S group are highly integrated single-chip microcomputers with PLC (Power Line Communication) modem core and AFE (Analog Front End) in a 64-pin plastic molded LQFP package, which incorporates IT800 PLC modem technology developed by Yitran Communications Ltd. M16C/60 Series CPU core enables a high level of code efficiency and high-speed operation. In addition, the implementation of Yitran's patented DCSK (Differential Code Shift Keying) spread spectrum modulation technique in the IT800 modem core enables extremely robust communication over the existing electrical wiring, with data rates up to 7.5Kbps. The M16C/6S complies with worldwide regulations (FCC part 15, ARIB and CENELEC bands) and is suitable for a variety of narrowband applications like smart metering and home networking. Applications Power Line Communication ------Table of Contents-----Overview ......................................................... 1 Memory ......................................................... 10 Central Processing Unit (CPU) ..................... 11 SFR ............................................................... 13 Reset ............................................................. 19 Processor Mode ............................................ 23 Clock Generation Circuit ............................... 27 Protection ...................................................... 46 Interrupts ....................................................... 47 Watchdog Timer ............................................ 66 DMAC ........................................................... 68 Timers ........................................................... 78 Timer A ...................................................... 79 Serial I/O ....................................................... 92 Clock Synchronous serial I/O Mode ........ 101 UART Mode ............................................. 109 Special Mode ........................................... 117 SI/O3 and SI/O4 ...................................... 132 Programmable I/O Ports ............................. 137 Electrical Characteristics ............................. 149 Flash Memory Version ................................ 160 IT800AFE (Analog Front End) .................... 184 Usage Notes ............................................... 189 Appendix ..................................................... 199 Specifications written in this manual are believed to be accurate, but are not guaranteed to be entirely free of error. Specifications in this manual may be changed for functional or performance improvements. Please make sure your manual is the latest edition. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 1 of 201 M16C/6S Group Overview Performance Outline Table 1.1.1 lists performance outline of M16C/6S group. Table 1.1.1. Performance outline of M16C/6S group CPU Item Number of basic instructions Minimum Instruction Execution time Operation Mode Memory Space Memory Capacity ROM RAM Port Multifunction Timer Serial I/O Performance 91 instructions 65.1 ns (f(BCLK)= 15.36MHZ, VCC= 3.0V to 3.6V) Single-chip mode 1M Byte See Tables 1.1.3 and 1.1.4 Product List 24K Byte Peripheral Input/Output : 21 pins, Input : 1 pin Function Timer A : 16 bits x 5 channels, 2 channels Clock synchronous, UART, I2C bus(1), 1 channel UART, I2C bus(1), 2 channels Clock synchronous(*) (*) 1 channel is internally connected to IT800 DMAC 2 channels Watchdog Timer 15 bits x 1 channel (with prescaler) Interrupt 21 internal and 3 external sources, 4 software sources, 7 levels Clock Generation Circuit 2 circuits Main clock generation circuit with PLL synthesizer (*), On-chip oscillator, (*) This circuit contains a built-in feedback resister. Electrical Power supply voltage 3.0V to 3.6V Characteristics Power Consumption 70mA (VCC= VCCA= 3.3V, f(XIN)= 5.12MHz) Flash memory Program/Erase Supply Voltage 3.0V to 3.6V (Topr= 0 to 60°C) Version Program and Erase Endurance 100 times or 1,000 times (2) Power consumption 70mA (VCC= VCCA= 3.3V, f(XIN)= 5.12MHz) Operating Ambient Temperature (2) -20 to 85°C -40 to 85°C -40 to 105°C Package 64-pin plastic mold LQFP Notes: 1. I2C Bus is a registered trademark of Koninklijke Philips Electronics N. V. 2. See Tables 1.1.5 and 1.1.6 Product code for increased program/erase cycle version, and version of expanded operating ambient temperature. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 2 of 201 Overview M16C/6S Group IT800 PHY performance outline of M16C/6S group. The IT800 PHY is a PLC optimized Physical Layer (PHY) which consists of IT800 modem core and internal AFE (Analog Front End). The implementation of Yitran's patented DCSK spread spectrum modulation technique in the IT800 modem core enables extremely robust communication over the existing electrical wiring, with data rates up to 7.5Kbps. In addition to the inherent interference immunity provided by the DCSK modulation, the IT800 PHY utilizes several mechanisms for enhanced communication robustness, such as forward short block soft decoding error correction algorithm and special synchronization algorithms. The IT800PHY communicates M16C core with clock synchronous serial I/O, interrupt and input/output ports in M16C/6S (Note). M16C/6S requires external AFE. Table 1.1.2 lists IT800 PHY performance outline of M16C/6S group. Table 1.1.2. IT800 PHY performance outline of M16C/6S group Item Performance Features High immunity to signal fading, various noise characteristics, impedance modulation and phase/frequency distortion High in-phase and cross-phase reliability Modulation Technique DCSK (Differential Code Shift Keying)* *Yitran patented modulation technique Error Correction/Detection Forward short-block soft decoding error correction mechanism, CRC-16 Complies with W/W Regulations FCC, ARIB, EN50065-1-CENELEC Data Rate & FCC & ARIB 120-400 KHz Frequency Band 7.5Kbps Standard Mode (SM) 5.0Kbps Robust Mode (RM) 1.25Kbps Extremely Robust Mode (ERM) CENELEC A-Band (Outdoor): 20-80 KHz B-Band (Indoor): 95-125 KHz 2.5 Kbps Robust Mode (RM) 0.625Kbps Extremely Robust Mode (ERM) Internal AFE 10bit-D/A converter, preamp, 1bit-A/D converter x 3 channels Note: Direct operation of IT800 PHY is not recommended. Since the Layer 2 (DLL) handles the channel access procedure, using the IT800DLL as such assures coexistence with other IT800 technology based products, regardless of the vendor, protocol and the application. There is NO such coexistence if the device is used in direct operation of IT800 PHY. Note that the coexistence here is not with other technologies but with other IT800 technology based products. As for details, please refer to the next section and Appendix. About Firmware Renesas recommends IT800DLL (Product name: D2DL) as a Data Link Layer (DLL) of M16C/6S group. The IT800 DLL is a PLC optimized DLL especially for the products based on Yitran's IT800 technology. For availability of IT800DLL, please contact Renesas technical support representative. For more details about the IT800DLL advantages, please refer to Appendix. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 3 of 201 1 XOUT 5.12MHz XIN M16C Core A0 FB SB R0L R1L nCD1 nCD0 P56 P54 P53 RAM SI1 SI3 CLK_IN 46.08MHz SI2 EXTCLK 15.36MHz nINT nPHY_RES P42 P82/INT0 TXnRX CLR P40 DI DO P97/SIN4 DCLK TEST_C SO TS IT800 Modem Core P96/SOUT4 P95/CLK4 Inner Ports P10 P41 P11 System clock generator PLL module ROM Memory DMA C (2channels) Timer (16bits) Output (TimerA) 5 Watchdog timer (15bits) UART or Clock synchronous serial I/O (8bits ✕3channels) Clock synchronous serial I/O (8bits ✕2channels) FLG Flag register USP ISP Stack Pointer R0H R1H Internal Peripherals Multiplier INTB Vector table PC Program Counter R2 R3 A1 M16C/60 series 16-bit CPU core register 8 5 5 Port P1 Port P6 Port P7 Port P8 page 4 of 201 Port P85 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 3 Figure 1.1.1. Block Diagram of Chip and PLC application Outline Port P9 Block Diagram of Chip 10 10bit D/A OPAMP Comparator Comparator Comparator 1bit-A/D x 3 Preamplifier TEST_A OPAMP OPAMP OPAMP BUFFER Internal AFE Buffer Buffer CH3_INN FB3 AMP3_IN CH3_INP AMP3_OUT CH2_INN FB2 VREF AMP2_IN CH2_INP AMP2_OUT FB1 CH1_INN AMP1_IN CH1_INP AMP1_OUT VccA VssA PRE_BOUT VREF PRE_INN PRE_INP IOUTC Rext IOUT TS Line driver 300 to 400KHz BPF 200 to 300KHz BPF 100 to 200KHz BPF Filters Line coupling M16C/6S Group Overview Block Diagram and PLC application Outline Figure 1.1.1 is a block diagram of the M16C/6S group and PLC application Outline. M16C/6S Group Overview Product List Tables 1.1.3 and 1.1.4 list the M16C/6S group product and Figure 1.1.2 shows the type numbers, memory sizes and packages. Table 1.1.3. Product List (1) M16C/6S Type No. M306S0FAGP ROM capacity RAM capacity 96K bytes 24K bytes Current of Dec. 2009 Package type Remarks PLQP0064KB-A (64P6Q-A) Flash memory Product Code U3, U5, U7(D), U9(D) (D): under development Table 1.1.4. Product List (2) M16C/6S D-version Current of Dec. 2009 ROM capacity RAM capacity M306S0F8DGP 64K bytes 24K bytes PLQP0064KB-A (64P6Q-A) Flash memory U3 M306S0FADGP 96K bytes 24K bytes PLQP0064KB-A (64P6Q-A) Flash memory U3 Type No. Type No. Package type Remarks Product Code M 3 0 6 S 0 F A D G P – U3 Product code See Tables 1.1.5 and 1.1.6 Product code Package type: GP : Package 64P6Q-A Version (no) : M16C/6S D : M16C/6S D-version ROM capacity: 8: 64K bytes A: 96K bytes Memory type: F: Flash memory version Shows RAM capacity, pin count, etc (The value itself has no specific meaning) M16C/6S Group M16C Family Figure 1.1.2. Type No., Memory Size, and Package Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 5 of 201 M16C/6S Group Overview Table 1.1.5. Product Code (1) M16C/6S Internal ROM Product Code Package E/W cycles U3 U5 LEAD free U7 (D) U9 (D) (D): under development Temperature range 100 0°C to 60°C 1,000 Table 1.1.6. Product Code (2) M16C/6S D-version Internal ROM Product Package Temperature Code E/W cycles range U3 LEAD free 100 0°C to 60°C Microcomputer operating temperature -40°C to 85°C -20°C to 85°C -40°C to 85°C -20°C to 85°C Microcomputer operating temperature -40°C to 105°C (1) M16C/6S XXXXXXX 306S0FA U3 YITRAN IT800 Date Code (7 digits) indicates manufacturing management code Product Name and Product Code 306S0FA indicates M306S0FAGP U3 indicates product code U5 has no product code marking This indicates using Yitran's IT800 technology (2) M16C/6S D-version XXXXXXX M306S0FADGP Date Code (7 digits) indicates manufacturing management code Product Name M306S0FADGP indicates M306S0FADGP U3 YITRAN IT800 This indicates using Yitran's IT800 technology Figure 1.1.3. Marking (Top View) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 6 of 201 M16C/6S Group Overview Pin Configuration Figures 1.1.4 show the pin configurations (top view). VCCA PRE_INP PRE_INN PRE_BOUT VCC25 XOUT XIN IFLT VSS P85 P84/INT2 P76/TA3OUT P81/TA4IN P74/TA2OUT P83/INT1 P62/RXD0/SCL0 PIN CONFIGURATION (top view) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 CNVSS VSSA VREF VDCCN AMP1_IN AMP1_OUT AMP2_OUT AMP2_IN AMP3_IN AMP3_OUT CH3_INP CH3_INN FB3 CH2_INP CH2_INN FB2 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 M16C/6S YITRAN IT800 P63/TXD0/SDA0 TS P61/CLK0 P73/CTS2/RTS2/TA1IN P60/CTS0/RTS0 P66/RXD1/SCL1 P90/CLK3 P64/CTS1/RTS1/CLKS1 P91/SIN3 P67/TXD1/SDA1 P92/SOUT3 P65/CLK1 RESET P70/TXD2/SDA2/TA0OUT(Note) P71/RXD2/SCL2/TA0IN VSS CH1_INP CH1_INN FB1 VCCA VSSA IOUTC IOUT REXT GND/TST VCC25 VCC NC3 NC2 NC1 P15/INT3 P80/TA4OUT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Package: PLQP0064KB-A (64P6Q-A) Note: P70 is N channel open-drain output pins. Figure 1.1.4. Pin Configuration (Top View) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 7 of 201 M16C/6S Group Overview Table 1.1.7 Pin Description (1) Pin name VCC, VSS Signal name Power supply input I/O type CNVSS CNVSS Input RESET XIN Reset input Clock input Input Input XOUT Clock output Output VCCA Function Apply 3.0V to 3.6V to the VCC pin. Apply 0V to the VSS pin. This is a pin for changing flash memory mode. Usually, connect to VSS. “L” on this input resets the microcomputer. I/O pins for the main clock generation circuit. Connect a ceramic resonator or crystal oscillator between XIN and XOUT (3). To use the external clock, input the clock from XIN and leave XOUT open. This pin is a power supply input of analog circuit. Connect to VCC. Analog power supply input VSSA Analog power This pin is a power supply input of analog circuit. Connect to VSS. supply input GND/TST Input for test Input This is input pin for test. Connect to VSS. P15 Input/output This is an 1-bit I/O port equivalent to P6. By choosing by the program, I/O port P1 it functions as an input pin of INT interrupt. VCC25 Power supply It is the 2.5V power supply pin which is carrying out internal generating. Connect VCC25 two pins each other and add stabilization capacity. Input/output This is the 8-bit I/O port of CMOS. It has a direction register for choosing I/O, and is P60 to P67 I/O port P6 made for every pin in an input port or an output port. An input port can choose the existence of pull-up resistance in a 4-bit unit by the program. It functions as an I/O pin of what is chosen by the program which are therefore UART0 and UART1. I/O port P7 Input/output It is an I/O port with a function equivalent to P6 (however, P70 N channel open-drain P70, P71, output). By choosing by the program, it functions as an I/O pin of timers A0 to A3. P73, P74, Moreover, P70 to P73 function also as an I/O pin of UART2. P76 P80, P81, I/O port P8 Input/output P80, P81, P83, and P84 are I/O ports with a function equivalent to P6. By choosing by the program, P80 to P81 function as an I/O pin of timer A4, P83, P84, and P83 to P84 functions as an input pin of INT interruption. P85 P85 cannot be used as general input pin. Pull-up resistance cannot set up this pin. Input Input port This pin must be pulled-up externally to Vcc, and be fixed to “H”. P85 Input/output It is an I/O port with a function equivalent to P6. It functions as an I/O pin of SILO3 by choosing by the program. Output port Output This is the pin with which IT800 controls ON/OFF of an output to the external TS transmission AMP at the time of power line communication. Inner port P10 keep Input Port for IT800 Testing. Please set Direction Register PD1_0 “0” for keeping Input. Inner port P11 keep Input Port for AFE Testing. Please set Direction Register PD1_1 “0” for keeping Input. Output to Inner port I/O Port for communication between M16C Core and IT800 Modem. Please set IT800 P40 Direction Register PD4_0 “1” to Output a signal to IT800. The output signal is connected to TXnRX of IT800 inside of chip. Input from I/O Port for communication between M16C Core and IT800 Modem (Note.1). Inner port IT800 P41 Please set Direction Register PD4_1 “0” to Input a signal from IT800. The TS signal is input from IT800 inside of chip. Output to Inner port I/O Port for communication between M16C Core and IT800 Modem. Please set IT800 P42 Direction Register PD4_2 “1” to Output a signal to IT800. The output signal is connected to CLR of IT800 inside of chip. Input from I/O Port for communication between M16C Core and IT800 Modem (Note.1). Inner port IT800 P53 Please set Direction Register PD5_3 “0” to Input a signal from IT800. The nCD0 signal is input from IT800 inside of chip. Input from I/O Port for communication between M16C Core and IT800 Modem (Note.1). Inner port IT800 P54 Please set Direction Register PD5_4 “0” to Input a signal from IT800. The nCD1 signal is input from IT800 inside of chip. Output to Inner port I/O Port for communication between M16C Core and IT800 Modem. Please set IT800 P56 Direction Register PD5_6 “1” to Output a signal to IT800. The output signal is connected to nPHY_RES of IT800 inside of chip. Input from I/O Port for communication between M16C Core and IT800 Modem (Note.1). Inner port IT800 P82 nINT signal of IT800 is connected to this port inside of chip for carrying out Interrupt function by software. Output to Inner port I/O Port for communication between M16C Core and IT800 Modem. This port is IT800 P95 connected to DCLK signal of IT800 inside of chip as SILO4 CLK4 functional Output port by choosing by the program. Output to Inner port I/O Port for communication between M16C Core and IT800 Modem. This port is IT800 P96 connected to DI signal of IT800 inside of chip as SILO4 SOUT4 functional Output port by choosing by the program. Input from I/O Port for communication between M16C Core and IT800 Modem. This port is Inner port IT800 P97 connected to DI signal of IT800 inside of chip as SILO4 SOUT4 functional Input port by choosing by the program. P90 to P92 I/O port P9 TS P10 P11 P40 P41 P42 P53 P54 P56 P82 P95 P96 P97 NOTES: 1. In case of Direction Register “1”, any signal is not output from M16C to assigned signal of IT800 . Refer to Programmable I/O Ports pages. 2. Ask the oscillator maker the oscillation characteristic. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 8 of 201 M16C/6S Group Overview Table 1.1.8 Pin Description (2) (Analog pin) Pin name Function I/O type PRE-BOUT Output This is a pre-amp buffer output. PRE-INN Input This is a pre-amp differential signal input. PRE-INP Input This is a pre-amp differential signal input. VREF Input This is the reference voltage input of amplifier common to channels 1, 2, and 3. VDCCN Input This is a pin for a test. Usually, please carry out a pull-up. AMP1-IN Input This is a channel 1 amplifier input. AMP1-OUT Output This is a channel 1 amplifier output. AMP2-IN Input This is a channel 2 amplifier input. AMP2-OUT Output This is a channel 2 amplifier output. AMP3-IN Input This is a channel 3 amplifier input. AMP3-OUT Output This is a channel 3 amplifier output. CHI-INP Input This is a channel 1 comparator differential input. CHI-INN Input This is a channel 1 comparator differential input. FB1 Output This is a channel 1 comparator feedback output. CH2-INP Input This is a channel 2 comparator differential input. CH2-INN Input This is a channel 2 comparator differential input. FB2 Output This is a channel 2 comparator feedback output. CH3-INP Input This is a channel 3 comparator differential input. CH3-INN Input This is a channel 3 comparator differential input. FB3 Output This is a channel 3 comparator feedback output. IOUTC Output This is the differential current output of DAC. IOUT Output This is the differential current output of DAC. REXT Input This is for external reference resistor of DAC. IFLT Input This is the pin for low path filters of PLL. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 9 of 201 M16C/6S Group Memory Memory Figure 1.2.1 is a memory map of the M16C/6S group. The address space extends the 1M bytes from address 0000016 to FFFFF16. The internal ROM is allocated in a lower address direction beginning with address FFFFF16. For example, a 96-Kbyte internal ROM is allocated to the addresses from E800016 to FFFFF16. The fixed interrupt vector table is allocated to the addresses from FFFDC16 to FFFFF16. Therefore, store the start address of each interrupt routine here. The internal RAM is allocated in an upper address direction beginning with address 0040016. For example, a 24-Kbytes internal RAM is allocated to the addresses from 0040016 to 063FF16. In addition to storing data, the internal RAM also stores the stack used when calling subroutines and when interrupts are generated. The SRF is allocated to the addresses from 0000016 to 003FF16. Peripheral function control registers are located here. Of the SFR, any area which has no functions allocated is reserved for future use and cannot be used by users. The special page vector table is allocated to the addresses from FFE0016 to FFFDB16. This vector is used by the JMPS or JSRS instruction. For details, refer to the “M16C/60 and M16C/20 Series Software Manual.” 0000016 SFR FFE0016 0040016 Internal RAM Special page vector table XXXXX16 Internal ROM Internal RAM Size Address XXXXX16 24K bytes 063FF16 Size Address YYYYY16 64K bytes F000016 96K bytes E800016 Can not Use FFFDC16 Undefined instruction FFFFF16 BRK instruction Address match Single step Watchdog timer DBC Reserved Reset Overflow YYYYY16 Internal ROM FFFFF16 Note 1: Shown here is a memory map for the case where the PM13 bit in the PM1 register is “1”. Figure 1.2.1. Memory Map Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 10 of 201 M16C/6S Group Central Processing Unit (CPU) Central Processing Unit (CPU) Figure 1.3.1 shows the CPU registers. The CPU has 13 registers. Of these, R0, R1, R2, R3, A0, A1 and FB comprise a register bank. There are two register banks. b31 b15 b8 b7 b0 R2 R0H(R0's high bits) R0L(R0's low bits) R3 R1H(R1's high bits)R1L(R1's low bits) R2 Data registers (Note) R3 A0 b19 A1 Address registers (Note) FB Frame base registers (Note) b15 b0 INTBH INTBL Interrupt table register The upper 4 bits of INTB are INTBH and the lower 16 bits of INTB are INTBL. b19 b0 PC Program counter b15 b0 USP User stack pointer ISP Interrupt stack pointer SB Static base register b15 b0 FLG b15 b8 IPL b7 Flag register b0 U I O B S Z D C Carry flag Debug flag Zero flag Sign flag Register bank select flag Overflow flag Interrupt enable flag Stack pointer select flag Reserved area Processor interrupt priority level Reserved area Note: These registers comprise a register bank. There are two register banks. Figure 1.3.1. Central Processing Unit Register (1) Data Registers (R0, R1, R2 and R3) The R0 register consists of 16 bits, and is used mainly for transfers and arithmetic/logic operations. R1 to R3 are the same as R0. The R0 register can be separated between high (R0H) and low (R0L) for use as two 8-bit data registers. R1H and R1L are the same as R0H and R0L. Conversely, R2 and R0 can be combined for use as a 32bit data register (R2R0). R3R1 is the same as R2R0. (2) Address Registers (A0 and A1) The register A0 consists of 16 bits, and is used for address register indirect addressing and address register relative addressing. They also are used for transfers and logic/logic operations. A1 is the same as A0. In some instructions, registers A1 and A0 can be combined for use as a 32-bit address register (A1A0). Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 11 of 201 M16C/6S Group Central Processing Unit (CPU) (3) Frame Base Register (FB) FB is configured with 16 bits, and is used for FB relative addressing. (4) Interrupt Table Register (INTB) INTB is configured with 20 bits, indicating the start address of an interrupt vector table. (5) Program Counter (PC) PC is configured with 20 bits, indicating the address of an instruction to be executed. (6) User Stack Pointer (USP) and Interrupt Stack Pointer (ISP) Stack pointer (SP) comes in two types: USP and ISP, each configured with 16 bits. Your desired type of stack pointer (USP or ISP) can be selected by the U flag of FLG. (7) Static Base Register (SB) SB is configured with 16 bits, and is used for SB relative addressing. (8) Flag Register (FLG) FLG consists of 11 bits, indicating the CPU status. • Carry Flag (C Flag) This flag retains a carry, borrow, or shift-out bit that has occurred in the arithmetic/logic unit. • Debug Flag (D Flag) The D flag is used exclusively for debugging purpose. During normal use, it must be set to “0”. • Zero Flag (Z Flag) This flag is set to “1” when an arithmetic operation resulted in 0; otherwise, it is “0”. • Sign Flag (S Flag) This flag is set to “1” when an arithmetic operation resulted in a negative value; otherwise, it is “0”. • Register Bank Select Flag (B Flag) Register bank 0 is selected when this flag is “0” ; register bank 1 is selected when this flag is “1”. • Overflow Flag (O Flag) This flag is set to “1” when the operation resulted in an overflow; otherwise, it is “0”. • Interrupt Enable Flag (I Flag) This flag enables a maskable interrupt. Maskable interrupts are disabled when the I flag is “0”, and are enabled when the I flag is “1”. The I flag is cleared to “0” when the interrupt request is accepted. • Stack Pointer Select Flag (U Flag) ISP is selected when the U flag is “0”; USP is selected when the U flag is “1”. The U flag is cleared to “0” when a hardware interrupt request is accepted or an INT instruction for software interrupt Nos. 0 to 31 is executed. • Processor Interrupt Priority Level (IPL) IPL is configured with three bits, for specification of up to eight processor interrupt priority levels from level 0 to level 7. If a requested interrupt has priority greater than IPL, the interrupt is enabled. • Reserved Area When write to this bit, write "0". When read, its content is indeterminate. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 12 of 201 M16C/6S Group SFR SFR Register Address Symbol After reset 000016 000116 000216 000316 000416 000516 000616 000716 Processor mode register 0 Processor mode register 1 System clock control register 0 System clock control register 1 (Note 2) PM0 PM1 CM0 CM1 XXXX0X002 (CNVSS pin is “L”) 00XX10X02 010010002 001000002 000816 AIER PRCR XXXXXX002 XX0000002 CM2 0000X0002 Watchdog timer start register Watchdog timer control register Address match interrupt register 0 WDTS WDC RMAD0 ??16 00??????2 0016 0016 X016 Address match interrupt register 1 RMAD1 0016 0016 X016 001E16 Processor mode register 2 PM2 XXX000002 001F16 002016 DMA0 source pointer SAR0 ??16 ??16 X?16 DMA0 destination pointer DAR0 ??16 ??16 X?16 DMA0 transfer counter TCR0 ??16 ??16 DMA0 control register DM0CON 00000?002 DMA1 source pointer SAR1 ??16 ??16 X?16 DMA1 destination pointer DAR1 ??16 ??16 X?16 DMA1 transfer counter TCR1 ??16 ??16 DMA1 control register DM1CON 00000?002 000916 000A16 Address match interrupt enable register Protect register 000B16 000C16 Oscillation stop detection register (Note 3) 000D16 000E16 000F16 001016 0011 16 001216 001316 001416 001516 001616 001716 001816 001916 001A16 001B16 001C16 001D16 002116 002216 002316 002416 002516 002616 002716 002816 002916 002A16 002B16 002C16 002D16 002E16 002F16 003016 003116 003216 003316 003416 003516 003616 003716 003816 003916 003A16 003B16 003C16 003D16 003E16 003F16 Note 1: The blank areas are reserved and cannot be used by users. Note 2: The PM00 and PM01 bits do not change at software reset, watchdog timer reset and oscillation stop detection reset. Note 3: The CM20, CM21, and CM27 bits do not change at oscillation stop detection reset. X : Nothing is mapped to this bit ? : Undefined Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 13 of 201 M16C/6S Group SFR Register Symbol After reset INT3 interrupt control register INT3IC XX00?0002 UART1 BUS collision detection interrupt control register UART0 BUS collision detection interrupt control register SI/O4 interrupt control register (S4IC) SI/O3 interrupt control register UART2 Bus collision detection interrupt control register DMA0 interrupt control register DMA1 interrupt control register U1BCNIC U0BCNIC S4IC S3IC BCNIC DM0IC DM1IC XXXX?0002 XXXX?0002 XX00?0002 XX00?0002 XXXX?0002 XXXX?0002 XXXX?0002 UART2 transmit interrupt control register UART2 receive interrupt control register UART0 transmit interrupt control register UART0 receive interrupt control register UART1 transmit interrupt control register UART1 receive interrupt control register Timer A0 interrupt control register Timer A1 interrupt control register Timer A2 interrupt control register Timer A3 interrupt control register Timer A4 interrupt control register S2TIC S2RIC S0TIC S0RIC S1TIC S1RIC TA0IC TA1IC TA2IC TA3IC TA4IC XXXX?0002 XXXX?0002 XXXX?0002 XXXX?0002 XXXX?0002 XXXX?0002 XXXX?0002 XXXX?0002 XXXX?0002 XXXX?0002 XXXX?0002 INT0 interrupt control register INT1 interrupt control register INT2 interrupt control register INT0IC INT1IC INT2IC XX00?0002 XX00?0002 XX00?0002 Address 004016 004116 004216 004316 004416 004516 004616 004716 004816 004916 004A16 004B16 004C16 004D16 004E16 004F16 005016 005116 005216 005316 005416 005516 005616 005716 005816 005916 005A16 005B16 005C16 005D16 005E16 005F16 006016 006116 006216 006316 006416 006516 006616 006716 006816 006916 006A16 006B16 006C16 006D16 006E16 006F16 007016 007116 007216 007316 007416 007516 007616 007716 007816 007916 007A16 007B16 007C16 007D16 007E16 007F16 Note :The blank areas are reserved and cannot be used by users. X : Nothing is mapped to this bit ? : Undefined Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 14 of 201 M16C/6S Group SFR Register Address Symbol After reset 008016 008116 008216 008316 008416 008516 008616 ~ ~ 01B016 01B116 01B216 01B316 01B416 01B516 Flash memory control register 1 (Note 2) FMR1 0?00??0?2 Flash memory control register 0 Address match interrupt register 2 (Note 2) FMR0 RMAD2 ??0000012 0016 0016 X016 XXXXXX002 0016 0016 X016 01B616 01B716 01B816 01B916 01BA16 01BB16 Address match interrupt enable register 2 01BC16 Address match interrupt register 3 AIER2 RMAD3 01BD16 01BE16 01BF16 ~ ~ 025016 025116 025216 025316 025416 025516 025616 025716 025816 025916 025A16 025B16 025C16 025D16 025E16 Peripheral clock select register PCLKR 00000011 2 025F16 ~ ~ 033016 033116 033216 033316 033416 033516 033616 033716 033816 033916 033A16 033B16 033C16 033D16 033E16 033F16 Note 1: The blank areas are reserved and cannot be used by users. Note 2: This register is included in the flash memory version. X : Nothing is mapped to this bit ? : Undefined Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 15 of 201 M16C/6S Group SFR Address Register Symbol After reset 034016 034116 034216 034316 034416 034516 034616 034716 034816 034916 034A16 034B16 034C16 034D16 034E16 034F16 035016 035116 035216 035316 035416 035516 035616 035716 035816 035916 035A16 035B16 035C16 035D16 035E16 035F16 036016 Interrupt cause select register 2 Interrupt cause select register SI/O3 transmit/receive register IFSR2A IFSR S3TRR 00XXXXXX2 0016 ??16 SI/O3 control register SI/O3 bit rate generator SI/O4 transmit/receive register S3C S3BRG S4TRR 010000002 ??16 ??16 SI/O4 control register SI/O4 bit rate generator S4C S4BRG 010000002 ??16 UART0 special mode register 4 UART0 special mode register 3 UART0 special mode register 2 UART0 special mode register UART1 special mode register 4 UART1 special mode register 3 UART1 special mode register 2 UART1 special mode register UART2 special mode register 4 UART2 special mode register 3 UART2 special mode register 2 UART2 special mode register UART2 transmit/receive mode register UART2 bit rate generator UART2 transmit buffer register U0SMR4 U0SMR3 U0SMR2 U0SMR U1SMR4 U1SMR3 U1SMR2 U1SMR U2SMR4 U2SMR3 U2SMR2 U2SMR U2MR U2BRG U2TB UART2 transmit/receive control register 0 UART2 transmit/receive control register 1 UART2 receive buffer register U2C0 U2C1 U2RB 0016 000X0X0X2 X00000002 X00000002 0016 000X0X0X2 X00000002 X00000002 0016 000X0X0X2 X00000002 X00000002 0016 ??16 ????????2 XXXXXXX?2 000010002 000000102 ????????2 ?????XX?2 036116 036216 036316 036416 036516 036616 036716 036816 036916 036A16 036B16 036C16 036D16 036E16 036F16 037016 037116 037216 037316 037416 037516 037616 037716 037816 037916 037A16 037B16 037C16 037D16 037E16 037F16 Note : The blank areas are reserved and cannot be used by users. X : Nothing is mapped to this bit ? : Undefined Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 16 of 201 M16C/6S Group SFR Count start flag Register Symbol TABSR After reset 0016 One-shot start flag Trigger select register Up-down flag ONSF TRGSR UDF 0016 0016 0016 Timer A0 register TA0 Timer A1 register TA1 Timer A2 register TA2 Timer A3 register TA3 Timer A4 register TA4 ??16 ??16 ??16 ??16 ??16 ??16 ??16 ??16 ??16 ??16 Timer A0 mode register Timer A1 mode register Timer A2 mode register Timer A3 mode register Timer A4 mode register TA0MR TA1MR TA2MR TA3MR TA4MR 0016 0016 0016 0016 0016 03A016 UART0 transmit/receive mode register 03A116 UART0 bit rate generator UART0 transmit buffer register U0MR U0BRG U0TB Address 038016 038116 038216 038316 038416 038516 038616 038716 038816 038916 038A16 038B16 038C16 038D16 038E16 038F16 039016 039116 039216 039316 039416 039516 039616 039716 039816 039916 039A16 039B16 039C16 039D16 039E16 039F16 03AD16 UART1 transmit/receive control register 0 UART1 transmit/receive control register 1 03AE16 UART1 receive buffer register U1C0 U1C1 U1RB UART transmit/receive control register 2 UCON 0016 ??16 ????????2 XXXXXXX?2 000010002 000000102 ????????2 ?????XX?2 0016 ??16 ????????2 XXXXXXX?2 000010002 000000102 ????????2 ?????XX?2 X00000002 DMA0 request cause select register DM0SL 0016 DMA1 request cause select register DM1SL 0016 03A216 03A316 03A416 03A516 UART0 transmit/receive control register 0 UART0 transmit/receive control register 1 03A616 UART0 receive buffer register U0C0 U0C1 U0RB 03A716 03A816 UART1 transmit/receive mode register 03A916 UART1 bit rate generator UART1 transmit buffer register 03AA16 U1MR U1BRG U1TB 03AB16 03AC16 03AF16 03B016 03B116 03B216 03B316 03B416 03B516 03B616 03B716 03B816 03B916 03BA16 03BB16 03BC16 03BD16 03BE16 03BF16 Note : The blank areas are reserved and cannot be used by users. X : Nothing is mapped to this bit ? : Undefined Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 17 of 201 M16C/6S Group SFR Address Register Symbol After reset 03C016 03C116 03C216 03C316 03C416 03C516 03C616 03C716 03C816 03C916 03CA16 03CB16 03CC16 03CD16 03CE16 03CF16 03D016 03D116 03D216 03D316 03D416 03D516 03D616 03D716 03D816 03D916 03DA16 03DB16 03DC16 03DD16 03DE16 03DF16 03E016 03E116 Port P1 register P1 ??16 Port P1 direction register PD1 0016 Port P4 register Port P5 register Port P4 direction register Port P5 direction register Port P6 register Port P7 register Port P6 direction register Port P7 direction register Port P8 register Port P9 register Port P8 direction register Port P9 direction register P4 P5 PD4 PD5 P6 P7 PD6 PD7 P8 P9 PD8 PD9 ??16 ??16 0016 0016 ??16 ??16 0016 0016 ??16 ??16 00X000002 0016 Pull-up control register 0 Pull-up control register 1 Pull-up control register 2 Port control register PUR0 PUR1 PUR2 PCR 03E216 03E316 03E416 03E516 03E616 03E716 03E816 03E916 03EA16 03EB16 03EC16 03ED16 03EE16 03EF16 03F016 03F116 03F216 03F316 03F416 03F516 03F616 03F716 03F816 03F916 03FA 16 03FB16 03FC16 03FD16 03FE16 03FF16 Note 1: The blank areas are reserved and cannot be used by users. X : Nothing is mapped to this bit ? : Undefined Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 18 of 201 0016 000000002 0016 0016 M16C/6S Group Reset Reset There are four types of resets: a hardware reset, a software reset, an watchdog timer reset, and an oscillation stop detection reset. Hardware Reset ____________ ____________ A reset is applied using the RESET pin. When an “L” signal is applied to the RESET pin while the power supply voltage is within the recommended operating condition, the pins are initialized (see Table 1.5.1). The oscillation circuit is initialized and the main clock starts oscillating. When the input ____________ level at the RESET pin is released from “L” to “H”, the CPU and SFR are initialized, and the program is executed starting from the address indicated by the reset vector. The internal RAM is not initialized. ____________ If the RESET pin is pulled “L” while writing to the internal RAM, the internal RAM becomes indeterminate. Figure 1.5.1 shows the example reset circuit. Figure 1.5.2 shows the reset sequence. Table 1.5.1 ____________ shows the statuses of the other pins while the RESET pin is “L”. Figure 1.5.3 shows the CPU register status after reset. Refer to “SFR” for SFR status after reset. 1. When the power supply is stable ____________ (1) Apply an “L” signal to the RESET pin. (2) Supply a clock for 20 cycles or more to the XIN pin. ____________ (3) Apply an “H” signal to the RESET pin. 2. Power on ____________ (1) Apply an “L” signal to the RESET pin. (2) Let the power supply voltage increase until it meets the recommended operating condition. (3) Wait td(P-R) or more until the internal power supply stabilizes. (4) Supply a clock for 20 cycles or more to the XIN pin. ____________ (5) Apply an “H” signal to the RESET pin. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 19 of 201 M16C/6S Group Reset Software Reset When the PM03 bit in the PM0 register is set to “1” (microcomputer reset), the microcomputer has its pins, CPU, and SFR initialized. Then the program is executed starting from the address indicated by the reset vector. Select the main clock for the CPU clock source, and set the PM03 bit to “1” with main clock oscillation satisfactorily stable. At software reset, some SFR’s are not initialized. Refer to “SFR”. Also, since the PM01 to PM00 bits in the PM0 register are not initialized, the processor mode remains unchanged. Recommended operating voltage VCC 0V RESET VCC RESET 0V Equal to or less than 0.2VCC Equal to or less than 0.2VCC More than 20 cycles of XIN + td(P-R) are needed. Figure 1.5.1. Example Reset Circuit Watchdog Timer Reset Where the PM12 bit in the PM1 register is “1” (reset when watchdog timer underflows), the microcomputer initializes its pins, CPU and SFR if the watchdog timer underflows. Then the program is executed starting from the address indicated by the reset vector. At watchdog timer reset, some SFR’s are not initialized. Refer to “SFR”. Also, since the PM01 to PM00 bits in the PM0 register are not initialized, the processor mode remains unchanged. Oscillation Stop Detection Reset Where the CM27 bit in the CM2 register is “0” (reset at oscillation stop detection), the microcomputer initializes its pins, CPU and SFR, coming to a halt if it detects main clock oscillation circuit stop. Refer to the section “oscillation stop, re-oscillation detection function”. At oscillation stop detection reset, some SFR’s are not initialized. Refer to the section “SFR”. Also, since the PM01 to PM00 bits in the PM0 register are not initialized, the processor mode remains unchanged. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 20 of 201 M16C/6S Group Reset VCC1 XIN td(P-R) More than 20 cycles are needed RESET BCLK 28cycles BCLK Single chip mode FFFFC16 FFFFE16 Internal address Figure 1.5.2. Reset Sequence Rev.5.01 Dec 10, 2009 REJ03B0014-0501 Content of reset vector page 21 of 201 M16C/6S Group Reset ____________ Table 1.5.1. Pin Status When RESET Pin Level is “L” Status Pin name CNVSS = VSS P15, P60 to P67, P70, P71, P73, P74, P76, P80, P81, P83, P84, P85, P90 to P92, TS Input port b15 b0 000016 Data register(R0) 000016 Data register(R1) 000016 Data register(R2) 000016 Data register(R3) 000016 000016 Address register(A0) Address register(A1) 000016 Frame base register(FB) b19 b0 0000016 Interrupt table register(INTB) Content of addresses FFFFE16 to FFFFC16 b15 Program counter(PC) b0 000016 User stack pointer(USP) 000016 Interrupt stack pointer(ISP) 000016 Static base register(SB) b15 b0 Flag register(FLG) 000016 b15 b8 IPL b7 U I b0 O B S Z D C Figure 1.5.3. CPU Register Status After Reset Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 22 of 201 M16C/6S Group Processor Mode Processor Mode (1) Setting Processor Modes Processor mode is available only: single-chip mode. Processor mode is set by using the CNVSS pin and the PM01 to PM00 bits in the PM0 register. Table 1.6.1 shows the processor mode after hardware reset. Table 1.6.2 shows the PM01 to PM00 bits set values and processor modes. For setting Single-chip mode. CNVss should be kept Vss level. And PM01 to PM00 of PM0 register should be set "00." Table 1.6.1. Processor Mode After Hardware Reset CNVSS pin input level VSS VCC Processor mode Single-chip mode Flash Memory Mode Table 1.6.2. PM01 to PM00 Bits Set Values and Processor Modes PM01 to PM00 bits 002 Processor modes Single-chip mode 012 102 Must not be set 11 2 Figure 1.6.4 show the memory map in single chip mode. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 23 of 201 M16C/6S Group Processor Mode (2) Setting PLC Mode PLC mode is simply set by putting P15 High level during RESET. TR RESET P15 Tsetup Figure 1.6.1. PLC mode by P15 simply setting Table 1.6.3. RESET and P15 Input min TR 40us Tset up 5us THOLD 5us Rev.5.01 Dec 10, 2009 REJ03B0014-0501 typ max page 24 of 201 THOLD M16C/6S Group Processor Mode Processor mode register 0 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol PM0 Address 000416 Bit symbol PM00 Bit name Processor mode bit (Note 2) PM01 (b2) PM03 (b7-b4) After reset (Note 2) XXXX0X002 (CNVSS pin = “L”) Function RW b1 b0 RW 0 0: Single-chip mode 0 1: Must not be set 1 0: Must not be set 1 1: Must not be set RW Nothing is assigned. When write, set to “0”. When read, its content is indeterminate. Software reset bit Setting this bit to “1” resets the microcomputer. When read, its content is “0”. Nothing is assigned. When write, set to “0”. When read, their contents are indeterminate. Note 1: Write to this register after setting the PRC1 bit in the PRCR register to "1" (write enable). Note 2: The PM01 to PM00 bits do not change at software reset, watchdog timer reset and oscillation stop detection reset. Figure 1.6.2. PM0 Register Processor mode register 1 (Note 1) b7 b6 0 b5 b4 b3 b2 1 b1 b0 0 Symbol PM1 Bit symbol (b0) (b2) Address 000516 After reset 00XX10X02 Bit name Reserved bit Function Should be set to “0”. RW RW Nothing is assigned. When write, set to “0”. When read, its content is indeterminate. PM12 Watchdog timer function select bit 0 : Watchdog timer interrupt 1 : Watchdog timer reset (Note 2) RW PM13 Internal reserved area expansion bit Should be set to “1”. RW (b5-b4) (b6) PM17 Nothing is assigned. When write, set to “0”. When read, its content is indeterminate. Reserved bit Should be set to “0”. Wait bit (Note 3) 0 : No wait state 1 : With wait state (1 wait) RW RW Note 1: Write to this register after setting the PRC1 bit in the PRCR register to “1” (write enable). Note 2: PM12 bit is set to “1” by writing a “1” in a program. (Writing a “0” has no effect.) Note 3: When PM17 bit is set to “1” (with wait state), one wait state is inserted when accessing the internal RAM, internal ROM, or an external area. Figure 1.6.3. PM1 Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 25 of 201 RW M16C/6S Group Processor Mode Single-chip mode 0000016 SFR 0040016 Internal RAM XXXXX16 PM13=1 (Note1) Internal RAM Capacity Address XXXXX16 Can not use 24K bytes 063FF16 Internal ROM Capacity Address YYYYY16 64K bytes F000016 96K bytes E800016 YYYYY16 Internal ROM FFFFF16 Note 1: Since internal RAM which can be used becomes 15 K bytes when PM13 is “0”, please be sure to set PM13 to “1”. Figure 1.6.4. Memory Map in Single Chip Mode Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 26 of 201 M16C/6S Group Clock Generation Circuit Clock Generation Circuit The clock generation circuit contains two oscillator circuits as follows: (1) Main clock oscillation circuit (2) On-chip Oscillator (oscillation stop detect function) Table 1.7.1 lists the clock generation circuit specifications. Figure 1.7.1 shows the clock generation circuit. Figures 1.7.2 to 1.7.5 show the clock-related registers. Table 1.7.1. Clock Generation Circuit Specifications Main clock oscillation circuit Item On-chip Oscillator Use of clock • CPU clock source • Peripheral function clock source • CPU clock source • Peripheral function clock source Clock frequency 5.12 MHz About 1 MHz Usable oscillator • Crystal oscillator (Note 1) Pins to connect oscillator XIN, XOUT Oscillation stop, restart function No Presence Oscillator status after reset Oscillating Stopped Other Externally derived clock can be input Note. Operating frequency must be 5.12 MHz, overall accuracy must be less than 150 ppm. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 27 of 201 M16C/6S Group Clock Generation Circuit f1 PCLK0=1 f2 XIN PCLK0=0 XOUT f8 5.12MHz CM21 Standard serial I/O mode (5.12MHz) On-chip oscillator On-chip oscillator clock f32 fAD 46.08MHz PLL Oscillation stop, reoscillation detection circuit 1/3 Normal operation mode IT800 CLK_IN (15.36MHz) f1SIO PCLK1=1 f2SIO PCLK1=0 f8SIO CM10=1(stop mode) S Q f32SIO e b c R a CM21=1 d Divider Main clock CM07=0 CPU clock CM21=0 BCLK CM02 S WAIT instruction Q R e 1/2 a c b 1/2 1/2 1/2 1/2 1/32 RESET 1/2 1/4 1/8 Software reset 1/16 CM06=0 CM17–CM16=11 2 CM06=1 CM06=0 CM17–CM16=102 Interrupt request level judgment output CM02, CM04, CM05, CM06, CM07: CM0 register bits CM10, CM11, CM16, CM17: CM1 register bits PCLK0, PCLK1: PCLK register bits CM21, CM27 : CM2 register bits d CM06=0 CM17–CM16=012 CM06=0 CM17–CM16=002 Details of divider Oscillation stop, re-oscillation detection circuit(Note) Main clock Pulse generation circuit for clock edge detection and charge, discharge control CM27 Charge, discharge circuit 0 1 Reset generating circuit Oscillation stop, re-oscillation detection interrupt generating circuit Oscillation stop detection reset Oscillation stop, re-oscillation detection signal CM21 switch signal Note. Even if XIN input stops, PLL does not stop. Oscillation stop, re-oscillation detect circuit does not function. Figure 1.7.1. Clock Generation Circuit Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 28 of 201 M16C/6S Group Clock Generation Circuit System clock control register 0 (Notes 1 and 4) b7 0 b6 b5 b4 b3 b2 b1 0 b0 Symbol CM0 Address 000616 Bit symbol After reset 010010002 Bit name Function (b1-b0) Nothing is assigned. When write, set to “0”. When read, its content is indeterminate. CM02 WAIT peripheral function clock stop bit (Note 3) (b4-b3) Nothing is assigned. When write, set to “0”. When read, its content is indeterminate. (b5) CM06 (b7) 0 : Do not stop peripheral function clock in wait mode 1 : Stop peripheral function clock in wait mode RW RW Reserved bit Should be set to “0”. RW Main clock division select bit 0 (Notes 5, 13) 0 : CM16 and CM17 valid 1 : Division by 8 mode RW Reserved bit Should be set to “0”. RW Note 1: Write to this register after setting the PRC0 bit of PRCR register to “1” (write enable). Note 2: When entering stop mode from high or middle speed mode, On-chip Oscillator mode or On-chip Oscillator low power mode, the CM06 bit is set to “1” (divide-by-8 mode). Note 3: When the PM21 bit of PM2 register is set to “1” (clock modification disable), writing to the CM02 bits has no effect. Note 4: To use the main clock as the clock source for the CPU clock, follow the procedure below. (1) Wait until td(M-L) elapses or the main clock oscillation stabilizes, whichever is longer. (2) Set the CM21 to “0”. Note 5: During On-chip Oscillator low power dissipation mode, the divide-by-n value can be selected using the CM06 and CM17 to CM16 bits. To return to high or middle speed mode, however, set the CM06 bit to “1”, before selecting the desired mode. Figure 1.7.2. CM0 Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 29 of 201 M16C/6S Group Clock Generation Circuit System clock control register 1 (Note 1) b7 b6 b5 b4 1 0 0 b3 b2 b1 0 0 b0 Symbol CM1 Address 000716 Bit symbol CM10 (b4-b1) (b5) CM16 After reset 001000002 Bit Function RW name All clock stop control bit (Notes 3, 4) 0 : Clock on 1 : All clocks off (stop mode) RW Reserved bit Must set to “0” RW Must set to “1” RW Reserved bit Main clock division select bit 1 (Note 2) CM17 b7 b6 0 0 : No division mode 0 1 : Division by 2 mode 1 0 : Division by 4 mode 1 1 : Division by 16 mode RW RW Note 1: Write to this register after setting the PRC0 bit of PRCR register to “1” (write enable). Note 2: Effective when the CM06 bit is “0” (CM16 and CM17 bits enable). Note 3: When the CM20 bit of CM2 register is set to “1” (oscillation stop, re-oscillation detection function enabled), do not set the CM10 bit to “1”. Note 4: When the PM21 bit of PM2 register is set to “1” (clock modification disable), writing to the CM10 bits has no effect. When the PM22 bit of PM2 register is set to “1” (watchdog timer count source is On-chip Oscillator clock), writing to the CM10 bit has no effect. Figure 1.7.3. CM1 Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 30 of 201 M16C/6S Group Clock Generation Circuit Oscillation stop detection register (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol CM2 Bit symbol CM20 CM21 CM22 CM23 (b5-b4) (b6) Address 000C16 After reset 0X0000002(Note 10) Bit name Function RW Oscillation stop, reoscillation detection bit (Notes 7, 8, 9, 10) 0: Oscillation stop, re-oscillation detection function disabled 1: Oscillation stop, re-oscillation detection function enabled RW System clock select bit 2 (Notes 2, 3, 6, 10) 0: Main clock (On-chip Oscillator turned off) 1: On-chip Oscillator clock (On-chip Oscillator oscillating) RW Oscillation stop, reoscillation detection flag (Note 4) 0: Main clock stop, re-oscillation not detected 1: Main clock stop, re-oscillation detected RW XIN monitor flag (Note 5) 0: Main clock oscillating 1: Main clock turned off RO Reserved bit Must set to “0” RW Nothing is assigned. When write, set to “0”. When read, its content is indeterminate. 0: Oscillation stop detection reset Operation select bit (when an oscillation stop, 1: Oscillation stop, re-oscillation RW detection interrupt re-oscillation is detected) (Note 10) Note 1: Write to this register after setting the PRC0 bit of PRCR register to “1” (write enable). Note 2: When the CM20 bit is “1” (oscillation stop, re-oscillation detection function enabled), the CM27 bit is “1” (oscillation stop, re-oscillation detection interrupt), and the CPU clock source is the main clock, the CM21 bit is set to “1” (On-chip Oscillator clock) if the main clock stop is detected. Note 3: If the CM20 bit is “1” and the CM23 bit is “1” (main clock turned off), do not set the CM21 bit to “0”. Note 4: This bit becomes “1” at main clock stop detection and main clock re-oscillation detection. When this bit changes from “0” to “1”, there arise oscillation stop, re-oscillation detection interrupt. Use this register to discriminate the causes for oscillation stop, re-oscillation detection interrupt and watchdog timer interrupt in the interrupt processing program. By writing “0” in the program, this bit becomes “0”. (Even when “1” is written in the program, no change is identified for the bit. Also, this bit is not set to “0” where there occur oscillation stop, re-oscillation detection interrupt.) When the CM22 bit is “1”, no oscillation stop, reoscillation detection interrupt occur even if oscillation stop or re-oscillation is detected. Note 5: Read the CM23 bit in an oscillation stop, re-oscillation detection interrupt handling routine to determine the main clock status. Note 6: Effective when the CM07 bit of CM0 register is “0”. Note 7: When the PM21 bit of PM2 register is “1” (clock modification disabled), writing to the CM20 bit has no effect. Note 8: Set the CM20 bit to “0” (disable) before entering stop mode. After exiting stop mode, set the CM20 bit back to “1” (enable). Note 9: Set the CM20 bit to “0” (disable) before setting the CM05 bit of CM0 register. Note 10: The CM20, CM21 and CM27 bits do not change at oscillation stop detection reset. CM27 Figure 1.7.4. CM2 Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 31 of 201 M16C/6S Group Clock Generation Circuit Peripheral clock select register (Note) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 Symbol PCLKR Address 025E16 Bit symbol Bit name PCLK0 Timers A, B clock select bit (Clock source for the timers A, B, and the dead time timer) PCLK1 (b7-b2) When reset 000000112 Function RW 0 : f2 1 : f1 RW SI/O clock select bit (Clock source for UART0 to UART2, SI/O3, SI/O4) 0 : f2SIO 1 : f1SIO RW Reserved bit Must set to “0” RW Note: Write to this register after setting the PRC0 bit of PRCR register to “1” (write enable). Processor mode register 2 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol PM2 Bit symbol (b0) Address 001E16 Bit name After reset XXX000002 Function RW Nothing is assigned. When write, set to “0”. When read, its content is interdeterminate. PM21 System clock protective bit (Note 2, Note 3) 0 : Clock is protected by PRCR register 1 : Clock modification disabled PM22 WDT count source protective bit (Note 2, Note 4) 0 : CPU clock is used for the watchdog timer count source RW 1 : On-chip Oscillator clock is used for the watchdog timer count source Reserved bit Must set to “0” (b4-b3) (b7-b5) RW RW Nothing is assigned. When write, set to “0”. When read, its content is interdeterminate. Note 1: Write to this register after setting the PRC1 bit of PRCR register to “1” (write enable). Note 2: Once this bit is set to “1”, it cannot be cleared to “0” in a program. Note 3: Setting the PM21 bit to “1” results in the following conditions: • The BCLK is not halted by executing the WAIT instruction. • Writing to the following bits has no effect. CM02 bit of CM0 register CM05 bit of CM0 register (main clock is not halted) CM07 bit of CM0 register CM10 bit of CM1 register (stop mode is not entered) CM11 bit of CM1 register CM20 bit of CM2 register (oscillation stop, re-oscillation detection function settings do not change) Note 4: Setting the PM22 bit to “1” results in the following conditions: • The On-chip Oscillator starts oscillating, and the On-chip Oscillator clock becomes the watchdog timer count source. • The CM10 bit of CM1 register is disabled against write. (Writing a “1” has no effect, nor is stop mode entered.) • The watchdog timer does not stop when in wait mode or hold state. Figure 1.7.5. PCLKR Register and PM2 Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 32 of 201 M16C/6S Group Clock Generation Circuit The following describes the clocks generated by the clock generation circuit. (1) Main Clock Main clock is supplied by IT800 with a tripled clock of XIN (main clock oscillator). This clock is used as the clock source for the CPU and peripheral function clocks. The main clock oscillator circuit is configured by connecting a resonator between the XIN and XOUT pins. The main clock oscillator circuit contains a feedback resistor. The main clock oscillator circuit may also be configured by feeding an externally generated clock to the XIN pin. Figure 1.7.6 shows the examples of main clock connection circuit. After reset, the main clock divided by 8 is selected for the CPU clock. Even if XIN input stops, main clock oscillator does not stop. During stop mode, all clocks of internal M16C core including the main clock are turned off. Refer to “power control”. Microcomputer Microcomputer (Built-in feedback resistor) (Built-in feedback resistor) XIN XIN XOUT (Note 2) CIN XOUT Open (Note 1) Rd Externally derived clock COUT Vcc Vss Note 1: Insert a damping resistor if required. The resistance will vary depending on the oscillator and the oscillation drive capacity setting. Use the value recommended by the maker of the oscillator. Also, if the oscillator manufacturer's data sheet specifies that a feedback resistor be added external to the chip, insert a feedback resistor between XIN and XOUT following the instruction. Note 2: Operating frequency must be 5.12 MHz, overall accuracy must be less than 150 ppm. Figure 1.7.6. Examples of Main Clock Connection Circuit Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 33 of 201 M16C/6S Group Clock Generation Circuit (3) On-chip Oscillator Clock This clock, approximately 1 MHz, is supplied by a On-chip Oscillator. This clock is used as the clock source for the CPU and peripheral function clocks. In addition, if the PM22 bit of PM2 register is “1” (Onchip Oscillator clock for the watchdog timer count source), this clock is used as the count source for the watchdog timer. After reset, the On-chip Oscillator clock is turned off. It is turned on by setting the CM21 bit of CM2 register to “1” (On-chip Oscillator clock), and is used as the clock source for the CPU and peripheral function clocks, in place of the main clock. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 34 of 201 M16C/6S Group Clock Generation Circuit CPU Clock and Peripheral Function Clock Two type clocks: CPU clock to operate the CPU and peripheral function clocks to operate the peripheral functions. (1) CPU Clock and BCLK These are operating clocks for the CPU and watchdog timer. The clock source for the CPU clock can be chosen to be the main clock, or On-chip Oscillator clock. If the main clock or On-chip Oscillator clock is selected as the clock source for the CPU clock, the selected clock source can be divided by 1 (undivided), 2, 4, 8 or 16 to produce the CPU clock. Use the CM06 bit in CM0 register and the CM17 to CM16 bits in CM1 register to select the divide-by-n value. After reset, the main clock divided by 8 provides the CPU clock. Note that when entering stop mode from high or middle speed mode or On-chip Oscillator mode, the CM06 bit of CM0 register is set to “1” (divide-by-8 mode). (2) Peripheral Function Clock(f1, f2, f8, f32, f1SIO, f2SIO, f8SIO, f32SIO) These are operating clocks for the peripheral functions. Of these, fi (i = 1, 2, 8, 32) and fiSIO are derived from the main clock, or On-chip Oscillator clock by dividing them by i. The clock fi is used for timers A, and fiSIO is used for serial I/O. When the WAIT instruction is executed after setting the CM02 bit of CM0 register to “1” (peripheral function clock turned off during wait mode), or when the microcomputer is in low power dissipation mode, the fi, and fiSIO clocks are turned off. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 35 of 201 M16C/6S Group Clock Generation Circuit Power Control There are three power control modes. For convenience’ sake, all modes other than wait and stop modes are referred to as normal operation mode here. (1) Normal Operation Mode Normal operation mode is further classified into three modes. In normal operation mode, because the CPU clock and the peripheral function clocks both are on, the CPU and the peripheral functions are operating. Power control is exercised by controlling the CPU clock frequency. The higher the CPU clock frequency, the greater the processing capability. The lower the CPU clock frequency, the smaller the power consumption in the chip. If the unnecessary oscillator circuits are turned off, the power consumption is further reduced. Before the clock sources for the CPU clock can be switched over, the new clock source to which switched must be oscillating stably. If the new clock source is the main clock, allow a sufficient wait time in a program until it becomes oscillating stably. Where the CPU clock source is changed from the On-chip Oscillator to the main clock, change the operation mode to the medium speed mode (divided by 8 mode) after the clock was divided by 8 (the CM06 bit of CM0 register was set to “1”) in the On-chip Oscillator mode. • High-speed Mode The main clock divided by 1 provides the CPU clock. • Medium-speed Mode The main clock divided by 2, 4, 8 or 16 provides the CPU clock. • On-chip Oscillator Mode The On-chip Oscillator clock divided by 1 (undivided), 2, 4, 8 or 16 provides the CPU clock. The Onchip Oscillator clock is also the clock source for the peripheral function clocks. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 36 of 201 M16C/6S Group Clock Generation Circuit Table 1.7.2. Setting Clock Related Bit and Modes Modes High-speed mode Mediumdivided by 2 speed divided by 4 mode divided by 8 divided by 16 On-chip divided by 1 oscillator divided by 2 mode divided by 4 divided by 8 divided by 16 CM2 register CM21 0 0 0 0 0 1 1 1 1 1 CM1 register CM17, CM16 002 012 102 112 002 012 102 112 CM0 register CM06 0 0 0 1 0 0 0 0 1 0 Note: The divide-by-n value can be selected the same way as in On-chip Oscillator mode. (2) Wait Mode In wait mode, the CPU clock is turned off, so are the CPU (because operated by the CPU clock) and the watchdog timer. However, if the PM22 bit of PM2 register is “1” (On-chip Oscillator clock for the watchdog timer count source), the watchdog timer remains active. Because the main clock, and On-chip Oscillator clock are on, the peripheral functions using these clocks keep operating. • Peripheral Function Clock Stop Function If the CM02 bit is “1” (peripheral function clocks turned off during wait mode), the f1, f2, f8, f32, f1SIO, f8SIO, and f32SIO clocks are turned off when in wait mode, with the power consumption reduced that much. • Entering Wait Mode The microcomputer is placed into wait mode by executing the WAIT instruction. • Pin Status During Wait Mode Table 1.7.3 lists pin status during wait mode • Exiting Wait Mode The microcomputer is moved out of wait mode by a hardware reset or peripheral function interrupt. If the microcomputer is to be moved out of exit wait mode by a hardware reset, set the peripheral function interrupt priority ILVL2 to ILVL0 bits to “0002” (interrupts disabled) before executing the WAIT instruction. The peripheral function interrupts are affected by the CM02 bit. If CM02 bit is “0” (peripheral function clocks not turned off during wait mode), all peripheral function interrupts can be used to exit wait mode. If CM02 bit is “1” (peripheral function clocks turned off during wait mode), the peripheral functions using the peripheral function clocks stop operating, so that only the peripheral functions clocked by external signals can be used to exit wait mode. Table 1.7.4 lists the interrupts to exit wait mode. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 37 of 201 M16C/6S Group Clock Generation Circuit Table 1.7.3. Pin Status During Wait Mode Pin Status Retains status before wait mode I/O ports Table 1.7.4. Interrupts to Exit Wait Mode Interrupt CM02=0 CM02=1 Serial I/O interrupt Can be used when operating with internal or external clock Can be used when operating with external clock Timer A interrupt Can be used in all modes Can be used in event counter mode INT interrupt Can be used Can be used If the microcomputer is to be moved out of wait mode by a peripheral function interrupt, set up the following before executing the WAIT instruction. 1. In the ILVL2 to ILVL0 bits of interrupt control register, set the interrupt priority level of the periph eral function interrupt to be used to exit wait mode. Also, for all of the peripheral function interrupts not used to exit wait mode, set the ILVL2 to ILVL0 bits to “0002” (interrupt disable). 2. Set the I flag to “1”. 3. Enable the peripheral function whose interrupt is to be used to exit wait mode. In this case, when an interrupt request is generated and the CPU clock is thereby turned on, an interrupt routine is executed. The CPU clock turned on when exiting wait mode by a peripheral function interrupt is the same CPU clock that was on when the WAIT instruction was executed. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 38 of 201 M16C/6S Group Clock Generation Circuit (3) Stop Mode In stop mode, all the M16C core's internal oscillator circuits are turned off, so are the CPU clock and the peripheral function clocks. Therefore, the CPU and the peripheral functions clocked by these clocks stop operating. However, the peripheral functions clocked by external signals keep operating. The following interrupts can be used to exit stop mode. ______ • INT interrupt • Timer A, interrupt (when counting external pulses in event counter mode) • Serial I/O interrupt (when external clock is selected) • Entering Stop Mode The microcomputer is placed into stop mode by setting the CM10 bit of CM1 register to “1” (all clocks turned off). At the same time, the CM06 bit of CM0 register is set to “1” (divide-by-8 mode). Before entering stop mode, set the CM20 bit to “0” (oscillation stop, re-oscillation detection function disable). • Pin Status in Stop Mode Table 1.7.5 lists pin status during stop mode • Exiting Stop Mode The microcomputer is moved out of stop mode by a hardware reset or peripheral function interrupt. If the microcomputer is to be moved out of stop mode by a hardware reset, set the peripheral function interrupt priority ILVL2 to ILVL0 bits to “0002” (interrupts disable) before setting the CM10 bit to “1”. If the microcomputer is to be moved out of stop mode by a peripheral function interrupt, set up the following before setting the CM10 bit to “1”. 1. In the ILVL2 to ILVL0 bits of interrupt control register, set the interrupt priority level of the peripheral function interrupt to be used to exit stop mode. Also, for all of the peripheral function interrupts not used to exit stop mode, set the ILVL2 to ILVL0 bits to “0002”. 2. Set the I flag to “1”. 3. Enable the peripheral function whose interrupt is to be used to exit stop mode. In this case, when an interrupt request is generated and the CPU clock is thereby turned on, an interrupt service routine is executed. Which CPU clock will be used after exiting stop mode by a peripheral function is determined by the CPU clock that was on when the microcomputer was placed into stop mode as follows: If the CPU clock before entering stop mode was derived from the main clock: main clock divide-by-8 If the CPU clock before entering stop mode was derived from the On-chip Oscillator clock: On-chip Oscillator clock divide-by-8 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 39 of 201 M16C/6S Group Clock Generation Circuit Table 1.7.5. Pin Status in Stop Mode Pin Status Retains status before stop mode I/O ports Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 40 of 201 M16C/6S Group Clock Generation Circuit Figure 1.7.7 shows the state transition from normal operation mode to stop mode and wait mode. Reset All oscillators stopped Stop mode CM10=1 Interrupt Medium-speed mode (divided-by-8 mode) Interrupt CM10=1 CM10=1 Stop mode CPU operation stopped Wait mode Interrupt WAIT instruction (Note 1) High-speed, mediumspeed mode Stop mode WAIT instruction (Note 1) On-chip Oscillator mode Wait mode Interrupt WAIT instruction (Note 1) Interrupt Interrupt (Note 2) Wait mode Normal mode Note 1: When the PM21 bit = 0 (system clock protective function unused). Note 2: The On-chip Oscillator clock divided by 8 provides the CPU clock. Note 3: Write to the CM0 register and CM1 register simultaneously by accessing in word units while CM21=0 (On-chip Oscillator turned off). Figure 1.7.7. State Transition to Stop Mode and Wait Mode Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 41 of 201 M16C/6S Group Clock Generation Circuit Main clock oscillation On-chip Oscillator clock oscillation High-speed mode CPU clock: f(XIN) Middle-speed mode (divide by 2) CPU clock: f(XIN)/2 Middle-speed mode (divide by 4) CPU clock: f(XIN)/4 CM07=0 CM07=0 CM07=0 CM06=0 CM06=0 CM06=0 CM17=0 CM17=0 CM17=1 CM16=0 CM16=1 CM16=0 Middle-speed mode Middle-speed mode (divide by 8) (divide by 16) CPU clock: f(XIN)/8 CM07=0 CM06=1 CPU clock: f(XIN)/16 On-chip Oscillator mode CM21=0 (Note 4) CM07=0 CM06=0 CM17=1 CM16=1 CM21=1 CPU clock f(Ring) f(Ring)/2 f(Ring)/4 f(Ring)/8 f(Ring)/16 (Note 2) (Note 3) Notes: 1: Avoid making a transition when the CM20 bit in the CM2 register is set to “1” (oscillation stop, re-oscillation detection function enabled). Set the CM20 bit to “0” (oscillation stop, re-oscillation detection function disabled) before transiting. 2: Change CM17 and CM16 bits in the CM1 register before changing CM06 bit in the CM0 register. 3: Transit in accordance with arrow. 4: Set the CM06 to “1” (division by 8 mode) before changing back the operation mode from on-chip oscillator mode to high- or middle-speed mode. Figure 1.7.8. State Transition in Normal Mode Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 42 of 201 M16C/6S Group Clock Generation Circuit Table 1.7.6. Allowed Transition and Setting State after transition High-speed mode, On-chip Oscillator middle-speed mode mode Current state Stop mode See Table A (7) (8)1 On-chip Oscillator mode (6)2 See Table A (8)1 Stop mode (10)3 (10)3 (10) (10) High-speed mode, middle-speed mode Wait mode Wait mode (9) (9) -- ---: Cannot transit Table 1. State Transition with Main Clock Division Ration in High- or Middle-speed Mode and On-chip Oscillator Mode. Table B. Setting and Operation State after transition No division (2) No division Current state Divided by 2 Divided by 4 Setting Divided Divided by 8 by 16 (3) (5) (4) (3) (5) (4) (5) (4) Divided by 2 (1) Divided by 4 (1) (2) Divided by 8 (1) (2) (3) Divided by 16 (1) (2) (3) (4) (5) Notes: 1. Avoid making a transition when the CM21 bit is set to “1” (oscillation stop, re-oscillation detection function enabled). Set the CM21 bit to “0” (oscillation stop, re-oscillation detection function disabled) before transiting. 2. Set the CM06 bit to “1” (division by 8 mode) before transiting from On-chip Oscillator mode to high- or middle-speed mode. 3. When exiting stop mode, the CM06 bit is set to “1” (division by 8 mode). (1) (2) (3) (4) (5) CPU clock no division mode CPU clock division by 2 mode CPU clock division by 4 mode CPU clock division by 16 mode CPU clock division by 8 mode CM21 = 0 Main clock (7) CM21 = 1 On-chip Oscillator clock selected (8) CM10 = 1 Transition to stop mode (10) page 43 of 201 CM06 = 1 Operation (6) (9) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 CM06 = 0, CM17 = 0 , CM16 = 0 CM06 = 0, CM17 = 0 , CM16 = 1 CM06 = 0, CM17 = 1 , CM16 = 0 CM06 = 0, CM17 = 1 , CM16 = 1 wait Hardware interrupt Transition to wait mode Exit stop mode or wait mode M16C/6S Group Clock Generation Circuit System Clock Protective Function When the main clock is selected for the CPU clock source, this function disables the clock against modifications in order to prevent the CPU clock from becoming halted by run-away. If the PM21 bit of PM2 register is set to “1” (clock modification disabled), the following bits are protected against writes: • CM02 bit in CM0 register • CM10, CM11 bits in CM1 register • CM20 bit in CM2 register Before the system clock protective function can be used, the following register settings must be made: (1) Set the PRC1 bit of PRCR register to “1” (enable writes to PM2 register). (2) Set the PM21 bit of PM2 register to “1” (disable clock modification). (3) Set the PRC1 bit of PRCR register to “0” (disable writes to PM2 register). Do not execute the WAIT instruction when the PM21 bit is “1”. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 44 of 201 M16C/6S Group Clock Generation Circuit Oscillation Stop and Re-oscillation Detect Function The oscillation stop and re-oscillation detect function is such that main clock oscillation circuit stop and reoscillation are detected. At oscillation stop, re-oscillation detection, reset or oscillation stop, re-oscillation detection interrupt are generated. Which is to be generated can be selected using the CM27 bit of CM2 register. Main clock oscillator of M16C/6S does not stop even if Xin input stops. Oscillation stop re-oscillation detect circuit does not function. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 45 of 201 M16C/6S Group Protection Protection In the event that a program runs out of control, this function protects the important registers so that they will not be rewritten easily. Figure 1.8.1 shows the PRCR register. The following lists the registers protected by the PRCR register. • Registers protected by PRC0 bit: CM0, CM1, CM2, and PCLKR registers • Registers protected by PRC1 bit: PM0, PM1, PM2 registers • Registers protected by PRC2 bit: PD9, S3C and S4C registers Set the PRC2 bit to “1” (write enabled) and then write to any address, and the PRC2 bit will be cleared to “0” (write protected). The registers protected by the PRC2 bit should be changed in the next instruction after setting the PRC2 bit to “1”. Make sure no interrupts or DMA transfers will occur between the instruction in which the PRC2 bit is set to “1” and the next instruction. The PRC0 and PRC1 bits are not automatically cleared to “0” by writing to any address. They can only be cleared in a program. Protect register b7 b6 b5 b4 b3 b2 0 0 0 b1 b0 Symbol PRCR Address 000A16 Bit symbol Bit name PRC0 Protect bit 0 After reset XX0000002 Function Enable write to CM0, CM1, CM2, PLC0 and PCLKR registers 0 : Write protected 1 : Write enabled PRC1 Protect bit 1 RW Enable write to PM0, PM1, PM2, TB2SC, INVC0 and INVC1 registers RW RW 0 : Write protected 1 : Write enabled PRC2 Protect bit 2 Enable write to PD9, S3C and S4C registers 0 : Write protected 1 : Write enabled Reserved bit (b5-b3) (b7-b6) Must set to “0” RW RW Nothing is assigned. When write, set to “0”. When read, its content is interdeterminate. Note: The PRC2 bit is set to “0” by writing to any address after setting it to “1”. Other bits are not set to “0” by writing to any address, and must therefore be set in a program. Figure 1.8.1. PRCR Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 46 of 201 M16C/6S Group Interrupts Interrupts Type of Interrupts Figure 1.9.1 shows types of interrupts. Hardware Special (Non-maskable interrupt) Interrupt Software (Non-maskable interrupt) Undefined instruction (UND instruction) Overflow (INTO instruction) BRK instruction INT instruction ________ DBC (Note 2) Watchdog timer Single step (Note 2) Address match Peripheral function (Note 1) (Maskable interrupt) Note 1: Peripheral function interrupts are generated by the microcomputer's internal functions. Note 2: Do not normally use this interrupt because it is provided exclusively for use by development support tools. Figure 1.9.1. Interrupts • Maskable Interrupt: An interrupt which can be enabled (disabled) by the interrupt enable flag (I flag) or whose interrupt priority can be changed by priority level. • Non-maskable Interrupt: An interrupt which cannot be enabled (disabled) by the interrupt enable flag (I flag) or whose interrupt priority cannot be changed by priority level. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 47 of 201 M16C/6S Group Interrupts Software Interrupts A software interrupt occurs when executing certain instructions. Software interrupts are non-maskable interrupts. • Undefined Instruction Interrupt An undefined instruction interrupt occurs when executing the UND instruction. • Overflow Interrupt An overflow interrupt occurs when executing the INTO instruction with the O flag set to “1” (the operation resulted in an overflow). The following are instructions whose O flag changes by arithmetic: ABS, ADC, ADCF, ADD, CMP, DIV, DIVU, DIVX, NEG, RMPA, SBB, SHA, SUB • BRK Interrupt A BRK interrupt occurs when executing the BRK instruction. • INT Instruction Interrupt An INT instruction interrupt occurs when executing the INT instruction. Software interrupt Nos. 0 to 63 can be specified for the INT instruction. Because software interrupt Nos. 4 to 31 are assigned to peripheral function interrupts, the same interrupt routine as for peripheral function interrupts can be executed by executing the INT instruction. In software interrupt Nos. 0 to 31, the U flag is saved to the stack during instruction execution and is cleared to “0” (ISP selected) before executing an interrupt sequence. The U flag is restored from the stack when returning from the interrupt routine. In software interrupt Nos. 32 to 63, the U flag does not change state during instruction execution, and the SP then selected is used. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 48 of 201 M16C/6S Group Interrupts Hardware Interrupts Hardware interrupts are classified into two types — special interrupts and peripheral function interrupts. (1) Special Interrupts Special interrupts are non-maskable interrupts. ________ • DBC Interrupt Do not normally use this interrupt because it is provided exclusively for use by development support tools. • Watchdog Timer Interrupt Generated by the watchdog timer. Once a watchdog timer interrupt is generated, be sure to initialize the watchdog timer. For details about the watchdog timer, refer to the section "watchdog timer". • Oscillation Stop and Re-oscillation Detection Interrupt Generated by the oscillation stop and re-oscillation detection function. For details about the oscillation stop detection function, refer to the section "clock generating circuit". • Single-step Interrupt Do not normally use this interrupt because it is provided exclusively for use by development support tools. • Address Match Interrupt An address match interrupt is generated immediately before executing the instruction at the address indicated by the RMAD0 to RMAD3 register that corresponds to one of the AIER register’s AIER0 or AIER1 bit or the AIER2 register’s AIER20 or AIER21 bit which is "1" (address match interrupt enabled). For details about the address match interrupt, refer to the section "address match interrupt". (2) Peripheral Function Interrupts Peripheral function interrupts are maskable interrupts and generated by the microcomputer's internal functions. The interrupt sources for peripheral function interrupts are listed in Table 1.9.1. For details about the peripheral functions, refer to the description of each peripheral function in this manual. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 49 of 201 M16C/6S Group Interrupts Interrupts and Interrupt Vector One interrupt vector consists of 4 bytes. Set the start address of each interrupt routine in the respective interrupt vectors. When an interrupt request is accepted, the CPU branches to the address set in the corresponding interrupt vector. Figure 1.9.2 shows the interrupt vector. MSB Vector address (L) LSB Low address Mid address Vector address (H) 0000 High address 0000 0000 Figure 1.9.2. Interrupt Vector • Fixed Vector Tables The fixed vector tables are allocated to the addresses from FFFDC16 to FFFFF16. Table 1.9.1 lists the fixed vector tables. In the flash memory version of microcomputer, the vector addresses (H) of fixed vectors are used by the ID code check function. For details, refer to the section "flash memory rewrite disabling function". Table 1.9.1. Fixed Vector Tables Interrupt source Vector table addresses Remarks Reference Address (L) to address (H) Undefined instruction FFFDC16 to FFFDF16 Interrupt on UND instruction M16C/60, M16C/20 Overflow FFFE016 to FFFE316 Interrupt on INTO instruction series software If the contents of address BRK instruction FFFE416 to FFFE716 manual FFFE716 is FF16, program execution starts from the address shown by the vector in the relocatable vector table. Address match FFFE816 to FFFEB16 Address match interrupt Single step (Note) FFFEC16 to FFFEF16 Watchdog timer FFFF016 to FFFF316 Watchdog timer Oscillation stop and re-oscillation detection Clock generating circuit ________ DBC (Note) FFFF416 to FFFF716 (Reserved) FFFF816 to FFFFB16 Reset FFFFC16 to FFFFF16 Reset Note: Do not normally use this interrupt because it is provided exclusively for use by development support tools. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 50 of 201 M16C/6S Group Interrupts • Relocatable Vector Tables The 256 bytes beginning with the start address set in the INTB register comprise a reloacatable vector table area. Table 1.9.2 lists the relocatable vector tables. Setting an even address in the INTB register results in the interrupt sequence being executed faster than in the case of odd addresses. Table 1.9.2. Relocatable Vector Tables Interrupt source BRK instruction (Note 5) Vector address (Note 1) Address (L) to address (H) Software interrupt number +0 to +3 (000016 to 000316) 0 1 to 3 (Reserved) INT3 (Reserved) (Note 4) Timer B4, UART1 bus collision detect (Note 4) Timer B3, UART0 bus collision detect +16 to +19 (001016 to 001316) 4 +20 to +23 (001416 to 001716) 5 +24 to +27 (001816 to 001B16) 6 +28 to +31 (001C16 to 001F16) 7 Reference M16C/60, M16C/20 series software manual INT interrupt Timer Serial I/O SI/O4, INT5 (Note 2) +32 to +35 (002016 to 002316) 8 SI/O3, INT4 (Note 2) +36 to +39 (002416 to 002716) 9 INT interrupt Serial I/O UART 2 bus collision detection +40 to +43 (002816 to 002B16) 10 Serial I/O DMA0 +44 to +47 (002C16 to 002F16) 11 DMA1 +48 to +51 (003016 to 003316) 12 (Reserved) +52 to +55 (003416 to 003716) 13 (Reserved) +56 to +59 (003816 to 003B16) 14 UART2 transmit, NACK2 (Note 3) +60 to +63 (003C16 to 003F16) 15 UART2 receive, ACK2 (Note 3) +64 to +67 (004016 to 004316) 16 UART0 transmit, NACK0 (Note 3) +68 to +71 (004416 to 004716) 17 UART0 receive, ACK0 (Note 3) +72 to +75 (004816 to 004B16) 18 UART1 transmit, NACK1(Note 3) +76 to +79 (004C16 to 004F16) 19 UART1 receive, ACK1 (Note 3) +80 to +83 (005016 to 005316) 20 Timer A0 +84 to +87 (005416 to 005716) 21 Timer A1 +88 to +91 (005816 to 005B16) 22 Timer A2 +92 to +95 (005C16 to 005F16) 23 Timer A3 +96 to +99 (006016 to 006316) 24 Timer A4 +100 to +103 (006416 to 006716) 25 (Reserved) +104 to +107 (006816 to 006B16) 26 (Reserved) +108 to +111 (006C 16 to 006F16) 27 (Reserved) +112 to +115 (0070 16 to 007316) 28 INT0 +116 to +119 (0074 16 to 007716) 29 INT1 +120 to +123 (007816 to 007B16) 30 +124 to +127 (007C16 to 007F16) 31 +128 to +131 (008016 to 008316) 32 to INT2 Software interrupt (Note 5) to +252 to +255 (00FC16 to 00FF16) 63 DMAC Serial I/O Timer INT interrupt M16C/60, M16C/20 series software manual Note 1: Address relative to address in INTB. Note 2: Set the IFSR register's IFSR6 and IFSR7 bits “0”. Note 3: During I2C mode, NACK and ACK interrupts comprise the interrupt source. Note 4: Set the IFSR2A register’s IFSR26 and IFSR27 bits “1”. Note 5: These interrupts cannot be disabled using the I flag. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 51 of 201 M16C/6S Group Interrupts Interrupt Control The following describes how to enable/disable the maskable interrupts, and how to set the priority in which order they are accepted. What is explained here does not apply to nonmaskable interrupts. Use the FLG register’s I flag, IPL, and each interrupt control register’s ILVL2 to ILVL0 bits to enable/disable the maskable interrupts. Whether an interrupt is requested is indicated by the IR bit in each interrupt control register. Figure 1.9.3 shows the interrupt control registers. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 52 of 201 M16C/6S Group Interrupts Interrupt control register (Note 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol U1BCNIC (Note 3) U0BCNIC (Note 3) BCNIC DM0IC, DM1IC S0TIC to S2TIC S0RIC to S2RIC TA0IC to TA4IC Bit symbol ILVL0 Address 0046 16 0047 16 004A16 004B16, 004C16 005116, 005316, 004F16 005216, 005416, 005016 005516 to 005916 Bit name Interrupt priority level select bit ILVL1 ILVL2 IR (b7-b4) Interrupt request bit After reset XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 Function b2 b1 b0 000: 001: 010: 011: 100: 101: 110: 111: Level 0 (interrupt disabled) Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 0 : Interrupt not requested 1 : Interrupt requested RW RW RW RW RW (Note 1) No functions are assigned. When writing to these bits, write “0”. The values in these bits when read are indeterminate. Note 1: This bit can only be reset by writing "0" (Do not write "1"). Note 2: To rewrite the interrupt control registers, do so at a point that does not generate the interrupt request for that register. For details, see the precautions for interrupts. Note 3: Use the IFSR2A register to select. b7 b6 b5 b4 b3 0 b2 b1 b0 Symbol INT3IC S4IC S3IC INT0IC to INT2IC Bit symbol ILVL0 Address 004416 004816 004916 005D16 to 005F16 Bit name Interrupt priority level select bit ILVL1 ILVL2 IR POL Function RW 0 0 0 : Level 0 (interrupt disabled) 0 0 1 : Level 1 0 1 0 : Level 2 0 1 1 : Level 3 1 0 0 : Level 4 1 0 1 : Level 5 1 1 0 : Level 6 1 1 1 : Level 7 RW b2 b1 b0 RW RW Interrupt request bit 0: Interrupt not requested 1: Interrupt requested Polarity select bit 0 : Selects falling edge (Notes 3, 4) 1 : Selects rising edge RW Must always be set to “0” RW Reserved bit (b7-b6) After reset XX00X0002 XX00X0002 XX00X0002 XX00X0002 No functions are assigned. When writing to these bits, write “0”. The values in these bits when read are indeterminate. RW (Note 1) RW Note 1: This bit can only be reset by writing "0" (Do not write "1"). Note 2: To rewrite the interrupt control register, do so at a point that does not generate the interrupt request for that register. For details, see the precautions for interrupts. Note 3: If the IFSR register’s IFSRi bit (i = 0 to 5) is "1" (both edges), set the INTiIC register’s POL bit to "0 "(falling edge). Note 4: Set the S3IC or S4IC register’s POL bit to "0" (falling edge) when the IFSR register’s IFSR6 bit = 0 (SI/O3 selected) or IFSR7 bit = 0 (SI/O4 selected), respectively. Figure 1.9.3. Interrupt Control Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 53 of 201 M16C/6S Group Interrupts I Flag The I flag enables or disables the maskable interrupt. Setting the I flag to “1” (= enabled) enables the maskable interrupt. Setting the I flag to “0” (= disabled) disables all maskable interrupts. IR Bit The IR bit is set to “1” (= interrupt requested) when an interrupt request is generated. Then, when the interrupt request is accepted and the CPU branches to the corresponding interrupt vector, the IR bit is cleared to “0” (= interrupt not requested). The IR bit can be cleared to “0” in a program. Note that do not write “1” to this bit. ILVL2 to ILVL0 Bits and IPL Interrupt priority levels can be set using the ILVL2 to ILVL0 bits. Table 1.9.3 shows the settings of interrupt priority levels and Table 1.9.4 shows the interrupt priority levels enabled by the IPL. The following are conditions under which an interrupt is accepted: · I flag = “1” · IR bit = “1” · interrupt priority level > IPL The I flag, IR bit, ILVL2 to ILVL0 bits and IPL are independent of each other. In no case do they affect one another. Table 1.9.3. Settings of Interrupt Priority Levels ILVL2 to ILVL0 bits Interrupt priority level 0002 Level 0 (interrupt disabled) 0012 Level 1 0102 Priority order Table 1.9.4. Interrupt Priority Levels Enabled by IPL IPL Enabled interrupt priority levels 0002 Interrupt levels 1 and above are enabled 0012 Interrupt levels 2 and above are enabled Level 2 0102 Interrupt levels 3 and above are enabled 0112 Level 3 0112 Interrupt levels 4 and above are enabled 1002 Level 4 1002 Interrupt levels 5 and above are enabled 1012 Level 5 1012 Interrupt levels 6 and above are enabled 1102 Level 6 1102 Interrupt levels 7 and above are enabled 1112 Level 7 1112 All maskable interrupts are disabled Rev.5.01 Dec 10, 2009 REJ03B0014-0501 Low High page 54 of 201 M16C/6S Group Interrupts Interrupt Sequence An interrupt sequence — what are performed over a period from the instant an interrupt is accepted to the instant the interrupt routine is executed — is described here. If an interrupt occurs during execution of an instruction, the processor determines its priority when the execution of the instruction is completed, and transfers control to the interrupt sequence from the next cycle. If an interrupt occurs during execution of either the SMOVB, SMOVF, SSTR or RMPA instruction, the processor temporarily suspends the instruction being executed, and transfers control to the interrupt sequence. The CPU behavior during the interrupt sequence is described below. Figure 1.9.4 shows time required for executing the interrupt sequence. (1) The CPU gets interrupt information (interrupt number and interrupt request priority level) by reading the address 0000016. Then it clears the IR bit for the corresponding interrupt to “0” (interrupt not requested). (2) The FLG register immediately before entering the interrupt sequence is saved to the CPU’s internal temporary register(Note 1). (3) The I, D and U flags in the FLG register become as follows: The I flag is cleared to “0” (interrupts disabled). The D flag is cleared to “0” (single-step interrupt disabled). The U flag is cleared to “0” (ISP selected). However, the U flag does not change state if an INT instruction for software interrupt Nos. 32 to 63 is executed. (4) The CPU’s internal temporary register (Note 1) is saved to the stack. (5) The PC is saved to the stack. (6) The interrupt priority level of the accepted interrupt is set in the IPL. (7) The start address of the relevant interrupt routine set in the interrupt vector is stored in the PC. After the interrupt sequence is completed, the processor resumes executing instructions from the start address of the interrupt routine. Note: This register cannot be used by user. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 CPU clock Address bus Address 000016 Interrupt information Data bus RD Indeterminate Indeterminate SP-2 SP-2 contents SP-4 SP-4 contents vec vec contents vec+2 vec+2 contents Indeterminate WR The indeterminate state depends on the instruction queue buffer. A read cycle occurs when the instruction queue buffer is ready to accept instructions. Figure 1.9.4. Time Required for Executing Interrupt Sequence Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 55 of 201 PC 18 M16C/6S Group Interrupts Interrupt Response Time Figure 1.9.5 shows the interrupt response time. The interrupt response or interrupt acknowledge time denotes a time from when an interrupt request is generated till when the first instruction in the interrupt routine is executed. Specifically, it consists of a time from when an interrupt request is generated till when the instruction then executing is completed ((a) in Figure 1.9.5) and a time during which the interrupt sequence is executed ((b) in Figure 1.9.5). Interrupt request generated Interrupt request acknowledged Time Instruction Interrupt sequence (a) Instruction in interrupt routine (b) Interrupt response time (a) A time from when an interrupt request is generated till when the instruction then executing is completed. The length of this time varies with the instruction being executed. The DIVX instruction requires the longest time, which is equal to 30 cycles (without wait state, the divisor being a register). (b) A time during which the interrupt sequence is executed. For details, see the table below. Note, however, that the values in this table must be increased 2 cycles for the DBC interrupt and 1 cycle for the address match and single-step interrupts. Interrupt vector address SP value 16-Bit bus, without wait 8-Bit bus, without wait Even Even 18 cycles 20 cycles Even Odd 19 cycles 20 cycles Odd Even 19 cycles 20 cycles Odd Odd 20 cycles 20 cycles Figure 1.9.5. Interrupt response time Variation of IPL when Interrupt Request is Accepted When a maskable interrupt request is accepted, the interrupt priority level of the accepted interrupt is set in the IPL. When a software interrupt or special interrupt request is accepted, one of the interrupt priority levels listed in Table 1.9.5 is set in the IPL. Shown in Table 1.9.5 are the IPL values of software and special interrupts when they are accepted. Table 1.9.5. IPL Level That is Set to IPL When A Software or Special Interrupt Is Accepted Interrupt sources Watchdog timer _________ Software, address match, DBC, single-step Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 56 of 201 Level that is set to IPL 7 Not changed M16C/6S Group Interrupts Saving Registers In the interrupt sequence, the FLG register and PC are saved to the stack. At this time, the 4 high-order bits of the PC and the 4 high-order (IPL) and 8 low-order bits of the FLG register, 16 bits in total, are saved to the stack first. Next, the 16 low-order bits of the PC are saved. Figure 1.9.6 shows the stack status before and after an interrupt request is accepted. The other necessary registers must be saved in a program at the beginning of the interrupt routine. Use the PUSHM instruction, and all registers except SP can be saved with a single instruction. Address MSB Stack m–4 m–4 PC m–3 m–3 PC m–2 m–2 FLGL Address MSB Stack L SB L SB [SP] New SP value L M m–1 m–1 m Content of previous stack m+1 Content of previous stack [SP] SPvalue before interrupt occurs Stack status before interrupt request is acknowledged PCH : 4 high-order bits of PC PCM : 8 middle-order bits of PC PCL : 8 low-order bits of PC FLGH PCH m Content of previous stack m+1 Content of previous stack Stack status after interrupt request is acknowledged FLGH : 4 high-order bits of FLG FLGL : 8 low-order bits of FLG Figure 1.9.6. Stack Status Before and After Acceptance of Interrupt Request Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 57 of 201 M16C/6S Group Interrupts The operation of saving registers carried out in the interrupt sequence is dependent on whether the SP(Note), at the time of acceptance of an interrupt request, is even or odd. If the stack pointer (Note) is even, the FLG register and the PC are saved, 16 bits at a time. If odd, they are saved in two steps, 8 bits at a time. Figure 1.9.7 shows the operation of the saving registers. Note: When any INT instruction in software numbers 32 to 63 has been executed, this is the SP indicated by the U flag. Otherwise, it is the ISP. (1) SP contains even number Address Sequence in which order registers are saved Stack [SP] – 5 (Odd) [SP] – 4 (Even) PCL [SP] – 3(Odd) PCM [SP] – 2 (Even) FLGL [SP] – 1(Odd) [SP] FLGH (2) Saved simultaneously, all 16 bits PCH (1) Saved simultaneously, all 16 bits (Even) Finished saving registers in two operations. (2) SP contains odd number Address Stack Sequence in which order registers are saved [SP] – 5 (Even) [SP] – 4(Odd) PCL (3) [SP] – 3 (Even) PCM (4) [SP] – 2(Odd) FLGL [SP] – 1 (Even) [SP] FLGH Saved, 8 bits at a time (1) PCH (2) (Odd) Finished saving registers in four operations. PCH : 4 high-order bits of PC PCM : 8 middle-order bits of PC PCL : 8 low-order bits of PC FLGH : 4 high-order bits of FLG FLGL : 8 low-order bits of FLG Note: [SP] denotes the initial value of the SP when interrupt request is acknowledged. After registers are saved, the SP content is [SP] minus 4. Figure 1.9.7. Operation of Saving Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 58 of 201 M16C/6S Group Interrupts Returning from an Interrupt Routine The FLG register and PC in the state in which they were immediately before entering the interrupt sequence are restored from the stack by executing the REIT instruction at the end of the interrupt routine. Thereafter the CPU returns to the program which was being executed before accepting the interrupt request. Return the other registers saved by a program within the interrupt routine using the POPM or similar instruction before executing the REIT instruction. Interrupt Priority If two or more interrupt requests are generated while executing one instruction, the interrupt request that has the highest priority is accepted. For maskable interrupts (peripheral functions), any desired priority level can be selected using the ILVL2 to ILVL0 bits. However, if two or more maskable interrupts have the same priority level, their interrupt priority is resolved by hardware, with the highest priority interrupt accepted. The watchdog timer and other special interrupts have their priority levels set in hardware. Figure 1.9.8 shows the priorities of hardware interrupts. Software interrupts are not affected by the interrupt priority. If an instruction is executed, control branches invariably to the interrupt routine. ________ Reset > DBC > WDT > Peripheral function > Single step > Address match Figure 1.9.8. Hardware Interrupt Priority Interrupt Priority Resolution Circuit The interrupt priority resolution circuit is used to select the interrupt with the highest priority among those requested. Figure 1.9.9 shows the circuit that judges the interrupt priority level. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 59 of 201 M16C/6S Group Interrupts Priority level of each interrupt Level 0 (initial value) INT1 High Timer A3 Timer A1 UART1 bus collision INT3 INT2 INT0 Timer A4 Timer A2 UART0 bus collision UART1 reception, ACK1 UART0 reception, ACK0 Priority of peripheral function interrupts (if priority levels are same) UART2 reception, ACK2 DMA1 UART 2 bus collision SI/O4 Timer A0 UART1 transmission, NACK1 UART0 transmission, NACK0 UART2 transmission, NACK2 DMA0 Low SI/O3 IPL Interrupt request level resolution output To clock generation circuit (Figure 1.7.1) I flag Interrupt request accepted Address match Watchdog timer Oscillation stop and re-oscillation detection Power supply down detection DBC Figure 1.9.9. Interrupts Priority Select Circuit Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 60 of 201 M16C/6S Group Interrupts ______ INT Interrupt _______ INTi interrupt (i=0 to 3) is triggered by the edges of external inputs. The edge polarity is selected using the IFSR register's IFSRi bit. Figure 1.9.10 shows the IFSR and IFSR2A registers. Interrupt request cause select register b7 b6 0 0 b5 b4 b3 b2 b1 b0 Symbol IFSR Address 035F16 Bit name Bit symbol IFSR0 IFSR1 IFSR2 IFSR3 (b5-b4) After reset 0016 Function RW INT0 interrupt polarity switching bit 0 : One edge 1 : Both edges (Note 1) RW INT1 interrupt polarity switching bit 0 : One edge 1 : Both edges (Note 1) RW INT2 interrupt polarity switching bit 0 : One edge 1 : Both edges (Note 1) RW INT3 interrupt polarity switching bit 0 : One edge 1 : Both edges (Note 1) RW Nothing is assigned. When write, set to “0”. When read, its content is interdeterminate. IFSR6 Interrupt request cause select bit (Note 2) 0 : SI/O3 (Note 3) 1 : reserved RW IFSR7 Interrupt request cause select bit (Note 2) 0 : SI/O4 1 : reserved RW Note 1: When setting this bit to “1” (= both edges), make sure the INT0IC to INT3IC register’s POL bit is set to “0” (= falling edge). Note 2: Set this bit to “0” (= SI/O3, SI/O4) Note 3: When setting this bit to “0” (= SI/O3, SI/O4), make sure the S3IC and S4IC registers’ POL bit is set to “0” (= falling edge). Interrupt request cause select register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol IFSR2A Bit symbol (b5-b0) IFSR26 IFSR27 Address 035E16 Bit name page 61 of 201 Function RW Nothing is assigned. When write, set to “0”. When read, their contents are indeterminate. Interrupt request cause select bit 0 : reserved 1 : UART0 bus collision detection RW Interrupt request cause select bit 0 : reserved 1 : UART1 bus collision detection RW Figure 1.9.10. IFSR Register and IFSR2A Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 After reset 00XXXXXX2 M16C/6S Group Interrupts Address Match Interrupt An address match interrupt is generated immediately before executing the instruction at the address indicated by the RMADi register (i=0 to 3). Set the start address of any instruction in the RMADi register. Use the AIER register’s AIER0 and AIER1 bits and the AIER2 register’s AIER20 and AIER21 bits to enable or disable the interrupt. Note that the address match interrupt is unaffected by the I flag and IPL. For address match interrupts, the value of the PC that is saved to the stack area varies depending on the instruction being executed (refer to Saving Registers). (The value of the PC that is saved to the stack area is not the correct return address.) Therefore, follow one of the methods described below to return from the address match interrupt. • Rewrite the content of the stack and then use the REIT instruction to return. • Restore the stack to its previous state before the interrupt request was accepted by using the POP or similar other instruction and then use a jump instruction to return. Table 1.9.6 shows the value of the PC that is saved to the stack area when an address match interrupt request is accepted. Figure 1.9.11 shows the AIER, AIER2, and RMAD0 to RMAD3 registers. Table 1.9.6. Value of the PC that is saved to the stack area when an address match interrupt request is accepted Instruction at the Address Indicated by the RMADi Register • 16-bit op-code instruction • Instruction shown below among 8-bit operation code instructions ADD.B:S #IMM8,dest SUB.B:S #IMM8,dest AND.B:S #IMM8,dest OR.B:S #IMM8,dest MOV.B:S #IMM8,dest STZ.B:S #IMM8,dest STNZ.B:S #IMM8,dest STZX.B:S #IMM81,#IMM82,dest CMP.B:S #IMM8,dest PUSHM src POPM dest JMPS #IMM8 JSRS #IMM8 MOV.B:S #IMM,dest (However, dest=A0 or A1) Value of the PC that is saved to the stack area The address indicated by the RMADi register +2 The address indicated by the RMADi register +1 Instructions other than the above Value of the PC that is saved to the stack area : Refer to 12.5.7 Saving Registers. Table 1.9.7. Relationship Between Address Match Interrupt Sources and Associated Registers Address match interrupt sources Address match interrupt 0 Address match interrupt 1 Address match interrupt 2 Address match interrupt 3 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 Address match interrupt enable bit AIER0 AIER1 AIER20 AIER21 page 62 of 201 Address match interrupt register RMAD0 RMAD1 RMAD2 RMAD3 M16C/6S Group Interrupts Address match interrupt enable register b7 b6 b5 b4 b3 b2 b1 b0 Symbol AIER Bit symbol Address 000916 After reset XXXXXX002 Function RW AIER0 Address match interrupt 0 enable bit Bit name 0 : Interrupt disabled 1 : Interrupt enabled RW AIER1 Address match interrupt 1 enable bit 0 : Interrupt disabled 1 : Interrupt enabled RW (b7-b2) Nothing is assigned. When write, set to “0”. When read, their contents are indeterminate. Address match interrupt enable register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol AIER2 Address 01BB16 After reset XXXXXX002 Bit symbol Bit name Function RW AIER20 Address match interrupt 2 enable bit 0 : Interrupt disabled 1 : Interrupt enabled RW AIER21 Address match interrupt 3 enable bit 0 : Interrupt disabled 1 : Interrupt enabled RW (b7-b2) Nothing is assigned. When write, set to “0”. When read, their contents are indeterminate. Address match interrupt register i (i = 0 to 3) (b23) b7 (b19) b3 (b16)(b15) b0 b7 (b8) b0 b7 b0 Symbol RMAD0 RMAD1 RMAD2 RMAD3 Address 001216 to 001016 001616 to 001416 01BA16 to 01B816 01BE16 to 01BC16 Function Address setting register for address match interrupt Setting range RW 0000016 to FFFFF16 RW Nothing is assigned. When write, set to “0”. When read, their contents are indeterminate. Figure 1.9.11. AIER Register, AIER2 Register and RMAD0 to RMAD3 Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 63 of 201 After reset X0000016 X0000016 X0000016 X0000016 M16C/6S Group Interrupts Precautions for Interrupts (1) Reading Address 0000016 • Do not read the address 0000016 in a program. When a maskable interrupt request is accepted, the CPU reads interrupt information (interrupt number and interrupt request priority level) from the address 0000016 during the interrupt sequence. At this time, the IR bit for the accepted interrupt is cleared to “0”. If the address 0000016 is read in a program, the IR bit for the interrupt which has the highest priority among the enabled interrupts is cleared to “0”. This causes a problem that the interrupt is canceled, or an unexpected interrupt is generated. (2) SP Setting • Set any value in the SP before accepting an interrupt. The SP is cleared to ‘000016’ after reset. Therefore, if an interrupt is accepted before setting any value in the SP, the program may go out of control. _____ (3) INT Interrupt ________ • Either an “L” level or an “H” level of at least 250 ns width is necessary for the signal input to the INT0 ________ through INT3 pins regardless of the CPU clock. ________ ________ • When the polarity of the INT0 to INT3 pins is changed, the IR bit is sometimes set to “1” (=interrupt requested). After changing the polarity, set the IR bit to “0” (=interrupt not requested). Figure 1.9.12 ______ shows the procedure for changing the INT interrupt generate factor. (4) Watchdog Timer Interrupt • Initialize the watchdog timer after the watchdog timer interrupt occurs. Set the I flag to “0” (=disable interrupt) Set the ILVL2 to ILVL0 bits to '0002' (= level 0) (Disable INT interrupt) Set the POL bit Set the IR bit to “0” (=interrupt not requested) Set the ILVL2 to ILVL0 bits to '0012' (=level 1) to '1112' (=level 7) (Enable the accepting of INT interrupt request) Set the I flag to “1” (= enable interrupt) Note: Execute the setting above individually. Do not execute two or more settings at once (by one instruction). ______ Figure 1.9.12. Switching Procedure for INT Interrupt Request Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 64 of 201 M16C/6S Group Interrupts (5) Modifying Interrupt Control Register • Each interrupt control register can only be modified while no interrupt requests corresponding to that register are generated. If interrupt requests managed by any interrupt control register are likely to occur, disable the interrupts before modifying the register. A sample program is shown below. To modify any interrupt control register after disabling interrupts, be careful with the instructions used. Modifying other than the IR bit If an interrupt request corresponding to that register is generated while executing the instruction, the IR bit may not be set to “1” (= interrupt requested), with the result that the interrupt request is ignored. If this presents a problem, use the following instructions to modify the register. Instructions to use: AND, OR, BCLR, BSET Modifying the IR bit Even when the IR bit is cleared to “0” (= interrupt not requested), it may not actually be cleared to “0” depending on the instruction used. Therefore, use the MOV instruction to clear the IR bit. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 65 of 201 M16C/6S Group Watchdog Timer Watchdog Timer The watchdog timer is the function of detecting when the program is out of control. Therefore, we recommend using the watchdog timer to improve reliability of a system. The watchdog timer contains a 15-bit counter which counts down the clock derived by dividing the CPU clock using the prescaler. Whether to generate a watchdog timer interrupt request or apply a watchdog timer reset as an operation to be performed when the watchdog timer underflows after reaching the terminal count can be selected using the PM12 bit of PM1 register. The PM12 bit can only be set to “1” (reset). Once this bit is set to “1”, it cannot be set to “0” (watchdog timer interrupt) in a program. The pin, CPU and SFR initialized where the monitor timer underflows when the PM12 bit is “1” are the same as in software reset. When the main clock is selected for CPU clock, the divide-by-N value for the prescaler can be chosen to be 16 or 128. The period of watchdog timer can be calculated as given below. The period of watchdog timer is, however, subject to an error due to the prescaler. With main clock chosen for CPU clock Prescaler dividing (16 or 128) X Watchdog timer count (32768) Watchdog timer period = CPU clock For example, when CPU clock = 16 MHz and the divide-by-N value for the prescaler= 16, the watchdog timer period is approx. 32.8 ms. The watchdog timer is initialized by writing to the WDTS register. The prescaler is initialized after reset. Note that the watchdog timer and the prescaler both are inactive after reset, so that the watchdog timer is activated to start counting by writing to the WDTS register. In stop mode and wait mode, the watchdog timer and prescaler are stopped. Counting is resumed from the held value when the modes or state are released. Figure 1.10.1 shows the block diagram of the watchdog timer. Figure 1.10.2 shows the watchdog timerrelated registers. • Count source protective mode In this mode, a On-chip Oscillator clock is used for the watchdog timer count source. The watchdog timer can be kept being clocked even when CPU clock stops as a result of run-away. Before this mode can be used, the following register settings are required: (1) Set the PRC1 bit of PRCR register to “1” (enable writes to PM1 and PM2 registers). (2) Set the PM12 bit of PM1 register to “1” (reset when the watchdog timer underflows). (3) Set the PM22 bit of PM2 register to “1” (On-chip Oscillator clock used for the watchdog timer count source). (4) Set the PRC1 bit of PRCR register to “0” (disable writes to PM1 and PM2 registers). (5) Write to the WDTS register (watchdog timer starts counting). Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 66 of 201 M16C/6S Group Watchdog Timer Setting the PM22 bit to “1” results in the following conditions • The On-chip Oscillator starts oscillating, and the On-chip Oscillator clock becomes the watchdog timer count source. Watchdog timer count (32768) Watchdog timer period = on-chip oscillator clock • The CM10 bit of CM1 register is disabled against write. (Writing a “1” has no effect, nor is stop mode entered.) • The watchdog timer does not stop when in wait mode. Prescaler CM07 = 0 WDC7 = 0 1/16 CPU clock PM12 = 0 1/128 CM07 = 0 WDC7 = 1 PM22 = 0 CM07 = 1 PM22 = 1 Watchdog timer interrupt request HOLD 1/2 Watchdog timer PM12 = 1 Reset On-chip Oscillator clock Set to “7FFF16” Write to WDTS register Internal RESET signal (“L” active) CM07: Bit in CM0 register WDC7: Bit in WDC register PM12: Bit in PM1 register PM22: Bit in PM2 register Figure 1.10.1. Watchdog Timer Block Diagram Watchdog timer control register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol WDC Address After reset 000F16 00XXXXXX2 Bit symbol Bit name High-order bit of watchdog timer (b4-b0) (b6-b5) WDC7 Function RW RO Reserved bit Must set to “0” RW Prescaler select bit 0 : Divided by 16 1 : Divided by 128 RW Watchdog timer start register (Note) b7 b0 Symbol WDTS Address 000E16 After reset Indeterminate Function RW The watchdog timer is initialized and starts counting after a write instruction to WO this register. The watchdog timer value is always initialized to “7FFF16” regardless of whatever value is written. Note : Write to the WDTS register after the watchdog timer interrupt occurs. Figure 1.10.2. WDC Register and WDTS Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 67 of 201 M16C/6S Group DMAC DMAC The DMAC (Direct Memory Access Controller) allows data to be transferred without the CPU intervention. Two DMAC channels are included. Each time a DMA request occurs, the DMAC transfers one (8 or 16-bit) data from the source address to the destination address. The DMAC uses the same data bus as used by the CPU. Because the DMAC has higher priority of bus control than the CPU and because it makes use of a cycle steal method, it can transfer one word (16 bits) or one byte (8 bits) of data within a very short time after a DMA request is generated. Figure 1.11.1 shows the block diagram of the DMAC. Table 1.11.1 shows the DMAC specifications. Figures 1.11.2 to 1.11.4 show the DMAC-related registers. Address bus DMA0 source pointer SAR0(20) (addresses 002216 to 002016) DMA0 destination pointer DAR0 (20) (addresses 002616 to 002416) DMA0 forward address pointer (20) (Note) DMA0 transfer counter reload register TCR0 (16) DMA1 source pointer SAR1 (20) (addresses 003216 to 003016) (addresses 002916, 002816) DMA0 transfer counter TCR0 (16) DMA1 destination pointer DAR1 (20) (addresses 003616 to 003416) DMA1 transfer counter reload register TCR1 (16) DMA1 forward address pointer (20) (Note) (addresses 003916, 003816) DMA1 transfer counter TCR1 (16) Data bus low-order bits Data bus high-order bits DMA latch high-order bits DMA latch low-order bits Note: Pointer is incremented by a DMA request. Figure 1.11.1. DMAC Block Diagram A DMA request is generated by a write to the DMiSL register (i = 0–1)’s DSR bit, as well as by an interrupt request which is generated by any function specified by the DMiSL register’s DMS and DSEL3–DSEL0 bits. However, unlike in the case of interrupt requests, DMA requests are not affected by the I flag and the interrupt control register, so that even when interrupt requests are disabled and no interrupt request can be accepted, DMA requests are always accepted. Furthermore, because the DMAC does not affect interrupts, the interrupt control register’s IR bit does not change state due to a DMA transfer. A data transfer is initiated each time a DMA request is generated when the DMiCON register’s DMAE bit = “1” (DMA enabled). However, if the cycle in which a DMA request is generated is faster than the DMA transfer cycle, the number of transfer requests generated and the number of times data is transferred may not match. For details, refer to “DMA Requests”. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 68 of 201 M16C/6S Group DMAC Table 1.11.1. DMAC Specifications Item No. of channels Transfer memory space Maximum No. of bytes transferred Specification 2 (cycle steal method) • From any address in the 1M bytes space to a fixed address • From a fixed address to any address in the 1M bytes space • From a fixed address to a fixed address 128K bytes (with 16-bit transfers) or 64K bytes (with 8-bit transfers) ________ ________ DMA request factors (Note 1, Note 2) Falling edge of INT0 or INT1 ________ ________ Both edge of INT0 or INT1 Timer A0 to timer A4 interrupt requests UART0 transfer, UART0 reception interrupt requests UART1 transfer, UART1 reception interrupt requests UART2 transfer, UART2 reception interrupt requests SI/O3, SI/O4 interrupt requests Software triggers Channel priority DMA0 > DMA1 (DMA0 takes precedence) Transfer unit 8 bits or 16 bits Transfer address direction forward or fixed (The source and destination addresses cannot both be in the forward direction.) Transfer mode •Single transfer Transfer is completed when the DMAi transfer counter (i = 0–1) underflows after reaching the terminal count. •Repeat transfer When the DMAi transfer counter underflows, it is reloaded with the value of the DMAi transfer counter reload register and a DMA transfer is con tinued with it. DMA interrupt request generation timing When the DMAi transfer counter underflowed DMA startup Data transfer is initiated each time a DMA request is generated when the DMAiCON register’s DMAE bit = “1” (enabled). DMA shutdown •Single transfer •When the DMAE bit is set to “0” (disabled) •After the DMAi transfer counter underflows •Repeat transfer When the DMAE bit is set to “0” (disabled) Reload timing for forward ad- When a data transfer is started after setting the DMAE bit to “1” (en abled), the forward address pointer is reloaded with the value of the dress pointer and transfer SARi or the DARi pointer whichever is specified to be in the forward counter direction and the DMAi transfer counter is reloaded with the value of the DMAi transfer counter reload register. Notes: 1. DMA transfer is not effective to any interrupt. DMA transfer is affected neither by the I flag nor by the interrupt control register. 2. The selectable causes of DMA requests differ with each channel. 3. Make sure that no DMAC-related registers (addresses 002016–003F16) are accessed by the DMAC. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 69 of 201 M16C/6S Group DMAC DMA0 request cause select register b7 b6 b5 b4 b3 b2 b1 b0 Symbol DM0SL Address 03B816 Bit symbol DSEL0 DSEL1 After reset 0016 Function Bit name DMA request cause select bit Refer to note RW DSEL2 RW DSEL3 (b5-b4) DMS RW RW RW Nothing is assigned. When write, set to “0”. When read, its content is “0”. DMA request cause expansion select bit 0: Basic cause of request 1: Extended cause of request RW Software DMA request bit A DMA request is generated by setting this bit to “1” when the DMS bit is “0” (basic cause) and the DSEL3 to DSEL0 bits are “00012” (software trigger). The value of this bit when read is “0” . RW DSR Note: The causes of DMA0 requests can be selected by a combination of DMS bit and DSEL3 to DSEL0 bits in the manner described below. DSEL3 to DSEL0 0 0 0 02 0 0 0 12 0 0 1 02 0 0 1 12 0 1 0 02 0 1 0 12 0 1 1 02 0 1 1 12 1 0 0 02 1 0 0 12 1 0 1 02 1 0 1 12 1 1 0 02 1 1 0 12 1 1 1 02 1 1 1 12 DMS=0(basic cause of request) Falling edge of INT0 pin Software trigger Timer A0 Timer A1 Timer A2 Timer A3 Timer A4 – – – UART0 transmit UART0 receive UART2 transmit UART2 receive – UART1 transmit Figure 1.11.2. DM0SL Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 70 of 201 DMS=1(extended cause of request) – – – – – – Two edges of INT0 pin – – – – – – – – – M16C/6S Group DMAC DMA1 request cause select register b7 b6 b5 b4 b3 b2 b1 Symbol DM1SL b0 Address 03BA16 DSEL1 DSEL2 Function Bit name Bit symbol DSEL0 After reset 0016 DMA request cause select bit RW Refer to note RW RW DSEL3 (b5-b4) DMS RW RW Nothing is assigned. When write, set to “0”. When read, its content is “0”. DMA request cause expansion select bit 0: Basic cause of request 1: Extended cause of request RW Software DMA request bit A DMA request is generated by setting this bit to “1” when the DMS bit is “0” (basic cause) and the DSEL3 to DSEL0 bits are “00012” (software trigger). The value of this bit when read is “0” . RW DSR Note: The causes of DMA1 requests can be selected by a combination of DMS bit and DSEL3 to DSEL0 bits in the manner described below. DSEL3 to DSEL0 0 0 0 02 0 0 0 12 0 0 1 02 0 0 1 12 0 1 0 02 0 1 0 12 0 1 1 02 0 1 1 12 1 0 0 02 1 0 0 12 1 0 1 02 1 0 1 12 1 1 0 02 1 1 0 12 1 1 1 02 1 1 1 12 DMS=0(basic cause of request) Falling edge of INT1 pin Software trigger Timer A0 Timer A1 Timer A2 Timer A3 Timer A4 – – – UART0 transmit UART0 receive/ACK0 UART2 transmit UART2 receive/ACK2 – UART1 receive/ACK1 DMS=1(extended cause of request) – – – – – SI/O3 SI/O4 Two edges of INT1 – – – – – – – – DMAi control register(i=0,1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol DM0CON DM1CON Address 002C16 003C16 Bit symbol After reset 00000X002 00000X002 Bit name Function RW DMBIT Transfer unit bit select bit 0 : 16 bits 1 : 8 bits RW DMASL Repeat transfer mode select bit 0 : Single transfer 1 : Repeat transfer RW DMAS DMA request bit 0 : DMA not requested 1 : DMA requested DMAE DMA enable bit 0 : Disabled 1 : Enabled RW DSD Source address direction select bit (Note 2) 0 : Fixed 1 : Forward RW DAD Destination address 0 : Fixed direction select bit (Note 2) 1 : Forward RW (b7-b6) Nothing is assigned. When write, set to “0”. When read, its content is “0”. RW (Note 1) Note 1: The DMAS bit can be set to “0” by writing “0” in a program (This bit remains unchanged even if “1” is written). Note 2: At least one of the DAD and DSD bits must be “0” (address direction fixed). Figure 1.11.3. DM1SL Register, DM0CON Register, and DM1CON Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 71 of 201 M16C/6S Group DMAC DMAi source pointer (i = 0, 1) (Note) (b23) b7 (b19) b3 (b16)(b15) b0 b7 (b8) b0 b7 b0 Symbol SAR0 SAR1 Address 002216 to 002016 003216 to 003016 Function Set the source address of transfer After reset Indeterminate Indeterminate Setting range RW 0000016 to FFFFF16 RW Nothing is assigned. When write, set “0”. When read, these contents are “0”. Note: If the DSD bit of DMiCON register is “0” (fixed), this register can only be written to when the DMAE bit of DMiCON register is “0” (DMA disabled). If the DSD bit is “1” (forward direction), this register can be written to at any time. If the DSD bit is “1” and the DMAE bit is “1” (DMA enabled), the DMAi forward address pointer can be read from this register. Otherwise, the value written to it can be read. DMAi destination pointer (i = 0, 1)(Note) (b23) b7 (b19) b3 (b16)(b15) b0 b7 (b8) b0 b7 b0 Symbol DAR0 DAR1 Address 002616 to 002416 003616 to 003416 Function Set the destination address of transfer After reset Indeterminate Indeterminate Setting range RW 0000016 to FFFFF16 RW Nothing is assigned. When write, set “0”. When read, these contents are “0”. Note: If the DAD bit of DMiCON register is “0” (fixed), this register can only be written to when the DMAE bit of DMiCON register is “0”(DMA disabled). If the DAD bit is “1” (forward direction), this register can be written to at any time. If the DAD bit is “1” and the DMAE bit is “1” (DMA enabled), the DMAi forward address pointer can be read from this register. Otherwise, the value written to it can be read. DMAi transfer counter (i = 0, 1) (b15) b7 (b8) b0 b7 b0 Symbol TCR0 TCR1 Address 002916, 002816 003916, 003816 Function Set the transfer count minus 1. The written value is stored in the DMAi transfer counter reload register, and when the DMAE bit of DMiCON register is set to “1” (DMA enabled) or the DMAi transfer counter underflows when the DMASL bit of DMiCON register is “1” (repeat transfer), the value of the DMAi transfer counter reload register is transferred to the DMAi transfer counter. When read, the DMAi transfer counter is read. Figure 1.11.4. SAR0, SAR1, DAR0, DAR1, TCR0, and TCR1 Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 72 of 201 After reset Indeterminate Indeterminate Setting range RW 000016 to FFFF16 RW M16C/6S Group DMAC 1. Transfer Cycles The transfer cycle consists of a memory or SFR read (source read) bus cycle and a write (destination write) bus cycle. The number of read and write bus cycles is affected by the source and destination ________ addresses of transfer. Furthermore, the bus cycle itself is extended by a software wait or RDY signal. (a) Effect of Source and Destination Addresses If the transfer unit and data bus both are 16 bits and the source address of transfer begins with an odd address, the source read cycle consists of one more bus cycle than when the source address of transfer begins with an even address. Similarly, if the transfer unit and data bus both are 16 bits and the destination address of transfer begins with an odd address, the destination write cycle consists of one more bus cycle than when the destination address of transfer begins with an even address. (b) Effect of Software Wait For memory or SFR accesses in which one or more software wait states are inserted, the number of bus cycles required for that access increases by an amount equal to software wait states. Figure 1.11.5 shows the example of the cycles for a source read. For convenience, the destination write cycle is shown as one cycle and the source read cycles for the different conditions are shown. In reality, the destination write cycle is subject to the same conditions as the source read cycle, with the transfer cycle changing accordingly. When calculating transfer cycles, take into consideration each condition for the source read and the destination write cycle, respectively. For example, when data is transferred in 16 bit units using an 8-bit bus ((2) in Figure 1.11.5), two source read bus cycles and two destination write bus cycles are required. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 73 of 201 M16C/6S Group DMAC (1) When the transfer unit is 8 or 16 bits and the source of transfer is an even address BCLK Address bus CPU use Dummy cycle Destination Source CPU use RD signal WR signal Data bus CPU use Dummy cycle Destination Source CPU use (2) When the transfer unit is 16 bits and the source address of transfer is an odd address BCLK Address bus CPU use Source Source + 1 Destination Dummy cycle CPU use RD signal WR signal Data bus CPU use Source + 1 Source Destination Dummy cycle CPU use (3) When the source read cycle under condition (1) has one wait state inserted BCLK Address bus Destination Source CPU use Dummy cycle CPU use RD signal WR signal Data bus CPU use Source Destination Dummy cycle CPU use (4) When the source read cycle under condition (2) has one wait state inserted BCLK Address bus CPU use Source Source + 1 Destination Dummy cycle CPU use RD signal WR signal Data bus CPU use Source Source + 1 Destination Dummy cycle CPU use Note: The same timing changes occur with the respective conditions at the destination as at the source. Figure 1.11.5. Transfer Cycles for Source Read Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 74 of 201 M16C/6S Group DMAC 2. DMA Transfer Cycles Any combination of even or odd transfer read and write addresses is possible. Table 1.11.2 shows the number of DMA transfer cycles. Table 1.11.3 shows the Coefficient j, k. The number of DMAC transfer cycles can be calculated as follows: No. of transfer cycles per transfer unit = No. of read cycles x j + No. of write cycles x k Table 1.11.2. DMA Transfer Cycles Transfer unit Access address 8-bit transfers (DMBIT= “1”) 16-bit transfers (DMBIT= “0”) Even Odd Even Odd Table 1.11.3. Coefficient j, k Internal ROM, RAM SFR No wait With wait 1-wait2 2-wait2 j 1 2 2 3 k 1 2 2 3 Notes: 1. Depends on the set value of CSE register 2. Depends on the set value of PM20 bit in P Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 75 of 201 No. of read cycles 1 1 1 2 No. of write cycles 1 1 1 2 M16C/6S Group DMAC 3. DMA Enable When a data transfer starts after setting the DMAE bit in DMiCON register (i = 0, 1) to “1” (enabled), the DMAC operates as follows: (1) Reload the forward address pointer with the SARi register value when the DSD bit in DMiCON register is “1” (forward) or the DARi register value when the DAD bit of DMiCON register is “1” (forward). (2) Reload the DMAi transfer counter with the DMAi transfer counter reload register value. If the DMAE bit is set to “1” again while it remains set, the DMAC performs the above operation. However, if a DMA request may occur simultaneously when the DMAE bit is being written, follow the steps below. Step 1: Write “1” to the DMAE bit and DMAS bit in DMiCON register simultaneously. Step 2: Make sure that the DMAi is in an initial state as described above (1) and (2) in a program. If the DMAi is not in an initial state, the above steps should be repeated. 4. DMA Request The DMAC can generate a DMA request as triggered by the cause of request that is selected with the DMS and DSEL3 to DSEL0 bits of DMiSL register (i = 0, 1) on either channel. Table 1.11.4 shows the timing at which the DMAS bit changes state. Whenever a DMA request is generated, the DMAS bit is set to “1” (DMA requested) regardless of whether or not the DMAE bit is set. If the DMAE bit was set to “1” (enabled) when this occurred, the DMAS bit is set to “0” (DMA not requested) immediately before a data transfer starts. This bit cannot be set to “1” in a program (it can only be set to “0”). The DMAS bit may be set to “1” when the DMS or the DSEL3 to DSEL0 bits change state. Therefore, always be sure to set the DMAS bit to “0” after changing the DMS or the DSEL3 to DSEL0 bits. Because if the DMAE bit is “1”, a data transfer starts immediately after a DMA request is generated, the DMAS bit in almost all cases is “0” when read in a program. Read the DMAE bit to determine whether the DMAC is enabled. Table 1.11.4. Timing at Which the DMAS Bit Changes State DMAS bit of the DMiCON register DMA factor Timing at which the bit is set to “1” Timing at which the bit is set to “0” Software trigger When the DSR bit of DMiCON register is set to “1” Peripheral function When the interrupt control register for the peripheral function that is selected by the DSEL3 to DSEL0 and DMS bits of DMiCON register has its IR bit set to “1” Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 76 of 201 • Immediately before a data transfer starts • When set by writing “0” in a program M16C/6S Group DMAC Channel Priority and DMA Transfer Timing If both DMA0 and DMA1 are enabled and DMA transfer request signals from DMA0 and DMA1 are detected active in the same sampling period (one period from a falling edge to the next falling edge of BCLK), the DMAS bit on each channel is set to “1” (DMA requested) at the same time. In this case, the DMA requests are arbitrated according to the channel priority, DMA0 > DMA1. The following describes DMAC operation when DMA0 and DMA1 requests are detected active in the same sampling period. Figure 1.11.6 shows an example of DMA transfer effected by external factors. In Figure 1.11.6, because DMA0 and DMA1 requests occurred at the same time, DMA0 which has higher channel priority is accepted first and a DMA transfer on it starts. When DMA0 finishes one transfer unit, it relinquishes control of the bus to the CPU, and when the CPU finishes one bus access, DMA1 starts a transfer next and after completion of one transfer unit, returns control of the bus to the CPU. Note that because there is only one DMAS bit on each channel, the number of times DMA is requested cannot be counted. Therefore, even if multiple DMA requests occurred before gaining control of the bus as in the case of DMA1 in Figure 1.11.6, the DMAS bit is set to “0” when control of the bus is gained and after completion of one transfer unit, control of the bus is returned to the CPU. An example where DMA requests for external causes are detected active at the same BCLK DMA0 DMA1 CPU INT0 Obtainment of the bus right DMA0 request bit INT1 DMA1 request bit Figure 1.11.6. DMA Transfer by External Factors Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 77 of 201 M16C/6S Group Timers Timers Five 16-bit timers, each capable of operating independently of the others. The count source for each timer acts as a clock, to control such timer operations as counting, reloading, etc. Figures 1.12.1 show block diagrams of timer A. f2 PCLK0 bit = 0 1/2 f1 or f2 f1 • Main clock • On-chip oscillator clock PCLK0 bit = 1 1/8 f8 1/4 f32 f1 or f2 f8 f32 fC32 00 01 10 11 00: Timer mode 10: One-shot timer mode 11: PWM mode TCK1 to TCK0 TMOD1 to TMOD0 10 Timer A0 Noise filter TA0IN 00 Timer A0 interrupt 01: Event counter mode 11 TA0TGH to TA0TGL TCK1 to TCK0 00 01 10 11 Noise filter TA1IN 00: Timer mode 10: One-shot tiemr mode 11: PWM mode TMOD1 to TMOD0 10 Timer A1 interrupt Timer A1 00 01: Event counter mode 11 TA1TGH to TA1TGL TCK1 to TCK0 00 01 10 11 Noise filter TA2IN 00: Timer mode 10: One-shot timer mode 11: PWM mode Noise filter TA3IN Timer A2 interrupt Timer A2 00 11 TCK1 to TCK0 00 01 10 11 TMOD1 to TMOD0 10 01: Event counter mode TA2TGH to TA2TGL 00: Timer mode 10: One-shot timer mode 11: PWM mode TMOD1 to TMOD0 10 Timer A3 interrupt Timer A3 00 01: Event counter mode 11 TA3TGH to TA3TGL 00 01 10 11 TCK1 to TCK0 00: Timer mode 10: One-shot timer mode 11: PWM mode TMOD1 to TMOD0 10 Timer A4 interrupt Timer A4 Noise filter TA4IN 00 01: Event counter mode 11 TA4TGH to TA4TGL TCK1 to TCK0, TMOD1 to TMOD0 : Bits in TAiMR register (i=0 to 4) TAiGH to TAiGL: Bits in ONSF register and TRGSR register NOTES : 1. Be aware that TA0IN shares the pin with RXD2. Figure 1.12.1. Timer A Configuration Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 78 of 201 M16C/6S Group Timer A Timer A Figure 1.12.2 shows a block diagram of the timer A. Figures 1.12.3 to 1.12.5 show registers related to the timer A. The timer A supports the following four modes. Except in event counter mode, timers A0 to A4 all have the same function. Use the TMOD1 to TMOD0 bits of TAiMR register (i = 0 to 4) to select the desired mode. • Timer mode: The timer counts an internal count source. • Event counter mode: The timer counts pulses from an external device or overflows and underflows of other timers. • One-shot timer mode: The timer outputs a pulse only once before it reaches the minimum count “000016.” • Pulse width modulation (PWM) mode: The timer outputs pulses in a given width successively. Select clock High-Order Bits of Data Bus Select Count Source • Timer :TMOD1 to TMOD0=00, MR2=0 • One-Shot Timer :TMOD1 to TMOD0=10 • Pulse Width Modulation:TMOD1 to TMOD0=11 TMOD1 to TMOD0, MR2 f1 or f2 00 f8 01 Low-Order Bits of Data Bus 8 low-order bits • Timer(gate function):TMOD1 to TMOD0=00, MR2=1 f32 10 8 highorder bits Reload Register TCK1 to TCK0 • Event counter:TMOD1 to TMOD0=01 Counter Increment / decrement Always decrement except in event counter mode Polarity Selector TAiIN TAiS 00 10 TAj Overflow (1) TAk Overflow (1) To external trigger circuit 11 TAiTGH to TAiTGL TAiUD Decrement 00 01 11 01 TMOD1 to TMOD0 0 1 Pulse Output MR2 TAiOUT Toggle Flip Flop TAi Timer A0 Timer A1 Timer A2 Timer A3 Timer A4 i=0 to 4 j=i-1, except j=4 if i=0 k=i+1, except k=0 if i=4 NOTES: 1. Overflow or underflow Addresses 0387h - 0386h 0389h - 0388h 038Bh - 038Ah 038Dh - 038Ch 038Fh - 038Eh TAj Timer A4 Timer A0 Timer A1 Timer A2 Timer A3 TAk Timer A1 Timer A2 Timer A3 Timer A4 Timer A0 TCK1 to TCK0, TMOD1 to TMOC0, MR2 to MR1 : Bits in TAiMR register TAiTGH to TAiTGL : Bits in ONSF register if i=0 or bits in TRGSR register if i=1 to 4 TAiS : Bits in the TABSR register TAiUD : Bits in the UDF register Figure 1.12.2. Timer A Block Diagram Timer Ai mode register (i=0 to 4) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TA0MR to TA4MR Bit symbol TMOD0 Address 039616 to 039A16 Bit name Operation mode select bit TMOD1 MR0 MR1 After reset 0016 Function 0 0 : Timer mode 0 1 : Event counter mode 1 0 : One-shot timer mode 1 1 : Pulse width modulation (PWM) mode RW Function varies with each operation mode RW Function varies with each operation mode RW MR2 MR3 TCK0 Count source select bit TCK1 Figure 1.12.3. TA0MR to TA4MR Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 79 of 201 RW b1 b0 RW RW RW RW RW M16C/6S Group Timer A Timer Ai register (i= 0 to 4) (Note 1) (b15) b7 (b8) b0 b7 b0 Symbol TA0 TA1 TA2 TA3 TA4 Address 038716, 038616 038916, 038816 038B16, 038A16 038D16, 038C16 038F16, 038E16 After reset Indeterminate Indeterminate Indeterminate Indeterminate Indeterminate Setting range RW Timer mode Event counter mode Divide the count source by n + 1 where n = set value 000016 to FFFF16 RW Divide the count source by FFFF16 – n + 1 where n = set value when counting up or by n + 1 when counting down (Note 5) 000016 to FFFF16 One-shot timer mode Divide the count source by n where n = set value and cause the timer to stop 000016 to FFFF16 (Notes 2, 4) Mode Function Pulse width Modify the pulse width as follows: modulation PWM period: (216 – 1) / fj High level PWM pulse width: n / fj mode (16-bit PWM) where n = set value, fj = count source frequency Pulse width Modify the pulse width as follows: modulation PWM period: (28 – 1) x (m + 1)/ fj mode High level PWM pulse width: (m + 1)n / fj (8-bit PWM) where n = high-order address set value, m = low-order address set value, fj = count source frequency RW WO 000016 to FFFE16 (Note 3, 4) WO 0016 to FE16 (High-order address) 0016 to FF16 (Low-order address) WO (Note 3, 4) Note 1: The register must be accessed in 16 bit units. Note 2: If the TAi register is set to ‘0000 16,’ the counter does not work and timer Ai interrupt requests are not generated either. Furthermore, if “pulse output” is selected, no pulses are output from the TAiOUT pin. Note 3: If the TAi register is set to ‘0000 16,’ the pulse width modulator does not work, the output level on the TAiOUT pin remains low, and timer Ai interrupt requests are not generated either. The same applies when the 8 high-order bits of the timer TAi register are set to ‘001 6’ while operating as an 8-bit pulse width modulator. Note 4: Use the MOV instruction to write to the TAi register. Note 5: The timer counts pulses from an external device or overflows or underflows in other timers. Count start flag b7 b6 b5 b4 b3 b2 b1 b0 Symbol TABSR Bit symbol Address 038016 After reset 0016 Bit name Function RW RW TA0S Timer A0 count start flag TA1S Timer A1 count start flag TA2S Timer A2 count start flag RW TA3S Timer A3 count start flag RW TA4S Timer A4 count start flag RW (b7-b5) 0 : Stops counting 1 : Starts counting RW Nothing is assigned. When write, set to “0”. When read, its content is indeterminate. Up/down flag (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol UDF Bit symbol Address 038416 Bit name TA0UD Timer A0 up/down flag TA1UD Timer A1 up/down flag TA2UD Timer A2 up/down flag TA3UD Timer A3 up/down flag TA4UD Timer A4 up/down flag TA2P TA3P TA4P After reset 0016 Function 0 : Down count 1 : Up count Enabled by setting the TAiMR register’s MR2 bit to “0” (= switching source in UDF register) during event counter mode. RW RW RW RW RW RW Timer A2 two-phase pulse 0 : two-phase pulse signal WO processing disabled signal processing select bit 1 : two-phase pulse signal processing enabled Timer A3 two-phase pulse WO (Notes 2, 3) signal processing select bit Timer A4 two-phase pulse signal processing select bit WO Note 1: Use MOV instruction to write to this register. Note 2: Make sure the port direction bits for the TA2 IN to TA4IN and TA2 OUT to TA4 OUT pins are set to “0” (input mode). Note 3: When not using the two-phase pulse signal processing function, set the corresponding bit to “0” (TA2P and TA3P must be set “0”). Figure 1.12.4. TA0 to TA4 Registers, TABSR Register, and UDF Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 80 of 201 M16C/6S Group Timer A One-shot start flag b7 b6 b5 b4 b3 b2 b1 Symbol ONSF b0 Address 038216 After reset 0016 0 Bit symbol Bit name Function RW TA0OS Timer A0 one-shot start flag RW TA1OS Timer A1 one-shot start flag The timer starts counting by setting this bit to “1” while the TMOD1 to TMOD0 bits of TAiMR register (i = 0 to 4) = ‘102’ (= one-shot timer mode) and the MR2 bit of TAiMR register = “0” (=TAiOS bit enabled). When read, its content is “0”. Should be set to “0”. RW TA2OS Timer A2 one-shot start flag TA3OS Timer A3 one-shot start flag TA4OS Timer A4 one-shot start flag (b6) TA0TGL Reserved bit Timer A0 event/trigger select bit TA0TGH RW RW RW RW b7 b6 RW 0 0 : Input on TA0 IN is selected (Note 1) 0 1 : TB2 overflow is selected (Note 2) 1 0 : TA4 overflow is selected (Note 2) RW 1 1 : TA1 overflow is selected (Note 2) Note 1: Make sure the PD7_1 bit of PD7 register is set to “0” (= input mode). Note 2: Overflow or underflow Trigger select register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRGSR Bit symbol TA1TGL Address 038316 Bit name Timer A1 event/trigger select bit TA1TGH After reset 0016 Function RW b1 b0 0 0 : Input on TA1 IN is selected (Note 1) RW 1 0 : TA0 overflow is selected (Note 2) 1 1 : TA2 overflow is selected (Note 2) RW (Note 3) TA2TGL Timer A2 event/trigger select bit b3 b2 1 0 : TA1 overflow is selected (Note 2) RW 1 1 : TA3 overflow is selected (Note 2) TA2TGH TA3TGL (Note 3) Timer A3 event/trigger select bit TA3TGH TA4TGL TA4TGH Timer A4 event/trigger select bit b5 b4 1 0 : TA2 overflow is selected (Note 2) RW 1 1 : TA4 overflow is selected (Note 2) (Note 3) RW b7 b6 0 0 : Input on TA4 IN is selected (Note 1) RW 1 0 : TA3 overflow is selected (Note 2) 1 1 : TA0 overflow is selected (Note 2) RW (Note 3) Note 1: Make sure the port direction bits for the TA1 IN to TA4 IN pins are set to “0” (= input mode). Note 2: Overflow or underflow Note 3: Do not set cases which are not discribed. Figure 1.12.5. ONSF Register, TRGSR Register, and CPSRF Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 81 of 201 RW M16C/6S Group Timer A 1. Timer Mode In timer mode, the timer counts a count source generated internally (see Table 1.12.1). Figure 1.12.6 shows TAiMR register in timer mode. Table 1.12.1. Specifications in Timer Mode Item Count source Count operation Specification f1, f2, f8, f32 • Down-count • When the timer underflows, it reloads the reload register contents and continues counting 1/(n+1) n: set value of TAiMR register (i= 0 to 4) 000016 to FFFF16 Set TAiS bit of TABSR register to “1” (= start counting) Set TAiS bit to “0” (= stop counting) Timer underflow I/O port or gate input i≠2, 3 I/O port or pulse output Count value can be read by reading TAi register • When not counting and until the 1st count source is input after counting start Value written to TAi register is written to both reload register and counter • When counting (after 1st count source input) Value written to TAi register is written to only reload register (Transferred to counter when reloaded next) • Gate function Counting can be started and stopped by an input signal to TAiIN pin • Pulse output function Whenever the timer underflows, the output polarity of TAiOUT pin is inverted. When not counting, the pin outputs a low. Divide ratio Count start condition Count stop condition Interrupt request generation timing TAiIN pin function TAiOUT pin function Read from timer Write to timer Select function Timer Ai mode register (i=0 to 4) b7 b6 b5 b4 0 b3 b2 b1 b0 0 0 Symbol TA0MR to TA4MR Bit symbol TMOD0 TMOD1 MR0 MR1 Address 039616 to 039A16 Bit name Operation mode select bit TCK0 Function b1 b0 0 0 : Timer mode Pulse output function select bit 0 : Pulse is not output (TA iOUT pin is a normal port pin) 1 : Pulse is output (Note 1) (TA iOUT pin is a pulse output pin) Gate function select bit b4 b3 MR2 MR3 After reset 0016 0 0 : Gate function not available } (TAi IN pin functions as I/O port) 01: 1 0 : Counts while input on the TAi IN pin is low (Note 2) 1 1 : Counts while input on the TAi IN pin is high (Note 2) Must be set to “0” in timer mode Count source select bit TCK1 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 82 of 201 RW RW RW RW RW b7 b6 0 0 : f1 or f2 0 1 : f8 1 0 : f32 1 1 : Do not set Note 1: TA0 OUT pin is N-channel open drain output. Note 2: The port direction bit for the TAi IN pin must be set to “0” (= input mode). There are not TA2IN and TA3IN. Figure 1.12.6. Timer Ai Mode Register in Timer Mode RW RW RW RW M16C/6S Group Timer A 2. Event Counter Mode In event counter mode, the timer counts pulses from an external device or overflows and underflows of other timers. Timer A4 can count two-phase external signals. Table 1.12.2 lists specifications in event counter mode (when not processing two-phase pulse signal). Table 1.12.3 lists specifications in event counter mode (when processing two-phase pulse signal with the timer A4). Figure 1.12.7 shows TAiMR register in event counter mode (when not processing two-phase pulse signal). Figure 1.12.8 shows TA4MR registers in event counter mode (when processing two-phase pulse signal with the timer A4). Table 1.12.2. Specifications in Event Counter Mode (when not processing two-phase pulse signal) Item Specification Count source • External signals input to TAiIN pin (i=0 to 4) (effective edge can be selected in program) timer Aj (j=i-1, except j=4 if i=0) overflows or underflows, timer Ak (k=i+1, except k=0 if i=4) overflows or underflows Count operation • Up-count or down-count can be selected by external signal or program • When the timer overflows or underflows, it reloads the reload register contents and continues counting. When operating in free-running mode, the timer continues counting without reloading. Divided ratio 1/ (FFFF16 - n + 1) for up-count 1/ (n + 1) for down-count n : set value of TAi register 000016 to FFFF16 Count start condition Set TAiS bit of TABSR register to “1” (= start counting) Count stop condition Set TAiS bit to “0” (= stop counting) Interrupt request generation timing Timer overflow or underflow TAiIN pin function I/O port or count source input i≠2, 3 TAiOUT pin function I/O port, pulse output, or up/down-count select input Read from timer Count value can be read by reading TAi register Write to timer • When not counting and until the 1st count source is input after counting start Value written to TAi register is written to both reload register and counter • When counting (after 1st count source input) Value written to TAi register is written to only reload register (Transferred to counter when reloaded next) Select function • Free-run count function Even when the timer overflows or underflows, the reload register content is not reloaded to it • Pulse output function Whenever the timer underflows or underflows, the output polarity of TAiOUT pin is inverted . When not counting, the pin outputs a low. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 83 of 201 M16C/6S Group Timer A Timer Ai mode register (i=0 to 4) (When not using two-phase pulse signal processing) b7 b6 b5 b4 b3 b2 0 b1 b0 Symbol TA0MR to TA4MR 0 1 Address 039616 to 039A16 Bit symbol Bit name TMOD0 Operation mode select bit Function b1 b0 0 1 : Event counter mode (Note 1) TMOD1 MR0 After reset 0016 Pulse output function select bit 0 : Pulse is not output (TAiOUT pin functions as I/O port) 1 : Pulse is output (Note 2) RW R W RW RW RW (TAiOUT pin functions as pulse output pin) MR1 Count polarity select bit (Note 3) 0 : Counts external signal's falling edge RW 1 : Counts external signal's rising edge MR2 Up/down switching cause select bit 0 : UDF register 1 : Input signal to TAiOUT pin (Note 4) MR3 Must be set to “0” in event counter mode RW TCK0 Count operation type select bit RW TCK1 Can be “0” or “1” when not using two-phase pulse signal processing 0 : Reload type 1 : Free-run type RW RW Note 1: During event counter mode, the count source can be selected using the ONSF and TRGSR registers. Note 2: TA0OUT pin is N-channel open drain output. Note 3: Effective when the TAiGH and TAiGL bits of ONSF or TRGSR register are ‘002’ (TAiIN pin input). Note 4: Count down when input on TAiOUT pin is low or count up when input on that pin is high. The port direction bit for TAiOUT pin must be set to “0” (= input mode). Figure 1.12.7. TAiMR Register in Event Counter Mode (when not using two-phase pulse signal processing) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 84 of 201 M16C/6S Group Timer A Table 1.12.3. Specifications in Event Counter Mode (when processing two-phase pulse signal with timer A4) Item Specification Count source • Two-phase pulse signals input to TAiIN or TAiOUT pins (i = 4) Count operation • Up-count or down-count can be selected by two-phase pulse signal • When the timer overflows or underflows, it reloads the reload register contents and continues counting. When operating in free-running mode, the timer continues counting without reloading. Divide ratio 1/ (FFFF16 - n + 1) for up-count 1/ (n + 1) for down-count n : set value of TAi register 000016 to FFFF16 Count start condition Set TAiS bit of TABSR register to “1” (= start counting) Count stop condition Set TAiS bit to “0” (= stop counting) Interrupt request generation timing Timer overflow or underflow TAiIN pin function Two-phase pulse input TAiOUT pin function Two-phase pulse input Read from timer Count value can be read by reading timer A4 register Write to timer • When not counting and until the 1st count source is input after counting start Value written to TAi register is written to both reload register and counter • When counting (after 1st count source input) Value written to TAi register is written to reload register (Transferred to counter when reloaded next) Select function • Multiply-by-4 processing operation (timer A4) If the phase relationship is such that TAkIN(k=4) pin goes “H” when the input signal on TAkOUT pin is “H”, the timer counts up rising and falling edges on TAkOUT and TAkIN pins. If the phase relationship is such that TAkIN pin goes “L” when the input signal on TAkOUT pin is “H”, the timer counts down rising and falling edges on TAkOUT and TAkIN pins. TAkOUT Count up all edges Count down all edges TAkIN (k=3,4) Count up all edges Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 85 of 201 Count down all edges M16C/6S Group Timer A Timer Ai Mode Register (i=4) (When Using Two-Phase Pulse Signal Processing) b7 b6 b5 b4 b3 b2 b1 b0 0 1 0 0 0 1 Symbol TA4MR Bit Symbol TMOD0 Address 039Ah Function RW 0 1 : Event counter mode RW RW Bit Name Operation Mode Select Bit TMOD1 MR0 After Reset 00h b1 b0 To use two-phase pulse signal processing, set this bit to “0”. RW To use two-phase pulse signal processing, set this bit to “0”. RW MR2 To use two-phase pulse signal processing, set this bit to “1”. RW MR3 To use two-phase pulse signal processing, set this bit to “0”. RW TCK0 Count Operation Type Select Bit 0 : Reload type 1 : Free-run type RW TCK1 Two-Phase Pulse Signal Processing Operation Select Bit (1, 2) 0 : Normal processing operation 1 : Multiply-by-4 processing operation RW MR1 NOTES: 1. No matter how this bit is set, timer A4 always operates in x4 processing mode. 2. If two-phase pulse signal processing is desired, following register settings are required: • Set the TAiP bit in the UDF register to “1” (two-phase pulse signal processing function enabled). • Set the TAiTGH and TAiTGL bits in the TRGSR register to “00b” (TAiIN pin input). • Set the port direction bits for TAiIN and TAiOUT to “0” (input mode). Figure 1.12.8. TA4MR Registers in Event Counter Mode (when using two-phase pulse signal processing with timer A4) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 86 of 201 M16C/6S Group Timer A 3. One-shot Timer Mode In one-shot timer mode, the timer is activated only once by one trigger. (See Table 1.12.4.) When the trigger occurs, the timer starts up and continues operating for a given period. Figure 1.12.9 shows the TAiMR register in one-shot timer mode. Table 1.12.4. Specifications in One-shot Timer Mode Item Count source Count operation Specification Divide ratio Count start condition Count stop condition Interrupt request generation timing TAiIN pin function TAiOUT pin function Read from timer Write to timer Select function Rev.5.01 Dec 10, 2009 REJ03B0014-0501 f1, f2, f8, f32 • Down-count • When the counter reaches 000016, it stops counting after reloading a new value • If a trigger occurs when counting, the timer reloads a new count and restarts counting 1/n n : set value of TAi register 000016 to FFFF16 However, the counter does not work if the divide-by-n value is set to 000016. TAiS bit of TABSR register = “1” (start counting) and one of the following triggers occurs. • External trigger input from the TAiIN pin • timer Aj (j=i-1, except j=4 if i=0) overflow or underflow, timer Ak (k=i+1, except k=0 if i=4) overflow or underflow • The TAiOS bit of ONSF register is set to “1” (= timer starts) • When the counter is reloaded after reaching “000016” • TAiS bit is set to “0” (= stop counting) When the counter reaches “000016” I/O port or trigger input I/O port or pulse output An indeterminate value is read by reading TAi register • When not counting and until the 1st count source is input after counting start Value written to TAi register is written to both reload register and counter • When counting (after 1st count source input) Value written to TAi register is written to only reload register (Transferred to counter when reloaded next) • Pulse output function The timer outputs a low when not counting and a high when counting. page 87 of 201 M16C/6S Group Timer A Timer Ai mode register (i=0 to 4) b7 b6 b5 b4 b3 b2 b1 0 b0 1 0 Symbol TA0MR to TA4MR Bit symbol TMOD0 Address 39616 to 039A16 After reset 0016 Bit name Function RW Operation mode select bit MR0 Pulse output function select bit 0 : Pulse is not output (TA iOUT pin functions as I/O port) RW 1 : Pulse is output (Note 1) (TAi OUT pin functions as a pulse output pin) MR1 External trigger select bit (Note 2) 0 : Falling edge of input signal to TAi IN pin (Note 3) 1 : Rising edge of input signal to TAi IN pin (Note 3) RW MR2 Trigger select bit 0 : TAiOS bit is enabled 1 : Selected by TAiTGH to TAiTGL bits TMOD1 1 0 : One-shot timer mode MR3 Must be set to “0” in one-shot timer mode TCK0 Count source select bit TCK1 b7 b6 0 0 : f1 or f2 0 1 : f8 1 0 : f32 1 1 : Do not set Note 1: TA0 OUT pin is N-channel open drain output. Note 2: Effective when the TAiGH and TAiGL bits of ONSF or TRGSR register are ‘00 2’ (TAi IN pin input). Note 3: The port direction bit for the TAi IN pin must be set to “0” (= input mode). There are not TA2IN and TA3IN. Figure 1.12.9. TAiMR Register in One-shot Timer Mode Rev.5.01 Dec 10, 2009 REJ03B0014-0501 RW b1 b0 page 88 of 201 RW RW RW RW RW M16C/6S Group Timer A 4. Pulse Width Modulation (PWM) Mode In PWM mode, the timer outputs pulses of a given width in succession (see Table 1.12.5). The counter functions as either 16-bit pulse width modulator or 8-bit pulse width modulator. Figure 1.12.10 shows TAiMR register in pulse width modulation mode. Figures 1.12.11 and 1.12.12 show examples of how a 16-bit pulse width modulator operates and how an 8-bit pulse width modulator operates. Table 1.12.5. Specifications in PWM Mode Item Specification Count source Count operation 16-bit PWM 8-bit PWM Count start condition Count stop condition Interrupt request generation timing TAiIN pin function TAiOUT pin function Read from timer Write to timer Rev.5.01 Dec 10, 2009 REJ03B0014-0501 f1, f2, f8, f32 • Down-count (operating as an 8-bit or a 16-bit pulse width modulator) • The timer reloads a new value at a rising edge of PWM pulse and continues counting • The timer is not affected by a trigger that occurs during counting • High level width n / fj n : set value of TAi register (i=o to 4) • Cycle time (216-1) / fj fixed fj: count source frequency (f1, f2, f8, f32) • High level width n x (m+1) / fj n : set value of TAiMR register high-order address • Cycle time (28-1) x (m+1) / fj m : set value of TAiMR register low-order address • TAiS bit of TABSR register is set to “1” (= start counting) • The TAiS bit = 1 and external trigger input from the TAiIN pin • The TAiS bit = 1 and one of the following external triggers occurs Timer Aj (j=i-1, except j=4 if i=0) overflow or underflow, Timer Ak (k=i+1, except k=0 if i=4) overflow or underflow TAiS bit is set to “0” (= stop counting) PWM pulse goes “L” I/O port or trigger input Pulse output An indeterminate value is read by reading TAi register • When not counting and until the 1st count source is input after counting start Value written to TAi register is written to both reload register and counter • When counting (after 1st count source input) Value written to TAi register is written to only reload register (Transferred to counter when reloaded next) page 89 of 201 M16C/6S Group Timer A Timer Ai mode register (i= 0 to 4) b7 b6 b5 b4 b3 b2 b1 b0 1 1 1 Symbol TA0MR to TA4MR Bit symbol TMOD0 TMOD1 Address 039616 to 039A16 After reset 0016 Bit name Operation mode select bit RW Function RW b1 b0 1 1 : PWM mode (Note 1) RW RW MR0 Must be set to “1” in PWM mode MR1 External trigger select bit (Note 2) 0: Falling edge of input signal to TAi IN pin(Note 3) RW 1: Rising edge of input signal to TAi IN pin(Note 3) MR2 Trigger select bit 0 : TAiOS bit is enabled 1 : Selected by TAiTGH to TAiTGL bits RW MR3 16/8-bit PWM mode select bit 0: Functions as a 16-bit pulse width modulator 1: Functions as an 8-bit pulse width modulator RW TCK0 Count source select bit 0 0 : f1 or f2 0 1 : f8 1 0 : f32 1 1 : Do not set b7 b6 TCK1 RW RW Note 1: TA0 OUT pin is N-channel open drain output. Note 2: Effective when the TAiGH and TAiGL bits of ONSF or TRGSR register are ‘00 2’ (TAi IN pin input). Note 3: The port direction bit for the TAi IN pin must be set to “0” (= input mode). There are not TA2IN and TA3IN. Figure 1.12.10. TAiMR Register in PWM Mode Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 90 of 201 M16C/6S Group Timer A 1 / fi X (2 16 – 1) Count source Input signal to TA iIN pin “H” “L” Trigger is not generated by this signal 1 / fj X n PWM pulse output from TA iOUT pin “H” IR bit of TAiIC register “1” “L” “0” fj : Frequency of count source (f1, f2, f8, f32) Set to “0” upon accepting an interrupt request or by writing in program i = 0 to 4 Note 1: n = 000016 to FFFE16. Note 2: This timing diagram is for the case where the TAi register is ‘0003 16,’ the TAiGH and TAiGL bits of ONSF or TRGSR register = ‘002’ (TAi IN pin input), the MR1 bit of TAiMR register = 1 (rising edge), and the MR2 bit of TAiMR register = 1 (trigger selected by TAiTGH and TAiTGL bits). Figure 1.12.11. Example of 16-bit Pulse Width Modulator Operation 1 / fj X (m + 1) X (2 8 – 1) Count source (Note1) Input signal to TA iIN pin “H” “L” 1 / fj X (m + 1) “H” Underflow signal of 8-bit prescaler (Note2) “L” 1 / fj X (m + 1) X n PWM pulse output from TA iOUT pin IR bit of TAiIC register “H” “L” “1” “0” fj : Frequency of count source (f1, f2, f8, f32) i = 0 to 4 Set to “0” upon accepting an interrupt request or by writing in program Note 1: The 8-bit prescaler counts the count source. Note 2: The 8-bit pulse width modulator counts the 8-bit prescaler's underflow signal. Note 3: m = 0016 to FF16; n = 0016 to FE16. Note 4: This timing diagram is for the case where the TAi register is ‘0202 16,’ the TAiGH and TAiGL bits of ONSF or TRGSR register = ‘002’ (TAi IN pin input), the MR1 bit of TAiMR register = 0 (falling edge), and the MR2 bit of TAiMR register = 1 (trigger selected by TAiTGH and TAiTGL bits). Figure 1.12.12. Example of 8-bit Pulse Width Modulator Operation Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 91 of 201 M16C/6S Group Serial I/O Serial I/O Serial I/O is configured with five channels: UART0 to UART2, SI/O3 and SI/O4. UARTi (i=0 to 2) UARTi each have an exclusive timer to generate a transfer clock, so they operate independently of each other. Figure 1.13.1 shows the block diagram of UARTi. Figure 1.13.2 shows the block diagram of the UARTi transmit/receive unit. UARTi has the following modes: • Clock synchronous serial I/O mode • Clock asynchronous serial I/O mode (UART mode). • Special mode 1 (I2C mode) • Special mode 2 Figures 1.13.3 to 1.13.8 show the UARTi-related registers. Refer to tables listing each mode for register setting. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 92 of 201 M16C/6S Group Serial I/O 1/2 Main clock or on-chip oscillator clock f2SIO 0 f1SIO 1 PCLK1 f1SIO or f2SIO f8SIO 1/8 (UART0) 1/4 RXD polarity reversing circuit RXD0 CLK1 to CLK0 f1SIO or f2SIO 00h CKDIR Internal 01h f8SIO 10h f32SIO Receive clock Reception control circuit Clock synchronous type 001 Transmit/ receive unit TXD polarity reversing circuit TXD0 U0BRG register 0 UART transmission 010, 100, 101, 110 Clock synchronous type 001 1 / (n0+1) 1 UART reception SMD2 toSMD0 010, 100, 101, 110 1/16 Clock source selection f32SIO 1/16 External 1/2 Transmit clock Transmission control circuit Clock synchronous type (when internal clock is selected) 0 1 CLK0 Clock synchronous CKDIR type (when external clock is selected) Clock synchronous type (when internal clock is selected) CKPOL CLK polarity reversing circuit CTS/RTS disabled CTS/RTS selected CTS0 / RTS0 RTS0 1 VSS CRS 0 RCSP 0 1 CTS0 from UART1 0 n0: Values set to the U0BRG register PCLK1: Bit in the PCLKR register SMD2 to SMD0, CKDIR: Bits in U0MR register CLK1 to CLK0, CKPOL, CRD, CRS: Bits in U0C0 register CLKMD0, CLKMD1, RCSP: Bits in UCON register CTS/RTS disabled 1 CTS0 CRD 1/2 1/2 Main clock or on-chip oscillator clock f2SIO 0 f1SIO 1 PCLK1 f1SIO or f2SIO f8SIO 1/8 f32SIO 1/4 (UART1) RXD polarity reversing circuit RXD1 1/16 Clock source selection CLK1 to CLK0 CKDIR 00 Internal f1SIO or f2SIO 01 0 f8SIO 10 f32SIO 1 U1BRG register 1 / (n1+1) 1/16 UART reception SMD2 to SMD0 010, 100, 101, 110 UART transmission 010, 100, 101, 110 1/2 CLK1 0 CLKMD0 Receive clock Transmit/ receive unit TXD1 Transmit clock Clock synchronous type (when internal clock is selected) 0 Clock synchronous type (when external clock is selected)) CLK polarity reversing circuit Transmission control circuit Clock synchronous type 001 External CKPOL Reception control circuit Clock synchronous type 001 TXD polarity reversing circuit 1 CKDIR Clock synchronous type (when internal clock is selected) 1 CTS1 / RTS1/ CTS0 / CLKS1 1 CTS/RTS selected CTS/RTS disabled CRS 1 Clock output pin select 0 RTS1 VSS CLKMD1 0 1 CTS/RTS disabled CTS1 0 0 1 CRD CTS0 from UART0 RCSP 1/2 Main clock or on-chip oscillator clock f2SIO 0 f1SIO 1 PCLK1 f1SIO or f2SIO f8SIO 1/8 (UART2) 1/4 RXD polarity reversing circuit RXD2 1/16 Clock source selection CLK1 to CLK0 CKDIR 00 Internal f1SIO or f2SIO 01 0 f8SIO 10 f32SIO UART reception SMD2 to SMD0 010, 100, 101, 110 Clock synchronous type 001 Reception control circuit UART transmission 1/16 010, 100, 101, 110 Clock synchronous type 001 Transmission control circuit 1/2 TXD polarity reversing circuit (1) TXD2 RTS2 1 VSS CTS/RTS disabled 1 0 Transmit clock CKDIR CTS/RTS disabled CTS2 CRD NOTES : 1. UART2 is the N-channel open-drain output. Cannot be set to the CMOS output. 2. UART2 does not have CLK2 port. So CKDIR must not be set "1." Figure 1.13.1. UARTi Block Diagram Rev.5.01 Dec 10, 2009 REJ03B0014-0501 Receive clock Transmit/ receive unit Clock synchronous type (when internal clock is selected) 0 CTS/RTS selected CRS 0 f32SIO U2BRG register 1 / (n2+1) External CTS2 / RTS2 n1: Values set to the U1BRG register PCLK1: Bit in the PCLKR register SMD2 to SMD0, CKDIR: Bits in U1MR register CLK1 to CLK0, CKPOL, CRD, CRS: Bits in U1C0 register CLKMD0, CLKMD1, RCSP: Bits in UCON register page 93 of 201 n2: Values set to the U2BRG register PCLK1: Bit in the PCLKR register SMD2 to SMD0, CKDIR: Bits in U2MR register CLK1 to CLK0, CKPOL, CRD, CRS: Bits in U2C0 register CLKMD0, CLKMD1, RCSP: Bits in UCON register M16C/6S Group Serial I/O IOPOL No reverse RXDi 0 RXD data reverse circuit 1 Clock synchronous type Reverse PRYE STPS PAR disabled 1SP Clock synchronous type 0 0 SP SP UART(7 bits) UARTi receive register 0 0 0 PAR 1 1 1 1 SMD2 to SMD0 UART (9 bits) PAR enabled 2SP 0 UART (7 bits) UART (8 bits) 0 0 UART 0 0 0 0 1 Clock synchronous type UART (8 bits) UART (9 bits) D8 D7 D6 D5 D4 D3 D2 D1 D0 UiRB register Logic reverse circuit + MSB/LSB conversion circuit Data bus high-order bits Data bus low-order bits Logic reverse circuit + MSB/LSB conversion circuit D8 D7 D6 D5 D4 D3 D2 D1 D0 UiTB register UART (8 bits) UART (9 bits) PRYE STPS PAR enabled 2SP 1 1 SP SP PAR 0 1SP SMD2 to SMD0 UART UART (9 bits) 1 Clock synchronous type 1 1 0 0 0 0 PAR disabled Clock synchronous type UART (7 bits) UART (8 bits) Clock synchronous type i=0 to 2 SP: Stop bit PAR: Parity bit SMD2 to SMD0, STPS, PRYE, IOPOL, CKDIR: Bits in UiMR register UiERE: Bit in UiC1 register Figure 1.13.2. UARTi Transmit/Receive Unit Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 94 of 201 UARTi transmit register UART(7 bits) Error signal output disable 0 UiERE 1 Error signal output circuit Error signal output enable IOPOL 0 1 No reverse TXD data reverse circuit Reverse TXDi M16C/6S Group Serial I/O UARTi transmit buffer register (i=0 to 2)(Note) (b15) b7 (b8) b0 b7 Symbol U0TB U1TB U2TB b0 Address 03A316-03A216 03AB16-03AA16 037B16-037A16 After reset Indeterminate Indeterminate Indeterminate Function RW WO Transmit data Nothing is assigned. In an attempt to write to these bits, write “0”. The value, if read, turns out to be indeterminate. Note: Use MOV instruction to write to this register. UARTi receive buffer register (i=0 to 2) (b15) b7 (b8) b0 b7 Symbol U0RB U1RB U2RB b0 Bit symbol Address 03A716-03A616 03AF16-03AE16 037F16-037E16 Function Bit name (b7-b0) (b8) (b10-b9) After reset Indeterminate Indeterminate Indeterminate RW Receive data (D7 to D0) RO Receive data (D8) RO Nothing is assigned. In an attempt to write to these bits, write “0”. The value, if read, turns out to be “0”. ABT Arbitration lost detecting flag (Note 2) OER Overrun error flag (Note 1) 0 : No overrun error 1 : Overrun error found FER Framing error flag (Note 1) 0 : No framing error 1 : Framing error found RO PER Parity error flag (Note 1) 0 : No parity error 1 : Parity error found RO SUM Error sum flag (Note 1) 0 : No error 1 : Error found RO 0 : Not detected 1 : Detected RW RO Note 1: When the UiMR register’s SMD2 to SMD0 bits = “0002” (serial I/O disabled) or the UiC1 register’s RE bit = “0” (reception disabled), all of the SUM, PER, FER and OER bits are set to “0” (no error). The SUM bit is set to “0” (no error) when all of the PER, FER and OER bits = “0” (no error). Also, the PER and FER bits are set to “0” by reading the lower byte of the UiRB register. Note 2: The ABT bit is set to “0” by writing “0” in a program. (Writing “1” has no effect.) UARTi bit rate generator (i=0 to 2)(Notes 1, 2) b7 Symbol U0BRG U1BRG U2BRG b0 Address 03A116 03A916 037916 After reset Indeterminate Indeterminate Indeterminate Function Setting range RW Assuming that set value = n, UiBRG divides the count source by n + 1 0016 to FF16 WO Note 1: Write to this register while serial I/O is neither transmitting nor receiving. Note 2: Use MOV instruction to write to this register. Figure 1.13.3. U0TB to U2TB Register, U0RB to U2RB Register, and U0BRG to U2BRG Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 95 of 201 M16C/6S Group Serial I/O UARTi transmit/receive mode register (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol U0MR to U2MR Bit symbol SMD0 Address 03A016, 03A816, 037816 After reset 0016 Function Bit name Serial I/O mode select bit (Note 2) b2 b1 b0 RW RW 0 0 0 : Serial I/O disabled 0 0 1 : Clock synchronous serial I/O mode (Note 3) 0 1 0 : I2C mode 1 0 0 : UART mode transfer data 7 bits long 1 0 1 : UART mode transfer data 8 bits long 1 1 0 : UART mode transfer data 9 bits long Must not be set except above RW CKDIR Internal/external clock select bit 0 : Internal clock 1 : External clock (Note 1) RW STPS Stop bit length select bit 0 : One stop bit 1 : Two stop bits PRY Odd/even parity select bit Effective when PRYE = 1 0 : Odd parity 1 : Even parity PRYE Parity enable bit 0 : Parity disabled 1 : Parity enabled RW IOPOL TxD, RxD I/O polarity reverse bit 0 : No reverse 1 : Reverse RW SMD1 SMD2 (Note 4) RW RW RW Note 1: Set the corresponding port direction bit for each CLKi pin to “0” (input mode). Note 2: To receive data, set the corresponding port direction bit for each RxDi pin to “0” (input mode). Note 3: Set the corresponding port direction bit for SCL and SDA pins to “0” (input mode). Note 4: Set “0” to select internal clock of UART2. UARTi transmit/receive control register 0 (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol U0C0 to U2C0 Bit symbol CLK0 Address After reset 03A416, 03AC16, 037C16 000010002 Bit name BRG count source select bit CLK1 CRS TXEPT CRD CTS/RTS function select bit (Note 4) Function b1 b0 0 0 : f1SIO or f2SIO is selected 0 1 : f8SIO is selected 1 0 : f32SIO is selected 1 1 : Must not be set Effective when CRD = 0 0 : CTS function is selected (Note 1) 1 : RTS function is selected Transmit register empty 0 : Data present in transmit register (during transmission) 1 : No data present in transmit register flag (transmission completed) CTS/RTS disable bit RW RW RW RW RO 0 : CTS/RTS function enabled 1 : CTS/RTS function disabled (P60, P64 and P73 can be used as I/O ports) RW NCH Data output select bit (Note 2) 0 : TxDi/SDAi and SCLi pins are CMOS output 1 : TxDi/SDAi and SCLi pins are N-channel open-drain output RW CKPOL CLK polarity select bit 0 : Transmit data is output at falling edge of transfer clock and receive data is input at rising edge 1 : Transmit data is output at rising edge of transfer clock and receive data is input at falling edge RW UFORM Transfer format select bit 0 : LSB first (Note 3) 1 : MSB first RW Note 1: Set the corresponding port direction bit for each CTSi pin to “0” (input mode). Note 2: TXD2/SDA2 are N-channel open-drain output. Cannot be set to the CMOS output. NCH bit of U2C0 register is effective in an output set up of SCL2 pin. Note 3: Effective for clock synchronous serial I/O mode and UART mode transfer data 8 bits long. Note 4: CTS1/RTS1 can be used when the UCON register’s CLKMD1 bit = “0” (only CLK1 output) and the UCON register’s RCSP bit = “0” (CTS0/RTS0 not separated). Figure 1.13.4. U0MR to U2MR Register and U0C0 to U2C0 Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 96 of 201 M16C/6S Group Serial I/O UARTi transmit/receive control register 1 (i=0, 1) b7 b6 b5 b4 b3 b2 b1 Symbol U0C1, U1C1 b0 Bit symbol Address 03A516,03AD16 After reset 000000102 Function Bit name RW TE Transmit enable bit 0 : Transmission disabled 1 : Transmission enabled RW TI Transmit buffer empty flag 0 : Data present in UiTB register 1 : No data present in UiTB register RO RE Receive enable bit 0 : Reception disabled 1 : Reception enabled RW RI Receive complete flag 0 : No data present in UiRB register 1 : Data present in UiRB register RO (b5-b4) Nothing is assigned. When write, set “0”. When read, these contents are “0”. UiLCH Data logic select bit 0 : No reverse 1 : Reverse RW UiERE Error signal output enable bit 0 : Output disabled 1 : Output enabled RW NOTES: 1. The UiLCH bit is enabled when the SMD2 to SMD0 bits in the UiMR register are set to “001b” (clock synchronous serial I/O mode), “100b” (UART mode, 7-bit transfer data), or “101b” (UART mode, 8-bit transfer data). Set this bit to “0” when the SMD2 to SMD0 bits are set to “010b” (I2C mode) or “110b” (UART mode, 9-bit transfer data). UART2 transmit/receive control register 1 b7 b6 b5 b4 b3 b2 b1 Symbol U2C1 b0 Bit symbol Address 037D16 After reset 000000102 Function Bit name RW TE Transmit enable bit 0 : Transmission disabled 1 : Transmission enabled RW TI Transmit buffer empty flag 0 : Data present in U2TB register 1 : No data present in U2TB register RO RE Receive enable bit 0 : Reception disabled 1 : Reception enabled RW RI Receive complete flag 0 : No data present in U2RB register 1 : Data present in U2RB register RO 0 : Transmit buffer empty (TI = 1) 1 : Transmit is completed (TXEPT = 1) RW U2RRM UART2 continuous receive mode enable bit 0 : Continuous receive mode disabled 1 : Continuous receive mode enabled RW U2LCH Data logic select bit 0 : No reverse 1 : Reverse RW U2ERE Error signal output enable bit 0 : Output disabled 1 : Output enabled RW U2IRS UART2 transmit interrupt cause select bit NOTES: 1. The U2LCH bit is enabled when the SMD2 to SMD0 bits in the U2MR registerare set to “001b” (clock synchronous serial I/O mode), “100b” (UART mode, 7-bit transfer data), or “101b” (UART mode, 8-bit transfer data). Set this bit to “0” when the SMD2 to SMD0 bits are set to “010b” (I2C mode) or “110b” (UART mode, 9-bit transfer data). Figure 1.13.5. U0C1 to U2C1 Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 97 of 201 M16C/6S Group Serial I/O UART transmit/receive control register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol UCON Bit symbol Address 03B016 After reset X00000002 Function Bit name UART0 transmit interrupt cause select bit 0 : Transmit buffer empty (Tl = 1) 1 : Transmission completed (TXEPT = 1) RW UART1 transmit interrupt cause select bit 0 : Transmit buffer empty (Tl = 1) 1 : Transmission completed (TXEPT = 1) RW U0RRM UART0 continuous receive mode enable bit 0 : Continuous receive mode disabled 1 : Continuous receive mode enable RW U1RRM UART1 continuous receive mode enable bit 0 : Continuous receive mode disabled 1 : Continuous receive mode enabled RW CLKMD0 UART1 CLK/CLKS select bit 0 Effective when CLKMD1 = “1” 0 : Clock output from CLK1 1 : Clock output from CLKS1 RW CLKMD1 UART1 CLK/CLKS select bit 1 (Note) 0 : CLK output is only CLK1 1 : Transfer clock output from multiple pins function selected RW RCSP 0 : CTS/RTS shared pin 1 : CTS/RTS separated (CTS0 supplied from the P64 pin) RW U0IRS U1IRS Separate UART0 CTS/RTS bit RW Nothing is assigned. When write, set “0”. When read, its content is indeterminate. (b7) Note: When using multiple transfer clock output pins, make sure the following conditions are met: U1MR register’s CKDIR bit = “0” (internal clock) UART2 special mode register (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol Address U0SMR to U2SMR 036F16, 037316, 037716 0 Bit symbol After reset X00000002 Function Bit name IICM I2C mode select bit 0 : Other than I2C mode 1 : I2C mode RW ABC Arbitration lost detecting flag control bit 0 : Update per bit 1 : Update per byte RW BBS Bus busy flag 0 : STOP condition detected 1 : START condition detected (busy) (b3-b6) Reserved bit Set to “0” Nothing is assigned. When write, set “0”. When read, its content is indeterminate. (b7) Note 1: The BBS bit is set to “0” by writing “0” in a program. (Writing “1” has no effect.). Figure 1.13.6. UCON Register and U0SMR to U2SMR Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 RW page 98 of 201 RW (Note1) RW M16C/6S Group Serial I/O UARTi special mode register 2 (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address U0SMR2 to U2SMR2 036E16, 037216, 037616 Bit symbol After reset X00000002 Bit name Function RW IICM2 I 2C mode select bit 2 Refer to Table 1.16.4 CSC Clock-synchronous bit 0 : Disabled 1 : Enabled RW SWC SCL wait output bit 0 : Disabled 1 : Enabled RW ALS SDA output stop bit 0 : Disabled 1 : Enabled RW STAC UARTi initialization bit 0 : Disabled 1 : Enabled RW SWC2 SCL wait output bit 2 0: Transfer clock 1: 0 output RW SDHI SDA output disable bit 0: Enabled 1: Disabled (high impedance) RW RW Nothing is assigned. When write, set “0”. When read, its content is indeterminate. (b7) UARTi special mode register 3 (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol U0SMR3 to U2SMR3 Bit symbol (b0) CKPH (b2) NODC (b4) DL0 Address 036D16, 037116, 037516 Bit name After reset 000X0X0X2 Function RW Nothing is assigned. When write, set “0”. When read, its content is indeterminate. Clock phase set bit 0 : Without clock delay 1 : With clock delay RW Nothing is assigned. When write, set “0”. When read, its content is indeterminate. Clock output select bit 0 : CLKi is CMOS output 1 : CLKi is N-channel open drain output RW Nothing is assigned. When write, set “0”. When read, its content is indeterminate. SDAi digital delay setup bit (Note 1, Note 2) DL1 DL2 b7 b6 b5 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 : Without delay 1 : 1 to 2 cycle(s) of UiBRG count source 0 : 2 to 3 cycles of UiBRG count source 1 : 3 to 4 cycles of UiBRG count source 0 : 4 to 5 cycles of UiBRG count source 1 : 5 to 6 cycles of UiBRG count source 0 : 6 to 7 cycles of UiBRG count source 1 : 7 to 8 cycles of UiBRG count source RW RW RW Note 1 : The DL2 to DL0 bits are used to generate a delay in SDAi output by digital means during I2C mode. In other than I2C mode, set these bits to “0002” (no delay). Note 2 : The amount of delay varies with the load on SCLi and SDAi pins. Also, when using an external clock, the amount of delay increases by about 100 ns. Figure 1.13.7. U0SMR2 to U2SMR2 Registers and U0SMR3 to U2SMR3 Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 99 of 201 M16C/6S Group Serial I/O UARTi special mode register 4 (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address U0SMR4 to U2SMR4 036C16, 037016, 037416 Bit symbol Bit name Function RW Start condition generate bit (Note) 0 : Clear 1 : Start RW RSTAREQ Restart condition generate bit (Note) 0 : Clear 1 : Start RW STPREQ Stop condition generate bit (Note) 0 : Clear 1 : Start RW STSPSEL SCL,SDA output select bit 0 : Start and stop conditions not output 1 : Start and stop conditions output RW ACKD ACK data bit 0 : ACK 1 : NACK RW ACKC ACK data output enable bit 0 : Serial I/O data output 1 : ACK data output RW SCLHI SCL output stop enable bit 0 : Disabled 1 : Enabled RW SWC9 SCL wait bit 3 0 : SCL “L” hold disabled 1 : SCL “L” hold enabled RW STAREQ Note: Set to “0” when each condition is generated. Figure 1.13.8. U0SMR4 to U2SMR4 Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 After reset 0016 page 100 of 201 M16C/6S Group Clock Synchronous serial I/O Mode Clock Synchronous serial I/O Mode The clock synchronous serial I/O mode uses a transfer clock to transmit and receive data. Table 1.14.1 lists the specifications of the clock synchronous serial I/O mode. Table 1.14.2 lists the registers used in clock synchronous serial I/O mode and the register values set. UART2 is not available in this mode. Table 1.14.1. Clock Synchronous Serial I/O Mode Specifications Item Specification Transfer data format Transfer clock Transmission, reception control Transmission start condition • Transfer data length: 8 bits • UiMR(i=0 to 1) register’s CKDIR bit = “0” (internal clock) : fj/ 2(n+1) fj = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of UiBRG register 0016 to FF16 • CKDIR bit = “1” (external clock) : Input from CLKi pin _______ _______ _______ _______ • Selectable from CTS function, RTS function or CTS/RTS function disable • Before transmission can start, the following requirements must be met (Note 1) _ The TE bit of UiC1 register= 1 (transmission enabled) _ The TI bit of UiC1 register = 0 (data present in UiTB register) _ Reception start condition Interrupt request generation timing Error detection Select function _______ _______ If CTS function is selected, input on the CTSi pin = “L” • Before reception can start, the following requirements must be met (Note 1) _ The RE bit of UiC1 register= 1 (reception enabled) _ The TE bit of UiC1 register= 1 (transmission enabled) _ The TI bit of UiC1 register= 0 (data present in the UiTB register) • For transmission, one of the following conditions can be selected _ The UiIRS bit (Note 3) = 0 (transmit buffer empty): when transferring data from the UiTB register to the UARTi transmit register (at start of transmission) _ The UiIRS bit =1 (transfer completed): when the serial I/O finished sending data from the UARTi transmit register • For reception When transferring data from the UARTi receive register to the UiRB register (at completion of reception) • Overrun error (Note 2) This error occurs if the serial I/O started receiving the next data before reading the UiRB register and received the 7th bit of the next data • CLK polarity selection Transfer data input/output can be chosen to occur synchronously with the rising or the falling edge of the transfer clock • LSB first, MSB first selection Whether to start sending/receiving data beginning with bit 0 or beginning with bit 7 can be selected • Continuous receive mode selection Reception is enabled immediately by reading the UiRB register • Switching serial data logic This function reverses the logic value of the transmit/receive data • Transfer clock output from multiple pins selection (UART1) The output pin can be selected in a program from two UART1 transfer clock pins that have been set _______ _______ • Separate CTS/RTS pins (UART0) _________ _________ CTS0 and RTS0 are input/output from separate pins Note 1: When an external clock is selected, the conditions must be met while if the UiC0 register’s CKPOL bit = “0” (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock), the external clock is in the high state; if the UiC0 register’s CKPOL bit = “1” (transmit data output at the rising edge and the receive data taken in at the falling edge of the transfer clock), the external clock is in the low state. Note 2: If an overrun error occurs, the value of UiRB register will be indeterminate. The IR bit of SiRIC register does not change. Note 3: The U0IRS and U1IRS bits respectively are the UCON register bits 0 and 1. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 101 of 201 M16C/6S Group Clock Synchronous serial I/O Mode Table 1.14.2. Registers to Be Used and Settings in Clock Synchronous Serial I/O Mode Register UiTB(Note3) Bit Function 0 to 7 Set transmission data UiRB(Note3) 0 to 7 UiBRG Reception data can be read OER Overrun error flag 0 to 7 Set a transfer rate UiMR(Note3) SMD2 to SMD0 UiC0 Set to “0012” CKDIR Select the internal clock or external clock IOPOL Set to “0” CLK1 to CLK0 Select the count source for the UiBRG register CRS Select CTS or RTS to use TXEPT Transmit register empty flag CRD Enable or disable the CTS or RTS function NCH Select TxDi pin output mode CKPOL Select the transfer clock polarity UFORM Select the LSB first or MSB first TE Set this bit to “1” to enable transmission/reception _______ _______ _______ UiC1 _______ TI Transmit buffer empty flag RE Set this bit to “1” to enable reception RI Reception complete flag U2IRS (Note 1) Select the source of UART2 transmit interrupt U2RRM (Note 1) Set this bit to “1” to use continuous receive mode UiLCH Set this bit to “1” to use inverted data logic UiERE Set to “0” UiSMR 0 to 7 Set to “0” UiSMR2 0 to 7 Set to “0” UiSMR3 0 to 2 Set to “0” NODC Select clock output mode 4 to 7 Set to “0” UiSMR4 0 to 7 Set to “0” UCON U0IRS, U1IRS Select the source of UART0/UART1 transmit interrupt U0RRM, U1RRM Set this bit to “1” to use continuous receive mode CLKMD0 Select the transfer clock output pin when CLKMD1 = 1 CLKMD1 Set this bit to “1” to output UART1 transfer clock from two pins RCSP Set this bit to “1” to accept as input the UART0 CTS0 signal from the P64 pin 7 Set to “0” _________ Note 1: Set the U0C1 and U1C1 register bit 4 and bit 5 to “0”. The U0IRS, U1IRS, U0RRM and U1RRM bits are in the UCON register. Note 2: Not all register bits are described above. Set those bits to “0” when writing to the registers in clock synchronous serial I/O mode. i=0 to 1 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 102 of 201 M16C/6S Group Clock Synchronous serial I/O Mode Table 1.14.3 lists the functions of the input/output pins during clock synchronous serial I/O mode. Table 1.14.3 shows pin functions for the case where the multiple transfer clock output pin select function is deselected. Table 1.14.4 lists the P64 pin functions during clock synchronous serial I/O mode. Note that for a period from when the UARTi operation mode is selected to when transfer starts, the TxDi pin outputs an “H”. (If the N-channel open-drain output is selected, this pin is in a high-impedance state.) Table 1.14.3. Pin Functions (When Not Select Multiple Transfer Clock Output Pin Function) Pin name Function TxDi (i = 0 to 2) Serial data output (P63, P67) Method of selection (Outputs dummy data when performing reception only) RxDi (P62, P66) Serial data input PD6 register’s PD6_2 bit=0, PD6_6 bit=0 (Can be used as an input port when performing transmission only) CLKi (P61, P65) Transfer clock output UiMR register’s CKDIR bit=0 Transfer clock input UiMR register’s CKDIR bit=1 PD6 register’s PD6_1 bit=0, PD6_5 bit=0 CTS input UiC0 register’s CRD bit=0 UiC0 register’s CRS bit=0 PD6 register’s PD6_0 bit=0, PD6_4 bit=0 RTS output UiC0 register’s CRD bit=0 UiC0 register’s CRS bit=1 I/O port UiC0 register’s CRD bit=1 CTSi/RTSi (P60, P64) Table 1.14.4. P64 Pin Functions Pin function P64 CTS1 RTS1 CTS0(Note1) CLKS1 Bit set value U1C0 register CRS CRD 1 0 0 0 1 0 0 RCSP 0 0 0 1 UCON register CLKMD1 CLKMD0 0 0 0 0 1(Note 2) PD6 register PD6_4 Input: 0, Output: 1 0 0 1 Note 1: In addition to this, set the U0C0 register’s CRD bit to “0” (CTS0/RTS0 enabled) and the U0 C0 register’s CRS bit to “1” (RTS0 selected). Note 2: When the CLKMD1 bit = 1 and the CLKMD0 bit = 0, the following logic levels are output: • High if the U1C0 register’s CLKPOL bit = 0 • Low if the U1C0 register’s CLKPOL bit = 1 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 103 of 201 M16C/6S Group Clock Synchronous serial I/O Mode (1) Example of transmit timing (when internal clock is selected) Tc Transfer clock UiC1 register TE bit UiC1 register TI bit “1” “0” Write data to the UiTB register “1” “0” Transferred from UiTB register to UARTi transmit register “H” CTSi TCLK “L” Stopped pulsing because CTSi = “H” Stopped pulsing because the TE bit = “0” CLKi TxDi D0 D 1 D2 D3 D4 D5 D6 D7 UiC0 register TXEPT bit “1” SiTIC register IR bit “1” D 0 D 1 D 2 D3 D4 D 5 D 6 D 7 D 0 D 1 D 2 D 3 D 4 D 5 D6 D 7 “0” “0” Cleared to “0” when interrupt request is accepted, or cleared to “0” in a program Tc = TCLK = 2(n + 1) / fj fj: frequency of UiBRG count source (f1SIO, f2SIO, f8SIO, f32SIO) n: value set to UiBRG register i: 0 to 2 The above timing diagram applies to the case where the register bits are set as follows: • UiMR register CKDIR bit = 0 (internal clock) • UiC0 register CRD bit = 0 (CTS/RTS enabled), CRS bit = 0 (CTS selected) • UiC0 register CKPOL bit = 0 (transmit data output at the falling edge and receive data taken in at the rising edge of the transfer clock) • UiRS bit = 0 (an interrupt request occurs when the transmit buffer becomes empty): U0IRS bit is the UCON register bit 0, U1IRS bit is the UCON register bit 1, and U2IRS bit is the U2C1 register bit 4 (2) Example of receive timing (when external clock is selected) “1” UiC1 register RE bit “0” UiC1 register TE bit “0” UiC1 register TI bit “1” Write dummy data to UiTB register “1” “0” Transferred from UiTB register to UARTi transmit register “H” RTSi “L” Even if the reception is completed, the RTS does not change. The RTS becomes “L” when the RI bit changes to “0” from “1”. 1 / fEXT CLKi Receive data is taken in D 0 D1 D 2 D3 D 4 D5 D6 D 7 RxDi UiC1 register RI bit “1” SiTIC register IR bit “1” Transferred from UARTi receive register to UiRB register D0 D 1 D 2 D3 D 4 D 5 Read out from UiRB register “0” “0” Cleared to “0” when interrupt request is accepted, or cleared to “0” in a program The above timing diagram applies to the case where the register bits are set Make sure the following conditions are met when input as follows: to the CLKi pin before receiving data is high: • UiMR register CKDIR bit = 1 (external clock) • UiC0 register TE bit = 1 (transmit enabled) • UiC0 register CRD bit = 0 (CTS/RTS enabled), CRS bit = 1 (RTS selected) • UiC0 register RE bit = 1 (Receive enabled) • UiC0 register CKPOL bit = 0 (transmit data output at the falling edge and receive • Write dummy data to the UiTB register data taken in at the rising edge of the transfer clock) fEXT: frequency of external clock Figure 1.14.1. Transmit and Receive Operation Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 104 of 201 M16C/6S Group Clock Synchronous serial I/O Mode Counter Measure for Communication Error Occurs If a communication error occurs while transmitting or receiving in clock synchronous serial I/O mode, follow the procedures below. • Resetting the UiRB register (i=0 to 2) (1) Set the RE bit in the UiC1 register to “0” (reception disabled) (2) Set the SMD2 to SMD0 bits in the UiMR register to “000b” (Serial I/O disabled) (3) Set the SMD2 to SMD0 bits in the UiMR register to “001b” (Clock synchronous serial I/O mode) (4) Set the RE bit in the UiC1 register to “1” (reception enabled) • Resetting the UiTB register (i=0 to 2) (1) Set the SMD2 to SMD0 bits in the UiMR register “000b” (Serial I/O disabled) (2) Set the SMD2 to SMD0 bits in the UiMR register “001b” (Clock synchronous serial I/O mode) (3) “1” is written to RE bit in the UiC1 register (reception enabled), regardless of the TE bit in the UiCi register (a) CLK Polarity Select Function Use the UiC0 register (i = 0 to 1)’s CKPOL bit to select the transfer clock polarity. Figure 1.14.2 shows the polarity of the transfer clock. (1) When the UiC0 register’s CKPOL bit = 0 (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock) CLKi (Note 2) TXDi D0 D1 D2 D3 D4 D5 D6 D7 RXDi D0 D1 D2 D3 D4 D5 D6 D7 (2) When the UiC0 register’s CKPOL bit = 1 (transmit data output at the rising edge and the receive data taken in at the falling edge of the transfer clock) (Note 3) CLKi TXDi D0 D1 D2 D3 D4 D5 D6 D7 R XD i D0 D1 D2 D3 D4 D5 D6 D7 Note 1: This applies to the case where the UiC0 register’s UFORM bit = 0 (LSB first) and UiC1 register's UiLCH bit = 0 (no reverse). Note 2: When not transferring, the CLKi pin outputs a high signal. Note 3: When not transferring, the CLKi pin outputs a low signal. i = 0 to 1 Figure 1.14.2. Transfer Clock Polarity Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 105 of 201 M16C/6S Group Clock Synchronous serial I/O Mode (b) LSB First/MSB First Select Function Use the UiC0 register (i = 0 to 1)’s UFORM bit to select the transfer format. Figure 1.14.3 shows the transfer format. (1) When UiC0 register's UFORM bit = 0 (LSB first) CLKi TXDi D0 D1 D2 D3 D4 D5 D6 D7 RXDi D0 D1 D2 D3 D4 D5 D6 D7 (2) When UiC0 register's UFORM bit = 1 (MSB first) CLKi TXDi D7 D6 D5 D4 D3 D2 D1 D0 RXDi D7 D6 D5 D4 D3 D2 D1 D0 Note: This applies to the case where the UiC0 register’s CKPOL bit = 0 ( transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock) and the UiC1 register’s UiLCH bit = 0 (no reverse). i = 0 to 1 Figure 1.14.3. Transfer Format (c) Continuous Receive Mode In continuous receive mode, receive operation becomes enable when the receive buffer register is read. It is not necessary to write dummy data into the transmit buffer register to enable receive operation in this mode. However, a dummy read of the receive buffer register is required when starting the operation mode. When the UiRRM bit (i = 0 to 1) = 1 (continuous receive mode), the UiC1 register’s TI bit is set to “1” (data present in the UiTB register) by reading the UiRB register. In this case, i.e., UiRRM bit = 1, do not write dummy data to the UiTB register in a program. The U0RRM and U1RRM bits are the UCON register bit 2 and bit 3, respectively. (d) Serial Data Logic Switching Function When the UiC1 register (i = 0 to 1)’s UiLCH bit = 1 (reverse), the data written to the UiTB register has its logic reversed before being transmitted. Similarly, the received data has its logic reversed when read from the UiRB register. Figure 1.14.4 shows serial data logic. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 106 of 201 M16C/6S Group Clock Synchronous serial I/O Mode (1) When the UiC1 register's UiLCH bit = 0 (no reverse) Transfer clock “H” “L” TxDi “H” (no reverse) “L” D0 D1 D2 D3 D4 D5 D6 D7 (2) When the UiC1 register's UiLCH bit = 1 (reverse) Transfer clock “H” “L” TxDi “H” (reverse) “L” D0 D1 D2 D3 D4 D5 D6 D7 Note: This applies to the case where the UiC0 register’s CKPOL bit = 0 (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock) and the UFORM bit = 0 (LSB first). i = 0 to 1 Figure 1.14.4. Serial Data Logic Switching (e) Transfer Clock Output From Multiple Pins (UART1) Use the UCON register’s CLKMD1 to CLKMD0 bits to select one of the two transfer clock output pins. (See Figure 1.14.5.) This function can be used when the selected transfer clock for UART1 is an internal clock. Microcomputer TXD1 (P67) CLKS1 (P64) CLK1 (P65) IN IN CLK CLK Transfer enabled when the UCON register's CLKMD0 bit = 0 Transfer enabled when the UCON register's CLKMD0 bit = 1 Note: This applies to the case where the U1MRregister's CKDIR bit = 0 (internal clock) and the UCON register's CLKMD1 bit = 1 ( transfer clock output from multiple pins). Figure 1.14.5. Transfer Clock Output From Multiple Pins Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 107 of 201 Clock Synchronous serial I/O Mode M16C/6S Group _______ _______ CTS/RTS Function _______ ________ When the CTS function is used transmit and receive operation start when “L” is applied to the CTSi/ ________ ________ ________ RTSi (i=0 to 2) pin. Transmit and receive operation begins when the CTSi/RTSi pin is held “L”. If the “L” signal is switched to “H” during a transmit or receive operation, the operation stops before the next data. _______ ________ ________ When the RTS function is used, the CTSi/RTSi pin outputs on “L” signal when the microcomputer is ready to receive. The output level becomes “H” on the first falling edge of the CLKi pin. _______ _______ • CRD bit in UiC0 register = 1 ( CTS/RTS function disabled) ________ ________ CTSi/RTSi pin is programmable I/O function _______ ________ ________ _______ • CRD bit = 0, CRS bit = 0 (CTS function is selected) CTSi/RTSi pin is CTS function _______ ________ ________ _______ • CRD bit = 0, CRS bit = 1 (RTS function is selected) CTSi/RTSi pin is RTS function _______ _______ (f) CTS/RTS Separate Function (UART0) _______ _______ _______ _______ This function separates CTS0/RTS0, outputs RTS0 from the P60 pin, and accepts as input the CTS0 from the P64 pin. To use this function, set the register bits as shown below. _______ _______ • U0C0 register's CRD bit = 0 (enables UART0 CTS/RTS) _______ • U0C0 register's CRS bit = 1 (outputs UART0 RTS) _______ _______ • U1C0 register's CRD bit = 0 (enables UART1 CTS/RTS) _______ • U1C0 register's CRS bit = 0 (inputs UART1 CTS) _______ • UCON register's RCSP bit = 1 (inputs CTS0 from the P64 pin) • UCON register's CLKMD1 bit = 0 (CLKS1 not used) _______ _______ _______ _______ Note that when using the CTS/RTS separate function, UART1 CTS/RTS separate function cannot be used. IC Microcomputer TXD0 (P63) RXD0 (P62) IN OUT CLK0 (P61) CLK RTS0 (P60) CTS CTS0 (P64) RTS _______ _______ Figure 1.14.6. CTS/RTS Separate Function Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 108 of 201 M16C/6S Group UART Mode Clock Asynchronous Serial I/O (UART) Mode The UART mode allows transmitting and receiving data after setting the desired transfer rate and transfer data format. Table 1.15.1 lists the specifications of the UART mode. Table 1.15.1. UART Mode Specifications Item Transfer data format Transfer clock Transmission, reception control Transmission start condition Reception start condition Interrupt request generation timing Error detection Specification • Character bit (transfer data): Selectable from 7, 8 or 9 bits • Start bit: 1 bit • Parity bit: Selectable from odd, even, or none • Stop bit: Selectable from 1 or 2 bits • UiMR(i=0 to 2) register’s CKDIR bit = 0 (internal clock) : fj/ 16(n+1) 0016 to FF16 fj = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of UiBRG register • CKDIR bit = “1” (external clock) : fEXT/16(n+1) (Note 3) fEXT: Input from CLKi pin. n :Setting value of UiBRG register 0016 to FF16 _______ _______ _______ _______ • Selectable from CTS function, RTS function or CTS/RTS function disable • Before transmission can start, the following requirements must be met _ The TE bit of UiC1 register= 1 (transmission enabled) _ The TI bit of UiC1 register = 0 (data present in UiTB register) _______ _______ _ If CTS function is selected, input on the CTSi pin = “L” • Before reception can start, the following requirements must be met _ The RE bit of UiC1 register= 1 (reception enabled) _ Start bit detection • For transmission, one of the following conditions can be selected _ The UiIRS bit (Note 2) = 0 (transmit buffer empty): when transferring data from the UiTB register to the UARTi transmit register (at start of transmission) _ The UiIRS bit =1 (transfer completed): when the serial I/O finished sending data from the UARTi transmit register • For reception When transferring data from the UARTi receive register to the UiRB register (at completion of reception) • Overrun error (Note 1) This error occurs if the serial I/O started receiving the next data before reading the UiRB register and received the bit one before the last stop bit of the next data • Framing error This error occurs when the number of stop bits set is not detected • Parity error This error occurs when if parity is enabled, the number of 1’s in parity and character bits does not match the number of 1’s set • Error sum flag This flag is set (= 1) when any of the overrun, framing, and parity errors is encountered Select function • LSB first, MSB first selection Whether to start sending/receiving data beginning with bit 0 or beginning with bit 7 can be selected • Serial data logic switch This function reverses the logic of the transmit/receive data. The start and stop bits are not reversed. • TXD, RXD I/O polarity switch This function reverses the polarities of hte TXD pin output and RXD pin input. The logic levels of all I/O data is reversed. _______ _______ • Separate CTS/RTS pins (UART0) _________ _________ CTS0 and RTS0 are input/output from separate pins Note 1: If an overrun error occurs, the value of UiRB register will be indeterminate. The IR bit of SiRIC register does not change. Note 2: The U0IRS and U1IRS bits respectively are the UCON register bits 0 and 1; the U2IRS bit is the U2C1 register bit 4. Note 3: CKDIR of U2MR must be set “0” to select internal clock. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 109 of 201 M16C/6S Group UART Mode Table 1.15.2. Registers to Be Used and Settings in UART Mode Register UiTB UiRB Bit Function 0 to 8 Set transmission data (Note 1) 0 to 8 Reception data can be read (Note 1) OER,FER,PER,SUM Error flag UiBRG 0 to 7 Set a transfer rate UiMR SMD2 to SMD0 Set these bits to ‘1002’ when transfer data is 7 bits long Set these bits to ‘1012’ when transfer data is 8 bits long Set these bits to ‘1102’ when transfer data is 9 bits long UiC0 CKDIR Select the internal clock or external clock STPS Select the stop bit PRY, PRYE Select whether parity is included and whether odd or even IOPOL Select the TxD/RxD input/output polarity CLK0, CLK1 Select the count source for the UiBRG register CRS Select CTS or RTS to use TXEPT Transmit register empty flag CRD Enable or disable the CTS or RTS function NCH Select TxDi pin output mode (Note 2) CKPOL Set to “0” UFORM LSB first or MSB first can be selected when transfer data is 8 bits long. Set this _______ _______ _______ _______ bit to “0” when transfer data is 7 or 9 bits long. UiC1 TE Set this bit to “1” to enable transmission TI Transmit buffer empty flag RE Set this bit to “1” to enable reception RI Reception complete flag U2IRS (Note 2) Select the source of UART2 transmit interrupt U2RRM (Note 2) Set to “0” UiLCH Set this bit to “1” to use inverted data logic UiERE Set to “0” UiSMR 0 to 7 Set to “0” UiSMR2 0 to 7 Set to “0” UiSMR3 0 to 7 Set to “0” UiSMR4 0 to 7 Set to “0” UCON U0IRS, U1IRS Select the source of UART0/UART1 transmit interrupt U0RRM, U1RRM Set to “0” CLKMD0 Invalid because CLKMD1 = 0 CLKMD1 Set to “0” RCSP Set this bit to “1” to accept as input the UART0 CTS0 signal from the P64 pin 7 Set to “0” _________ Note 1: The bits used for transmit/receive data are as follows: Bit 0 to bit 6 when transfer data is 7 bits long; bit 0 to bit 7 when transfer data is 8 bits long; bit 0 to bit 8 when transfer data is 9 bits long. Note 2: Set the U0C1 and U1C1 registers bit 4 to bit 5 to “0”. The U0IRS, U1IRS, U0RRM and U1RRM bits are included in the UCON register. Note 3: TxD2 pin is N channel open-drain output. Set the U2C0 register's NCH bit to “0”. i=0 to 2 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 110 of 201 M16C/6S Group UART Mode Table 1.15.3 lists the functions of the input/output pins during UART mode. Table 1.15.4 lists the P64 pin functions during UART mode. Note that for a period from when the UARTi operation mode is selected to when transfer starts, the TxDi pin outputs an “H”. (If the N-channel open-drain output is selected, this pin is in a high-impedance state.) Table 1.15.3. I/O Pin Functions Pin name Function Method of selection TxDi (i = 0 to 2) Serial data output (P63, P67, P70) (Outputs dummy data when performing reception only) Serial data input RxDi (P62, P66, P71) PD6 register’s PD6_2 bit=0, PD6_6 bit=0, PD7 register’s PD7_1 bit=0 (Can be used as an input port when performing transmission only) CLKi (P61, P65) Input/output port UiMR register’s CKDIR bit=0 Transfer clock input UiMR register’s CKDIR bit=1 PD6 register’s PD6_1 bit=0, PD6_5 bit=0, PD7 register’s PD7_2 bit=0 CTSi/RTSi CTS input (P60, P64, P73) UiC0 register’s CRD bit=0 UiC0 register’s CRS bit=0 PD6 register’s PD6_0 bit=0, PD6_4 bit=0, PD7 register’s PD7_3 bit=0 RTS output UiC0 register’s CRD bit=0 UiC0 register’s CRS bit=1 Input/output port UiC0 register’s CRD bit=1 Table 1.15.4. P64 Pin Functions Pin function Bit set value U1C0 register CRS CRD P64 CTS1 RTS1 CTS0 (Note) 1 0 0 0 UCON register RCSP CLKMD1 0 1 0 0 0 0 1 0 0 0 0 PD6 register PD6_4 Input: 0, Output: 1 0 0 Note: In addition to this, set the U0C0 register’s CRD bit to “0” (CTS0/RTS0 enabled) and the U0C0 register’s CRS bit to “1” (RTS0 selected). Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 111 of 201 M16C/6S Group UART Mode (1) Example of transmit timing when transfer data is 8 bits long (parity enabled, one stop bit) The transfer clock stops momentarily as CTSi is “H” when the stop bit is checked. The transfer clock starts as the transfer starts immediately CTSi changes to “L”. Tc Transfer clock UiC1 register TE bit “1” “0” UiC1 register TI bit Write data to the UiTB register “1” “0” Transferred from UiTB register to UARTi transmit register “H” CTSi “L” Start bit TxDi UiC0 register TXEPT bit Stopped pulsing because the TE bit = “0” Parity Stop bit bit ST D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 “1” “0” SiTIC register IR bit “1” “0” Cleared to “0” when interrupt request is accepted, or cleared to “0” in a program The above timing diagram applies to the case where the register bits are set as follows: • UiMR register PRYE bit = 1 (parity enabled) • UiMR register STPS bit = 0 (1 stop bit) • UiC0 register CRD bit = 0 (CTS/RTS enabled), CRS bit = 0 (CTS selected) • UiRS bit = 1 (an interrupt request occurs when transmit completed): U0IRS bit is the UCON register bit 0, U1IRS bit is the UCON register bit 1, and U2IRS bit is the U2C1 register bit 4 Tc = 16 (n + 1) / fj or 16 (n + 1) / fEXT fj : frequency of UiBRG count source (f1SIO, f2SIO, f8SIO, f32SIO) fEXT : frequency of UiBRG count source (external clock) n : value set to UiBRG i: 0 to 2 (2) Example of transmit timing when transfer data is 9 bits long (parity disabled, two stop bits) Tc Transfer clock UiC1 register TE bit UiC1 register TI bit “1” Write data to the UiTB register “0” “1” “0” Start bit TxDi Stop Stop bit bit ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SP SP UiC0 register TXEPT bit “1” SiTIC register IR bit “1” Transferred from UiTB register to UARTi transmit register ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SPSP ST D0 D1 “0” “0” Cleared to “0” when interrupt request is accepted, or cleared to “0” in a program Tc = 16 (n + 1) / fj or 16 (n + 1) / fEXT The above timing diagram applies to the case where the register bits are set as follows: fj : frequency of UiBRG count source (f1SIO, f2SIO, f8SIO, f32SIO) • UiMR register PRYE bit = 0 (parity disabled) fEXT : frequency of UiBRG count source (external clock) • UiMR register STPS bit = 1 (2 stop bits) n : value set to UiBRG • UiC0 register CRD bit = 1 (CTS/RTS disabled) i: 0 to 2 • UiRS bit = 0 (an interrupt request occurs when transmit buffer becomes empty): U0IRS bit is the UCON register bit 0, U1IRS bit is the UCON register bit 1, and U2IRS bit is the U2C1 register bit 4 Figure 1.15.1. Transmit Operation Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 112 of 201 M16C/6S Group UART Mode • Example of receive timing when transfer data is 8 bits long (parity disabled, one stop bit) UiBRG count source UiC1 register RE bit “1” “0” Stop bit Start bit RxDi Sampled “L” D7 D1 D0 Receive data taken in Transfer clock UiC1 register RI bit RTSi SiRIC register IR bit Reception triggered when transfer clock “1” is generated by falling edge of start bit Transferred from UARTi receive register to UiRB register “0” “H” “L” “1” “0” Cleared to “0” when interrupt request is accepted, or cleared to “0” in a program The above timing diagram applies to the case where the register bits are set as follows: • UiMR register PRYE bit = 0 (parity disabled) • UiMR register STPS bit = 0 (1 stop bit) • UiC0 register CRD bit = 0 (CTSi/RTSi enabled), CRS bit = 1 (RTSi selected) i = 0 to 2 Figure 1.15.2. Receive Operation Bit Rates In UART mode, the frequency set by the UiBRG register (i=0 to 2) divided by 16 become the bit rates. Table 1.15.5 lists example of bit rates and settings. Table 1.15.5. Example of Bit Rates and Settings Bit Rate (bps) Count Source of BRG Peripheral Function Clock : 16MHz Set Value of BRG : n Actual Time (bps) Peripheral Function Clock : 24MHz Set value of BRG : n Actual Time (bps) 1200 f8 103 (67h) 1202 155 (96h) 1202 2400 f8 51 (33h) 2404 77 (46h) 2404 4800 f8 25 (19h) 4808 38 (26h) 4808 9600 f1 103 (67h) 9615 155 (96h) 9615 14400 f1 68 (44h) 14493 103 (67h) 14423 19200 f1 51 (33h) 19231 77 (46h) 19231 28800 f1 34 (22h) 28571 51 (33h) 28846 31250 f1 31 (1Fh) 31250 47 (2Fh) 31250 38400 f1 25 (19h) 38462 38 (26h) 38462 51200 f1 19 (13h) 50000 28 (1Ch) 51724 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 113 of 201 M16C/6S Group UART Mode Counter Measure for Communication Error Occurs If a communication error occurs while transmitting or receiving in UART mode, follow the procedures below. • Resetting the UiRB register (i=0 to 2) (1) Set the RE bit in the UiC1 register to “0” (reception disabled) (2) Set the RE bit in the UiC1 register to “1” (reception enabled) • Resetting the UiTB register (i=0 to 2) (1) Set the SMD2 to SMD0 bits in the UiMR register “000b” (Serial I/O disabled) (2) Set the SMD2 to SMD0 bits in the UiMR register “001b”, “101b”, “110b”. (3) “1” is written to RE bit in the UiC1 register (reception enabled), regardless of the TE bit in the UiCi register (a) LSB First/MSB First Select Function As shown in Figure 1.15.3, use the UiC0 register’s UFORM bit to select the transfer format. This function is valid when transfer data is 8 bits long. (1) When UiC0 register's UFORM bit = 0 (LSB first) CLKi TXDi ST D0 D1 D2 D3 D4 D5 D6 D7 P SP RXDi ST D0 D1 D2 D3 D4 D5 D6 D7 P SP (2) When UiC0 register's UFORM bit = 1 (MSB first) CLKi TXDi ST D7 D6 D5 D4 D3 D2 D1 D0 P SP RXDi ST D7 D6 D5 D4 D3 D2 D1 D0 P SP Note: This applies to the case where the UiC0 register’s CKPOL bit = 0 ( transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock), the UiC1 register’s UiLCH bit = 0 (no reverse), UiMR register's STPS bit = 0 (1 stop bit) and UiMR register's PRYE bit = 1 (parity enabled). Figure 1.15.3. Transfer Format Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 114 of 201 ST : Start bit P : Parity bit SP : Stop bit i = 0 to 2 M16C/6S Group UART Mode (b) Serial Data Logic Switching Function The data written to the UiTB register has its logic reversed before being transmitted. Similarly, the received data has its logic reversed when read from the UiRB register. Figure 1.15.4 shows serial data logic. (1) When the UiC1 register's UiLCH bit = 0 (no reverse) Transfer clock “H” “L” TxDi “H” (no reverse) “L” ST D0 D1 D2 D3 D4 D5 D6 D7 P SP D5 D6 D7 P SP (2) When the UiC1 register's UiLCH bit = 1 (reverse) Transfer clock “H” “L” TxDi “H” (reverse) “L” ST D0 D1 D2 D3 D4 Note: This applies to the case where the UiC0 register’s CKPOL bit = 0 ( transmit data output at the falling edge of the transfer clock), the UiC0 register's UFORM bit = 0 (LSB first), the UiMR register's STPS bit = 0 (1 stop bit) and UiMR register's PRYE bit = 1 (parity enabled). ST : Start bit P : Parity bit SP : Stop bit i = 0 to 2 Figure 1.15.4. Serial Data Logic Switching (c) TxD and RxD I/O Polarity Inverse Function This function inverses the polarities of the TXDi pin output and RXDi pin input. The logic levels of all input/output data (including the start, stop and parity bits) are inversed. Figure 1.15.5 shows the TXD pin output and RXD pin input polarity inverse. (1) When the UiMR register's IOPOL bit = 0 (no reverse) Transfer clock “H” “L” TxDi “H” (no reverse) “L” RxDi “H” (no reverse) “L” ST D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 D2 D3 D4 D5 D6 D7 P SP (2) When the UiMR register's IOPOL bit = 1 (reverse) Transfer clock “H” “L” TxDi “H” “L” ST D0 D1 D2 D3 D4 D5 D6 D7 P SP “H” “L” ST D0 D1 D2 D3 D4 D5 D6 D7 P SP (reverse) RxDi (reverse) Note: This applies to the case where the UiC0 register's UFORM bit = 0 (LSB first), the UiMR register's STPS bit = 0 (1 stop bit) and the UiMR register's PRYE bit = 1 (parity enabled). Figure 1.15.5. TXD and RXD I/O Polarity Inverse Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 115 of 201 ST : Start bit P : Parity bit SP : Stop bit i = 0 to 2 M16C/6S Group UART Mode _______ _______ CTS/RTS Function _______ ________ ________ When the CTS function is used transmit operation start when “L” is applied to the CTSi/RTSi (i=0 to 2) ________ ________ pin. Transmit operation begins when the CTSi/RTSi pin is held “L”. If the “L” signal is switched to “H” during a transmit operation, the operation stops before the next data. _______ ________ ________ When the RTS function is used, the CTSi/RTSi pin outputs on “L” signal when the microcomputer is ready to receive. The output level becomes “H” on the first falling edge of the CLKi pin. _______ _______ • CRD bit in UiC0 register = 1 (disable CTS/RTS function of UART0) ________ ________ CTSi/RTSi pin is programmable I/O function _______ ________ ________ _______ • CRD bit = 0, CRS bit = 0 (CTS function is selected) CTSi/RTSi pin is CTS function _______ ________ ________ _______ • CRD bit = 0, CRS bit = 1 (RTS function is selected) CTSi/RTSi pin is RTS function _______ _______ (d) CTS/RTS Separate Function (UART0) _______ _______ _______ _______ This function separates CTS0/RTS0, outputs RTS0 from the P60 pin, and accepts as input the CTS0 from the P64 pin. To use this function, set the register bits as shown below. _______ _______ • U0C0 register's CRD bit = 0 (enables UART0 CTS/RTS) _______ • U0C0 register's CRS bit = 1 (outputs UART0 RTS) _______ _______ • U1C0 register's CRD bit = 0 (enables UART1 CTS/RTS) _______ • U1C0 register's CRS bit = 0 (inputs UART1 CTS) _______ • UCON register's RCSP bit = 1 (inputs CTS0 from the P64 pin) • UCON register's CLKMD1 bit = 0 (CLKS1 not used) _______ _______ _______ _______ Note that when using the CTS/RTS separate function, UART1 CTS/RTS separate function cannot be used. IC Microcomputer TXD0 (P63) RXD0 (P62) IN OUT RTS0 (P60) CTS CTS0 (P64) RTS _______ _______ Figure 1.15.6. CTS/RTS Separate Function Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 116 of 201 M16C/6S Group Special Mode Special Mode 1 (I2C mode) I2C mode is provided for use as a simplified I2C interface compatible mode. Table 1.16.1 lists the specifications of the I2C mode. Table 1.16.2 lists the registers used in the I2C mode and the register values set. Figure 1.16.1 shows the block diagram for I2C mode. Figure 1.16.2 shows SCLi timing. As shown in Table 1.16.4, the microcomputer is placed in I2C mode by setting the SMD2 to SMD0 bits to ‘0102’ and the IICM bit to “1”. Because SDAi transmit output has a delay circuit attached, SDAi output does not change state until SCLi goes low and remains stably low. Table 1.16.1. I2C Mode Specifications Item Specification Transfer data format Transfer clock • Transfer data length: 8 bits • During master UiMR(i=0 to 2) register’s CKDIR bit = “0” (internal clock) : fj/ 2(n+1) fj = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of UiBRG register 0016 to FF16 • During slave CKDIR bit = “1” (external clock) : Input from CLKi pin Transmission start condition • Before transmission can start, the following requirements must be met (Note 1) _ The TE bit of UiC1 register= 1 (transmission enabled) _ The TI bit of UiC1 register = 0 (data present in UiTB register) Reception start condition • Before reception can start, the following requirements must be met (Note 1) _ The RE bit of UiC1 register= 1 (reception enabled) _ The TE bit of UiC1 register= 1 (transmission enabled) _ The TI bit of UiC1 register= 0 (data present in the UiTB register) Interrupt request When start or stop condition is detected, acknowledge undetected, and acknowledge generation timing detected Error detection • Overrun error (Note 2) This error occurs if the serial I/O started receiving the next data before reading the UiRB register and received the 8th bit of the data Select function • Arbitration lost Timing at which the UiRB register’s ABT bit is updated can be selected • SDAi digital delay No digital delay or a delay of 2 to 8 UiBRG count source clock cycles selectable • Clock phase setting With or without clock delay selectable Note 1: When an external clock is selected, the conditions must be met while the external clock is in the high state. Note 2: If an overrun error occurs, the value of UiRB register will be indeterminate. The IR bit of SiRIC register does not change. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 117 of 201 M16C/6S Group Special Mode Start and stop condition generation block SDAi STPSEL=1 Delay circuit SDASTSP SCLSTSP STPSEL=0 ACK=1 IICM2=1 Transmission register ACK=0 IICM=1 and IICM2=0 UARTi SDHI ACKD register UARTi transmit, NACK interrupt request ALS DMA0 (UART0, UART2) Arbitration D Q T Noise Filter DMA0, DMA1 request (UART1: DMA0 only) IICM2=1 Reception register UARTi IICM=1 and IICM2=0 Start condition detection S R Q Bus busy Stop condition detection NACK D Q T Falling edge detection SCLi IICM=0 R I/O port Q STPSEL=0 IICM=1 UARTi UARTi receive, ACK interrupt request, DMA1 request D Q T Port register (Note) Internal clock STPSEL=1 Noise Filter SWC2 External clock R S ACK 9th bit Start/stop condition detection interrupt request CLK control UARTi 9th bit falling edge SWC This diagram applies to the case where the UiMR register's SMD2 to SMD0 bits = 0102 and the UiSMR register's IICM bit = 1. IICM : Bit in UiSMR register IICM2, SWC, ALS, SWC2, SDHI : Bit in UiSMR2 register STSPSEL, ACKD, ACKC : Bit in UiSMR4 register i=0 to 2 Note: When the IICM bit =1, the pins can be read even if the direction bit = 1 (output). Figure 1.16.1. I2C Mode Block Diagram Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 118 of 201 M16C/6S Group Special Mode Table 1.16.2. Registers to Be Used and Settings in I2C Mode (1) (Continued) Register UiTB3 UiRB3 UiBRG UiMR3 UiC0 UiC1 UiSMR Bit 0 to 7 0 to 7 8 ABT OER 0 to 7 SMD2 to SMD0 CKDIR IOPOL CLK1, CLK0 CRS TXEPT CRD NCH CKPOL UFORM TE TI RE RI U2IRS1 U2RRM1, UiLCH, UiERE IICM ABC BBS 3 to 7 UiSMR2 IICM2 CSC SWC ALS STAC Function Master Slave Set transmission data Set transmission data Reception data can be read Reception data can be read ACK or NACK is set in this bit ACK or NACK is set in this bit Arbitration lost detection flag Invalid Overrun error flag Overrun error flag Set a transfer rate Invalid Set to ‘0102’ Set to ‘0102’ Set to “0” Set to “1” Set to “0” Set to “0” Select the count source for the UiBRG Invalid register Invalid because CRD = 1 Invalid because CRD = 1 Transmit buffer empty flag Transmit buffer empty flag Set to “1” Set to “1” Set to “1”2 Set to “1”2 Set to “0” Set to “0” Set to “1” Set to “1” Set this bit to “1” to enable transmission Set this bit to “1” to enable transmission Transmit buffer empty flag Transmit buffer empty flag Set this bit to “1” to enable reception Set this bit to “1” to enable reception Reception complete flag Reception complete flag Invalid Invalid Set to “0” Set to “0” Set to “1” Select the timing at which arbitration-lost is detected Bus busy flag Set to “0” Refer to Table 1.16.4. Set this bit to “1” to enable clock synchronization Set this bit to “1” to have SCLi output fixed to “L” at the falling edge of the 9th bit of clock Set this bit to “1” to have SDAi output stopped when arbitration-lost is detected Set to “0” SWC2 Set this bit to “1” to have SCLi output forcibly pulled low SDHI Set this bit to “1” to disable SDAi output 7 Set to “0” UiSMR3 0, 2, 4 and NODC Set to “0” CKPH Refer to Table 1.16.4 DL2 to DL0 Set the amount of SDAi digital delay Set to “1” Invalid Bus busy flag Set to “0” Refer to Table 1.16.4. Set to “0” Set this bit to “1” to have SCLi output fixed to “L” at the falling edge of the 9th bit of clock Set to “0” Set this bit to “1” to initialize UARTi at start condition detection Set this bit to “1” to have SCLi output forcibly pulled low Set this bit to “1” to disable SDAi output Set to “0” Set to “0” Refer to Table 1.16.4 Set the amount of SDAi digital delay i=0 to 2 Notes: 1. Set the U0C1 and U1C1 register bit 4 and bit 5 to “0”. The U0IRS, U1IRS, U0RRM and U1RRM bits are in the UCON register. 2. TxD2 pin is N channel open-drain output. Set the NCH bit in the U2C0 register to “0”. 3. Not all register bits are described above. Set those bits to “0” when writing to the registers in I2C mode. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 119 of 201 M16C/6S Group Special Mode Table 1.16.3. Registers to Be Used and Settings in I2C Mode (2) (Continued) Register Bit UiSMR4 STAREQ RSTAREQ STPREQ STSPSEL ACKD ACKC SCLHI SWC9 IFSR2A IFSR26, ISFR27 UCON U0IRS, U1IRS 2 to 7 Function Master Slave Set this bit to “1” to generate start Set to “0” condition Set this bit to “1” to generate restart Set to “0” condition Set this bit to “1” to generate stop Set to “0” condition Set this bit to “1” to output each condition Set to “0” Select ACK or NACK Select ACK or NACK Set this bit to “1” to output ACK data Set this bit to “1” to output ACK data Set this bit to “1” to have SCLi output Set to “0” stopped when stop condition is detected Set to “0” Set this bit to “1” to set the SCLi to “L” hold at the falling edge of the 9th bit of clock Set to “1” Set to “1” Invalid Invalid Set to “0” Set to “0” i=0 to 2 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 120 of 201 M16C/6S Group Special Mode Table 1.16.4. I2C Mode Functions Function Clock Synchronous Serial I/O I2C Mode (SMD2 to SMD0 = 010b, IICM = 1) Mode (SMD2 to SMD0 = 001b, IICM2 = 0 IICM2 = 1 IICM = 0) (NACK/ACK interrupt) (UART transmit/ receive interrupt) CKPH = 1 CKPH = 0 CKPH = 0 CKPH = 1 (Clock delay) (No clock delay) (Clock delay) (No clock delay) Factor of Interrupt Number 6, 7 and 10 (1, 5, 7) Start condition detection or stop condition detection (See Table 1.16.5 STSPSEL Bit Functions) Factor of Interrupt Number UARTi transmission 15, 17 and 19 (1, 6) Transmission started or completed (selected by UiIRS) Factor of Interrupt Number UARTi reception When 8th bit received 16, 18 and 20 (1, 6) CKPOL = 0 (rising edge) CKPOL = 1 (falling edge) Timing for Transferring CKPOL = 0 (rising edge) Data From the UART CKPOL = 1 (falling edge) Reception Shift Register to the UiRB Register UARTi Transmission Not delayed Output Delay No acknowledgment detection (NACK) Rising edge of SCLi 9th bit Acknowledgment detection (ACK) Rising edge of SCLi 9th bit Rising edge of SCLi 9th bit UARTi transmission UARTi transmission Falling edge of SCLi Rising edge of next to the 9th bit SCLi 9th bit UARTi reception Falling edge of SCLi 9th bit Falling edge of SCLi 9th bit Falling and rising edges of SCLi 9th bit Delayed Functions of P6_3, P6_7 and P7_0 Pins TXDi output SDAi input/output Functions of P6_2, P6_6 and P7_1 Pins RXDi input SCLi input/output Functions of P6_1, P6_5 and P7_2 Pins CLKi input or output selected (Cannot be used in I2C mode) 200ns Noise Filter Width 15ns Read RXDi and SCLi Pin Levels Always possible no matter how the corresponding port direction bit is set Possible when the corresponding port direction bit =0 CKPOL = 0 (H) The value set in the port register before setting I2C mode (2) CKPOL = 1 (L) Initial Value of TXDi and SDAi Outputs Initial and End Values of SCLi H L H L DMA1 Factor (6) UARTi reception Acknowledgment detection (ACK) Store Received Data 1st to 8th bits of the received data are stored into bits 7 to 0 in the UiRB register 1st to 8th bits of the received 1st to 7th bits of the received data are data are stored into bits 7 to 0 stored into bits 6 to 0 in the UiRB register. 8th bit is stored into bit 8 in the in the UiRB register UiRB register. Read Received Data The UiRB register status is read UARTi reception Falling edge of SCLi 9th bit 1st to 8th bits are stored into bits 7 to 0 in the UiRB register (3) Bits 6 to 0 in the UiRB register (4) are read as bits 7 to 1. Bit 8 in the UiRB register is read as bit 0. i = 0 to 2 NOTES : 1. If the source or cause of any interrupt is changed, the IR bit in the interrupt control register for the changed interrupt may inadvertently be set to “1” (interrupt requested). (Refer to Changing the Interrupt Generate Factor.) If one of the bits shown below is changed, the interrupt source, the interrupt timing, etc. change. Therefore, always be sure to clear the IR bit to “0” (interrupt not requested) after changing those bits. SMD2 to SMD0 bits in the UiMR register, IICM bit in the UiSMR register, IICM2 bit in the UiSMR2 register, CKPH bit in the UiSMR3 register 2. Set the initial value of SDAi output while the SMD2 to SMD0 bits in the UiMR register = 000b (serial I/O disabled). 3. Second data transfer to UiRB register (Rising edge of SCLi 9th bit) 4. First data transfer to UiRB register (Falling edge of SCLi 9th bit) 5. See Figure 1.16.4 STSPSEL Bit Functions. 6. See Figure 1.16.2 Transfer to UiRB Register and Interrupt Timing. 7. When using UART0, be sure to set the IFSR26 bit in the IFSR2A register to “1” (factor of interrupt: UART0 bus collision). When using UART1, be sure to set the IFSR27 bit to “1” (factor of interrupt: UART1 bus collision). Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 121 of 201 M16C/6S Group Special Mode (1) IICM2= 0 (ACK and NACK interrupts), CKPH= 0 (no clock delay) 1st bit 2nd bit 3rd bit 4th bit 5th bit 6th bit 7th bit 8th bit 9th bit SCLi SDAi D7 D6 D5 D4 D3 D2 D1 D0 D8 (ACK, NACK) ACK interrupt (DMA1 request), NACK interrupt Transfer to UiRB register b15 b9 ••• b8 b7 D8 D7 b0 D6 D5 D4 D3 D2 D1 D0 D2 D1 D0 D3 D2 D1 UiRB register (2) IICM2= 0, CKPH= 1 (clock delay) 1st bit 2nd bit 3rd bit 4th bit 5th bit 6th bit 7th bit 8th bit 9th bit SCLi SDAi D7 D6 D5 D4 D3 D2 D1 D0 D8 (ACK, NACK) ACK interrupt (DMA1 request), NACK interrupt Transfer to UiRB register b15 b9 ••• b8 b7 D8 D7 b0 D6 D5 D4 D3 UiRB register (3) IICM2= 1 (UART transmit/receive interrupt), CKPH= 0 1st bit 2nd bit 3rd bit 4th bit 5th bit 6th bit 7th bit 8th bit 9th bit SCLi SDAi D7 D6 D5 D4 D3 D2 D1 D0 D8 (ACK, NACK) Receive interrupt (DMA1 request) Transmit interrupt Transfer to UiRB register b15 b9 b8 b7 b0 D0 ••• D7 D6 D5 D4 UiRB register (4) IICM2= 1, CKPH= 1 1st bit 2nd bit 3rd bit 4th bit 5th bit 6th bit 7th bit 8th bit 9th bit SCLi SDAi D7 D6 D5 D4 D3 D2 D1 D0 D8 (ACK, NACK) Receive interrupt (DMA1 request) Transfer to UiRB register b15 b9 ••• b8 D0 b7 b0 D7 D6 D5 D4 D3 D2 D1 Transmit interrupt Transfer to UiRB register b15 b9 ••• UiRB register i=0 to 2 This diagram applies to the case where the following condition is met. • UiMR register CKDIR bit = 0 (Slave selected) Figure 1.16.2. Transfer to UiRB Register and Interrupt Timing Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 122 of 201 b8 b7 D8 D7 b0 D6 D5 D4 D3 D2 UiRB register D1 D0 M16C/6S Group Special Mode • Detection of Start and Stop Condition Whether a start or a stop condition has been detected is determined. A start condition-detected interrupt request is generated when the SDAi pin changes state from high to low while the SCLi pin is in the high state. A stop condition-detected interrupt request is generated when the SDAi pin changes state from low to high while the SCLi pin is in the high state. Because the start and stop condition-detected interrupts share the interrupt control register and vector, check the UiSMR register’s BBS bit to determine which interrupt source is requesting the interrupt. 3 to 6 cycles < duration for setting-up (Note) 3 to 6 cycles < duration for holding (Note) Duration for setting up Duration for holding SCLi SDAi (Start condition) SDA i (Stop condition) i = 0 to 2 Note: When the PCLKR register's PCLK1 bit = 1, this is the cycle number of f1SIO, and the PCLK1 bit = 0, this is the cycle number of f2SIO. Figure 1.16.3. Detection of Start and Stop Condition • Output of Start and Stop Condition A start condition is generated by setting the STAREQ bit in the UiSMR4 register (i = 0 to 2) to “1” (start). A restart condition is generated by setting the RSTAREQ bit in the UiSMR4 register to “1” (start). A stop condition is generated by setting the STPREQ bit in the UiSMR4 register to “1” (start). The output procedure is described below. (1) Set the STAREQ bit, RSTAREQ bit or STPREQ bit to “1” (start). (2) Set the STSPSEL bit in the UiSMR4 register to “1” (output). The function of the STSPSEL bit is shown in Table 1.16.5 and Figure 1.16.4. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 123 of 201 M16C/6S Group Special Mode Table 1.16.5. STSPSEL Bit Functions Function Output of SCLi and SDAi pins Star/stop condition interrupt request generation timing STSPSEL = 0 Output of transfer clock and data Output of start/stop condition is accomplished by a program using ports (not automatically generated in hardware) Start/stop condition detection STSPSEL = 1 Output of a start/stop condition according to the STAREQ, RSTAREQ and STPREQ bit Finish generating start/stop condition (1) When slave CKDIR=1 (external clock) STPSEL bit 0 1st 2nd 3rd 4th 5th 6th 7th 8th 9th bit SCLi SDAi Start condition detection interrupt Stop condition detection interrupt (2) When master CKDIR=0 (internal clock), CKPH=1 (clock delayed) STPSEL bit Set to “1” in a program Set to “0” in a program Set to “1” in a program Set to “0” in a program 1st 2nd 3rd 4th 5th 6th 7th 8th 9th bit SCLi SDAi Set STAREQ= 1 (start) Start condition detection interrupt Set STPREQ= 1 (start) Stop condition detection interrupt Figure 1.16.4. STSPSEL Bit Functions • Arbitration Unmatching of the transmit data and SDAi pin input data is checked synchronously with the rising edge of SCLi. Use the UiSMR register’s ABC bit to select the timing at which the UiRB register’s ABT bit is updated. If the ABC bit = 0 (updated bitwise), the ABT bit is set to “1” at the same time unmatching is detected during check, and is cleared to “0” when not detected. In cases when the ABC bit is set to “1”, if unmatching is detected even once during check, the ABT bit is set to “1” (unmatching detected) at the falling edge of the clock pulse of 9th bit. If the ABT bit needs to be updated bytewise, clear the ABT bit to “0” (undetected) after detecting acknowledge in the first byte, before transferring the next byte. Setting the UiSMR2 register’s ALS bit to “1” (SDA output stop enabled) causes arbitration-lost to occur, in which case the SDAi pin is placed in the high-impedance state at the same time the ABT bit is set to “1” (unmatching detected). Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 124 of 201 M16C/6S Group Special Mode • Transfer Clock Data is transmitted/received using a transfer clock like the one shown in Figure 1.16.4. The UiSMR2 register’s CSC bit is used to synchronize the internally generated clock (internal SCLi) and an external clock supplied to the SCLi pin. In cases when the CSC bit is set to “1” (clock synchronization enabled), if a falling edge on the SCLi pin is detected while the internal SCLi is high, the internal SCLi goes low, at which time the UiBRG register value is reloaded with and starts counting in the low-level interval. If the internal SCLi changes state from low to high while the SCLi pin is low, counting stops, and when the SCLi pin goes high, counting restarts. In this way, the UARTi transfer clock is comprised of the logical product of the internal SCLi and SCLi pin signal. The transfer clock works from a half period before the falling edge of the internal SCLi 1st bit to the rising edge of the 9th bit. To use this function, select an internal clock for the transfer clock. The UiSMR2 register’s SWC bit allows to select whether the SCLi pin should be fixed to or freed from low-level output at the falling edge of the 9th clock pulse. If the UiSMR4 register’s SCLHI bit is set to “1” (enabled), SCLi output is turned off (placed in the highimpedance state) when a stop condition is detected. Setting the UiSMR2 register’s SWC2 bit = 1 (0 output) makes it possible to forcibly output a low-level signal from the SCLi pin even while sending or receiving data. Clearing the SWC2 bit to “0” (transfer clock) allows the transfer clock to be output from or supplied to the SCLi pin, instead of outputting a low-level signal. If the UiSMR4 register’s SWC9 bit is set to “1” (SCL hold low enabled) when the UiSMR3 register’s CKPH bit = 1, the SCLi pin is fixed to low-level output at the falling edge of the clock pulse next to the ninth. Setting the SWC9 bit = 0 (SCL hold low disabled) frees the SCLi pin from low-level output. • SDA Output The data written to the UiTB register bit 7 to bit 0 (D7 to D0) is sequentially output beginning with D7. The ninth bit (D8) is ACK or NACK. The initial value of SDAi transmit output can only be set when IICM = 1 (I2C mode) and the UiMR register’s SMD2 to SMD0 bits = ‘0002’ (serial I/O disabled). The UiSMR3 register’s DL2 to DL0 bits allow to add no delays or a delay of 2 to 8 UiBRG count source clock cycles to SDAi output. Setting the UiSMR2 register’s SDHI bit = 1 (SDA output disabled) forcibly places the SDAi pin in the high-impedance state. Do not write to the SDHI bit synchronously with the rising edge of the UARTi transfer clock. This is because the ABT bit may inadvertently be set to “1” (detected). • SDA Input When the IICM2 bit = 0, the 1st to 8th bits (D7 to D0) of received data are stored in the UiRB register bit 7 to bit 0. The 9th bit (D8) is ACK or NACK. When the IICM2 bit = 1, the 1st to 7th bits (D7 to D1) of received data are stored in the UiRB register bit 6 to bit 0 and the 8th bit (D0) is stored in the UiRB register bit 8. Even when the IICM2 bit = 1, providing the CKPH bit = 1, the same data as when the IICM2 bit = 0 can be read out by reading the UiRB register after the rising edge of the corresponding clock pulse of 9th bit. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 125 of 201 M16C/6S Group Special Mode • ACK and NACK If the STSPSEL bit in the UiSMR4 register is set to “0” (start and stop conditions not generated) and the ACKC bit in the UiSMR4 register is se to “1” (ACK data output), the value of the ACKD bit in the UiSMR4 register is output from the SDAi pin. If the IICM2 bit = 0, a NACK interrupt request is generated if the SDAi pin remains high at the rising edge of the 9th bit of transmit clock pulse. An ACK interrupt request is generated if the SDAi pin is low at the rising edge of the 9th bit of transmit clock pulse. If ACKi is selected for the cause of DMA1 request, a DMA transfer can be activated by detection of an acknowledge. • Initialization of Transmission/Reception If a start condition is detected while the STAC bit = 1 (UARTi initialization enabled), the serial I/O operates as described below. - The transmit shift register is initialized, and the content of the UiTB register is transferred to the transmit shift register. In this way, the serial I/O starts sending data synchronously with the next clock pulse applied. However, the UARTi output value does not change state and remains the same as when a start condition was detected until the first bit of data is output synchronously with the input clock. - The receive shift register is initialized, and the serial I/O starts receiving data synchronously with the next clock pulse applied. - The SWC bit is set to “1” (SCL wait output enabled). Consequently, the SCLi pin is pulled low at the falling edge of the ninth clock pulse. Note that when UARTi transmission/reception is started using this function, the TI does not change state. Note also that when using this function, the selected transfer clock should be an external clock. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 126 of 201 M16C/6S Group Special Mode Special Mode 2 Multiple slaves can be serially communicated from one master. Synchronous clock polarity and phase are selectable. Table 1.16.6 lists the specifications of Special Mode 2. Table 1.16.7 lists the registers used in Special Mode 2 and the register values set. Figure 1.16.5 shows communication control example for Special Mode 2. UART2 is not available in this mode. Table 1.16.6. Special Mode 2 Specifications Item Specification Transfer data format Transfer clock • Transfer data length: 8 bits • Master mode UiMR(i=0 to 1) register’s CKDIR bit = “0” (internal clock) : fj/ 2(n+1) fj = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of UiBRG register 0016 to FF16 • Slave mode CKDIR bit = “1” (external clock selected) : Input from CLKi pin Transmit/receive control Controlled by input/output ports Transmission start condition • Before transmission can start, the following requirements must be met (Note 1) _ The TE bit of UiC1 register= 1 (transmission enabled) _ The TI bit of UiC1 register = 0 (data present in UiTB register) Reception start condition • Before reception can start, the following requirements must be met (Note 1) _ The RE bit of UiC1 register= 1 (reception enabled) _ The TE bit of UiC1 register= 1 (transmission enabled) _ The TI bit of UiC1 register= 0 (data present in the UiTB register) Interrupt request • For transmission, one of the following conditions can be selected _ The UiIRS bit of UiC1 register = 0 (transmit buffer empty): when transferring data generation timing from the UiTB register to the UARTi transmit register (at start of transmission) _ The UiIRS bit =1 (transfer completed): when the serial I/O finished sending data from the UARTi transmit register • For reception When transferring data from the UARTi receive register to the UiRB register (at completion of reception) Error detection • Overrun error (Note 2) This error occurs if the serial I/O started receiving the next data before reading the UiRB register and received the 7th bit of the next data Select function • Clock phase setting Selectable from four combinations of transfer clock polarities and phases Note 1: When an external clock is selected, the conditions must be met while if the UiC0 register’s CKPOL bit = “0” (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock), the external clock is in the high state; if the UiC0 register’s CKPOL bit = “1” (transmit data output at the rising edge and the receive data taken in at the falling edge of the transfer clock), the external clock is in the low state. Note 2: If an overrun error occurs, the value of UiRB register will be indeterminate. The IR bit of SiRIC register does not change. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 127 of 201 M16C/6S Group Special Mode P81 P80 P83 P61(CLK0) P61(CLK0) P62(RxD0) P62(RxD0) P63(TxD0) P63(TxD0) Microcomputer (Master) Microcomputer (Slave) P93 P61(CLK0) P62(RxD0) P63(TxD0) Microcomputer (Slave) Figure 1.16.5. Serial Bus Communication Control Example (UART0) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 128 of 201 M16C/6S Group Special Mode Table 1.16.7. Registers to Be Used and Settings in Special Mode 2 Register Bit UiTB(Note2) 0 to 7 UiRB(Note2) 0 to 7 OER UiBRG 0 to 7 UiMR(Note2) SMD2 to SMD0 CKDIR IOPOL UiC0 CLK1, CLK0 CRS TXEPT CRD NCH CKPOL UFORM UiC1 TE TI RE RI U2IRS (Note 1) U2RRM(Note 1), U2LCH, UiERE UiSMR 0 to 7 UiSMR2 0 to 7 UiSMR3 CKPH NODC 0, 2, 4 to 7 UiSMR4 0 to 7 UCON U0IRS, U1IRS U0RRM, U1RRM CLKMD0 CLKMD1, RCSP, 7 Function Set transmission data Reception data can be read Overrun error flag Set a transfer rate Set to ‘0012’ Set this bit to “0” for master mode or “1” for slave mode Set to “0” Select the count source for the UiBRG register Invalid because CRD = 1 Transmit register empty flag Set to “1” Select TxDi pin output format Clock phases can be set in combination with the UiSMR3 register's CKPH bit Set to “0” Set this bit to “1” to enable transmission Transmit buffer empty flag Set this bit to “1” to enable reception Reception complete flag Select UART2 transmit interrupt cause Set to “0” Set to “0” Set to “0” Clock phases can be set in combination with the UiC0 register's CKPOL bit Set to “0” Set to “0” Set to “0” Select UART0 and UART1 transmit interrupt cause Set to “0” Invalid because CLKMD1 = 0 Set to “0” Note 1: Set the U0C0 and U1C1 register bit 4 and bit 5 to “0”. The U0IRS, U1IRS, U0RRM and U1RRM bits are in the UCON register. Note 2: Not all register bits are described above. Set those bits to “0” when writing to the registers in Special Mode 2. i = 0 to 1 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 129 of 201 M16C/6S Group Special Mode • Clock Phase Setting Function One of four combinations of transfer clock phases and polarities can be selected using the UiSMR3 register’s CKPH bit and the UiC0 register’s CKPOL bit. Make sure the transfer clock polarity and phase are the same for the master and salves to be communicated. Figure 1.16.6 shows the transmission and reception timing in master (internal clock). Figure 1.16.7 shows the transmission and reception timing (CKPH=0) in slave (external clock) while Figure 1.16.8 shows the transmission and reception timing (CKPH=1) in slave (external clock). "H" Clock output (CKPOL=0, CKPH=0) "L" "H" Clock output (CKPOL=1, CKPH=0) "L" Clock output "H" (CKPOL=0, CKPH=1) "L" "H" Clock output (CKPOL=1, CKPH=1) "L" Data output timing "H" "L" D0 D1 D2 D3 D4 D5 D6 D7 Data input timing Figure 1.16.6. Transmission and Reception Timing in Master Mode (Internal Clock) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 130 of 201 M16C/6S Group Special Mode "H" Slave control input "L" "H" Clock input (CKPOL=0, CKPH=0) "L" "H" Clock input (CKPOL=1, CKPH=0) "L" Data output timing "H" (Note) "L" Data input timing D0 D1 D2 D3 D4 D5 D6 D7 Indeterminate Figure 1.16.7. Transmission and Reception Timing (CKPH=0) in Slave Mode (External Clock) "H" Slave control input "L" "H" Clock input (CKPOL=0, CKPH=1) "L" "H" Clock input (CKPOL=1, CKPH=1) "L" Data output timing (Note) "H" "L" D0 D1 D2 D3 D4 D5 D6 D7 Data input timing Figure 1.16.8. Transmission and Reception Timing (CKPH=1) in Slave Mode (External Clock) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 131 of 201 M16C/6S Group SI/O3 and SI/O4 SI/O3 and SI/O4 SI/O3 and SI/O4 are exclusive clock-synchronous serial I/Os. Figure 1.17.1 shows the block diagram of SI/O3 and SI/O4, and Figure 1.17.2 shows the SI/O3 and SI/O4related registers. SI/O4 is derectly connected to IT800 internally. Table 1.17.1 shows the specifications of SI/O3 and SI/O4. 1/2 f2SIO Clock source select SMi1 to SMi0 002 PCLK1=0 f1SIO Main clock, or On-chip Oscillator clock 1/8 PCLK1=1 1/4 f8SIO 012 f32SIO 102 Synchronous circuit SMi4 CLKi CLK polarity reversing circuit Data bus 1/(n+1) 1/2 SiBRG register SMi3 SMi6 SMi6 SI/O counter i SMi2 SMi3 SOUTi SMi5 LSB MSB SiTRR register SINi 8 Note: i = 3, 4. n = A value set in the SiBRG register. Figure 1.17.1. SI/O3 and SI/O4 Block Diagram Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 132 of 201 SI/Oi interrupt request M16C/6S Group SI/O3 and SI/O4 S I/Oi control register (i = 3, 4) (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol S3C S4C Bit symbol SMi0 Address 036216 036616 After reset 010000016 010000016 Description Bit name Internal synchronous clock select bit SMi1 b1 b0 0 0 : Selecting f1SIO or f2SIO 0 1 : Selecting f8SIO 1 0 : Selecting f32SIO 1 1 : Must not be set. RW RW RW SMi2 SOUTi output disable bit (Note 4) 0 : SOUTi output 1 : SOUTi output disable(high impedance) RW SMi3 S I/Oi port select bit 0 : Input/output port 1 : SOUTi output, CLKi function RW SMi4 CLK polarity select bit 0 : Transmit data is output at falling edge of transfer clock and receive data is input at rising edge 1 : Transmit data is output at rising edge of transfer clock and receive data is input at falling edge RW SMi5 Transfer direction select bit 0 : LSB first 1 : MSB first RW SMi6 Synchronous clock select bit 0 : External clock (Note 2) 1 : Internal clock (Note 3) RW SMi7 SOUTi initial value set bit Effective when SMi3 = 0 0 : “L” output 1 : “H” output RW Note 1: Make sure this register is written to by the next instruction after setting the PRCR register's PRC2 bit to “1” (write enable). Note 2: Set the SMi3 bit to “1” (SOUTi output, CLKi function). Note 3: Set the SMi3 bit to “1” and the corresponding port direction bit to “0” (input mode). Note 4: Effective when SMi3 bit = 1. SI/Oi bit rate generator (i = 3, 4) (Notes 1, 2) b7 b0 Symbol S3BRG S4BRG Address 036316 036716 After reset Indeterminate Indeterminate Description Setting range RW 0016 to FF16 WO Assuming that set value = n, BRGi divides the count source by n + 1 Note 1: Write to this register while serial I/O is neither transmitting nor receiving. Note 2: Use MOV instruction to write to this register. SI/Oi transmit/receive register (i = 3, 4) (Note 1, 2) b7 b0 Symbol S3TRR S4TRR Address 036016 036416 After reset Indeterminate Indeterminate Description RW Transmission/reception starts by writing transmit data to this register. After transmission/reception finishes, reception data can be read by reading this register. RW Note 1: Write to this register while serial I/O is neither transmitting nor receiving. Note 2: To receive data, set the corresponding port direction bit for SINi to “0” (input mode). Figure 1.17.2. S3C and S4C Registers, S3BRG and S4BRG Registers, and S3TRR and S4TRR Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 133 of 201 M16C/6S Group SI/O3 and SI/O4 Table 1.17.1. SI/O3 and SI/O4 Specifications Item Transfer data format Transfer clock Transmission/reception start condition Interrupt request generation timing Specification • Transfer data length: 8 bits • SiC (i=3, 4) register’s SMi6 bit = “1” (internal clock) : fj/ 2(n+1) fj = f1SIO, f8SIO, f32SIO. n=Setting value of SiBRG register 0016 to FF16. • SMi6 bit = “0” (external clock) : Input from CLKi pin (Note 1) • Before transmission/reception can start, the following requirements must be met Write transmit data to the SiTRR register (Notes 2, 3) • When SiC register's SMi4 bit = 0 The rising edge of the last transfer clock pulse (Note 4) • When SMi4 = 1 The falling edge of the last transfer clock pulse (Note 4) CLKi pin function SOUTi pin function SINi pin function Select function I/O port, transfer clock input, transfer clock output I/O port, transmit data output, high-impedance I/O port, receive data input • LSB first or MSB first selection Whether to start sending/receiving data beginning with bit 0 or beginning with bit 7 can be selected • Function for setting an SOUTi initial value set function When the SiC register's SMi6 bit = 0 (external clock), the SOUTi pin output level while not transmitting can be selected. • CLK polarity selection Whether transmit data is output/input timing at the rising edge or falling edge of transfer clock can be selected. Note 1: To set the SiC register’s SMi6 bit to “0” (external clock), follow the procedure described below. • If the SiC register’s SMi4 bit = 0, write transmit data to the SiTRR register while input on the CLKi pin is high. The same applies when rewriting the SiC register’s SMi7 bit. • If the SMi4 bit = 1, write transmit data to the SiTRR register while input on the CLKi pin is low. The same applies when rewriting the SMi7 bit. • Because shift operation continues as long as the transfer clock is supplied to the SI/Oi circuit, stop the transfer clock after supplying eight pulses. If the SMi6 bit = 1 (internal clock), the transfer clock automatically stops. Note 2: Unlike UART0 to UART2, SI/Oi (i = 3 to 4) is not separated between the transfer register and buffer. Therefore, do not write the next transmit data to the SiTRR register during transmission. Note 3: When the SiC register’s SMi6 bit = 1 (internal clock), SOUTi retains the last data for a 1/2 transfer clock period after completion of transfer and, thereafter, goes to a high-impedance state. However, if transmit data is written to the SiTRR register during this period, SOUTi immediately goes to a high-impedance state, with the data hold time thereby reduced. Note 4: When the SiC register’s SMi6 bit = 1 (internal clock), the transfer clock stops in the high state if the SMi4 bit = 0, or stops in the low state if the SMi4 bit = 1. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 134 of 201 M16C/6S Group SI/O3 and SI/O4 (a) SI/Oi Operation Timing Figure 1.17.3 shows the SI/Oi operation timing 1.5 cycle (max) (Note 3) SI/Oi internal clock "H" "L" CLKi output "H" "L" Signal written to the SiTRR register "H" "L" (Note 2) SOUTi output "H" "L" SINi input "H" "L" SiIC register IR bit "1" "0" D0 D1 D2 D3 D4 D5 D6 D7 i= 3, 4 Note 1: This diagram applies to the case where the SiC register bits are set as follows: SMi2=0 (SOUTi output), SMi3=1 (SOUTi output, CLKi function), SMi4=0 (transmit data output at the falling edge and receive data input at the rising edge of the transfer clock), SMi5=0 (LSB first) and SMi6=1 (internal clock) Note 2: When the SMi6 bit = 1 (internal clock), the SOUTi pin is placed in the high-impedance state after the transfer finishes. Note 3: If the SMi6 bit=0 (internal clock), the serial I/O starts sending or receiving data a maximum of 1.5 transfer clock cycles after writing to the SiTRR register. Figure 1.17.3. SI/Oi Operation Timing (b) CLK Polarity Selection The SiC register's SMi4 bit allows selection of the polarity of the transfer clock. Figure 1.17.4 shows the polarity of the transfer clock. (1) When SiC register's SMi4 bit = “0” (Note 2) CLKi SINi D0 D1 D2 D3 D4 D5 D6 D7 SOUTi D0 D1 D2 D3 D4 D5 D6 D7 (2) When SiC register's SMi4 bit = “1” (Note 3) CLKi SINi D0 D1 D2 D3 D4 D5 D6 D7 SOUTi D0 D1 D2 D3 D4 D5 D6 D7 i=3 and 4 Note 1: This diagram applies to the case where the SiC register bits are set as follows: SMi5=0 (LSB first) and SMi6=1 (internal clock) Note 2: When the SMi6 bit=1 (internal clock), a high level is output from the CLKi pin if not transferring data. Note 3: When the SMi6 bit=1 (internal clock), a low level is output from the CLKi pin if not transferring data. Figure 1.17.4. Polarity of Transfer Clock Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 135 of 201 M16C/6S Group SI/O3 and SI/O4 (c) Functions for Setting an SOUTi Initial Value If the SiC register’s SMi6 bit = 0 (external clock), the SOUTi pin output can be fixed high or low when not transferring. Figure 1.17.5 shows the timing chart for setting an SOUTi initial value and how to set it. (Example) When “H” selected for SOUTi initial value (Note 1) Setting of the initial value of SOUTi output and starting of transmission/ reception Signal written to SiTRR register SMi7 bit Set the SMi3 bit to “0” (SOUTi pin functions as an I/O port) SMi3 bit Set the SMi7 bit to “1” (SOUTi initial value = “H”) D0 SOUTi (internal) D0 Port output SOUTi pin output Initial value = “H” (Note 3) Set the SMi3 bit to “1” (SOUTi pin functions as SOUTi output) “H” level is output from the SOUTi pin (i = 3, 4) Setting the SOUTi initial value to “H” (Note 2) Port selection switching (I/O port SOUTi) Note 1: This diagram applies to the case where the SiC register bits are set as follows: SMi2=0 (SOUTi output), SMi5=0 (LSB first) and SMi6=0 (external clock) Note 2: SOUTi can only be initialized when input on the CLKi pin is in the high state if the SiC register’s SMi4 bit = 0 (transmit data output at the falling edge of the transfer clock) or in the low state if the SMi4 bit = 1 (transmit data output at the rising edge of the transfer clock). Note 3: If the SMi6 bit = 1 (internal clock) or if the SMi2 bit = 1 (SOUT output disabled), this output goes to the high-impedance state. Figure 1.17.5. SOUTi’s Initial Value Setting Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 136 of 201 Write to the SiTRR register Serial transmit/reception starts M16C/6S Group Programmable I/O Ports Programmable I/O Ports The programmable input/output ports (hereafter referred to simply as “I/O ports”) consist of 55 lines P1, P4 to P9 (except P85). Each port can be set for input or output every line by using a direction register, and can also be chosen to be or not be pulled high every 4 lines. P85 is an input-only port and does not have a pullup resistor. There is no external connections for port P1_0 to P1_4, P1_6 to P1_7, P4_0 to P4_7, P5_0 to P5_7, P7_2, P7_5, P7_7, P8_2, P8_6 to P8_7, P9_3 to P9_7. Figures 1.18.1 to 1.18.4 show the I/O ports. Figure 1.18.5 shows the I/O pins. Each pin functions as an I/O port, a peripheral function input/output. For details on how to set peripheral functions, refer to each functional description in this manual. If any pin is used as a peripheral function input, set the direction bit for that pin to “0” (input mode). Any pin used as an output pin for peripheral functions is directed for output no matter how the corresponding direction bit is set. (1) Port Pi Direction Register (PDi Register, i, 4 to 9) Figure 1.18.6 shows the direction registers. This register selects whether the I/O port is to be used for input or output. The bits in this register correspond one for one to each port. No direction register bit for P85 is available. (2) Port Pi Register (Pi Register, i = 1, 4 to 9) Figure 1.18.7 show the Pi registers. Data input/output to and from external devices are accomplished by reading and writing to the Pi register. The Pi register consists of a port latch to hold the input/output data and a circuit to read the pin status. For ports set for input mode, the input level of the pin can be read by reading the corresponding Pi register, and data can be written to the port latch by writing to the Pi register. For ports set for output mode, the port latch can be read by reading the corresponding Pi register, and data can be written to the port latch by writing to the Pi register. The data written to the port latch is output from the pin. The bits in the Pi register correspond one for one to each port. (3) Pull-up Control Register 0 to Pull-up Control Register 2 (PUR0 to PUR2 Registers) Figure 1.18.8 shows the PUR0 to PUR2 registers. The PUR0 to PUR2 register bits can be used to select whether or not to pull the corresponding port high in 4 bit units. The port chosen to be pulled high has a pull-up resistor connected to it when the direction bit is set for input mode. (4) Port Control Register Figure 1.18.9 shows the port control register. When the P1 register is read after setting the PCR register’s PCR0 bit to “1”, the corresponding port latch can be read no matter how the PD1 register is set. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 137 of 201 M16C/6S Group Programmable I/O Ports Direction register IT800 P40, P42, P56 Data bus Port latch Direction register P53, P54 Data bus Port latch IT800 Pull-up selection P15 Port P1 control register Data bus Port latch (Note 1) Input to respective peripheral functions Pull-up selection Direction register P60, P64, P73, P74, P76, P80, P81, P90, P92 "1" Output Data bus Port latch (Note 1) Input to respective peripheral functions Note 1: Figure 1.18.1. I/O Ports (1) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 138 of 201 symbolizes a parasitic diode. Make sure the input voltage on each port will not exceed Vcc. M16C/6S Group Programmable I/O Ports Pull-up selection Direction register P61, P65 "1" Output Data bus Port latch Switching between CMOS and Nch (Note 1) Input to respective peripheral functions Pull-up selection P83, P84 Direction register Port latch Data bus (Note 1) Input to respective peripheral functions Pull-up selection Direction register P91 Data bus Port latch (Note 1) Input to respective peripheral functions Note 1: Figure 1.18.2. I/O Ports (2) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 139 of 201 symbolizes a parasitic diode. Make sure the input voltage on each port will not exceed Vcc. M16C/6S Group Programmable I/O Ports Pull-up selection Direction register P62, P66, P71 Data bus Port latch (Note 1) Switching between CMOS and Nch Input to respective peripheral functions Pull-up selection Direction register P63, P67 “1” Data bus Port latch Output (Note 1) Switching between CMOS and Nch P85 Data bus (Note 1) Direction register P70 “1” Output Data bus Port latch (Note 2) Input to respective peripheral functions Note 1: symbolizes a parasitic diode. Make sure the input voltage on each port will not exceed Vcc. Note 2: symbolizes a parasitic diode. Figure 1.18.3. I/O Ports (3) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 140 of 201 M16C/6S Group Programmable I/O Ports Direction register “1” P95, P96 IT800 Output Data bus Port latch Direction register P82, P97, P41 Data bus Port latch Input to respective peripheral functions IT800 Direction register Testing signal P10, P11 Data bus Figure 1.18.4. I/O Ports (4) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 141 of 201 Port latch M16C/6S Group Programmable I/O Ports (Note 2) CNVSS CNVSS signal input (Note 1) RESET RESET signal input (Note 1) Note 1: symbolizes a parasitic diode. Make sure the input voltage on each port will not exceed Vcc. Note 2: A parasitic diode on the V CC side is added to the mask ROM version. Make sure the input voltage on each port will not exceed Vcc. Figure 1.18.5. I/O Pins Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 142 of 201 M16C/6S Group Programmable I/O Ports Port Pi direction register (i=1, 4 to 7 and 9) (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol PD1 PD4 to PD7 PD9 Bit symbol Address (Note 2) 03E316 03EA16, 03EB16, 03EE16, 03EF16 03F316 Bit name PDi_0 PDi_1 Port Pi0 direction bit Port Pi1 direction bit PDi_2 Port Pi2 direction bit PDi_3 Port Pi3 direction bit PDi_4 Port Pi4 direction bit PDi_5 Port Pi5 direction bit PDi_6 PDi_7 Port Pi6 direction bit Port Pi7 direction bit After reset 0016 0016 0016 Function 0 : Input mode (Functions as an input port) 1 : Output mode (Functions as an output port) (i = 0 to 7 and 9 to 13) RW RW RW RW RW RW RW RW RW Note 1: Make sure the PD9 register is written to by the next instruction after setting the PRCR register’s PRC2 bit to “1” (write enabled). Note 2: Set PD1_0 and PD1_1 bits to “0.” Port P8 direction register b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address 03F216 PD8 Bit symbol Bit name Function PD8_0 Port P80 direction bit PD8_1 Port P81 direction bit PD8_2 Port P82 direction bit PD8_3 Port P83 direction bit PD8_4 Port P84 direction bit Nothing is assigned. In an attempt to write to this bit, write “0”. The value, if read, turns out to be indeterminate. (b5) PD8_6 Port P86 direction bit PD8_7 Port P87 direction bit Figure 1.18.6. PD1, PD4 to PD9 Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 After reset 00X000002 page 143 of 201 0 : Input mode (Functions as an input port) 1 : Output mode (Functions as an output port) 0 : Input mode (Functions as an input port) 1 : Output mode (Functions as an output port) RW RW RW RW RW RW RW RW M16C/6S Group Programmable I/O Ports Port Pi register (i=1, 4 to 7 and 9) b7 b6 b5 b4 b3 b2 b1 Symbol P1 P4 to P7 P9 b0 Bit symbol Address (Note 2) 03E116 03E816, 03E916, 03EC16, 03ED16 03F116 Bit name Pi_0 Port Pi0 bit Pi_1 Pi_2 Port Pi1 bit Port Pi2 bit Pi_3 Port Pi3 bit Pi_4 Port Pi4 bit Pi_5 Port Pi5 bit Pi_6 Port Pi6 bit Pi_7 Port Pi7 bit After reset Indeterminate Indeterminate Indeterminate Function The pin level on any I/O port which is set for input mode can be read by reading the corresponding bit in this register. The pin level on any I/O port which is set for output mode can be controlled by writing to the corresponding bit in this register 0 : “L” level 1 : “H” level (Note 1) (i = 0 to 7 and 9 to 13) RW RW RW RW RW RW RW RW RW Note 1: Since P70 is N-channel open drain ports, the data is high-impedance. Note 2: Set P1_0 and P1_1 bits to “0.” Port P8 register b7 b6 b5 b4 b3 b2 b1 b0 Symbol P8 Bit symbol Bit name P8_0 Port P80 bit P8_1 Port P81 bit P8_2 Port P82 bit P8_3 Port P83 bit P8_4 Port P84 bit P8_5 Port P85 bit P8_6 Port P86 bit P8_7 Port P87 bit Figure 1.18.7. P1, P4 to P9 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 Address 03F016 page 144 of 201 After reset Indeterminate Function The pin level on any I/O port which is set for input mode can be read by reading the corresponding bit in this register. The pin level on any I/O port which is set for output mode can be controlled by writing to the corresponding bit in this register (except for P85) 0 : “L” level 1 : “H” level RW RW RW RW RW RW RO RW RW M16C/6S Group Programmable I/O Ports Pull-up control register 0 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol PUR0 Bit symbol (b2-b0) PU03 (b7-b4) Address 03FC16 After reset 0016 Bit name Function RW Nothing is assigned. When write, set to “0”. When read, its content is indeterminate. P14 to P17 pull-up 0 : Not pulled high 1 : Pulled high (Note 2) RW Nothing is assigned. When write, set to “0”. When read, its content is indeterminate. Note 1: During memory extension and microprocessor modes, the pins are not pulled high although their corresponding register contents can be modified. Note 2: The pin for which this bit is “1” (pulled high) and the direction bit is “0” (input mode) is pulled high. Pull-up control register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol PUR1 Bit symbol (b3-b0) Address 03FD16 After reset(Note 5) 000000002 000000102 Bit name Function RW Nothing is assigned. When write, set to “0”. When read, its content is indeterminate. PU14 P60 to P63 pull-up PU15 P64 to P67 pull-up PU16 P72 to P73 pull-up (Note 1) 0 : Not pulled high 1 : Pulled high (Note 3) RW RW RW RW PU17 P74 to P77 pull-up Note 1: The P70 and P71 pins do not have pull-ups. Note 2: During memory extension and microprocessor modes, the pins are not pulled high although the contents of these bits can be modified. Note 3: The pin for which this bit is “1” (pulled high) and the direction bit is “0” (input mode) is pulled high. Note 4: If the PM01 to PM00 bits are set to “012” (memory expansion mode) or “11 2” (microprocessor mode) in a program during single-chip mode, the PU11 bit becomes “1”. Note 5: The values after hardware reset 1 and 2 are as follows: • 000000002 when input on CNVss pin is “L“ • 000000102 when input on CNVss pin is “H“ The values after software reset, watchdog timer reset and oscillation stop detection reset are as follows: • 000000002 when PM 01 to PM00 bits of PM0 register are “002“ (single-chip mode) • 000000102 when PM 01 to PM00 bits of PM0 register are “012“ (memory expansion mode) or “11 2“ (microprocessor mode) Pull-up control register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol PUR2 Bit symbol Address 03FE16 Bit name PU20 P80 to P83 pull-up PU21 PU22 P84 to P87 pull-up (Note 2) P90 to P93 pull-up (b7-b3) After reset 0016 Function 0 : Not pulled high 1 : Pulled high (Note 1) Nothing is assigned. In an attempt to write to these bits, write “0”. The value, if read, turns out to be “0”. Note 1: The pin for which this bit is “1” (pulled high) and the direction bit is “0” (input mode) is pulled high. Note 2: The P85 pin does not have pull-up. Figure 1.18.8. PUR0 to PUR2 Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 145 of 201 RW RW RW RW M16C/6S Group Programmable I/O Ports Port control register b7 b6 b5 b4 b3 b2 b1 b0 Symbpl PCR Bit symbol PCR0 Address 03FF16 Bit name Port P1 control bit After reset 0016 Function Nothing is assigned. In an attempt to write to these bits, (b7-b1) Figure 1.18.9. PCR Register Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 146 of 201 RW Operation performed when the P1 register is read 0: When the port is set for input, the input levels of P10 to P17 RW pins are read. When set for output, the port latch is read. 1: The port latch is read regardless of whether the port is set for input or output. write “0”. The value, if read, turns out to be “0”. M16C/6S Group Programmable I/O Ports Table 1.18.1. Unassigned Pin Handling in Single-chip Mode (Excluding Analog Pins) Pin name Connection Ports P1, P6 to P9 (excluding P8 5) After setting for input mode, connect every pin to V SS via a resistor(pull-down); or after setting for output mode, leave these pins open. (2, 3, 4) XOUT (Note 1) Open P85 Connect via resistor to V CC (pull-up) VCCA Connect to V CC VSSA Connect to V SS NOTES: 1. With external clock input to XIN pin. 2. When setting the port for output mode and leave it open, be aware that the port remains in input mode until it is switched to output mode in a program after reset. For this reason, the voltage level on the pin becomes indeterminate, causing the power supply current to increase while the port remains in input mode. Furthermore, by considering a possibility that the contents of the direction registers could be changed by noise or noise-induced runaway, it is recommended that the contents of the direction registers be periodically reset in software, for the increased reliability of the program. 3. Make sure the unused pins are processed with the shortest possible wiring from the microcomputer pins (within 2 cm). 4. When the port P7_0 is set for output mode, make sure a low-level signal is output from the pin. The port P7_0 is N-channel open-drain output. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 147 of 201 M16C/6S Group Programmable I/O Ports Microcomputer Port P1, P6 to P9 (except for P85) (Note 2) (Input mode) · · · (Input mode) (Output mode) · · · Open P85 XOUT Open VCC VCCA VSSA VSS In single-chip mode Figure 1.18.10. Unassigned Pins Handling (Excluding Analog Pins) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 148 of 201 M16C/6S Group Electrical Characteristics Electrical Characteristics Table 1.19.1. Absolute Maximum Ratings Condition Rated value Unit VCC Symbol Supply voltage Parameter VCC=VCCA -0.3 to 4.2 V VCCA Analog supply voltage VCC=VCCA -0.3 to 4.2 V -0.3 to VCC+0.3 V -0.3 to 6.5 V -0.3 to VCC1+0.3 V Input voltage VI RESET, CNVSS P60 to P67, P71, P73, P74, P76, P80 to P85, P90 to P92, XIN P70 Output voltage VO P60 to P67, P71, P73, P74, P76, P80 to P84, P90 to P92, XOUT, TS P70 Pd Power dissipation Topr Operating ambient temperature Tstg Storage temperature Note 1: Refer to Tables 1.1.5 and 1.1.6 Product code. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 149 of 201 -0.3 to 6.5 V 500 mW -20 to 85/-40 to 85/-40 to 105 (Note 1) C -65 to 150 C M16C/6S Group Electrical Characteristics Table 1.19.2. Recommended Operating Conditions (Note 1) Parameter Symbol Min. Vcc A Analog supply voltage Vss Supply voltage 0 V V Analog supply voltage 0 V VIH 3.6 Unit Supply voltage HIGH input voltage 3.3 Max. VCC Vss A 3.0 Standard Typ. VCC P60 to P67, P71, P73, P74, P76, P80 to P84, P90 to P92 V 0.8VCC VCC V 0.8VCC 6.5 V 0 0.2VCC V P60 to P67, P71, P73, P74, P76, P80 to P84, P90 to P92, TS -10.0 mA P60 to P67, P71, P73, P74, P76, P80 to P84, P90 to P92, TS - 5 .0 mA P60 to P67, P70, P71, P73, P74, P76, P80 to P84, P90 to P92, TS 10.0 mA P60 to P67, P70, P71, P73, P74, P76, P80 to P84, P90 to P92, TS 5.0 mA XIN, RESET, CNVSS P70 LOW input voltage VIL P60 to P67, P70, P71, P73, P74, P76, P80 to P84, P90 to P92 XIN, RESET, CNVSS I OH (peak) HIGH peak output current I OH (avg) HIGH average output current I OL (peak) LOW peak output current I OL (avg) LOW average output current f (XIN) Main clock input oscillation frequency (Note 4) f (Ring) Ring oscillation frequency f (BCLK) CPU operation clock TSU(PLL) PLL frequency synthesizer stabilization wait time VCC=3.0 to 3.6V 5.12 MHz 1 MHz 15.36 VCC=3.0V MHz 50 Note 1: Referenced to VCC = 3.0 to 3.6V at Topr = -20 to 85 °C/-40 to 85 °C/-40 to 105 °C unless otherwise specified. Note 2: The mean output current is the mean value within 100ms. Note 3: The total IOL (peak) for all ports must be 80mA max, the total IOH (peak) for all ports must be -40mA max. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 150 of 201 ms M16C/6S Group Electrical Characteristics Table 1.19.3. Flash Memory Version Electrical Characteristics (Note 1) Parameter Symbol Standard Min. Typ. (Note 2) Max 100/1000 (Note 4, 6 ) – Erase/Write cycle (Note 3) – – Word program time (Vcc=3.3V, Topr=25°C) 75 Block erase time Unit cycle 600 µs 8Kbyte block 0.4 9 s 16Kbyte block 0.7 9 s 32Kbyte block 1.2 9 s 15 µs tPS Flash Memory Circuit Stabilization Wait Time – Data retention time (Note 5) 20 year Note 1: When not otherwise specified, Vcc = 3.0 to 3.6V; Topr = 0 to 60 °C. Note 2: VCC = 3.3V; Topr = 25 °C. Note 3: Program and Erase Endurance refers to the number of times a block erase can be performed. If the program and erase endurance is n (n=100, 1,000), each block can be erased n times. For example, if a 8Kbytes block 0 is erased after writing 1 word data 4096 times, each to a different address, this counts as one program and erase endurance. Data cannot be written to the same address more than once without erasing the block. (Rewrite prohibited) Note 4: Maximum number of E/W cycles for which opration is guaranteed. Note 5: Topr = 55°C. Note 6: The program area for U3 and U5 is 100 E/W cycles; the program area for U7 and U9 is 1,000 E/W cycles. Note 7: Customers desiring E/W failure rate information should contact their Renesas technical support representative. Table 1.19.4. Flash Memory Version Program/Erase Voltage and Read Operation Voltage Characteristics (at Topr = 0 to 60oC) Flash program, erase voltage Flash read operation voltage VCC = 3.3 V ± 0.3 V VCC = 3.0 to 3.6 V Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 151 of 201 M16C/6S Group Electrical Characteristics Table 1.19.5. Power Supply Circuit Timing Characteristics Symbol Parameter td(P-R) Time for internal power supply stabilization during powering-on td(R-S) STOP release time td(M-L) Time for internal power supply stabilization when main clock oscillation starts Measuring condition VCC =3.0 to 3.6V Interrupt for stop mode release CPU clock td(R-S) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 152 of 201 Min. Standard Typ. Max. Unit 2 ms 150 µs 50 µs M16C/6S Group Electrical Characteristics Table 1.19.6. Electrical Characteristics (Note) Symbol Parameter P60 to P67, P71, P73, P74, P76, P80 to P84, P90 to P92, TS V OH HIGH output voltage V OH HIGH output voltage V OL LOW output voltage V OL LOW output voltage P60 to P67, P71, P73, P74, P76, P80 to P84, P90 to P92, TS Hysteresis V T+-V T- V T+-V T- X OUT Unit V CC V I OH= -0.1mA VCC-0.5 V CC V I OL=1mA 0.5 V I OL=0.1mA 0.5 V 0.8 V 1.8 V V I =3V 4.0 µA V I =0V -4.0 µA 500 kΩ TA0IN, TA1IN, TA4IN, INT1 to INT3, RESET 0.2 HIGH input current P60 to P67, P70, P71, P73, P74, P76, P80 to P84, P90 to P92 X IN , RESET, CNVss (0.7) P60 to P67, P70, P71, P73, P74, P76, P80 to P84, P90 to P92 X IN , RESET, CNVss Pull-up resistance Max. VCC-0.5 Hysteresis LOW input current Typ. I OH= -1mA 0.2 I IL P60 to P67, P71, P73, P74, P76, P80 to P84, P90 to P92 V I =0V RfXIN Standard Min. CTS0 to CTS2, SCL, SDA, CLK 0 to CLK4, TA4OUT, RxD0 to RxD2, SIN3 I IH RPULLUP X OUT Measuring condition Feedback resistance 66 X IN Note : Referenced to VCC = 3.0 to 3.6V, VSS = 0V at Topr = -20 to 85 °C/-40 to 85 °C/-40 to 105 °C, f(BCLK) = 15.36 MHz unless otherwise specified. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 153 of 201 160 3.0 MΩ M16C/6S Group Electrical Characteristics Table 1.19.7. Electrical Characteristics (2) (Note 1) Symbol ICC Measuring condition Parameter Power supply current (VCC=2.7 to 3.6V) In single-chip mode, the output pins are open and other pins are VSS Min. Standard Typ. Max. 95 Flash memory f(BCLK)=15.36 MHz, No division 70 Flash memory Program f(BCLK)=10MHz, Vcc1=3.0V TBD mA Flash memory Erase f(BCLK)=10MHz, Vcc1=3.0V TBD mA Note : Referenced to VCC = 3.0 to 3.6V, VSS = 0V at Topr = -20 to 85 °C/-40 to 85 °C/-40 to 105 °C, f(BCLK) = 15.36 MHz unless otherwise specified. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 154 of 201 Unit mA M16C/6S Group Electrical Characteristics Timing Requirements (VCC = 3V, VSS = 0V, at Topr = – 20 to 85oC/– 40 to 85oC/– 40 to 105oC unless otherwise specified) Table 1.19.8. External Clock Input Symbol tc tw(H) tw(L) tr tf Parameter External clock input cycle time External clock input HIGH pulse width External clock input LOW pulse width External clock rise time External clock fall time Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 155 of 201 Standard Min. Max. Unit ns 195.3 80 80 18 18 ns ns ns ns M16C/6S Group Electrical Characteristics Timing Requirements (VCC = 3V, VSS = 0V, at Topr = – 20 to 85oC/– 40 to 85oC/– 40 to 105oC unless otherwise specified) Table 1.19.9. Timer A Input (Counter Input in Event Counter Mode) Symbol tc(TA) Parameter TAiIN input cycle time Standard Max. Min. 150 tw(TAH) TAiIN input HIGH pulse width 60 tw(TAL) TAiIN input LOW pulse width 60 Unit ns ns ns Table 1.19.10. Timer A Input (Gating Input in Timer Mode) Symbol Parameter tc(TA) TAiIN input cycle time tw(TAH) tw(TAL) TAiIN input HIGH pulse width TAiIN input LOW pulse width Standard Min. Max. 600 Unit ns 300 ns 300 ns Table 1.19.11. Timer A Input (External Trigger Input in One-shot Timer Mode) Symbol Parameter Standard Min. Max. Unit tc(TA) TAiIN input cycle time 300 ns tw(TAH) tw(TAL) TAiIN input HIGH pulse width TAiIN input LOW pulse width 150 ns 150 ns Table 1.19.12. Timer A Input (External Trigger Input in Pulse Width Modulation Mode) Symbol tw(TAH) tw(TAL) Parameter TAiIN input HIGH pulse width TAiIN input LOW pulse width Standard Min. Max. 150 150 Unit ns ns Table 1.19.13. Timer A Input (Counter Increment/decrement Input in Event Counter Mode) tc(UP) TAiOUT input cycle time Standard Max. Min. 3000 tw(UPH) TAiOUT input HIGH pulse width 1500 ns tw(UPL) TAiOUT input LOW pulse width ns tsu(UP-TIN) TAiOUT input setup time TAiOUT input hold time 1500 600 600 ns Symbol th(TIN-UP) Parameter Unit ns ns Table 1.19.14. Timer A Input (Two-phase Pulse Input in Event Counter Mode) Symbol Parameter Standard Max. Min. 2 Unit tc(TA) TAiIN input cycle time tsu(TAIN -TAOUT ) TAiOUT input setup time 500 µs ns tsu(TAOUT -TAIN) TAiIN input setup time 500 ns Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 156 of 201 M16C/6S Group Electrical Characteristics Timing Requirements (VCC = 3V, VSS = 0V, at Topr = – 20 to 85oC/– 40 to 85oC/– 40 to 105oC unless otherwise specified) Table 1.19.15. Serial I/O Symbol Parameter Standard Min. Max. Unit tc(CK) CLKi input cycle time 300 ns tw(CKH) CLKi input HIGH pulse width 150 ns 150 tw(CKL) CLKi input LOW pulse width td(C-Q) TxDi output delay time th(C-Q) TxDi hold time tsu(D-C) RxDi input setup time RxDi input hold time th(C-D) ns 160 ns 0 100 ns 90 ns ns _______ Table 1.19.16. External Interrupt INTi Input Symbol Parameter tw(INH) INTi input HIGH pulse width tw(INL) INTi input LOW pulse width Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 157 of 201 Standard Min. 380 380 Max. Unit ns ns M16C/6S Group Electrical Characteristics tc(TA) tw(TAH) TAi IN input tw(TAL) tc(UP) tw(UPH) TAi OUT input tw(UPL) TAi OUT input (Up/down input) During event counter mode TAi IN input (When count on falling edge is selected) th(TIN–UP) tsu(UP–TIN) TAi IN input (When count on rising edge is selected) Two-phase pulse input in event counter mode tc(TA) TAi IN input tsu(TA IN-TA OUT) tsu(TA IN-TA OUT) tsu(TA OUT-TA IN) TAi OUT input tsu(TA OUT-TA IN) Figure 1.19.1. Timing Diagram (1) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 158 of 201 M16C/6S Group Electrical Characteristics tc(CK) tw(CKH) CLKi tw(CKL) th(C–Q) TxDi td(C–Q) tsu(D–C) RxDi tw(INL) INTi input tw(INH) Figure 1.19.2. Timing Diagram (2) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 159 of 201 th(C–D) M16C/6S Group Flash Memory Version Flash Memory Version Flash Memory Performance The flash memory version has three modes—CPU rewrite, standard serial input/output, and parallel input/ output modes—in which its internal flash memory can be operated on. Note: About the parallel programmer of exclusive use, there is no schedule of development at the present time. Table 1.20.1 shows the outline performance of flash memory version (see Table 1.1.1 for the items not listed in Table 1.20.1.). Table 1.20.1. Flash Memory Version Specifications Item Specification Flash memory operating mode 2 modes (CPU rewrite, standard serial I/O) Erase block See Figure 1.20.1 Flash Memory Block Diagram Program method In units of word Erase method Block erase Program, erase control method Program and erase controlled by software command Protect method The block 0 and block 1 are write protected by bit FMR02. Number of commands 5 commands Program/Erase Endurance(Note) 100 times or 1,000 times (See Tables 1.1.5 and 1.1.6 Product code.) Block 0 to 4 (program area) Data Retention 20 years (Topr = 55°C) ROM code protection Standard serial I/O mode is supported. Note: Program and erase endurance definition Program and erase endurance are the erase endurance of each block. If the program and erase endurance are n times (n=100,1,000), each block can be erased n times. For example, if a 8-Kbyte block 0 is erased after writing 1 word data 4096 times, each to different addresses, this is counted as one program and erasure. However, data cannot be written to the same address more than once without erasing the block. (Rewrite disabled) Table 1.20.2. Flash Memory Rewrite Modes Overview Flash memory rewrite mode Function Areas which can be rewritten Operation mode ROM programmer CPU rewrite mode The user ROM area is rewritten by executing software commands from the CPU. EW0 mode: Can be rewritten in any area other than the flash memory EW1 mode: Can be rewritten in the flash memory User ROM area Standard serial I/O mode The user ROM area is rewritten by using a dedicated serial programmer. Standard serial I/O mode 1: Clock sync serial I/O Standard serial I/O mode 2: UART User ROM area Single chip mode Boot mode Memory expansion mode (EW0 mode) Boot mode (EW0 mode) None Serial programmer Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 160 of 201 M16C/6S Group Flash Memory Version 1. Memory Map The ROM in the flash memory version is separated between a user ROM area and a boot ROM area. Figures 1.20.1 and 1.20.2 show the block diagram of flash memory. The user ROM area is divided into several blocks, so that memory can be erased one block at a time. The user ROM area can be rewritten in all of CPU rewrite, standard serial input/output, and parallel input/output modes. The boot ROM area is reserved. The rewrite control program for standard serial I/O mode is stored in this area before shipment, so that the area cannot be rewritten. 0F000016 Block 3 : 32K bytes 0F7FFF16 0F800016 Block 2 : 16K bytes 0FBFFF16 0FC00016 Block 1 : 8K bytes 0FDFFF16 0FE00016 Block 0 : 8K bytes 0FFFFF16 User ROM area 0FF00016 0FFFFF16 4K bytes Boot ROM area (Reserved) Note 1: To specify a block, use an even address in that block. Note 2: Blocks 0 and 1 can be rewritten if FMR02 of FMR0 register is set to "1" (only in case of CPU rewriting mode.) Figure 1.20.1. Flash Memory Block Diagram (ROM Capacity 64K bytes) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 161 of 201 M16C/6S Group 0E800016 Block 4 : 32K bytes 0EFFFF16 0F000016 Block 3 : 32K bytes 0F7FFF16 0F800016 Block 2 : 16K bytes 0FBFFF16 0FC00016 Block 1 : 8K bytes 0FDFFF16 0FE00016 Block 0 : 8K bytes 0FFFFF16 User ROM area 0FF00016 0FFFFF16 4K bytes Boot ROM area (Reserved) Note 1: To specify a block, use an even address in that block. Note 2: Blocks 0 and 1 can be rewritten if FMR02 of FMR0 register is set to "1" (only in case of CPU rewriting mode.) Figure 1.20.2. Flash Memory Block Diagram (ROM Capacity 96K bytes) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 162 of 201 M16C/6S Group Flash Memory Version Boot Mode After a hardware reset which is performed by applying a high-level signal to the CNVSS and P15 pins, the microcomputer is placed in boot mode, thereby executing the program in the boot ROM area. The boot ROM area contains a standard serial input/output mode based rewrite control program which was stored in it when shipped from the factory. Functions To Prevent Flash Memory from Rewriting To prevent the flash memory from being read or rewritten easily, parallel input/output mode has a ROM code protect and standard serial input/output mode has an ID code check function. • ROM Code Protect Function The ROM code protect function inhibits the flash memory from being read or rewritten during parallel input/output mode. Figure 1.20.3 shows the ROMCP register. The ROMCP register is located in the user ROM area.The ROMCP1 bit consists of two bits. The ROM code protect function is enabled by clearing one or both of two ROMCP1 bits to “0” when the ROMCR bits are not ‘002,’ with the flash memory thereby protected against reading or rewriting. Conversely, when the ROMCR bits are ‘002’ (ROM code protect removed), the flash memory can be read or rewritten. Once the ROM code protect function is enabled, the ROMCR bits cannot be changed during parallel input/output mode. Therefore, use standard serial input/output or other modes to rewrite the flash memory. • ID Code Check Function Use this function in standard serial input/output mode. Unless the flash memory is blank, the ID codes sent from the programmer and the ID codes written in the flash memory are compared to see if they match. If the ID codes do not match, the commands sent from the programmer are not accepted. The ID code consists of 8-bit data, the areas of which, beginning with the first byte, are 0FFFDF16, 0FFFE316, 0FFFEB16, 0FFFEF16, 0FFFF316, 0FFFF716, and 0FFFFB16. Prepare a program in which the ID codes are preset at these addresses and write it in the flash memory. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 163 of 201 M16C/6S Group Flash Memory Version ROM code protect control address b7 b6 b5 b4 b3 b2 b1 b0 1 1 1 1 Symbol ROMCP Address 0FFFFF16 Bit name Bit symbol ROMCR ROMCP1 Value when shipped FF16 (Note 4) Function RW Reserved bit Set this bit to “1” RW Reserved bit Set this bit to “1” RW Reserved bit Set this bit to “1” RW Reserved bit Set this bit to “1” RW ROM code protect reset bit (Note 2, Note 4) b5 b4 ROM code protect level 1 set bit (Note 1, Note 3, Note 4) 00: Removes protect 01: 10: Enables ROOMCP1 bit 11: } RW RW b7 b6 00: Protect enabled 01: 10: 11: Protect disabled } RW RW Note 1: If the ROMCR bits are set to other than ‘002’ and the ROMCP1 bits are set to other than ‘112’ ( ROM code protect enabled), the flash memory is disabled against reading and rewriting in parallel input/output mode. Note 2: If the ROMCR bits are set to ‘002’ when the ROMCR bits are other than ‘002’ and the ROMCP1 bits are other than ‘112,’ ROM code protect level 1 is removed. However, because the ROMCR bits cannot be modified during parallel input/output mode, they need to be modified in standard serial input/output or other modes. Note 3: The ROMCP1 bits are effective when the ROMCR bits are ‘012,’ ‘102,’ or ‘112.’ Note 4: Once any of these bits is cleared to “0”, it cannot be set back to “1”. If a memory block that contains the ROMCP register is erased, the ROMCP register is set to ‘FF16.’ Figure 1.20.3. ROMCP Register Address 0FFFDF16 to 0FFFDC16 ID1 0FFFE316 to 0FFFE016 ID2 0FFFE716 to 0FFFE416 0FFFEB16 to 0FFFE816 Undefined instruction vector Overflow vector BRK instruction vector ID3 0FFFEF16 to 0FFFEC16 ID4 Address match vector Single step vector 0FFFF316 to 0FFFF016 ID5 Watchdog timer vector 0FFFF716 to 0FFFF416 ID6 DBC vector 0FFFFB16 to 0FFFF816 ID7 Reserved 0FFFFF16 to 0FFFFC16 ROMCP Reset vector 4 bytes Figure 1.20.4. Address for ID Code Stored Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 164 of 201 M16C/6S Group Flash Memory Version CPU Rewrite Mode In CPU rewrite mode, the user ROM area can be rewritten by executing software commands from the CPU. Therefore, the user ROM area can be rewritten directly while the microcomputer is mounted on-board without having to use a ROM programmer, etc. Make sure the Program and the Block Erase commands are executed only on each block in the user ROM area. During CPU rewrite mode, the user ROM area be operated on in either Erase Write 0 (EW0) mode or Erase Write 1 (EW1) mode. Table 1.21.1 lists the differences between Erase Write 0 (EW0) and Erase Write 1 (EW1) modes. Table 1.21.1. EW0 Mode and EW1 Mode Item Operation mode Areas in which a rewrite control program can be located Areas in which a rewrite control program can be executed Areas which can be rewritten Software command limitations Modes after Program or Erase CPU status during Auto Write and Auto Erase EW0 mode • Single chip mode • User ROM area EW1 mode Single chip mode User ROM area Must be transferred to any area other Can be executed directly in the user than the flash memory (e.g., RAM) ROM area before being executed User ROM area User ROM area However, this does not include the area in which a rewrite control program exists None • Program, Block Erase command Cannot be executed on any block in which a rewrite control program exists • Read Status Register command Cannot be executed Read Status Register mode Read Array mode Operating Flash memory status detection Hold state (I/O ports retain the state in which they were before the command was executed)(Note) Read the FMR0 register's FMR00, FMR06, and FMR07 bits in a program • Read the FMR0 register's FMR00, FMR06, and FMR07 bits in a program • Execute the Read Status Register command to read the status register's SR7, SR5, and SR4 flags. _______ Note: Make sure no interrupts (except NMI and watchdog timer interrupts) and DMA transfers will occur. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 165 of 201 M16C/6S Group Flash Memory Version • EW0 Mode The microcomputer is placed in CPU rewrite mode by setting the FMR0 register’s FMR01 bit to “1” (CPU rewrite mode enabled), ready to accept commands. In this case, because the FMR1 register’s FMR11 bit = 0, EW0 mode is selected. The FMR01 bit can be set to “1” by writing “0” and then “1” in succession. Use software commands to control program and erase operations. Read the FMR0 register or status register to check the status of program or erase operation at completion. • EW1 Mode EW1 mode is selected by setting FMR11 bit to “1” (by writing “0” and then “1” in succession) after setting the FMR01 bit to “1” (by writing “0” and then “1” in succession). Read the FMR0 register to check the status of program or erase operation at completion. The status register cannot be read during EW1 mode. When an erase/program operation is initiated the CPU halts all program execution until the operation is completed. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 166 of 201 M16C/6S Group Flash Memory Version Figure 1.21.1 shows the FMR0 and FMR1 registers. FMR00 Bit This bit indicates the operating status of the flash memory. The bit is “0” when the Program or Erase is running; otherwise, the bit is “1”. FMR01 Bit The microcomputer is made ready to accept commands by setting the FMR01 bit to “1” (CPU rewrite mode). FMR02 Bit When FMR02 bit is “0” (rewriting is disable), block 0 and block 1 do not receive the command of a program and block erase. FMSTP Bit This bit is provided for initializing the flash memory control circuits, as well as for reducing the amount of current consumed in the flash memory. The internal flash memory is disabled against access by setting the FMSTP bit to “1”. Therefore, the FMSTP bit must be written to by a program in other than the flash memory. In the following cases, set the FMSTP bit to “1”: • When flash memory access resulted in an error while erasing or programming in EW0 mode (FMR00 bit not reset to “1” (ready)) FMR06 Bit This is a read-only bit indicating the status of auto program operation. The bit is set to “1” when a program error occurs; otherwise, it is cleared to “0”. For details, refer to the description of the full status check. FMR07 Bit This is a read-only bit indicating the status of auto erase operation. The bit is set to “1” when an erase error occurs; otherwise, it is cleared to “0”. For details, refer to the description of the full status check. Figure 1.21.2 and 1.21.3 show the setting and resetting of EW0 mode and EW1 mode, respectively. FMR11 Bit Setting this bit to “1” places the microcomputer in EW1 mode. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 167 of 201 M16C/6S Group Flash Memory Version Flash memory control register 0 b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol Address After reset FMR0 01B716 XX0000012 0 Bit name Bit symbol Function RW FMR00 RY/BY status flag 0: Busy (being written or erased) 1: Ready FMR01 CPU rewrite mode select bit (Note 1) 0: Disables CPU rewrite mode 1: Inables CPU rewrite mode RW Lock bit disable select bit (Note 2) 0: Inables lock bit 1: Disables lock bit RW Flash memory stop bit (Note 3, Note 5)) 0: Enables flash memory operation 1: Stops flash memory operation (placed in low power mode, flash memory initialized) FMR02 FMSTP (b5-b4) Reserved bit RO RW Must always be set to “0” RW FMR06 Program status flag (Note 4) 0: Terminated normally 1: Terminated in error RO FMR07 Erase status flag (Note 4) 0: Terminated normally 1: Terminated in error RO Note 1: To set this bit to “1”, write “0” and then “1” in succession. Make sure no interrupts or DMA transfers will occur before writing “1” after writing “0”. Also, while in EW0 mode, write to this bit from a program in other than the flash memory. Note 2: To set this bit to “1”, write “0” and then “1” in succession when the FMR01 bit = 1. Make sure no interrupts or no DMA transfers will occur before writing “1” after writing “0”. Note 3: Write to this bit from a program in other than the flash memory. Note 4: This flag is cleared to “0” by executing the Clear Status command. Note 5: Effective when the FMR01 bit = 1 (CPU rewrite mode). If the FMR01 bit = 0, although the FMR03 bit can be set to “1” by writing “1” in a program, the flash memory is neither placed in low power mode nor initialized. Flash memory control register 1 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol Address After reset FMR1 01B516 0X00XX0X2 0 Bit name Bit symbol (b0) Reserved bit Function The value in this bit when read is indeterminate. 0: EW0 mode 1: EW1 mode RO FMR11 EW1 mode select bit ( Note) (b3-b2) Reserved bit The value in this bit when read is indeterminate. RO (b5-b4) Reserved bit Must always be set to “0” RW (b6) (b7) RW Nothing is assigned. When write, set to “0”. When read, their contents are indeterminate. Reserved bit Must always be set to “0” Note : To set this bit to “1”, write “0” and then “1” in succession when the FMR01 bit = 1. Make sure no interrupts or no DMA transfers will occur before writing “1” after writing “0”. The FMR01 and FMR11 bits both are cleared to “0” by setting the FMR01 bit to “0”. Figure 1.21.1. FIDR Register and FMR0 and FMR1 Registers Rev.5.01 Dec 10, 2009 REJ03B0014-0501 RW page 168 of 201 RW M16C/6S Group Flash Memory Version EW0 mode operation procedure Rewrite control program Single-chip mode Set CM0, CM1, and PM1 registers (Note1) Transfer a CPU rewrite mode based rewrite control program to any area other than the flash memory Jump to the rewrite control program which has been transferred to any area other than the flash memory (The subsequent processing is executed by the rewrite control program in any area other than the flash memory) Set the FMR01 bit by writing “0” and then “1” (CPU rewrite mode enabled) (Note 2) Execute software commands Execute the Read Array command Write “0” to the FMR01 bit (CPU rewrite mode disabled) Jump to a specified address in the flash memory Note 1: Select 10 MHz or less for CPU clock using the CM0 register’s CM06 bit and CM1 register’s CM17 to 6 bits. Also, set the PM1 register’s PM17 bit to “1” (with wait state). Note 2: To set the FMR01 bit to “1”, write “0” and then “1” in succession. Make sure no interrupts or no DMA transfers will occur before writing “1” after writing “0”. Write to the FMR01 bit from a program in other than the flash memory. Note 3: Disables the CPU rewrite mode after executing the Read Array command. Figure 1.21.2. Setting and Resetting of EW0 Mode Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 169 of 201 M16C/6S Group Flash Memory Version EW1 mode operation procedure Program in ROM Single-chip mode Set CM0, CM1, and PM1 registers (Note 1) Set the FMR01 bit by writing “0” and then “1” (CPU rewrite mode enabled) Set the FMR11 bit by writing “0” and then “1” (EW1 mode) (Note 2) Execute software commands Write “0” to the FMR01 bit (CPU rewrite mode disabled) Note 1: Select 10 MHz or less for CPU clock using the CM0 register’s CM06 bit and CM1 register’s CM17 to 6 bits. Also, set the PM1 register’s PM17 bit to “1” (with wait state). Note 2: To set the FMR01 bit to “1”, write “0” and then “1” in succession. Make sure no interrupts or no DMA transfers will occur before writing “1” after writing “0”. Write to the FMR01 bit from a program in other than the flash memory. Also write only when the NMI pin is “H” level. Figure 1.21.3. Setting and Resetting of EW1 Mode Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 170 of 201 M16C/6S Group Flash Memory Version Precautions on CPU Rewrite Mode Described below are the precautions to be observed when rewriting the flash memory in CPU rewrite mode. (1) Operation Speed Before entering CPU rewrite mode (EW0 or EW1 mode), select 10 MHz or less for BCLK using the CM06 bit in the CM0 register and the CM17 to CM16 bits in the CM1 register. Also, set the PM17 bit in the PM1 register to “1” (with wait state). (2) Instructions to Prevent from Using The following instructions cannot be used in EW0 mode because the flash memory’s internal data is referenced: UND instruction, INTO instruction, JMPS instruction, JSRS instruction, and BRK instruction (3) Interrupts EW0 Mode • Any interrupt which has a vector in the variable vector table can be used providing that its vector is transferred into the RAM area. _______ • The NMI and watchdog timer interrupts can be used because the FMR0 register and FMR1 register are initialized when one of those interrupts occurs. The jump addresses for those interrupt service routines should be set in the fixed vector table. _______ Because the rewrite operation is halted when a NMI or watchdog timer interrupt occurs, the rewrite program must be executed again after exiting the interrupt service routine. • The address match interrupt cannot be used because the flash memory’s internal data is referenced. EW1 Mode • Make sure that any interrupt which has a vector in the variable vector table or address match interrupt will not be accepted during the auto program or auto erase period. • Avoid using watchdog timer interrupts. • The WDT interrupt can be used because the FMR0 register and FMR1 register are initialized when this interrupt occurs. The jump address for the interrupt service routine should be set in the fixed vector table. Because the rewrite operation is halted when a WDT interrupt occurs, the rewrite program must be executed again after exiting the interrupt service routine. (4) How to Access To set the FMR01, FMR02, or FMR11 bit to “1”, write “0” and then “1” in succession. This is necessary to ensure that no interrupts or DMA transfers will occur before writing “1” after writing “0”. (5) Writing in the User ROM Space EW0 Mode • If the power supply voltage drops while rewriting any block in which the rewrite control program is stored, a problem may occur that the rewrite control program is not correctly rewritten and, consequently, the flash memory becomes unable to be rewritten thereafter. In this case, standard serial I/O or parallel I/O mode should be used. EW1 Mode • Avoid rewriting any block in which the rewrite control program is stored. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 171 of 201 M16C/6S Group Flash Memory Version (6) DMA Transfer In EW1 mode, make sure that no DMA transfers will occur while the FMR0 register’s FMR00 bit = 0 (during the auto program or auto erase period). (7) Writing Command and Data Write the command code and data at even addresses. (8) Wait Mode When shifting to wait mode, set the FMR01 bit to “0” (CPU rewrite mode disabled) before executing the WAIT instruction. (9) Stop Mode When shifting to stop mode, the following settings are required: • Set the FMR01 bit to “0” (CPU rewrite mode disabled) and disable DMA transfers before setting the CM10 bit to “1” (stop mode). • Execute the JMP.B instruction subsequent to the instruction which sets the CM10 bit to “1” (stop mode) Example program BSET 0, CM1 ; Stop mode JMP.B L1 L1: Program after returning from stop mode Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 172 of 201 M16C/6S Group Flash Memory Version Software Commands Software commands are described below. The command code and data must be read and written in 16bit units, to and from even addresses in the user ROM area. When writing command code, the 8 highorder bits (D1t–D8) are ignored. Table 1.21.2. Software Commands First bus cycle Command Mode Second bus cycle Address Data (D0 to D7) Mode Address Data (D0 to D7) Read X SRD Read array Write X xxFF16 Read status register Write X xx7016 Clear status register Write X xx5016 Program Write WA xx4016 Write WA WD Block erase Write X xx2016 Write BA xxD016 SRD: Status register data (D7 to D0) WA: Write address (Make sure the address value specified in the the first bus cycle is the same even address as the write address specified in the second bus cycle.) WD: Write data (16 bits) BA: Uppermost block address (even address, however) X: Any even address in the user ROM area x: High-order 8 bits of command code (ignored) Read Array Command (FF16) This command reads the flash memory. Writing ‘xxFF16’ in the first bus cycle places the microcomputer in read array mode. Enter the read address in the next or subsequent bus cycles, and the content of the specified address can be read in 16-bit units. Because the microcomputer remains in read array mode until another command is written, the contents of multiple addresses can be read in succession. However, when you use Read array command immediately after a program command, please read data in the following procedure. (1) FF16, FF16, FF16, and FF16 are written to 4 arbitrary continuous addresses. (2) The head address of (1) is specified in Read array mode. (3) (2) is repeated until the read value and FFFF16 are in agreement. (4) The head address +2 of (1) is specified. (5) (4) is repeated until the read value and FFFF16 are in agreement. (6) Arbitrary addresses are specified. Read Status Register Command (7016) This command reads the status register. Write ‘xx7016’ in the first bus cycle, and the status register can be read in the second bus cycle. (Refer to “Status Register.”) When reading the status register too, specify an even address in the user ROM area. Do not execute this command in EW1 mode. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 173 of 201 M16C/6S Group Flash Memory Version Clear Status Register Command (5016) This command clears the status register to “0”. Write ‘xx5016’ in the first bus cycle, and the FMR06 to FMR07 bits in the FMR0 register and SR4 to SR5 in the status register will be cleared to “0”. Program Command (4016) This command writes data to the flash memory in 1 word (2 byte) units. Write ‘xx4016’ in the first bus cycle and write data to the write address in the second bus cycle, and an auto program operation (data program and verify) will start. Make sure the address value specified in the first bus cycle is the same even address as the write address specified in the second bus cycle. Check the FMR00 bit in the FMR0 register to see if auto programming has finished. The FMR00 bit is “0” during auto programming and set to “1” when auto programming is completed. Check the FMR06 bit in the FMR0 register after auto programming has finished, and the result of auto programming can be known. (Refer to “Full Status Check.”) Writing over already programmed addresses is inhibited. Moreover, when FMR02 bit of FMR0 register is “0” (rewriting is disable), the program command to block 0 and block 1 is not received. Just behind a program command, when you execute commands other than a program command, please make it the address value which was specified by the 2nd bus cycle of a program command and which writes in and specifies the same address as an address by the 1st bus cycle of the following command. In EW1 mode, do not execute this command on any address at which the rewrite control program is located. In EW0 mode, the microcomputer goes to read status register mode at the same time auto programming starts, making it possible to read the status register. The status register bit 7 (SR7) is cleared to “0” at the same time auto programming starts, and set back to “1” when auto programming finishes. In this case, the microcomputer remains in read status register mode until a read command is written next. The result of auto programming can be known by reading the status register after auto programming has finished. Start Write the command code ‘xx4016’ to the write address Write data to the write address FMR00=1? NO YES Full status check Program completed Note: Write the command code and data at even number. Figure 1.21.4. Program Command Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 174 of 201 M16C/6S Group Flash Memory Version Block Erase Write ‘xx2016’ in the first bus cycle and write ‘xxD016’ to the uppermost address of a block (even address, however) in the second bus cycle, and an auto erase operation (erase and verify) will start. Check the FMR0 register’s FMR00 bit to see if auto erasing has finished. The FMR00 bit is “0” during auto erasing and set to “1” when auto erasing is completed. Check the FMR0 register’s FMR07 bit after auto erasing has finished, and the result of auto erasing can be known. (Refer to “Full Status Check.”) Moreover, when FMR02 bit of FMR0 register is “0” (rewriting is disable), the block erase command to block 0 and block 1 is not received. Figure 1.21.5 shows an example of a block erase flowchart. Each block can be protected against erasing by a lock bit. (Refer to “Data Protect Function.”) Writing over already programmed addresses is inhibited. In EW1 mode, do not execute this command on any address at which the rewrite control program is located. In EW0 mode, the microcomputer goes to read status register mode at the same time auto erasing starts, making it possible to read the status register. The status register bit 7 (SR7) is cleared to “0” at the same time auto erasing starts, and set back to “1” when auto erasing finishes. In this case, the microcomputer remains in read status register mode until the Read Array or Read Lock Bit Status command is written next. Start Write the command code ‘xx2016’ Write ‘xxD016’ to the uppermost block address FMR00=1? NO YES Full status check Block erase completed Note: Write the command code and data at even number. Figure 1.21.5. Block Erase Command Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 175 of 201 M16C/6S Group Flash Memory Version Status Register The status register indicates the operating status of the flash memory and whether an erase or programming operation terminated normally or in error. The status of the status register can be known by reading the FMR0 register’s FMR00, FMR06, and FMR07 bits. Table 1.21.3 shows the status register. In EW0 mode, the status register can be read in the following cases: (1) When a given even address in the user ROM area is read after writing the Read Status Register command (2) When a given even address in the user ROM area is read after executing the Program, Block Erase, Erase All Unlocked Block, or Lock Bit Program command but before executing the Read Array command. Sequencer Status (SR7 and FMR00 Bits ) The sequence status indicates the operating status of the flash memory. SR7 = 0 (busy) during auto programming and auto erase is set to “1” (ready) at the same time the operation finishes. Erase Status (SR5 and FMR07 Bits) Refer to “Full Status Check.” Program Status (SR4 and FMR06 Bits) Refer to “Full Status Check.” Table 1.21.3. Status Register • D0 to D7: Indicates the data bus which is read out when the Read Status Register command is executed. Value FMR0 Status Contents Status name after register register "0" "1" reset bit bit SR7 (D7) FMR00 Sequencer status Reserved SR6 (D6) Busy Ready - - 1 SR5 (D5) FMR07 Erase status Terminated normally Terminated in error 0 SR4 (D4) FMR06 Program status Terminated normally Terminated in error 0 SR3 (D3) Reserved - - SR2 (D2) Reserved - - SR1 (D1) Reserved - - SR0 (D0) Reserved - - • The FMR07 bit (SR5) and FMR06 bit (SR4) are cleared to “0” by executing the Clear Status Register command. • When the FMR07 bit (SR5) or FMR06 bit (SR4) = 1, the Program and Block Erase are not accepted. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 176 of 201 M16C/6S Group Flash Memory Version Full Status Check When an error occurs, the FMR0 register’s FMR06 to FMR07 bits are set to “1”, indicating occurrence of each specific error. Therefore, execution results can be verified by checking these status bits (full status check). Table 1.21.4 lists errors and FMR0 register status. Figure 1.21.6 shows a full status check flowchart and the action to be taken when each error occurs. Table 1.21.4. Errors and FMR0 Register Status FMR00 register (SRD register) status FMR07 FMR06 (SR5) (SR4) 1 1 Error Error occurrence condition Command • When any commands are not written correctly sequence error • A value other than ‘xxD016’ or ‘xxFF16’ is written in the second bus cycle of the block erase command (Note 1) • When the block erase command is executed on protected blocks • When the program command is executed on protected blocks 1 0 Erase error • When the block erase command is executed on unprotected blocks but the blocks are not automatically erased correctly 0 1 Program error • When the program command is executed on unprotected blocks but the blocks are not automatically programmed correctly. Note 1: The flash memory enters read array mode by writing command code ‘xxFF16’ in the second bus cycle of these commands. The command code written in the first bus cycle becomes invalid. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 177 of 201 M16C/6S Group Flash Memory Version Full status check FMR06 =1 and FMR07=1? YES Command sequence error (1) Execute the Clear Status Register command to clear these status flags to “0”. (2) Reexecute the command after checking that it is entered correctly. NO FMR07= 0? NO Erase error Note 1: If the error still occurs, the block in error cannot be used. YES FMR06= 0? (1) Execute the Clear Status Register command to clear the erase status flag to “0”. (2) Reexecute the Block Erase command. NO Program error YES [During programming] (1) Execute the Clear Status Register command to clear the erase status flag to “0”. (2) Reexecute the Program command. Note 2: If the error still occurs, the block in error cannot be used. Full status check completed Note 3: If FMR06 or FMR07 = 1, neither the Program nor Block Erase command is accepted. Execute the Clear Status Register command before executing those commands. Figure 1.21.6. Full Status Check and Handling Procedure for Each Error Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 178 of 201 M16C/6S Group Flash Memory Version Standard Serial I/O Mode The standard serial I/O mode inputs and outputs the software commands, addresses and data needed to operate (read, program, erase, etc.) the internal flash memory using the serial I/O port UART1. The serial I/O mode transfers the data serially in 8-bit units. In the standard serial I/O mode the CPU executes a control program for flash memory rewrite (using the CPU's rewrite mode), rewrite data input and so forth. It is started when both the P15 (CE) pin and the CNVss pin are in “H” level after the reset is released. (In normal operation mode, set CNVss pin to “L” level.) The main clock f1 is 5.12 MHz in this mode. This control program is written in the boot ROM area when the product is shipped. There are actually two standard serial I/O modes: mode 1, which is clock synchronized, and mode 2, which is asynchronized. Standard serial I/O switches between mode 1 (clock synchronous) and mode 2 (clock asynchronous) depending on the level of CLK1 pin when the reset is released. To use standard serial I/O mode 1 (clock synchronous), set the CLK1 pin to “H” level and release the reset. The operation uses the four UART1 pins CLK1, RxD1, TxD1 and RTS1 (BUSY). The CLK1 pin is the transfer clock input pin through which an external transfer clock is input. The TxD1 pin is for CMOS output. The RTS1 (BUSY) pin outputs an “L” level when ready for reception and an “H” level when reception starts. In mode 1, be sure the TxD1 (P67) pin is at high before reset being deasserted. To use standard serial I/O mode 2 (clock asynchronous), set the CLK1 pin to “L” level and release the reset. The operation uses the two UART1 pins RxD1 and TxD1. In standard serial input/output mode, the user ROM area can be rewritten while the microcomputer is mounted on-board by using a serial programmer suitable for the M16C/62P group. For more information about serial programmers, contact the manufacturer of your serial programmer. For details on how to use, refer to the user’s manual included with your serial programmer. Table 1.22.1 lists pin functions (flash memory standard serial input/output mode). Figures 1.22.1 to 1.22.2 show pin connections for serial input/output mode. ID Code Check Function This function determines whether the ID codes sent from the serial programmer and those written in the flash memory match. (Refer to the description of the functions to inhibit rewriting flash memory version.) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 179 of 201 M16C/6S Group Flash Memory Version Table 1.22.1. Functional explanation of pin (flash memory standard serial I/O mode) Pin Signal name Description I/O Apply the voltage guaranteed for Program and Erase to Vcc pin. Apply 0 V to Vss pin. VCC,VSS Power supply input CNVSS CNVSS I Connect to Vcc pin. RESET Reset input I Reset input pin. While RESET pin is "L" level, input a 20 cycle or longer clock to XIN pin. XIN Clock input I XOUT Clock output O Connect a ceramic resonator or crystal oscillator between XIN and XOUT pins. To input an externally generated clock, input it to XIN pin and open XOUT pin. VDCCN Input "H" level signal. VCCA, VSSA Analog power supply input I Please connect AVcc to Vcc and connect AVss to Vss. VREF Standard voltage input I Input the standard voltage of a preamplifier and an operational amplifier. P60 to P63 Input port P6 I Input "H" or "L" level signal or open. P64/RTS1 BUSY output O Standard serial I/O mode 1: BUSY signal output pin Standard serial I/O mode 2: Monitors the boot program operation check signal output pin. P65/CLK1 SCLK input I Standard serial I/O mode 1: Serial clock input pin Standard serial I/O mode 2: Input "L." P66/RXD1 RxD input I Serial data input pin. P67/TXD1 TxD output O Serial data output pin. (Note 1) P70, P71, P73, P74, P76 Input port P7 I Input "H" or "L" level signal or open. P80, P81, P83, P84, P85 Input port P8 I Input "H" or "L" level signal or open. P15 CE input I Input "H" level signal. P90 to P92 Input port P11 I Input "H" or "L" level signal or open. Note 1: When using standard serial input/output mode 1, the TxD pin must be held high while the RESET pin is pulled low. Therefore, connect this pin to Vcc1 via a resistor. Because this pin is directed for data output after reset, adjust the pull-up resistance value in the system so that data transfers will not be affected. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 180 of 201 M16C/6S Group Flash Memory Version Example of Circuit Application in the Standard Serial I/O Mode Figure 1.22.1 and 1.22.2 show example of circuit application in standard serial I/O mode 1 and mode 2, respectively. Refer to the user's manual for serial programmer to handle pins controlled by a serial programmer. Microcomputer SCLK Clock input P15(CE) TXD Data input BUSY BUSY output RxD Data output Reset input CNVss RESET User reset signal (1) Control pins and external circuitry will vary according to programmer. For more information, see the programmer manual. (2) In this example, modes are switched between single-chip mode and standard serial input/output mode by controlling the CNVss input with a switch. (3) If in standard serial input/output mode 1 there is a possibility that the user reset signal will go low during serial input/output mode, break the connection between the user reset signal and RESET pin by using, for example, a jumper switch. Figure 1.22.1. Circuit Application in Standard Serial I/O Mode 1 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 181 of 201 M16C/6S Group Flash Memory Version Microcomputer SCLK Data output TxD Monitor output BUSY Data input RxD P15(CE) CNVss (1) In this example, modes are switched between single-chip mode and standard serial input/output mode by controlling the CNVss input with a switch. Figure 1.22.2. Circuit Application in Standard Serial I/o Mode 2 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 182 of 201 M16C/6S Group Flash Memory Version ROM Code Protect Function The ROM code protect function inhibits the flash memory from being read or rewritten. (Refer to the description of the functions to inhibit rewriting flash memory version.) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 183 of 201 M16C/6S Group IT800AFE (Analog Front End) IT800AFE (Analog Front End) 1. The block diagram of analog front end Analog front end (AFE) part is the circuit located between M16C/6S and a power line, and M16C/6S build in DAC, preamplifier, and ADC. There are the following two signal circuits in AFE. (1)Transmitting circuit:It drives with the signal from the logic of M16C/6S inside, and this is consists of DAC with a differential output, Output filter for spectrum adjustment, Differential line driver amplifier and line coupling circuit which drive power line. (2)Receiving circuit:This is consists of Line coupling circuit, Differential preamplifier, Input filter group and ADC. Line coupling circuit is common to both transmission and reception. M16C/6S Line Driver Power line Output Filter DAC Line Driver Channel Filters ADC Pre Amp Input Filter Figure 1.23.1 Analog Front End circuit block diagram (1)Transmitting path The characteristics required for transmitting path are as follows. (a)A suitable output signal level is obtained on specific load. (b)Frequency characteristic is flat in signal bandwidth. (c)The signal level outside a zone: It is less than each regulation. This system assumes operation in the following three fundamental signal zones. (a)The U.S., Japan: 120k to 400kHz (b)Europe in door: 95k to 125kHz(CENELEC B Band) (c)Europe out door: 20k to 80kHz(CENELEC A Band) It is necessary to perform the change of a signal zone by change of adjustment of change of the configuration of IT800, the analog filter to a signal zone, or output electric power, and the output impedance of the line driver stage (notes). Note. Please refer to the following standard and style about the conditions outside a signal level or a zone. (a)The U.S.:FCC standard, part 15 (b)Europe:CENELEC standard, EN 50065-1 (c)Japan:ARIB STD-T84 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 184 of 201 M16C/6S Group IT800AFE (Analog Front End) About DAC (Digital to Analog Converter) DAC of built-in in M16C/6S is current output type 10 bit DAC.The standard level of output current can be set up by the external resistance linked to a built-in standard power supply. A DAC circuit and a load circuit are shown in Figure 1.23.2. The typical characteristic is shown in Table 1.23.1. 10 bit DAC Iout DATA D9-D0 Vref 10 7 Matrix Current Cell Rout 2.1k(1%) Cout 33pF Line Driver Amp + - 6 Ioutc Routc 2.1k(1%) Rext External pin (pin number) Coutc 33pF 8 Rext 2.1k(1%) LSI internal connection IFULL(mA)=2131/Rext(‰) =Iout+Ioutc At Rext=2.1k‰, IFULL=1mA Figure 1.23.2 DAC (Digital to Analog Converter) Table 1.23.1 DAC Electrical Characteristics (Vdd=3.3±0.3V, Ta = -20 to 85°C/-40 to 85°C/-40 to 105°C unless otherwise specified) Electrical Characteristics Symbol Parameter Condition Min Typ Max Unit Standard voltage Vref Rext=2.1kΩ 0.3 V Standard current Iref Rext=2.1kΩ 0.14 mA External standard register DAC output register Full-scale current Maximum output voltage Rev.5.01 Dec 10, 2009 REJ03B0014-0501 2.1 Rext Rout/Routc IFULL Rext=2.1kΩ Voutmax Rout/Routc=2.1kΩ page 185 of 201 kΩ 2.0 Rext=2.1kΩ 0.9 1 1.1 Vdd-1 kΩ mA V M16C/6S Group IT800AFE (Analog Front End) In the circumference of a DAC circuit, it is cautious of the following point and a constant is set up. (a)Full-scale output current of DAC Although the current by which DAC is outputted to a pin (Iout/Ioutc) according to the change width of an internal bit changes, total is fixed and serves as full-scale output current (IFULL). This IFULL can be set up by the following formula. IFULL=2131/Rext(mA) The unit of Rext is Ω Since about 1mA of an IFULL value is the optimal value, Rext is 2.1kΩ. DAC is total and Iout/Ioutc changes between 0 to IFULL at 1024 steps by the full range for a change width of 10 bits. The value of Iout/Ioutc is expressed with the following formula if the step value which converted the 10bit binary input into decimal is set to d. (d=0 to 1023) Iout=IFULL/1023*d Ioutc=IFULL/1023*(1023-d) (b)About DAC load resistance Resistance (Rout/Routc) is connected to a DAC output pin.In this resistance, signal voltage occurs by the current (Iout/Ioutc) which flows, respectively. In order to maintain the linearity of Iout/Ioutc, it is necessary to set up Rout/Routc so that this potential may not exceed maximum 2V. Since Iout/Ioutc is mostly set to one half of IFULL(s) at the time of a non-signal (balanced state), the signal voltage (Vout/Voutc) of a DAC output pin is set to below: Vout=Rout X Iout Voutc=Routc X Ioutc Since the recommendation value of Vout/Voutc at the time of a non-signal is about 1V, in Rext=2.1kΩ, Rout/Routc serves as 2.1kΩ. The capacitor (Cout/Coutc) for output filters cuts the high frequency ingredient of DAC, and sets it up on balance with necessary zone frequency. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 186 of 201 M16C/6S Group IT800AFE (Analog Front End) (2)Receiving circuit (a)Preamplifier A preamplifier circuit consists of two CMOS operational amplifiers as shown in Figure 1.23.3, the first opamp is connected as gain stage with gain of 20dB and the second opamp is connected as a voltage follower for driving of external filter. 3.3V 10k Vref 0.1µF 10k M16C/6S Pre-InP Input filter Amplifier Pre_BOut Buffer Pre-InN Figure 1.23.3 Consists of Preamp circuit Table 1.23.2 Preamp Electrical Characteristics (Ta = 25°C unless otherwise specified) Electrical Characteristics Parameter Symbol Standard voltage Condition Vdd Unit Min Typ Max 3.0 3.3 3.6 V 15 mV Input off-set voltage Vof Open loop gain GVO No-load 70 dB Gain band width BW GVO=0dB 5 MHz Common mode input range CMIR DC to 1MHz 0.7 Common mode rejection ratio Power supply rejection ratio CMRR PSRR DC to 1MHz 40 30 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 187 of 201 DC to 1MHz Vdd-0.7 V dB dB M16C/6S Group IT800AFE (Analog Front End) (b)ADC (Analog to Digital Converter) The output of the channel filter (maximum of three) connected outside is connected to 1 bit ADC which consists of an operational amplifier and a comparator. M16C/6S build in ADC of three equivalent performances. The circuit of one ADC has composition shown in the following figure. R1/R2/R3 C1/C2/C3 AMP1_Out/AMP2_Out/ AMP3_Out Channel Filter CH1_InP/CH2_InP/ CH3_InP 0.22µF 1k AMP1_IN/ AMP2_IN/ AMP3_IN/ Vref 3.3V + Amplifier Comparator + - 10k 0.1µF 10k CH1_InN/CH2_InN/ CH3_InN FB1/FB2/FB3 0.1µF Figure 1.23.4 ADC block diagram Three ADC use all three by the signal zone to be used. The constant of a filter is set up as shown in the following table. Table 1.23.3 The example of an ADC part constant setting Parts Capacitor Parts Register Application characteristic C1 C2 C3 Unit FCC/ARIB 33 22 10 pF CECLEC-B 33 Application characteristic R1 R2 R3 Unit FCC/ARIB 10 10 12 kΩ CECLEC-B 10 Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 188 of 201 pF kΩ M16C/6S Group Usage Notes Usage Notes Register Setting Immediate values should be set in the registers containing write-only bits. When establishing a new value by modifying a previous value, write the previous value into RAM as well as the register. Change the contents of the RAM and then transfer the new value to the register. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 189 of 201 M16C/6S Group Usage Notes Power Control When entering wait mode, insert a JMP.B instruction before a WAIT instruction. Do not excute any instructions which can generate a write to RAM between the JMP.B and WAIT instructions. Disable the DMA transfers, if a DMA transfer may occur between the JMP.B and WAIT instructions. After the WAIT instruction, insert at least 4 NOP instructions. When entering wait mode, the instruction queue reads ahead the instructions following WAIT, and depending on timing, some of these may execute before the MCU enters wait mode. Program example when entering wait mode Program Example: JMP.B L1: FSET WAIT NOP NOP NOP NOP L1 ; Insert JMP.B instruction before WAIT instruction I ; ; Enter wait mode ; More than 4 NOP instructions When entering stop mode, insert a JMP.B instruction immediately after executing an instruction which sets the CM10 bit in the CM1 register to 1, and then insert at least 4 NOP instructions. When entering stop mode, the instruction queue reads ahead the instructions following the instruction which sets the CM10 bit to 1 (all clock stops), and, some of these may execute before the MCU enters stop mode or before the interrupt routine for returning from stop mode. Program example when entering stop mode Program Example: FSET BSET JMP.B I CM10 L2 ; Enter stop mode ; Insert JMP.B instruction L2: NOP NOP NOP NOP ; More than 4 NOP instructions Stop mode and wait mode is cancelled by a hardware reset or an interrupt. if an interrupt is to be used to cancel stop mode and wait mode that interrupt must first have been enabled, and the priority level of the interrupt which is not used to cancel must have been changed to 0. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 190 of 201 M16C/6S Group Usage Notes Changing the Interrupt Generate Factor If the interrupt generate factor is changed, the IR bit in the interrupt control register for the changed interrupt may inadvertently be set to 1 (interrupt requested). If you changed the interrupt generate factor for an interrupt that needs to be used, be sure to clear the IR bit for that interrupt to 0 (interrupt not requested). “Changing the interrupt generate factor” referred to here means any act of changing the source, polarity or timing of the interrupt assigned to each software interrupt number. Therefore, if a mode change of any peripheral function involves changing the generate factor, polarity or timing of an interrupt, be sure to clear the IR bit for that interrupt to 0 (interrupt not requested) after making such changes. Refer to the description of each peripheral function for details about the interrupts from peripheral functions. Figure 1.24.1 shows the procedure for changing the interrupt generate factor. Changing the interrupt source Disable interrupts (2,3) Change the interrupt generate factor (including a mode change of peripheral function) Use the MOV instruction to clear the IR bit to 0 (interrupt not requested) (3) Enable interrupts (2,3) End of change IR bit: A bit in the interrupt control register for the interrupt whose interrupt generate factor is to be changed. NOTES: 1. The above settings must be executed individually. Do not execute two or more settings simultaneously (using one instruction). 2. Use the I flag for the INTi interrupt (i = 0 to 5). For the interrupts from peripheral functions other than the INTi interrupt, turn off the peripheral function that is the source of the interrupt in order not to generate an interrupt request before changing the interrupt generate factor. In this case, if the maskable interrupts can all be disabled without causing a problem, use the I flag. Otherwise, use the corresponding bits ILVL2 to ILVL0 for the interrupt whose interrupt generate factor is to be changed. 3. Refer to Rewrite the Interrupt Control Register for details about the instructions to use and the notes to be taken for instruction execution. Figure 1.24.1 Procedure for Changing the Interrupt Generate Factor Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 191 of 201 M16C/6S Group Usage Notes Watchdog Timer Interrupt Initialize the watchdog timer after the watchdog timer interrupt occurs. DMAC Write to DMAE Bit in DMiCON Register (i = 0 to 1) When both of the conditions below are met, follow the steps below. (a) Conditions • The DMAE bit is set to 1 again while it remains set (DMAi is in an active state). • A DMA request may occur simultaneously when the DMAE bit is being written. (b) Procedure (1) Write 1 to the DMAE bit and DMAS bit in DMiCON register simultaneously (1). (2) Make sure that the DMAi is in an initial state (2) in a program. If the DMAi is not in an initial state, the above steps should be repeated. NOTES: 1. The DMAS bit remains unchanged even if 1 is written. However, if 0 is written to this bit, it is set to 0 (DMA not requested). In order to prevent the DMAS bit from being modified to 0, 1 should be written to the DMAS bit when 1 is written to the DMAE bit. In this way the state of the DMAS bit immediately before being written can be maintained. Similarly, when writing to the DMAE bit with a read-modify-write instruction, 1 should be written to the DMAS bit in order to maintain a DMA request which is generated during execution. 2. Read the TCRi register to verify whether the DMAi is in an initial state. If the read value is equal to a value which was written to the TCRi register before DMA transfer start, the DMAi is in an initial state. (If a DMA request occurs after writing to the DMAE bit, the value written to the TCRi register is 1.) If the read value is a value in the middle of transfer, the DMAi is not in an initial state. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 192 of 201 M16C/6S Group Usage Notes Timers Timer A Timer A (Timer Mode) The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) register and the TAi register before setting the TAiS bit in the TABSR register to 1 (count starts). Always make sure the TAiMR register is modified while the TAiS bit remains 0 (count stops) regardless whether after reset or not. While counting is in progress, the counter value can be read out at any time by reading the TAi register. However, if the TAi register is read at the same time the counter is reloaded, the read value is always FFFF16. If the TAi register is read after setting a value in it, but before the counter starts counting, the read value is the one that has been set in the register. Timer A (Event Counter Mode) The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) register, the TAi register, the UDF register, bits TAZIE, TA0TGL, and TA0TGH in the ONSF register and the TRGSR register before setting the TAiS bit in the TABSR register to 1 (count starts). Always make sure bits TAZIE, TA0TGL, and TA0TGH in the TAiMR register, the UDF register, the ONSF register, and the TRGSR register are modified while the TAiS bit remains 0 (count stops) regardless whether after reset or not. While counting is in progress, the counter value can be read out at any time by reading the TAi register. However, if the TAi register is read at the same time the counter is reloaded, the read value is always FFFF16 when the timer counter underflows and 000016 when the timer counter overflows. If the TAi register is read after setting a value in it, but before the counter starts counting, the read value is the one that has been set in the register. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 193 of 201 M16C/6S Group Usage Notes Timer A (One-shot Timer Mode) The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) register, the TAi register, bits TA0TGL and TA0TGH in the ONSF register and the TRGSR register before setting the TAiS bit in the TABSR register to 1 (count starts). Always make sure bits TA0TGL and TA0TGH in the TAiMR register, the ONSF register, and the TRGSR register are modified while the TAiS bit remains 0 (count stops) regardless whether after reset or not. When setting TAiS bit to 0 (count stop), the followings occur: • A counter stops counting and a content of reload register is reloaded. • TAiOUT pin outputs “L”. • After one cycle of the CPU clock, the IR bit in TAiIC register is set to 1 (interrupt request). Output in one-shot timer mode synchronizes with a count source internally generated. When the external trigger has been selected, a maximun delay of one cycle of the count source occurs between the trigger input to TAiIN pin and output in one-shot timer mode. The IR bit is set to 1 when timer operation mode is set with any of the following procedures: • Select one-shot timer mode after reset. • Change an operation mode from timer mode to one-shot timer mode. • Change an operation mode from event counter mode to one-shot timer mode. To use the timer Ai interrupt (the IR bit), set the IR bit to 0 after the changes listed above have been made. When a trigger occurs while the timer is counting, the counter reloads the reload register value, and continues counting after a second trigger is generated and the counter is decremented once. To generate a trigger while counting, space more than one cycle of the timer count source from the first trigger and generate again. When selecting the external trigger for the count start conditions in timer A one-shot timer mode, do generate an external trigger 300ns before the count value of timer A is set to 000016. The one-shot timer does not continue counting and may stop. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 194 of 201 M16C/6S Group Usage Notes Timer A (Pulse Width Modulation Mode) The timer remains idle after reset. Set the mode, count source, counter value, etc. using bits TA0TGL and TA0TGH in the TAiMR (i = 0 to 4) register, the TAi register, the ONSF register and the TRGSR register before setting the TAiS bit in the TABSR register to 1 (count starts). Always make sure bits TA0TGL and TA0TGH in the TAiMR register, the ONSF register and the TRGSR register are modified while the TAiS bit remains 0 (count stops) regardless whether after reset or not. The IR bit is set to 1 when setting a timer operation mode with any of the following procedures: • Select the PWM mode after reset. • Change an operation mode from timer mode to PWM mode. • Change an operation mode from event counter mode to PWM mode. To use the timer Ai interrupt (interrupt request bit), set the IR bit to 0 by program after the above listed changes have been made. When setting TAiS register to 0 (count stop) during PWM pulse output, the following action occurs: • Stop counting. • When TAiOUT pin is output “H”, output level is set to “L” and the IR bit is set to 1. • When TAiOUT pin is output “L”, both output level and the IR bit remains unchanged. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 195 of 201 M16C/6S Group Usage Notes Serial I/O Clock-Synchronous Serial I/O Transmission/reception With an external clock selected, and choosing the RTS function, the output level of the RTSi pin goes to “L” when the data-receivable status becomes ready, which informs the transmission side that the reception has become ready. The output level of the RTSi pin goes to “H” when reception starts. So if the RTSi pin is connected to the CTSi pin on the transmission side, the circuit can transmission and reception data with consistent timing. With the internal clock, the RTS function has no effect. Transmission When an external clock is selected, the conditions must be met while if the CKPOL bit in the UiC0 register is set to 0 (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock), the external clock is in the high state; if the CKPOL bit in the UiC0 register is set to 1 (transmit data output at the rising edge and the receive data taken in at the falling edge of the transfer clock), the external clock is in the low state. • The TE bit in UiC1 register is set to 1 (transmission enabled) • The TI bit in UiC1 register is set to 0 (data present in UiTB register) • If CTS function is selected, input on the CTSi pin is set to “L” Reception In operating the clock-synchronous serial I/O, operating a transmitter generates a shift clock. Fix settings for transmission even when using the device only for reception. Dummy data is output to the outside from the TxDi pin when receiving data. When an internal clock is selected, set the TE bit in the UiC1 register (i = 0 to 2) to 1 (transmission enabled) and write dummy data to the UiTB register, and the shift clock will thereby be generated. When an external clock is selected, set the TE bit in the UiC1 register (i = 0 to 2) to 1 and write dummy data to the UiTB register, and the shift clock will be generated when the external clock is fed to the CLKi input pin. When successively receiving data, if all bits of the next receive data are prepared in the UARTi receive register while the RE bit in the UiC1 register (i = 0 to 2) is set to 1 (data present in the UiRB register), an overrun error occurs and the UiRB register OER bit is set to 1 (overrun error occurred). In this case, because the content of the UiRB register is undefined, a corrective measure must be taken by programs on the transmit and receive sides so that the valid data before the overrun error occurred will be retransmitted. Note that when an overrun error occurred, the SiRIC register IR bit does not change state. To receive data in succession, set dummy data in the lower-order byte of the UiTB register every time reception is made. When an external clock is selected, make sure the external clock is in high state if the CKPOL bit is set to 0, and in low state if the CKPOL bit is set to 1 before the following conditions are met: • The RE bit in the UiC1 register is set to 1 (reception enabled) • The TE bit in the UiC1 register is set to 1 (transmission enabled) • The TI bit in the UiC1 register= 0 (data present in the UiTB register) Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 196 of 201 M16C/6S Group Usage Notes UART Mode Special Mode 1 (I2C bus Mode) When generating start, stop and restart conditions, set the STSPSEL bit in the U2SMR4 register to 0 and wait for more than half cycle of the transfer clock before setting each condition generate bit (STAREQ, RSTAREQ and STPREQ) from 0 to 1. SI/O3, SI/O4 The SOUTi default value which is set to the SOUTi pin by the SMi7 bit approximately 10ns may be output when changing the SMi3 bit from 0 (I/O port) to 1 (SOUTi output and CLKfunction) while the SMi2 bit in the SiC (i=3 and 4) to 0 (SOUTi output) and the SMi6 bit is set to 1 (internal clock). And then the SOUTi pin is held high-impedance. If the level which is output from the SOUTi pin is a problem when changing the SMi3 bit from 0 to 1, set the default value of the SOUTi pin by the SMi7 bit. Programmable I/O Ports The input threshold voltage of pins differs between programmable input/output ports and peripheral functions. Therefore, if any pin is shared by a programmable input/output port and a peripheral function and the input level at this pin is outside the range of recommended operating conditions VIH and VIL (neither “high” nor “low”), the input level may be determined differently depending on which side—the programmable input/output port or the peripheral function—is currently selected. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 197 of 201 M16C/6S Group Usage Notes Flash Memory Version Functions to Inhibit Rewriting Flash Memory Rewrite ID codes are stored in addresses 0FFFDF16, 0FFFE316, 0FFFEB16, 0FFFEF16, 0FFFF316, 0FFFF716, and 0FFFFB16. If wrong data are written to theses addresses, the flash memory cannot be read or written in standard serial I/O mode. The ROMCP register is mapped in address 0FFFFF16. If wrong data is written to this address, the flash memory cannot be read or written in parallel I/O mode. In the flash memory version of MCU, these addresses are allocated to the vector addresses (“H”) of fixed vectors. The b3 to b0 in address 0FFFFF16 are reserved bits. Set these bits to 11112. Regarding Programming/Erasure Times and Execution Time As the number of programming/erasure times increases, so does the execution time for software commands (Program, and Block Erase). The software commands are aborted by hardware reset 1, brown-out detection reset (hardware reset 2), and watchdog timer interrupt. If a software command is aborted by such reset or interrupt, the affected block must be erased before reexecuting the aborted command. Definition of Programming/Erasure Times “Number of programs and erasure” refers to the number of erasure per block. If the number of program and erasure is n (n=100 1,000) each block can be erased n times. For example, if a 8K byte block A is erased after writing 1 word data 4096 times, each to a different address, this is counted as one program and erasure. However, data cannot be written to the same adrress more than once without erasing the block. (Rewrite prohibited) Boot Mode An undefined value is sometimes output in the I/O port until the internal power supply becomes stable when “H” is applied to the CNVSS pin and “L” is applied to the RESET pin. When setting the CNVSS pin to “H”, the following procedure is required: (1) Apply an “L” signal to the RESET pin and the CNVSS pin. (2) Bring VCC to more than 2.7V, and wait at least 2 msec. (Internal power supply stable waiting time) (3) Apply an “H” signal to the CNVSS pin. (4) Apply an “H” signal to the RESET pin. When the CNVSS pin is “H” and RESET pin is “L”, P67 pin is connected to the pull-up resister. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 198 of 201 M16C/6S Group APPENDIX APPENDIX IT800DLL Explanatory Note June 2, 2005 IT800 Data Link Layer – Functionality and Advantages 1. Scope This document describes the functionality of the Data Link Layer (DLL) implemented in the products based on Yitran's IT800 technology for narrowband networking using the power line wiring. The purpose of this document is to emphasize the advantages of the embedded algorithms and mechanisms of the DLL and to analyze the scenarios of using other implementations of a Data Link Layer. 2. Network Reference Module The DLL is the 2nd layer of the 7 layers in the OSI network reference model illustrated in Figure 1(a). According to this model, data is transported upstream and downstream between subsequent layers, where the communication between layers of different communication nodes is basically carried out between the same layers [Figure 1(b)]. Application Presentation Upper Layers Session Transport Layer 3 Layer 3 Data Transport Layer 2 Network Layer 2 STOP Layer 1 DLL PHY Layer Communication Layer 1 Physical Layers (a) OSI 7 Layers Model (b) Data Transport and Layer Communication Figure 1: Network Reference Model The Physical Layer (PHY) defines the electrical specifications for activating, the physical link between the communicating network system nodes. The DLL algorithms are designed to establish and manage a unique access channel between any two nodes as optimally and fairly as possible while minimizing the probability of collisions. The IT800 DLL was developed by Yitran especially for the IT800 PHY and using the DLL optimize the utilization of the PHY and thus optimizes the overall performance. The IT800 DLL implementation manages the time critical sessions of the interface with the PHY and uses the knowledge of the PHY implementation for optimal interrupt decoding and efficient interface interactions. The DLL takes advantage of various PHY features such as multiple transportation modes and the ability to create special packets and signals, enabling optimal utilization of the media channel while providing the most reliable data transfer. Copyright © 2005, YITRAN Communications Ltd. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 199 of 201 M16C/6S Group APPENDIX IT800DLL Explanatory Note June 2, 2005 3. IT800DLL Main functions The DLL main functions and mechanisms are described in the following table: Function Description Carrier sense Provides the carrier detection (CD) signal for triggering the media access algorithms as a function of the PHY correlator output, which indicates the probability of a signal on the line. Channel access prioritization Determines the sequence and time of packet transmissions for a PLC node, where the highest priority packet nodes participate in the DLL contention for the media access. Adaptive back-off Spreads the time over which a PLC node contends for the channel using a uniform distribution of the transmissions number over a given period of time (Yitran patent pending). This mechanism provides high efficiency of the network functionality, optimal utiliziation of the channel and sustains a viable network even in cases where many nodes contend for the channel simultaneously. Acknowledgement Serves for informing the transmitting node about the success or failure of a packet delivery to a target node by means of a traffic-free acknowledgement window. Repetitive unacknowledgement This mechanism is used for transmitting packets a pre-determined number of times without requiring a reception acknowledgement from the target node. Multiple hop broadcast Retransmits single-network broadcast packets and CNC (Control Network Channel) messages to all the nodes participating in the same logical network. Fragmentation and reassembly Transfers packets longer than the maximal packet size allowed by the PHY by means of fragmentation in the transmitting node and reassembly in the receiving node Packet filtering Filters received packets according to their type for transferring only pre-defined types of messages to the upper layers and rejecting impostor node or other types of messages that are not required. As can be seen from the table above, the IT800 DLL implements enhanced functionality, provides best performance in terms of channel access and throughput (based on Carrier Sense signaling, Adaptive Back-off algorithm and packet prioritization), reliable data transfer (using acknowledgement and repetition mechanisms, multi-hop transmissions and packet filtering) and allows easy integration of IT800 based solution with different protocol stacks. Another important advantage of using IT800DLL is assuring the co-existence between different IT800 based products operating in the same environment. Copyright © 2005, YITRAN Communications Ltd. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 200 of 201 M16C/6S Group APPENDIX IT800DLL Explanatory Note June 2, 2005 4. Other DLL implementations In case of using other implementations of the DLL or considering such implementations, please be advised to consider the following issues: 1. Co-existence: Implementing a different channel access scheme, prioritization levels, packet formats and so forth, will not allow your product to co-exist with other IT800 based products that may share the same medium. Using the IT800 will enable such co-existence regardless of the product, the vendor, the application and the protocol used in top of the DLL. 2. Required Knowledge, Time to Market and Cost: Interfacing the DLL is much easier than interfacing the PHY. Physical layer interface includes handling of a several interrupts, critical timing sections and so forth. To be able to do so you require very good understanding of the both the power line medium and the PHY internal mechanisms and will significantly increase the development resources and schedule and as a result the time to market and product cost. In addition note that not all the PHY internal mechanism can be disclosed as some are in the status of patent-pending. 3. Overall performance: IT800DLL has been tested and integrated into different Control and Automation products over many years. The implementation has showed the best performance for Narrowband Power Line communication modem, when all the algorithms implemented in it were verified using the networking simulations and in real systems. 5. Summary As a conclusion, we highly recommend to using IT800 DLL implementation in all type of products using the IT800 PHY, rather than using the latter by itself. In case you still wish to self implement the DLL layer, please be sure to consult RENESAS support engineers. Copyright © 2005, YITRAN Communications Ltd. Rev.5.01 Dec 10, 2009 REJ03B0014-0501 page 201 of 201 REVISION HISTORY Rev. M16C/6S Group Date Description Summary Page 1.00 Jun 25, 2003 - 2.00 Aug 18, 2003 P1 P2 P3 P4 P5 P7 P8 P9 P12 P14 P15 P20 P24 P25 P26 P27 P29 P30 P33 P36 P37 P42 P43 P45 P52 P54 P62 P83 P84 P85 P88 P90 P92 P94 P95 P100 P107 P119 First edition issued L7 is changed. T1.1.1 is changed. F1.1.1 is changed. T1.1.2 is changed. F1.1.2 is changed. T1.1.3 is changed. T1.1.4 is changed. L5 and F1.2.1 are changed. Table of register is changed. Table of register is changed. Table of register is changed. F1.5.2 is changed. F1.6.1 is changed. F1.6.2 is changed. F1.6.3 is changed. L2 and F1.7.1 are changed. F1.7.2 is changed. F1.7.3 is changed. L4 to L5 and F1.7.6 are changed. L5 is changed. T1.7.2 is changed. F1.7.8 is changed. T1.7.6 is changed. T1.7.7 is changed. T1.9.2 is changed. T1.9.3 is changed. L2 is changed. F1.12.5 is changed. F1.12.6 is changed. L3 and T1.12.2 are changed. F1.12.8 is changed. F1.12.9 is changed. F1.12.10 is changed. L13 is changed. F1.13.1 is changed. F1.13.6 is changed. F1.14.2 and F1.14.3 are changed. T1.16.2 is changed. A- 1 Rev. Date Description Summary Page 2.00 Aug 18, 2003 P121 PT1.16.4 is changed. P127 T1.16.6 is changed. P128 F1.16.5 is changed. – Special Mode 3 is delated. P139 L10 to L11 and L17 to L19 and L21 and L30 to L32 and L38 to L40 are changed. P140 F1.18.1 is changed. P141 F1.18.2 is changed. P143 F1.18.4 is changed. P147 F1.18.8 is changed. P149 T1.18.1 is changed. P151 T1.19.1 is changed. P152 T1.19.2 is changed. P153 T1.19.4 is changed. P154 T1.19.5 is changed. P155 T1.19.6 is changed. P157 L2 and T1.19.8 are changed. P158 L2 is changed. P159 L2 is changed. P162 L3 to L4 are delated. T1.20.2 is changed. P163 1.Memory Map is changed. F1.20.1 is changed. P164 Boot Mode is changed. P166 L5 and T1.21.1 are changed. P168 is changed. P169 F1.21.2 is changed. P170 F1.21.3 is changed. P171 F1.21.4 is changed. P174 T1.21.2 is changed. Read Array Command is changed. P175 Program Command is changed. P176 Block Erase is changed. P177 Sequencer Status and T1.21.3 are changed. P178 T1.21.4 is changed. P179 F1.21.7 is changed. P181 T1.22.1 is changed. P182 F1.22.1 is changed. P183 F1.22.2 is changed. P184 Parallel I/O Mode and User ROM and Boot ROM Areas are delated. A- 2 Rev. Date Description Summary Page 2.01 Oct 27, 2003 P3 P7 P22 P23 P141 P143 P144 P178 3.00 Jul 22, 2004 P1 P2 P4 P5 P6 P7 P9 P22 P23 P26 P27 P32 P33 P36 P37 P38 P44 P45 P46 P48 P49 P55 P58 P59 Between P60 to P61 P63 P79 P137 P140 P147 P148 P149 P150 P151 P152 L1 to L2 are changed. F1.1.1 is changed. T1.1.3 is changed. L3 to L4 are changed. (3) Setting PLC Mode is changed. T1.6.4 and F1.6.1 and F1.6.2 are changed. F1.18.4 is changed. F1.18.6 is changed. F1.18.7 is changed. Standard Serial I/O Mode is changed. Table of Contents is changed. T1.1.1 is changed. T1.1.2 is changed. F1.1.2 is changed. F1.1.3 is changed. T1.1.3 is changed. F1.2.1 is changed. Text is changed. T1.6.1 is delated. Text is changed. T1.6.4 and F1.6.2 are delated. Table name of T1.6.3 is added. T1.7.1 is changed. F1.7.1 is changed. Text is changed. F1.7.6 is changed. Text is changed. Text is changed. T1.7.4 is changed. Text is changed. T1.7.7, F1.7.9 and text are delated. Text is changed. F1.9.1 is changed. Text is changed (NMI Interrupt is delated.) T1.9.1 is changed. T1.9.5 is changed. F.1.9.8 is changed. F.1.9.9 is changed. Text is delated (NMI Interrupt is delated.) Text is delated (NMI Interrupt is delated.) F.1.12.4 is changed. Text is changed. F.1.18.3 is changed. T.1.18.1 is changed. F.1.18.10 is changed. T.1.19.1 is changed. T.1.19.2 is changed. Deletion of a voltage desplay of a header. Deletion of a voltage desplay of a header. Deletion of a voltage desplay of a header. A- 3 Rev. Date Description Summary Page 3.00 Jul 22, 2004 3.01 Feb 17, 2005 4.00 Aug 05, 2005 P153 T.1.19.6 is changed. Deletion of a voltage desplay of a header. P154 T.1.19.7 is changed. Deletion of a voltage desplay of a header. 155 Deletion of a voltage desplay of a header. P156 Deletion of a voltage desplay of a header. P157 T.1.19.15 is changed. P163 T.1.20.3 is changed. P167 T.1.21.2 is changed. P168 T.1.21.3 is changed. P169 T.1.21.4 is changed. P170 Text is changed. P180 IT800AFE (Analog Front End) is added. P181 F.1.23.2 is changed. P183 Text is changed. T.1.23.2 is changed. P184 F.1.23.4 is changed. - Words standardized (On-chip Oscillator). P7 T.1.1.3 addition and changed. P34 L11-L12 addition and changed. P38 L2-L5 addition and delated. P42 T.1.7.6 part of delated. P157 L19 is delated. P1 Text is changed. P5 F.1.1.2 is changed. T.1.1.3 and F.1.1.3 are added. P7 T.1.1.4 is changed. P56 F.1.9.6 is changed. P57 F.1.9.7 is changed. P61 Text is changed. F.1.9.11 is changed. P66 Text is changed. F.1.10.1 is changed. P77 F.1.12.1 is changed. P78 F.1.12.2 is changed. P84 T.1.12.3 is changed. P85 F.1.12.8 is changed. P86 P86 is added. P88 T.1.12.5 is changed. P93 F.1.13.1 is changed. P94 F.1.13.2 is changed. P97 F.1.13.5 is changed. P105 L1-L13 are added. P106 L5-L8 are added. P108 L1-L11 are added. A- 4 Rev. Date Description Summary Page 4.00 Aug 05, 2005 P110 T.1.15.2 is changed. P114 L1-L11 are added. P116 L1-L10 are added. P118 F.1.16.1 is changed. P119 T.1.16.2 is changed. P121 T.1.16.4 is changed. P123 L8-L16 are added. P130 Text is changed. P137 L2, L5-L6 and L12 are changed. P147 Note is added. P151 T.1.19.3 is changed. P160 T.1.20.1 is changed. P165 L12-L13 are added. P176 T.1.21.4 is changed. P188 to Appendix is added. P190 5.00 Apr 24, 2009 1 Overview “AMR (Automatic Meter Reading)” → “smart metering” 2 Table 1.1.1 Operating Ambient Temperature “-40 to 105°C” is added. 3 Table 1.1.2 “Error Correction” → “Error Correction/Detection” About Firmware “(Product name: D2DL)” is added. 5 Table 1.1.3 is revised. Table 1.1.4 is added. Figure 1.1.2 is revised. 6 Table 1.1.5 and 1.1.6 are added. Figure 1.1.3 is revised. 8 Table 1.1.7 P85 is revised. 13 Address 000416 After reset “000000002” → “XXXX0X002” Address 000516 After reset “000010002” → “00XX10102” 24 Table 1.6.3 title is added. 25 Figure 1.6.2 After reset “000000002” → “XXXX0X002” “000000112 (CNVSS pin =“H”)” is deleted. Figure 1.6.3 After reset “0X0010002” → “00XX10X02” 28 Figure 1.7.1 is revised. 33 (1) Main Clock “Xin” → “XIN” 41 “Figure 1.7.8...transition.” is deleted. 42 Figure 1.7.8 Note 1 to Note 4 are revised. 61 Figure 1.9.10 Note 1 “INT5IC” → “INT3IC” 66 Watchdog Timer “If a sub-clock is...no matter how the WDC7 bit is set.” is deleted. 78 Figure 1.12.1 is revised. A- 5 Rev. Date Description Summary Page 5.00 Apr 24, 2009 92 “UARTi (i=0 to 2)” is revised. 117 Table 1.16.1 “Error detection” is revised. 147 Table 1.18.1 title “(Excluding Analog Pins)” is added. 148 Figure 1.18.10 title “(Excluding Analog Pins)” is added. 149 Table 1.19.1 Topr is revised, Note 1 is revised. 150 Table 1.19.2 “VCC1” → “VCC” , Note 1 is revised. 152 Table 1.19.5 Note is deleted. 153 Table 1.19.6 Note is revised. 154 Table 1.19.7 Standard “95” is added. Note is revised. 155 to 157 Timing Requirements “-20 to 85°C” → “-20 to 85°C/-40 to 85°C/-40 to 105°C” 160 parallel writer → parallel programmer Table 1.20.1 “Block 0 to 5” → “Block 0 to 4” “See Figure 20.2.1 to 20.2.3” → “See Figure 1.20.1” 161 “The boot ROM area is located ... in parallel input/output mode.” → “The boot 164 “In CPU mode, only the user ROM area ... the boot ROM area cannot be rewritten.” is deleted. 178 Standard Serial I/O Mode “The main clock f1 is 5.12 MHz in this mode.” is added. 180 serial writer → serial programmer 183 (1)Transmitting path is revised. 184 Table 1.23.1 title “-20 to 85°C” → “-20 to 85°C/-40 to 85°C/-40 to 105°C” 186 Table 1.23.2 title “-25°C” → “25°C” 187 Figure 1.23.4 is revised. ROM area is reserved. The rewrite control program ... the area cannot be rewritten.” 188 to 197 “Usage Notes” is added. 200 5.01 Dec 10, 2009 4. Other DLL implementations “the last three years” → “many years” 2 Table 1.1.1 Memory Capacity; ROM is revised 5 Table 1.1.4 “M306S0F8DGP” is added, Figure 1.1.2 ROM capacity “8: 64K bytes” is added 10 Figure 1.2.1 Internal ROM “64K bytes” is added, Note 1 is revised 26 Figure 1.6.4 Internal ROM “64K bytes” is added 161 Figure 1.20.1 is added 162 Figure 1.20.2 title “(ROM Capacity 96K bytes)” is added. A-6 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7858/7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2377-3473 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 3518-3399 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 © 2009. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .7.2