RENESAS M32C88

REJ09B0162-0110
16/32
M32C/88 Group (M32C/88T)
Hardware Manual
RENESAS 16/32-BIT SINGLE-CHIP MICROCOMPUTER
M16C FAMILY / M32C/80 SERIES
Before using this material, please visit our website to verify that this is the most
current document available.
Rev. 1.10
Revision Date: Oct. 18, 2005
www.renesas.com
Keep safety first in your circuit designs!
1.
Renesas Technology Corp. puts the maximum effort into making semiconductor products
better and more reliable, but there is always the possibility that trouble may occur with
them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1.
2.
3.
4.
5.
6.
7.
8.
These materials are intended as a reference to assist our customers in the selection of the
Renesas Technology Corp. product best suited to the customer's application; they do not
convey any license under any intellectual property rights, or any other rights, belonging to
Renesas Technology Corp. or a third party.
Renesas Technology Corp. assumes no responsibility for any damage, or infringement of
any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these
materials, and are subject to change by Renesas Technology Corp. without notice due to
product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other
loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://
www.renesas.com).
When using any or all of the information contained in these materials, including product
data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information
and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein.
Renesas Technology Corp. semiconductors are not designed or manufactured for use in a
device or system that is used under circumstances in which human life is potentially at
stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology
Corp. product distributor when considering the use of a product contained herein for any
specific purposes, such as apparatus or systems for transportation, vehicular, medical,
aerospace, nuclear, or undersea repeater use.
The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
If these products or technologies are subject to the Japanese export control restrictions,
they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/
or the country of destination is prohibited.
Please contact Renesas Technology Corp. for further details on these materials or the
products contained therein.
How to Use This Manual
1. Introduction
This hardware manual provides detailed information on the M32C/88 Group (M32C/88T) microcomputer.
Users are expected to have basic knowledge of electric circuits, logical circuits and microcomputers.
2. Register Diagram
The symbols, and descriptions, used for bit function in each register are shown below.
XXX Register
b7
b6
b5
b4
b3
b2
*1
b1
b0
0 0
Symbol
XXX
Address
After Reset
XXX
0016
Bit Name
Bit Symbol
Function
RW
*2
b1 b0
XXX0
XXX bit
XXX1
(b2)
0 0: XXX
0 1: XXX
1 0: Do not set a value
1 1: XXX
RW
Nothing is assigned.
When write, set to "0". When read, its content is indeterminate.
Reserved bit
(b4 - b3)
Set to "0"
*3
WO
*4
XXX5
XXX bit
Function varies depending on mode
of operation
RW
RW
XXX6
XXX7
RW
XXX bit
0: XXX
1: XXX
RO
*1
Blank:Set to "0" or "1" according to the application
0:
Set to "0"
1:
Set to "1"
X:
Nothing is assigned
*2
RW:
RO:
WO:
–:
Read and write
Read only
Write only
Nothing is assigned
*3
• Reserved bit
Reserved bit. Set to specified value.
*4
• Nothing is assigned
Nothing is assigned to the bit concerned. As the bit may be use for future functions,
set to "0" when writing to this bit.
• Do not set a value
The operation is not guaranteed when a value is set.
• Function varies depending on mode of operation
Bit function varies depending on peripheral function mode.
Refer to respective register for each mode.
3. M16C Family Documents
The following documents were prepared for the M16C family. (1)
Document
Short Sheet
Data Sheet
Hardware Manual
Contents
Hardware overview
Hardware overview and electrical characteristics
Hardware specifications (pin assignments, memory maps, peripheral
specifications, electrical characteristics, timing charts)
Software Manual
Detailed description of assembly instructions and microcomputer performance of each instruction
Application Note
• Application examples of peripheral functions
• Sample programs
• Introduction to the basic functions in the M16C family
• Programming method with Assembly and C languages
RENESAS TECHNICAL UPDATE Preliminary report about the specification of a product, a document, etc.
NOTES :
1. Before using this material, please visit the our website to verify that this is the most current document
available.
Table of Contents
Quick Reference by Address _______________________ 1
1. Overview _____________________________________ 1
1.1
1.2
1.3
1.4
1.5
1.6
Applications ................................................................................................................ 1
Performance Overview .............................................................................................. 2
Block Diagram ............................................................................................................ 4
Product Information ................................................................................................... 5
Pin Assignment .......................................................................................................... 7
Pin Description ......................................................................................................... 14
2. Central Processing Unit (CPU) __________________ 17
2.1 General Registers .................................................................................................... 18
2.1.1 Data Registers (R0, R1, R2 and R3) ................................................................. 18
2.1.2 Address Registers (A0 and A1) ....................................................................... 18
2.1.3 Static Base Register (SB) ................................................................................. 18
2.1.4 Frame Base Register (FB) ................................................................................ 18
2.1.5 Program Counter (PC) ...................................................................................... 18
2.1.6 Interrupt Table Register (INTB) ........................................................................ 18
2.1.7 User Stack Pointer (USP), Interrupt Stack Pointer (ISP) ............................... 18
2.1.8 Flag Register (FLG) ........................................................................................... 18
2.2 High-Speed Interrupt Registers .............................................................................. 19
2.3 DMAC-Associated Registers ................................................................................... 19
3. Memory _____________________________________ 20
4. Special Function Registers (SFRs)_______________ 21
5. Reset _______________________________________ 45
5.1 Hardware Reset 1 ..................................................................................................... 45
5.1.1 Reset on a Stable Supply Voltage .................................................................... 45
5.1.2 Power-on Reset .................................................................................................. 45
5.2 Software Reset ......................................................................................................... 47
5.3 Watchdog Timer Reset ............................................................................................ 47
5.4 Internal Space ........................................................................................................... 47
6. Cold Start-up/Warm Start-up Determine Function __ 48
7. Processor Mode ______________________________ 50
7.1 Types of Processor Mode ........................................................................................ 50
7.2 Setting of Processor Mode ...................................................................................... 50
A-1
8. Clock Generation Circuit _______________________ 54
8.1 Types of the Clock Generation Circuit ................................................................... 54
8.1.1 Main Clock ......................................................................................................... 63
8.1.2 Sub Clock .......................................................................................................... 64
8.1.3 On-Chip Oscillator Clock ................................................................................. 65
8.1.4 PLL Clock .......................................................................................................... 67
8.2 CPU Clock and BCLK .............................................................................................. 68
8.3 Peripheral Function Clock ....................................................................................... 68
8.3.1 f1, f8, f32 and f2n ......................................................................................................................... 68
8.3.2 fAD .................................................................................................................................................... 68
8.3.3 fC32 ................................................................................................................................................... 69
8.3.4 fCAN .................................................................................................................................................. 69
8.4 Clock Output Function ............................................................................................ 69
8.5 Power Consumption Control .................................................................................. 70
8.5.1 Normal Operating Mode ................................................................................... 70
8.5.2 Wait Mode .......................................................................................................... 71
8.5.3 Stop Mode .......................................................................................................... 73
8.6 System Clock Protect Function .............................................................................. 77
9. Protection ___________________________________ 78
10. Interrupts___________________________________ 79
10.1 Types of Interrupts ................................................................................................. 79
10.2 Software Interrupts ................................................................................................ 80
10.2.1 Undefined Instruction Interrupt ..................................................................... 80
10.2.2 Overflow Interrupt ........................................................................................... 80
10.2.3 BRK Interrupt .................................................................................................. 80
10.2.4 BRK2 Interrupt ................................................................................................ 80
10.2.5 INT Instruction Interrupt ................................................................................. 80
10.3 Hardware Interrupts ............................................................................................... 81
10.3.1 Special Interrupts ............................................................................................ 81
10.3.2 Peripheral Function Interrupt ........................................................................ 81
10.4 High-Speed Interrupt ............................................................................................. 82
10.5 Interrupts and Interrupt Vectors ........................................................................... 82
10.5.1 Fixed Vector Tables ........................................................................................ 83
10.5.2 Relocatable Vector Tables .............................................................................. 83
10.6 Interrupt Request Acknowledgement ................................................................... 86
10.6.1 I Flag and IPL ................................................................................................... 86
10.6.2 Interrupt Control Register and RLVL Register ............................................. 86
10.6.3 Interrupt Sequence ......................................................................................... 90
A-2
10.6.4 Interrupt Response Time ................................................................................ 91
10.6.5 IPL Change when Interrupt Request is Acknowledged ............................... 92
10.6.6 Saving a Register ............................................................................................ 93
10.6.7 Restoration from Interrupt Routine ............................................................... 93
10.6.8 Interrupt Priority .............................................................................................. 94
10.6.9 Interrupt Priority Level Select Circuit ........................................................... 94
______
10.7 INT Interrupt ............................................................................................................ 96
______
10.8 NMI Interrupt ........................................................................................................... 97
10.9 Key Input Interrupt ................................................................................................. 97
10.10 Address Match Interrupt ...................................................................................... 98
10.11 Intelligent I/O Interrupt and CAN Interrupt ......................................................... 99
11. Watchdog Timer ____________________________ 103
11.1 Count Source Protection Mode ........................................................................... 106
12. DMAC_____________________________________ 107
12.1 Transfer Cycle ...................................................................................................... 114
12.1.1 Effect of Source and Destination Addresses ............................................. 114
12.1.2 Effect of Software Wait State ....................................................................... 114
12.2 DMAC Transfer Cycle ........................................................................................... 116
12.3 Channel Priority and DMA Transfer Timing ....................................................... 116
13. DMAC II ___________________________________ 118
13.1 DMAC II Settings .................................................................................................. 118
13.1.1 RLVL Register................................................................................................ 118
13.1.2 DMAC II Index ................................................................................................ 120
13.1.3 Interrupt Control Register for the Peripheral Function ............................. 122
13.1.4 Relocatable Vector Table for the Peripheral Function ............................... 122
13.1.5 IRLT Bit in the IIOiIE Register (i=0 to 6, 8 to 11) ......................................... 122
13.2 DMAC II Performance .......................................................................................... 122
13.3 Transfer Data ........................................................................................................ 122
13.3.1 Memory-to-memory Transfer ....................................................................... 122
13.3.2 Immediate Data Transfer .............................................................................. 123
13.3.3 Calculation Transfer ..................................................................................... 123
13.4 Transfer Modes ..................................................................................................... 123
13.4.1 Single Transfer .............................................................................................. 123
13.4.2 Burst Transfer ............................................................................................... 123
13.5 Multiple Transfer .................................................................................................. 123
13.6 Chained Transfer .................................................................................................. 124
13.7 End-of-Transfer Interrupt ..................................................................................... 124
13.8 Execution Time ..................................................................................................... 125
A-3
14. Timer _____________________________________ 126
14.1 Timer A .................................................................................................................. 128
14.1.1 Timer Mode .................................................................................................... 134
14.1.2 Event Counter Mode ..................................................................................... 136
14.1.3 One-Shot Timer Mode ................................................................................... 140
14.1.4 Pulse Width Modulation Mode ..................................................................... 142
14.2 Timer B .................................................................................................................. 145
14.2.1 Timer Mode .................................................................................................... 148
14.2.2 Event Counter Mode ..................................................................................... 149
14.2.3 Pulse Period/Pulse Width Measurement Mode .......................................... 151
15. Three-Phase Motor Control Timer Functions ____ 154
16. Serial I/O __________________________________ 165
16.1 Clock Synchronous Serial I/O Mode .................................................................. 175
16.1.1 Selecting CLK Polarity Selecting ................................................................ 179
16.1.2 Selecting LSB First or MSB First ................................................................. 179
16.1.3 Continuous Receive Mode ........................................................................... 180
16.1.4 Serial Data Logic Inverse ............................................................................. 180
16.2 Clock Asynchronous Serial I/O (UART) Mode ................................................... 181
16.2.1 Bit Rate .......................................................................................................... 185
16.2.2 Selecting LSB First or MSB First ................................................................. 186
16.2.3 Serial Data Logic Inverse ............................................................................. 186
16.2.4 TxD and RxD I/O Polarity Inverse ................................................................ 187
16.3 Special Mode 1 (I2C Mode) .................................................................................. 188
16.3.1 Detecting Start Condition and Stop Condition .......................................... 194
16.3.2 Start Condition or Stop Condition Output .................................................. 194
16.3.3 Arbitration ...................................................................................................... 196
16.3.4 Transfer Clock ............................................................................................... 196
16.3.5 SDA Output .................................................................................................... 196
16.3.6 SDA Input ....................................................................................................... 197
16.3.7 ACK, NACK .................................................................................................... 197
16.3.8 Transmit and Receive Reset ........................................................................ 197
16.4 Special Mode 2 ..................................................................................................... 198
______
16.4.1 SSi Input Pin Function (i=0 to 4) .................................................................. 201
16.4.2 Clock Phase Setting Function ..................................................................... 202
16.5 Special Mode 3 (GCI Mode) ................................................................................. 204
16.6 Special Mode 4 (IE Mode) .................................................................................... 208
A-4
16.7 Special Mode 5 (SIM Mode) ................................................................................. 212
16.7.1 Parity Error Signal ........................................................................................ 216
16.7.2 Format ............................................................................................................ 217
17. A/D Converter ______________________________ 218
17.1 Mode Description ................................................................................................. 226
17.1.1 One-shot Mode .............................................................................................. 226
17.1.2 Repeat Mode .................................................................................................. 227
17.1.3 Single Sweep Mode ...................................................................................... 228
17.1.4 Repeat Sweep Mode 0 .................................................................................. 229
17.1.5 Repeat Sweep Mode 1 .................................................................................. 230
17.1.6 Multi-Port Single Sweep Mode ..................................................................... 231
17.1.7 Multi-Port Repeat Sweep Mode 0 ................................................................ 232
17.2 Functions .............................................................................................................. 233
17.2.1 Resolution Select Function .......................................................................... 233
17.2.2 Sample and Hold Function ........................................................................... 233
17.2.3 Trigger Select Function ................................................................................ 233
17.2.4 DMAC Operating Mode ................................................................................. 233
17.2.5 Extended Analog Input Pins ........................................................................ 234
17.2.6 External Operating Amplifier (Op-Amp) Connection Mode....................... 234
17.2.7 Power Consumption Reducing Function ................................................... 235
17.2.8 Output Impedance of Sensor Equivalent Circuit under A/D Conversion ... 235
18.
19.
20.
21.
D/A Converter ______________________________
CRC Calculation ____________________________
X/Y Conversion _____________________________
Intelligent I/O_______________________________
237
240
242
245
21.1 Base Timer ............................................................................................................ 254
21.2 Time Measurement Function............................................................................... 259
21.3 Waveform Generating Function .......................................................................... 264
21.3.1 Single-Phase Waveform Output Mode ........................................................ 265
21.3.2 Phase-Delayed Waveform Output Mode ..................................................... 267
21.3.3 Set/Reset Waveform Output (SR Waveform Output) Mode ....................... 269
21.4 Communication Unit 0 and 1 Communication Function .................................. 272
21.4.1 Clock Synchronous Serial I/O Mode (Communication Units 0 and 1) ..... 282
21.4.2 Clock Asynchronous Serial I/O (UART) Mode (Communication Unit 1) .. 286
21.4.3 HDLC Data Processing Mode (Communication Units 0 and 1) ................ 289
A-5
22. CAN Module _______________________________ 292
22.1 CAN-Associated Registers .................................................................................. 296
22.1.1 CANi Control Register 0 (CiCTLR0 Register) (i=0 to 2) ............................. 296
22.1.2 CANi Control Register 1 (CiCTLR1 Register) (i=0 to 2) ............................. 299
22.1.3 CANi Sleep Control Register (CiSLPR Register) (i=0 to 2) ....................... 300
22.1.4 CANi Status Register (CiSTR Register) (i=0 to 2) ...................................... 301
22.1.5 CANi Extended ID Register (CiIDR Register) (i=0 to 2) ............................. 304
22.1.6 CANi Configuration Register (CiCONR Register) (i=0 to 2) ...................... 305
22.1.7 CANi Baud Rate Prescaler (CiBRP Register) (i=0 to 2) ............................. 307
22.1.8 CANi Time Stamp Register (CiTSR Register) (i=0 to 2) ............................. 308
22.1.10 CANi Receive Error Count Register (CiREC Register) (i=0 to 2) ............ 309
22.1.9 CANi Transmit Error Count Register (CiTEC Register) (i=0 to 2) ............. 309
22.1.11 CANi Slot Interrupt Status Register (CiSISTR Register) (i=0 to 2).......... 310
22.1.12 CANi Slot Interrupt Mask Register (CiSIMKR Register) (i=0 to 2) .......... 312
22.1.13 CANi Error Interrupt Mask Register (CiEIMKR Register) (i=0 to 2) ........ 313
22.1.14 CANi Error Interrupt Status Register (CiEISTR Register) (i=0 to 2) ....... 314
22.1.15 CANi Error Factor Register (CiEFR Register) (i=0 to 2) .......................... 315
22.1.16 CANi Mode Register (CiMDR Register) (i=0 to 2) ..................................... 316
22.1.17 CANi Single-Shot Control Register (CiSSCTLR Register) (i=0 to 2) ...... 318
22.1.18 CANi Single-Shot Status Register (CiSSSTR Register) (i=0 to 2) .......... 319
22.1.19 CANi Global Mask Register, CANi Local Mask Register A and CANi Local Mask
Register B (CiGMRk, CiLMARk and CiLMBRk Registers) (i=0 to 2, k=0 to 4) ... 320
22.1.20 CANi Message Slot j Control Register (CiMCTLj Register) (i=0 to 2, j=0 to 15). 327
22.1.21 CANi Slot Buffer Select Register (CiSBS Register) (i=0 to 2) ................. 331
22.1.22 CANi Message Slot Buffer j (i=0 to 2, j=0,1) .............................................. 332
22.1.23 CANi Acceptance Filter Support Register (CiAFS Register) (i=0 to 2) ... 336
22.2 CAN Clock ............................................................................................................. 337
22.2.1 Main Clock Direct Mode ............................................................................... 337
22.3 Timing with CAN-Associated Registers ............................................................. 338
22.3.1 CAN Module Reset Timing ........................................................................... 338
22.3.2 CAN Transmit Timing ................................................................................... 338
22.3.3 CAN Receive Timing ..................................................................................... 339
22.3.4 CAN Bus Error Timing .................................................................................. 340
22.4 CAN Interrupts ...................................................................................................... 340
22.4.1 CANi Wake-Up Interrupt ............................................................................... 340
22.4.2 CANij Interrupts ............................................................................................ 341
22.5 CAN0/CAN2 Combination Mode ......................................................................... 344
22.5.1 Notes for CAN0/CAN2 Combination Mode ................................................. 345
A-6
23. Programmable I/O Ports _____________________ 346
23.1 Port Pi Direction Register (PDi Register, i=0 to 15)........................................... 346
23.2 Port Pi Register (Pi Register, i=0 to 15) .............................................................. 346
23.3 Function Select Register Aj (PSj Register) (j=0 to 3, 5, 8, 9) ............................ 346
23.4 Function Select Register B0 to B3 (PSL0 to PSL3 Registers) ......................... 346
23.5 Function Select Register C, C2, C3 (PSC, PSC2, PSC3 Registers) ................. 346
23.6 Function Select Register D (PSD1 Register) ..................................................... 347
23.7 Pull-up Control Register 0 to 4 (PUR0 to PUR4 Registers) .............................. 347
23.8 Port Control Register (PCR Register) ................................................................ 347
23.9 Input Function Select Register (IPS and IPSA Registers) ................................ 347
23.10 Analog Input and Other Peripheral Function Input ......................................... 347
24. Flash Memory Version _______________________ 369
24.1 Memory Map ......................................................................................................... 370
24.1.1 Boot Mode ..................................................................................................... 371
24.2 Functions to Prevent Rewriting of Flash Memory ............................................ 371
24.2.1 ROM Code Protect Function ........................................................................ 371
24.2.2 ID Code Verify Function ............................................................................... 371
24.3 CPU Rewrite Mode ............................................................................................... 373
24.3.1 EW Mode 0 ..................................................................................................... 373
24.3.2 EW Mode 1 ..................................................................................................... 373
24.3.3 Flash Memory Control Register (FMR0 Register and FMR1 Register) .... 374
24.3.4 Precautions in CPU Rewrite Mode .............................................................. 380
24.3.5 Software Commands .................................................................................... 382
24.3.6 Data Protect Function ................................................................................... 388
24.3.7 Status Register (SRD Register) ................................................................... 388
24.3.8 Full Status Check .......................................................................................... 390
24.4 Standard Serial I/O Mode ..................................................................................... 392
24.4.1 ID Code Verify Function ............................................................................... 392
24.4.2 Circuit Application in Standard Serial I/O Mode ........................................ 396
24.5 Parallel I/O Mode .................................................................................................. 398
24.5.1 Boot ROM Area.............................................................................................. 398
24.5.2 ROM Code Protect Function ........................................................................ 398
25. Electrical Characteristics ____________________ 399
26. Precautions ________________________________ 411
26.1 Special Function Registers (SFRs) .................................................................... 411
26.1.1 100-Pin Package ............................................................................................ 411
26.1.2 Register Settings .......................................................................................... 411
A-7
26.2 Clock Generation Circuit ..................................................................................... 412
26.2.1 CPU Clock...................................................................................................... 412
26.2.2 Sub Clock ...................................................................................................... 412
26.2.3 PLL Frequency Synthesizer ......................................................................... 413
26.2.4 External Clock ............................................................................................... 413
26.2.5 Clock Divide Ratio ........................................................................................ 413
26.2.6 Power Consumption Control ....................................................................... 413
26.3 Protection ............................................................................................................. 416
26.4 Interrupts .............................................................................................................. 417
26.4.1 ISP Setting ..................................................................................................... 417
_______
26.4.2 NMI Interrupt .................................................................................................. 417
______
26.4.3 INT Interrupt .................................................................................................. 417
26.4.4 Watchdog Timer Interrupt ............................................................................ 418
26.4.5 Changing Interrupt Control Register .......................................................... 418
26.4.6 Changing IIOiIR Register (i = 0 to 6, 8 to 11) .............................................. 418
26.4.7 Changing RLVL Register .............................................................................. 418
26.5 DMAC .................................................................................................................... 419
26.6 Timer...................................................................................................................... 420
26.6.1 Timers A and B .............................................................................................. 420
26.6.2 Timer A ........................................................................................................... 420
26.6.3 Timer B ........................................................................................................... 422
26.7 Serial I/O ................................................................................................................ 423
26.7.1 Clock Synchronous Serial I/O Mode ........................................................... 423
26.7.2 UART Mode .................................................................................................... 424
26.7.3 Special Mode 1 (I2C Mode) ........................................................................... 424
26.8 A/D Converter ....................................................................................................... 425
26.9 Intelligent I/O ........................................................................................................ 427
26.9.1 Register Setting ............................................................................................ 427
26.10 Programmable I/O Ports .................................................................................... 428
26.11 Flash Memory Version ....................................................................................... 429
26.11.1 Boot Mode .................................................................................................... 429
26.12 Noise ................................................................................................................... 430
Package Dimensions ___________________________ 431
Register Index _________________________________ 432
A-8
Quick Reference by Address
Address
000016
000116
000216
000316
000416
000516
000616
000716
000816
000916
000A16
000B16
000C16
000D16
000E16
000F16
001016
001116
001216
001316
001416
001516
001616
001716
001816
001916
001A16
001B16
001C16
001D16
001E16
001F16
002016
002116
002216
002316
002416
002516
002616
002716
002816
002916
002A16
002B16
002C16
002D16
002E16
002F16
Register
Page
Processor Mode Register 0 (PM0)
Processor Mode Register 1 (PM1)
System Clock Control Register 0 (CM0)
System Clock Control Register 1 (CM1)
51
52
56
57
Address Match Interrupt Enable Register (AIER)
Protect Register (PRCR)
98
78
Main Clock Division Register (MCD)
Oscillation Stop Detection Register (CM2)
Watchdog Timer Start Register (WDTS)
Watchdog Timer Control Register (WDC)
58
59
104
Address Match Interrupt Register 0 (RMAD0)
98
Processor Mode Register 2 (PM2)
62
Address Match Interrupt Register 1 (RMAD1)
98
Address Match Interrupt Register 2 (RMAD2)
98
Address Match Interrupt Register 3 (RMAD3)
98
PLL Control Register 0 (PLC0)
PLL Control Register 1 (PLC1)
61
Address Match Interrupt Register 4 (RMAD4)
98
Address Match Interrupt Register 5 (RMAD5)
98
Address
Register
003016
003116
003216
003316
003416
003516
003616
003716
003816
003916 Address Match Interrupt Register 6 (RMAD6)
003A16
003B16
003C16
003D16 Address Match Interrupt Register 7 (RMAD7)
003E16
Page
98
98
003F16
004016
004116
004216
004316
004416
004516
004616
004716
004816
004916
004A16
004B16
004C16
004D16
004E16
004F16
005016
005116
005216
005316
005416
005516 Flash Memory Control Register 1 (FMR1)
005616
005716 Flash Memory Control Register 0 (FMR0)
005816
005916
005A16
005B16
005C16
005D16
005E16
005F16
375
374
Blank spaces are reserved. No access is allowed.
B-1
Quick Reference by Address
Address
006016
006116
006216
006316
006416
006516
006616
006716
006816
006916
006A16
006B16
006C16
006D16
006E16
006F16
007016
007116
007216
007316
007416
007516
007616
007716
007816
007916
007A16
007B16
007C16
007D16
007E16
007F16
008016
008116
008216
008316
008416
008516
008616
008716
008816
008916
008A16
008B16
008C16
008D16
008E16
008F16
Register
DMA0 Interrupt Control Register (DM0IC)
Timer B5 Interrupt Control Register (TB5IC)
DMA2 Interrupt Control Register (DM2IC)
UART2 Receive /ACK Interrupt Control Register (S2RIC)
Timer A0 Interrupt Control Register (TA0IC)
UART3 Receive /ACK Interrupt Control Register (S3RIC)
Timer A2 Interrupt Control Register (TA2IC)
UART4 Receive /ACK Interrupt Control Register (S4RIC)
Timer A4 Interrupt Control Register (TA4IC)
UART0 Bus Conflict Detect Interrupt Control Register (BCN0IC)/
UART3 Bus Conflict Detect Interrupt Control Register (BCN3IC)
UART0 Receive/ACK Interrupt Control Register (S0RIC)
A/D0 Conversion Interrupt Control Register (AD0IC)
UART1 Receive/ACK Interrupt Control Register (S1RIC)
Intelligent I/O Interrupt Control Register 0 (IIO0IC)/
CAN Interrupt 3 Control Register (CAN3IC)
Timer B1 Interrupt Control Register (TB1IC)
Intelligent I/O Interrupt Control Register 2 (IIO2IC)
Timer B3 Interrupt Control Register (TB3IC)
Intelligent I/O Interrupt Control Register 4 (IIO4IC)
INT5 Interrupt Control Register (INT5IC)
CAN Interrupt 8 Control Register (CAN8IC)
INT3 Interrupt Control Register (INT3IC)
Intelligent I/O Interrupt Control Register 8 (IIO8IC)
INT1 Interrupt Control Register (INT1IC)
Intelligent I/O Interrupt Control Register 10 (IIO10IC)/
CAN Interrupt 1 Control Register (CAN1IC)
87
88
87
88
87
88
87
CAN Interrupt 2 Control Register (CAN2IC)
87
DMA1 Interrupt Control Register (DM1IC)
UART2 Transmit /NACK Interrupt Control Register (S2TIC)
DMA3 Interrupt Control Register (DM3IC)
UART3 Transmit /NACK Interrupt Control Register (S3TIC)
Timer A1 Interrupt Control Register (TA1IC)
UART4 Transmit /NACK Interrupt Control Register (S4TIC)
Timer A3 Interrupt Control Register (TA3IC)
UART2 Bus Conflict Detect Interrupt Control Register (BCN2IC)
87
Blank spaces are reserved. No access is allowed.
B-2
Page
Address
Register
Page
009016 UART0 Transmit /NACK Interrupt Control Register (S0TIC)
UART1 Bus Conflict Detect Interrupt Control Register (BCN1IC)/
009116
UART4 Bus Conflict Detect Interrupt Control Register (BCN4IC)
009216 UART1 Transmit/NACK Interrupt Control Register (S1TIC)
009316 Key Input Interrupt Control Register (KUPIC)
009416 Timer B0 Interrupt Control Register (TB0IC)
87
Intelligent I/O Interrupt Control Register 1 (IIO1IC)/
009516
CAN Interrupt 4 Control Register (CAN4IC)
009616 Timer B2 Interrupt Control Register (TB2IC)
Intelligent I/O Interrupt Control Register 3 (IIO3IC)/
009716
CAN Interrupt 7 Control Register (CAN7IC)
009816 Timer B4 Interrupt Control Register (TB4IC)
009916 CAN Interrupt 5 Control Register (CAN5IC)
009A16 INT4 Interrupt Control Register (INT4IC)
88
009B16
009C16 INT2 Interrupt Control Register (INT2IC)
88
Intelligent I/O Interrupt Control Register 9 (IIO9IC)/
009D16
87
CAN Interrupt 0 Control Register (CAN0IC)
009E16 INT0 Interrupt Control Register (INT0IC)
88
009F16 Exit Priority Control Register (RLVL)
89
00A016 Interrupt Request Register 0 (IIO0IR)
00A116 Interrupt Request Register 1 (IIO1IR)
00A216 Interrupt Request Register 2 (IIO2IR)
101
00A316 Interrupt Request Register 3 (IIO3IR)
00A416 Interrupt Request Register 4 (IIO4IR)
00A516 Interrupt Request Register 5 (IIO5IR)
00A616 Interrupt Request Register 6 (IIO6IR)
00A716
00A816 Interrupt Request Register 8 (IIO8IR)
00A916 Interrupt Request Register 9 (IIO9IR)
101
00AA16 Interrupt Request Register 10 (IIO10IR)
00AB16 Interrupt Request Register 11 (IIO11IR)
00AC16
00AD16
00AE16
00AF16
00B016 Interrupt Enable Register 0 (IIO0IE)
00B116 Interrupt Enable Register 1 (IIO1IE)
00B216 Interrupt Enable Register 2 (IIO2IE)
102
00B316 Interrupt Enable Register 3 (IIO3IE)
00B416 Interrupt Enable Register 4 (IIO4IE)
00B516 Interrupt Enable Register 5 (IIO5IE)
00B616 Interrupt Enable Register 6 (IIO6IE)
00B716
00B816 Interrupt Enable Register 8 (IIO8IE)
00B916 Interrupt Enable Register 9 (IIO9IE)
102
00BA16 Interrupt Enable Register 10 (IIO10IE)
00BB16 Interrupt Enable Register 11 (IIO11IE)
00BC16
00BD16
00BE16
00BF16
Quick Reference by Address
Address
00C016
00C116
00C216
00C316
00C416
00C516
00C616
00C716
00C816
00C916
00CA16
00CB16
00CC16
00CD16
00CE16
00CF16
00D016
00D116
00D216
00D316
00D416
00D516
00D616
00D716
00D816
00D916
00DA16
00DB16
00DC16
00DD16
00DE16
00DF16
00E016
00E116
00E216
00E316
00E416
00E516
00E616
00E716
00E816
00E916
00EA16
00EB16
00EC16
00ED16
00EE16
00EF16
Register
Page
SI/O Receive Buffer Register0 (G0RB)
273
Transmit Buffer/Receive Data Register 0 (G0TB/G0DR)
279
Receive Input Register 0 (G0RI)
SI/O Communication Mode Register 0 (G0MR)
Transmit Output Register 0 (G0TO)
SI/O Communication Control Register 0 (G0CR)
272
274
272
273
Address
00F016
00F116
00F216
00F316
00F416
00F516
00F616
00F716
00F816
00F916
00FA16
00FB16
00FC16
00FD16
00FE16
00FF16
010016
010116
010216
010316
010416
010516
010616
010716
010816
010916
010A16
010B16
010C16
010D16
010E16
010F16
011016
011116
011216
011316
011416
011516
011616
011716
011816
011916
011A16
011B16
011C16
011D16
011E16
011F16
Register
Data Compare Register 00 (G0CMP0)
Data Compare Register 01 (G0CMP1)
Data Compare Register 02 (G0CMP2)
Data Compare Register 03 (G0CMP3)
Data Mask Register 00 (G0MSK0)
Data Mask Register 01 (G0MSK1)
Communication Clock Select Register (CCS)
Page
280
281
Receive CRC Code Register 0 (G0RCRC)
280
Tramsmit CRC Code Register 0 (G0TCRC)
SI/O Extended Mode Register 0 (G0EMR)
SI/O Extended Receive Control Register 0 (G0ERC)
SI/O Special Communication Interrupt Detect Register 0 (G0IRF)
SI/O Extended Transmit Control Register 0 (G0ETC)
Time Measurement Register 10 (G1TM0)/
Waveform Generating Register 10 (G1PO0)
Time Measurement Register 11 (G1TM1)/
Waveform Generating Register 11 (G1PO1)
Time Measurement Register 12 (G1TM2)/
Waveform Generating Register 12 (G1PO2)
Time Measurement Register 13 (G1TM3)/
Waveform Generating Register 13 (G1PO3)
Time Measurement Register 14 (G1TM4)/
Waveform Generating Register 14 (G1PO4)
Time Measurement Register 15 (G1TM5)/
Waveform Generating Register 16 (G1PO5)
Time Measurement Register 16 (G1TM6)/
Waveform Generating Register 16 (G1PO6)
Time Measurement Register 17 (G1TM7)/
Waveform Generating Register 17 (G1PO7)
Waveform Generating Control Register 10 (G1POCR0)
Waveform Generating Control Register 11 (G1POCR1)
Waveform Generating Control Register 12 (G1POCR2)
Waveform Generating Control Register 13 (G1POCR3)
Waveform Generating Control Register 14 (G1POCR4)
Waveform Generating Control Register 15 (G1POCR5)
Waveform Generating Control Register 16 (G1POCR6)
Waveform Generating Control Register 17 (G1POCR7)
Time Measurement Control Register 10 (G1TMCR0)
Time Measurement Control Register 11 (G1TMCR1)
Time Measurement Control Register 12 (G1TMCR2)
Time Measurement Control Register 13 (G1TMCR3)
Time Measurement Control Register 14 (G1TMCR4)
Time Measurement Control Register 15 (G1TMCR5)
Time Measurement Control Register 16 (G1TMCR6)
Time Measurement Control Register 17 (G1TMCR7)
275
272
278
276
251/
252
251
250
Blank spaces are reserved. No access is allowed.
B-3
Quick Reference by Address
Address
012016
012116
012216
012316
012416
012516
012616
012716
012816
012916
012A16
012B16
012C16
012D16
012E16
012F16
013016
013116
013216
013316
013416
013516
013616
013716
013816
013916
013A16
013B16
013C16
013D16
013E16
013F16
014016
014116
014216
014316
014416
014516
014616
014716
014816
014916
014A16
014B16
014C16
014D16
to
016F16
Register
Base Timer Register1 (G1BT)
248
Base Timer Control Register 10 (G1BCR0)
Base Timer Control Register 11 (G1BCR1)
Time Measurement Prescaler Register 16 (G1TPR6)
Time Measurement Prescaler Register 17 (G1TPR7)
Function Enable Register 1 (G1FE)
Function Select Register 1 (G1FS)
253
252
SI/O Receive Buffer Register 1 (G1RB)
273
Transmit Buffer/Receive Data Register 1 (G1TB/G1DR)
279
Receive Input Register 1 (G1RI)
SI/O Communication Mode Register 1 (G1MR)
Transmit Output Register 1 (G1TO)
SI/O Communication Control Register 1 (G1CR)
Data Compare Register 10 (G1CMP0)
Data Compare Register 11 (G1CMP1)
Data Compare Register 12 (G1CMP2)
Data Compare Register 13 (G1CMP3)
Data Mask Register 10 (G1MSK0)
Data Mask Register 11 (G1MSK1)
272
274
272
273
249
250
280
Receive CRC Code Register1 (G1RCRC)
280
Transmit CRC Code Register1 (G1TCRC)
SI/O Extended Mode Register 1 (G1EMR)
SI/O Extended Receive Control Register 1 (G1ERC)
SI/O Special Communication Interrupt Detect Register 1 (G1IRF)
SI/O Extended Transmit Control Register 1 (G1ETC)
Blank spaces are reserved. No access is allowed.
B-4
Page
275
277
279
276
Address
017016
017116
017216
017316
017416
017516
017616
017716
017816
017916
017A16
017B16
017C16
017D16
017F16
018016
018116
018216
018316
018416
018516
018616
018716
018816
018916
018A16
018B16
018C16
018D16
018E16
018F16
019016
019116
019216
019316
019416
019516
019616
019716
019816
019916
019A16
019B16
019C16
019D16
019E16
019F16
Register
CAN2 Slot Buffer Select Register (C2SBS)
CAN2 Control Register 1 (C2CTLR1)
CAN2 Sleep Control Register (C2SLPR)
Page
331
299
300
CAN2 Acceptance Filter Support Register (C2AFS)
336
Input Function Select Register (IPS)
Input Function Select Register A (IPSA)
363
364
CAN2 Message Slot Buffer 0 Standard ID0 (C2SLOT0_0)
CAN2 Message Slot Buffer 0 Standard ID1 (C2SLOT0_1)
CAN2 Message Slot Buffer 0 Extended ID0 (C2SLOT0_2)
CAN2 Message Slot Buffer 0 Extended ID1 (C2SLOT0_3)
CAN2 Message Slot Buffer 0 Extended ID2 (C2SLOT0_4)
CAN2 Message Slot Buffer 0 Data Length Code (C2SLOT0_5)
CAN2 Message Slot Buffer 0 Data 0 (C2SLOT0_6)
CAN2 Message Slot Buffer 0 Data 1 (C2SLOT0_7)
CAN2 Message Slot Buffer 0 Data 2 (C2SLOT0_8)
CAN2 Message Slot Buffer 0 Data 3 (C2SLOT0_9)
CAN2 Message Slot Buffer 0 Data 4 (C2SLOT0_10)
CAN2 Message Slot Buffer 0 Data 5 (C2SLOT0_11)
CAN2 Message Slot Buffer 0 Data 6 (C2SLOT0_12)
CAN2 Message Slot Buffer 0 Data 7 (C2SLOT0_13)
CAN2 Message Slot Buffer 0 Time Stamp High-Order (C2SLOT0_14)
CAN2 Message Slot Buffer 0 Time Stamp Low-Order (C2SLOT0_15)
CAN2 Message Slot Buffer 1 Standard ID0 (C2SLOT1_0)
CAN2 Message Slot Buffer 1 Standard ID1 (C2SLOT1_1)
CAN2 Message Slot Buffer 1 Extended ID0 (C2SLOT1_2)
CAN2 Message Slot Buffer 1 Extended ID1 (C2SLOT1_3)
CAN2 Message Slot Buffer 1 Extended ID2 (C2SLOT1_4)
CAN2 Message Slot Buffer 1 Data Length Code (C2SLOT1_5)
CAN2 Message Slot Buffer 1 Data 0 (C2SLOT1_6)
CAN2 Message Slot Buffer 1 Data 1 (C2SLOT1_7)
CAN2 Message Slot Buffer 1 Data 2 (C2SLOT1_8)
CAN2 Message Slot Buffer 1 Data 3 (C2SLOT1_9)
CAN2 Message Slot Buffer 1 Data 4 (C2SLOT1_10)
CAN2 Message Slot Buffer 1 Data 5 (C2SLOT1_11)
CAN2 Message Slot Buffer 1 Data 6 (C2SLOT1_12)
CAN2 Message Slot Buffer 1 Data 7 (C2SLOT1_13)
CAN2 Message Slot Buffer 1 Time Stamp High-Order (C2SLOT1_14)
CAN2 Message Slot Buffer 1 Time Stamp Low-Order (C2SLOT1_15)
332
333
334
335
332
333
334
335
Quick Reference by Address
Address
01A016
01A116
01A216
01A316
01A416
01A516
01A616
01A716
01A816
01A916
01AA16
01AB16
01AC16
01AD16
01AE16
01AF16
01B016
01B116
01B216
01B316
01B416
01B516
01B616
01B716
01B816
01B916
01BA16
01BB16
01BC16
01BD16
01BE16
01BF16
01C016
01C116
01C216
01C316
01C416
01C516
01C616
01C716
01C816
01C916
01CA16
01CB16
01CC16
01CD16
01CE16
01CF16
Page
Address
CAN2 Control Register0 (C2CTLR0)
296
01D016
CAN2 Status Register (C2STR)
301
01D116
CAN2 Extended ID Register (C2IDR)
304
01D216
CAN2 Configuration Register (C2CONR)
305
01D316
CAN2 Time Stamp Register (C2TSR)
308
01D416
CAN2 Transmit Error Count Register (C2TEC)
CAN2 Receive Error Count Register (C2REC)
309
333
CAN2 Slot Interrupt Status Register (C2SISTR)
310
01D516
01D616
01D716
Register
01D816
01D916
CAN2 Slot Interrupt Mask Register (C2SIMKR)
312
01DA16
CAN2 Error Interrupt Mask Register (C2EIMKR)
CAN2 Error Interrupt Status Register (C2EISTR)
CAN2 Error Cause Register (C2EFR)
CAN2 Baud Rate Prescaler (C2BRP)
313
314
315
307
CAN2 Mode Register (C2MDR)
316
CAN2 Single Shot Control Register (C2SSCTLR)
318
CAN2 Single Shot Status Register (C2SSSTR)
319
CAN2 Global Mask Register Standard ID0 (C2GMR0)
CAN2 Global Mask Register Standard ID1 (C2GMR1)
CAN2 Global Mask Register Extended ID0 (C2GMR2)
CAN2 Global Mask Register Extended ID1 (C2GMR3)
CAN2 Global Mask Register Extended ID2 (C2GMR4)
320
321
322
323
324
01DB16
01DC16
01DD16
01DE16
01DF16
01E016
01E116
01E216
01E316
01E416
01E516
01E616
01E716
01E816
01E916
01EA16
01EB16
01EC16
01ED16
01EE16
01EF16
Register
Page
CAN2 Message Slot 0 Control Register (C2MCTL0)/ 327/
CAN2 Local Mask Register A Standard ID0 (C2LMAR0)
320
CAN2 Message Slot 1 Control Register (C2MCTL1)/ 327/
CAN2Local Mask Register A Standard ID1 (C2LMAR1)
321
CAN2 Message Slot 2 Control Register (C2MCTL2)/
327/
CAN2 Local Mask Register A Extended ID0 (C2LMAR2) 322
CAN2 Message Slot 3 Control Register (C2MCTL3)/ 327/
CAN2 Local Mask Register A Extended ID1 (C2LMAR3) 323
CAN2 Message Slot 4 Control Register (C2MCTL4)/ 327/
CAN2 Local Mask Register A Extended ID2 (C2LMAR4) 324
CAN2 Message Slot 5 Control Register (C2MCTL5)
CAN2 Message Sot 6 Control Register (C2MCTL6) 327
CAN2 Message Slot 7 Control Register (C2MCTL7)
CAN2 Message Slot 8 Control register (C2MCTL8)/ 327/
CAN2 Local Mask Register B Standard ID0 (C2LMBR0) 320
CAN2 Message Slot 9 Control register (C2MCTL9)/ 327/
CAN2 Local Mask Register B Standard ID1 (C2LMBR1) 321
CAN2 Message Slot 10 Control register (C2MCTL10)/ 327/
CAN2 Local Mask Register B Standard ID2 (C2LMBR2) 322
CAN2 Message Slot 11 Control register (C2MCTL11)/ 327/
CAN2 Local Mask Register B Standard ID3 (C2LMBR3) 323
CAN2 Message Slot 12 Control register (C2MCTL12)/ 327/
CAN2 Local Mask Register B Standard ID4 (C2LMBR4) 324
CAN2 Message Slot 13 Control Register (C2MCTL13)
CAN2 Message Sot 14 Control Register (C2MCTL14) 327
CAN2 Message Slot 15 Control Register (C2MCTL15)
CAN0 Message Slot Buffer 0 Standard ID0 (C0SLOT0_0)
332
CAN0 Message Slot Buffer 0 Standard ID1 (C0SLOT0_1)
CAN0 Message Slot Buffer 0 Extended ID0 (C0SLOT0_2)
333
CAN0 Message Slot Buffer 0 Extended ID1 (C0SLOT0_3)
CAN0 Message Slot Buffer 0 Extended ID2 (C0SLOT0_4)
334
CAN0 Message Slot Buffer 0 Data Length Code (C0SLOT0_5)
CAN0 Message Slot Buffer 0 Data 0 (C0SLOT0_6)
CAN0 Message Slot Buffer 0 Data 1 (C0SLOT0_7)
CAN0 Message Slot Buffer 0 Data 2 (C0SLOT0_8)
CAN0 Message Slot Buffer 0 Data 3 (C0SLOT0_9)
CAN0 Message Slot Buffer 0 Data 4 (C0SLOT0_10)
335
CAN0 Message Slot Buffer 0 Data 5 (C0SLOT0_11)
CAN0 Message Slot Buffer 0 Data 6 (C0SLOT0_12)
CAN0 Message Slot Buffer 0 Data 7 (C0SLOT0_13)
CAN0 Message Slot Buffer 0 Time Stamp High-Order (C0SLOT0_14)
CAN0 Message Slot Buffer 0 Time Stamp Low-Order (C0SLOT0_15)
Blank spaces are reserved. No access is allowed.
B-5
Quick Reference by Address
Address
01F016
01F116
01F216
01F316
01F416
01F516
01F616
01F716
01F816
01F916
01FA16
01FB16
01FC16
01FD16
01FE16
01FF16
020016
020116
020216
020316
020416
020516
020616
020716
020816
020916
020A16
020B16
020C16
020D16
020E16
020F16
021016
021116
021216
021316
021416
021516
021616
021716
021816
021916
021A16
021B16
021C16
021D16
021E16
021F16
Register
Page
CAN0 Message Slot Buffer 1 Standard ID0 (C0SLOT1_0)
332
CAN0 Message Slot Buffer 1 Standard ID1 (C0SLOT1_1)
CAN0 Message Slot Buffer 1 Extended ID0 (C0SLOT1_2)
333
CAN0 Message Slot Buffer 1 Extended ID1 (C0SLOT1_3)
CAN0 Message Slot Buffer 1 Extended ID2 (C0SLOT1_4)
334
CAN0 Message Slot Buffer 1 Data Length Code (C0SLOT1_5)
CAN0 Message Slot Buffer 1 Data 0 (C0SLOT1_6)
CAN0 Message Slot Buffer 1 Data 1 (C0SLOT1_7)
CAN0 Message Slot Buffer 1 Data 2 (C0SLOT1_8)
CAN0 Message Slot Buffer 1 Data 3 (C0SLOT1_9)
CAN0 Message Slot Buffer 1 Data 4 (C0SLOT1_10)
335
CAN0 Message Slot Buffer 1 Data 5 (C0SLOT1_11)
CAN0 Message Slot Buffer 1 Data 6 (C0SLOT1_12)
CAN0 Message Slot Buffer 1 Data 7 (C0SLOT1_13)
CAN0 Message Slot Buffer 1 Time Stamp High-Order (C0SLOT1_14)
CAN0 Message Slot Buffer 1 Time Stamp Low-Order (C0SLOT1_15)
Address
022016
022116
022216
022316
022416
022516
022616
022716
022816
022916
022A16
022B16
022C16
022D16
022E16
022F16
CAN0 Control Register0 (C0CTLR0)
296
023016
CAN0 Status Register (C0STR)
301
023116
CAN0 Extended ID Register (C0IDR)
304
023216
CAN0 Configuration Register (C0CONR)
305
023316
CAN0 Time Stamp Register (C0TSR)
308
CAN0 Transmit Error Count Register (C0TEC)
CAN0 Receive Error Count Register (C0REC)
309
CAN0 Slot Interrupt Status Register (C0SISTR)
310
023516
023616
023716
023816
023916
CAN0 Slot Interrupt Mask Register (C0SIMKR)
312
023A16
CAN0 Error Interrupt Mask Register (C0EIMKR)
CAN0 Error Interrupt Status Register (C0EISTR)
CAN0 Error Cause Register (C0EFR)
CAN0 Baud Rate Prescaler (C0BRP)
313
314
315
307
CAN0 Mode Register (C0MDR)
316
Blank spaces are reserved. No access is allowed.
B-6
023416
023B16
023C16
023D16
023E16
023F16
Register
Page
CAN0 Single Shot Control Register (C0SSCTLR)
318
CAN0 Single Shot Status Register (C0SSSTR)
319
CAN0 Global Mask Register Standard ID0 (C0GMR0)
CAN0 Global Mask Register Standard ID1 (C0GMR1)
CAN0 Global Mask Register Extended ID0 (C0GMR2)
CAN0 Global Mask Register Extended ID1 (C0GMR3)
CAN0 Global Mask Register Extended ID2 (C0GMR4)
320
321
322
323
324
CAN0 Message Slot 0 Control Register (C0MCTL0)/
CAN0 Local Mask Register A Standard ID0 (C0LMAR0)
CAN0 Message Slot 1 Control Register (C0MCTL1)/
CAN0Local Mask Register A Standard ID1 (C0LMAR1)
CAN0 Message Slot 2 Control Register (C0MCTL2)/
CAN0 Local Mask Register A Extended ID0 (C0LMAR2)
CAN0 Message Slot 3 Control Register (C0MCTL3)/
CAN0 Local Mask Register A Extended ID1 (C0LMAR3)
CAN0 Message Slot 4 Control Register (C0MCTL4)/
CAN0 Local Mask Register A Extended ID2 (C0LMAR4)
CAN0 Message Slot 5 Control Register (C0MCTL5)
CAN0 Message Sot 6 Control Register (C0MCTL6)
CAN0 Message Slot 7 Control Register (C0MCTL7)
CAN0 Message Slot 8 Control register (C0MCTL8)/
CAN0 Local Mask Register B Standard ID0 (C0LMBR0)
CAN0 Message Slot 9 Control Register (C0MCTL9)/
CAN0 Local Mask Register B Standard ID1 (C0LMBR1)
CAN0 Message Slot 10 Control Register (C0MCTL10)/
CAN0 Local Mask Register B Extended ID0 (C0LMBR2)
CAN0 Message Slot 11 Control Register (C0MCTL11)/
CAN0 Local Mask Register B Extended ID1 (C0LMBR3)
CAN0 Message Slot 12 Control Register (C0MCTL12)/
CAN0 Local Mask Register B Extended ID2 (C0LMBR4)
CAN0 Message Slot 13 Control Register (C0MCTL13)
CAN0 Message Slot 14 Control Register (C0MCTL14)
CAN0 Message Slot 15 Control Register(C0MCTL15)
327/
320
327/
321
327/
322
327/
323
327/
324
327
327/
320
327/
321
327/
322
327/
323
327/
324
327
Quick Reference by Address
Address
024016
024116
024216
024316
024416
024516
024616
024716
024816
024916
024A16
024B16
024C16
024D16
024E16
024F16
025016
025116
025216
025316
025416
025516
025616
025716
025816
025916
025A16
025B16
025C16
025D16
025E16
025F16
026016
026116
026216
026316
026416
026516
026616
026716
026816
026916
026A16
026B16
026C16
026D16
026E16
026F16
Register
CAN0 Slot Buffer Select Register (C0SBS)
CAN0 Control Register 1 (C0CTLR1)
CAN0 Sleep Control Register (C0SLPR)
Page
331
299
300
CAN0 Acceptance Filter Support Register (C0AFS)
336
CAN1 Slot Buffer Select Register (C1SBS)
CAN1 Control Register 1 (C1CTLR1)
CAN1 Sleep Control Register (C1SLPR)
331
299
300
CAN1 Acceptance Filter Support Register (C1AFS)
336
CAN1 Message Slot Buffer 0 Standard ID0 (C1SLOT0_0)
CAN1 Message Slot Buffer 0 Standard ID1 (C1SLOT0_1)
CAN1 Message Slot Buffer 0 Extended ID0 (C1SLOT0_2)
CAN1 Message Slot Buffer 0 Extended ID1 (C1SLOT0_3)
CAN1 Message Slot Buffer 0 Extended ID2 (C1SLOT0_4)
CAN1 Message Slot Buffer 0 Data Length Code (C1SLOT0_5)
CAN1 Message Slot Buffer 0 Data 0 (C1SLOT0_6)
CAN1 Message Slot Buffer 0 Data 1 (C1SLOT0_7)
CAN1 Message Slot Buffer 0 Data 2 (C1SLOT0_8)
CAN1 Message Slot Buffer 0 Data 3 (C1SLOT0_9)
CAN1 Message Slot Buffer 0 Data 4 (C1SLOT0_10)
CAN1 Message Slot Buffer 0 Data 5 (C1SLOT0_11)
CAN1 Message Slot Buffer 0 Data 6 (C1SLOT0_12)
CAN1 message Slot Buffer 0 Data 7 (C1SLOT0_13)
CAN1 Message Slot Buffer 0 Time Stamp High-Order (C1SLOT0_14)
CAN1 Message Slot Buffer 0 Time Stamp Low-Order (C1SLOT0_15)
332
333
334
335
Address
027016
027116
027216
027316
027416
027516
027616
027716
027816
027916
027A16
027B16
027C16
027D16
027E16
027F16
028016
028116
028216
028316
028416
028516
028616
028716
028816
028916
028A16
028B16
028C16
028D16
028E16
028F16
029016
029116
029216
029316
029416
029516
029616
029716
029816
029916
029A16
029B16
029C16
029D16
029E16
029F16
Register
Page
CAN1 Message Slot Buffer 1 Standard ID0 (C1SLOT1_0)
332
CAN1 Message Slot Buffer 1 Standard ID1 (C1SLOT1_1)
CAN1 Message Slot Buffer 1 Extended ID0 (C1SLOT1_2)
333
CAN1 Message Slot Buffer 1 Extended ID1 (C1SLOT1_3)
CAN1 Message Slot Buffer 1 Extended ID2 (C1SLOT1_4)
334
CAN1 Message Slot Buffer 1 Data Length Code (C1SLOT1_5)
CAN1 Message Slot Buffer 1 Data 0 (C1SLOT1_6)
CAN1 Message Slot Buffer 1 Data 1 (C1SLOT1_7)
CAN1 Message Slot Buffer 1 Data 2 (C1SLOT1_8)
CAN1 Message Slot Buffer 1 Data 3 (C1SLOT1_9)
CAN1 Message Slot Buffer 1 Data 4 (C1SLOT1_10)
335
CAN1 Message Slot Buffer 1 Data 5 (C1SLOT1_11)
CAN1 Message Slot Buffer 1 Data 6 (C1SLOT1_12)
CAN1 Message Slot Buffer 1 Data 7 (C1SLOT1_13)
CAN1 Message Slot Buffer 1 Time Stamp High-Order (C1SLOT1_14)
CAN1 Message Slot Buffer 1 Time Stamp Low-Order (C1SLOT1_15)
CAN1 Control Register0 (C1CTLR0)
296
CAN1 Status Register (C1STR)
301
CAN1 Extended ID Register (C1IDR)
304
CAN1 Configuration Register (C1CONR)
305
CAN1 Time Stamp Register (C1TSR)
308
CAN1 Transmit Error Count Register (C1TEC)
CAN1 Receive Error Count Register (C1REC)
309
CAN1 Slot Interrupt Control Register (C1SISTR)
310
CAN1 Slot Interrupt Mask Register (C1SIMKR)
312
CAN1 Error Interrupt Mask Register (C1EIMKR)
CAN1 Error Interrupt Status Register (C1EISTR)
CAN1 Error Factor Register (C1EFR)
CAN1 Baud Rate Prescaler (C1BRP)
313
314
315
307
CAN1 Mode Register (C1MDR)
316
Blank spaces are reserved. No access is allowed.
B-7
Quick Reference by Address
Address
02A016
02A116
02A216
02A316
02A416
02A516
02A616
02A716
02A816
02A916
02AA16
02AB16
02AC16
02AD16
02AE16
02AF16
02B016
02B116
02B216
02B316
02B416
02B516
02B616
02B716
02B816
02B916
02BA16
02BB16
02BC16
02BD16
02BE16
02BF16
Register
Page
CAN1 Single Shot Control Register (C1SSCTLR)
318
CAN1 Single Shot Status Register (C1SSSTR)
CAN1 Global Mask Register Standard ID0 (C1GMR0)
CAN1 Global Mask Register Standard ID1 (C1GMR1)
CAN1 Global Mask Register Extended ID0 (C1GMR2)
CAN1 Global Mask Register Extended ID1 (C1GMR3)
CAN1 Global Mask Register Extended ID2 (C1GMR4)
CAN1 Message Slot 0 Control Register (C1MCTL0)/
CAN1 Local Mask Register A Standard ID0 (C1LMAR0)
CAN1 Message Slot 1 Control Register (C1MCTL1)/
CAN1 Local Mask Register A Standard ID1 (C1LMAR1)
CAN1 Message Slot 2 Control Register (C1MCTL2)/
CAN1 Local Mask Register A Extended ID0 (C1LMAR2)
CAN1 Message Slot 3 Control Register (C1MCTL3)/
CAN1 Local Mask Register A Extended ID1 (C1LMAR3)
CAN1 Message Slot 4 Control Register (C1MCTL4)/
CAN1 Local Mask Register A Extended ID2 (C1LMAR4)
CAN1 Message Slot 5 Control Register (C1MCTL5)
CAN1 Message Slot 6 Control Register (C1MCTL6)
CAN1 Message Slot 7 Control Register (C1MCTL7)
CAN1 Message Slot 8 Control Register (C1MCTL8)/
CAN1 Local Mask Register B Standard ID0 (C1LMBR0)
CAN1 Message Slot 9 Control Register (C1MCTL9)/
CAN1 Local Mask Register B Standard ID1 (C1LMBR1)
CAN1 Message Slot 10 Control Register (C1MCTL10)/
CAN1 Local Mask Register B Extended ID0 (C1LMBR2)
CAN1 Message Slot 11 Control Register (C1MCTL11)/
CAN1 Local Mask Register B Extended ID1 (C1LMBR3)
CAN1 Message Slot 12 Control Register (C1MCTL12)/
CAN1 Local Mask Register B Extended ID2 (C1LMBR4)
CAN1 Message Slot 13 Control Register (C1MCTL13)
CAN1 Message Slot 14 Control Register (C1MCTL14)
CAN1 Message Slot 15 Control Register (C1MCTL15)
Blank spaces are reserved. No access is allowed.
B-8
319
320
321
322
323
324
327/
320
327/
321
327/
322
327/
323
327/
324
327
327/
320
353/
321
327/
322
327/
323
327/
324
327
Address
02C016
02C116
02C216
02C316
02C416
02C516
02C616
02C716
02C816
02C916
02CA16
02CB16
02CC16
02CD16
02CE16
02CF16
02D016
02D116
02D216
02D316
02D416
02D516
02D616
02D716
02D816
02D916
02DA16
02DB16
02DC16
02DD16
02DE16
02DF16
Register
Page
X0 Register Y0 Register (X0R,Y0R)
X1 Register Y1 Register (X1R,Y1R)
X2 Register Y2 Register (X2R,Y2R)
X3 Register Y3 Register (X3R,Y3R)
X4 Register Y4 Register (X4R,Y4R)
X5 Register Y5 Register (X5R,Y5R)
X6 Register Y6 Register (X6R,Y6R)
X7 Register Y7 Register (X7R,Y7R)
242
X8 Register Y8 Register (X8R,Y8R)
X9 Register Y9 Register (X9R,Y9R)
X10 Register Y10 Register (X10R,Y10R)
X11 Register Y11 Register (X11R,Y11R)
X12 Register Y12 Register (X12R,Y12R)
X13 Register Y13 Register (X13R,Y13R)
X14 Register Y14 Register (X14R,Y14R)
X15 Register Y15 Register (X15R,Y15R)
Quick Reference by Address
Address
02E016
02E116
02E216
02E316
02E416
02E516
02E616
02E716
02E816
02E916
02EA16
02EB16
02EC16
02ED16
02EE16
02EF16
02F016
02F116
02F216
02F316
02F416
02F516
02F616
02F716
02F816
02F916
02FA16
02FB16
02FC16
02FD16
02FE16
02FF16
030016
030116
030216
030316
030416
030516
030616
030716
030816
030916
030A16
030B16
030C16
030D16
030E16
030F16
Register
X/Y Control Register (XYC)
UART1 Special Mode Register 4 (U1SMR4)
UART1 Special Mode Register 3 (U1SMR3)
UART1 Special Mode Register 2 (U1SMR2)
UART1 Special Mode Register (U1SMR)
UART1 Transmit/Receive Mode Register (U1MR)
UART1 Bit Rate Register (U1BRG)
Page
242
173
172
171
170
168
UART1 Transmit Buffer Register (U1TB)
167
UART1 Transmit/Receive Control Register 0 (U1C0)
UART1 Transmit/Receive Control Register 1 (U1C1)
169
170
UART1 Receive Buffer Register (U1RB)
167
UART4 Special Mode Register 4 (U4SMR4)
UART4 Special Mode Register 3 (U4SMR3)
UART4 Special Mode Register 2 (U4SMR2)
UART4 Special Mode Register (U4SMR)
UART4 Transmit/Receive Mode Register (U4MR)
UART4 Bit Rate Register (U4BRG)
173
172
171
170
168
UART4 Transmit Buffer Register (U4TB)
167
UART4 Transmit/Receive Control Register 0 (U4C0)
UART4 Transmit/Receive Control Register 1 (U4C1)
169
170
UART4 Receive Buffer Register (U4RB)
167
Timer B3,B4,B5 Count Start Flag (TBSR)
147
Timer A1-1 Register (TA11)
Timer A2-1 Register (TA21)
160
Timer A4-1 Register (TA41)
Three-Phase PWM Control Register 0 (INVC0)
Three-Phase PWM Control Register 1 (INVC1)
Three-Phase Output Buffer Register 0 (IDB0)
Three-Phase Output Buffer Register 1 (IDB1)
Dead Time Timer (DTT)
Timer B2 Interrupt Generating Frequency Set Counter (ICTB2)
157
158
159
160
Address
031016
031116
031216
031316
031416
031516
031616
031716
031816
031916
031A16
031B16
031C16
031D16
031E16
031F16
032016
032116
032216
032316
032416
032516
032616
032716
032816
032916
032A16
032B16
032C16
032D16
032E16
032F16
033016
033116
033216
033316
033416
033516
033616
033716
033816
033916
033A16
033B16
033C16
033D16
033E16
033F16
Register
Page
Timer B3 Register (TB3)
Timer B4 Register (TB4)
145
Timer B5 Register (TB5)
Timer B3 Mode Register (TB3MR)
Timer B4 Mode Register (TB4MR)
Timer B5 Mode Register (TB5MR)
146
External Interrupt Request Source Select Register (IFSR)
96
UART3 Special Mode Register 4 (U3SMR4)
UART3 Special Mode Register 3 (U3SMR3)
UART3 Special Mode Register 2 (U3SMR2)
UART3 Special Mode Register (U3SMR)
UART3 Transmit/Receive Mode Register (U3MR)
UART3 Bit Rate Register (U3BRG)
173
172
171
170
168
UART3 Transmit Buffer Register (U3TB)
167
UART3 Transmit/Receive Control Register 0 (U3C0)
UART3 Transmit/Receive Control Register 1 (U3C1)
169
170
UART3 Receive Buffer Register (U3RB)
167
UART2 Special Mode Register 4 (U2SMR4)
UART2 Special Mode Register 3 (U2SMR3)
UART2 Special Mode Register 2 (U2SMR2)
UART2 Special Mode Register (U2SMR)
UART2 Transmit/Receive Mode Register (U2MR)
UART2 Bit Rate Register (U2BRG)
173
172
171
170
168
UART2 Transmit Buffer Register (U2TB)
167
UART2 Transmit/Receive Control Register 0 (U2C0)
UART2 Transmit/Receive Control Register 1 (U2C1)
169
170
UART2 Receive Buffer Register (U2RB)
167
Blank spaces are reserved. No access is allowed.
B-9
Quick Reference by Address
Address
034016
034116
034216
034316
034416
034516
034616
034716
034816
034916
034A16
034B16
034C16
034D16
034E16
034F16
035016
035116
035216
035316
035416
035516
035616
035716
035816
035916
035A16
035B16
035C16
035D16
035E16
035F16
036016
036116
036216
036316
036416
036516
Register
Count Start Flag (TABSR)
Clock Prescaler Reset Flag (CPSRF)
One-Shot Start Flag (ONSF)
Trigger Select Register (TRGSR)
Up/Down Flag (UDF)
UART0 Special Mode Register 4 (U0SMR4)
UART0 Special Mode Register 3 (U0SMR3)
173
172
036616
036716
036816
036916
036A16
036B16
036C16
036D16
036E16
036F16
UART0 Special Mode Register 2 (U0SMR2)
UART0 Special Mode Register (U0SMR)
UART0 Transmit/Receive Mode Register (U0MR)
UART0 Bit Rate Register (U0BRG)
171
170
Timer A0 Register (TA0)
Timer A1 Register (TA1)
Timer A2 Register (TA2)
129
Timer A3 Register (TA3)
Timer A4 Register (TA4)
Timer B0 Register (TB0)
Timer B1 Register (TB1)
145
Timer B2 Register (TB2)
Timer A0 Mode Register (TA0MR)
Timer A1 Mode Register (TA1MR)
Timer A2 Mode Register (TA2MR)
Timer A3 Mode Register (TA3MR)
Timer A4 Mode Register (TA4MR)
Timer B0 Mode Register (TB0MR)
Timer B1 Mode Register (TB1MR)
Timer B2 Mode Register (TB2MR)
Timer B2 Special Mode Register (TB2SC)
Count Source Prescaler Register (TCSPR)
130
146
160
60
168
UART0 Transmit Buffer Register (U0TB)
167
UART0 Transmit/Receive Control Register 0 (U0C0)
UART0 Transmit/Receive Control Register 1 (U0C1)
169
170
UART0 Receive Buffer Register (U0RB)
167
Blank spaces are reserved. No access is allowed.
B-10
Page
130
60
131
132
131
Address
037016
037116
037216
037316
037416
037516
037616
037716
037816
037916
037A16
037B16
037C16
037D16
037E16
037F16
038016
038116
038216
038316
038416
038516
038616
038716
038816
038916
038A16
038B16
038C16
038D16
038E16
038F16
039016
039116
039216
039316
039416
039516
039616
039716
039816
039916
039A16
039B16
039C16
039D16
039E16
039F16
Register
Page
DMA0 Request Source Select Register (DM0SL)
DMA1 Request Source Select Register (DM1SL)
DMA2 Request Source Select Register (DM2SL)
DMA3 Request Source Select Register (DM3SL)
109
CRC Data Register (CRCD)
240
CRC Input Register (CRCIN)
A/D0 Register0 (AD00)
A/D0 Register1 (AD01)
A/D0 Register2 (AD02)
A/D0 Register3 (AD03)
225
A/D0 Register4 (AD04)
A/D0 Register5 (AD05)
A/D0 Register6 (AD06)
A/D0 Register7 (AD07)
A/D0 Control Register 4 (AD0CON4)
225
A/D0 Control Register 2 (AD0CON2)
A/D0 Control Register 3 (AD0CON3)
224
223
A/D0 Control Register 0 (AD0CON0)
A/D0 Control Register 1 (AD0CON1)
D/A Register 0 (DA0)
222
221
239
D/A Register 1 (DA1)
239
D/A Control Register (DACON)
239
Quick Reference by Address
Address
03A016
03A116
03A216
03A316
03A416
03A516
03A616
03A716
03A816
03A916
03AA16
03AB16
03AC16
03AD16
03AE16
03AF16
03B016
Register
Function Select Register A8 (PS8)
Function Select Register A9 (PS9)
03B116
03B216
03B316
03B416
03B516
03B616
03B716
03B816
03B916
03BA16
03BB16
03BC16
03BD16
03BE16
03BF16
03C016
03C116
03C216
03C316
03C416
03C516
03C616
03C716
03C816
03C916
03CA16
03CB16
03CC16
03CD16
03CE16
03CF16
Function Select Register A1 (PS1)
Function Select Register B0 (PSL0)
Function Select Register B1 (PSL1)
Function Select Register A2 (PS2)
Function Select Register A3 (PS3)
Function Select Register B2 (PSL2)
Function Select Register B3 (PSL3)
Function Select Register D1 (PSD1)
Page
355
356
360
Function Select Register C2 (PSC2)
Function Select Register C3 (PSC3)
359
360
Function Select Register C (PSC)
Function Select Register A0 (PS0)
359
Function Select Register A5 (PS5)
Port P6 Register (P6)
Port P7 Register (P7)
Port P6 Direction Register (PD6)
Port P7 Direction Register (PD7)
Port P8 Register (P8)
Port P9 Register (P9)
Port P8 Direction Register (PD8)
Port P9 Direction Register (PD9)
Port P10 Register (P10)
Port P11 Register (P11)
Port P10 Direction Register (PD10)
Port P11 Direction Register(PD11)
Port P12 Register (P12)
Port P13 Register (P13)
Port P12 Direction Register (PD12)
Port P13 Direction Register (PD13)
353
357
354
358
355
352
351
352
351
352
351
352
351
Address
03D016
03D116
03D216
03D316
03D416
03D516
03D616
03D716
03D816
03D916
03DA16
03DB16
03DC16
03DD16
03DE16
03DF16
03E016
Register
Port P14 Register (P14)
Port P15 Register (P15)
Port P14 Direction Register (PD14)
Port P15 Direction Register (PD15)
Page
Pull-Up Control Register 2 (PUR2)
Pull-Up Control Register 3 (PUR3)
Pull-Up Control Register 4 (PUR4)
361
03E116
03E216
03E316
03E416
03E516
03E616
03E716
03E816
03E916
03EA16
03EB16
03EC16
03ED16
03EE16
03EF16
03F016
03F116
03F216
03F316
03F416
03F516
03F616
03F716
03F816
03F916
03FA16
03FB16
03FC16
03FD16
03FE16
03FF16
Port P1 Register (P1)
Port P0 Direction Register (PD0)
Port P1 Direction Register (PD1)
Port P2 Register (P2)
Port P3 Register (P3)
Port P2 Direction Register (PD2)
Port P3 Direction Register (PD3)
Port P4 Register (P4)
Port P5 Register (P5)
Port P4 Direction Register (PD4)
Port P5 Direction Register (PD5)
Port P0 Register (P0)
352
351
362
352
351
352
351
352
351
Pull-up Control Register 0 (PUR0)
Pull-up Control Register 1 (PUR1)
361
Port Control Register (PCR)
363
Blank spaces are reserved. No access is allowed.
B-11
M32C/88 Group (M32C/88T)
SINGLE-CHIP 16/32-BIT CMOS MICROCOMPUTER
1. Overview
The M32C/88 Group (M32C/88T) microcomputer is a single-chip control unit that utilizes high-performance
silicon gate CMOS technology with the M32C/80 Series CPU core. The M32C/88 Group (M32C/88T) is
available in 144-pin and 100-pin plastic molded LQFP packages.
With a 16-Mbyte address space, this microcomputer combines advanced instruction manipulation capabilities to process complex instructions by less bytes and execute instructions at higher speed.
It includes a multiplier and DMAC adequate for office automation, communication devices and industrial
equipments, and other high-speed processing applications.
1.1 Applications
Automobiles, audio, cameras, office equipment, communications equipment, portable equipment, etc.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 1
of 435
1. Overview
M32C/88 Group (M32C/88T)
1.2 Performance Overview
Tables 1.1 and 1.2 list performance overview of the M32C/88 Group (M32C/88T).
Table 1.1 M32C/88 Group (M32C/88T) Performance (144-Pin Package)
Characteristic
Basic Instructions
Minimum Instruction Execution Time
Operating Mode
Address Space
Memory Capacity
Peripheral I/O Port
Function Multifunction Timer
CPU
Intelligent I/O
Serial I/O
CAN Module
A/D Converter
D/A Converter
DMAC
DMAC II
CRC Calculation Circuit
X/Y Converter
Watchdog Timer
Interrupt
Clock Generation Circuit
Oscillation Stop Detect Function
Cold Start-up/Warm Start-up
Determine Function
Electrical Supply Voltage
Charact- Power Consumption
eristics
Flash
Program/Erase Supply Voltage
Memory Program and Erase Endurance
Operating Ambient Temperature
Package
Performance
108 instructions
31.3 ns (f(BCLK)=32 MHz, VCC=4.2 V to 5.5 V)
Single-chip mode
16 Mbytes
See Table 1.3
123 I/O pins and 1 input pin
Timer A: 16 bits x 5 channels, Timer B: 16 bits x 6 channels
Three-phase motor control circuit
Time measurement function or Waveform generating function:
16 bits x 8 channels
Communication function (Clock synchronous serial I/O, Clock asynchronous serial I/O, HDLC data processing)
5 Channels
Clock synchronous serial I/O, Clock asynchronous serial I/O,
IEBus(1), I2C bus(2)
3 channels Supporting CAN 2.0B specification
10-bit A/D converter: 1 circuit, 34 channels
8 bits x 2 channels
4 channels
Can be activated by all peripheral function interrupt sources
Immediate transfer, Calculation transfer and Chain transfer functions
CRC-CCITT
16 bits x 16 bits
15 bits x 1 channel (with prescaler)
40 internal and 8 external sources, 5 software sources
Interrupt priority level: 7
4 circuits
Main clock oscillation circuit(*), Sub clock oscillation circuit(*), On-chip
oscillator, PLL frequency synthesizer
(*)Equipped with a built-in feedback resistor. Ceramic resonator or
crystal oscillator must be connected externally
Main clock oscillation stop detect function
On-chip (option)
VCC=4.2 V to 5.5 V, (f(BCLK)=32 MHz)
28 mA (VCC=5 V, f(BCLK)=32 MHz)
10µA (VCC=5 V, f(BCLK)=32 kHz, in wait mode)
5.0 V ± 0.5 V
100 times (all space)
–40 to 85oC (T version)
–40 to 105oC (U version)
144-pin plastic molded LQFP
NOTES:
1. IEBus is a trademark of NEC Electronics Corporation.
2. I2C bus is a trademark of Koninklijke Philips Electronics N. V.
All options are on a request basis.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 2
of 435
1. Overview
M32C/88 Group (M32C/88T)
Table 1.2 M32C/88 Group (M32C/88T) Performance (100-Pin Package)
Characteristic
Basic Instructions
Minimum Instruction Execution Time
Operating Mode
Address Space
Memory Capacity
Peripheral I/O Port
Function Multifunction Timer
CPU
Intelligent I/O
Serial I/O
CAN Module
A/D Converter
D/A Converter
DMAC
DMAC II
CRC Calculation Circuit
X/Y Converter
Watchdog Timer
Interrupt
Clock Generation Circuit
Oscillation Stop Detect Function
Cold Start-up/Warm Start-up
Determine Function
Electrical Supply Voltage
Charact- Power Consumption
eristics
Flash
Program/Erase Supply Voltage
Memory Program and Erase Endurance
Operating Ambient Temperature
Package
Performance
108 instructions
31.3 ns (f(BCLK)=32 MHz, VCC=4.2 V to 5.5 V)
Single-chip mode
16 Mbytes
See Table 1.3
87 I/O pins and 1 input pin
Timer A: 16 bits x 5 channels, Timer B: 16 bits x 6 channels
Three-phase motor control circuit
Time measurement function or Waveform generating function:
16 bits x 8 channels
Communication function (Clock synchronous serial I/O, Clock asynchronous serial I/O, HDLC data processing)
5 Channels
Clock synchronous serial I/O, Clock asynchronous serial I/O,
IEBus(1), I2C bus(2)
3 channels Supporting CAN 2.0B specification
10-bit A/D converter: 1 circuit, 34 channels
8 bits x 2 channels
4 channels
Can be activated by all peripheral function interrupt sources
Immediate transfer, Calculation transfer and Chain transfer functions
CRC-CCITT
16 bits x 16 bits
15 bits x 1 channel (with prescaler)
40 internal and 8 external sources, 5 software sources
Interrupt priority level: 7
4 circuits
Main clock oscillation circuit(*), Sub clock oscillation circuit(*), On-chip
oscillator, PLL frequency synthesizer
(*)Equipped with a built-in feedback resistor. Ceramic resonator or
crystal oscillator must be connected externally
Main clock oscillation stop detect function
On-chip (option)
VCC=4.2 V to 5.5 V, (f(BCLK)=32 MHz)
28 mA (VCC=5 V, f(BCLK)=32 MHz)
10µA (VCC=5 V, f(BCLK)=32 kHz, in wait mode)
5.0 V ± 0.5 V
100 times (all space)
–40 to 85oC (T version)
–40 to 105oC (U version)
100-pin plastic molded LQFP
NOTES:
1. IEBus is a trademark of NEC Electronics Corporation.
2. I2C bus is a trademark of Koninklijke Philips Electronics N. V.
All options are on a request basis.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 3
of 435
1. Overview
M32C/88 Group (M32C/88T)
1.3 Block Diagram
Figure 1.1 shows a block diagram of the M32C/88 Group (M32C/88T) microcomputer.
8
8
8
8
8
8
8
Port P0
Port P1
Port P2
Port P3
Port P4
Port P5
Port P6
Peripheral Functions
Timer (16 bits)
Timer A: 5 channels
Timer B: 6 channels
UART/Clock Synchronous Serial I/O:
5 channels
DMAC
DMACII
CAN Module: 3 channels
7
X/Y Converter:
16 bits X 16 bits
D/A Converter:
8 bits X 2 channels
Port P8
Watchdog Timer (15 bits)
8
Three-Phase Motor Control Circuit
Port P7
Clock Generation Circuit
XIN - XOUT
XCIN - XCOUT
On-chip Oscillator
PLL Frequency Synthesizer
A/D Converter:
1 circuit
Standard: 10 inputs
Maximum: 34 inputs(2)
CRC Calculation Circuit (CCITT):
X16+X12+X5+1
P85
M32C/80 series CPU Core
Time Measurement: 8 channels
Wave Generating: 8 channels
Communication Functions:
Clock Synchronous Serial I/O,
UART,
HDLC Data Processing
Port P14
7
Port P15
8
Port P11
5
FLG
INTB
R2
ISP
R3
USP
A0
SVF
FB
SVP
SB
VCT
Port P13
8
8
(Note 1)
NOTES:
1. Ports P11 to P15 are provided in the 144-pin package only.
2. Included in the 144-pin package only.
Figure 1.1 M32C/88 Group (M32C/88T) Block Diagram
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 4
of 435
RAM
PC
A1
Port P12
ROM
Multiplier
8
R1L
8
R0L
R1H
Port P10
R0H
Memory
Port P9
Intelligent I/O
1. Overview
M32C/88 Group (M32C/88T)
1.4 Product Information
Table 1.3 lists the product information. Figure 1.2 shows the product numbering system.
Table 1.3 M32C/88 Group (1) (T version, M32C/88T)
Type Number
Package Type
M30882FJTGP
(D)
PLQP0144KA-A (144P6Q-A)
M30880FJTGP
(D)
PLQP0100KB-A (100P6Q-A)
M30882FHTGP
(D)
PLQP0144KA-A (144P6Q-A)
M30880FHTGP
(D)
PLQP0100KB-A (100P6Q-A)
M30882FWTGP
(D)
PLQP0144KA-A (144P6Q-A)
M30880FWTGP
(D)
PLQP0100KB-A (100P6Q-A)
As of October, 2005
ROM
Capacity
RAM
Capacity
Remarks
18K
Flash Memory
T version
(High-reliability
85° C)
512K+4K
384K+4K
320K+4K
(D): Under development
Table 1.3 M32C/88 Group (2) (U version, M32C/88T)
Type Number
Package Type
M30882FJUGP
(D)
PLQP0144KA-A (144P6Q-A)
M30880FJUGP
(D)
PLQP0100KB-A (100P6Q-A)
M30882FHUGP
(D)
PLQP0144KA-A (144P6Q-A)
M30880FHUGP
(D)
PLQP0100KB-A (100P6Q-A)
M30882FWUGP
(D)
PLQP0144KA-A (144P6Q-A)
M30880FWUGP
(D)
PLQP0100KB-A (100P6Q-A)
As of October, 2005
ROM
Capacity
RAM
Capacity
Remarks
18K
Flash Memory
U version
(High-reliability
105° C)
512K+4K
384K+4K
320K+4K
(D): Under development
NOTE:
Contact our sales office if you are interested in the V version.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 5
of 435
1. Overview
M32C/88 Group (M32C/88T)
M30 88 0 F H T GP
Package Type:
GP = Package PLQP0100KB-A (100P6Q-A)
Package PLQP0144KA-A (144P6Q-A)
Classification:
T = T Version
U = U Version
ROM Capacity:
W = 320 Kbytes
H = 384 Kbytes
J = 512 Kbytes
Memory Type:
F = Flash Memory Version
RAM Capacity, Pin Count, etc
M32C/88 Group
M16C Family
Figure 1.2 Product Numbering System
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 6
of 435
1. Overview
M32C/88 Group (M32C/88T)
1.5 Pin Assignment
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
109
72
110
71
111
70
112
69
113
68
114
67
115
66
116
65
117
64
118
63
119
62
120
61
121
60
122
59
123
58
124
57
M32C/88 GROUP
(M32C/88T)
125
126
127
128
56
55
54
53
NOTES:
1. P70 / TA0OUT / TxD2 / SDA2 / SRxD2 / INPC16 / OUTC16
2. P70 and P71 are ports for the N-channel open drain output.
Figure 1.3 Pin Assignment for 144-Pin Package
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 7
of 435
P44
P45
P46
P47
P125
P126
P127
P50
P51
P52
P53 / CLKOUT
P130
P131
Vcc
P132
Vss
P133
P54
P55
P56
P57
P134
P135
P136
P137
P60 / CTS0 / RTS0 / SS0 / CAN2OUT
P61 / CLK0 / CAN2IN / CAN2WU
P62 / RxD0 / SCL0 / STxD0
P63 / TxD0 / SDA0 / SRxD0
P64 / CTS1 / RTS1 / SS1
P65 / CLK1
Vss
P66 / RxD1 / SCL1 / STxD1
Vcc
P67 / TxD1 / SDA1 / SRxD1
P70(1, 2)
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
CAN1OUT / SRxD4 / SDA4 / TxD4 / ANEX1 / P96
CAN1WU / CAN1IN / CLK4 / ANEX0 / P95
SS4 / RTS4 / CTS4 / TB4IN / DA1 / P94
SS3 / RTS3 / CTS3 / TB3IN / DA0 / P93
SRxD3 / SDA3 / TxD3 / TB2IN / P92
STxD3 / SCL3 / RxD3 / TB1IN / P91
CLK3 / TB0IN / P90
P146
P145
P144
OUTC17 / INPC17 / P143
OUTC16 / INPC16 / P142
OUTC15 / INPC15 / P141
OUTC14 / INPC14 / P140
BYTE
CNVss
XCIN / P87
XCOUT / P86
RESET
XOUT
Vss
XIN
Vcc
NMI / P85
INT2 / P84
CAN0IN / CAN1IN / INT1 / P83
CAN0OUT / CAN1OUT / INT0 / P82
INPC15 / OUTC15 / U / TA4IN / P81
ISRxD0 / U / TA4OUT / P80
ISCLK0 / INPC14 / OUTC14 / CAN0IN / CAN02IN / TA3IN / P77
ISTxD0 / INPC13 / OUTC13 / CAN0OUT / CAN02OUT / TA3OUT / P76
BE1IN / ISRxD1 / OUTC12 / INPC12 / W / TA2IN / P75
ISCLK1 / OUTC11 / INPC11 / W / TA2OUT / P74
BE1OUT / ISTxD1 / OUTC10 / INPC10 / SS2 / RTS2 / CTS2 / V / TA1IN / P73
CLK2 / V / TA1OUT / P72
(2)INPC17 / OUTC17 / STxD2 / SCL2 / RxD2 / TA0IN / TB5IN / P71
18
37
17
38
144
16
39
143
15
40
142
14
41
141
13
42
140
12
43
139
11
44
138
10
45
137
9
46
136
8
47
135
7
48
134
6
49
133
5
50
132
4
51
131
3
52
130
2
129
1
P10
AN07 / P07
AN06 / P06
AN05 / P05
AN04 / P04
P114
OUTC13 / INPC13 / P113
BE1IN / ISRxD1 / OUTC12 / INPC12 / P112
ISCLK1 / OUTC11 / INPC11 / P111
BE1OUT / ISTxD1 / OUTC10 / INPC10 / P110
AN03 / P03
AN02 / P02
AN01 / P01
AN00 / P00
AN157 / P157
AN156 / P156
AN155 / P155
AN154 / P154
AN153 / P153
ISRxD0 / AN152 / P152
ISCLK0 / AN151 / P151
Vss
ISTxD0 / AN150 / P150
Vcc
KI3 / AN7 / P107
KI2 / AN6 / P106
KI1 / AN5 / P105
KI0 / AN4 / P104
AN3 / P103
AN2 / P102
AN1 / P101
AVss
AN0 / P100
VREF
AVcc
STxD4 / SCL4 / RxD4 / ADTRG / P97
107
108
P11
P12
P13
P14
P15 / INT3
P16 / INT4
P17 / INT5
P20 / AN20
P21 / AN21
P22 / AN22
P23 / AN23
P24 / AN24
P25 / AN25
P26 / AN26
P27 / AN27
Vss
P30
Vcc
P120
P121
P122
P123
P124
P31
P32
P33
P34
P35
P36
P37
P40
P41
Vss
P42
Vcc
P43
Figures 1.3 and 1.4 show pin assignments (top view).
PLQP0144KA-A
(144P6Q-A)
1. Overview
M32C/88 Group (M32C/88T)
Table 1.4 Pin Characteristics for 144-Pin Package
Pin
No.
Control
Pin
Port
Interrupt
Pin
Timer Pin
UART/CAN Pin
Intelligent I/O Pin
Analog Pin
1
P96
TxD4/SDA4/SRxD4/CAN1OUT
ANEX1
2
3
P95
CLK4/CAN1IN/CAN1WU
P94
TB4IN
CTS4/RTS4/SS4
ANEX0
DA1
4
P93
TB3IN
5
6
P92
TB2IN
CTS3/RTS3/SS3
TxD3/SDA3/SRxD3
P91
TB1IN
RxD3/SCL3/STxD3
7
P90
TB0IN
CLK3
8
9
P146
10
P144
11
12
P143
INPC17/OUTC17
P142
INPC16/OUTC16
13
P141
INPC15/OUTC15
14
15 BYTE
16 CNVSS
P140
INPC14/OUTC14
17 XCIN
18 XCOUT
19 RESET
20 XOUT
P87
DA0
P145
P86
21 VSS
22 XIN
23 VCC
24
25
26
P85
27
28
29
P82
P80
TA4IN/U
TA4OUT/U
30
31
32
33
34
35
36
37
38 VCC
39 VSS
40
41
42
43
44
45
46
47
48
P77
TA3IN
CAN0IN/CAN02IN
ISRxD0
INPC14/OUTC14/ISCLK0
P76
TA3OUT
CAN0OUT/CAN02OUT
INPC13/OUTC13/ISTxD0
P75
P74
TA2IN/W
TA2OUT/W
P73
P72
TA1IN/V
TA1OUT/V
P71
TB5IN/TA0IN
P70
TA0OUT
P84
P83
P81
NMI
INT2
CAN0IN/CAN1IN
INT1
INT0
CAN0OUT/CAN1OUT
INPC15/OUTC15
INPC12/OUTC12/ISRxD1/BE1IN
P67
CTS2/RTS2/SS2
CLK2
RxD2/SCL2/STxD2
TxD2/SDA2/SRxD2
TxD1/SDA1/SRxD1
P66
RxD1/SCL1/STxD1
P65
CLK1
CTS1/RTS1/SS1
TxD0/SDA0/SRxD0
RxD0/SCL0/STxD0
P64
P63
P62
CLK0/CAN2IN/CAN2WU
P61
P60
CTS0/RTS0/SS0/CAN2OUT
P137
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 8
of 435
INPC11/OUTC11/ISCLK1
INPC10/OUTC10/ISTxD1/BE1OUT
INPC17/OUTC17
INPC16/OUTC16
1. Overview
M32C/88 Group (M32C/88T)
Table 1.4 Pin Characteristics for 144-Pin Package (Continued)
Pin
No.
Control
Pin
Port
49
P136
50
51
P135
52
P57
53
54
P56
55
P54
P133
56
57
Analog Pin
P132
VCC
P131
P130
P53
64
P51
P50
P52
65
66
P127
67
68
69
P126
P125
P47
P46
70
71
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
Intelligent I/O Pin
VSS
62
63
75
76
77
UART/CAN Pin
P55
61
72
73
74
Timer Pin
P134
58
59
60
Interrupt
Pin
P45
P44
VCC
P43
VSS
P42
P41
P40
P37
P36
P35
P34
P33
P32
P31
P124
P123
P122
P121
VCC
P120
VSS
P30
P27
AN27
P26
AN26
P25
AN25
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 9
of 435
1. Overview
M32C/88 Group (M32C/88T)
Table 1.4 Pin Characteristics for 144-Pin Package (Continued)
Pin
No.
Control
Pin
Port
Interrupt
Pin
Timer Pin
UART/CAN Pin
Intelligent I/O Pin
Analog Pin
97
P24
AN24
98
99
P23
AN23
P22
AN22
100
P21
AN21
101
102
P20
P17
INT5
103
P16
P15
INT4
INT3
104
105
AN20
P14
106
P13
107
108
P12
109
P10
110
111
P07
AN07
P06
AN06
112
P05
P04
AN05
AN04
P11
113
114
P114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
P113
INPC13/OUTC13
P112
INPC12/OUTC12/ISRxD1/BE1IN
P111
P110
INPC11/OUTC11/ISCLK1
INPC10/OUTC10/ISTxD1/BE1OUT
P03
AN03
P02
AN02
P01
AN01
P00
P157
AN00
AN157
P156
AN156
P155
AN155
P154
AN154
P153
AN153
P152
AN152
P151
ISRxD0
ISCLK0
P150
ISTxD0
AN150
AN151
VSS
VCC
P107
KI3
AN7
P106
KI2
AN6
P105
KI1
AN5
P104
KI0
AN4
P103
AN3
P102
AN2
P101
AN1
P100
AN0
AVSS
VREF
AVCC
RxD4/SCL4/STxD4
P97
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 10 of 435
ADTRG
1. Overview
P36
P37
P40
P41
52
51
P31
59
53
Vcc
60
P35
P30
61
54
Vss
62
P34
P27 / AN27
63
55
P26 / AN26
64
56
P25 / AN25
65
P32
P24 / AN24
66
P33
P23 / AN23
67
57
P22 / AN22
68
58
P20 / AN20
P21 / AN21
69
P17 / INT5
71
70
P15 / INT3
P16 / INT4
72
P14
74
73
P13
75
M32C/88 Group (M32C/88T)
P12
76
50
P42
P11
77
49
P43
P10
78
48
P44
AN07 / P07
79
47
P45
AN06 / P06
80
46
P46
AN05 / P05
81
45
P47
AN04 / P04
82
44
P50
AN03 / P03
83
43
P51
AN02 / P02
84
42
P52
AN01 / P01
85
41
P53 / CLKOUT
M32C/88 GROUP
(M32C/88T)
40
P54
39
P55
38
P56
37
P57
90
36
P60 / CTS0 / RTS0 / SS0 / CAN2OUT
AN3 / P103
91
35
P61 / CLK0 / CAN2IN / CAN2WU
AN2 / P102
92
34
P62 / RxD0 / SCL0 / STxD0
AN1 / P101
93
33
P63 / TxD0 / SDA0 / SRxD0
AN00 / P00
86
KI3 / AN7 / P107
87
KI2 / AN6 / P106
88
KI1 / AN5 / P105
89
KI0 / AN4 / P104
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 11 of 435
24
25
ISCLK1 / OUTC11 / INPC11 / W / TA2OUT / P74
19
OUTC15 / INPC15 / U / TA4IN / P81
BE1OUT / ISTxD1 / OUTC10 / SS2 / INPC10 / RTS2 / CTS2 / V / TA1IN / P73
18
CAN0OUT / CAN1OUT / INT0 / P82
23
17
CAN0IN / CAN1IN / INT1 / P83
BE1IN / ISRxD1 / OUTC12 / INPC12 / W / TA2IN / P75
16
INT2 / P84
22
15
NMI / P85
ISTxD0 / OUTC13 / INPC13 / CAN0OUT / CAN02OUT / TA3OUT / P76
14
Vcc
21
13
XIN
20
12
Vss
Figure 1.4 Pin Assignment for 100-Pin Package
ISRxD0 / U / TA4OUT / P80
11
XOUT
NOTES:
1. P70 / TA0OUT / TxD2 / SDA2 / SRxD2 / OUTC16 / INPC16
2. P71 / TA0IN / TB5IN / RxD2 / SCL2 / STxD2 / OUTC17 / INPC17
3. P96 / ANEX1 / TxD4 / SDA4 / SRxD4 / CAN1OUT
4. P70 and P71 are ports for the N-channel open drain output.
ISCLK0 / OUTC14 / INPC14 / CAN0IN / CAN02IN / TA3IN / P77
10
P72 / TA1OUT / V / CLK2
RESET
26
9
100
8
CAN1WU / CAN1IN / CLK4 / ANEX0 / P95
XCIN / P87
P71(2, 4)
XCOUT / P86
99
27
7
P70
P96
(3)
CNVss
28
6
98
5
P67 / TxD1 / SDA1 / SRxD1
STxD4 / SCL4 / RxD4 / ADTRG / P97
BYTE
29
CLK3 / TB0IN / P90
97
4
P66 / RxD1 / SCL1 / STxD1
AVcc
STxD3 / SCL3 / RxD3 / TB1IN / P91
30
3
96
SRxD3 / SDA3 / TxD3 / TB2IN / P92
P65 / CLK1
VREF
2
P64 / CTS1 / RTS1 / SS1
31
1
32
95
SS3 / RTS3 / CTS3 / TB3IN / DA0 / P93
94
SS4 / RTS4 / CTS4 / TB4IN / DA1 / P94
AVss
AN0 / P100
(1, 4)
PLQP0100KB-A
(100P6Q-A)
1. Overview
M32C/88 Group (M32C/88T)
Table 1.5 Pin Characteristics for 100-Pin Package
Pin
No.
Control
Pin
Port
Interrupt
Pin
Timer Pin
UART/CAN Pin
1
2
P94
P93
TB4IN
TB3IN
CTS4/RTS4/SS4
CTS3/RTS3/SS3
3
4
5
P92
P91
P90
TB2IN
TB1IN
TB0IN
TxD3/SDA3/SRxD3
RxD3/SCL3/STxD3
CLK3
6
7
8
BYTE
CNVSS
XCIN
P87
9
10
XCOUT
RESET
XOUT
P86
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Intelligent I/O Pin
DA1
DA0
VSS
XIN
VCC
P85
P84
P83
P82
P81
P80
P77
P76
P75
P74
P73
P72
P71
P70
P67
P66
NMI
INT2
CAN0IN/CAN1IN
CAN0OUT/CAN1OUT
INT1
INT0
TA4IN/U
TA4OUT/U
TA3IN
TA3OUT
TA2IN/W
TA2OUT/W
TA1IN/V
TA1OUT/V
TB5IN/TA0IN
TA0OUT
P65
P64
P63
P62
P61
P60
P57
P56
P55
P54
P53
P52
P51
P50
P47
P46
P45
P44
P43
P42
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 12 of 435
INPC15/OUTC15
CAN0IN/CAN02IN
CAN0OUT/CAN02OUT
Analog
Pin
ISRxD0
INPC14/OUTC14/ISCLK0
INPC13/OUTC13/ISTxD0
INPC12/OUTC12/ISRxD1/BE1IN
INPC11/OUTC11/ISCLK1
CTS2/RTS2/SS2
INPC10/OUTC10/ISTxD1/BE1OUT
CLK2
RxD2/SCL2/STxD2
INPC17/OUTC17
TxD2/SDA2/SRxD2
INPC16/OUTC16
TxD1/SDA1/SRxD1
RxD1/SCL1/STxD1
CLK1
CTS1/RTS1/SS1
TxD0/SDA0/SRxD0
RxD0/SCL0/STxD0
CLK0/CAN2IN/CAN2WU
CTS0/RTS0/SS0/CAN2OUT
1. Overview
M32C/88 Group (M32C/88T)
Table 1.5 Pin Characteristics for 100-Pin Package (Continued)
Pin
No.
Control
Pin
51
52
Analog
Pin
P31
VCC
P30
VSS
P27
P26
AN27
AN26
P25
AN25
P24
P23
P22
AN24
AN23
AN22
P21
AN21
P20
P17
P16
P15
AN20
INT5
INT4
INT3
P14
P13
P12
P11
84
85
86
P10
P07
AN07
P06
P05
AN06
AN05
P04
P03
AN04
AN03
P02
P01
AN02
AN01
P00
P107
87
88
89
P106
P105
90
91
92
99
100
Intelligent I/O Pin
P34
P33
P32
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
96
97
98
UART/CAN Pin
P35
65
66
67
93
94
95
Timer Pin
P40
P37
P36
56
57
58
62
63
64
Interrupt
Pin
P41
53
54
55
59
60
61
Port
P104
AN00
AN7
KI3
KI2
AN6
AN5
KI1
KI0
AN4
P103
P102
P101
AN3
AN2
AN1
P100
AN0
AVSS
VREF
AVCC
P97
P96
RxD4/SCL4/STxD4
TxD4/SDA4/SRxD4/CAN1OUT
P95
CLK4/CAN1IN/CAN1WU
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 13 of 435
ADTRG
ANEX1
ANEX0
1. Overview
M32C/88 Group (M32C/88T)
1.6 Pin Description
Table 1.6 Pin Description (100-Pin and 144-Pin Packages)
Classsfication
Symbol
I/O Type
Function
Power Supply
VCC
I
Apply 4.2 to 5.5 V to both VCC pins.
Analog Power
VSS
AVCC
I
Apply 0 V to the VSS pin
Supplies power to the A/D converter. Connect the AVCC pin to VCC and the
Supply
Reset Input
AVSS
____________
RESET
I
AVSS pin to VSS
___________
The microcomputer is in a reset state when "L" is applied to the RESET pin
CNVSS
CNVSS
Input to Switch BYTE
I
I
Switches processor mode. Connect the CNVSS pin to VSS
Connect the BYTE pin to VSS
Main Clock Input XIN
I
I/O pins for the main clock oscillation circuit. Connect a ceramic resonator
Main Clock Output XOUT
O
Sub Clock Input XCIN
I
Sub Clock output XCOUT
O
O
Outputs the clock having the same frequency as fC, f8 or f32
I
Input pins for the INT interrupt
I
I
Input pin for the NMI interrupt
Input pins for the key input interrupt
External Data Bus
Width
Clock Output
CLKOUT
______
________
INT Interrupt
Input
INT0 to
________
INT5
_______
_______
Timer B
TA0OUT to
TA4OUT
between XCIN and XCOUT. To apply external clock, apply it to XCIN and
leave XCOUT open
I/O
I/O pins for the timer A0 to A4
(TA0OUT is a pin for the N-channel open drain output.)
TA0IN to
TA4IN
I
Input pins for Timer A0 to A4
TB0IN to
TB5IN
I
Input pins for Timer B0 to B5
O
Output pins for the three-phase motor control timer
CTS0 to CTS4
_________
_________
RTS0 to RTS4
I
O
Input pins for data transmission control
Output pins for data reception control
CLK0 to
CLK4
I/O
Inputs and outputs the transfer clock
RxD0 to
RxD4
I
Inputs serial data
TxD0 to
TxD4
O
Outputs serial data
(TxD2 is a pin for the N-channel open drain output.)
SDA0 to
SDA4
I/O
Inputs and outputs serial data
(SDA2 is a pin for the N-channel open drain output.)
___
_________
I2C Mode
I/O pins for the sub clock oscillation circuit. Connect a crystal oscillator
_______
___
Three-phase Motor U, U, V, V,
___
Control Timer Output W, W
Serial I/O
to XIN and leave XOUT open.
______
NMI Interrupt Input NMI
_____
_____
Key Input Interrupt KI0 to KI3
Timer A
or crystal oscillator between XIN and XOUT. To apply external clock, apply it
________
SCL0 to
SCL4
Inputs and outputs the transfer clock
(SCL2 is a pin for the N-channel open drain output.)
Serial I/O
STxD0 to
Special Function STxD4
O
Outputs serial data when slave mode is selected
(STxD2 is a pin for the N-channel open drain output.)
SRxD0 to
SRxD4
I
Inputs serial data when slave mode is selected
I
Input pins to control serial I/O special function
_______
_______
SS0 to SS4
I : Input
O : Output
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
I/O : Input and output
Page 14 of 435
1. Overview
M32C/88 Group (M32C/88T)
Table 1.6 Pin Description (100-Pin and 144-Pin Packages) (Continued)
Classsfication
Symbol
I/O Type
Function
Reference
VREF
I
Applies reference voltage to the A/D converter and D/A converter
Voltage Input
A/D Converter
AN0 to AN7
I
Analog input pins for the A/D converter
AN00 to AN07
AN20 to AN27
___________
D/A Converter
Intelligent I/O
CAN
ADTRG
ANEX0
I
I/O
Input pin for an external A/D trigger
Extended analog input pin for the A/D converter and output pin in external
ANEX1
I
op-amp connection mode
Extended analog input pin for the A/D converter
DA0, DA1
INPC10 to
O
I
Output pin for the D/A converter
Input pins for the time measurement function
INPC17
OUTC10 to
O
Output pins for the waveform generating function
OUTC17
ISCLK0
I/O
(OUTC16 and OUTC17 assigned to P70 and P71 are pins for the N-channel open drain output.)
Inputs and outputs the clock for the intelligent I/O communication function
ISCLK1
ISRXD0
I
Inputs data for the intelligent I/O communication function
ISRXD1
ISTXD0
O
Outputs data for the intelligent I/O communication function
ISTXD1
BE1IN
I
Inputs data for the intelligent I/O communication function
BE1OUT
CAN0IN
O
I
Outputs data for the intelligent I/O communication function
Input pin for the CAN communication function
O
Output pin for the CAN communication function
I
Input pin for the CANi wake-up interrupt (i=1, 2)
CAN02IN
CAN1IN
CAN2IN
CAN0OUT
CAN02OUT
CAN1OUT
CAN2OUT
_______________
CAN1WU
________________
I/O Ports
CAN2WU
P00 to P07
I/O
under the control of the direction register. An input port can be set, by
program, for a pull-up resistor available or for no pull-up resister available in
P30 to P37
P40 to P47
4-bit units
P50 to P57
P60 to P67
I/O
P70 to P77
P90 to P97
P100 to P107
P80 to P84
Input Port
I : Input
8-bit I/O ports for CMOS. Each port can be programmed for input or output
P10 to P17
P20 to P27
P86, P87
P85
O : Output
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
I/O ports having equivalent functions to P0
(P70 and P71 are ports for the N-channel open drain output.)
I/O
I/O ports having equivalent functions to P0
_______
I
I/O : Input and output
Page 15 of 435
_______
Shares a pin with NMI. NMI input state can be got by reading P8 5
1. Overview
M32C/88 Group (M32C/88T)
Table 1.6 Pin Description (144-Pin Package Only) (Continued)
Classsfication
Symbol
I/O Type
A/D Converter
AN150 to
AN157
I
I/O Ports
P110 to
P114
I/O
Function
Analog input pins for the A/D converter
I/O ports having equivalent functions to P0
P120 to
P127
P130 to
P137
P140 to
P146
P150 to
P157
I : Input
O : Output
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
I/O : Input and output
Page 16 of 435
2. Central Processing Unit (CPU)
M32C/88 Group (M32C/88T)
2. Central Processing Unit (CPU)
Figure 2.1 shows the CPU registers.
The register bank is comprised of 8 registers (R0, R1, R2, R3, A0, A1, SB and FB) out of 28 CPU registers.
Two sets of register banks are provided.
b31
b15
General Registers
b0
R2
R0H
R3
R1H
R0L
R1L
Data Register(1)
R2
R3
b23
A0
Address Register(1)
A1
SB
Static Base Register(1)
FB
Frame Base Register(1)
USP
User Stack Pointer
ISP
Interrupt Stack Pointer
INTB
Interrupt Table Register
Program Counter
PC
FLG
b15
Flag Register
b8 b7
IPL
b0
U I O B S Z D C
Carry Flag
Debug Flag
Zero Flag
Sign Flag
Register Bank Select Flag
Overflow Flag
Interrupt Enable Flag
Stack Pointer Select Flag
Reserved Space
Processor Interrupt Priority Level
Reserved Space
b15
High-speed Interrupt Registers
b0
SVF
b23
Flag Save Register
SVP
PC Save Register
VCT
Vector Register
b7
DMAC-associated Registers
b0
DMD0
DMD1
b15
DCT0
DCT1
DMA Mode Register
DMA Transfer Count Register
DRC0
DRC1
b23
DMA Transfer Count Reload Register
DMA0
DMA1
DMA Memory Address Register
DRA0
DRA1
DMA Memory Address Reload Register
DSA0
DSA1
DMA SFR Address Register
NOTE:
1. The register bank is comprised of these registers. Two sets of register banks are provided.
Figure 2.1 CPU Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 17 of 435
M32C/88 Group (M32C/88T)
2. Central Processing Unit (CPU)
2.1 General Registers
2.1.1 Data Registers (R0, R1, R2 and R3)
R0, R1, R2 and R3 are 16-bit registers for transfer, arithmetic and logic operations. R0 and R1 can be
split into high-order bits (R0H) and low-order bits (R0L) to be used separately as 8-bit data registers.
R0 can be combined with R2 to be used as a 32-bit data register (R2R0). The same applies to R1 and
R3.
2.1.2 Address Registers (A0 and A1)
A0 and A1 are 24-bit registers for A0-/A1-indirect addressing, A0-/A1-relative addressing, transfer, arithmetic and logic operations.
2.1.3 Static Base Register (SB)
SB is a 24-bit register for SB-relative addressing.
2.1.4 Frame Base Register (FB)
FB is a 24-bit register for FB-relative addressing.
2.1.5 Program Counter (PC)
PC, 24 bits wide, indicates the address of an instruction to be executed.
2.1.6 Interrupt Table Register (INTB)
INTB is a 24-bit register indicating the starting address of an relocatable interrupt vector table.
2.1.7 User Stack Pointer (USP), Interrupt Stack Pointer (ISP)
The stack pointers (SP), USP and ISP, are 24 bits wide each. The U flag is used to switch between USP
and ISP. Refer to 2.1.8 Flag Register (FLG) for details on the U flag. Set USP and ISP to even
addresses to execute an interrupt sequence efficiently.
2.1.8 Flag Register (FLG)
FLG is a 16-bit register indicating a CPU state.
2.1.8.1 Carry Flag (C)
The C flag indicates whether carry or borrow has occurred after executing an instruction.
2.1.8.2 Debug Flag (D)
The D flag is for debug only. Set to "0".
2.1.8.3 Zero Flag (Z)
The Z flag is set to "1" when the value of zero is obtained from an arithmetic operation; otherwise "0".
2.1.8.4 Sign Flag (S)
The S flag is set to "1" when a negative value is obtained from an arithmetic operation; otherwise "0".
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 18 of 435
M32C/88 Group (M32C/88T)
2. Central Processing Unit (CPU)
2.1.8.5 Register Bank Select Flag (B)
The register bank 0 is selected when the B flag is set to "0". The register bank 1 is selected when this
flag is set to "1".
2.1.8.6 Overflow Flag (O)
The O flag is set to "1" when the result of an arithmetic operation overflows; otherwise "0".
2.1.8.7 Interrupt Enable Flag (I)
The I flag enables a maskable interrupt.
Interrupt is disabled when the I flag is set to "0" and enabled when the I flag is set to "1". The I flag is
set to "0" when an interrupt is acknowledged.
2.1.8.8 Stack Pointer Select Flag (U)
ISP is selected when the U flag is set to "0". USP is selected when this flag is set to "1".
The U flag is set to "0" when a hardware interrupt is acknowledged or the INT instruction of software
interrupt numbers 0 to 31 is executed.
2.1.8.9 Processor Interrupt Priority Level (IPL)
IPL, 3 bits wide, assigns processor interrupt priority levels from level 0 to level 7.
If a requested interrupt has greater priority than IPL, the interrupt is enabled.
2.1.8.10 Reserved Space
When writing to a reserved space, set to "0". When reading, its content is indeterminate.
2.2 High-Speed Interrupt Registers
Registers associated with the high-speed interrupt are as follows:
- Flag save register (SVF)
- PC save register (SVP)
- Vector register (VCT)
Refer to 10.4 High-Speed Interrupt for details.
2.3 DMAC-Associated Registers
Registers associated with DMAC are as follows:
- DMA mode register (DMD0, DMD1)
- DMA transfer count register (DCT0, DCT1)
- DMA transfer count reload register (DRC0, DRC1)
- DMA memory address register (DMA0, DMA1)
- DMA SFR address register (DSA0, DSA1)
- DMA memory address reload register (DRA0, DRA1)
Refer to 12. DMAC for details.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 19 of 435
3. Memory
M32C/88 Group (M32C/88T)
3. Memory
Figure 3.1 shows a memory map of the M32C/88 Group (M32C/88T).
The M32C/88 Group (M32C/88T) provides 16-Mbyte address space addressed from 000000 16 to
FFFFFF16.
The internal ROM is allocated from address FFFFFF16 to lower. For example, a 64-Kbyte internal ROM is
addressed from FF000016 to FFFFFF16.
The fixed interrupt vectors are allocated from address FFFFDC16 to FFFFFF16. It stores the starting address of each interrupt routine.
The internal RAM is allocated from address 00040016 to higher. For example, a 10-Kbyte internal RAM is
allocated from address 00040016 to 002BFF16. Besides storing data, it becomes stacks when the subroutine is called or an interrupt is acknowledged.
SFRs, consisting of control registers for peripheral functions such as I/O port, A/D converter, serial I/O,
timers, is allocated from address 00000016 to 0003FF16. All blank spaces within SFRs are reserved and
cannot be accessed by users.
The special page vectors are addressed from FFFE0016 to FFFFDB16. It is used for the JMPS instruction
and JSRS instruction. Refer to the Renesas publication M32C/80 Series Software Manual for details.
00000016
SFRs
00040016
XXXXXX16
Internal RAM
Reserved Space
00F00016
FFFE00 16
Special Page
Vector Table
(1)
Internal ROM
(Data space)
Internal RAM
XXXXXX16
Capacity
18 Kbytes
004BFF16
Internal ROM
YYYYYY16
Capacity
FB000016
320 Kbytes
FA000016
384 Kbytes
F8000016
512 Kbytes
00FFFF16
FFFFDC 16
Undefined Instruction
Overflow
BRK Instruction
Address Match
Reserved Space
Watchdog Timer(2)
YYYYYY16
Internal ROM
FFFFFF16
FFFFFF 16
NOTES:
1. Additional 4-Kbyte space is provided in the flash memory version for storing data.
2. Watchdog timer interrupt and oscillation stop detection interrupt share vectors.
Figure 3.1 Memory Map
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 20 of 435
NMI
Reset
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
4. Special Function Registers (SFRs)
Address
000016
000116
000216
000316
000416
000516
000616
000716
000816
000916
000A16
000B16
000C16
000D16
000E16
000F16
001016
001116
001216
001316
001416
001516
001616
001716
001816
001916
001A16
001B16
001C16
001D16
001E16
001F16
002016
002116
002216
002316
002416
002516
002616
002716
002816
002916
002A16
002B16
002C16
002D16
002E16
002F16
Register
Symbol
Value after RESET
Processor Mode Register(1)
Processor Mode Register 1
System Clock Control Register 0
System Clock Control Register 1
PM0
PM1
CM0
CM1
1000 00002(CNVss pin ="L")
0016
0000 10002
0010 00002
Address Match Interrupt Enable Register
Protect Register
AIER
PRCR
0016
XXXX 00002
Main Clock Division Register
Oscillation Stop Detection Register
Watchdog Timer Start Register
Watchdog Timer Control Register
MCD
CM2
WDTS
WDC
XXX0 10002
0016
XX16
000X XXXX2
Address Match Interrupt Register 0
RMAD0
00000016
Processor Mode Register 2
PM2
0016
Address Match Interrupt Register 1
RMAD1
00000016
Address Match Interrupt Register 2
RMAD2
00000016
Address Match Interrupt Register 3
RMAD3
00000016
PLL Control Register 0
PLL Control Register 1
PLC0
PLC1
0001 X0102
000X 00002
Address Match Interrupt Register 4
RMAD4
00000016
Address Match Interrupt Register 5
RMAD5
00000016
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTE:
1. The PM01 and PM00 bits in the PM0 register maintain values set before reset, even after software reset or watchdog timer reset has been performed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 21 of 435
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
Address
006016
003016
003116
003216
003316
003416
003516
003616
003716
003816
003916
003A16
003B16
003C16
003D16
003E16
003F16
004016
004116
004216
004316
004416
004516
004616
004716
004816
004916
004A16
004B16
004C16
004D16
004E16
004F16
005016
005116
005216
005316
005416
005516
005616
005716
005816
005916
005A16
005B16
005C16
005D16
005E16
005F16
Register
Address Match Interrupt Register 6
Address Match Interrupt Register 7
Symbol
RMAD6
RMAD7
Value after RESET
00000016
00000016
Flash Memory Control Register 1
FMR1
0000 01012
Flash Memory Control Register 0
FMR0
0000 00012
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 22 of 435
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
Address
006016
006116
006216
006316
006416
006516
006616
006716
006816
006916
006A16
006B16
006C16
006D16
006E16
006F16
007016
007116
007216
007316
007416
007516
007616
007716
007816
007916
007A16
007B16
007C16
007D16
007E16
007F16
008016
008116
008216
008316
008416
008516
008616
008716
008816
008916
008A16
008B16
008C16
008D16
008E16
008F16
Register
Symbol
Value after RESET
DMA0 Interrupt Control Register
Timer B5 Interrupt Control Register
DMA2 Interrupt Control Register
UART2 Receive /ACK Interrupt Control Register
Timer A0 Interrupt Control Register
UART3 Receive /ACK Interrupt Control Register
Timer A2 Interrupt Control Register
UART4 Receive /ACK Interrupt Control Register
Timer A4 Interrupt Control Register
UART0/UART3 Bus Conflict Detect Interrupt Control Register
DM0IC
TB5IC
DM2IC
S2RIC
TA0IC
S3RIC
TA2IC
S4RIC
TA4IC
BCN0IC/BCN3IC
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
UART0 Receive/ACK Interrupt Control Register
A/D0 Conversion Interrupt Control Register
UART1 Receive/ACK Interrupt Control Register
Intelligent I/O Interrupt Control Register 0/
CAN Interrupt 3 Control Register
Timer B1 Interrupt Control Register
Intelligent I/O Interrupt Control Register 2/
CAN Interrupt 6 Control Register
Timer B3 Interrupt Control Register
Intelligent I/O Interrupt Control Register 4
INT5 Interrupt Control Register
CAN Interrupt 8 Control Register
INT3 Interrupt Control Register
Intelligent I/O Interrupt Control Register 8
INT1 Interrupt Control Register
Intelligent I/O Interrupt Control Register 10/
S0RIC
AD0IC
S1RIC
IIO0IC/
CAN3IC
TB1IC
IIO2IC/
CAN6IC
TB3IC
IIO4IC
INT5IC
CAN8IC
INT3IC
IIO8IC
INT1IC
IIO10IC/
XXXX X0002
XXXX X0002
XXXX X0002
CAN Interrupt 1 Control Register
CAN1IC
CAN Interrupt 2 Control Register
CAN2IC
XXXX X0002
DMA1 Interrupt Control Register
UART2 Transmit /NACK Interrupt Control Register
DMA3 Interrupt Control Register
UART3 Transmit /NACK Interrupt Control Register
Timer A1 Interrupt Control Register
UART4 Transmit /NACK Interrupt Control Register
Timer A3 Interrupt Control Register
UART2 Bus Conflict Detect Interrupt Control Register
DM1IC
S2TIC
DM3IC
S3TIC
TA1IC
S4TIC
TA3IC
BCN2IC
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 23 of 435
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XX00 X0002
XXXX X0002
XX00 X0002
XXXX X0002
XX00 X0002
XXXX X0002
M32C/88 Group (M32C/88T)
Address
009016
009116
009216
009316
009416
009516
009616
009716
009816
009916
009A16
009B16
009C16
009D16
009E16
009F16
00A016
00A116
00A216
00A316
00A416
00A516
00A616
00A716
00A816
00A916
00AA16
00AB16
00AC16
00AD16
00AE16
00AF16
00B016
00B116
00B216
00B316
00B416
00B516
00B616
00B716
00B816
00B916
00BA16
00BB16
00BC16
00BD16
00BE16
00BF16
4. Special Function Registers (SFRs)
Register
UART0 Transmit /NACK Interrupt Control Register
UART1/UART4 Bus Conflict Detect Interrupt Control Register
UART1 Transmit/NACK Interrupt Control Register
Key Input Interrupt Control Register
Timer B0 Interrupt Control Register
Intelligent I/O Interrupt Control Register 1/
CAN Interrupt 4 Control Register
Timer B2 Interrupt Control Register
Intelligent I/O Interrupt Control Register 3/
CAN Interrupt 7 Control Register
Timer B4 Interrupt Control Register
CAN Interrupt 5 Control Register
INT4 Interrupt Control Register
Symbol
S0TIC
BCN1IC/BCN4IC
S1TIC
KUPIC
TB0IC
IIO1IC/
CAN4IC
TB2IC
IIO3IC/
CAN7IC
TB4IC
CAN5IC
INT4IC
Value after RESET
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
INT2 Interrupt Control Register
Intelligent I/O Interrupt Control Register 9/
INT2IC
IIO9IC/
XX00 X0002
CAN Interrupt 0 Control Register
INT0 Interrupt Control Register
Exit Priority Control Register
Interrupt Request Register 0
Interrupt Request Register 1
Interrupt Request Register 2
Interrupt Request Register 3
Interrupt Request Register 4
Interrupt Request Register 5
Interrupt Request Register 6
CAN0IC
INT0IC
RLVL
IIO0IR
IIO1IR
IIO2IR
IIO3IR
IIO4IR
IIO5IR
IIO6IR
XX00 X0002
XXXX 00002
0000 000X2
0000 000X2
0000 000X2
0000 000X2
0000 000X2
0000 000X2
0000 000X2
Interrupt Request Register 8
Interrupt Request Register 9
Interrupt Request Register 10
Interrupt Request Register 11
IIO8IR
IIO9IR
IIO10IR
IIO11IR
0000 000X2
0000 000X2
0000 000X2
0000 000X2
Interrupt Enable Register 0
Interrupt Enable Register 1
Interrupt Enable Register 2
Interrupt Enable Register 3
Interrupt Enable Register 4
Interrupt Enable Register 5
Interrupt Enable Register 6
IIO0IE
IIO1IE
IIO2IE
IIO3IE
IIO4IE
IIO5IE
IIO6IE
0016
0016
0016
0016
0016
0016
0016
Interrupt Enable Register 8
Interrupt Enable Register 9
Interrupt Enable Register 10
Interrupt Enable Register 11
IIO8IE
IIO9IE
IIO10IE
IIO11IE
0016
0016
0016
0016
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 24 of 435
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XX00 X0002
XXXX X0002
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
Address
00C016
00C116
00C216
00C316
00C416
00C516
00C616
00C716
00C816
00C916
00CA16
00CB16
00CC16
00CD16
00CE16
00CF16
00D016
00D116
00D216
00D316
00D416
00D516
00D616
00D716
00D816
00D916
00DA16
00DB16
00DC16
00DD16
00DE16
00DF16
00E016
00E116
00E216
00E316
00E416
00E516
00E616
00E716
00E816
00E916
00EA16
00EB16
00EC16
00ED16
00EE16
00EF16
Register
Symbol
Value after RESET
SI/O Receive Buffer Register 0
G0RB
Transmit Buffer/Receive Data Register 0
G0TB/G0DR
XXXX XXXX2
XXX0 XXXX2
XX16
Receive Input Register 0
SI/O Communication Mode Register 0
Transmit Output Register 0
SI/O Communication Control Register 0
G0RI
G0MR
G0TO
G0CR
XX16
0016
XX16
0000 X0112
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 25 of 435
M32C/88 Group (M32C/88T)
Address
00F016
00F116
00F216
00F316
00F416
00F516
00F616
00F716
00F816
00F916
00FA16
00FB16
00FC16
00FD16
00FE16
00FF16
010016
010116
010216
010316
010416
010516
010616
010716
010816
010916
010A16
010B16
010C16
010D16
010E16
010F16
011016
011116
011216
011316
011416
011516
011616
011716
011816
011916
011A16
011B16
011C16
011D16
011E16
011F16
4. Special Function Registers (SFRs)
Register
Data Compare Register 00
Data Compare Register 01
Data Compare Register 02
Data Compare Register 03
Data Mask Register 00
Data Mask Register 01
Communication Clock Select Register
Symbol
G0CMP0
G0CMP1
G0CMP2
G0CMP3
G0MSK0
G0MSK1
CCS
Receive CRC Code Register 0
G0RCRC
Transmit CRC Code Register 0
G0TCRC
SI/O Extended Mode Register 0
SI/O Extended Receive Control Register 0
SI/O Special Communication Interrupt Detect Register 0
SI/O Extended Transmit Control Register 0
G0EMR
G0ERC
G0IRF
G0ETC
Time Measurement/Waveform Generating Register 10
G1TM0/G1PO0
Time Measurement/Waveform Generating Register 11
G1TM1/G1PO1
Time Measurement/Waveform Generating Register 12
G1TM2/G1PO2
Time Measurement/Waveform Generating Register 13
G1TM3/G1PO3
Time Measurement/Waveform Generating Register 14
G1TM4/G1PO4
Time Measurement/Waveform Generating Register 15
G1TM5/G1PO5
Time Measurement/Waveform Generating Register 16
G1TM6/G1PO6
Time Measurement/Waveform Generating Register 17
G1TM7/G1PO7
Waveform Generating Control Register 10
Waveform Generating Control Register 11
Waveform Generating Control Register 12
Waveform Generating Control Register 13
Waveform Generating Control Register 14
Waveform Generating Control Register 15
Waveform Generating Control Register 16
Waveform Generating Control Register 17
Time Measurement Control Register 10
Time Measurement Control Register 11
Time Measurement Control Register 12
Time Measurement Control Register 13
Time Measurement Control Register 14
Time Measurement Control Register 15
Time Measurement Control Register 16
Time Measurement Control Register 17
G1POCR0
G1POCR1
G1POCR2
G1POCR3
G1POCR4
G1POCR5
G1POCR6
G1POCR7
G1TMCR0
G1TMCR1
G1TMCR2
G1TMCR3
G1TMCR4
G1TMCR5
G1TMCR6
G1TMCR7
Value after RESET
XX16
XX16
XX16
XX16
XX16
XX16
XXXX 00002
XX16
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 26 of 435
XX16
0016
0016
0016
0016
0016
0000 0XXX2
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
0000 X0002
0X00 X0002
0X00 X0002
0X00 X0002
0X00 X0002
0X00 X0002
0X00 X0002
0X00 X0002
0016
0016
0016
0016
0016
0016
0016
0016
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
Address
012016
012116
012216
012316
012416
012516
012616
012716
012816
012916
012A16
012B16
012C16
012D16
012E16
012F16
013016
013116
013216
013316
013416
013516
013616
013716
013816
013916
013A16
013B16
013C16
013D16
013E16
013F16
014016
014116
014216
014316
014416
014516
014616
014716
014816
014916
014A16
014B16
014C16
014D16
to
016F16
Register
Symbol
Value after RESET
XX16
Base Timer Register 1
G1BT
Base Timer Control Register 10
Base Timer Control Register 11
Time Measurement Prescaler Register 16
Time Measurement Prescaler Register 17
Function Enable Register 1
Function Select Register 1
G1BCR0
G1BCR1
G1TPR6
G1TPR7
G1FE
G1FS
SI/O Receive Buffer Register 1
G1RB
Transmit Buffer/Receive Data Register 1
G1TB/G1DR
X000 XXXX2
XX16
Receive Input Register 1
SI/O Communication Mode Register 1
Transmit Output Register 1
SI/O Communication Control Register 1
Data Compare Register 10
Data Compare Register 11
Data Compare Register 12
Data Compare Register 13
Data Mask Register 10
Data Mask Register 11
G1RI
G1MR
G1TO
G1CR
G1CMP0
G1CMP1
G1CMP2
G1CMP3
G1MSK0
G1MSK1
XX16
0016
XX16
0000 X0112
XX16
XX16
XX16
XX16
XX16
XX16
Receive CRC Code Register 1
G1RCRC
Transmit CRC Code Register 1
G1TCRC
SI/O Extended Mode Register 1
SI/O Extended Receive Control Register 1
SI/O Special Communication Interrupt Detection Register 1
SI/O Extended Transmit Control Register 1
G1EMR
G1ERC
G1IRF
G1ETC
XX16
0016
X000 000X2
0016
0016
0016
0016
XXXX XXXX2
XX16
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 27 of 435
XX16
0016
0016
0016
0016
0016
0000 0XXX2
M32C/88 Group (M32C/88T)
Address
017016
017116
017216
017316
017416
017516
017616
017716
017816
017916
017A16
017B16
017C16
017D16
017E16
017F16
018016
018116
018216
018316
018416
018516
018616
018716
018816
018916
018A16
018B16
018C16
018D16
018E16
018F16
019016
019116
019216
019316
019416
019516
019616
019716
019816
019916
019A16
019B16
019C16
019D16
019E16
019F16
4. Special Function Registers (SFRs)
Register
CAN2 Slot Buffer Select Register
CAN2 Control Register 1
CAN2 Sleep Control Register
Symbol
C2SBS
C2CTLR1
C2SLPR
Value after RESET
0016(1)
X000 00XX2(1)
XXXX XXX02
CAN2 Acceptance Filter Support Register
C2AFS
0016(1)
0116(1)
Input Function Select Register
Input Function Select Register A
IPS
IPSA
0016
0016
CAN2 Message Slot Buffer 0 Standard ID0
CAN2 Message Slot Buffer 0 Standard ID1
CAN2 Message Slot Buffer 0 Extended ID0
CAN2 Message Slot Buffer 0 Extended ID1
CAN2 Message Slot Buffer 0 Extended ID2
CAN2 Message Slot Buffer 0 Data Length Code
CAN2 Message Slot Buffer 0 Data 0
CAN2 Message Slot Buffer 0 Data 1
CAN2 Message Slot Buffer 0 Data 2
CAN2 Message Slot Buffer 0 Data 3
CAN2 Message Slot Buffer 0 Data 4
CAN2 Message Slot Buffer 0 Data 5
CAN2 Message Slot Buffer 0 Data 6
CAN2 Message Slot Buffer 0 Data 7
CAN2 Message Slot Buffer 0 Time Stamp High-Order
CAN2 Message Slot Buffer 0 Time Stamp Low-Order
CAN2 Message Slot Buffer 1 Standard ID0
CAN2 Message Slot Buffer 1 Standard ID1
CAN2 Message Slot Buffer 1 Extended ID0
CAN2 Message Slot Buffer 1 Extended ID1
CAN2 Message Slot Buffer 1 Extended ID2
CAN2 Message Slot Buffer 1 Data Length Code
CAN2 Message Slot Buffer 1 Data 0
CAN2 Message Slot Buffer 1 Data 1
CAN2 Message Slot Buffer 1 Data 2
CAN2 Message Slot Buffer 1 Data 3
CAN2 Message Slot Buffer 1 Data 4
CAN2 Message Slot Buffer 1 Data 5
CAN2 Message Slot Buffer 1 Data 6
CAN2 Message Slot Buffer 1 Data 7
CAN2 Message Slot Buffer 1 Time Stamp High-Order
CAN2 Message Slot Buffer 1 Time Stamp Low-Order
C2SLOT0_0
C2SLOT0_1
C2SLOT0_2
C2SLOT0_3
C2SLOT0_4
C2SLOT0_5
C2SLOT0_6
C2SLOT0_7
C2SLOT0_8
C2SLOT0_9
C2SLOT0_10
C2SLOT0_11
C2SLOT0_12
C2SLOT0_13
C2SLOT0_14
C2SLOT0_15
C2SLOT1_0
C2SLOT1_1
C2SLOT1_2
C2SLOT1_3
C2SLOT1_4
C2SLOT1_5
C2SLOT1_6
C2SLOT1_7
C2SLOT1_8
C2SLOT1_9
C2SLOT1_10
C2SLOT1_11
C2SLOT1_12
C2SLOT1_13
C2SLOT1_14
C2SLOT1_15
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTE:
1. Values are obtained by setting the SLEEP bit in the C2SLPR register to "1" (sleep mode exited) after reset and
supplying a clock to the CAN module.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 28 of 435
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
Address
01A016
01A116
01A216
01A316
01A416
01A516
01A616
01A716
01A816
Register
Value after RESET
XX01 0X012(2)
CAN2 Control Register 0
C2CTLR0
XXXX 00002(2)
0000 00002(2)
CAN2 Status Register
C2STR
X000 0X012(2)
0016(2)
CAN2 Extended ID Register
C2IDR
0016(2)
0000 XXXX2(2)
CAN2 Configuration Register
C2CONR
0000 00002(2)
0016(2)
C2TSR
0016(2)
0016(2)
0016(2)
0016(2)
CAN2 Time Stamp Register
01A916
01AA16 CAN2 Transmit Error Count Register
01AB16 CAN2 Receive Error Count Register
01AC16
CAN2 Slot Interrupt Status Register
01AD16
01AE16
01AF16
01B016
CAN2 Slot Interrupt Mask Register
01B116
01B216
01B316
01B416
01B516
01B616
01B716
01B816
01B916
01BA16
01BB16
01BC16
01BD16
01BE16
01BF16
01C016
01C116
01C216
01C316
01C416
01C516
01C616
01C716
01C816
01C916
01CA16
01CB16
01CC16
01CD16
01CE16
01CF16
Symbol
C2TEC
C2REC
C2SISTR
0016(2)
0016(2)
C2SIMKR
0016(2)
CAN2 Error Interrupt Mask Register
CAN2 Error Interrupt Status Register
CAN2 Error Cause Register
CAN2 Baud Rate Prescaler
C2EIMKR
C2EISTR
C2EFR
C2BRP
XXXX X0002(2)
XXXX X0002(2)
0016(2)
0000 00012(2)
CAN2 Mode Register
C2MDR
XXXX XX002(2)
CAN2 Single Shot Control Register
C2SSCTLR
0016(2)
0016(2)
CAN2 Single Shot Status Register
C2SSSTR
0016(2)
0016(2)
(Note 1)
CAN2 Global Mask Register Standard ID0
CAN2 Global Mask Register Standard ID1
CAN2 Global Mask Register Extended ID0
CAN2 Global Mask Register Extended ID1
CAN2 Global Mask Register Extended ID2
C2GMR0
C2GMR1
C2GMR2
C2GMR3
C2GMR4
00002(2)
XXX0
XX00 00002(2)
XXXX 00002(2)
0016(2)
XX00 00002(2)
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTES:
1. The BANKSEL bit in the C2CTLR1 register switches functions for addresses 01C016 to 01DF16.
2. Values are obtained by setting the SLEEP bit in the C2SLPR register to "1" (sleep mode exited) after reset and
supplying a clock to the CAN module.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 29 of 435
M32C/88 Group (M32C/88T)
Address
4. Special Function Registers (SFRs)
Register
CAN2 Message Slot 0 Control Register /
Symbol
C2MCTL0/
Value after RESET
0000 00002(2)
CAN2 Local Mask Register A Standard ID0
CAN2 Message Slot 1 Control Register /
C2LMAR0
C2MCTL1/
XXX0 00002(2)
0000 00002(2)
CAN2 Local Mask Register A Standard ID1
CAN2 Message Slot 2 Control Register /
C2LMAR1
C2MCTL2/
XX00 00002(2)
0000 00002(2)
CAN2 Local Mask Register A Extended ID0
CAN2 Message Slot 3 Control Register /
C2LMAR2
C2MCTL3/
XXXX 00002(2)
0016(2)
CAN2 local Mask Register A Extended ID1
CAN2 Message Slot 4 Control Register /
C2LMAR3
C2MCTL4/
0016(2)
0000 00002(2)
CAN2 Local Mask Register A Extended ID2
CAN2 Message Slot 5 Control Register
CAN2 Message Slot 6 Control Register
CAN2 Message Slot 7 Control Register
CAN2 Message Slot 8 Control Register /
C2LMAR4
C2MCTL5
C2MCTL6
C2MCTL7
C2MCTL8/
XX00 00002(2)
0016(2)
0016(2)
0016(2)
0000 00002(2)
CAN2 Local Mask Register B Standard ID0
CAN2 Message Slot 9 Control Register /
C2LMBR0
C2MCTL9/
XXX0 00002(2)
0000 00002(2)
CAN2 Local Mask Register B Standard ID1
CAN2 Message Slot 10 Control Register /
C2LMBR1
C2MCTL10/
XX00 00002(2)
0000 00002(2)
CAN2 Local Mask Register B Extended ID2
CAN2 Message Slot 11 Control Register /
C2LMBR2
C2MCTL11/
XXXX 00002(2)
0016(2)
CAN2 Local Mask Register B Extended ID3
CAN2 Message Slot 12 Control Register /
C2LMBR3
C2MCTL12/
0016(2)
0000 00002(2)
CAN2 Local Mask Register B Extended ID4
01DD16 CAN2 Message Slot 13 Control Register
01DE16 CAN2 Message Slot 14 Control Register
01DF16 CAN2 Message Slot 15 Control Register
C2LMBR4
C2MCTL13
C2MCTL14
C2MCTL15
XX00 00002(2)
0016(2)
0016(2)
0016(2)
01D016
01D116
01D216
01D316
01D416
01D516
01D616
01D716
01D816
01D916
01DA16
01DB16
01DC16
(Note 1)
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTES:
1. The BANKSEL bit in the C2CTLR1 register switches functions for addresses 01C016 to 01DF16.
2. Values are obtained by setting the SLEEP bit in the C2SLPR register to "1" (sleep mode exited) after reset and
supplying a clock to the CAN module.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 30 of 435
M32C/88 Group (M32C/88T)
4. Special Function Registers (SFRs)
Address
01E016
01E116
01E216
01E316
01E416
01E516
01E616
01E716
01E816
01E916
01EA16
01EB16
01EC16
01ED16
01EE16
01EF16
01F016
01F116
Register
CAN0 Message Slot Buffer 0 Standard ID0
CAN0 Message Slot Buffer 0 Standard ID1
CAN0 Message Slot Buffer 0 Extended ID0
CAN0 Message Slot Buffer 0 Extended ID1
CAN0 Message Slot Buffer 0 Extended ID2
CAN0 Message Slot Buffer 0 Data Length Code
CAN0 Message Slot Buffer 0 Data 0
CAN0 Message Slot Buffer 0 Data 1
CAN0 Message Slot Buffer 0 Data 2
CAN0 Message Slot Buffer 0 Data 3
CAN0 Message Slot Buffer 0 Data 4
CAN0 Message Slot Buffer 0 Data 5
CAN0 Message Slot Buffer 0 Data 6
CAN0 Message Slot Buffer 0 Data 7
CAN0 Message Slot Buffer 0 Time Stamp High-Order
CAN0 Message Slot Buffer 0 Time Stamp Low-Order
CAN0 Message Slot Buffer 1 Standard ID0
CAN0 Message Slot Buffer 1 Standard ID1
Symbol
C0SLOT0_0
C0SLOT0_1
C0SLOT0_2
C0SLOT0_3
C0SLOT0_4
C0SLOT0_5
C0SLOT0_6
C0SLOT0_7
C0SLOT0_8
C0SLOT0_9
C0SLOT0_10
C0SLOT0_11
C0SLOT0_12
C0SLOT0_13
C0SLOT0_14
C0SLOT0_15
C0SLOT1_0
C0SLOT1_1
Value after RESET
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
01F216
01F316
01F416
01F516
01F616
01F716
01F816
01F916
01FA16
01FB16
01FC16
01FD16
01FE16
01FF16
020016
CAN0 Message Slot Buffer 1 Extended ID0
CAN0 Message Slot Buffer 1 Extended ID1
CAN0 Message Slot Buffer 1 Extended ID2
CAN0 Message Slot Buffer 1 Data Length Code
CAN0 Message Slot Buffer 1 Data 0
CAN0 Message Slot Buffer 1 Data 1
CAN0 Message Slot Buffer 1 Data 2
CAN0 Message Slot Buffer 1 Data 3
CAN0 Message Slot Buffer 1 Data 4
CAN0 Message Slot Buffer 1 Data 5
CAN0 Message Slot Buffer 1 Data 6
CAN0 Message Slot Buffer 1 Data 7
CAN0 Message Slot Buffer 1 Time Stamp High-Order
CAN0 Message Slot Buffer 1 Time Stamp Low-Order
C0SLOT1_2
C0SLOT1_3
C0SLOT1_4
C0SLOT1_5
C0SLOT1_6
C0SLOT1_7
C0SLOT1_8
C0SLOT1_9
C0SLOT1_10
C0SLOT1_11
C0SLOT1_12
C0SLOT1_13
C0SLOT1_14
C0SLOT1_15
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX01 0X012(1)
CAN0 Control Register 0
C0CTLR0
XXXX 00002(1)
0000 00002(1)
CAN0 Status Register
C0STR
X000 0X012(1)
0016(1)
CAN0 Extended ID Register
C0IDR
0016(1)
0000 XXXX2(1)
CAN0 Configuration Register
C0CONR
0000 00002(1)
0016(1)
CAN0 Time Stamp Register
C0TSR
CAN0 Transmit Error Count Register
CAN0 Receive Error Count Register
C0TEC
C0REC
0016(1)
0016(1)
0016(1)
0016(1)
CAN0 Slot Interrupt Status Register
C0SISTR
020116
020216
020316
020416
020516
020616
020716
020816
020916
020A16
020B16
020C16
020D16
020E16
020F16
0016(1)
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTE:
1. Values are obtained by setting the SLEEP bit in the C0SLPR register to "1" (sleep mode exited) after reset and
supplying a clock to the CAN module.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 31 of 435
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
Address
021016
021116
021216
021316
021416
021516
021616
021716
021816
021916
021A16
021B16
021C16
021D16
021E16
021F16
022016
022116
022216
022316
022416
022516
022616
022716
022816
022916
022A16
022B16
022C16
022D16
022E16
022F16
023016
023116
023216
023316
023416
023516
023616
023716
023816
023916
Register
Symbol
Value after RESET
0016(2)
CAN0 Slot Interrupt Mask Register
C0SIMKR
0016(2)
CAN0 Error Interrupt Mask Register
CAN0 Error Interrupt Status Register
CAN0 Error Cause Register
CAN0 Baud Rate Prescaler
C0EIMKR
C0EISTR
C0EFR
C0BRP
XXXX X0002(2)
XXXX X0002(2)
0016(2)
0000 00012(2)
CAN0 Mode Register
C0MDR
XXXX XX002(2)
CAN0 Single Shot Control Register
C0SSCTLR
0016(2)
0016(2)
CAN0 Single Shot Status Register
C0SSSTR
0016(2)
0016(2)
CAN0 Global Mask Register Standard ID0
CAN0 Global Mask Register Standard ID1
CAN0 Global Mask Register Extended ID0
CAN0 Global Mask Register Extended ID1
CAN0 Global Mask Register Extended ID2
C0GMR0
C0GMR1
C0GMR2
C0GMR3
C0GMR4
XXX0 00002(2)
XX00 00002(2)
XXXX 00002(2)
0016(2)
XX00 00002(2)
CAN0 Message Slot 0 Control Register /
C0MCTL0/
0000 00002(2)
(Note 1)
00002(2)
CAN0 Local Mask Register A Standard ID0
CAN0 Message Slot 1 Control Register /
C0LMAR0
C0MCTL1/
XXX0
0000 00002(2)
CAN0 Local Mask Register A Standard ID1
CAN0 Message Slot 2 Control Register /
C0LMAR1
C0MCTL2/
XX00 00002(2)
0000 00002(2)
CAN0 Local Mask Register A Extended ID0
CAN0 Message Slot 3 Control Register /
C0LMAR2
C0MCTL3/
XXXX 00002(2)
0016(2)
CAN0 local Mask Register A Extended ID1
CAN0 Message Slot 4 Control Register /
C0LMAR3
C0MCTL4/
0016(2)
0000 00002(2)
CAN0 Local Mask Register A Extended ID2
CAN0 Message Slot 5 Control Register
CAN0 Message Slot 6 Control Register
CAN0 Message Slot 7 Control Register
CAN0 Message Slot 8 Control Register /
C0LMAR4
C0MCTL5
C0MCTL6
C0MCTL7
C0MCTL8/
XX00 00002(2)
0016(2)
0016(2)
0016(2)
0000 00002(2)
CAN0 Local Mask Register B Standard ID0
CAN0 Message Slot 9 Control Register /
C0LMBR0
C0MCTL9/
XXX0 00002(2)
0000 00002(2)
CAN0 Local Mask Register B Standard ID1
C0LMBR1
XX00 00002(2)
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTES:
1. The BANKSEL bit in the C0CTLR1 register switches functions for addresses 022016 to 023F16.
2. Values are obtained by setting the SLEEP bit in the C0SLPR register to "1" (sleep mode exited) after reset and
supplying a clock to the CAN module.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 32 of 435
M32C/88 Group (M32C/88T)
Address
023A16
023B16
023C16
023D16
023E16
023F16
024016
024116
024216
024316
024416
024516
024616
024716
024816
024916
024A16
024B16
024C16
024D16
024E16
024F16
025016
025116
025216
025316
025416
025516
025616
025716
025816
025916
025A16
025B16
025C16
025D16
025E16
025F16
4. Special Function Registers (SFRs)
Register
CAN0 Message Slot 10 Control Register /
Symbol
C0MCTL10/
Value after RESET
0000 00002(2)
CAN0 Local Mask Register B Extended ID0
CAN0 Message Slot 11 Control Register /
C0LMBR2
C0MCTL11/
XXXX 00002(2)
0016(2)
CAN0 Local Mask Register B Extended ID1
CAN0 Message Slot 12 Control Register /
C0LMBR3
C0MCTL12/
0016(2)
0000 00002(2)
CAN0 Local Mask Register B Extended ID2
CAN0 Message Slot 13 Control Register
CAN0 Message Slot 14 Control Register
CAN0 Message Slot 15 Control Register
CAN0 Slot Buffer Select Register
CAN0 Control Register 1
CAN0 Sleep Control Register
C0LMBR4
C0MCTL13
C0MCTL14
C0MCTL15
C0SBS
C0CTLR1
C0SLPR
XX00 00002(2)
0016(2)
0016(2)
0016(2)
0016(2)
X000 00XX2(2)
XXXX XXX02
CAN0 Acceptance Filter Support Register
C0AFS
0016(2)
0116(2)
CAN1 Slot Buffer Select Register
CAN1 Control Register 1
CAN1 Sleep Control Register
C1SBS
C1CTLR1
C1SLPR
0016(3)
X000 00XX2(3)
XXXX XXX02(3)
CAN1 Acceptance Filter Support Register
C1AFS
0016(3)
0116(3)
(Note 1)
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTES:
1. The BANKSEL bit in the C0CTLR1 register switches functions for addresses 022016 to 023F16.
2. Values are obtained by setting the SLEEP bit in the C0SLPR register to "1" (sleep mode exited) after reset and
supplying a clock to the CAN module.
3. Values are obtained by setting the SLEEP bit in the C1SLPR register to "1" (sleep mode exited) after reset and
supplying a clock to the CAN module.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 33 of 435
M32C/88 Group (M32C/88T)
Address
026016
026116
026216
026316
026416
026516
026616
026716
026816
026916
026A16
026B16
026C16
026D16
026E16
026F16
027016
027116
027216
027316
027416
027516
027616
027716
027816
027916
027A16
027B16
027C16
027D16
027E16
027F16
028016
028116
028216
028316
028416
028516
028616
028716
028816
028916
028A16
028B16
028C16
028D16
028E16
028F16
4. Special Function Registers (SFRs)
Register
CAN1 Message Slot Buffer 0 Standard ID0
CAN1 Message Slot Buffer 0 Standard ID1
CAN1 Message Slot Buffer 0 Extended ID0
CAN1 Message Slot Buffer 0 Extended ID1
CAN1 Message Slot Buffer 0 Extended ID2
CAN1 Message Slot Buffer 0 Data Length Code
CAN1 Message Slot Buffer 0 Data 0
CAN1 Message Slot Buffer 0 Data 1
CAN1 Message Slot Buffer 0 Data 2
CAN1 Message Slot Buffer 0 Data 3
CAN1 Message Slot Buffer 0 Data 4
CAN1 Message Slot Buffer 0 Data 5
CAN1 Message Slot Buffer 0 Data 6
CAN1 Message Slot Buffer 0 Data 7
CAN1 Message Slot Buffer 0 Time Stamp High-Order
CAN1 Message Slot Buffer 0 Time Stamp Low-Order
CAN1 Message Slot Buffer 1 Standard ID0
CAN1 Message Slot Buffer 1 Standard ID1
CAN1 Message Slot Buffer 1 Extended ID0
CAN1 Message Slot Buffer 1 Extended ID1
CAN1 Message Slot Buffer 1 Extended ID2
CAN1 Message Slot Buffer 1 Data Length Code
CAN1 Message Slot Buffer 1 Data 0
CAN1 Message Slot Buffer 1 Data 1
CAN1 Message Slot Buffer 1 Data 2
CAN1 Message Slot Buffer 1 Data 3
CAN1 Message Slot Buffer 1 Data 4
CAN1 Message Slot Buffer 1 Data 5
CAN1 Message Slot Buffer 1 Data 6
CAN1 Message Slot Buffer 1 Data 7
CAN1 Message Slot Buffer 1 Time Stamp High-Order
CAN1 Message Slot Buffer 1 Time Stamp Low-Order
Symbol
C1SLOT0_0
C1SLOT0_1
C1SLOT0_2
C1SLOT0_3
C1SLOT0_4
C1SLOT0_5
C1SLOT0_6
C1SLOT0_7
C1SLOT0_8
C1SLOT0_9
C1SLOT0_10
C1SLOT0_11
C1SLOT0_12
C1SLOT0_13
C1SLOT0_14
C1SLOT0_15
C1SLOT1_0
C1SLOT1_1
C1SLOT1_2
C1SLOT1_3
C1SLOT1_4
C1SLOT1_5
C1SLOT1_6
C1SLOT1_7
C1SLOT1_8
C1SLOT1_9
C1SLOT1_10
C1SLOT1_11
C1SLOT1_12
C1SLOT1_13
C1SLOT1_14
C1SLOT1_15
Value after RESET
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX01 0X012(1)
CAN1 Control Register 0
C1CTLR0
XXXX 00002(1)
0000 00002(1)
CAN1 Status Register
C1STR
X000 0X012(1)
0016(1)
CAN1 Extended ID Register
C1IDR
0016(1)
0000 XXXX2(1)
CAN1 Configuration Register
C1CONR
0000 00002(1)
0016(1)
CAN1 Time Stamp Register
C1TSR
CAN1 Transmit Error Count Register
CAN1 Receive Error Count Register
C1TEC
C1REC
0016(1)
0016(1)
0016(1)
0016(1)
CAN1 Slot Interrupt Status Register
C1SISTR
0016(1)
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTE:
1. Values are obtained by setting the SLEEP bit in the C1SLPR register to "1" (sleep mode exited) after reset and
supplying the clock to the CAN module.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 34 of 435
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
Address
029016
029116
029216
029316
029416
029516
029616
029716
029816
029916
029A16
029B16
029C16
029D16
029E16
029F16
02A016
02A116
02A216
02A316
02A416
02A516
02A616
02A716
02A816
02A916
02AA16
02AB16
02AC16
02AD16
02AE16
02AF16
02B016
02B116
02B216
02B316
02B416
02B516
02B616
02B716
02B816
02B916
Register
Symbol
Value after RESET
0016(2)
CAN1 Slot Interrupt Mask Register
C1SIMKR
0016(2)
CAN1 Error Interrupt Mask Register
CAN1 Error Interrupt Status Register
CAN1 Error Factor Register
CAN1 Baud Rate Prescaler
C1EIMKR
C1EISTR
C1EFR
C1BRP
XXXX X0002(2)
XXXX X0002(2)
0016(2)
0000 00012(2)
CAN1 Mode Register
C1MDR
XXXX XX002(2)
CAN1 Single Shot Control Register
C1SSCTLR
0016(2)
0016(2)
CAN1 Single Shot Status Register
C1SSSTR
0016(2)
0016(2)
CAN1 Global Mask Register Standard ID0
CAN1 Global Mask Register Standard ID1
CAN1 Global Mask Register Extended ID0
CAN1 Global Mask Register Extended ID1
CAN1 Global Mask Register Extended ID2
C1GMR0
C1GMR1
C1GMR2
C1GMR3
C1GMR4
XXX0 00002(2)
XX00 00002(2)
XXXX 00002(2)
0016(2)
XX00 00002(2)
CAN1 Message Slot 0 Control Register /
C1MCTL0/
0000 00002(2)
(Note 1)
00002(2)
CAN1 Local Mask Register A Standard ID0
CAN1 Message Slot 1 Control Register /
C1LMAR0
C1MCTL1/
XXX0
0000 00002(2)
CAN1 Local Mask Register A Standard ID1
CAN1 Message Slot 2 Control Register /
C1LMAR1
C1MCTL2/
XX00 00002(2)
0000 00002(2)
CAN1 Local Mask Register A Extended ID0
CAN1 Message Slot 3 Control Register /
C1LMAR2
C1MCTL3/
XXXX 00002(2)
0016(2)
CAN1 Local Mask Register A Extended ID1
CAN1 Message Slot 4 Control Register /
C1LMAR3
C1MCTL4/
0016(2)
0000 00002(2)
CAN1 Local Mask Register A Extended ID2
CAN1 Message Slot 5 Control Register
CAN1 Message Slot 6 Control Register
CAN1 Message Slot 7 Control Register
CAN1 Message Slot 8 Control Register /
C1LMAR4
C1MCTL5
C1MCTL6
C1MCTL7
C1MCTL8/
XX00 00002(2)
0016(2)
0016(2)
0016(2)
0000 00002(2)
CAN1 Local Mask Register B Standard ID0
CAN1 Message Slot 9 Control Register /
C1LMBR0
C1MCTL9/
XXX0 00002(2)
0000 00002(2)
CAN1 Local Mask Register B Standard ID1
C1LMBR1
XX00 00002(2)
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTES:
1. The BANKSEL bit in the C1CTLR1 register switches functions for addresses 02A016 to 02BF16.
2. Values are obtained by setting the SLEEP bit in the C1SLPR register to "1" (sleep mode exited) after reset and
supplying a clock to the CAN module.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 35 of 435
M32C/88 Group (M32C/88T)
Address
4. Special Function Registers (SFRs)
Register
CAN1 Message Slot 10 Control Register /
Symbol
C1MCTL10/
Value after RESET
0000 00002(2)
CAN1 Local Mask Register B Extended ID0
CAN1 Message Slot 11 Control Register /
C1LMBR2
C1MCTL11/
XXXX 00002(2)
0016(2)
CAN1 Local Mask Register B Extended ID1
CAN1 Message Slot 12 Control Register /
C1LMBR3
C1MCTL12/
0016(2)
0000 00002(2)
CAN1 Local Mask Register B Extended ID2
02BD16 CAN1 Message Slot 13 Control Register
02BE16 CAN1 Message Slot 14 Control Register
02BF16 CAN1 Message Slot 15 Control Register
02C016
X0 Register Y0 Register
02C116
02C216
X1 Register Y1 Register
02C316
02C416
X2 Register Y2 Register
02C516
02C616
X3 Register Y3 Register
02C716
02C816
X4 Register Y4 Register
02C916
02CA16
X5 Register Y5 Register
02CB16
02CC16
X6 Register Y6 Register
02CD16
02CE16
X7 Register Y7 Register
02CF16
02D016
X8 Register Y8 Register
02D116
02D216
X9 Register Y9 Register
02D316
02D416
X10 Register Y10 Register
02D516
02D616
X11 Register Y11 Register
02D716
02D816
X12 Register Y12 Register
02D916
02DA16
X13 Register Y13 Register
02DB16
02DC16
X14 Register Y14 Register
02DD16
02DE16
X15 Register Y15 Register
02DF16
C1LMBR4
C1MCTL13
C1MCTL14
C1MCTL15
XX00 00002(2)
0016(2)
0016(2)
0016(2)
XX16
02BA16
02BB16
02BC16
X0R,Y0R
X1R,Y1R
X2R,Y2R
X3R,Y3R
X4R,Y4R
X5R,Y5R
X6R,Y6R
X7R,Y7R
X8R,Y8R
X9R,Y9R
X10R,Y10R
X11R,Y11R
X12R,Y12R
X13R,Y13R
X14R,Y14R
X15R,Y15R
(Note 1)
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTES:
1. The BANKSEL bit in the C1CTLR1 register switches functions for addresses 02A016 to 02BF16.
2. Values are obtained by setting the SLEEP bit in the C1SLPR register to "1" (sleep mode exited) after reset and
supplying a clock to the CAN module.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 36 of 435
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
Address
02E016
02E116
02E216
02E316
02E416
02E516
02E616
02E716
02E816
02E916
02EA16
X/Y Control Register
Register
Symbol
XYC
Value after RESET
XXXX XX002
UART1 Special Mode Register 4
UART1 Special Mode Register 3
UART1 Special Mode Register 2
UART1 Special Mode Register
UART1 Transmit/Receive Mode Register
UART1 Bit Rate Register
U1SMR4
U1SMR3
U1SMR2
U1SMR
U1MR
U1BRG
0016
0016
0016
0016
0016
XX16
XX16
UART1 Transmit Buffer Register
02EB16
02EC16 UART1 Transmit/Receive Control Register 0
02ED16 UART1 Transmit/Receive Control Register 1
02EE16
UART1 Receive Buffer Register
02EF16
02F016
02F116
02F216
02F316
02F416 UART4 Special Mode Register 4
02F516 UART4 Special Mode Register 3
02F616 UART4 Special Mode Register 2
02F716 UART4 Special Mode Register
02F816 UART4 Transmit/Receive Mode Register
02F916 UART4 Bit Rate Register
02FA16
UART4 Transmit Buffer Register
02FB16
02FC16 UART4 Transmit/Receive Control Register 0
02FD16 UART4 Transmit/Receive Control Register 1
02FE16
UART4 Receive Buffer Register
02FF16
030016 Timer B3, B4, B5 Count Start Flag
030116
030216
Timer A1-1 Register
030316
030416
Timer A2-1 Register
030516
030616
Timer A4-1 Register
030716
030816 Three-Phase PWM Control Register 0
030916 Three-Phase PWM Control Register 1
030A16 Three-Phase Output Buffer Register 0
030B16 Three-Phase Output Buffer Register 1
030C16 Dead Time Timer
030D16 Timer B2 Interrupt Generation Frequency Set Counter
030E16
030F16
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 37 of 435
U1TB
U1C0
U1C1
U1RB
U4SMR4
U4SMR3
U4SMR2
U4SMR
U4MR
U4BRG
U4TB
U4C0
U4C1
U4RB
TBSR
XX16
0000 10002
0000 00102
XX16
XX16
0016
0016
0016
0016
0016
XX16
XX16
XX16
0000 10002
0000 00102
XX16
XX16
000X XXXX2
XX16
TA11
TA21
TA41
INVC0
INVC1
IDB0
IDB1
DTT
ICTB2
XX16
XX16
XX16
XX16
XX16
0016
0016
XX11 11112
XX11 11112
XX16
XX16
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
Address
031016
031116
031216
031316
031416
031516
031616
031716
031816
031916
031A16
031B16
031C16
031D16
031E16
031F16
032016
032116
032216
032316
032416
032516
032616
032716
032816
032916
032A16
032B16
032C16
032D16
032E16
032F16
033016
033116
033216
033316
033416
033516
033616
033716
033816
033916
033A16
033B16
033C16
033D16
033E16
033F16
Register
Symbol
Value after RESET
XX16
Timer B3 Register
TB3
Timer B4 Register
TB4
Timer B5 Register
TB5
Timer B3 Mode Register
Timer B4 Mode Register
Timer B5 Mode Register
TB3MR
TB4MR
TB5MR
00XX 00002
00XX 00002
00XX 00002
External Interrupt Request Source Select Register
IFSR
0016
UART3 Special Mode Register 4
UART3 Special Mode Register 3
UART3 Special Mode Register 2
UART3 Special Mode Register
UART3 Transmit/Receive Mode Register
UART3 Bit Rate Register
U3SMR4
U3SMR3
U3SMR2
U3SMR
U3MR
U3BRG
UART3 Transmit Buffer Register
U3TB
UART3 Transmit/Receive Control Register 0
UART3 Transmit/Receive Control Register 1
U3C0
U3C1
UART3 Receive Buffer Register
U3RB
0016
0016
0016
0016
0016
XX16
XX16
XX16
0000 10002
0000 00102
XX16
XX16
UART2 Special Mode Register 4
UART2 Special Mode Register 3
UART2 Special Mode Register 2
UART2 Special Mode Register
UART2 Transmit/Receive Mode Register
UART2 Bit Rate Register
U2SMR4
U2SMR3
U2SMR2
U2SMR
U2MR
U2BRG
UART2 Transmit Buffer Register
U2TB
UART2 Transmit/Receive Control Register 0
UART2 Transmit/Receive Control Register 1
U2C0
U2C1
UART2 Receive Buffer Register
U2RB
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 38 of 435
XX16
XX16
XX16
XX16
XX16
0016
0016
0016
0016
0016
XX16
XX16
XX16
0000 10002
0000 00102
XX16
XX16
M32C/88 Group (M32C/88T)
Address
034016
034116
034216
034316
034416
034516
034616
034716
034816
034916
034A16
034B16
034C16
034D16
034E16
034F16
035016
035116
035216
035316
035416
035516
035616
035716
035816
035916
035A16
035B16
035C16
035D16
035E16
035F16
036016
036116
036216
036316
036416
036516
036616
036716
036816
036916
036A16
036B16
036C16
036D16
036E16
036F16
4. Special Function Registers (SFRs)
Register
Count Start Flag
Clock Prescaler Reset Flag
One-Shot Start Flag
Trigger Select Register
Up/Down Flag
Symbol
TABSR
CPSRF
ONSF
TRGSR
UDF
Timer A0 Register
TA0
Timer A1 Register
TA1
Timer A2 Register
TA2
Timer A3 Register
TA3
Timer A4 Register
TA4
Timer B0 Register
TB0
Timer B1 Register
TB1
Timer B2 Register
TB2
Timer A0 Mode Register
Timer A1 Mode Register
Timer A2 Mode Register
Timer A3 Mode Register
Timer A4 Mode Register
Timer B0 Mode Register
Timer B1 Mode Register
Timer B2 Mode Register
Timer B2 Special Mode Register
Count Source Prescaler Register(1)
TA0MR
TA1MR
TA2MR
TA3MR
TA4MR
TB0MR
TB1MR
TB2MR
TB2SC
TCSPR
UART0 Special Mode Register 4
UART0 Special Mode Register 3
UART0 Special Mode Register 2
UART0 Special Mode Register
UART0 Transmit/Receive Mode Register
UART0 Bit Rate Register
U0SMR4
U0SMR3
U0SMR2
U0SMR
U0MR
U0BRG
UART0 Transmit Buffer Register
U0TB
UART0 Transmit/Receive Control Register 0
UART0 Transmit/Receive Control Register 1
U0C0
U0C1
UART0 Receive Buffer Register
U0RB
Value after RESET
0016
0XXX XXXX2
0016
0016
0016
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
0016
0016
0016
0016
0016
00XX 00002
00XX 00002
00XX 00002
XXXX XXX02
0XXX 00002
0016
0016
0016
0016
0016
XX16
XX16
XX16
0000 10002
0000 00102
XX16
XX16
X: Indeterminate
Blank spaces are reserved. No access is allowed.
NOTE:
1. The TCSPR register maintains values set before reset, even after software reset or watchdog timer reset has
been performed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 39 of 435
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
Address
037016
037116
037216
037316
037416
037516
037616
037716
037816
037916
037A16
037B16
037C16
037D16
037E16
037F16
038016
038116
038216
038316
038416
038516
038616
038716
038816
038916
038A16
038B16
038C16
038D16
038E16
038F16
039016
039116
039216
039316
039416
039516
039616
039716
039816
039916
039A16
039B16
039C16
039D16
039E16
039F16
Register
Symbol
Value after RESET
DMA0 Request Source Select Register
DMA1 Request Source Select Register
DMA2 Request Source Select Register
DMA3 Request Source Select Register
DM0SL
DM1SL
DM2SL
DM3SL
CRC Data Register
CRCD
CRC Input Register
CRCIN
A/D0 Register 0
AD00
A/D0 Register 1
AD01
A/D0 Register 2
AD02
A/D0 Register 3
AD03
A/D0 Register 4
AD04
A/D0 Register 5
AD05
A/D0 Register 6
AD06
A/D0 Register 7
AD07
A/D0 Control Register 4
AD0CON4
XXXX 00XX2
A/D0 Control Register 2
A/D0 Control Register 3
A/D0 Control Register 0
A/D0 Control Register 1
D/A Register 0
AD0CON2
AD0CON3
AD0CON0
AD0CON1
DA0
XX0X X0002
XXXX X0002
0016
0016
XX16
D/A Register 1
DA1
XX16
D/A Control Register
DACON
XXXX XX002
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 40 of 435
0X00 00002
0X00 00002
0X00 00002
0X00 00002
XX16
XX16
XX16
XXXX XXXX2
0000 00002
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
XX16
M32C/88 Group (M32C/88T)
4. Special Function Registers (SFRs)
<144-pin package>
Address
03A016
03A116
03A216
03A316
03A416
03A516
03A616
03A716
03A816
03A916
03AA16
03AB16
03AC16
03AD16
03AE16
03AF16
03B016
03B116
03B216
Register
Function Select Register A8
Function Select Register A9
Symbol
PS8
PS9
Value after RESET
X000 00002
0016
Function Select Register D1
PSD1
X0XX XX002
Function Select Register C2
Function Select Register C3
PSC2
PSC3
XXXX X00X2
X0XX XXXX2
Function Select Register C
Function Select Register A0
Function Select Register A1
Function Select Register B0
PSC
PS0
PS1
PSL0
00X0 00002
0016
0016
0016
03B316
03B416
03B516
03B616
03B716
03B816
03B916
03BA16
03BB16
03BC16
03BD16
03BE16
03BF16
03C016
03C116
03C216
03C316
03C416
03C516
03C616
03C716
03C816
03C916
03CA16
03CB16
03CC16
03CD16
03CE16
03CF16
Function Select Register B1
Function Select Register A2
Function Select Register A3
Function Select Register B2
Function Select Register B3
PSL1
PS2
PS3
PSL2
PSL3
0016
00X0 00002
0016
00X0 00002
0016
Function Select Register A5
PS5
XXX0 00002
Port P6 Register
Port P7 Register
Port P6 Direction Register
Port P7 Direction Register
Port P8 Register
Port P9 Register
Port P8 Direction Register
Port P9 Direction Register
Port P10 Register
Port P11 Register
Port P10 Direction Register
Port P11 Direction Register
Port P12 Register
Port P13 Register
Port P12 Direction Register
Port P13 Direction Register
P6
P7
PD6
PD7
P8
P9
PD8
PD9
P10
P11
PD10
PD11
P12
P13
PD12
PD13
XX16
XX16
0016
0016
XX16
XX16
00X0 00002
0016
XX16
XX16
0016
XXX0 00002
XX16
XX16
0016
0016
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 41 of 435
M32C/88 Group (M32C/88T)
4. Special Function Registers (SFRs)
<144-pin package>
Address
03D016
03D116
03D216
03D316
03D416
03D516
03D616
03D716
03D816
03D916
03DA16
03DB16
03DC16
03DD16
03DE16
03DF16
03E016
03E116
03E216
03E316
03E416
03E516
03E616
03E716
03E816
03E916
03EA16
03EB16
03EC16
03ED16
03EE16
03EF16
03F016
03F116
03F216
03F316
03F416
03F516
03F616
03F716
03F816
03F916
03FA16
03FB16
03FC16
03FD16
03FE16
03FF16
Register
Port P14 Register
Port P15 Register
Port P14 Direction Register
Port P15 Direction Register
Symbol
P14
P15
PD14
PD15
Value after RESET
XX16
XX16
X000 00002
0016
Pull-Up Control Register 2
Pull-Up Control Register 3
Pull-Up Control Register 4
PUR2
PUR3
PUR4
0016
0016
XXXX 00002
Port P0 Register
Port P1 Register
Port P0 Direction Register
Port P1 Direction Register
Port P2 Register
Port P3 Register
Port P2 Direction Register
Port P3 Direction Register
Port P4 Register
Port P5 Register
Port P4 Direction Register
Port P5 Direction Register
P0
P1
PD0
PD1
P2
P3
PD2
PD3
P4
P5
PD4
PD5
XX16
XX16
0016
0016
XX16
XX16
0016
0016
XX16
XX16
0016
0016
Pull-Up Control Register 0
Pull-Up Control Register 1
PUR0
PUR1
0016
XXXX 00002
Port Control Register
PCR
XXXX XXX02
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 42 of 435
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
<100-pin package>
Address
03A016
03A116
03A216
03A316
03A416
03A516
03A616
03A716
03A816
03A916
03AA16
03AB16
03AC16
03AD16
03AE16
03AF16
03B016
03B116
03B216
03B316
03B416
03B516
03B616
03B716
03B816
03B916
03BA16
03BB16
03BC16
03BD16
03BE16
03BF16
03C016
03C116
03C216
03C316
03C416
03C516
03C616
03C716
03C816
03C916
03CA16
03CB16
03CC16
03CD16
03CE16
03CF16
Register
Symbol
Value after RESET
Function Select Register D1
PSD1
X0XX XX002
Function Select Register C2
Function Select Register C3
PSC2
PSC3
XXXX X00X2
X0XX XXXX2
Function Select Register C
Function Select Register A0
Function Select Register A1
Function Select Register B0
Function Select Register B1
Function Select Register A2
Function Select Register A3
Function Select Register B2
Function Select Register B3
PSC
PS0
PS1
PSL0
PSL1
PS2
PS3
PSL2
PSL3
00X0 00002
0016
0016
0016
0016
00X0 00002
0016
00X0 00002
0016
Port P6 Register
Port P7 Register
Port P6 Direction Register
Port P7 Direction Register
Port P8 Register
Port P9 Register
Port P8 Direction Register
Port P9 Direction Register
Port P10 Register
P6
P7
PD6
PD7
P8
P9
PD8
PD9
P10
XX16
XX16
0016
0016
XX16
XX16
00X0 00002
0016
XX16
Port P10 Direction Register
Set default value to "FF16"
PD10
0016
Set default value to "FF16"
Set default value to "FF16"
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 43 of 435
4. Special Function Registers (SFRs)
M32C/88 Group (M32C/88T)
<100-pin package>
Address
03D016
03D116
03D216
03D316
03D416
03D516
03D616
03D716
03D816
03D916
03DA16
03DB16
03DC16
03DD16
03DE16
03DF16
03E016
03E116
03E216
03E316
03E416
03E516
03E616
03E716
03E816
03E916
03EA16
03EB16
03EC16
03ED16
03EE16
03EF16
03F016
03F116
03F216
03F316
03F416
03F516
03F616
03F716
03F816
03F916
03FA16
03FB16
03FC16
03FD16
03FE16
03FF16
Register
Symbol
Value after RESET
Set default value to "FF16"
Set default value to "FF16"
Pull-Up Control Register 2
Pull-Up Control Register 3
Set default value to "0016"
PUR2
PUR3
0016
0016
Port P0 Register
Port P1 Register
Port P0 Direction Register
Port P1 Direction Register
Port P2 Register
Port P3 Register
Port P2 Direction Register
Port P3 Direction Register
Port P4 Register
Port P5 Register
Port P4 Direction Register
Port P5 Direction Register
P0
P1
PD0
PD1
P2
P3
PD2
PD3
P4
P5
PD4
PD5
XX16
XX16
0016
0016
XX16
XX16
0016
0016
XX16
XX16
0016
0016
Pull-up Control Register 0
Pull-up Control Register 1
PUR0
PUR1
0016
XXXX 00002
Port Control Register
PCR
XXXX XXX02
X: Indeterminate
Blank spaces are reserved. No access is allowed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 44 of 435
5. Reset
M32C/88 Group (M32C/88T)
5. Reset
Hardware reset 1, software reset, and watchdog timer reset are available to reset the microcomputer.
5.1 Hardware Reset 1
____________
Pins, the CPU and SFRs are reset by setting the RESET pin. If the supply voltage meets the recommended
operating conditions, all pins are reset and become input ports(1) when a low-level ("L") signal is applied to
___________
the RESET pin. The oscillation circuit is also reset and the main clock starts oscillating. The CPU and SFRs
____________
are reset when a signal applied to the RESET pin changes "L" to high ("H"). The microcomputer executes
the program in an address indicated by the reset vector. The internal RAM is not reset. When an "L" signal
____________
is applied to the RESET pin while writing data to the internal RAM, the internal RAM is in an indeterminate
state.
Figure 5.1 shows an example of the reset circuit. Figure 5.2 shows a reset sequence.
NOTE:
1. Whether ports are pulled up or not is indeterminate until intenal supply voltage stabilizes.
5.1.1 Reset on a Stable Supply Voltage
____________
(1) Apply an "L" signal to the RESET pin
(2) Provide 20 or more clock cycle inputs into the XIN pin
____________
(3) Apply an "H" signal to the RESET pin
5.1.2 Power-on Reset
____________
(1) Apply an "L" signal to the RESET pin
(2) Raise the supply voltage to the recommended operating level
(3) Wait for td(P-R) ms to allow the internal voltage to stabilize
(4) Provide 20 or more clock cycle inputs into the XIN pin
____________
(5) Apply an "H" signal to the RESET pin
Recommended
operating voltage
VCC
0V
VCC
RESET
RESET
0.2VCC
or below
0.2VCC or below
0V
td(P-R) + 20 or more clock cycle
input into the XIN pin
Figure 5.1 Reset Circuit
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 45 of 435
5. Reset
M32C/88 Group (M32C/88T)
VCC
XIN
XIN
td(P-R) ms or more
is required
20 or more cycles
are required
RESET
168 to 173 BCLK cycles
BCLK
Single-Chip Mode
FFFFFC16
Content of reset vector
Address
FFFFFE16
Figure 5.2 Reset Sequence
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 46 of 435
5. Reset
M32C/88 Group (M32C/88T)
5.2 Software Reset
Pins, the CPU and SFRs are reset when the PM03 bit in the PM0 register is set to "1" (microcomputer
reset). Then the microcomputer executes the program in an address determined by the reset vector.
Set the PM03 bit to "1" while the main clock is selected as the CPU clock and the main clock oscillation is
stable.
In the software reset, the microcomputer does not reset a part of SFRs. Refer to 4. Special Function
Registers (SFRs) for details. Processor mode remains unchanged since the PM01 and PM00 bits in the
PM0 register are not reset.
5.3 Watchdog Timer Reset
Pins, the CPU and SFRs are reset when the CM06 bit in the CM0 register is set to "1" (reset) and the
watchdog timer underflows. Then the microcomputer executes the program in an address determined by
the reset vector.
In the watchdog timer reset, the microcomputer does not reset a part of SFRs. Refer to 4. Special Function
Registers (SFRs) for details. Processor mode remains unchanged since the PM01 and PM00 bits in the
PM0 register are not reset.
5.4 Internal Space
Figure 5.3 shows CPU register states after reset. Refer to 4. Special Function Registers (SFRs) for SFR
states after reset.
0 : "0" after reset
X : Indeterminate after reset
General Registers
High-speed Interrupt Registers
b15
b15
b0
Flag Register (FLG)
b15
b8 b7
b0
X 0 0 0 X X X X 0 0 0 0 0 0 0 0
IPL
U I O B S Z D C
b0
XXXX16
b23
Flag Save Register (SVF)
XXXXXX16
PC Save Register (SVP)
XXXXXX16
Vector Register (VCT)
DMAC-associated Registers
b0
b7
0016
0016
Data Register (R0H/R0L)
0016
0016
Data Register (R1H/R1L)
b15
b0
0016
DMA Mode Register (DMD0)
0016
DMA Mode Register (DMD1)
000016
Data Register (R2)
XXXX16
DMA Transfer Count Register (DCT0)
000016
Data Register (R3)
XXXX16
DMA Transfer Count Register (DCT1)
00000016
Address Register (A0)
XXXX16
DMA Transfer Count Reload Register (DRC0)
00000016
Address Register (A1)
XXXX16
DMA Transfer Count Reload Register (DRC1)
00000016
Static Base Register (SB)
XXXXXX16
DMA Memory Address Register (DMA0)
00000016
Frame Base Register (FB)
XXXXXX16
DMA Memory Address Register (DMA1)
XXXXXX16
DMA Memory Address Reload Register (DRA0)
XXXXXX16
DMA Memory Address Reload Register (DRA1)
XXXXXX16
DMA SFR Address Register (DSA0)
XXXXXX16
DMA SFR Address Register (DSA1)
b23
00000016
User Stack Pointer (USP)
00000016
Interrupt Stack Pointer (ISP)
00000016
Contents of addresses
Interrupt Table Register (INTB)
Program Counter (PC)
FFFFFE16 to FFFFFC16
Figure 5.3 CPU Register States after Reset
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 47 of 435
b23
6. Cold Start-up/Warm Start-up Determine Function
M32C/88 Group (M32C/88T)
6. Cold Start-up/Warm Start-up Determine Function
The WDC5 bit in the WDC register determines either cold start-up, power-on reset, or warm start-up, reset
during the microcomputer running. Default value of the WDC5 bit is "0" (cold start-up) when power-on. It is
set to "1" (warm start-up) by writing desired values to the WDC register. The WDC5 bit is not reset,
regardless of a software reset or reset signal input.
Figure 6.1 shows the WDC registser. Figure 6.2 shows a block diagram of the cold start-up/warm start-up
determine function. Figure 6.3 shows its operation exmaple.
Watchdog Timer Control Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
WDC
0
Bit
Symbol
(b4 - b0)
WDC5
(b6)
WDC7
Address
000F16
After Reset
000X XXXX2
Bit Name
Function
High-Order Bit of the Watchdog Timer
Cold Start-up/
Warm Start-up
Determine Flag(1,2, 3)
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 48 of 435
RO
0: Cold start-up
1: Warm start-up
RW
Reserved Bit
Set to "0"
RW
Prescaler Select Bit
0: Divide-by-16
1: Divide-by-128
RW
NOTES:
1. The WDC5 bit remains set to "1", regardless of setting to "1" or "0".
2. The WDC5 bit is set to "0" when power is turned on and can be set to "1" by program only.
3. The WDC5 bit maintains a value set before reset, even after reset has been performed.
Figure 6.1 WDC Register
RW
6. Cold Start-up/Warm Start-up Determine Function
M32C/88 Group (M32C/88T)
WDC5 Bit
Write to WDC register
S
Q
COLD/WARM
(Cold Start-up/Warm Start-up)
Hardware Reset 1 when Power-on
R
Figure 6.2 Cold Start-up/Warm Start-up Determine Function Block Diagram
5V
VCC
0V
5V
Pch transistor ON (Approx. 4V)
CPU reset release
RESET
0V
T1
"1"
Set to "1" by program
T2
T > 100µs
WDC5 Bit
"0"
Program running started
No change
even if the
voltage applied
to RESET is 0V.
Reset Sequence (Approx. 20µs @16MHz)
NOTE:
1. Time difference between T1 and T2 may affect the WDC5 bit setting period.
Figure 6.3 Cold Start-up/Warm Start-up Determine Function Operation
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 49 of 435
The WDC5 bit is set to "0"
as soon as enough voltage
is applied to VCC.
M32C/88 Group (M32C/88T)
7. Processor Mode
7. Processor Mode
NOTE
Use M32C/88T in single-chip mode only.
M32C/88T cannot be used in memory expansion mode and microprocessor mode.
7.1 Types of Processor Mode
Only single-chip mode can be selected as a processor mode. SFRs, internal RAM, and internal ROM can
be accessed. All pins are assigned to input/output ports or peripheral function input/output ports.
7.2 Setting of Processor Mode
The CNVSS pin and the PM01 and PM00 bits in the PM0 register determine which processor mode is
selected. Apply an low-level ("L") signal to the CNVSS pin. Set the PM01 and PM00 bits to "002" (singlechip mode).
Figures 7.1 and 7.2 show the PM0 register and PM1 register. Figure 7.3 shows a memory map in singlechip mode.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 50 of 435
7. Processor Mode
M32C/88 Group (M32C/88T)
Processor Mode Register 0(1)
b7
b6
b5
b4
b3
b2
b1
0
b0
Symbol
PM0
Bit
Symbol
Address
000416
After Reset
1000 00002 (CNVss = "L")
0000 00112 (CNVss = "H")
Bit Name
Function
RW
b1 b0
PM00
PM01
0 0: Single-chip mode
(8)
Processor Mode Bit(2, 3) 0 1: Memory expansion mode
1 0: Do not set to this value
1 1: Microprocessor mode(8)
RW
RW
PM02
R/W Mode Select Bit
0: RD / BHE / WR
1: RD / WRH / WRL
RW
PM03
Software Reset Bit
The microcomputer is reset when
this bit is set to "1". When read, its
content is "0".
RW
b5 b4
Multiplexed Bus Space
Select Bit(4)
0 0: Multiplexed bus is not used
RW
0 1: Access the CS2 area using the bus
0 1: Access the CS1 area using the bus
1 1: Access all CS areas using the bus(5) RW
Reserved Bit
Set to "0"
PM04
PM05
(b6)
PM07
BCLK Output
Disable Bit(6)
RW
0: BCLK is output(7)
1: BCLK is not output
RW
The CM01 and CM00 bits in the
CM0 register determine pin functions
NOTES:
1. Rewrite the PM0 register after the PRC1 bit in the PRCR register is set to "1"(write enabled).
2. The PM01 and PM00 bits maintain values set before reset, even after software reset or watchdog
timer reset has performed.
3. Set the PM01 and PM00 bits to "012" or "112" separately. Rewrite other bits before rewriting the
PM01 and PM00 bits.
4. The PM04 and PM05 bits are available in memory expansion mode or microprocessor mode.
• Set the PM05 and PM04 bits to "002" in mode 0.
• Do not set the PM05 and PM04 bits to "012" in mode 2.
5. The PM05 and PM04 bits cannot be set to "112" in microprocessor mode since the microcomputer
starts up with the separate bus after reset.
When the PM05 and PM04 bits are set to "112" in memory expansion mode, the microcomputer can
access each 64-Kbyte chip-select-assigned address space. The multiplexed bus is not available in
mode 0. The microcomputer accesses the CS0 to CS2 in mode 1, CS0 and CS1 in mode 2 and
CS0 to CS3 in mode 3.
6. No BCLK is output in single-chip mode even if the PM07 bit is set to "0". When a clock output is
terminated in microprocessor mode or memory expansion mode, set the PM07 bit to "1" and the
CM01 and CM00 bits in the CM0 register to "002" (I/O port P53). P53 outputs "L".
7. When the PM07 bit is set to "0" (BCLK output), set the CM01 and CM00 bits to "002".
8. M32C/88T cannot be used in memory expansion mode and microprocessor mode.
Figure 7.1 PM0 Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 51 of 435
7. Processor Mode
M32C/88 Group (M32C/88T)
Processor Mode Register 1(1)
b7
b6
0
0
b5
b4
b3
b2
b1
Symbol
PM1
b0
Bit
Symbol
After Reset
0016
Address
000516
Bit Name
Function
RW
b1 b0
PM10
PM11
0 0: Mode 0 (A20 to A23 for P44 to P47)
RW
0 1: Mode 1 (A20 for P44,
CS2
to
CS0
for
P4
5 to P47)
External Memory Space
1 0: Mode 2 (A20, A21 for P44, P45,
Mode Bit(2, 4)
CS1, CS0 for P46, P47)
RW
1 1: Mode 3
(CS3 to CS0 for P44 to P47)
PM12
Internal Memory
Wait Bit
0: No wait state
1: Wait state
RW
PM13
SFR Area Wait Bit
0: 1 wait state
1: 2 Wait states
RW
b5 b4
PM14
ALE Pin Select Bit(2, 4)
PM15
Reserved Bit
(b7-b6)
0 0: No ALE
0 1: P53/BCLK(3)
1 0: P56
1 1: P54/HLDA
RW
Set to "0"
RW
RW
NOTES:
1. Rewrite the PM1 register after the PRC1 bit in the PRCR register is set to "1" (write enabled).
2. The PM15 and PM14 bit setting, PM11 and PM10 bit setting are available in memory expansion
mode or microprocessor mode.
3. Set the CM01 and CM00 bits in the CM0 register to "002" (I/O port P53) when the PM15 and PM14
bits are set to "012" (P53/BCLK select).
4. M32C/88T cannot be used in memory expansion mode and microprocessor mode.
Figure 7.2 PM1 Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 52 of 435
7. Processor Mode
M32C/88 Group (M32C/88T)
Single-chip Mode
00000016
00040016
SFRs
Internal RAM
Reserved Space
00F00016
01000016
Block A(1)
Not Used
F F F F F F 16
Internal ROM
NOTE:
1. Additional 4-Kbyte space is provided in the flash memory version for storing data.
Figure 7.3 Memory Map in Single-chip Mode
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 53 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
8. Clock Generation Circuit
8.1 Types of the Clock Generation Circuit
Four circuits are included to generate the system clock signal:
• Main clock oscillation circuit
• Sub clock oscillation circuit
• On-chip oscillator
• PLL frequency synthesizer
Table 8.1 lists specifications of the clock generation circuit. Figure 8.1 shows a block diagram of the clock
generation circuit. Figures 8.2 to 8.8 show registers controlling the clock.
Table 8.1 Clock Generation Circuit Specification
Item
Main Clock
Oscillation Circuit
Sub Clock
Oscillation Circuit
PLL Frequency
Synthesizer
On-chip Oscillator
Use
CPU clock source,
Peripheral function
clock source
CPU clock source,
Timer A and B clock
source
CPU clock source,
Peripheral function
clock source
CPU clock source,
Peripheral function
clock source
Clock Frequency
Up to 32 MHz
32.768 kHz
Approx. 1 MHz
Up to 32 MHz
(See Table 8.3)
Connectable
Osillator or
Additional Circuit
Ceramic resonator
Crystal oscillator
Crystal oscillator
---
---
Pins for Oscillator
or for Additional
Circuit
XIN, XOUT
XCIN, XCOUT
---
---
Oscillation Stop/
Restart Function
Available
Available
Available
Available
Oscillator State
after Reset
Oscillating
Stopped
Stopped
Stopped
Externally generated
clock can be applied.
Externally generated
clock can be applied.
When the main clock
stops oscillating, the
on-chip oscillator
starts oscillating automatically and
becomes clock source
for the CPU and
peripheral function.
---
Other
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 54 of 435
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Figure 8.1 Clock Generation Circuit
Page 55 of 435
CLKOUT
CM10=1 (Stop Mode)
Output signal to determine
interrupt priority request level
NMI
RESET
Software Reset
WAIT Instruction (Wait Mode)
CM01 and CM00
11
10
01
PM21
CM21
PM21
PM22
Clock Edge Detect
/Charge and
Discharge
Circuit Control
Charge and
Discharge
Circuit
CM04
CM05
On-Chip Oscillator
Watchdog Timer
Interrupt Request
Circuit to Generate
Oscillation Stop
Detection Interrupt
Request
On-Chip Oscillator and Main Clock Stop Detection
a
S Q
R
S Q
R
CM02
CM10
CM20
PM26
XIN
XCIN
XCOUT
b
CM21 Switch
Signal
On-chip Oscillator
Clock f(ROC)
Interrupt
Request Signal
1
b
CM17
0
CM21
Phase
Comparator
PLC12: Bit in the PLC1 register
Reference
Frequency Counter
Programmable
Counter
PLL Frequency Synthesizer
c
1
0
fC
0
CM07
fC32
1
Divider
Reset
CPSR=1
1/32
1/2
1/2
1/2
CST
PM24
1
0
PM27 to PM26
1/m
10
01
00
1/2
(Note 2)
fROC
XIN Clock
fROC
CM21
1/2n
1/2
fAD
Peripheral
Function
Clock
Peripheral Function Clock
BCLK
CPU Clock
fCAN
f2n(1)
f32
f8
f1
Charge
Pump
Voltage
Controlled
Oscillator
(VCO)
1/3
1/2
PLC12
PLL Clock
e
NOTES:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
2. The MCD4 to MCD0 bits in the MCD register select divide-by-m (m=1,2,3,4,6,8,10,12,14,16 ).
Sub Clock
CM21
CM05
XIN Clock
Main Clock
On-chip
Oscillator
0scillating
Activated
Main Clock
Stop Detect
Detecting
Function
Activated
c PLL Frequency e
Synthesizer
a
Sub Clock Oscillation Circuit
XOUT
Main Clock Oscillation Circuit
PM21
CM00, CM01, CM02, CM04, CM05, CM07: Bits in the CM0 register PM21, PM22, PM24, PM26, PM27: Bits in the PM2 register
CM10, CM17: Bits in the CM1 register
CST: Bit in the TCSPR register
CM20, CM21: Bits in the CM2 register
CPSR: Bit in the CPSRF register
fC
f8
f32
Pheripheral Function
Clock
Port P53 00
Wait Mode
CM02
PM27
PM26
Wait Mode
CM02
M32C/88 Group (M32C/88T)
8. Clock Generation Circuit
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
System Clock Control Register 0(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
CM0
Bit
Symbol
Address
000616
After Reset
0000 10002
Bit Name
Function
b1 b0
CM00
Clock Output Function
Select Bit(2)
CM01
0 0: I/O port P53
0 1: Outputs fC
1 0: Outputs f8
1 1: Outputs f32
RW
RW
RW
CM02
0: Peripheral clock does not stop in
In Wait Mode, Peripheral
wait mode
Function Clock Stop Bit(9) 1: Peripheral clock stops in wait
mode(3)
RW
CM03
XCIN-XCOUT Drive
Capacity Select Bit(11)
0: Low
1: High
RW
CM04
Port XC Switch Bit
0: I/O port function
1: XCIN-XCOUT oscillation function(4)
RW
CM05
Main Clock (XIN-XOUT)
Stop Bit(5, 9)
0: Main clock oscillates
1: Main clock stops(6)
RW
CM06
Watchdog Timer
Function Select Bit
0: Watchdog timer interrupt
1: Reset(7)
RW
CM07
CPU Clock Select
Bit 0(8, 9, 10)
0: Clock selected by the CM21 bit
divided by MCD register setting
1: Sub clock
RW
NOTES:
1. Rewrite the CM0 register after the PRC0 bit in the PRCR register is set to "1" (write enabled).
2. When the PM07 bit in the PM0 register is set to "0" (BCLK output), set the CM01 and CM00 bits to
"002". When the PM15 and PM14 bits in the PM1 register are set to "012" (ALE output to P53), set the
CM01 and CM00 bits to "002". When the PM07 bit is set to "1" (function selected in the CM01 and
CM00 bits) in microprocessor or memory expansion mode, and the CM01 and CM00 bits are set to
"002", an "L" signal is output from port P53 (port P53 does not function as an I/O port).
3. fc32 does not stop running. When the CM02 bit is set to "1", the PLL clock cannot be used in wait
mode.
4. When setting the CM04 bit is set to "1", set the PD8_7 and PD8_6 bits in the PD8 register to "002"
(port P87 and P86 in input mode) and the PU25 bit in the PUR2 register to "0" (no pull-up).
5. When entering low-power consumption mode or on-chip oscillator low-power consumption mode, the
CM05 bit stops running the main clock. The CM05 bit cannot detect whether the main clock stops or
not. To stop running the main clock, set the CM05 bit to "1" after the CM07 bit is set to "1" with a stable
sub clock oscillation or after the CM21 bit in the CM2 register is set to "1" (on-chip oscillator clock).
When the CM05 bit is set to "1", the clock applied to XOUT becomes "H". The built-in feedback resistor
remains ON. XIN is pulled up to XOUT ("H" level) via the feedback resistor.
6. When the CM05 bit is set to "1", the MCD4 to MCD0 bits in the MCD register are set to "010002"
(divide-by-8 mode). In on-chip oscillation mode, the MCD4 to MCD0 bits are not set to "010002" even
if the CM05 bit terminates XIN-XOUT.
7. Once the CM06 bit is set to "1", it cannot be set to "0" by program.
8. After the CM04 bit is set to "1" with a stable sub clock oscillation, set the CM07 bit to "1" from "0".
After the CM05 bit is set to "0" with a stable main clock oscillation, set the CM07 bit to "0" from "1".
Do not set the CM07 bit and CM04 or CM05 bit simultaneously.
9. When the PM21 bit in the PM2 register is set to "1" (clock change disable), the CM02, CM05 and
CM07 bits do not change even when written.
10. After the CM07 bit is set to "0", set the PM21 bit to "1".
11. When stop mode is entered, the CM03 bit is set to "1".
Figure 8.2 CM0 Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 56 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
System Clock Control Register 1(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
CM1
0 1 0 0 0 0
Bit
Symbol
CM10
(b4 - b1)
(b5)
(b6)
CM17
Address
000716
After Reset
0010 00002
Bit Name
Function
RW
All Clock Stop Control
Bit(2, 5)
0: Clock oscillates
1: All clocks stop (stop mode)(3)
RW
Reserved Bit
Set to "0"
RW
Reserved Bit
Set to "1"
RW
Reserved Bit
Set to "0"
RW
CPU Clock Select
Bit 1(4,5)
0: Main clock
1: PLL clock
RW
NOTES:
1. Rewrite the CM1 register after the PRC0 bit in the PRCR register is set to "1" (write enabled).
2. When the CM10 bit is set to "1", the clock applied to XOUT becomes "H" and the built-in feedback
resistor is disabled. XIN, XCIN and XCOUT are placed in high-impedance states.
3. When the CM10 bit is set to "1", the MCD4 to MCD0 bits in the MCD register are set to "010002"
(divide-by-8 mode). When the CM20 bit is set to "1" (oscillation stop detect function enabled) or the
CM21 bit to "1" (on-chip oscillator selected), do not set the CM10 bit to "1".
4. The CM17 bit setting is enabled only when the CM21 bit in the CM2 register is set to "0". Use the
procedure shown in Figure 8.12 to set the CM17 bit to "1".
5. If the PM21 bit in the PM2 register is set to "1" (clock change disable), the CM10 and CM17 bits do
not change when written.
If the PM22 bit in the PM2 register is set to "1" (on-chip oscillator clock as watchdog timer count
source), the CM10 bit setting does not change when written.
Figure 8.3 CM1 Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 57 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
Main Clock Division Register(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
MCD
Bit
Symbol
Address
000C16
After Reset
XXX0 10002
Bit Name
Function
RW
b4 b3 b2 b1 b0
MCD0
MCD1
MCD2
Main Clock Division
Select Bit(2, 4)
MCD3
MCD4
(b7 - b5)
Reserved Bit
1 0 0 1 0: Divide-by-1(no division)
mode
0 0 0 1 0: Divide-by-2 mode
0 0 0 1 1: Divide-by-3 mode
0 0 1 0 0: Divide-by-4 mode
0 0 1 1 0: Divide-by-6 mode
0 1 0 0 0: Divide-by-8 mode
0 1 0 1 0: Divide-by-10 mode
0 1 1 0 0: Divide-by-12 mode
0 1 1 1 0: Divide-by-14 mode
0 0 0 0 0: Divide-by-16 mode
(Note 3)
When read,
its content is indeterminate
RW
RW
RW
RW
RW
RO
NOTES:
1. Rewrite the MCD register after the PRC0 bit in the PRCR register is set to "1" (write enabled).
2. When the microcomputer enters stop mode or low-power consumption mode, the MCD4 to MCD0 bits
are set to "010002".
The MCD4 to MCD0 bits are not set to "010002" even if the CM05 bit in the CM0 register is set to "1"
(XIN-XOUT stopped) in on-chip oscillator mode.
3. Bit combinations cannot be set not listed above.
4. Access CAN-associated register addresses after setting the MCD4 to MCD0 bits are set to "100102",
when the PM24 bit in the PM2 register is set to "0" (clock selected by the CM07 bit).
Figure 8.4 MCD Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 58 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
Oscillation Stop Detection Register(1)
b7
b6
b5
b4
b3
b2
0 0 0 0
b1
b0
Symbol
CM2
Bit
Symbol
Address
000D16
After Reset
0016
Bit Name
Function
RW
CM20
Oscillation Stop Detection 0: Disables oscillation stop detect function
RW
1: Enables oscillation stop detect function
Enable Bit(2)
CM21
CPU Clock
Select Bit 2(3, 4)
CM22
Oscillation Stop Detection 0: Main clock does not stop
1: Detects a main clock stop
Flag(5)
CM23
Main Clock Monitor
Flag(6)
0: Main clock oscillates
1: Main clock stops
RO
Reserved Bit
Set to "0"
RW
(b7 - b4)
0: Clock selected by the CM17 bit
1: On-chip oscillator clock
RW
RW
NOTES:
1. Rewrite the CM2 register after the PRC0 bit in the PRCR register is set to "1" (write enabled).
2. If the PM21 bit in the PM2 register is set to "1" (clock change disable), the CM20 bit setting does not
change when written.
3. When a main clock oscillation stop is detected while the CM20 bit is set to "1", the CM21 bit is set to "1".
Although the main clock starts oscillating, the CM21 bit is not set to "0". If the main clock is used as a
CPU clock source after the main clock resumes oscillating, set the CM21 bit to "0" by program.
4. When the CM20 bit is set to "1" and the CM22 bit is set to "1", do not set the CM21 bit to "0".
5. When a main clock stop is detected, the CM22 bit is set to "1". The CM22 bit can only be set to "0", not
"1", by program.
If the CM22 bit is set to "0" by program while the main clock stops, the CM22 bit cannot be set to "1"
until the next main clock stop is detected.
6. Determine the main clock state by reading the CM23 bit several times after the oscillation stop
detection interrupt is generated.
Figure 8.5 CM2 Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 59 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
Count Source Prescaler Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
TCSPR
Bit
Symbol
Address
035F16
Bit Name
After Reset(2)
0XXX 00002
Function
CNT0
RW
CNT1
Division Rate
Select Bit(1)
CNT2
If setting value is n, f2n is the
main clock, on-chip oscillator clock
or PLL clock divided by 2n.
When n is set to "0", no division is
selected.
CNT3
(b6 - b4)
CST
RW
RW
RW
RW
Reserved Bit
Operation Enable Bit
When read,
its content is indeterminate
0: Divider stops
1: Divider starts
RO
RW
NOTES:
1. Rewrite the CNT3 to CNT0 bits after the CST bit is set to "0".
2. Value of the TCSPR register is not reset by software reset or watchdog timer reset.
Clock Prescaler Reset Flag
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
CPSRF
Bit
Symbol
Address
034116
Bit Name
After Reset
0XXX XXXX2
Function
RW
Nothing is assigned. When write, set to "0".
(b6 - b0) When read, its content is indeterminate.
CPSR
Clock Prescaler Reset
Flag
Figure 8.6 TCSPR and CPSRF Registers
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 60 of 435
When the CPSR bit is set to "1", fC
divided by 32 is reset.
When read, its content is "0".
RW
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
PLL Control Register 0(1, 2, 5)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PLC0
1 0 1
Bit
Symbol
Address
002616
After Reset
0001 X0102
Function
Bit Name
RW
RW
PLC00
b2 b1 b0
PLC01
Programmable Counter
Select Bit(3)
0 1 1: Multiply-by-6
1 0 0: Multiply-by-8
Do not set to values except the
above
PLC02
RW
Reserved Bit
When read,
its content is indeterminate
RO
Reserved Bit
Set to "1"
RW
Reserved Bit
Set to "0"
RW
Reserved Bit
Set to "1"
RW
Operation Enable Bit(4)
0: PLL is Off
1: PLL is On
RW
(b3)
(b4)
(b5)
(b6)
PLC07
RW
NOTES:
1. Rewrite the PLC0 register after the PRC0 bit in the PRCR register is set to "1" (write enabled).
2. If the PM21 bit in the PM2 register is set to "1" (clock change disabled), the PLC0 register setting does
not change when written.
3. Set the PLC02 to PLC00 bits when the PLC07 bit is set to "0". Once these bits are set, they cannot be
changed.
4. Set the CM17 bit in the CM1 register to "0" (main clock as CPU clock source) and the PLC07 bit to "0"
before entering wait or stop mode.
5. Set the PLC0 and PLC1 registers simultaneously in 16-bit units.
PLL Control Register 1(1, 2, 3, 4)
b7
b6
b5
0 0 0
b4
b3
0
b2
b1
b0
Symbol
PLC1
1 0
Bit
Symbol
(b0)
(b1)
PLC12
(b3)
(b4)
(b7 - b5)
Address
002716
After Reset
000X 00002
Bit Name
Function
RW
Reserved Bit
Set to "0"
RW
Reserved Bit
Set to "1"
RW
PLL Clock Division
Switch Bit
0: Divide-by-2
1: Divide-by-3
RW
Reserved Bit
Set to "0"
RW
Reserved Bit
When read,
its content is indeterminate
RO
Reserved Bit
Set to "0"
RW
NOTES:
1. Rewrite the PLC1 register after the PRC0 bit in the PRCR register is set to "1" (write enabled).
2. If the PM21 bit in the PM2 register is set to "1" (clock change disabled), the PLC1 register does not
change when written.
3. Set the PLC1 register when the PLC07 bit is set to "0" (PLL off).
4. Set the PLC0 and PLC1 registers simultaneously in 16-bit units.
Figure 8.7 PLC0 and PLC1 Registers
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 61 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
Processor Mode Register 2(1)
b7
b6
b5
b4
b3
b2
b1
0
b0
0
Symbol
PM2
Bit
Symbol
Address
001316
After Reset
0016
Bit Name
Function
RW
Reserved Bit
Set to "0"
RW
PM21
System Clock Protect
Bit(2, 3)
0: Protects the clock by a PRCR
register setting
1: Disables a clock change
RW
PM22
WDT Count Source
Protect Bit(2, 4)
0: Selects BCLK as count source of
the watchdog timer
RW
1: Selects the on-chip oscillator clock
as count source of the watchdog
timer
Reserved Bit
Set to "0"
RW
PM24
CPU Clock Select Bit 3
0: Clock selected by the CM07 bit
1: Main Clock
RW
PM25
CAN Clock Select Bit
0: f1
1: Main Clock
RW
(b0)
(b3)
b7 b6
PM26
PM27
f2n Count source
Select Bit
0 0: Peripheral function clock
0 1: XIN clock
1 0: On-chip oscillator clock
1 1: Do not set to this value
RW
RW
NOTES:
1. Rewrite the PM2 register after the PRC1 bit in the PRCR register is set to "1" (write enabled).
2. Once the PM22 and PM21 bits are set to "1", they can not be set to "0" by program.
3. When the PM21 bit is set to "1",
the CPU clock keeps running when the WAIT instruction is executed;
nothing is changed even if following bits are set to either "0" or "1".
• the CM02 bit in the CM0 register (the peripheral function clock is not stopped in wait mode.)
• the CM05 bit in the CM0 register (the main clock is not stopped.)
• the CM07 bit in the CM0 register (a CPU clock source is not changed.)
• the CM10 bit in the CM1 register (the microcomputer does not enter stop mode.)
• the CM17 bit in the CM1 register (a CPU clock source is not changed.)
• the CM20 bit in the CM2 register (oscillation stop detect function settings are not changed.)
• all bits in the PLC0 and PLC1 registers (PLL frequency synthesizer function settings are not changed.)
4. When the PM22 bit is set to "1",
the on-chip oscillator clock becomes a count source of the watchdog timer after the on-chip oscillator starts;
write to the CM10 bit is disabled (the microcomputer does not enter stop mode.);
the watchdog timer keeps running when the microcomputer is in wait mode and hold state.
Figure 8.8 PM2 Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 62 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
8.1.1 Main Clock
Main clock oscillation circuit generates the main clock. The main clock becomes clock source of the CPU
clock and peripheral function clock.
The main clock oscillation circuit is configured by connecting an oscillator or resonator between the XIN
and XOUT pins. The circuit has a built-in feedback resistor. The feedback resistor is separated from the
oscillation circuit in stop mode to reduce power consumption. An external clock can be applied to the XIN
pin in the main clock oscillation circuit. Figure 8.9 shows an example of a main clock circuit connection.
Circuit constants vary depending on each oscillator. Use the circuit constant recommended by each oscillator manufacturer.
The main clock divided-by-eight becomes a CPU clock source after reset.
To reduce power consumption, set the CM05 bit in the CM0 register to "1" (main clock stopped) after
switching the CPU clock source to the sub clock or on-chip oscillator clock. In this case, the clock applied
to XOUT becomes high ("H"). XIN is pulled up by XOUT via the feedback resistor which remains on. When
an external clock is applied to the XIN pin, do not set the CM05 bit to "1".
All clocks, including the main clock, stop in stop mode. Refer to 8.5 Power Consumption Control for
details.
Microcomputer
(Built-in Feedback Resistor)
Microcomputer
(Built-in Feedback Resistor)
CIN
XIN
External Clock
XIN
VCC
VSS
Oscillator
XOUT
Rd(1)
COUT
VSS
XOUT
Open
NOTE:
1. Place a damping resistor if required. Resistance values vary depending on the oscillator setting.
Use values recommended by each oscillator manufacturer.
Place a feedback resistor between XIN and XOUT if the oscillator manufacturer recommends
placing the resistor externally.
Figure 8.9 Main Clock Circuit Connection
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 63 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
8.1.2 Sub Clock
Sub clock oscillation circuit generates the sub clock. The sub clock becomes clock source of the CPU
clock and for the timers A and B. The same frequency, fc, as the sub clock can be output from the
CLKOUT pin.
The sub clock oscillation circuit is configured by connecting a crystal oscillator between the XCIN and
XCOUT pins. The circuit has a built-in feedback resistor. The feedback resistor is separated from the
oscillation circuit in stop mode to reduce power consumption. An external clock can be applied to the XCIN
pin. Figure 8.10 shows an example of a sub clock circuit connection. Circuit constants vary depending on
each oscillator. Use the circuit constant recommended by each oscillator manufacturer.
The sub clock stops after reset. The feedback resistor is separated from the oscillation circuit. When the
PD8_6 and PD8_7 bits in the PD8 register are set to "0" (input mode) and the PU25 bit in the PUR2
register is set to "0" (no pull-up), set the CM04 bit in the CM0 register to "1" (XCIN-XCOUT oscillation
function). The sub clock oscillation circuit starts oscillating. To apply an external clock to the XCIN pin, set
the CM04 bit to "1" when the PD8_7 bit is set to "0" and the PU25 bit to "0". The clock applied to the XCIN
pin becomes a clock source of the sub clock.
When the CM07 bit in the CM0 register is set to "1" (sub clock) after the sub clock oscillation has stabilized, the sub clock becomes a CPU clock source.
All clocks, including the sub clock, stop in stop mode. Refer to 8.5 Power Consumption Control for
details.
Microcomputer
(Built-in Feedback Resistor)
Microcomputer
(Built-in Feedback Resistor)
CCIN
XCIN
External Clock
XCIN
VCC
VSS
Oscillator
XCOUT
RCd(1)
CCOUT
VSS
XCOUT
Open
NOTE:
1. Place a damping resistor if required. Resistance values vary depending on the oscillator setting.
Use values recommended by each oscillator manufacturer.
Place a feedback resistor between XCIN and XCOUT if the oscillator manufacturer recommends
placing the resistor externally.
Figure 8.10 Sub Clock Circuit Connection
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 64 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
8.1.3 On-Chip Oscillator Clock
On-chip oscillator generates the on-chip oscillator clock. The 1-MHz on-chip oscillator clock becomes a
clock source of the CPU clock and peripheral function clock.
The on-chip oscillator clock stops after reset. When the CM21 bit in the CM2 register is set to "1" (on-chip
oscillator clock), the on-chip oscillator starts oscillating. Instead of the main clock, the on-chip oscillator
clock becomes clock source of the CPU clock and peripheral function clock.
Table 8.2 shows bit settings for on-chip oscillator start condition.
Table 8.2 Bit Settings for On-Chip Oscillator Start Condition
CM2 Register
PM2 Register
Used as
CM21 Bit
PM22 Bit
PM27 and PM26 Bits
1
0
00
CPU clock source or peripheral function clock
source
0
1
00
Watchdog timer operating clock source
(The clock keeps running when entering stop mode.)
0
0
01
f2n count source
8.1.3.1 Oscillation Stop Detect Function
When the main clock is terminated by external source, the on-chip oscillator automatically starts oscillating to generate another clock.
When the CM 20 bit in the CM2 registser is set to "1" (oscillation stop detect function enabled), an oscillation stop detection interrupt request is generated as soon as the main clock stops. Simultaneously, the onchip oscillator starts oscillating. Instead of the main clock, the on-chip oscillator clock becomes clock
source for the CPU clock and peripheral function clock. Associated bits are set as follows:
• The CM21 bit is set to "1" (on-chip oscillator clock becomes a clock source of the CPU clock.)
• The CM22 bit is set to "1" (main clock stop is detected.)
• The CM23 bit is set to "1" (main clock stops.) (See Figure 8.14)
8.1.3.2 How to Use Oscillation Stop Detect Function
• The oscillation stop detection interrupt shares vectors with the watchdog timer interrupt. When
these interrupts are used simultaneously, read the CM22 bit with an interrupt routine to determine if
an oscillation stop detection interrupt request has been generated.
• When the main clock resumes running after an oscillation stop is detected, set the main clock as
clock source of the CPU clock and peripheral function clock. Figure 8.11 shows the procedure to
switch the on-chip oscillator clock to the main clock.
• In low-speed mode, when the main clock is stopped by setting the CM20 bit to "1", the oscillation
stop detection interrupt request is generated. Simultaneously, the on-chip oscillator starts oscillating. The sub clock remains the CPU clock source. The on-chip oscillator clock becomes a clock
source for the peripheral function clock.
• When the peripheral function clock stops running, the oscillation stop detect function is also disabled. To enter wait mode while the oscillation stop detect function is in use, set the CM02 bit in the
CM0 register to "0" (peripheral clock does not stop in wait mode).
• The oscillation stop detect function is provided to handle main clock stop caused by external source.
Set the CM20 bit to "0" (oscillation stop detect function disabled) when the main clock is terminated
by program, i.e., entering stop mode or setting the CM05 bit to "1" (main clock oscillation stop).
• When the main clock frequency is 2MHz or less, the oscillation stop detect function is not available.
Set the CM20 bit to "0".
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 65 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
Switch to the main clock
No
Determine several times whether
the CM23 bit is set to "0"
(main clock oscillates)
Yes
Set the MCD4 to MCD0 bits
to "010002" (divide-by-8 mode)
Set the CM22 bit to "0"
(main clock does not stop)
Set the CM21 bit to "0"
(main clock as CPU clock source)
End
MCD4 to MCD0 bits: Bits in the MCD Register
CM23 to CM21 bits: Bits in the CM2 Register
Figure 8.11 Switching Procedure from On-chip Oscillator Clock to Main Clock
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 66 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
8.1.4 PLL Clock
The PLL frequency synthesizer generates the PLL clock based on the main clock. The PLL clock can be
used as clock source for the CPU clock and peripheral function clock.
The PLL frequency synthesizer stops after reset. When the PLC07 bit is set to "1" (PLL on), the PLL
frequency synthesizer starts operating. Wait tsu(PLL) ms for the PLL clock to stabilize.
The PLL clock can either be the clock output from the voltage controlled oscillator (VCO) divided-by-2 or
divided-by-3. When the PLL clock is used as a clock source for the CPU clock or peripheral function
clock, set each bit as is shown in Table 8.3. Figure 8.12 shows the procedure to use the PLL clock as the
CPU clock source.
To enter wait or stop mode, set the CM17 bit to "0" (main clock as CPU clock source), set the PLC07 bit
in the PLC0 register to "0" (PLL off) and then enter wait or stop mode.
Table 8.3 Bit Settings to Use PLL Clock as CPU Clock Source
PLC0 Register
PLC1 Register
f(XIN)
10 MHz
PLL Clock
PLC02 Bit
PLC01 Bit
PLC00 Bit
0
1
1
8 MHz
1
0
PLC12 Bit
0
30 MHz
1
20 MHz
0
32 MHz
1
21.3 MHz
0
Use PLL clock as CPU clock source
Set the PLC0 and the PLC1 registers
(Set the PLC07 bit to "0")
Set the PLC07 bit to "1"
(PLL on)
Wait tsu(PLL)ms
Set the CM17 bit to "1"
(PLL clock as CPU clock source)
End
PLC07 bit: Bit in the PLC0 Register
CM17 bit: Bit in the CM1 Register
Figure 8.12 Procedure to Use PLL Clock as CPU Clock Source
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 67 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
8.2 CPU Clock and BCLK
The CPU operating clock is referred to as the CPU clock. The CPU clock is also a count source for the
watchdog timer. After reset, the CPU clock is the main clock divided-by-8 . In memory expansion or microprocessor mode, the clock having the same frequency as the CPU clock can be output from the BCLK pin
as BCLK. Refer to 8.4 Clock Output Function for details.
The main clock, sub clock, on-chip oscillator clock or PLL clock can be selected as a clock source for the
CPU clock. Table 8.4 shows CPU clock source and bit settings.
When the main clock, on-chip oscillator clock or PLL clock is selected as a clock source of the CPU clock,
the selected clock divided-by-1 (no division), -2, -3, -4, -6, -8, -10, -12, -14 or -16 becomes the CPU clock.
The MCD4 to MCD0 bits in the MCD register select the clock division.
When the microcomputer enters stop mode or low-power consumption mode (except when the on-chip
oscillator clock is the CPU clock), the MCD4 to MCD0 bits are set to "010002" (divide-by-8 mode). Therefore, when the main clock starts running, the CPU clock enters medium-speed mode (divide-by-8).
Table 8.4 CPU Clock Source and Bit Settings
CM0 Register CM1 Register CM2 Register
PM2 Register
CPU Clock Source
CM07 Bit
CM17 Bit
CM21 Bit
PM24 Bit
Main Clock
0
0
0
0
Main Clock (Main Clock Direct Mode)(1)
0
0
0
1
Sub Clock
1
0
0
0
On-Chip Oscillator Clock
0
0
1
0
PLL Clock
0
1
0
0
NOTE:
1. Refer to 22.2 CAN Clock for details.
8.3 Peripheral Function Clock
The peripheral function clock becomes an operating clock or count source for peripheral functions excluding the watchdog timer.
8.3.1 f1, f8, f32 and f2n
f1, f8 and f32 are the peripheral function clock, selected by the CM21 bit, divided-by-1, -8, or -32. The
PM27 and PM26 bits in the PM2 register selects a f2n count source from the peripheral clock, XIN clock,
and the on-chip oscillator clock. The CNT3 to CNT0 bits in the TCSPR register selects a f2n division. (n=0
to 15. No division when n=0.)
f1, f8, f32 and f2n stop when the CM02 bit in the CM0 register to "1" (peripheral function stops in wait mode)
to enter wait mode or when in low-power consumption mode.
f1, f8 and f2n are used as an operating clock of the serial I/O and count source of the timers A and B. f1 is
also used as an operating clock for the intelligent I/O.
The CLKOUT pin outputs f8 and f32 . Refer to 8.4 Clock Output Function for details.
8.3.2 fAD
fAD is an operating clock for the A/D converter and has the same frequency as either the main clock(1) or
the on-chip oscillator clock. The CM21 bit determines which clock is selected.
If the CM02 bit is set to "1" (peripheral function stop in wait mode) to enter wait mode, fAD stops. fAD also
stops in low-power consumption mode.
NOTE:
1. The PLL clock, instead of the main clock, when the CM17 bit is set to "1" (PLL clock).
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 68 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
8.3.3 fC32
fC32 is the sub clock divided by 32. fC32 is used as a count source for the timers A and B. fC32 is available
when the sub clock is running.
8.3.4 fCAN
fCAN has the same frequency as the main clock. It is a clock for the CAN module only.
8.4 Clock Output Function
The CLKOUT pin outputs fC, f8 or f32.
In memory expansion mode or microprocessor mode, a clock having the same frequency as the CPU clock
can be output from the BCLK pin as BCLK.
Table 8.5 lists CLKOUT pin function in single-chip mode.
Table 8.5 CLKOUT Pin in Single-Chip Mode
PM0 Register (1)
PM07 Bit
CM0 Register (2)
CLKOUT Pin Function
CM01 Bit
0
CM00 Bit
0
1
0
1
Outputs fc
1
1
0
Outputs f8
1
1
1
Outputs f32
P53 I/O port
- : Can be set to either "0" or "1"
NOTES:
1. Rewrite the PM0 register after the PRC1 bit in the PRCR register is set to "1" (write enabled).
2. Rewrite the CM0 register after the PRC0 bit in the PRCR register is set to "1" (write enabled).
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 69 of 435
M32C/88 Group (M32C/88T)
8. Clock Generation Circuit
8.5 Power Consumption Control
Normal operating mode, wait mode and stop mode are provided as the power consumption control.
All mode states, except wait mode and stop mode, are called normal operating mode in this section. Figure
8.13 shows a block diagram of status transition in wait mode and stop mode. Figure 8.14 shows a block
diagram of status transition in all modes.
8.5.1 Normal Operating Mode
The normal operating mode is further separated into six modes.
In normal operating mode, the CPU clock and peripheral function clock are supplied to operate the CPU
and peripheral function. The power consumption control is enabled by controlling a CPU clock frequency. The higher the CPU clock frequency is, the more processing power increases. The lower the
CPU clock frequency is, the more power consumption decreases. When unnecessary oscillation circuit
stops, power consumption is further reduced.
8.5.1.1 High-Speed Mode
The main clock(1) becomes the CPU clock and a clock source of the peripheral function clock. When
the sub clock runs, fC32 can be used as a count source for the timers A and B.
8.5.1.2 Medium-Speed Mode
The main clock(1) divided-by-2, -3, -4, -6, -8, -10, -12, -14, or -16 becomes the CPU clock. The main
clock(1) is a clock source for the peripheral function clock. When the sub clock runs, fC32 can be used
as a count source for the timers A and B.
8.5.1.3 Low-Speed Mode
The sub clock becomes the CPU clock . The main clock(1) is a clock source for the peripheral function
clock. fC32 can be used as a count source for the timers A and B.
8.5.1.4 Low-Power Consumption Mode
The microcomputer enters low-power consumption mode when the main clock stops in low-speed
mode. The sub clock becomes the CPU clock. Only fC32 can be used as a count source for the timers
A and B and the peripheral function clock. In low-power consumption mode, the MCD4 to MCD0 bits
in the MCD register are set to "010002" (divide-by-8 mode). Therefore, when the main clock resumes
running, the microcomputer is in midium-speed mode (divide-by-8 mode).
8.5.1.5 On-Chip Oscillator Mode
The on-chip oscillator clock divided-by-1 (no division), -2, -3, 4-, -6, -8, -10, -12, -14, or -16 becomes
the CPU clock. The on-chip oscillator clock is a clock source for the peripheral function clock. When
the sub clock runs, fC32 can be used as a count source for the timers A and B.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 70 of 435
M32C/88 Group (M32C/88T)
8. Clock Generation Circuit
8.5.1.6 On-Chip Oscillator Low-Power Consumption Mode
The microcomputer enters on-chip oscillator low-power consumption mode when the main clock stops
in on-chip oscillator mode . The on-chip oscillator clock divided-by-1 (no division), -2, -3, -4, -6, -8, -10, 12, -14, or -16 becomes the CPU clock. The on-chip oscillator clock is a clock source for the peripheral
function clock. When the sub clock runs, fC32 can be used as a count source for the timers A and B.
Switch the CPU clock after the clock to be switched to stabilize. Sub clock oscillation will take longer(2)
to stabilize. Wait, by program, until the clock stabilizes directly after turning the microcomputer on or
exiting stop mode.
To switch the on-chip oscillator clock to the main clock, enter medium-speed mode (divide-by-8) after
the main clock is divided by eight in on-chip oscillator mode (the MCD4 to MCD0 bits in the MCD
register are set to "010002").
Do not enter on-chip oscillator mode or on-chip oscillator low-power consumption mode from lowspeed mode or low-power consumption mode and vice versa.
NOTES:
1. The PLL clock, instead of the main clock, when the CM17 bit is set to "1" (PLL clock).
2. Contact your oscillator manufacturer for oscillation stabilization time.
8.5.2 Wait Mode
In wait mode, the CPU clock stops running. The CPU and watchdog timer, operated by the CPU clock,
also stop. When the PM22 bit in the PM2 register is set to "1" (on-chip oscillator clock as watchdog timer
count source), the watchdog timer continues operating. Because the main clock, sub clock and on-chip
oscillator clock continue running, peripheral functions using these clocks also continue operating.
8.5.2.1 Peripheral Function Clock Stop Function
If the CM02 bit in the CM0 register is set to "1" (peripheral function clock stops in wait mode), f1, f8, f32,
f2n (when peripheral clock is selected as a count source), and fAD stop in wait mode. Power consumption can be reduced. f2n, when XIN clock or on-chip oscillator clock is selected as a count source, and
fC32 do not stop running.
8.5.2.2 Entering Wait Mode
If wait mode is entered after setting the CM02 bit to "1", set the MCD4 to MCD0 bits in the MCD
register to be the 10-MHz or less CPU clock flequency after dividing the main clock.
Enter wait mode after setting the followings.
• Initial Setting
Set each interrupt priority level after setting the exit priority level required to exit wait mode, controlled by the RLVL2 to RLVL0 bits in the RLVL register, to "7".
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 71 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
• Before Entering Wait Mode
(1) Set the I flag to "0"
(2) Set the interrupt priority level of the interrupt being used to exit wait mode
(3) Set the interrupt priority levels of the interrupts, not being used to exit wait mode, to "0"
(4) Set IPL in the FLG register. Then set the exit priority level to the same level as IPL
Interrupt priority level of the interrupt used to exit wait mode > IPL = the exit priority level
(5) Set the PRC0 bit in the PRCR register to "1"
(6) If the CPU clock source is the PLL clock, set the CM17 bit in the CM1 register to "0" (main clock)
and PLC07 bit in the PLC0 register to "0" (PLL off)
(7) Set the I flag to "1"
(8) Execute the WAIT instruction
• After Exiting Wait Mode
Set the exit priority level to "7" as soon as exiting wait mode.
8.5.2.3 Pin Status in Wait Mode
Table 8.6 lists pin states in wait mode.
Table 8.6 Pin States in Wait Mode
Pin
Ports
Single-Chip Mode
Maintains state immediately before entering wait mode
CLKOUT
When fC is selected
Outputs clock
When f8, f32 are selected Outputs the clock when the CM02 bit in the CM0 register is set to
"0" (peripheral function clock does not stop in wait mode).
Maintains state immediately before entering wait mode when the
CM02 bit is set to "1" (peripheral function clock stops in wait mode).
8.5.2.4 Exiting Wait Mode
_______
Wait mode is exited by the hardware reset, NMI interrupt or peripheral function interrupts.
_______
When the hardware reset or NMI interrupt, but not the peripheral function interrupts, is used to exit wait
mode, set the ILVL2 to ILVL0 bits for the peripheral function interrupts to "0002" (interrupt disabled)
before executing the WAIT instruction.
CM02 bit setting affects the peripheral function interrupts. When the CM02 bit in the CM0 register is
set to "0" (peripheral function clock does not stop in wait mode), all peripheral function interrupts can
be used to exit wait mode. When the CM02 bit is set to "1" (peripheral function clock stops in wait
mode), peripheral functions using the peripheral function clock stop. Therefore, the peripheral function
interrupts cannot be used to exit wait mode. However, the peripheral function interrupts caused by an
external clock, fC32, or f2n whose count source is the XIN clock or on-chip oscillator clock, can be used
to exit wait mode.
_______
The CPU clock used when exiting wait mode by the peripheral function interrupts or NMI interrupt is
the same CPU clock used when the WAIT instruction is executed.
Table 8.7 shows interrupts to be used to exit wait mode and usage conditions.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 72 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
Table 8.7 Interrupts to Exit Wait Mode
Interrupt
When CM02=0
When CM02=1
NMI Interrupt
Can be used
Can be used
Serial I/O Interrupt
Can be used when either internal
or external clock is selected
Can be used when external clock or f2n
(when XIN clock or on-chip oscillator is
selected) is selected
Key Input Interrupt
Can be used
Can be used
A/D Conversion Interrupt
Can be used in single or singlesweep mode
Do not use
Timer A Interrupt
Timer B Interrupt
Can be used in all modes
Can be used in event counter mode or
when count source is fC32 or f2n (when
XIN clock or on-chip oscillator is selected)
INT Interrupt
Can be used
Can be used
CAN Interrupt
Can be used
Do not use
Intelligent I/O Interrupt
Can be used
Do not use
8.5.3 Stop Mode
In stop mode, all oscillators and resonators stop. The CPU clock and peripheral function clock, as well as
the CPU and peripheral functions operated by these clocks, also stop. The least power required to
operate the microcomputer is in stop mode. The internal RAM holds its data when the voltage applied to
the VCC pin is VRAM or more. If the voltage applied to the VCC pin is 2.7V or less, the voltage must be Vcc
≥ VRAM.
The following interrupts can be used to exit stop mode:
_______
• NMI interrupt
• Key Input Interrupt
______
• INT interrupt
• Timer A and B interrupt (Available when the timer counts external pulse, having its 100Hz or less
frequency, in event counter mode)
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 73 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
8.5.3.1 Entering Stop Mode
Stop mode is entered when setting the CM10 bit in the CM10 register to "1" (all clocks stops). The
MCD4 to MCD0 bits in the MCD register become set to "010002" (divide-by-8 mode).
Enter stop mode after setting the followings.
• Initial Setting
Set each interrupt priority level after setting the exit priority level required to exit stop mode, controlled by the RLVL2 to RLVL0 bits in the RLVL register, to "7".
• Before Entering stop mode
(1) Set the I flag to "0"
(2) Set the interrupt priority level of the interrupt being used to exit stop mode
(3) Set the interrupt priority levels of the interrupts, not being used to exit stop mode, to "0"
(4) Set IPL in the FLG register. Then set the exit priority level to the same level as IPL
Interrupt priority level of the interrupt used to exit stop mode > IPL = the exit priority level
(5) Set the PRC0 bit in the PRCR register to "1" (write enabled)
(6) Select the main clock as the CPU clock
• When the CPU clock source is the sub clock,
(a) set the CM05 bit in the CM0 register to "0" (main clock oscillates)
(b) set the CM07 bit in the CM0 register to "0" (clock selected by the CM21 bit divided by MCD
register setting)
• When the CPU clock source is the PLL clock,
(a) set the CM17 bit in the CM1 register to "0" (main clock)
(b) set the PLC07 bit in the PLC0 register to "0" (PLL off)
• When main clock direct mode is used,
(a) set the PRC1 bit in the PRCR register to "1" (write enabled)
(b) set the PM24 bit in the PM2 register to "0" (clock selected by the CM07 bit)
• When the CPU clock source is the on-chip oscillator clock,
(a) set MCD4 to MCD0 bits to "010002" (divide-by-8 mode)
(b) set the CM05 bit to "0" (main clock oscillates)
(c) set the CM21 bit in the CM2 register to "0" (clock selected by the CM17 bit)
(7) The oscillation stop detect function is used, set the CM20 bit in the CM2 register to "0" (oscillation stop detect fucntion disabled)
(8) Set the I flag to "1"
(9) Set the CM10 bit to "1" (all clocks stops)
• After Exiting Stop Mode
Set the exit priority level to "7" as soon as exiting stop mode.
8.5.3.2 Exiting Stop Mode
_______
Stop mode is exited by the hardware reset, NMI interrupt or peripheral function interrupts (key input
______
interrupt and INT interrupt).
_______
When the hardware reset or NMI interrupt, but not the peripheral function interrupts, is used to exit wait
mode, set all ILVL2 to ILVL0 bits in the interrupt control registers for the peripheral function interrupt to
"0002" (interrupt disabled) before setting the CM10 bit to "1" (all clocks stops).
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 74 of 435
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
8.5.3.3 Pin Status in Stop Mode
Table 8.8 lists pin status in stop mode.
Table 8.8 Pin Status in Stop Mode
Pin
Single-Chip Mode
Ports
Maintains state immediately before entering stop mode
CLKOUT
When fC selected
"H"
When f8, f32 selected
Maintains state immediately before entering stop mode
XIN
Placed in a high-impedance state
XOUT
"H"
XCIN, XCOUT
Placed in a high-impedance state
Reset
All oscillation is stopped
CPU operation is stopped
CM10=1
(Note 2)
Stop Mode
Interrupt
Inter
Stop Mode
rupt
CM10=1
Middle-Speed Mode
(divide-by-8 mode)
(Note 2)
WAIT Instruction
Interrupt
Wait Mode
(Note 1)
(Note 2)
High-Speed/
Middle-Speed Mode
(Note 2)
(Note 1)
WAIT Instruction
Wait Mode
Interrupt
(Note 3)
Low-Speed/Low-Power
Consumption Mode
On-Chip Oscillator/OnChip Oscillator Low-Power
Consumption Mode
WAIT Instruction
Wait Mode
Interrupt
WAIT Instruction
Interrupt
Wait Mode
Normal Operating Mode
NOTES:
1. See Figure 8.14.
2. When the CM17 bit is set to "1" (PLL clock as CPU clock source), set the CM17 bit to "0"(main clock as CPU clock source)
and the PLC07 bit is set to "0" (PLL off). Then enter wait mode or stop mode.
3. When the CM17 bit is set to "1" (PLL clock as CPU clock source), set the CM17 bit to "0"(main clock as CPU clock source)
and the PLC07 bit is set to "0" (PLL off). Then enter low-speed or low-power consumption mode.
Figure 8.13 Status Transition in Wait Mode and Stop Mode
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 75 of 435
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Figure 8.14 Status Transition
Page 76 of 435
CM17=0
PLC07=0
PLC07=1
NOTES:
1. Switch the clock after main clock oscillation is fully stabilized.
2. Switch the clock after sub clock oscillation is fully stabilized.
3. The MCD4 to MCD0 bits in the MCD register are set to "010002" (devide-by-8
mode) automatically.
4. The CM05 bit is not set to "1" when the microcomputer detects a main clock
oscillation stop through the oscillation stop detection circuit .
5. The on-chip oscillator clock runs when setting the PM22 bit to "1" (on-chip
oscillator clock as watchdog timer count source) and setting the PM27 and
PM26 bits to "102" (on-chip oscillator clock), even if the CM21 bit is set to "0".
(Note 5)
Main clock stop
is detected when
CM20=1
Medium-Speed Mode
CPU clock: f(XIN)/n
(n=2,3,4,6,8,10,12,14,16)
CM07=0 MCD=XX16 CM21=0
CM05=0 CM04=0 PLC07=1
CM17=0
: An arrow shows mode can be changed.
Do not change mode to another mode when no arrow is shown.
MCD=XX16: Set the MCD to MCD0 bits in the MCD register to the desired division.
Medium-Speed Mode
CPU clock: f(XPLL)/n
(n=2,3,4,6,8,10,12,14,16)
CM07=0 MCD=XX16 CM21=0
CM05=0 CM04=0 PLC07=1
CM17=1
CPU clock: f(XIN)
CM07=0 MCD=1216 CM21=0
CM05=0 CM04=0 PLC07=1
CM17=0
High-Speed Mode
CM17=1
High-Speed Mode
CPU clock: f(XPLL)
CM07=0 MCD=1216 CM21=0
CM05=0 CM04=0 PLC07=1
CM17=1
Main Clock Oscillation
Sub Clock Stop
On-Chip Oscillator Clock Stop
PLL Clock Oscillation
Main Clock Oscillation
Sub Clock Stop
On-Chip Oscillator Clock Stop
PLL Clock Oscillation
CM05=1
On-Chip Oscillator Low-Power
Consumption Mode
Main Clock Stop
Sub Clock Stop
CM04=0
On-Chip Oscillator Clock Oscillation
PLL Clock Stop
CPU Clock: On-Chip Oscillator Clock /n
(n=1,2,3,4,6,8,10,12,14,16)
CM04=1
CM07=0 MCD=XX16 CM21=1
CM05=1 CM04=0 PLC07=0
CM17=0
CM05=0
(Note 4)
CM05=1
CM07=1 (Note 2)
CM07=0 (Note 1)
Medium-Speed Mode
CPU clock: f(XIN)/n
(n=2,3,4,6,8,10,12,14,16)
CM07=0 MCD=XX16 CM21=0
CM05=0 CM04=1 PLC07=1
CM17=0
CM21=0
CM05=0
(Note 3)
Main Clock Stop
Sub Clock Oscillation
On-Chip Oscillator Clock Oscillation
PLL Clock Stop
CPU Clock: f(XCIN)
CM07=1 MCD=0816 CM21=1
CM05=1 CM04=1 PLC07=0
CM17=0
CM05=0
Main Clock Stop
Sub Clock Oscillation
On-Chip Oscillator Clock Stop
PLL Clock Stop
CPU Clock: f(XCIN)
CM07=1 MCD=0816 CM21=0
CM05=1 CM04=1 PLC07=0
CM17=0
Low-Power Consumption Mode
CM05=1
CM21=1
(Note 1)
Main Clock Oscillation
Sub Clock Oscillation
On-Chip Oscillator Clock Stop
PLL Clock Stop
CPU clock: f(XCIN)
CM07=1 CM21=0 CM05=0
CM04=1 PLC07=0
CM17=0
Main Clock Oscillation
Sub Clock Oscillation
On-Chip Oscillator Clock Oscillation
PLL Clock Stop
CPU Clock: f(XCIN)
CM07=1 CM21=1 CM05=0
CM04=1 PLC07=0
CM17=0
Low-Power Consumption Mode
CM07=1
(Note 2)
CM07=0
Low-Speed Mode
(Note 3)
CM05=1
Medium-Speed Mode
CPU clock: f(XPLL)/n
(n=2,3,4,6,8,10,12,14,16)
CM07=0 MCD=XX16 CM21=0
CM05=0 CM04=1 PLC07=1
CM17=1
Low-Speed Mode
CM17=1
CPU clock: f(XPLL)
CM07=0 MCD=1216 CM21=0
CM05=0 CM04=1 PLC07=1
CM17=1
High-Speed Mode
CM17=0
High-Speed Mode
CPU clock: f(XIN)
CM07=0 MCD=1216 CM21=0
CM05=0 CM04=1 PLC07=1
CM17=0
Main Clock Oscillation
Sub Clock Oscillation
On-Chip Oscillator Clock Stop
PLL Clock Oscillation
Main Clock Oscillation
Sub Clock Oscillation
On-Chip Oscillator Clock stop
PLL Clock Oscillation
Main clock stop
is detected when
CM20=1
PLC07=1
PLC07=0
CM21=1
Main Clock Stop
Sub Clock Oscillation
On-Chip Oscillator Clock Oscillation
PLL Clock Stop
CPU Clock: On-Chip Oscillator Clock /n
(n=1,2,3,4,6,8,10,12,14,16)
CM07=0 MCD=XX16 CM21=1
CM05=1 CM04=1 PLC07=0
CM17=0
CM05=0
On-Chip Oscillator Low-Power
Consumption Mode
Main Clock Oscillation
Sub Clock Oscillation
On-Chip Oscillator Clock Oscillation
PLL Clock Stop
CPU Clock: On-Chip Oscillator Clock /n
(n=1,2,3,4,6,8,10,12,14,16)
CM07=0 MCD=XX16 CM21=1
CM05=0 CM04=1 PLC07=0
CM17=0
Main Clock Oscillation
Sub Clock Stop
On-Chip Oscillator Clock Oscillation
CM04=0
PLL Clock Stop
CPU Clock: On-Chip Oscillator Clock /n
(n=1,2,3,4,6,8,10,12,14,16)
CM04=1
CM07=0 MCD=XX16 CM21=1
CM05=0 CM04=0 PLC07=0
CM17=0
(Note 1) CM21=0
Medium-Speed Mode
CPU clock: f(XIN)/n
(n=2,3,4,6,8,10,12,14,16)
CM07=0 MCD=XX16 CM21=0
CM05=0 CM04=1 PLC07=0
CM17=0
On-Chip Oscillator Mode
CM21=1
CM04=1
On-Chip Oscillator Mode
(Note 1) CM21=0
Medium-Speed Mode
CPU clock: f(XIN)/n
(n=2,3,4,6,8,10,12,14,16)
CM07=0 MCD=XX16 CM21=0
CM05=0 CM04=0 PLC07=0
CM17=0
CPU clock :f(XIN)
CM07=0 MCD=1216 CM21=0
CM05=0 CM04=1 PLC07=0
CM17=0
High-Speed Mode
High-Speed Mode
CPU clock: f(XIN)
CM07=0 MCD=1216 CM21=0
CM05=0 CM04=0 PLC07=0
CM17=0
Main Clock Oscillation
Sub Clock Oscillation
On-Chip Oscillator Clock Stop
PLL Clock Stop
CM04=1 (Note 1)
Main Clock Oscillation
Sub Clock Stop
On-Chip Oscillator Clock Stop
PLL Clock Stop
CM04=0
MCD=XX16 (Note 1)
After reset,
Medium-Speed Mode (Divide-by-8)
Main Clock Oscillation
Sub Clock Stop
On-Chip Oscillator Clock Stop
PLL Clock Stop
CPU Clock: f(XIN)/8
CM07=0 MCD=0816 CM21=0
CM05=0 CM04=0 PLC07=0
CM17=0
M32C/88 Group (M32C/88T)
8. Clock Generation Circuit
M32C/88 Group (M32C/88T)
8. Clock Generation Circuit
8.6 System Clock Protect Function
The system clock protect function prohibits the CPU clock from changing clock sources when the main
clock is selected as the CPU clock source. This prevents the CPU clock from stopping the program crash.
When the PM21 bit in the PM2 register is set to "1" (clock change disabled), the following bits cannot be
written to:
• The CM02 bit, CM05 bit and CM07 bit in the CM0 register
• The CM10 bit and CM17 bit in the CM1 register
• The CM20 bit in the CM2 register
• All bits in the PLC0 and PLC1 registers
The CPU clock continues running when the WAIT instruction is executed.
To use the system clock protect function, set the CM05 bit in the CM0 register to "0" (main clock oscillation)
and CM07 bit to "0" (main clock as BCLK clock source) and follow the procedure below.
(1) Set the PRC1 bit in the PRCR register to "1" (write enabled).
(2) Set the PM21 bit in the PM2 register to "1" (protects the clock).
(3) Set the PRC1 bit in the PRCR register to "0" (write disabled).
When the PM21 bit is set to "1", do not execute the WAIT instruction.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 77 of 435
9. Protection
M32C/88 Group (M32C/88T)
9. Protection
The protection function protects important registers from being easily overwritten when a program runs out of
control.
Figure 9.1 shows the PRCR register. Individual bit in the PRCR register protects the following registers:
• The PRC0 bit protects the CM0, CM1, CM2, MCD, PLC0, and PLC1 registers;
• The PRC1 bit protects the PM0, PM1, PM2, INVC0, and INVC1 registers;
• The PRC2 bit protects the PD9 and PS3 registers.
The PRC2 bit is set to "0" (write disabled) when data is written to a given address after setting the PRC2 bit
to "1" (write enabled). Set the PD9 and PS3 registers immediately after setting the PRC2 bit in the PRCR
register to "1" (write enabled). Do not generate an interrupt or a DMA transfer between the instruction to set
to the PRC2 bit to "1" and the following instruction. The PRC0 and PRC1 bits are not set to "0" even if data
is written to a given address. Set the PRC0 and PRC1 bits to "0" by program.
Protect Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PRCR
0
Bit
Symbol
Address
000A16
After Reset
XXXX 00002
Bit Name
Function
Protect Bit 0
Enables writing to CM0, CM1, CM2,
MCD, PLC0, PLC1 registers
0: Write disabled
1: Write enabled
RW
PRC1
Protect Bit 1
Enables writing to PM0, PM1, PM2,
INVC0, INVC1 registers
0: Write disabled
1: Write enabled
RW
PRC2
Protect Bit 2(1)
Enables writing to PD9, PS3 registers
0: Write disabled
1: Write enabled
RW
Reserved Bit
Set to "0"
RW
PRC0
(b3)
Nothing is assigned. When write, set to "0".
(b7 - b4) When read, its content is indeterminate.
NOTE:
1. The PRC2 bit is set to "0" by writing into a given address after the PRC2 bit is set to "1".
The PRC0 and PRC1 bits are not automatically set to "0". Set them to "0" by program.
Figure 9.1 PRCR Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
RW
Page 78 of 435
10. Interrupts
M32C/88 Group (M32C/88T)
10. Interrupts
10.1 Types of Interrupts
Figure 10.1 shows types of interrupts.










Hardware
Special
(Non-Maskable Interrupt)















Interrupt
Software
(Non-Maskable Interrupt)
Undefined Instruction (UND Instruction)
Overflow (INTO Instruction)
BRK Instruction
BRK2 Instruction(2)
INT Instruction
_______
NMI
Watchdog Timer
Oscillation Stop Detection
Single-Step(2)
Address Match
DMACII
Peripheral Function(1)
(Maskable Interrupt)
NOTES:
1. The peripheral functions in the microcomputer are used to generate the peripheral interrupt.
2. Do not use this interrupt. For development support tools only.
Figure 10.1 Interrupts
• Maskable Interrupt
The I flag enables or disables an interrupt.
The interrupt priority order based on interrupt priority level can be changed.
• Non-Maskable Interrupt
The I flag does not enable nor disable an interrupt .
The interrupt priority order based on interrupt priority level cannot be changed.
Rev. 1.10 Oct. 18, 2005 Page 79
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
10.2 Software Interrupts
Software interrupt occurs when an instruction is executed. The software interrupts are non-maskable interrupts.
10.2.1 Undefined Instruction Interrupt
The undefined instruction interrupt occurs when the UND instruction is executed.
10.2.2 Overflow Interrupt
The overflow interrupt occurs when the O flag in the FLG register is set to "1" (overflow of arithmetic
operation) and the INTO instruction is executed.
Instructions to set the O flag are :
ABS, ADC, ADCF, ADD, ADDX, CMP, CMPX, DIV, DIVU, DIVX, NEG, RMPA, SBB, SCMPU, SHA, SUB, SUBX
10.2.3 BRK Interrupt
The BRK interrupt occurs when the BRK instruction is executed.
10.2.4 BRK2 Interrupt
The BRK2 interrupt occurs when the BRK2 instruction is executed.
Do not use this interrupt. For development support tools only.
10.2.5 INT Instruction Interrupt
The INT instruction interrupt occurs when the INT instruction is executed. The INT instruction can select
software interrupt numbers 0 to 63. Software interrupt numbers 8 to 50, 52 to 54 and 57 are assigned to the
vector table used for the peripheral function interrupt. Therefore, the microcomputer executes the same
interrupt routine when the INT instruction is executed as when a peripheral function interrupt occurs.
When the INT instruction is executed, the FLG register and PC are saved to the stack. PC also stores the
relocatable vector of specified software interrupt numbers. Where the stack is saved varies depending
on a software interrupt number. ISP is selected as the stack for software interrupt numbers 0 to 31
(setting the U flag to "0"). SP, which is set before the INT instruction is executed, is selected as the stack
for software interrupt numbers 32 to 63 (the U flag is not changed).
With the peripheral function interrupt, the FLG register is saved and the U flag is set to "0" (ISP select)
when an interrupt request is acknowledged. With software interrupt numbers 32 to 50, 52 to 54 and 57,
SP to be used varies depending on whether the interrupt is generated by the peripheral function interrupt
request or by the INT instruction.
Rev. 1.10 Oct. 18, 2005 Page 80
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
10.3 Hardware Interrupts
Special interrupts and peripheral function interrupts are available as hardware interrupts.
10.3.1 Special Interrupts
Special interrupts are non-maskable interrupts.
______
10.3.1.1 NMI Interrupt
______
______
The NMI interrupt occurs when a signal applied to the NMI pin changes from a high-level ("H") signal
______
to a low-level ("L") signal. Refer to 10.8 NMI Interrupt for details.
10.3.1.2 Watchdog Timer Interrupt
The watchdog timer interrupt occurs when a count source of the watchdog timer underflows. Refer to
11. Watchdog Timer for details.
10.3.1.3 Oscillation Stop Detection Interrupt
The oscillation stop detection interrupt occurs when the microcomputer detects a main clock oscillation stop. Refer to 8. Clock Generation Circuit for details.
10.3.1.4 Single-Step Interrupt
Do not use the single-step interrupt. For development support tool only.
10.3.1.5 Address Match Interrupt
The address match interrupt occurs immediately before executing an instruction that is stored into an
address indicated by the RMADi register (i=0 to 7) when the AIERi bit in the AIER register is set to "1"
(address match interrupt enabled). Set the starting address of the instruction in the RMADi register.
The address match interrupt does not occur when a table data or addresses of the instruction other
than the starting address, if the instruction has multiple addresses, is set. Refer to 10.10 Address
Match Interrupt for details.
10.3.2 Peripheral Function Interrupt
The peripheral function interrupt occurs when a request from the peripheral functions in the microcomputer is acknowledged. The peripheral function interrupts and software interrupt numbers 8 to 50, 52
to 54 and 57 for the INT instruction use the same interrupt vector table. The peripheral function interrupt is a maskable interrupt.
See Table 10.2 about how the peripheral function interrupt occurs. Refer to the descriptions of each
function for details.
Rev. 1.10 Oct. 18, 2005 Page 81
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
10.4 High-Speed Interrupt
The high-speed interrupt executes an interrupt sequence in five cycles and returns from the interrupt in
three cycles.
When the FSIT bit in the RLVL register is set to "1" (interrupt priority level 7 available for the high-speed
interrupt), the ILVL2 to ILVL0 bits in the interrupt control registers can be set to "1112" (level 7) to use the
high-speed interrupt.
Only one interrupt can be set as the high-speed interrupt. When using the high-speed interrupt, do not set
multiple interrupts to interrupt priority level 7. Set the DMAII bit in the RLVL register to "0" (interrupt priority
level 7 available for interrupts).
Set the starting address of the high-speed interrupt routine in the VCT register.
When the high-speed interrupt is acknowledged, the FLG register is saved into the SVF register and PC is
saved into the SVP register. The program is executed from an address indicated by the VCT register.
Execute the FREIT instruction to return from the high-speed interrupt routine.
The values saved into the SVF and SVP registers are restored to the FLG register and PC by executing the
FREIT instruction.
The high-speed interrupt and the DMA2 and DMA3 use the same register. When using the high-speed
interrupt, neither DMA2 nor DMA3 is available. DMA0 and DMA1 can be used.
10.5 Interrupts and Interrupt Vectors
There are four bytes in one vector. Set the starting address of interrupt routine in each vector table. When
an interrupt request is acknowledged, the interrupt routine is executed from the address set in the interrupt
vectors.
Figure 10.2 shows the interrupt vector.
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
MSB
LSB
Vector Address + 0
Low-order bits of an address
Vector Address + 1
Middle-order bits of an address
Vector Address + 2
High-order bits of an address
Vector Address + 3
0016
Figure 10.2 Interrupt Vector
Rev. 1.10 Oct. 18, 2005 Page 82
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
10.5.1 Fixed Vector Tables
The fixed vector tables are allocated addresses FFFFDC16 to FFFFFF16. Table 10.1 lists the fixed vector
tables. Refer to 24.2 Functions to Prevent Rewriting of Flash Memory for fixed vectors of flash
memory.
Table 10.1 Fixed Vector Table
Interrupt
Generated by
Vector Addresses
Address (L) to Address (H)
Undefined
Instruction
FFFFDC16 to FFFFDF16
Overflow
FFFFE016 to FFFFE316
BRK Instruction
FFFFE416 to FFFFE716
Address Match
FFFFE816 to FFFFEB16
-
FFFFEC16 to FFFFEF16
Remarks
M32C/80 Series
If the content of address FFFFE716 is
Software Manual
FF16, a program is executed from the
address stored into software interrupt
number 0 in the relocatable vector table
Reserved space
These addresses are used for the
Reset,
watchdog timer interrupt and oscillation Clock Generation Circuit,
stop detection interrupt
Watchdog Timer
Watchdog Timer FFFFF016 to FFFFF316
-
FFFFF416 to FFFFF716
NMI
FFFFF816 to FFFFFB16
Reset
FFFFFC16 to FFFFFF16
Reference
Reserved space
Reset
10.5.2 Relocatable Vector Tables
The relocatable vector tables occupy 256 bytes from the starting address set in the INTB register. Table
10.2 lists the relocatable vector tables.
Set an even address as the starting address of the vector table set in the INTB register to increase
interrupt sequence execution rate.
Rev. 1.10 Oct. 18, 2005 Page 83
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
Table 10.2 Relocatable Vector Tables
Interrupt Generated by
Vector Table Address
Address(L) to Address(H)(1)
Software
Reference
Interrupt Number
BRK Instruction(2)
+0 to +3 (000016 to 000316)
0
M32C/80 Series
Reserved Space
+4 to +31 (000416 to 001F16)
1 to 7
Software Manual
DMA0
+32 to +35 (002016 to 002316)
8
DMAC
DMA1
+36 to +39 (002416 to 002716)
9
DMA2
+40 to +43 (002816 to 002B16)
10
DMA3
+44 to +47 (002C16 to 002F16)
11
Timer A0
+48 to +51 (003016 to 003316)
12
Timer A1
+52 to +55 (003416 to 003716)
13
Timer A2
+56 to +59 (003816 to 003B16)
14
Timer A3
+60 to +63 (003C16 to 003F16)
15
+64 to +67 (004016 to 004316)
16
+68 to +71 (004416 to 004716)
17
+72 to +75 (004816 to 004B16)
18
+76 to +79 (004C16 to 004F16)
19
UART1 Reception, ACK (3)
+80 to +83 (005016 to 005316)
20
Timer B0
+84 to +87 (005416 to 005716)
21
Timer B1
+88 to +91 (005816 to 005B16)
22
Timer B2
+92 to +95 (005C16 to 005F16)
23
Timer B3
+96 to +99 (006016 to 006316)
24
Timer B4
+100 to +103 (006416 to 006716)
25
Timer A4
UART0 Transmission,
NACK(3)
UART0 Reception, ACK(3)
UART1 Transmission,
NACK(3)
Timer A
Serial I/O
Timer B
________
INT5
+104 to +107 (006816 to 006B16) 26
Interrupt
________
INT4
+108 to +111 (006C16 to 006F16) 27
________
INT3
+112 to +115 (007016 to 007316)
28
+116 to +119 (007416 to 007716)
29
________
INT2
________
INT1
+120 to +123 (007816 to 007B16) 30
_______
INT0
+124 to +127 (007C16 to 007F16) 31
Timer B5
UART2 Transmission,
NACK(3)
UART2 Reception, ACK(3)
UART3 Transmission,
Timer B
+132 to +135 (008416 to 008716)
33
Serial I/O
+140 to +143 (008C16 to 008F16) 35
NACK(3)
UART4 Reception, ACK(3)
Rev. 1.10 Oct. 18, 2005 Page 84
REJ09B0162-0110
32
+136 to +139 (008816 to 008B16) 34
NACK(3)
UART3 Reception, ACK(3)
UART4 Transmission,
+128 to +131 (008016 to 008316)
+144 to +147 (009016 to 009316)
36
+148 to +151 (009416 to 009716)
37
+152 to +155 (009816 to 009B16) 38
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
Table 10.2 Relocatable Vector Tables (Continued)
Interrupt Generated by
Vector Table Address
Address(L) to Address(H)(1)
Software
Interrupt Number
Bus Conflict Detect, Start Condition Detect, +156 to +159 (009C16 to 009F16) 39
Reference
Serial I/O
Stop Condition Detect (UART2)(3),
Bus Conflict Detect, Start Condition Detect, +160 to +163 (00A016 to 00A316) 40
Stop Condition Detect (UART3/UART0)(4)
Bus Conflict Detect, Start Condition Detect, +164 to +167 (00A416 to 00A716) 41
Stop Condition Detect (UART4/UART1)(4)
A/D0
+168 to +171 (00A816 to 00AB16) 42
A/D Converter
Key Input
+172 to +175 (00AC16 to 00AF16) 43
Interrupts
Intelligent I/O Interrupt 0, CAN 3
+176 to +179 (00B016 to 00B316) 44
Intelligent I/O
Intelligent I/O Interrupt 1, CAN 4
+180 to +183 (00B416 to 00B716) 45
CAN
Intelligent I/O Interrupt 2, CAN 6
+184 to +187 (00B816 to 00BB16) 46
Intelligent I/O Interrupt 3, CAN 7
+188 to +191 (00BC16 to 00BF16) 47
Intelligent I/O Interrupt 4
+192 to +195 (00C016 to 00C316) 48
CAN 5
+196 to +199 (00C416 to 00C716) 49
CAN 8
+200 to +203 (00C416 to 00C716) 50
Reserved Space
+204 to +207 (00C816 to 00CF16) 51
Intelligent I/O Interrupt 8
+208 to +211 (00D016 to 00D316) 52
Intelligent I/O
Intelligent I/O Interrupt 9, CAN 0
+212 to +215 (00D416 to 00D716) 53
CAN
Intelligent I/O Interrupt 10, CAN 1
+216 to +219 (00D816 to 00DB16) 54
Reserved Space
+220 to +227 (00DC16 to 00E316) 55, 56
CAN 2
+228 to +231 (00E416 to 00E716) 57
Reserved Space
+232 to +255 (00E816 to 00FF16) 58 to 63
INT Instruction(2)
+0 to +3 (000016 to 000316) to
0 to 63
CAN
CAN
Interrupts
+252 to +255 (00FC16 to 00FF16)
NOTES:
1. These addresses are relative to those in the INTB register.
2. The I flag does not disable interrupts.
3. In I2C mode, NACK, ACK or start/stop condition detection causes interrupts to be generated.
4. The IFSR6 bit in the IFSR register determines whether these addresses are used for an interrupt in UART0 or in
UART3.
The IFSR7 bit in the IFSR register determines whether these addresses are used for an interrupt in UART1 or in
UART4.
Rev. 1.10 Oct. 18, 2005 Page 85
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
10.6 Interrupt Request Acknowledgement
Software interrupts and special interrupts occur when conditions to generate an interrupt are met.
The peripheral function interrupts are acknowledged when all conditions below are met.
• I flag
= "1"
• IR bit
= "1"
• ILVL2 to ILVL0 bits
> IPL
The I flag, IPL, IR bit and ILVL2 to ILVL0 bits are independent of each other. The I flag and IPL are in the
FLG register. The IR bit and ILVL2 to ILVL0 bits are in the interrupt control register.
10.6.1 I Flag and IPL
The I flag enables or disables maskable interrupts. When the I flag is set to "1" (enable), all maskable
interrupts are enabled; when the I flag is set to "0" (disable), they are disabled. The I flag is automatically
set to "0" after reset.
IPL, consisting of three bits, indicates the interrupt priority level from level 0 to level 7.
If a requested interrupt has higher priority level than indicated by IPL, the interrupt is acknowledged.
Table 10.3 lists interrupt priority levels associated with IPL.
Table 10.3 Interrupt Priority Levels
IPL2
IPL1
IPL0
Interrupt Priority Levels
0
0
0
Level 1 and above
0
0
1
Level 2 and above
0
1
0
Level 3 and above
0
1
1
Level 4 and above
1
0
0
Level 5 and above
1
0
1
Level 6 and above
1
1
0
Level 7 and above
1
1
1
All maskable interrupts are disabled
10.6.2 Interrupt Control Register and RLVL Register
The peripheral function interrupts use interrupt control registers to control each interrupt. Figures 10.3
and 10.4 show the interrupt control register. Figure 10.5 shows the RLVL register.
Rev. 1.10 Oct. 18, 2005 Page 86
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
Interrupt Control Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
TA0IC to TA4IC
TB0IC to TB5IC
S0TIC to S4TIC
S0RIC to S4RIC
Address
006C16, 008C16, 006E16, 008E16, 007016
009416, 007616, 009616, 007816, 009816, 006916
BCN0IC to BCN4IC
DM0IC to DM3IC
009016, 009216, 008916, 008B16, 008D16
007216, 007416, 006B16, 006D16, 006F16
007116, 009116, 008F16, 007116(1), 009116(2)
006816, 008816, 006A16, 008A16
AD0IC
KUPIC
IIO0IC to IIO4IC
007316
009316
007516, 009516, 007716, 009716, 007916
IIO8IC to IIO10IC
CAN0IC to CAN2IC
007D16, 009D16, 007F16
009D16, 007F16, 008116(3)
007516, 009516, 009916(3)
CAN3IC to CAN5IC
CAN6IC to CAN8IC
Bit
Symbol
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
XXXX X0002
007716, 009716, 007B16(3)
Bit Name
After Reset
XXXX X0002
Function
RW
b2b1b0
ILVL0
ILVL1
Interrupt Priority Level
Select Bit
ILVL2
IR
Interrupt Request Bit
0 0 0: Level 0 (interrupt disabled)
0 0 1: Level 1
0 1 0: Level 2
0 1 1: Level 3
1 0 0: Level 4
1 0 1: Level 5
1 1 0: Level 6
1 1 1: Level 7
0: requests no interrupt
1: requests an interrupt(4)
Nothing is assigned. When write, set to "0".
(b7 - b4) When read, its content is indeterminate.
NOTES:
1. The BCN0IC register shares an address with the BCN3IC register.
2. The BCN1IC register shares an address with the BCN4IC register.
3. The IIO9IC register shares an address with the CAN0IC register.
The IIO10IC register shares an address with the CAN1IC register.
The IIO0IC register shares an address with the CAN3IC register.
The IIO1IC register shares an address with the CAN4IC register.
The IIO2IC register shares an address with the CAN6IC register.
The IIO3IC register shares an address with the CAN7IC register.
4. The IR bit can be set to only "0" (do not set to "1").
Figure 10.3 Interrupt Control Register (1)
Rev. 1.10 Oct. 18, 2005 Page 87
REJ09B0162-0110
of 435
RW
RW
RW
RW
10. Interrupts
M32C/88 Group (M32C/88T)
Interrupt Control Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
INT0IC to INT2IC
INT3IC to INT5IC
Bit
Symbol
Address
009E16, 007E16, 009C16
After Reset
XX00 X0002
007C16, 009A16, 007A16
XX00 X0002
Bit Name
Function
RW
b2b1b0
ILVL0
ILVL1
Interrupt Priority Level
Select Bit
ILVL2
0 0 0: Level 0 (interrupt disabled)
0 0 1: Level 1
0 1 0: Level 2
0 1 1: Level 3
1 0 0: Level 4
1 0 1: Level 5
1 1 0: Level 6
1 1 1: Level 7
RW
RW
RW
Interrupt Request Bit
0: requests no interrupt
1: requests an interrupt(1)
RW
POL
Polarity Switch Bit
0: Selects falling edge or "L"(2)
1: Selects rising edge or "H"
RW
LVS
Level Sensitive/Edge
Sensitive Switch Bit
0: Edge sensitive
1: Level sensitive(3)
RW
IR
(b7 - b6)
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
NOTES:
1. The IR bit can be set to only "0" (do not set to "1").
2. Set the POL bit to "0" when a corresponding bit in the IFSR register is set to "1" (both edges).
3. When setting the LVS bit to "1" , set a corresponding bit in the IFSR register to "0" (one edge).
Figure 10.4 Interrupt Control Register (2)
10.6.2.1 ILVL2 to ILVL0 Bits
The ILVL2 to ILVL0 bits determines an interrupt priority level. The higher the interrupt priority level is,
the higher interrupt priority is.
When an interrupt request is generated, its interrupt priority level is compared to IPL. This interrupt is
acknowledged only when its interrupt priority level is higher than IPL. When the ILVL2 to ILVL0 bits
are set to "0002" (level 0), its interrupt is ignored.
10.6.2.2 IR Bit
The IR bit is automatically set to "1" (interrupt requested) when an interrupt request is generated. The
IR bit is automatically set to "0" (no interrupt requested) after an interrupt request is acknowledged and
an interrupt routine in the corresponding interrupt vector is executed.
The IR bit can be set to "0" by program. Do not set to "1".
Rev. 1.10 Oct. 18, 2005 Page 88
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
Exit Priority Register
b7
b6
b5
b4
b3
b2
b1
Symbol
RLVL
b0
Bit
Symbol
RLVL0
RLVL1
RLVL2
Address
009F16
After Reset
XXXX 00002
Bit Name
Function
b2b1b0
0 0 0 : Level 0
0 0 1 : Level 1
Stop/Wait Mode Exit
0 1 0 : Level 2
Minimum Interrupt Priority 0 1 1 : Level 3
1 0 0 : Level 4
Level Control Bit(1)
1 0 1 : Level 5
1 1 0 : Level 6
1 1 1 : Level 7
0: Interrupt priority level 7 is used
for normal interrupt
1: Interrupt priority level 7 is used
for high-speed interrupt
FSIT
High-Speed Interrupt
Set Bit(2)
(b4)
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
DMAII
DMA II Select Bit(4)
0: Interrupt priority level 7 is used
for interrupt
1: Interrupt priority level 7 is used
for DMA II transfer(3)
RW
RW
RW
RW
RW
RW
Nothing is assigned. When write, set to "0".
(b7 - b6) When read, its content is indeterminate.
NOTES:
1. The microcomputer exits stop or wait mode when the requested interrupt priority level is higher than
the level set in the RLVL2 to RLVL0 bits. Set the RLVL2 to RLVL0 bits to the same value as IPL in
the FLG register.
2. When the FSIT bit is set to "1", an interrupt having the interrupt priority level 7 becomes the high-speed
interrupt. In this case, set only one interrupt to the interrupt priority level 7 and the DMAII bit to "0".
3. Set the ILVL2 to ILVL0 bits in the interrupt control register after setting the DMAII bit to "1".
Do not change the DMAII bit setting to "0" after setting the DMAII bit to "1". Set the FSIT bit to "0"
when the DMAII bit to "1".
4. The DMAII bit becomes indeterminate after reset. To use the DMAII bit for an interrupt setting, set it
to "0" before setting the interrupt control register.
Figure 10.5 RLVL Register
10.6.2.3 RLVL2 to RLVL0 Bits
When using an interrupt to exit stop or wait mode, refer to 8.5.2 Wait Mode and 8.5.3 Stop Mode for
details.
Rev. 1.10 Oct. 18, 2005 Page 89
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
10.6.3 Interrupt Sequence
The interrupt sequence is performed between an interrupt request acknowledgment and interrupt routine
execution.
When an interrupt request is generated while an instruction is executed, the CPU determines its interrupt
priority level after the instruction is completed. The CPU starts the interrupt sequence from the following
cycle. However, in regards to the SCMPU, SIN, SMOVB, SMOVF, SMOVU, SSTR, SOUT or RMPA
instruction, if an interrupt request is generated while executing the instruction, the microcomputer suspends the instruction to start the interrupt sequence.
The interrupt sequence is performed as follows:
(1) The CPU obtains interrupt information (interrupt number and interrupt request level) by reading
address 00000016 (address 00000216 for the high-speed interrupt). Then, the IR bit applicable to
the interrupt information is set to "0" (interrupt requested).
(2) The FLG register, prior to an interrupt sequence, is saved to a temporary register(1) within the CPU.
(3) Each bit in the FLG register is set as follows:
• The I flag is set to "0" (interrupt disabled)
• The D flag is set to "0" (single-step disabled)
• The U flag is set to "0" (ISP selected)
(4) A temporary register within the CPU is saved to the stack; or to the SVF register for the high-speed
interrupt.
(5) PC is saved to the stack; or to the SVP register for the high-speed interrupt.
(6) The interrupt priority level of the acknowledged interrupt is set in IPL .
(7) A relocatable vector corresponding to the acknowledged interrupt is stored into PC.
After the interrupt sequence is completed, an instruction is executed from the starting address of the
interrupt routine.
NOTE:
1. Temporary register cannot be modified by users.
Rev. 1.10 Oct. 18, 2005 Page 90
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
10.6.4 Interrupt Response Time
Figure 10.6 shows an interrupt response time. Interrupt response time is the period between an interrupt
generation and the execution of the first instruction in an interrupt routine. Interrupt response time includes the period between an interrupt request generation and the completed execution of an instruction
((a) on Figure 10.6) and the period required to perform an interrupt sequence ((b) on Figure 10.6).
Interrupt request is generated
Interrupt request is acknowledged
Time
Instruction
(a)
Interrupt sequence
Instruction in
interrupt routine
(b)
Interrupt response time
(a) Period between an interrupt request generation and the completed execution of an instruction.
(b) Period required to perform an interrupt sequence.
Figure 10.6 Interrupt Response Time
Time (a) varies depending on an instruction being executed. The DIV, DIVX and DIVU instructions
require the longest time (a); 42 cycles when an immediate value or register is set as the divisor.
When the divisor is a value in the memory, the following value is added.
• Normal addressing
:2+X
• Index addressing
:3+X
• Indirect addressing
: 5 + X + 2Y
• Indirect index addressing
: 6 + X + 2Y
X is the number of wait states for a divisor space. Y is the number of wait states for the space that stores
indirect addresses. If X and Y are in an odd address or in 8-bit bus space, the X and Y value must be
doubled.
Table 10.4 lists time (b), shown Figure 10.6.
Rev. 1.10 Oct. 18, 2005 Page 91
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
Table 10.4 Interrupt Sequence Execution Time
Interrupt
Interrupt Vector Address
Peripheral Function
16-Bit Bus
8-Bit Bus
Even address
14 cycles
16 cycles
Odd address(1)
16 cycles
16 cycles
Even address
12 cycles
14 cycles
Odd address(1)
14 cycles
14 cycles
Even address(2)
13 cycles
15 cycles
Overflow
Even address(2)
14 cycles
16 cycles
BRK Instruction (relocatable vector table)
Even address
17 cycles
19 cycles
Odd address(1)
19 cycles
19 cycles
BRK Instruction (fixed vector table)
Even address(2)
19 cycles
21 cycles
High-Speed Interrupt
Vector table is internal register
5 cycles
INT Instruction
_______
NMI
Watchdog Timer
Undefined Instruction
Address Match
NOTES:
1. Allocate interrupt vectors in even addresses.
2. Vectors are fixed to even addresses.
10.6.5 IPL Change when Interrupt Request is Acknowledged
When a peripheral function interrupt request is acknowledged, IPL sets the priority level for the acknowledged interrupt.
Software interrupts and special interrupts have no interrupt priority level. If an interrupt request that has
no interrupt priority level is acknowledged, the value shown in Table 10.5 is set in IPL as the interrupt
priority level.
Table 10.5 Interrupts without Interrupt Priority Levels and IPL
Interrupt Source
Level Set to IPL
_______
Watchdog Timer, NMI, Oscillation Stop Detection
7
Reset
0
Software, Address Match
Rev. 1.10 Oct. 18, 2005 Page 92
REJ09B0162-0110
Not changed
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
10.6.6 Saving a Register
In the interrupt sequence, the FLG register and PC are saved to the stack.
After the FLG register is saved to the stack, 16 high-order bits and 16 low-order bits of PC, extended to 32
bits, are saved to the stack. Figure 10.7 shows stack states before and after an interrupt request is
acknowledged.
Other important registers are saved by program at the beginning of an interrupt routine. The PUSHM
instruction can save several registers(1) in the register bank used.
Refer to 10.4 High-Speed Interrupt for the high-speed interrupt.
NOTE:
1. Can be selected from the R0, R1, R2, R3, A0, A1, SB and FB registers.
Address
The Stack
Address
LSB
MSB
m-6
The Stack
MSB
m-6
LSB
PCL
PCM
m-5
m-5
m–4
m–4
PCH
m–3
m–3
0016
m–2
m–2
FLGL
m–1
m–1
m
Content of
previous stack
m+1
Content of
previous stack
[SP]
SP value before
an interrupt is
generated
m
m+1
Stack state before an interrupt request is acknowledged
[SP]
New SP value
FLGH
Content of
previous stack
Content of
previous stack
Stack state after an interrupt request is acknowledged
Figure 10.7 Stack States
10.6.7 Restoration from Interrupt Routine
When the REIT instruction is executed at the end of an interrupt routine, the FLG register and PC before the
interrupt sequence is performed, which have been saved to the stack, are automatically restored. The program, executed before an interrupt request was acknowledged, starts running again. Refer to 10.4 HighSpeed Interrupt for the high-speed interrupt.
Restore registers saved by program in an interrupt routine by the POPM instruction or others before the
REIT and FREIT instructions. Register bank is switched back to the bank used prior to the interrupt
sequence by the REIT or FREIT instruction.
Rev. 1.10 Oct. 18, 2005 Page 93
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
10.6.8 Interrupt Priority
If two or more interrupt requests are sampled at the same sampling points (a timing to detect whether an
interrupt request is generated or not), the interrupt with the highest priority is acknowledged.
Set the ILVL2 to ILVL0 bits to select the desired priority level for maskable interrupts (peripheral function
interrupt).
Priority levels of special interrupts such as reset (reset has the highest priority) and watchdog timer are
set by hardware. Figure 10.8 shows priority levels of hardware interrupts.
The interrupt priority does not affect software interrupts. Executing instruction causes the microcomputer
to execute an interrupt routine.
_______
Reset > NMI >
Oscillation Stop Detection > Peripheral Function > Address Match
Watchdog Timer
Figure 10.8 Interrupt Priority
10.6.9 Interrupt Priority Level Select Circuit
The interrupt priority level select circuit selects the highest priority interrupt when two or more interrupt
requests are sampled at the same sampling point.
Figure 10.9 shows the interrupt priority level select circuit.
Rev. 1.10 Oct. 18, 2005 Page 94
REJ09B0162-0110
of 435
10. Interrupts
M32C/88 Group (M32C/88T)
Hig
h
Each Interrupt Priority Level
Level 0 (Initial Value)
DMA0
DMA1
DMA2
DMA3
Each Interrupt Priority Level
Timer A0
A/D0
Timer A1
Key Input Interrupt
Timer A2
Intelligent I/O Interrupt 0
/CAN Interrupt 3
Timer A3
Intelligent I/O Interrupt 1
/CAN Interrupt 4
Timer A4
UART0 Transmission/NACK
Intelligent I/O Interrupt 2
/CAN Interrupt 6
UART0 Reception/ACK
Intelligent I/O Interrupt 3
/CAN Interrupt 7
UART1 Transmission/NACK
Intelligent I/O Interrupt 4
UART1 Reception/ACK
CAN Interrupt 5
Timer B0
CAN Interrupt 8
Timer B1
Intelligent I/O Interrupt 8
Timer B2
Intelligent I/O Interrupt 9
/CAN Interrupt 0
Timer B3
Intelligent I/O Interrupt 10
/CAN Interrupt 1
Timer B4
CAN Interrupt 2
INT5
RLVL2 to RLVL0 Bits
INT4
Interrupt request priority
detection results output
(to clock generation circuit)
INT3
INT2
IPL
INT1
INT0
I Flag
Timer B5
Address Match
Watchdog Timer,
Oscillation Stop Detection
UART2 Transmission/NACK
NMI
UART2 Reception/ACK
DMAC II
UART3 Transmission/NACK
UART3 Reception/ACK
UART4 Transmission/NACK
UART4 Reception/ACK
Bus Conflict/Start, Stop
Condition(UART2)
Bus Conflict/Start, Stop Condition
(UART0, UART3)
Bus Conflict/Start, Stop Condition
(UART1, UART4)
Low
Peripheral Function Interrupt Priority
(if priority levels are the same)
Figure 10.9 Interrupt Priority Level Select Circuit
Rev. 1.10 Oct. 18, 2005 Page 95
REJ09B0162-0110
of 435
Interrupt request
acknowledged
(to CPU)
10. Interrupts
M32C/88 Group (M32C/88T)
______
10.7 INT Interrupt
______
External input generates the INTi interrupt (i = 0 to 5). The LVS bit in the INTiIC register selects either edge
sensitive triggering to generate an interrupt on any edge or level sensitive triggering to generate an interrupt at an applied signal level. The POL bit in the INTiIC register determines the polarity.
For edge sensitive, when the IFSRi bit in the IFSR register is set to "1", an interrupt occurs on both rising
and falling edges of the external input. If the IFSRi bit is set to "1", set the POL bit in the corresponding
register to "0" (falling edge).
_______
For level sensitive, set the IFSRi bit to "0" (single edge). When the INTi pin input level reaches the level set
_______
in the POL bit, the IR bit in the INTiIC register is set to "1". The IR bit remains unchanged even if the INTi
_______
pin level is changed. The IR bit is set to "0" when the INTi interrupt is acknowledged or when the IR bit is
written to "0" by program.
Figure 10.10 shows the IFSR register.
External Interrupt Request Source Select Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
IFSR
Address
031F16
After Reset
0016
Bit
Symbol
Bit Name
IFSR0
INT0 Interrupt Polarity
Select Bit(1)
0: One edge
1: Both edges
RW
IFSR1
INT1 Interrupt Polarity
Select Bit(1)
0: One edge
1: Both edges
RW
IFSR2
INT2 Interrupt Polarity
Select Bit(1)
0: One edge
1: Both edges
RW
IFSR3
INT3 Interrupt Polarity
Select Bit(1)
0: One edge
1: Both edges
RW
IFSR4
INT4 Interrupt Polarity
select bit(1)
0: One edge
1: Both edges
RW
IFSR5
INT5 Interrupt Polarity
Select Bit(1)
0: One edge
1: Both edges
RW
IFSR6
UART0, UART3
Interrupt Source
Select Bit
0: UART3 bus conflict, start condition
detect, stop condition detect
RW
1: UART0 bus conflict, start condition
detect, stop condition detect
IFSR7
UART1, UART4
Interrupt Source
Select Bit
0: UART4 bus conflict, start condition
detect, stop condition detect
RW
1: UART1 bus conflict, start condition
detect, stop condition detect
Function
NOTE:
1. Set this bit to "0" to select a level-sensitive triggering.
When setting this bit to "1", set the POL bit in the INTilC register (i = 0 to 5) to "0" (falling edge).
Figure 10.10 IFSR Register
Rev. 1.10 Oct. 18, 2005 Page 96
REJ09B0162-0110
of 435
RW
10. Interrupts
M32C/88 Group (M32C/88T)
______
10.8 NMI Interrupt
______
______
The NMI interrupt(1) occurs when a signal applied to the NMI pin changes from a high-level ("H") signal to a
______
______
low-level ("L") signal. The NMI interrupt is a non-maskable interrupt. Although the P85/NMI pin is used as
______
the NMI interrupt input pin, the P8_5 bit in the P8 register indicates the input level for this pin.
NOTE:
______
______
______
1. When the NMI interrupt is not used, connect the NMI pin to VCC via a resistor. Because the NMI
interrupt cannot be ignored, the pin must be connected.
10.9 Key Input Interrupt
Key input interrupt request is generated when one of the signals applied to the P104 to P107 pins in input
mode is on the falling edge. The key input interrupt can be also used as key-on wake-up function to exit wait
or stop mode. To use the key input interrupt, do not use P104 to P107 as A/D input ports. Figure 10.11
shows a block diagram of the key input interrupt. When an "L" signal is applied to any pins in input mode,
signals applied to other pins are not detected as an interrupt request signal.
When the PSC_7 bit in the PSC register(2) is set to "1" (key input interrupt disabled), no key input interrupt
occurs regardless of interrupt control register settings. When the PSC_7 bit is set to "1", no input from a
port pin is available even when in input mode.
NOTE:
2. Refer to 23. Programmable I/O Ports about the PSC register.
PU31 Bit in the
PUR3 Register
Pull-up
Transistor
PD10_7 Bit
PSC_7 Bit
KUPIC Register
PD10_7 Bit
P107/KI3
Pull-up
Transistor
PD10_6 Bit
Interrupt Control
Circuit
P106/KI2
Pull-up
Transistor
PD10_5 Bit
P105/KI1
Pull-up
Transistor
PD10_4 Bit
P104/KI0
Figure 10.11 Key Input Interrupt
Rev. 1.10 Oct. 18, 2005 Page 97
REJ09B0162-0110
of 435
Key Input Interrupt
Request
10. Interrupts
M32C/88 Group (M32C/88T)
10.10 Address Match Interrupt
The address match interrupt occurs immediately before executing an instruction that is stored into an address indicated by the RMADi register (i=0 to 7). The address match interrupt can be set in eight addresses. The AIERi bit in the AIER register determines whether the interrupt is enabled or disabled. The I
flag and IPL do not affect the address match interrupt.
Figure 10.12 shows registers associated with the address match interrupt.
The starting address of an instruction must be set in the RMADi register. The address match interrupt does
not occur when a table data or addresses other than the starting address of the instruction is set.
Address Match Interrupt Enable Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
AIER
Bit
Symbol
Address
000916
After Reset
0000 00002
Function
Bit Name
RW
AIER0
Address Match
Interrupt 0 Enable Bit
0: Disables an interrupt
1: Enables an interrupt
RW
AIER1
Address Match
Interrupt 1 Enable Bit
0: Disables an interrupt
1: Enables an interrupt
RW
AIER2
Address Match
Interrupt 2 Enable Bit
0: Disables an interrupt
1: Enables an interrupt
RW
AIER3
Address Match
Interrupt 3 Enable Bit
0: Disables an interrupt
1: Enables an interrupt
RW
AIER4
Address Match
Interrupt 4 Enable Bit
0: Disables an interrupt
1: Enables an interrupt
RW
AIER5
Address Match
Interrupt 5 Enable Bit
0: Disables an interrupt
1: Enables an interrupt
RW
AIER6
Address Match
Interrupt 6 Enable Bit
0: Disables an interrupt
1: Enables an interrupt
RW
AIER7
Address Match
Interrupt 7 Enable Bit
0: Disables an interrupt
1: Enables an interrupt
RW
Address Match Interrupt Register i (i=0 to 7)
b23
b16 b15
b8 b7
b0
Symbol
RMAD0
RMAD1
RMAD2
RMAD3
RMAD4
RMAD5
RMAD6
RMAD7
Address
001216 - 001016
001616 - 001416
001A16 - 001816
001E16 - 001C16
002A16 - 002816
002E16 - 002C16
003A16 - 003816
003E16 - 003C16
Function
Addressing Register for Address Match Interrupt
Figure 10.12 AIER Register and RMAD0 to RMAD7 Registers
Rev. 1.10 Oct. 18, 2005 Page 98
REJ09B0162-0110
of 435
After Reset
00000016
00000016
00000016
00000016
00000016
00000016
00000016
00000016
Setting Range
RW
00000016 to FFFFFF16
RW
10. Interrupts
M32C/88 Group (M32C/88T)
10.11 Intelligent I/O Interrupt and CAN Interrupt
The intelligent I/O interrupt and CAN interrupt are assigned to software interrupt numbers 44 to 50, 52 to 54,
and 57.
When using the intelligent I/O interrupt or CAN interrupt, set the IRLT bit in the IIOiIE register (i = 0 to 6, 8
to 11) to "1" (interrupt request for interrupt used).
Various interrupt requests cause the intelligent I/O interrupt to occur. When an interrupt request is generated with each intelligent I/O or CAN functions, the corresponding bit in the IIOiIR register is set to "1"
(interrupt requested). When the corresponding bit in the IIOiIE register is set to "1" (interrupt enabled), the
IR bit in the corresponding IIOiIC register is set to "1" (interrupt requested).
After the IR bit setting changes "0" to "1", the IR bit remains set to "1" when a bit in the IIOiIR register is set
to "1" by another interrupt request and the corresponding bit in the IIOiIE register is set to "1".
Bits in the IIOiIR register are not set to "0" automatically, even if an interrupt is acknowledged. Set each bit
to "0" by program. If these bit settings are left "1", all generated interrupt requests are ignored.
Figure 10.13 shows a block diagram of the intelligent I/O interrupt and CAN interrupt. Figure 10.14 shows
the IIOiIR register. Figure 10.15 shows the IIOiIE register.
IIOiIR Register(2)
IRLT Bit in the
IIOiIE Register
0
Bit 1
1
Interrupt Request(1)
Intelligent I/O Interrupt i Request
0
Bit 2
1
Interrupt Request(1)
0
Bit 7
1
Interrupt Request(1)
IIOiIE Register(3)
Bit 1
NOTES:
1. See Figures 10.14 and 10.15 about bits 1 to 7 in the
IIOiIR register and bits 1 to 7 in the IIOiIE register.
2. Bits 1 to 7 in the IIOiIR register are not set to "0"
automatically even if an interrupt request is
generated. Set to "0" by program.
3. Do not change the IRLT bit and the interrupt enable bit
in the IIOiIE register simultaneously.
Bit 2
Bit 7
i= 0 to 6, 8 to 11
Figure 10.13 Intelligent I/O Interrupt and CAN Interrupt
Rev. 1.10 Oct. 18, 2005 Page 99
REJ09B0162-0110
of 435
M32C/88 Group (M32C/88T)
10. Interrupts
The CANjk (j=0 to 2, k=0 to 2) interrupt and CANn (n=1, 2) wake-up interrupt are provided as the
CAN interrupt. The following registers are required for the CAN interrupts:
• Bits 7 in the IIO9IR to IIO11IR registers and bits 7 in the IIO9IE to IIO11IE registers for the CAN00 to
CAN02 interrupts.
• Bits 7 in the IIO0IR, IIO1IR and IIO5IR registers and bits 7 in the IIO0IE, IIO1IE and IIO5IE registers for
the CAN10 to CAN12 interrupts.
• Bits 7 in the IIO2IR, IIO3IR and IIO6IR registers and bits 7 in the IIO2IE, IIO3IE and IIO6IE registers for
the CAN20 to CAN22 interrupts.
• Bit 6 in the IIO5IR register and bit 6 in the IIO5IE register for the CAN1 wake-up interrupt.
• Bit 6 in the IIO6IR register and bit 6 in the IIO6IE register for the CAN2 wake-up interrupt.
The CAN0IC, CAN1IC, CAN3IC, CAN4IC CAN6IC, and CAN7IC registers share addresses with the following registers:
• The CAN0IC register shares an address with the IIO9IC register.
• The CAN1IC register shares an address with the IIO10IC register.
• The CAN3IC register shares an address with the IIO0IC register.
• The CAN4IC register shares an address with the IIO1IC register.
• The CAN6IC register shares an address with the IIO2IC register.
• The CAN7IC register shares an address with the IIO3IC register.
Refer to 22.4 CAN Interrupt for details.
When using the intelligent I/O interrupt or CAN interrupt to activate DMAC II, set the IRLT bit in the IIOiIE
register to "0" (interrupt used for DMAC, DMAC II) to enable the interrupt request that the IIOiIE (i=0 to 6, 8
to 11) register requires.
Rev. 1.10 Oct. 18, 2005 Page 100 of 435
REJ09B0162-0110
10. Interrupts
M32C/88 Group (M32C/88T)
Interrupt Request Register
b7
b6
b5
b4
b3
b2
b1
b0
0
Symbol
Address
After Reset
IIO0IR to IIO6IR, IIO8IR to IIO11IR
See below
0000 000X2
Bit
Symbol
RW
Function
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
(b0)
(Note 1)
0: requests no interrupt
1: requests an interrupt(2)
RW
(Note 1)
0: requests no interrupt
1: requests an interrupt(2)
RW
Reserved bit. Set to "0".
When read, its content is indeterminate.
RW
(Note 1)
0: requests no interrupt
1: requests an interrupt(2)
RW
(Note 1)
0: requests no interrupt
1: requests an interrupt(2)
RW
(Note 1)
0: requests no interrupt
1: requests an interrupt(2)
RW
(Note 1)
0: requests no interrupt
1: requests an interrupt(2)
RW
(b3)
NOTES:
1. See table below for bit symbols.
2. Only "0" can be set (nothing is changed even if "1" is set).
Bit Symbols for the Interrupt Request Register
Symbol
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
IIO0IR
00A016
CAN10R
-
SIO0RR
G0RIR
-
TM13R/PO13R
-
-
IIO1IR
00A116
CAN11R
-
SIO0TR
G0TOR
-
TM14R/PO14R
-
-
IIO2IR
00A216
CAN20R
-
SIO1RR
G1RIR
-
TM12R/PO12R
-
-
IIO3IR
00A316
CAN21R
-
SIO1TR
G1TOR
-
TM10R/PO10R
-
-
IIO4IR
00A416
SRT0R
SRT1R
-
BT1R
-
TM17R/PO17R
-
-
IIO5IR
00A516
CAN12R CAN1WUR
-
-
-
-
-
-
IIO6IR
00A616
CAN22R CAN2WUR
-
-
-
-
-
-
IIO8IR
00A816
-
-
-
-
-
-
TM11R/PO11R
-
IIO9IR
00A916
CAN00R
-
-
-
-
-
TM15R/PO15R
-
IIO10IR
00AA16
CAN01R
-
-
-
-
-
TM16R/PO16R
-
IIO11IR
00AB16
CAN02R
-
-
-
-
-
-
-
BT1R
: Intelligent I/O Base Timer Interrupt Request
TM1jR
PO1jR
SIOiRR
: Intelligent I/O Time Measurement j Interrupt Request
: Intelligent I/O Waveform Generating Function j Interrupt Request
: Intelligent I/O Communication Unit i Receive Interrupt Request
SIOiTR
GiTOR
: Intelligent I/O Communication Unit i Transmit Interrupt Request
: Intelligent I/O Communication Unit i HDLC Data Processing Function Interrupt Request (TO: Output to Transmit)
GiRIR
SRTiR
CANkmR
: Intelligent I/O Communication Unit i HDLC Data Processing Function Interrupt Request (RI: Input to Receive)
: Intelligent I/O Special Communication Function Interrupt Request
: CANk Communication Function Interrupt Request (k=0 to 2, m=0 to 2)
i=0, 1
CANnWUR : CANn Wake-up Interrupt Request (n=1, 2)
j=0 to 7
: Reserved Bit. Set to "0".
Figure 10.14 IIO0IR to IIO6IR, IIO8IR to IIO11IR Registers
Rev. 1.10 Oct. 18, 2005 Page 101 of 435
REJ09B0162-0110
10. Interrupts
M32C/88 Group (M32C/88T)
Interrupt Enable Register
b7
b6
b5
b4
b3
b2
b1
b0
0
Symbol
Address
After Reset
IIO0IE to IIO6IE, IIO8IE to IIO11IE
See below
0016
Bit
Symbol
IRLT
Bit Name
RW
Function
Interrupt Request
0: Interrupt request is used for DMAC, DMAC II
Select Bit(2)
1: Interrupt request is used for interrupt
0: Disables an interrupt by bit 1 in IIOiIR register
(Note 1)
1: Enables an interrupt by bit 1 in IIOiIR register
0: Disables an interrupt by bit 2 in IIOiIR register
(Note 1)
1: Enables an interrupt by bit 2 in IIOiIR register
Reserved Bit
Set to "0"
RW
RW
RW
(b3)
0: Disables an interrupt by bit 4 in IIOiIR register
(Note 1)
RW
1: Enables an interrupt by bit 4 in IIOiIR register
RW
(Note 1)
0: Disables an interrupt by bit 5 in IIOiIR register
RW
1: Enables an interrupt by bit 5 in IIOiIR register
(Note 1)
0: Disables an interrupt by bit 6 in IIOiIR register
RW
1: Enables an interrupt by bit 6 in IIOiIR register
0: Disables an interrupt by bit 7 in IIOiIR register
(Note 1)
1: Enables an interrupt by bit 7 in IIOiIR register
RW
NOTES:
1. See table below for bit symbols.
2. If an interrupt request is used for interrupt, set bits 1, 2, 4 to 7 to "1" after the IRLT bit is set to "1".
Bit Symbols for the Interrupt Enable Register
Symbol
Address
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
IIO0IE
00B016
CAN10E
-
SIO0RE
G0RIE
-
TM13E/PO13E
-
IRLT
IIO1IE
00B116
CAN11E
-
SIO0TE
G0TOE
-
TM14E/PO14E
-
IRLT
IIO2IE
00B216
CAN20E
-
SIO1RE
G1RIE
-
TM12E/PO12E
-
IRLT
IIO3IE
00B316
CAN21E
-
SIO1TE
G1TOE
-
TM10E/PO10E
-
IRLT
IIO4IE
00B416
SRT0E
SRT1E
-
BT1E
-
TM17E/PO17E
-
IRLT
IIO5IE
00B516
CAN12E CAN1WUE
-
-
-
-
-
IRLT
IIO6IE
00B616
CAN22E CAN2WUE
-
-
-
-
-
IRLT
IIO8IE
00B816
-
-
-
-
-
-
TM11E/PO11E
IRLT
IIO9IE
00B916
CAN00E
-
-
-
-
-
TM15E/PO15E
IRLT
IIO10IE
00BA16
CAN01E
-
-
-
-
-
TM16E/PO16E
IRLT
IIO11IE
00BB16
CAN02E
-
-
-
-
-
-
IRLT
BT1E
TM1jE
PO1jE
SIOiRE
SIOiTE
GiTOE
GiRIE
SRTiE
CANkmE
CANnWUE
-
: Intelligent I/O Base Timer Interrupt Enabled
: Intelligent I/O Time Measurement j Interrupt Enabled
: Intelligent I/O Waveform Generating Function j Interrupt Enabled
: Intelligent I/O Communication Unit i Receive Interrupt Enabled
: Intelligent I/O Communication Unit i Transmit Interrupt Enabled
: Intelligent I/O Communication Unit i HDLC Data Processing Function Interrupt Enabled (TO: Output to Transmit)
: Intelligent I/O Communication Unit i HDLC Data Processing Function Interrupt Enabled (RI: Input to Receive)
: Intelligent I/O Special Communication Function Interrupt Enabled
: CANk Communication Function Interrupt Enabled (k=0 to 2, m=0 to 2)
i=0, 1
: CANn Wake-up Interrupt Enabled (n=1, 2)
j=0 to 7
: Reserved Bit. Set to "0".
Figure 10.15 IIO0IE to IIO6IE, IIO8IE to IIO11IE Registers
Rev. 1.10 Oct. 18, 2005 Page 102 of 435
REJ09B0162-0110
11. Watchdog Timer
M32C/88 Group (M32C/88T)
11. Watchdog Timer
The watchdog timer monitors the program executions and detects defective program. It allows the microcomputer to trigger a reset or to generate an interrupt if the program error occurs. The watchdog timer
contains a 15-bit counter, which is decremented by the CPU clock that the prescaler divides. The CM06 bit
in the CM0 register determines whether a watchdog timer interrupt request or reset is generated if the
watchdog timer underflows. The CM06 bit can only be set to "1" (reset). Once the CM06 bit is set to "1", it
cannot be changed to "0" ( watchdog timer interrupt) by program. The CM06 bit is set to "0" only after reset.
When the main clock, on-chip oscillator clock, or PLL clock runs as the CPU clock, the WDC7 bit in the
WDC register determine whether the prescaler divides the clock by 16 or by 128. When the sub clock runs
as the CPU clock, the prescaler divides the clock by 2 regardless of the WDC7 bit setting. Watchdog timer
cycle is calculated as follows. Marginal errors, due to the prescaler, may occur in watchdog timer cycle.
When the main clock, on-chip oscillator clock, or PLL clock is selected as the CPU clock,
Watchdog timer cycle =
Divide-by-16 or -128 prescaler x counter value of watchdog timer (32768)
CPU clock
When the sub clock is selected as the CPU clock,
Watchdog timer cycle =
Divide-by-2 prescaler x counter value of watchdog timer (32768)
CPU clock
For example, if the CPU clock frequency is 30MHz and the prescaler divides it by 16, the watchdog timer
cycle is approximately 17.5 ms.
The watchdog timer is reset when the WDTS register is set and when a watchdog timer interrupt request is
generated. The prescaler is reset only when the microcomputer is reset. Both watchdog timer and prescaler
stop after reset. They begin counting when the WDTS register is set.
The watchdog timer and prescaler stop in stop mode, wait mode and hold state. They resume counting
from the value held when the mode or state is exited.
Figure 11.1 shows a block diagram of the watchdog timer. Figure 11.2 shows registers associated with the
watchdog timer.
Prescaler
1/16
CPU Clock
1/128
CM07 = 0
WDC7 = 0
CM07 = 0
WDC7 = 1
PM22 = 0
CM06 = 0
HOLD Signal
Watchdog Timer
Interrupt Request
CM07 = 1
Watchdog Timer
1/2
Reset
CM06 = 1
On-chip Oscillator Clock
Write to WDTS Register
Internal Reset Signal
CM06, CM07: Bits in the CM0 Register
WDC7: Bit in the WDC Register
PM22: Bit in the PM2 Register
Figure 11.1 Watchdog Timer Block Diagram
Rev. 1.10 Oct. 18, 2005 Page 103 of 435
REJ09B0162-0110
PM22 = 1
Set to
7FFF16
11. Watchdog Timer
M32C/88 Group (M32C/88T)
Watchdog Timer Control Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
WDC
0
Address
000F16
Bit
Symbol
(b4 - b0)
WDC5
(b6)
WDC7
After Reset
000X XXXX2
Bit Name
Function
High-Order Bit of the Watchdog Timer
Cold Start-up/
Warm Start-up
Determine Flag(1,2, 3)
RW
RO
0: Cold start-up
1: Warm start-up
RW
Reserved Bit
Set to "0"
RW
Prescaler Select Bit
0: Divide-by-16
1: Divide-by-128
RW
NOTES:
1. The WDC5 bit remains set to "1", regardless of setting to "1" or "0".
2. The WDC5 bit is set to "0" when power is turned on and can be set to "1" by program only.
3. The WDC5 bit maintains a value set before reset, even after reset has been performed.
Watchdog Timer Start Register(1)
b7
b0
Symbol
WDTS
Address
000E16
After Reset
Indeterminate
Function
The watchdog timer is reset to start counting by a write instruction to the
WDTS register. Default value of the watchdog timer is always set to
"7FFF16" regardless of the value written.
NOTE:
1. Write the WDTS register after the watchdog timer interrupt is generated.
Figure 11.2 WDC Register and WDTS Register
Rev. 1.10 Oct. 18, 2005 Page 104 of 435
REJ09B0162-0110
RW
WO
11. Watchdog Timer
M32C/88 Group (M32C/88T)
System Clock Control Register 0(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
CM0
Bit
Symbol
Address
000616
After Reset
0000 10002
Bit Name
Function
b1 b0
CM00
Clock Output Function
Select Bit(2)
CM01
0 0: I/O port P53
0 1: Outputs fC
1 0: Outputs f8
1 1: Outputs f32
RW
RW
RW
CM02
0: Peripheral clock does not stop in
In Wait Mode, Peripheral
wait mode
Function Clock Stop Bit(9) 1: Peripheral clock stops in wait
mode(3)
RW
CM03
XCIN-XCOUT Drive
Capacity Select Bit(11)
0: Low
1: High
RW
CM04
Port XC Switch Bit
0: I/O port function
1: XCIN-XCOUT oscillation function(4)
RW
CM05
Main Clock (XIN-XOUT)
Stop Bit(5, 9)
0: Main clock oscillates
1: Main clock stops(6)
RW
CM06
Watchdog Timer
Function Select Bit
0: Watchdog timer interrupt
1: Reset(7)
RW
CM07
CPU Clock Select
Bit 0(8, 9, 10)
0: Clock selected by the CM21 bit
divided by MCD register setting
1: Sub clock
RW
NOTES:
1. Rewrite the CM0 register after the PRC0 bit in the PRCR register is set to "1" (write enabled).
2. When the PM07 bit in the PM0 register is set to "0" (BCLK output), set the CM01 and CM00 bits to
"002". When the PM15 and PM14 bits in the PM1 register are set to "012" (ALE output to P53), set the
CM01 and CM00 bits to "002". When the PM07 bit is set to "1" (function selected in the CM01 and
CM00 bits) in microprocessor or memory expansion mode, and the CM01 and CM00 bits are set to
"002", an "L" signal is output from port P53 (port P53 does not function as an I/O port).
3. fc32 does not stop running. When the CM02 bit is set to "1", the PLL clock cannot be used in wait
mode.
4. When setting the CM04 bit is set to "1", set the PD8_7 and PD8_6 bits in the PD8 register to "002"
(port P87 and P86 in input mode) and the PU25 bit in the PUR2 register to "0" (no pull-up).
5. When entering low-power consumption mode or on-chip oscillator low-power consumption mode, the
CM05 bit stops running the main clock. The CM05 bit cannot detect whether the main clock stops or
not. To stop running the main clock, set the CM05 bit to "1" after the CM07 bit is set to "1" with a stable
sub clock oscillation or after the CM21 bit in the CM2 register is set to "1" (on-chip oscillator clock).
When the CM05 bit is set to "1", the clock applied to XOUT becomes "H". The built-in feedback resistor
remains ON. XIN is pulled up to XOUT ("H" level) via the feedback resistor.
6. When the CM05 bit is set to "1", the MCD4 to MCD0 bits in the MCD register are set to "010002"
(divide-by-8 mode). In on-chip oscillation mode, the MCD4 to MCD0 bits are not set to "010002" even
if the CM05 bit terminates XIN-XOUT.
7. Once the CM06 bit is set to "1", it cannot be set to "0" by program.
8. After the CM04 bit is set to "1" with a stable sub clock oscillation, set the CM07 bit to "1" from "0".
After the CM05 bit is set to "0" with a stable main clock oscillation, set the CM07 bit to "0" from "1".
Do not set the CM07 bit and CM04 or CM05 bit simultaneously.
9. When the PM21 bit in the PM2 register is set to "1" (clock change disable), the CM02, CM05 and
CM07 bits do not change even when written.
10. After the CM07 bit is set to "0", set the PM21 bit to "1".
11. When stop mode is entered, the CM03 bit is set to "1".
Figure 11.3 CM0 Register
Rev. 1.10 Oct. 18, 2005 Page 105 of 435
REJ09B0162-0110
11. Watchdog Timer
M32C/88 Group (M32C/88T)
11.1 Count Source Protection Mode
In count source protection mode, the on-chip oscillator clock is used as a count source for the watchdog
timer. The count source protection mode allows the on-chip oscillator clock to run continuously, maintaining watchdog timer operation even if the program error occurs and the CPU clock stops running.
Follow the procedures below when using this mode.
(1) Set the PRC0 bit in the PRCR register to "1" (write to CM0 register enabled)
(2) Set the PRC1 bit in the PRCR register to "1" (write to PM2 register enabled)
(3) Set the CM06 bit in the CM0 register to "1" (reset when the watchdog timer overflows)
(4) Set the PM22 bit in the PM2 register to "1" (the on-chip oscillator clock as a count source of the watchdog timer)
(5) Set the PRC0 bit to "0" (write to CM0 register disabled)
(6) Set the PRC1 bit to "0" (write to PM2 register disabled)
(7) Write to the WDTS register (the watchdog timer starts counting)
The followings will occur when the PM22 bit is set to "1".
• The on-chip oscillator starts oscillating and the on-chip oscillator clock becomes a count source for
the watchdog timer.
Watchdog timer cycle =
Counter value of watchdog timer (32768)
On-chip oscillator clock
• Write to the CM10 bit in the CM1 register is disabled. (The bit setting remains unchanged even if set
it to "1". The microcomputer does not enter stop mode.)
• In wait mode or hold state, the watchdog timer continues running. However, the watchdog timer
interrupt cannot be used to exit wait mode.
Rev. 1.10 Oct. 18, 2005 Page 106 of 435
REJ09B0162-0110
12. DMAC
M32C/88 Group (M32C/88T)
12. DMAC
This microcomputer contains four DMAC (direct memory access controller) channels that allow data to be
sent to memory without using the CPU. DMAC transmits a 8- or 16-bit data from a source address to a
destination address whenever a transmit request occurs. DMA0 and DMA1 must be prioritized if using
DMAC. DMA2 and DMA3 share registers required for high-speed interrupts. High-speed interrupts cannot
be used when using three or more DMAC channels.
The CPU and DMAC use the same data bus, but DMAC has a higher bus access privilege than the CPU.
The cycle-steal method employed on DMAC enables high-speed operation between a transfer request and
the complete transmission of 16-bit (word) or 8-bit (byte) data. Figure 12.1 shows a mapping of registers to
be used for DMAC. Table 12.1 lists specifications of DMAC. Figures 12.2 to 12.5 show registers associated with DMAC.
Because the registers shown in Figure 12.1 are allocated in the CPU, use the LDC instruction to write to the
registers. To set the DCT2, DCT3, DRC2, DRC3, DMA2 and DMA3 registers, set the B flag to "1" (register
bank 1) and set the R0 to R3, A0, A1 registers with the MOV instruction.
To set the DSA2 and DSA3 registers, set the B flag to "1" and set the SB and FB registers with the LDC
instruction. To set the DRA2 and DRA3 registers, set the SVP and VCT registers with the LDC instruction.
DMAC-associated Registers
DMD0
DMA Mode Register 0
DMD1
DMA Mode Register 1
DCT0
DMA 0 Transfer Count Register
DCT1
DMA 1 Transfer Count Register
DRC0
DMA 0 Transfer Count Reload Register(1)
DRC1
DMA 1 Transfer Count Reload Register(1)
DMA0
DMA 0 Memory Address Register
DMA1
DMA 1 Memory Address Register
DSA0
DMA 0 SFR Address Register
DSA1
DMA 1 SFR Address Register
DRA0
DMA 0 Memory Address Reload Register(1)
DRA1
DMA 1 Memory Address Reload Register(1)
When Three or More DMAC Channels are Used,
the Register Bank 1 is Used as DMAC Registers
When Three or More DMAC Channels are Used,
the High-speed Interrupt Register is Used as DMAC
Registers
Flag Save Register
DCT2 (R0)
DMA2 Transfer Count Register
SVF
DCT3 (R1)
DMA3 Transfer Count Register
DRA2 (SVP)
DMA2 Memory Address Reload Register(1)
DRC2 (R2)
DMA2 Transfer Count Reload Register(1)
DRA1 (VCT)
DMA3 Memory Address Reload Register(1)
DRC3 (R3)
DMA3 Transfer Count Reload Register(1)
DMA2 (A0)
DMA2 Memory Address Register
DMA3 (A1)
DMA3 Memory Address Register
DSA2 (SB)
DMA2 SFR Address Register
DSA3 (FB)
DMA3 SFR Address Register
NOTE:
1. Registers are used for repeat transfer, not for single transfer.
Figure 12.1 Register Mapping for DMAC
Rev. 1.10 Oct. 18, 2005 Page 107 of 435
REJ09B0162-0110
When using DMA2 and DMA3, use the CPU registers shown in parentheses ().
M32C/88 Group (M32C/88T)
12. DMAC
DMAC starts a data transfer by setting the DSR bit in the DMiSL register (i=0 to 3) or by using an interrupt
request, generated by the functions determined by the DSEL 4 to DSEL0 bits in the DMiSL register, as a
DMA request. Unlike interrupt requests, the I flag and interrupt control register do not affect DMA. Therefore, a DMA request can be acknowledged even if an interrupt is disabled and cannot be acknowledged. In
addition, the IR bit in the interrupt control register does not change when a DMA request is acknowledged.
Table 12.1 DMAC Specifications
Item
Specification
Channels
4 channels (cycle-steal method)
Transfer Memory Space
• From a desired address in a 16-Mbyte space to a fixed address in a
16-Mbyte space
• From a fixed address in a 16-Mbyte space to a desired address in a
16-Mbyte space
Maximum Bytes Transferred
128 Kbytes (when a 16-bit data is transferred) or 64 Kbytes (with an 8bit data is transferred)
________
________
DMA Request Source(1)
Falling edge or both edges of signals applied to the INT0 to INT3 pins
Timers A0 to A4 interrupt requests
Timers B0 to B5 interrupt requests
UART0 to UART4 transmit and receive interrupt requests
A/D0 conversion interrupt request
Intelligent I/O interrupt request
CAN interrupt request
Software trigger
Channel Priority
DMA0 > DMA1 > DMA2 > DMA3 (DMA0 has highest priority)
Transfer Unit
8 bits, 16 bits
Destination Address
Forward/fixed (forward and fixed directions cannot be specified when
specifying source and destination addresses simultaneously)
Transfer Mode Single Transfer Transfer is completed when the DCTi register (i = 0 to 3) is set to "000016"
Repeat Transfer When the DCTi register is set to "000016", the value of the DRCi register
is reloaded into the DCTi register and the DMA transfer is continued
DMA Interrupt Request Generation Timing When the DCTi register changes "000116" to "000016"
DMA Startup
Single Transfer DMA starts when a DMA request is generated after the DCTi register is
set to "000116" or more and the MDi1 and MD0 bits in the DMDj register
(j = 0,1) are set to "012" (single transfer)
Repeat Transfer DMA starts when a DMA request is generated after the DCTi register is
set to "000116" or more and the MDi1 and MDi0 bits are set to "112"
(repeat transfer)
DMA Stop
Single Transfer DMA stops when the MDi1 and MDi0 bits are set to "002" (DMA disabled) and the DCTi register is set to "000016" (0 DMA transfer) by DMA
transfer or write
Repeat Transfer DMA stops when the MDi1 and MDi0 bits are set to "002" and the DCTi
register is set to "000016" and the DRCi register set to "000016"
Reload Timing to the DCTi
When the DCTi register is set to "000016" from "000116" in repeat transor DMAi Register
fer mode
DMA Transfer Cycles
Minimum 3 cycles between SFRs and internal RAM
NOTE:
1. The IR bit in the interrupt control register does not change when a DMA request is acknowledged.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 108 of 435
12. DMAC
M32C/88 Group (M32C/88T)
DMAi Request Source Select Register (i=0 to 3)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
DM0SL to DM3SL 037816, 037916, 037A16, 037B16
Bit
Symbol
Bit Name
After Reset
0X00 00002
Function
RW
DSEL0
RW
DSEL1
RW
DSEL2
DMA Request Source
Select Bit(1)
See Table 12.2 for the DMiSL
register (i=0 to 3) function
RW
DSEL3
RW
DSEL4
RW
DSR
Software DMA
Request Bit(2)
When a software trigger is selected,
a DMA request is generated by
RW
setting this bit to "1" (When read, its
content is always "0")
Reserved Bit
When read,
its content is indeterminate
RO
DMA Request Bit(2, 3)
0: Not requested
1: Requested
RW
(b6)
DRQ
NOTES:
1. Change the DSEL4 to DSEL0 bit settings while the MDi1 and MDi0 bits in the DMD0 and DMD1
registers are set to "002" (DMA disabled). Also, set the DRQ bit to "1" simultaneously when the
DSEL4 to DSEL0 bit settings are changed.
e.g., MOV.B #083h, DMiSL ; Set timer A0
2. When the DSR bit is set to "1", set the DRQ bit to "1" simultaneously.
e.g., OR.B #0A0h, DMiSL
3. Do not set the DRQ bit to "0".
Figure 12.2 DM0SL to DM3SL Registers
Rev. 1.10 Oct. 18, 2005 Page 109 of 435
REJ09B0162-0110
12. DMAC
M32C/88 Group (M32C/88T)
Table 12.2 DMiSL Register (i = 0 to 3) Function
Setting Value
DMA Request Source
DMA0
DMA1
Falling Edge of INT0
Falling Edge of INT1
b4 b3 b2 b1 b0
0 0 0 1 0
DMA3
Software trigger
0 0 0 0 0
0 0 0 0 1
DMA2
Both Edges of INT0
Both Edges of INT1
Falling Edge of INT2
Both Edges of INT2
0 0 0 1 1
Timer A0 Interrupt Request
0 0 1 0 0
Timer A1 Interrupt Request
0 0 1 0 1
Timer A2 Interrupt Request
0 0 1 1 0
Timer A3 Interrupt Request
0 0 1 1 1
Timer A4 Interrupt Request
0 1 0 0 0
Timer B0 Interrupt Request
0 1 0 0 1
Timer B1 Interrupt Request
0 1 0 1 0
Timer B2 Interrupt Request
0 1 0 1 1
Timer B3 Interrupt Request
0 1 1 0 0
Timer B4 Interrupt Request
0 1 1 0 1
Timer B5 Interrupt Request
0 1 1 1 0
UART0 Transmit Interrupt Request
0 1 1 1 1
UART0 Receive or ACK Interrupt Request(3)
1 0 0 0 0
UART1 Transmit Interrupt Request
1 0 0 0 1
UART1 Receive or ACK Interrupt Request(3)
1 0 0 1 0
UART2 Transmit Interrupt Request
1 0 0 1 1
UART2 Receive or ACK Interrupt Request(3)
1 0 1 0 0
UART3 Transmit Interrupt Request
1 0 1 0 1
UART3 Receive or ACK Interrupt Request(3)
1 0 1 1 0
UART4 Transmit Interrupt Request
1 0 1 1 1
UART4 Receive or ACK Interrupt Request(3)
Falling Edge of INT3(1)
Both Edges of
(Note 2)
INT3(1) (Note 2)
A/D0 Interrupt Request
1 1 0 0 0
1 1 0 0 1
Intelligent I/O
Interrupt 0 Request(6)
1 1 0 1 0
Intelligent I/O
Interrupt 1 Request(7)
1 1 0 1 1
1 1 1 0 0
Intelligent I/O
Interrupt 2 Request
Intelligent I/O
Interrupt 9 Request(4)
Intelligent I/O
Interrupt 8 Request
Intelligent I/O
Interrupt 3 Request
Intelligent I/O
Interrupt 10 Request(5)
Intelligent I/O
Interrupt 2 Request(8)
Intelligent I/O
Interrupt 9 Request(4)
Intelligent I/O
Interrupt 4 Request
CAN Interrupt 2
Request
Intelligent I/O
Interrupt 3 Request(9)
Intelligent I/O
Interrupt 10 Request(5)
CAN Interrupt 5
Request
Intelligent I/O
Interrupt 0 Request(6)
1 1 1 0 1
Intelligent I/O
Interrupt 4 Request
CAN Interrupt 2
Request
CAN Interrupt 8
Request
Intelligent I/O
Interrupt 1 Request(7)
1 1 1 1 0
CAN Interrupt 5
Intelligent I/O
Interrupt 0 Request(6)
Request
1 1 1 1 1
CAN Interrupt 8
Request
Intelligent I/O
Interrupt 1 Request(7)
Intelligent I/O
Interrupt 2 Request(8)
Intelligent I/O
Interrupt 8 Request
Intelligent I/O
Interrupt 3 Request(9)
NOTES:
1. If the INT3 pin is used for data bus in memory expansion mode or microprocessor mode, a DMA3 interrupt request
cannot be generated by a signal applied to the INT3 pin.
2. The falling edge and both edges of signals applied to the INTj pin (j=0 to 3) cause a DMA request generation. The
INT interrupt (the POL bit in the INTjlC register, the LVS bit, the IFSR register) is not affected and vice versa.
3. Use the UkSMR register and UkSMR2 register (k=0 to 4) to switch between the UARTk receive and ACK interrupt
as a DMA request source.
To use the ACK interrupt for a DMA reqest, set the IICM bit in the UkSMR register to "1" and the IICM2 bit in the
UkSMR2 register to "0".
4. The same setting is used to generate an intelligent I/O interrupt 9 request and a CAN interrupt 0 request.
5. The same setting is used to generate an intelligent I/O interrupt 10 request and a CAN interrupt 1 request.
6. The same setting is used to generate an intelligent I/O interrupt 0 request and a CAN interrupt 3 request.
7. The same setting is used to generate an intelligent I/O interrupt 1 request and a CAN interrupt 4 request.
8. The same setting is used to generate an intelligent I/O interrupt 2 request and a CAN interrupt 6 request.
9. The same setting is used to generate an intelligent I/O interrupt 3 request and a CAN interrupt 7 request.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 110 of 435
12. DMAC
M32C/88 Group (M32C/88T)
DMA Mode Register 0(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
DMD0
Bit
Symbol
Address
(CPU Internal Register)
Bit Name
After Reset
0016
Function
RW
b1 b0
MD00
Channel 0 Transfer
Mode Select Bit
MD01
0 0: DMA disabled
0 1: Single transfer
1 0: Do not set to this value
1 1: Repeat transfer
RW
RW
BW0
Channel 0 Transfer
Unit Select Bit
0: 8 bits
1: 16 bits
RW0
Channel 0 Transfer
Direction Select Bit
0: Fixed address to memory (forward direction)
RW
1: Memory (forward direction) to fixed address
RW
b5 b4
MD10
Channel 1 Transfer
Mode Select Bit
MD11
0 0: DMA disabled
0 1: Single transfer
1 0: Do not set to this value
1 1: Repeat transfer
RW
RW
BW1
Channel 1 Transfer
Unit Select Bit
0: 8 bits
1: 16 bits
RW1
Channel 1 Transfer
Direction Select Bit
0: Fixed address to memory (forward direction)
RW
1: Memory (forward direction) to fixed address
RW
NOTE:
1. Use the LDC instruction to set the DMD0 register.
DMA Mode Register 1(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
DMD1
Bit
Symbol
Address
(CPU internal register)
Bit Name
After Reset
0016
Function
RW
b1 b0
MD20
MD21
0 0: DMA disabled
Channel 2 Transfer 0 1: Single transfer
Mode Select Bit
1 0: Do not set to this value
1 1: Repeat transfer
RW
RW
BW2
Channel 2 Transfer 0: 8 bits
1: 16 bits
Unit Select Bit
RW2
Channel 2 Transfer 0: Fixed address to memory (forward direction)
RW
Direction Select Bit 1: Memory (forward direction) to fixed address
MD30
MD31
b5 b4
0 0: DMA disabled
Channel 3 Transfer 0 1: Single transfer
Mode Select Bit
1 0: Do not set to this value
1 1: Repeat transfer
RW
RW
RW
BW3
Channel 3 Transfer 0: 8 bits
1: 16 bits
Unit Select Bit
RW3
Channel 3 Transfer 0: Fixed address to memory (forward direction)
RW
Direction Select Bit 1: Memory (forward direction) to fixed address
NOTE:
1. Use the LDC instruction to set the DMD1 register.
Figure 12.3 DMD0 and DMD1 Registers
Rev. 1.10 Oct. 18, 2005 Page 111 of 435
REJ09B0162-0110
RW
12. DMAC
M32C/88 Group (M32C/88T)
DMAi Transfer Count Register (i=0 to 3)
b15
b8 b7
b0
Symbol
DCT0(2)
DCT1(2)
DCT2(bank1;R0)(3)
DCT3(bank1;R1)(4)
Address
(CPU Internal Register)
(CPU Internal Register)
(CPU Internal Register)
(CPU Internal Register)
Function
Set the number of transfers
After Reset
XXXX16
XXXX16
000016
000016
Setting Range
RW
000016 to FFFF16(1)
RW
NOTES:
1. When the DCTi register is set to "000016", no data transfer occurs regardless of a DMA request.
2. Use the LDC instruction to set the DCT0 and DCT1 registers.
3. To set the DCT2 register, set the B flag in the FLG register to "1" (register bank 1) and set the R0
register. Use the MOV instruction to set the R0 register.
4. To set the DCT3 register, set the B flag to "1" and set R1 register. Use the MOV instruction to
set the R1 register.
DMAi Transfer Count Reload Register (i=0 to 3)
b15
b8 b7
b0
Symbol
DRC0(1)
DRC1(1)
DRC2(bank1;R2)(2)
DRC3(bank1;R3)(3)
Address
(CPU Internal Register)
(CPU Internal Register)
(CPU Internal Register)
(CPU Internal Register)
Function
Set the number of transfers
After Reset
XXXX16
XXXX16
000016
000016
Setting Range
RW
000016 to FFFF16
RW
NOTES:
1. Use the LDC instruction to set the DRC0 and DRC1 registers.
2. To set the DRC2 register, set the B flag in the FLG register to "1" (register bank 1) and set the R2
register. Use the MOV instruction to set the R2 register.
3. To set the DRC3 register, set the B flag to "1" and set R3 register. Use the MOV instruction to set the
R3 register.
Figure 12.4 DCT0 to DCT3 Registers and DRC0 to DRC3 Registers
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 112 of 435
12. DMAC
M32C/88 Group (M32C/88T)
DMAi Memory Address Register (i=0 to 3)
b23
b16 b15
b8 b7
b0
Symbol
DMA0(2)
DMA1(2)
DMA2(bank1;A0)(3)
DMA3(bank1;A1)(4)
Address
(CPU Internal Register)
(CPU Internal Register)
(CPU Internal Register)
(CPU Internal Register)
Function
Set source memory address or destination
memory address(1)
After Reset
XXXXXX16
XXXXXX16
00000016
00000016
Setting Range
RW
00000016 to FFFFFF16
(16-Mbyte space)
RW
NOTES:
1. When the RWk bit (k=0 to 3) in the DMDj register (j=0, 1)is set to "0" (fixed address to memory), a
destination address is selected. When the RWk bit is set to "1" (memory to fixed address), a source
address is selected.
2. Use the LDC instruction to set the DMA0 and DMA1 registers.
3. To set the DMA2 register, set the B flag in the FLG register to "1" (register bank 1) and set the A0
register. Use the MOV instruction to set the A0 register.
4. To set the DMA3 register, set the B flag to "1" and set the A1 register. Use the MOV instruction to set
the A1 register.
DMAi SFR Address Register (i=0 to 3)
b23
b16 b15
b8 b7
b0
Symbol
DSA0(2)
DSA1(2)
DSA2(bank1;SB)(3)
DSA3(bank1;FB)(4)
Address
(CPU Internal Register)
(CPU Internal Register)
(CPU Internal Register)
(CPU Internal Register)
Function
Set source fixed address or destination fixed
address(1)
After Reset
XXXXXX16
XXXXXX16
00000016
00000016
Setting Range
RW
00000016 to FFFFFF16
(16-Mbyte space)
RW
NOTES:
1. When the RWk bit (k=0 to 3) in the DMDj register (j=0, 1)is set to "0" (fixed address to memory), a
source address is selected. When the RWk bit is set to "1" (memory to fixed address), a destination
address is selected.
2. Use the LDC instruction to set the DSA0 and DSA1 registers.
3. To set the DSA2 register, set the B flag in the FLG register to "1" (register bank 1) and the set the SB
register. Use the LDC instruction to set the SB register.
4. To set the DSA3 register, set the B flag to "1" and set the FB register. Use the LDC instruction to set
the PB register.
DMAi Memory Address Reload Register(1) (i=0 to 3)
b23
b16 b15
b8 b7
b0
Symbol
DRA0
DRA1
DRA2(SVP)(2)
DRA3(VCT)(3)
Address
(CPU Internal Register)
(CPU Internal Register)
(CPU Internal Register)
(CPU Internal Register)
Function
Set source memory address or destination
memory address(1)
After Reset
XXXXXX16
XXXXXX16
XXXXXX16
XXXXXX16
Setting Range
RW
00000016 to FFFFFF16
(16-Mbyte space)
RW
NOTES:
1. Use the LDC instruction to set the DRA0 and DRA1 registers.
2. To set the DRA2 register, set the SVP register.
3. To set the DRA3 register, set the VCT register.
Figure 12.5 DMA0 to DMA3 Registers, DSA0 to DSA3 Registers and DRA0 to DRA3 Registers
Rev. 1.10 Oct. 18, 2005 Page 113 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
12. DMAC
12.1 Transfer Cycle
Transfer cycle contains a bus cycle to read data from a memory or the SFR area (source read) and a bus
cycle to write data to a memory space or the SFR area (destination write). The number of read and write
bus cycles depends on source and destination addresses.
12.1.1 Effect of Source and Destination Addresses
When a 16-bit data is transferred with a 16-bit data bus and a source address starting with an odd
address, source read cycle is incremented by one bus cycle, compared to a source address starting with
an even address.
When a 16-bit data is transferred with a 16-bit data bus and a destination address starting with an odd
address, a destination write cycle is incremented by one bus cycle, compared to a destination address
starting with an even address.
12.1.2 Effect of Software Wait State
When the SFR area or memory space with software wait states is accessed, the number of CPU clock
cycles is incremented by software wait states.
Figure 12.6 shows an example of a transfer cycle for the source-read bus cycle. In Figure 12.6, the
number of source-read bus cycles is illustrated under different conditions, provided that the destination
address is an address of an external space with the destination-write cycle as two CPU clock cycles
(=one bus cycle). In effect, the destination-write bus cycle is also affected by each condition and the
transfer cycles change accordingly. To calculate a transfer cycle, apply respective conditions to both
destination-write bus cycle and source-read bus cycle.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 114 of 435
12. DMAC
M32C/88 Group (M32C/88T)
(1) When 8-bit data is transferred
or when 16-bit data is transferred with a 16-bit data bus from an even source address
CPU Clock
Address
Bus
CPU Use
Source
Destination
CPU Use
RD Signal
WR Signal
Data bus
CPU Use
Destination
Source
CPU Use
(2) When 16-bit data is transferred from an odd source address
CPU
CPUClock
Clock
Address
Bus
CPU Use
Source
Source + 1
CPU Use
Destination
RD Signal
WR Signal
Data Bus
CPU Use
Source
Source + 1
CPU Use
Destination
(3) When one wait state is inserted into the source-read bus cycle under the conditions in (1)
CPU Clock
Address
Bus
CPU Use
Source
Destination
CPU Use
RD Signal
WR Signal
Data Bus
CPU Use
Source
CPU Use
Destination
(4) When one wait state is inserted into the source-read bus cycle under the conditions in (2)
CPU Clock
Address
Bus
CPU Use
Source
Source + 1
Destination
CPU Use
RD Signal
WR Signal
Data Bus
CPU Use
Source
Source + 1
Destination
CPU Use
NOTE:
1. The above applies when the destination-write bus cycle is 2 CPU clock cycles (=1 bus cycle).
However, if the destination-write bus cycle is pleaced under these conditions, it will change to
the same timing as the source-read cycle illustrated above.
Figure 12.6 Transfer Cycle Examples with the Source-Read Bus Cycle
Rev. 1.10 Oct. 18, 2005 Page 115 of 435
REJ09B0162-0110
12. DMAC
M32C/88 Group (M32C/88T)
12.2 DMAC Transfer Cycle
The number of DMAC transfer cycle can be calculated as follows.
Any combination of even or odd transfer read and write addresses are possible. Table 12.3 lists the number
of DMAC transfer cycles. Table 12.4 lists coefficient j, k.
Transfer cycles per transfer = Number of read cycle x j + Number of write cycle x k
Table 12.3 DMAC Transfer Cycles
Transfer Unit
Bus Width
8-bit Transfer
(BWi=0)
16 Bits
8 Bits
16-bit Transfer
(BWi=1)
16 Bits
8 Bits
Single-chip Mode
Access
Address
Read Cycle
Write Cycle
Even
1
1
Odd
1
1
Even
-
-
Odd
-
-
Even
1
1
Odd
2
2
Even
-
-
Odd
-
-
BWi: Bit in the DMDp register (i=0 to 3, p=0, 1)
Table 12.4 Coefficient j, k
Internal space
Internal ROM or internal
RAM with no wait state
Internal ROM or internal
RAM with a wait state
SFR
area
j=1
k=1
j=2
k=2
j=2
k=2
12.3 Channel Priority and DMA Transfer Timing
When multiple DMA requests are generated in the same sampling period, between the falling edge of the
CPU clock and the next falling edge, the DRQ bit in the DMiSL register (i = 0 to 3) is set to "1" (requested)
simultaneously. Channel priority in this case is : DMA0 > DMA1 > DMA2 > DMA3.
Figure 12.7 shows an example of the DMA transfer by external source.
In Figure 12.7, the DMA0 request having highest priority is received first to start a transfer when a DMA0
request and DMA1 request are generated simultaneously. After one DMA0 transfer is completed, the bus
privilege is returned to the CPU. When the CPU has completed one bus access, the DMA1 transfer starts.
After one DMA1 transfer is completed, the privilege is again returned to the CPU.
In addition, DMA requests cannot be counted up since each channel has one DRQ bit. Therefore, when
DMA requests, as DMA1 in Figure 12.7, occur more than once before receiving bus privilege, the DRQ bit
is set to "0" as soon as privilege is acquired. The bus privilege is returned to the CPU when one transfer is
completed.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 116 of 435
12. DMAC
M32C/88 Group (M32C/88T)
When DMA transfer request signals by external source are applied to INT0 and
INT1 simultaneously and a DMA transfer with minimum cycle occurs
CPU Clock
DMA0
DMA1
CPU
INT0
AAA
AAA
AAA
AAA
AAAAAAAA AAA
AA
A
AAA
AA
AA
A
AAA
AA
DRQ Bit in the
DMA0 Register
INT1
DRQ Bit in the
DMA1 Register
Figure 12.7 DMA Transfer by External Source
Rev. 1.10 Oct. 18, 2005 Page 117 of 435
REJ09B0162-0110
Bus
privilege
acquired
M32C/88 Group (M32C/88T)
13. DMACII
13. DMAC II
DMAC II performs memory-to-memory transfer, immediate data transfer and calculation transfer, which
transfers the sum of two data added by an interrupt request from any peripheral functions.
Table 13.1 lists specifications of DMAC II.
Table 13.1 DMAC II Specifications
Item
DMAC II Request Source
Specification
Interrupt requests generated by all peripheral functions when the ILVL2 to
ILVL0 bits are set to "1112"
Transfer Data
• Data in memory is transferred to memory (memory-to-memory transfer)
• Immediate data is transferred to memory (immediate data transfer)
• Data in memory (or immediate data) + data in memory are transferred to
memory (calculation transfer)
Transfer Block
8 bits or 16 bits
Transfer Space
64-Kbyte space in addresses 0000016 to 0FFFF16(1, 2)
Transfer Direction
Fixed or forward address
Selected separately for each source address and destination address
Transfer Mode
Single transfer, burst transfer
Chained Transfer Function Parameters (transfer count, transfer address and other information) are
switched when transfer counter reaches zero
End-of-Transfer Interrupt
Interrupt occurs when a transfer counter reaches zero
Multiple Transfer Function Multiple data can be transferred by a generated request for one DMAC II transfer
NOTES:
1. When transferring a 16-bit data to destination address 0FFFF16, it is transferred to 0FFFF16 and
1000016. The same transfer occurs when the source address is 0FFFF16.
2. The actual space where transfer can occurs is limited due to internal RAM capacity.
13.1 DMAC II Settings
DMAC II can be made available by setting up the following registers and tables.
• RLVL register
• DMAC II Index
• Interrupt control register of the peripheral function causing a DMAC II request
• The relocatable vector table of the peripheral function causing a DMAC II request
• IRLT bit in the IIOiIE register (i = 0 to 5, 8 to 11) if using the intelligent I/O or CAN interrupt
Refer to 10. Interrupts for details on the IIOiIE register.
13.1.1 RLVL Register
When the DMAII bit is set to "1" (DMAC II transfer) and the FSIT bit to "0" (normal interrupt), DMAC II is
activated by an interrupt request from any peripheral function with the ILVL2 to ILVL0 bits in the interrupt
control register set to "1112" (level 7).
Figure 13.1 shows the RLVL register.
Rev. 1.10 Oct. 18, 2005 Page 118 of 435
REJ09B0162-0110
13. DMACII
M32C/88 Group (M32C/88T)
Exit Priority Register
b7
b6
b5
b4
b3
b2
b1
Symbol
RLVL
b0
Bit
Symbol
RLVL0
RLVL1
RLVL2
Address
009F16
After Reset
XXXX 00002
Bit Name
Function
b2b1b0
0 0 0 : Level 0
0 0 1 : Level 1
Stop/Wait Mode Exit
0 1 0 : Level 2
Minimum Interrupt Priority 0 1 1 : Level 3
1 0 0 : Level 4
Level Control Bit(1)
1 0 1 : Level 5
1 1 0 : Level 6
1 1 1 : Level 7
0: Interrupt priority level 7 is used
for normal interrupt
1: Interrupt priority level 7 is used
for high-speed interrupt
FSIT
High-Speed Interrupt
Set Bit(2)
(b4)
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
DMAII
DMA II Select
Bit(4)
0: Interrupt priority level 7 is used
for interrupt
1: Interrupt priority level 7 is used
for DMA II transfer(3)
RW
RW
RW
RW
RW
RW
Nothing is assigned. When write, set to "0".
(b7 - b6) When read, its content is indeterminate.
NOTES:
1. The microcomputer exits stop or wait mode when the requested interrupt priority level is higher than
the level set in the RLVL2 to RLVL0 bits. Set the RLVL2 to RLVL0 bits to the same value as IPL in
the FLG register.
2. When the FSIT bit is set to "1", an interrupt having the interrupt priority level 7 becomes the high-speed
interrupt. In this case, set only one interrupt to the interrupt priority level 7 and the DMAII bit to "0".
3. Set the ILVL2 to ILVL0 bits in the interrupt control register after setting the DMAII bit to "1".
Do not change the DMAII bit setting to "0" after setting the DMAII bit to "1". Set the FSIT bit to "0"
when the DMAII bit to "1".
4. The DMAII bit becomes indeterminate after reset. To use the DMAII bit for an interrupt setting, set it
to "0" before setting the interrupt control register.
Figure 13.1 RLVL Register
Rev. 1.10 Oct. 18, 2005 Page 119 of 435
REJ09B0162-0110
13. DMACII
M32C/88 Group (M32C/88T)
13.1.2 DMAC II Index
The DMAC II index is a data table which comprises 8 to 18 bytes (maximum 32 bytes when the multiple
transfer function is selected). The DMAC II index stores parameters for transfer mode, transfer counter,
source address (or immediate data), operation address as an address to be calculated, destination address, chained transfer address, and end-of-transfer interrupt address.
This DMAC II index must be located on the RAM area.
Figure 13.2 shows a configuration of the DMAC II index. Table 13.2 lists a configuration of the DMAC II
index in transfer mode.
Memory-to-Memory Transfer, Immediate Transfer,
Calculation Transfer
DMAC II Index
Starting Address
(BASE)
BASE + 2
Multiple Transfer
16 bits
16 bits
Transfer Mode
(MOD)
BASE
Transfer Mode
(MOD)
Transfer Counter
(COUNT)
BASE + 2
Transfer Counter
(COUNT)
(SADR1)
BASE + 4
Transfer Source Address (or immediate data) (SADR)
BASE + 4
Transfer Source Address
BASE + 6
Operation Address(1)
(OADR)
BASE + 6
Transfer Destination Address
(DADR1)
BASE + 8
Transfer Destination Address
(DADR)
BASE + 8
Transfer Source Address
(SADR2)
BASE + 10
Chained Transfer Address(2)
(CADR0)
BASE + 10 Transfer Destination Address
(DADR2)
BASE + 12
Chained Transfer Address(2)
(CADR1)
BASE + 14
End-of-Transfer Interrupt Address(3)
(IADR0)
BASE + 28 Transfer Source Address
(SADR7)
BASE + 16
End-of-Transfer Interrupt Address(3)
(IADR1)
BASE + 30 Transfer Destination Address
(DADR7)
NOTES:
1. This data is not required when not using the calculation transfer function.
2. This data is not required when not using the chained transfer function.
3. This data is not required when not using the end-of-transfer interrupt.
The DMAC II index must be located on the RAM. Necessary data is set front-aligned. For example, if not using a calculation
transfer function, set destination address to BASE+6. (See Table 13.2)
Starting address of the DMAC II index must be set in the interrupt vector for the peripheral function interrupt causing a DMAC II request.
Figure 13.2 DMAC II Index
The followings are details of the DMAC II index. Set these parameters in the specified order listed in
Table 13.2, according to DMAC II transfer mode.
• Transfer mode (MOD)
Two-byte data is required to set transfer mode. Figure 13.3 shows a configuration for transfer mode.
• Transfer counter (COUNT)
Two-byte data is required to set the number of transfer.
• Transfer source address (SADR)
Two-byte data is required to set the source memory address or immediate data.
• Operation address (OADR)
Two-byte data is required to set a memory address to be calculated. Set this data only when using
the calculation transfer function.
• Transfer destination address (DADR)
Two-byte data is required to set the destination memory address.
• Chained transfer address (CADR)
Four-byte data is required to set the starting address of the DMAC II index for the next transfer. Set
this data only when using the chained transfer function.
• End-of-transfer interrupt address (IADR)
Four-byte data is required to set a jump address for end-of-transfer interrupt processing. Set this
data only when using the end-of-transfer interrupt.
Rev. 1.10 Oct. 18, 2005 Page 120 of 435
REJ09B0162-0110
13. DMACII
M32C/88 Group (M32C/88T)
Table 13.2 DMAC II Index Configuration in Transfer Mode
Memory-to-Memory Transfer
/Immediate Data Transfer
Transfer Data
Calculation Transfer
Multiple Transfer
Chained Transfer Not Used
Used
Not Used
Used
Not Used
Used
Not Used
Used
Not Available
End-of-Transfer Not Used
Interrupt
Not Used
Used
Used
Not Used
Not Used
Used
Used
Not Available
DMAC II
Index
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
MOD
COUNT
COUNT
COUNT
COUNT
COUNT
COUNT
COUNT
COUNT
COUNT
SADR
SADR
SADR
SADR
SADR
SADR
SADR
SADR
SADR1
DADR
DADR
DADR
DADR
OADR
OADR
OADR
OADR
DADR1
CADR0
IADR0
CADR0
DADR
DADR
DADR
DADR
CADR1
IADR1
CADR1
10 bytes
CADR0
IADR0
CADR0
CADR1
IADR1
CADR1
SADRi
IADR0
DADRi
IADR1
i=1 to 7
max. 32 bytes
(when i=7)
8 bytes
12 bytes
12 bytes
IADR0
IADR1
14 bytes
14 bytes
16 bytes
18 bytes
Transfer Mode (MOD)(1)
b15
b8 b7
b0
Bit
Symbol
Bit Name
Function
(MULT=0)
SIZE
Transfer Unit
Select Bit
0: 8 bits
1: 16 bits
IMM
Transfer Data
Select Bit
0: Immediate data
1: Memory
Function
(MULT=1)
RW
RW
Set to "1"
RW
UPDS
Transfer Source
0: Fixed address
Direction Select Bit 1: Forward address
RW
UPDD
Transfer Destination 0: Fixed address
Direction Select Bit 1: Forward address
RW
OPER/ Calculation Transfer 0: Not used
CNT0(2) Function Select Bit 1: Used
BRST/ Burst Transfer
CNT1(2) Select Bit
0: Single transfer
1: Burst transfer
INTE/ End-of-Transfer
CNT2(2) Interrupt Select Bit
0: Interrupt not used
1: Use interrupt
CHAIN
Chained Transfer
Select Bit
b6 b5 b4
0 0 0: Do not set
to this value
0 0 1: Once
0 1 0: Twice
:
:
1 1 0: 6 times
1 1 1: 7 times
0: Chained transfer not used
Set to "0"
1: Use chained transfer
RW
RW
RW
RW
Nothing is assigned. When write, set to "0".
(b14 - b8) When read, its content is indeterminate.
MULT
Multiple Transfer
Select Bit
0: Multiple
transfer not used
1: Use multiple
transfer
RW
NOTES:
1. MOD must be located on the RAM.
2. When the MULT bit is set to "0" (no multiple transfer), bits 6 to 4 becomes the INTE, OPER and BRST
bits. When the MULT bit is set to "1" (multiple transfer), bits 6 to 4 becomes the CNT2 to CNT0 bits.
Figure 13.3 MOD
Rev. 1.10 Oct. 18, 2005 Page 121 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
13. DMACII
13.1.3 Interrupt Control Register for the Peripheral Function
For the peripheral function interrupt activating DMAC II, set the ILVL2 to ILVL0 bits to "1112" (level 7).
13.1.4 Relocatable Vector Table for the Peripheral Function
Set the starting address of the DMAC II index in the interrupt vector for the peripheral function interrupt
activating DMAC II.
When using the chained transfer, the relocatable vector table must be located in the RAM.
13.1.5 IRLT Bit in the IIOiIE Register (i=0 to 6, 8 to 11)
When the intelligent I/O interrupt or CAN interrupt is used to activate DMAC II, set the IRLT bit in the IIOiIE
register of the interrupt to "0".
13.2 DMAC II Performance
Function to activate DMAC II is selected by setting the DMA II bit to "1" (DMAC II transfer). DMAC II is
activated by all peripheral function interrupts with the ILVL2 to ILVL0 bits set to "1112" (level 7). These
peripheral function interrupt request signals become DMAC II transfer request signals and the peripheral
function interrupt cannot be used.
When an interrupt request is generated by setting the ILVL2 to ILVL0 bits to "1112" (level 7), DMAC II is
activated regardless of what state the I flag and IPL are in.
13.3 Transfer Data
DMAC II transfers 8-bit or 16-bit data.
• Memory-to-memory transfer : Data is transferred from a desired memory location in a 64-Kbyte space
(Addresses 0000016 to 0FFFF16) to another desired memory location in the same space.
• Immediate data transfer : Immediate data is transferred to a desired memory location in a 64-Kbyte space.
• Calculation transfer : Two 8-bit or16-bit data are added together and the result is transferred to a desired
memory location in a 64-Kbyte space.
When a 16-bit data is transferred to the destination address 0FFFF16, it is transferred to 0FFFF16 and
1000016. The same transfer occurs when the source address is 0FFFF16. Actual transferable space varies
depending on the internal RAM capacity.
13.3.1 Memory-to-memory Transfer
Data transfer between any two memory locations can be:
• a transfer from a fixed address to another fixed address
• a transfer from a fixed address to a relocatable address
• a transfer from a relocatable address to a fixed address
• a transfer from a relocatable address to another relocatable address
When a relocatable address is selected, the address is incremented, after a transfer, for the next transfer.
In a 8-bit transfer, the transfer address is incremented by one. In a 16-bit transfer, the transfer address is
incremented by two.
When a source or destination address exceeds address 0FFFF16 as a result of address incrementation,
the source or destination address returns to address 0000016 and continues incrementation. Maintain
source and destination address at address 0FFFF16 or below.
Rev. 1.10 Oct. 18, 2005 Page 122 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
13. DMACII
13.3.2 Immediate Data Transfer
DMAC II transfers immediate data to any memory location. A fixed or relocatable address can be selected as the destination address. Store the immediate data into SADR. To transfer an 8-bit immediate
data, write the data in the low-order byte of SADR (high-order byte is ignored).
13.3.3 Calculation Transfer
After two memory data or an immediate data and memory data are added together, DMAC II transfers
calculated result to any memory location. SADR must have one memory location address to be calculated or immediate data and OADR must have the other memory location address to be calculated. Fixed
or relocatable address can be selected as source and destination addresses when using a memory +
memory calculation transfer. If the transfer source address is relocatable, the operation address also
becomes relocatable. Fixed or relocatable address can be selected as the transfer destination address
when using an immediate data + memory calculation transfer.
13.4 Transfer Modes
Single and burst transfers are available. The BRST bit in MOD selects transfer method, either single transfer or burst transfer. COUNT determines how many transfers occur. No transfer occurs when COUNT is set
to "000016".
13.4.1 Single Transfer
For every transfer request source, DMAC II transfers one transfer unit of 8-bit or 16-bit data once. When
the source or destination address is relocatable, the address is incremented, after a transfer, for the next
transfer.
COUNT is decremented every time a transfer occurs. When using the end-of-transfer interrupt, the interrupt is acknowledged when COUNT reaches "0".
13.4.2 Burst Transfer
For every transfer request source, DMAC II continuously transfers data the number of times determined
by COUNT. COUNT is decremented every time a transfer occurs. The burst transfer ends when COUNT
reaches "0". The end-of-transfer interrupt is acknowledged when the burst transfer ends if using the endof-transfer interrupt. All interrupts are ignored while the burst transfer is in progress.
13.5 Multiple Transfer
The MULT bit in MOD selects the multiple transfer. When using the multiple transfer, select the memory-tomemory transfer. One transfer request source initiates multiple transfers. The CNT2 to CNT0 bits in MOD
selects the number of transfers from "0012" (once) to "1112" (7 times). Do not set the CNT2 to CNT0 bits to
"0002".
The transfer source and destination addresses for each transfer must be allocated alternately in addresses
following MOD and COUNT. When the multiple transfer is selected, the calculation transfer, burst transfer,
end-of-transfer interrupt and chained transfer cannot be used.
Rev. 1.10 Oct. 18, 2005 Page 123 of 435
REJ09B0162-0110
13. DMACII
M32C/88 Group (M32C/88T)
13.6 Chained Transfer
The CHAIN bit in MOD selects the chained transfer.
The following process initiates the chained transfer.
(1) Transfer, caused by a transfer request source, occurs according to the content of the DMAC II index.
The vectors of the request source indicates where the DMAC II index is allocated. For each request, the
BRST bit selects either single or burst transfer.
(2) When COUNT reaches "0", the contents of CADR1 and CADR0 are written to the vector of the request
source. When the INTE bit in MOD is set to "1", the end-of-transfer interrupt is generated simultaneously.
(3) When the next DMAC II transfer request is generated, transfer occurs according to the contents of the
DMAC II index indicated by the peripheral function interrupt vector rewritten in (2).
Figure 13.4 shows the relocatable vector and DMACII index when the chained transfer is in progress.
For the chained transfer, the relocatable vector table must be located in the RAM.
RAM
INTB
Relocatable Vector
Peripheral I/O interrupt vector causing DMAC II request
Default value of DMAC II is BASE(1).
BASE(1)
DMAC II
Index(1)
(CADR1 and
CADR0)
BASE(2)
The above vector is rewritten to BASE(2)
when a transfer is completed.
Starts at BASE(2) when next request condition
are met.
Transferred according to the DMAC II Index.
BASE(2)
DMAC II
Index(2)
(CADR1 and
CADR0)
BASE(3)
The above vector is rewritten to BASE(3)
when transfer is completed.
Figure 13.4 Relocatable Vector and DMAC II Index
13.7 End-of-Transfer Interrupt
The INTE bit in MOD selects the end-of-transfer interrupt. Set the starting address of the end-of-transfer
interrupt routine in IADR1 and IADR0. The end-of-transfer interrupt is generated when COUNT reaches "0."
Rev. 1.10 Oct. 18, 2005 Page 124 of 435
REJ09B0162-0110
13. DMACII
M32C/88 Group (M32C/88T)
13.8 Execution Time
DMAC II execution cycle is calculated by the following equations:
Multiple transfers: t = 21+ (11 + b + c) x k cycles
Other than multiple transfers: t = 6 + (26 + a + b + c + d) x m + (4 + e) x n cycles
a: If IMM = 0 (source of transfer is immediate data), a = 0;
if IMM = 1 (source of transfer is memory), a = –1
b: If UPDS = 1 (source transfer address is a relocatable address), b = 0;
if UPDS = 0 (source transfer address is a fixed address), b = 1
c: If UPDD = 1 (destination transfer address is a relocatable address), c = 0;
if UPDD = 0 (destination transfer address is a fixed address), c = 1
d: If OPER = 0 (calculation function is not selected), d = 0;
if OPER = 1 (calculation function is selected) and UPDS = 0 (source of transfer is immediate data or fixed
address memory), d = 7;
if OPER = 1 (calculation function is selected) and UPDS = 1 (source of transfer is relocatable address
memory), d = 8
e: If CHAIN = 0 (chained transfer is not selected), e = 0; if CHAIN = 1 (chained transfer is selected), e = 4
m: BRST = 0 (single transfer), m = 1; BRST = 1 (burst transfer), m = the value set in transfer counter
n: If COUNT = 1, n = 0; if COUNT = 2 or more, n = 1
k: Number of transfers set in the CNT2 to CNT0 bits
The equations above are approximations. The number of cycles may vary depending on CPU state, bus
wait state, and DMAC II index allocation.
The first instruction from the end-of-transfer interrupt routine is executed in the eighth cycle after the DMAC
II transfer is completed.
If the end-of-transfer interrupt (transfer counter = 2) occurs with no chained transfer function
after a memory-to-memory transfer occurs with a relocatable source address, fixed destination address,
single transfer and double transfer:
a=-1
b=0
c=1
d=0
e=0
m=1
First DMAC II transfer
t=6+26x1+4x1=36 cycles
Second DMAC II transfer t=6+26x1+4x0=32 cycles
DMAC II transfer request
Program
DMAC II transfer
(First time)
DMAC II transfer request
Program
36 cycles
Transfer counter = 2
Processing the end-of-transfer
interrupt
DMAC II transfer
(Second time)
32 cycles
7 cycles
Transfer counter = 1
Decrement a transfer counter
Transfer counter = 1
Decrement a transfer counter
Transfer counter = 0
Figure 13.5 Transfer Cycle
When an interrupt
request as a DMAC II transfer request source and another interrupt request with higher
_______
priority (e.g., NMI or watchdog timer) are generated simultaneously, the interrupt with higher priority takes
precedence over the DMAC II transfer. The pending DMAC II transfer starts after the interrupt sequence
has been completed.
Rev. 1.10 Oct. 18, 2005 Page 125 of 435
REJ09B0162-0110
14. Timer
M32C/88 Group (M32C/88T)
14. Timer
The microcomputer has eleven 16-bit timers. Five timers A and six timers B have different functions. Each
timer functions independently. The count source for each timer becomes the clock for timer operations
including counting and reloading, etc. Figures 14.1 and 14.2 show block diagrams of timer A and timer B
configuration.
Clock prescaler
1/32
XCIN
fC32
Reset
Set the CPSR bit in the
CPSRF register to "1"
f1 f8 f2n fC32
00
01
10
11
TCK1 and TCK0
TMOD1 and TMOD0
10
Noise
filter
TA0IN
00: Timer mode
10: One-shot timer mode
11: PWM mode
Timer A0 interrupt
Timer A0
01
00
01: Event counter mode
11 TA0TGH and TA0TGL
00
01
10
11
TCK1 and TCK0
TCK1 and TCK0
00
01
10
11
Noise
filter
Timer A1 interrupt
Timer A1
01
00
11
TA2IN
TMOD1 and TMOD0
10
Noise
filter
TA1IN
00: Timer mode
10: One-shot tiemr mode
11: PWM mode
01: Event counter mode
TA1TGH and TA1TGL
00: Timer mode
10: One-shot timer mode
11: PWM mode
TMOD1 and TMOD0
10
01
00
Timer A2 interrupt
Timer A2
01: Event counter mode
11 TA2TGH and TA2TGL
00TCK1 and TCK0
01
10
11
Noise
filter
TA3IN
00: Timer mode
10: One-shot timer mode
11: PWM mode
TMOD1 and TMOD0
10
01
00
Timer A3 interrupt
Timer A3
01: Event counter mode
11 TA3TGH and TA3TGL
00
01
10
11
TA4IN
TCK1 and TCK0
00: Timer mode
10: One-shot timer mode
11: PWM mode
TMOD1 and TMOD0
10
Noise
filter
Timer A4
01
00
01: Event counter mode
11 TA4TGH and TA4TGL
Timer B2 overflow
or underflow signal
CST: Bit in the TCSPR Register
TCK1 and TCK0, TMOD1 and TMOD0: Bits in the TAiMR Register (i=0 to 4)
TAiTGH and TAiTGL: Bits in the ONSF Register or TRGSR Register
Figure 14.1 Timer A Configuration
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 126 of 435
Timer A4 interrupt
14. Timer
M32C/88 Group (M32C/88T)
Clock prescaler
1/32
XCIN
fC32
Reset
Set the CPSR bit in the
CPSRF register to "1"
f1 f8 f2n fC32
00
01
10
11
Timer B2 overflow or underflow signal
(to a count source of Timer A)
TCK1 to TCK0
00: Timer mode
10: Pulse width measurement mode
TMOD1 and TMOD0
TB0IN
Noise
filter
00
01
10
11
TB1IN
Timer B0
TCK1
1
01:Event counter mode
TMOD1 and TMOD0
0
TCK1
01:Event counter mode
TCK1 and TCK0
00: Timer mode
10: Pulse width measurement mode
1
TMOD1 and TMOD0
0
01:Event counter mode
TCK1 and TCK0
00: Timer mode
10: Pulse width measurement mode
TMOD1 and TMOD0
Noise
filter
00
01
10
11
00
01
10
11
TB5IN
0
Timer B3
TCK1
TCK1 and TCK0
01:Event counter mode
1
TMOD1 and TMOD0
Timer B4
0
TCK1
TCK1 and TCK0
Timer B4 interrupt
01:Event counter mode
00: Timer mode
10: Pulse width measurement mode
1
Noise
filter
TMOD1 and TMOD0
Timer B5
0
TCK1
01:Event counter mode
CST: Bit in the TCSPR Register
TCK1 and TCK0, TMOD1 and TMOD0: Bits in the TBiMR Register (i=0 to 5)
Figure 14.2 Timer B Configuration
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Timer B3 interrupt
00: Timer mode
10: Pulse width measurement mode
Noise
filter
TB4IN
Timer B2 interrupt
Timer B2
1
TB3IN
Timer B1 interrupt
Timer B1
TCK1
00
01
10
11
Timer B0 interrupt
00: Timer mode
10: Pulse width measurement mode
Noise
filter
TB2IN
0
TCK1 and TCK0
Noise
filter
00
01
10
11
1
Page 127 of 435
Timer B5 interrupt
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
14.1 Timer A
Figure 14.3 shows a block diagram of the timer A. Figures 14.4 to 14.7 show registers associated with the
timer A.
The timer A supports the following four modes. Except in event counter mode, all timers A0 to A4 have the
same function. The TMOD1 and TMOD0 bits in the TAiMR register (i=0 to 4) determine which mode is
used.
• Timer mode: The timer counts an internal count source.
• Event counter mode: The timer counts an external pulse or an overflow and underflow of other timers.
• One-shot timer mode: The timer outputs one valid pulse until a counter value reaches "000016".
• Pulse width modulation mode: The timer continuously outputs desired pulse widths.
Table 14.1 lists TAiOUT pin settings when used as an output. Table 14.2 lists TAiIN and TAiOUT pin settings
when used as an input.
Select clock
High-Order Bits of Data Bus
Select Count Source
f1
f8
f2n(1)
fC32
TAiIN
00
01
10
11
TCK1 and
TCK0
• Timer Mode: TMOD1 and TMOD0=00, MR2=0
• One-Shot Timer Mode: TMOD1 and TMOD0=10
• Pulse Width Modulation Mode:
TMOD1 and TMOD0=11
TMOD1 and TMOD0,
MR2
• Timer Mode (gate function):
TMOD1 and TMOD0=00, MR2=1
• Event Counter Mode:TMOD1 and TMOD0=01
Polarity
Selector
Low-Order Bits of Data Bus
8 loworder
bits
Reload Register
A
A
Counter
Increment / decrement
Always decrement except
in event counter mode
TAiS
00
01
TB2 Overflow(2)
10
TAj Overflow(2)
11
(2)
TAk Overflow
Decrement
00
01
11
01
TAiTGH and TAiTGL
TAiUD
TMOD1 and TMOD0
0
1
Pulse Output
MR2
TAiOUT
Toggle Flip Flop
i=0 to 4
j=i-1, except j=4 if i=0
k=i+1, except k=0 if i=4
NOTES:
1. The CNT3 to CNT0 bits in the TCSPR register select
no division (n=0) or divide-by-2n (n=1 to 15).
2. Overflow or underflow signal
TAi
Timer A0
Timer A1
Timer A2
Timer A3
Timer A4
Addresses
034716 034616
034916 034816
034B16 034A16
034D16 034C16
034F16 034E16
TCK1 and TCK0, TMOD1 and TMOD0, MR2 and MR1: Bits in the TAiMR register
TAiTGH and TAiTGL: Bits in the ONSF register if i=0 or bits in the TRGSR register if i=1 to 4
TAiS: Bits in the TABSR register
TAiUD: Bits in the UDF register
Figure 14.3 Timer A Block Diagram
Rev. 1.10 Oct. 18, 2005 Page 128 of 435
REJ09B0162-0110
8 highorder
bits
TAj
Timer A4
Timer A0
Timer A1
Timer A2
Timer A3
TAk
Timer A1
Timer A2
Timer A3
Timer A4
Timer A0
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
Timer Ai Register (i=0 to 4)(1)
b15
b8 b7
b0
Symbol
TA0 to TA2
TA3, TA4
Address
034716-034616, 034916-034816, 034B16-034A16
034D16-034C16, 034F16-034E16
Mode
Function
After Reset
Indeterminate
Indeterminate
Setting Range
RW
Timer Mode
If setting value is n, count source
is divided by n+1.
000016 to FFFF16 RW
Event Counter
Mode(2)
If setting value is n, count source
is divided by FFFF16 - n+1 when
the counter is incremented
and by n+1 when the counter is
decremented.
000016 to FFFF16 RW
One-shot Timer
Mode(4)
If setting value is n, count source
is divided by n, then stops.
000016 to FFFF16(3) WO
If count source frequency is fj
Pulse Width
and setting value of the TAi
Modulation Mode(5) register is n,
PWM cycle: (216-1) / fj
(16-bit PWM)
"H" width of PWM pulse: n / fj
Pulse Width
Modulation Mode(5)
(8-bit PWM)
If count source frequency is fj,
setting value of high-order bits in
the TAi register is n and setting
value of low-order bits in the TAi
register is m,
PWM cycle: (28-1)x(m+1) / fj
"H" width of PWM pulse: (m+1)n / fj
000016 to FFFE16(3) WO
0016 to FE16(3)
(High-order
address bits)
0016 to FF16(3)
(Low-order
address bits)
WO
fj : f1, f8, f2n, fC32
NOTES:
1. Use 16-bit data for reading and writing.
2. The TAi register counts how many pulse inputs are provided externally or how many times another
timer counter overflows and underflows.
3. Use the MOV instruction to set the TAi register.
4. When the TAi register is set to "000016", the timer counter does not start and the timer Ai interrupt
request is not generated.
5. When the TAi register is set to "000016", the pulse width modulator does not operate and the TAiOUT
pin is held "L". The TAi interrupt request is also not generated. The same situation occurs in 8-bit
pulse width modulator mode if the 8 high-order bits in the TAi register are set to "0016".
Figure 14.4 TA0 to TA4 Registers
Rev. 1.10 Oct. 18, 2005 Page 129 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
Timer Ai Mode Register (i=0 to 4)
b7
b6
b5
b4
b3
b2
b1
b0
0
Symbol
TA0MR to TA4MR
Bit
Symbol
Address
035616, 035716, 035816, 035916, 035A16
Bit Name
After Reset
0016
Function
RW
b1b0
0 0: Timer mode
0 1: Event counter mode
1 0: One-shot timer mode
1 1: Pulse width modulation
(PWM) mode
RW
Operating Mode
Select Bit
Reserved Bit
Set to "0"
RW
TMOD0
TMOD1
(b3)
MR1
RW
RW
Function varies depending on
operating mode
MR2
MR3
RW
RW
TCK0
Count Source
Select Bit
Function varies depending on
operating mode
TCK1
RW
RW
Count Start Flag
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
TABSR
Bit
Symbol
Address
034016
After Reset
0016
Bit Name
Function
RW
TA0S
Timer A0 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA1S
Timer A1 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA2S
Timer A2 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA3S
Timer A3 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA4S
Timer A4 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB0S
Timer B0 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB1S
Timer B1 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB2S
Timer B2 Count
Start Flag
0: Stops counting
1: Starts counting
RW
Figure 14.5 TA0MR to TA4MR Registers and TABSR Register
Rev. 1.10 Oct. 18, 2005 Page 130 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
Up/Down Flag(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
UDF
Address
034416
After Reset
0016
Bit
Symbol
Bit Name
TA0UD
Timer A0
Up/Down Flag(2)
0: Decrement
1: Increment
RW
TA1UD
Timer A1
Up/Down Flag(2)
0: Decrement
1: Increment
RW
TA2UD
Timer A2
Up/Down Flag(2)
0: Decrement
1: Increment
RW
TA3UD
Timer A3
Up/Down Flag(2)
0: Decrement
1: Increment
RW
TA4UD
Timer A4
Up/Down Flag(2)
0: Decrement
1: Increment
RW
Function
0: Disables two-phase pulse signal
Timer A2 Two-Phase
processing function
Pulse Signal Processing
1: Enables two-phase pulse signal
Function Select Bit(3)
processing function
0: Disables two-phase pulse signal
Timer A3 Two-Phase
processing function
Pulse Signal Processing 1: Enables
two-phase pulse signal
(3)
Function Select Bit
processing function
0: Disables two-phase pulse signal
Timer A4 Two-Phase
processing function
Pulse Signal Processing
1: Enables two-phase pulse signal
Function Select Bit(3)
processing function
TA2P
TA3P
TA4P
RW
WO
WO
WO
NOTES:
1. Use the MOV instruction to set the UDF register.
2. This bit is enabled when the MR2 bit in the TAiMR register (i=0 to 4) is set to "0" (the UDF register
causes increment/decrement switching) in event counter mode.
3. Set this bit to "0" when not using the two-phase pulse signal processing function.
One-Shot Start Flag
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
ONSF
Bit
Symbol
Address
034216
After Reset
0016
Bit Name
Function
RW
TA0OS
Timer A0 One-Shot
Start Flag(1)
0: In an idle state
1: Starts the timer
RW
TA1OS
Timer A1 One-Shot
Start Flag(1)
0: In an idle state
1: Starts the timer
RW
TA2OS
Timer A2 One-Shot
Start Flag(1)
0: In an idle state
1: Starts the timer
RW
TA3OS
Timer A3 One-Shot
Start Flag(1)
0: In an idle state
1: Starts the timer
RW
TA4OS
Timer A4 One-Shot
Start Flag(1)
0: In an idle state
1: Starts the timer
RW
TAZIE
Z-Phase Input Enable Bit
0: Disables Z-phase input
1: Enables Z-phase input
RW
b7b6
TA0TGL
Timer A0 Event/Trigger
Select Bit
TA0TGH
NOTES:
1. When read, this bit is set to "0".
2. Overflow or underflow.
Figure 14.6 UDF Register and ONSF Register
Rev. 1.10 Oct. 18, 2005 Page 131 of 435
REJ09B0162-0110
0 0: Selects an input to the TA0IN pin RW
0 1: Selects TB2 overflows(2)
1 0: Selects TA4 overflows(2)
RW
1 1: Selects TA1 overflows(2)
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
Trigger Select Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset
TRGSR
034316
0016
Bit
Symbol
Function
RW
0 0: Selects an input to the TA1IN pin
0 1: Selects TB2 overflows(1)
1 0: Selects TA0 overflows(1)
1 1: Selects TA2 overflows(1)
RW
Bit Name
b1 b0
TA1TGL
Timer A1 Event/Trigger
Select Bit
TA1TGH
RW
b3 b2
TA2TGL
Timer A2 Event/Trigger
Select Bit
TA2TGH
0 0: Selects an input to the TA2IN pin
0 1: Selects TB2 overflows(1)
1 0: Selects TA1 overflows(1)
1 1: Selects TA3 overflows(1)
RW
RW
b5 b4
TA3TGL
Timer A3 Event/Trigger
Select Bit
TA3TGH
0 0: Selects an input to the TA3IN pin
0 1: Selects TB2 overflows(1)
1 0: Selects TA2 overflows(1)
1 1: Selects TA4 overflows(1)
RW
RW
b7 b6
TA4TGL
Timer A4 Event/Trigger
Select Bit
TA4TGH
0 0: Selects an input to the TA4IN pin
0 1: Selects TB2 overflows(1)
1 0: Selects TA3 overflows(1)
1 1: Selects TA0 overflows(1)
RW
RW
NOTE:
1. Overflow or underflow.
Count Source Prescaler Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
TCSPR
Bit
Symbol
Address
035F16
Bit Name
After Reset(2)
0XXX 00002
Function
RW
CNT0
CNT1
Divide Ratio Select Bit(1)
CNT2
If setting value is n, f2n is the
main clock, on-chip oscillator or
PLL clock divided by 2n.
Not divided if n=0.
CST
RW
RW
RW
CNT3
(b6 - b4)
RW
Reserved Bit
When read,
its content is indeterminate
RO
Operation Enable Bit
0: Stops a divider
1: Starts a divider
RW
NOTES:
1. Set the CST bit to "0" before the CNT3 to CNT0 bits are rewritten.
2. The TCSPR register maintains values set before reset, even after software reset or watchdog timer
reset has performed.
Figure 14.7 TRGSR Register and TCSPR Register
Rev. 1.10 Oct. 18, 2005 Page 132 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
Table 14.1 Pin Settings for Output from TAiOUT Pin (i=0 to 4)
Pin
Setting
PS1, PS2 Registers
PSL1, PSL2 Registers
PSC Register
P70/TA0OUT(1)
PS1_0= 1
PSL1_0=1
PSC_0= 0
P72/TA1OUT
PS1_2= 1
PSL1_2=1
PSC_2= 0
P74/TA2OUT
PS1_4= 1
PSL1_4=0
PSC_4= 0
P76/TA3OUT
PS1_6= 1
PSL1_6=1
PSC_6= 0
P80/TA4OUT
PS2_0= 1
PSL2_0=0
–
NOTE:
1. P70/TA0OUT is a port for the N-channel open drain output.
Table 14.2 Pin Settings for Input to TAiIN and TAiOUT Pins (i=0 to 4)
Pin
Setting
PS1, PS2 Registers
PD7, PD8 Registers
P70/TA0OUT
PS1_0=0
PD7_0=0
P71/TA0IN
PS1_1=0
PD7_1=0
P72/TA1OUT
PS1_2=0
PD7_2=0
P73/TA1IN
PS1_3=0
PD7_3=0
P74TA2OUT
PS1_4=0
PD7_4=0
P75/TA2IN
PS1_5=0
PD7_5=0
P76TA3OUT
PS1_6=0
PD7_6=0
P77/TA3IN
PS1_7=0
PD7_7=0
P80/TA4OUT
PS2_0=0
PD8_0=0
P81/TA4IN
PS2_1=0
PD8_1=0
Rev. 1.10 Oct. 18, 2005 Page 133 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
14.1.1 Timer Mode
In timer mode, the timer counts an internally generated count source (see Table 14.3). Figure 14.8
shows the TAiMR register (i=0 to 4) in timer mode.
Table 14.3 Timer Mode Specifications
Item
Specification
Count Source
f1, f8, f2n(1), fC32
Counting Operation
• The timer decrements a counter value
When the timer counter underflows, content of the reload register is reloaded into the
count register and counting resumes.
Divide Ratio
1/(n+1)
n: setting value of the TAi register (i=0 to 4)
000016 to FFFF16
Counter Start Condition
The TAiS bit in the TABSR register is set to "1" (starts counting)
Counter Stop Condition
The TAiS bit is set to "0" (stops counting)
Interrupt Request Generation Timing The timer counter underflows
TAiIN Pin Function
Programmable I/O port or gate input
TAiOUT Pin Function
Programmable I/O port or pulse output
Read from Timer
The TAi register indicates counter value
Write to Timer
• While the timer counter stops, the value written to the TAi register is also written to
both reload register and counter
• While counting, the value written to the TAi register is written to the reload register
(It is transferred to the counter at the next reload timing)
Selectable Function
• Gate function
Input signal to the TAiIN pin determines whether the timer counter starts or stops counting
• Pulse output function
The polarity of the TAiOUT pin is inversed whenever the timer counter underflows
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Rev. 1.10 Oct. 18, 2005 Page 134 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
Timer Ai Mode Register (i=0 to 4) (Timer Mode)
b7
b6
b5
0
b4
b3
b2
b1
b0
Symbol
TA0MR to TA4MR
0 0 0
Bit
Symbol
Address
035616, 035716, 035816, 035916, 035A16
Bit Name
TMOD0
Operating Mode
Select Bit
Function
b1b0
RW
RW
0 0: Timer mode
TMOD1
(b2)
After Reset
0016
RW
Reserved Bit
Set to "0"
RW
b4b3
MR1
Gate Function
Select Bit
MR2
MR3
0 X: Gate function disabled(1)
RW
(TAiIN pin is a programmable I/O pin)
1 0: Timer counts only while the
TAiIN pin is held "L"
RW
1 1: Timer counts only while the
TAiIN pin is held "H"
Set to "0" in timer mode
RW
b7b6
TCK0
Count Source
Select Bit
TCK1
0 0: f1
0 1: f8
1 0: f2n(2)
1 1: fC32
RW
RW
NOTES:
1. X can be set to either "0" or "1".
2. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Figure 14.8 TA0MR to TA4MR Registers
Rev. 1.10 Oct. 18, 2005 Page 135 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
14.1.2 Event Counter Mode
In event counter mode, the timer counts how many external signals are applied or how many times
another timer counter overflows and underflows. The timers A2, A3 and A4 can count externally generated two-phase signals. Table 14.4 lists specifications in event counter mode (when not handling a twophase pulse signal). Table 14.5 lists specifications in event counter mode (when handling a two-phase
pulse signal with the timers A2, A3 and A4). Figure 14.9 shows the TAiMR register (i=0 to 4) in event
counter mode.
Table 14.4 Event Counter Mode Specifications (When Not Processing Two-phase Pulse Signal)
Item
Count Source
Specification
• External signal applied to the TAiIN pin (i = 0 to 4) (valid edge can be selected by program)
• Timer B2 overflow or underflow signal, timer Aj overflow or underflow signal (j=i-1,
except j=4 if i=0) and timer Ak overflow or underflow signal (k=i+1, except k=0 if i=4)
Counting Operation
• External signal and program can determine whether the timer increments or decrements a counter value
• When the timer counter underflows or overflows, content of the reload register is
reloaded into the count register and counting resumes. When the free-running count
function is selected, the timer counter continues running without reloading.
Divide Ratio
• 1/(FFFF16 - n + 1) for counter increment
Counter Start Condition
The TAiS bit in the TABSR register is set to "1" (starts counting)
Counter Stop Condition
The TAiS bit is set to "0" (stops counting)
• 1/(n + 1) for counter decrement
n : setting value of the TAi register 0000 16 to FFFF16
Interrupt Request Generation Timing The timer counter overflows or underflows
TAiIN Pin Function
Programmable I/O port or count source input
TAiOUT Pin Function
Programmable I/O port, pulse output or input selecting a counter increment or decrement
Read from Timer
The TAi register indicates counter value
Write to Timer
• When the timer counter stops, the value written to the TAi register is also written to
both reload register and counter
• While counting, the value written to the TAi register is written to the reload register
(It is transferred to the counter at the next reload timing)
Selectable Function
• Free-running count function
Content of the reload register is not reloaded even if the timer counter overflows or
underflows
• Pulse output function
The polarity of the TAiOUT pin is inversed whenever the timer counter overflows or
underflows
Rev. 1.10 Oct. 18, 2005 Page 136 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
Table 14.5 Event Counter Mode Specifications (When Processing Two-phase Pulse Signal on
Timer A2, A3 and A4)
Item
Specification
Count Source
Two-phase pulse signal applied to the TAiIN and TAiOUT pins (i = 2 to 4)
Counting Operation
• Two-phase pulse signal determines whether the timer increments or decrements a
counter value
• When the timer counter overflows or underflows, content of the reload register is
reloaded into the count register and counting resumes. With the free-running count
function, the timer counter continues running without reloading.
Divide Ratio
• 1/ (FFFF16 - n + 1) for counter increment
• 1/ (n + 1) for counter decrement
n : setting value of the TAi register 000016 to FFFF16
Counter Start Condition
The TAiS bit in the TABSR register is set to "1" (starts counting)
Counter Stop Condition
The TAiS bit is set to "0" (stops counting)
Interrupt Request Generation Timing The timer counter overflows or underflows
TAiIN Pin Function
Two-phase pulse signal is applied
TAiOUT Pin Function
Two-phase pulse signal is applied
Read from Timer
The TAi register indicates the counter value
Write to Timer
• When the timer counter stops, the value written to the TAi register is also written to
both reload register and counter
• While counting, the value written to the TAi register is written to the reload register
(It is transferred to the counter at the next reload timing)
Selectable
Function(1)
• Normal processing operation (the timer A2 and timer A3)
While a high-level ("H") signal is applied to the TAjOUT pin (j = 2 or 3), the timer
increments a counter value on the rising edge of the TAjIN pin or decrements a
counter on the falling edge.
TAjOUT
TAjIN
Increment Increment Increment Decrement Decrement Decrement
• Multiply-by-4 processing operation (the timer A3 and timer A4)
While an "H" signal is applied to the TAkOUT pin (k = 3 or 4) on the rising edge of the
TAkIN pin, the timer increments a counter value on the rising and falling edges of the
TAkOUT and TAkIN pins.
While an "H" signal is applied to the TAkOUT pin on the falling edge of the TAkIN pin, the
timer decrements a counter value on the rising and falling edges of the TAkOUT and
TAkIN pins.
TAkOUT
TAkIN
Increment on all edges
Decrement on all edges
NOTE:
1. Only timer A3 operation can be selected. The timer A2 is for the normal processing operation. The timer A4 is
for the multiply-by-4 operation.
Rev. 1.10 Oct. 18, 2005 Page 137 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
Timer Ai Mode Register (i=0 to 4) (Event Counter Mode)
b7
b6
b5
0
b4
b3
b2
b1
b0
0 0 1
Symbol
TA0MR to TA4MR
Bit
Symbol
Address
035616, 035716, 035816, 035916, 035A16
Bit Name
TMOD0
Operating Mode
Select Bit
After Reset
0016
Function
Function
(When not processing
two-phase pulse signal)
(When processing
two-phase pulse signal)
RW
RW
b1b0
0 1: Event counter mode(1)
RW
TMOD1
Reserved Bit
Set to "0"
RW
MR1
Count Polarity
Select Bit(2)
0: Counts falling edges
of an external signal
Set to "0"
1: Counts rising edges
of an external signal
RW
MR2
Increment/Decrement 0: UDF registser
setting
Switching Source
1: Input signal to
Select Bit
TAiOUT pin(3)
(b2)
Set to "1"
RW
MR3
Set to "0" in event counter mode
RW
TCK0
Count Operation
Type Select Bit
RW
TCK1
Two-Phase Pulse
Set to "0"
Signal Processing
Operation Select Bit(4,5)
0: Reloading
1: Free running
0: Normal processing
operation
RW
1: Multiply-by-4
processing operation
NOTES:
1. The TAiTGH and TAiTGL bits in the ONSF or TRGSR register determine the count source in the event
counter mode.
2. MR1 bit setting is enabled only when counting how many times external signals are applied.
3. The timer decrements a counter value when an "L" signal is applied to the TAiOUT pin and the timer
increments a counter value when an "H" signal is applied to the TAiOUT pin.
4. The TCK1 bit is enabled only in the TA3MR register.
5. For two-phase pulse signal processing, set the TAjP bit in the UDF register (j=2 to 4) to "1" (two-phase
pulse signal processing function enabled). Also, set the TAjTGH and TAjTGL bits to "002" (input to the
TAjIN pin).
Figure 14.9 TA0MR to TA4MR Registers
Rev. 1.10 Oct. 18, 2005 Page 138 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
14.1.2.1 Counter Reset by Two-Phase Pulse Signal Processing
Z-phase input resets the timer counter when processing a two-phase pulse signal.
This function can be used in timer A3 event counter mode, two-phase pulse signal processing, free_______
running count operation type or multiply-by-4 processing. The Z-phase signal is applied to the INT2 pin.
When the TAZIE bit in the ONSF register is set to "1" (Z-phase input enabled), Z-phase input can
reset the timer counter. To reset the counter by a Z-phase input, set the TA3 register to "000016"
beforehand.
_______
Z-phase input is enabled when the edge of the signal applied to the INT2 pin is detected. The POL bit
in the INT2IC register can determine edge polarity. The Z-phase must have a pulse width of one timer
A3 count source cycle or more . Figure 14.10 shows two-phase pulses (A-phase and B-phase) and
the Z-phase.
Z-phase input resets the timer counter in the next count source following Z-phase input. Figure 14.11
shows the counter reset timing.
Timer A3 interrupt request is generated twice continuously when a timer A3 overflow or underflow,
_______
and a counter reset by INT2 input occur at the same time. Do not use the timer A3 interrupt request
when this function is used.
TA3OUT
(A-phase)
TA3IN
(B-phase)
Count source
INT2 (1)
(Z-phase)
Pulse width of one count source cycle
or more is required
NOTE:
1. When the rising edge of INT2 is selected.
Figure 14.10 Two-Phase Pulse (A-phase and B-phase) and Z-phase
TA3OUT
(A-phase)
TA3IN
(B-phase)
Count source
INT2 (1)
(Z-phase)
Counter value
m
m+1
1
Timer counter is reset
at this timing
Figure 14.11 Counter Reset Timing
Rev. 1.10 Oct. 18, 2005 Page 139 of 435
REJ09B0162-0110
2
3
4
5
NOTE:
1. When the rising edge of INT2 is selected.
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
14.1.3 One-Shot Timer Mode
In one-shot timer mode, the timer operates only once for each trigger (see Table 14.6). Once a trigger
occurs, the timer starts and continues operating for a desired period. Figure 14.12 shows the TAiMR
register (i=0 to 4) in one-shot timer mode.
Table 14.6 One-Shot Timer Mode Specifications
Item
Specification
Count Source
f1, f8, f2n(1), fC32
Counting Operation
• The timer decrements a counter value
When the timer counter reaches "000016", it stops counting after reloading.
If a trigger occurs while counting, content of the reload register is reloaded into the
count register and counting resumes.
Divide Ratio
1/n
n : setting value of the TAi register (i=0 to 4) 000016 to FFFF16,
Counter Start Condition
The TAiS bit in the TABSR register is set to "1" (starts counting) and following triggers
but the timer counter does not run if n=000016
occur:
• External trigger input is provided
• Timer counter overflows or underflows
• The TAiOS bit in the ONSF register is set to "1" (timer started)
Counter Stop Condition
• After the timer counter has reached "000016" and is reloaded
• When the TAiS bit is set to "0" (stops counting)
Interrupt Request Generation Timing The timer counter reaches "000016"
TAiIN Pin Function
Programmable I/O port or trigger input
TAiOUT Pin Function
Programmable I/O port or pulse output
Read from Timer
The value in the TAi register is indeterminate when read
Write to Timer
• When the timer counter stops, the value written to the TAi register is also written to
both reload register and counter
• While counting, the value written to the TAi register is written to the reload register
(It is transferred to the counter at the next reload timing)
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Rev. 1.10 Oct. 18, 2005 Page 140 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
Timer Ai Mode Register (i=0 to 4) (One-Shot Timer Mode)
b7
b6
b5
0
b4
b3
b2
b1
b0
Symbol
0 1 0
TA0MR to TA4MR
Bit
Symbol
Address
035616, 035716, 035816, 035916, 035A16
Bit Name
TMOD0
Operating Mode
Select Bit
After Reset
0016
Function
b1b0
RW
1 0: One-shot timer mode
TMOD1
(b2)
RW
RW
Reserved Bit
Set to "0"
MR1
External Trigger Select 0: Falling edge of input signal to TAiIN pin
RW
Bit(1)
1: Rising edge of input signal to TAiIN pin
MR2
Trigger Select Bit
MR3
Set to "0" in the one-shot timer mode
0: TAiOS bit setting is enabled
1: Selected by the TAiTGH and
TAiTGL bits
b7b6
TCK0
Count Source
Select Bit
TCK1
0 0: f1
0 1: f8
1 0: f2n(2)
1 1: fC32
RW
RW
RW
RW
NOTES:
1. The MR1 bit setting is enabled only when the TAiTGH and TAiTGL bits in the TRGSR register are set
to "002" (input to the TAiIN pin). The MR1 bit can be set to either "0" or "1" when the TAiTGH and
TAiTGL bits are set to "012" (TB2 overflow and underflow), "102" (TAi overflow and underflow) or
"112" (TAi overflow and underflow).
2. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Figure 14.12 TA0MR to TA4MR Registers
Rev. 1.10 Oct. 18, 2005 Page 141 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
14.1.4 Pulse Width Modulation Mode
In pulse width modulation mode, the timer outputs pulse of desired width continuously (see Table 14.7).
The timer counter functions as either 16-bit pulse width modulator or 8-bit pulse width modulator. Figure
14.13 shows the TAiMR register (i=0 to 4) in pulse width modulation mode. Figures 14.14 and 14.15
show examples of how a 16-bit pulse width modulator operates and of how an 8-bit pulse width modulator
operates.
Table 14.7 Pulse Width Modulation Mode Specifications
Item
Specification
Count Source
f1, f8, f2n(1), fC32
Counting Operation
• The timer decrements a counter value
(The counter functions as an 8-bit or a 16-bit pulse width modulator)
Content of the reload register is reloaded on the rising edge of PWM pulse and counting continues.
The timer is not affected by a trigger that is generated during counting.
16-Bit PWM
• "H" width = n / fj
n : setting value of the TAi register
000016 to FFFE16
fj : count source frequency
• Cycle = (216-1) / fj fixed
8-Bit PWM
• "H" width = n x (m+1) / fj
• Cycles = (28-1) x (m+1) / fj
m : setting value of low-order bit address of the TAi register
n : setting value of high-order bit address of the TAi register
Counter Start Condition
0016 to FF16
0016 to FE16
• External trigger input is provided
• Timer counter overflows or underflows
• The TAiS bit in the TABSR register is set to "1" (starts counting)
Counter Stop Condition
The TAiS bit is set to "0" (stops counting)
Interrupt Request Generation Timing On the falling edge of the PWM pulse
TAiIN Pin Function
Programmable I/O port or trigger input
TAiOUT Pin Function
Pulse output
Read from Timer
The value in the TAi register is indeterminate when read
Write to Timer
• When the timer counter stops, the value written to the TAi register is also written to
both reload register and counter
• While counting, the value written to the TAi register is written to the reload register
(It is transferred to the counter at the next reload timing)
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Rev. 1.10 Oct. 18, 2005 Page 142 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
Timer Ai Mode Register (i=0 to 4) (Pulse Width Modulator Mode)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
TA0MR to TA4MR
0 1 1
Bit
Symbol
Address
035616, 035716, 035816, 035916, 035A16
Bit Name
TMOD0
Operating Mode
Select Bit
TMOD1
After Reset
0016
Function
b1b0
1 1: Pulse width modulation (PWM)
mode
RW
RW
Reserved Bit
Set to "0"
External Trigger Select
Bit(1)
0: Falling edge of input signal to TAiIN pin
RW
1: Rising edge of input signal to TAiIN pin
(b2)
MR1
RW
RW
MR2
Trigger Select Bit
0: TAiS bit setting is enabled
1: Selected by the TAiTGH and
TAiTGL bits
MR3
16/8-Bit PWM Mode
Select Bit
0: Functions as a 16-bit pulse width modulator
RW
1: Functions as an 8-bit pulse width modulator
b7b6
TCK0
Count Source
Select Bit
TCK1
0 0: f1
0 1: f8
1 0: f2n(2)
1 1: fC32
RW
RW
RW
NOTES:
1. MR1 bit setting is enabled only when the TAiTGH and TAiTGL bits in the TRGSR register are set to
"002" (input to the TAiIN pin). The MR1 bit can be set to either "0" or "1" when the TAiTGH and
TAiTGL bits are set to "012" (TB2 overflow and underflow), "102" (TAi overflow and underflow) or
"112" (TAi overflow and underflow).
2. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Figure 14.13 TA0MR to TA4MR Registers
Rev. 1.10 Oct. 18, 2005 Page 143 of 435
REJ09B0162-0110
14. Timer (Timer A)
M32C/88 Group (M32C/88T)
When the reload register is set to "000316" and an external trigger (on rising edge
of a signal applied to the TAiIN pin) is selected
1 / fj X (216 – 1)
Count source
“H”
Signal applied
to TAiIN pin
“L”
No trigger occurs by this signal
1 / fi X n
“H”
PWM pulse output
from TAiOUT pin
“L”
“1”
IR bit in TAiIC register
“0”
fj : Count source frequency
(f1, f8, f2n(1), fC32)
Set to "0" by an interrupt request acknowledgement or by program
n=000016 to FFFE16
i=0 to 4
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Figure 14.14 16-bit Pulse Width Modulator Operation
When 8 high-order bits of the reload register are set to "0216", 8 low-order bits of
the reload register are set to "0216" and an external trigger (on falling edge of a
signal applied to the TAiIN pin) is selected
1 / fj X (m + 1) X (28 – 1)
Count source(1)
Signal applied to
TAiIN pin
“H”
“L”
AAAAAAAAAAAAAAA
1 / fj X (m + 1)
Underflow signal of
8-bit prescaler(2)
“H”
“L”
1 / fj X (m + 1) X n
PWM pulse output
from TAiOUT pin
“H”
“L”
“1”
IR bit in TAiIC register
“0”
fj : Count source frequency
(f1, f8, f2n(3), fC32)
Set to "0" by an interrupt request
acknowledgement or by program
m=0016 to FF16, n=0016 to FE16
i=0 to 4
NOTES:
1. 8-bit prescaler counts a count source.
2. 8-bit pulse width modulator counts underflow signals of the 8-bit prescaler.
3. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Figure 14.15 8-bit Pulse Width Modulator Operation
Rev. 1.10 Oct. 18, 2005 Page 144 of 435
REJ09B0162-0110
14. Timer (Timer B)
M32C/88 Group (M32C/88T)
14.2 Timer B
Figure 14.16 shows a block diagram of the timer B. Figures 14.17 to 14.19 show registers associated with
the timer B. The timer B supports the following three modes. The TMOD1 and TMOD0 bits in the TBiMR
register (i=0 to 5) determine which mode is used.
• Timer mode : The timer counts an internal count source.
• Event counter mode : The timer counts pulses from an external source or overflow and underflow of
another timer.
• Pulse period/pulse width measurement mode : The timer measures pulse period or pulse width of an
external signal.
Table 14.8 lists TBiIN pin settings.
High-order Bits of Data Bus
Select Clock Source
Low-order Bits of Data Bus
TCK1 and
TCK0
00
00: Timer Mode
f1
TMOD1 and
01: Pulse Period/Pulse Width TMOD0
01
f8
Measurement Mode
f2n(1) 10
fc32 11
01: Event
TCK1
Counter Mode
TBj Overflow
1
Signal(2,3)
8 highorder
bits
Reload Register
Counter
TBiS
0
Polarity Switching
and Edge Pulse
TBiIN
8 low-order
bits
Counter Reset Circuit
i=0 to 5
NOTES:
1. The CNT3 to CNT0 bits in the TCSPR register select no
division (n=0) or divide-by-2n (n=1 to 15).
2. Overflow signal or underflow signal
3. j=i-1, except j=2 when i=0 j=5 when i=3
TBi
Timer B0
Timer B1
Timer B2
Timer B3
Timer B4
Timer B5
Address
035116 035016
035316 035216
035516 035416
031116 031016
031316 031216
031516 031416
TBj
Timer B2
Timer B0
Timer B1
Timer B5
Timer B3
Timer B4
TCK1 and TCK0, TMOD1 and TMOD0: Bits in the TBiMR Register
TBiS: Bits in the TABSR and the TBSR Register
Figure 14.16 Timer B Block Diagram
Timer Bi Register(1) (i=0 to 5)
b15
b8 b7
b0
Symbol
TB0 to TB2
TB3 to TB5
Mode
Address
035116 - 035016, 035316 - 035216, 035516 - 035416
After Reset
Indeterminate
031116 - 031016, 031316 - 031216, 031516 - 031416
Indeterminate
Function
Setting Range
Timer Mode
If setting value is n, a count source 000016 to FFFF16 RW
is divided by n+1
Event Counter
Mode
If setting value is n, a count source 000016 to FFFF16 RW
is divided by n+1(2)
Pulse Period/Pulse A count source is incremented
Width Measurement between one valid edge and
Mode
another valid edge of TBiIN pulse
NOTES:
1. Use 16-bit data for reading and writing.
2. The TBi register counts how many pulse are input externally or how many times another timer
counter overflows and underflows.
Figure 14.17 TB0 to TB5 Registers
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
RW
Page 145 of 435
RO
14. Timer (Timer B)
M32C/88 Group (M32C/88T)
Timer Bi Mode Register (i=0 to 5)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
TB0MR to TB5MR
Bit
Symbol
Address
After Reset
035B16, 035C16, 035D16, 031B16, 031C16, 031D16 00XX 00002
Bit Name
Function
RW
b1b0
TMOD0
Operating Mode
Select Bit
TMOD1
0 0: Timer mode
RW
0 1: Event counter mode
1 0: Pulse period measurement mode,
pulse width measurement mode
RW
1 1: Do not set to this value
MR0
RW
MR1
Function varies depending on
operating mode (1, 2)
MR2
MR3
RW
RW
RW
TCK0
RW
Count Source
Select Bit
Function varies depending on
operating mode
TCK1
RW
NOTES:
1. Only MR2 bits in the TB0MR and TB3MR registers are enabled.
2. Nothing is assigned in the MR2 bit in the TB1MR, TB2MR, TB4MR and TB5MR registers.
When write, set to "0". When read, its content is indeterminate.
Count Start Flag
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
TABSR
Bit
Symbol
Address
034016
After Reset
0016
Bit Name
Function
RW
TA0S
Timer A0 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA1S
Timer A1 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA2S
Timer A2 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA3S
Timer A3 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA4S
Timer A4 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB0S
Timer B0 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB1S
Timer B1 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB2S
Timer B2 Count
Start Flag
0: Stops counting
1: Starts counting
RW
Figure 14.18 TB0MR to TB5MR Registers, TABSR Register
Rev. 1.10 Oct. 18, 2005 Page 146 of 435
REJ09B0162-0110
14. Timer (Timer B)
M32C/88 Group (M32C/88T)
Timer B3, B4,B5 Count Start Flag
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset
TBSR
030016
000X XXXX2
Bit
Symbol
Bit Name
Function
RW
Nothing is assigned. When write, set to "0".
(b4 - b0) When read, its content is indeterminate.
TB3S
Timer B3 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB4S
Timer B4 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB5S
Timer B5 Count
Start Flag
0: Stops counting
1: Starts counting
RW
Figure 14.19 TBSR Register
Table 14.8 Settings for the TBiIN Pins (i=0 to 5)
Port Name
Function
Setting
PS1, PS3(1) Registers
PD7, PD9(1) Registers
P90
TB0IN
PS3_0=0
PD9_0=0
P91
TB1IN
PS3_1=0
PD9_1=0
P92
TB2IN
PS3_2=0
PD9_2=0
P93
TB3IN
PS3_3=0
PD9_3=0
P94
TB4IN
PS3_4=0
PD9_4=0
P71
TB5IN
PS1_1=0
PD7_1=0
NOTE:
1. Set the PD9 and PS3 registers immediately after the PRC2 bit in the PRCR register is set to
"1" (write enabled). Do not generate an interrupt or a DMA transfer between the instruction
to set the PRC2 bit to "1" and the instruction to set the PD9 and PS3 registers.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 147 of 435
14. Timer (Timer B)
M32C/88 Group (M32C/88T)
14.2.1 Timer Mode
In timer mode, the timer counts an internally generated count source (see Table 14.9). Figure 14.20
shows the TBiMR register (i=0 to 5) in timer mode.
Table 14.9 Timer Mode Specifications
Item
Specification
Count Source
f1, f8, f2n(1), fC32
Counting Operation
• The timer decrements a counter value
When the timer counter underflows, content of the reload register is reloaded into the
count register and counting resumes
Divide Ratio
1/(n+1)
n: setting value of the TBi register (i=0 to 5)
Counter Start Condition
The TBiS bits in the TABSR and TBSR registers are set to "1" (starts counting)
Counter Stop Condition
The TBiS bit is set to "0" (stops counting)
000016 to FFFF16
Interrupt Request Generation Timing Timer counter underflows
TBiIN Pin Function
Programmable I/O port
Read from Timer
The TBi register indicates counter value
Write to Timer
• When the timer counter stops, the value written to the TBi register is also written to
both reload register and counter
• While counting, the value written to the TBi register is written to the reload register
(It is transferred to the counter at the next reload timing)
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Timer Bi Mode Register (i=0 to 5) (Timer Mode)
b7
b6
b5
0
b4
b3
b2
b1
b0
0 0
Symbol
Address
After reset
TB0MR to TB5MR 035B16, 035C16, 035D16, 031B16, 031C16, 031D16 00XX 00002
Bit
Symbol
Bit Name
TMOD0
Operating Mode
Select Bit
Function
b1b0
MR1
RW
0 0: Timer mode
TMOD1
MR0
RW
RW
RW
Disabled in timer mode.
Can be set to "0" or "1".
RW
TB0MR, TB3MR registers:
Set to "0" in timer mode
MR2
TB1MR, TB2MR TB4MR, TB5MR registers:
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
MR3
Set to "0" in timer mode
RW
RW
b7 b6
TCK0
Count Source
Select Bit
TCK1
0 0: f1
0 1: f8
1 0: f2n(1)
1 1: fC32
RW
RW
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Figure 14.20 TB0MR to TB5MR Registers
Rev. 1.10 Oct. 18, 2005 Page 148 of 435
REJ09B0162-0110
14. Timer (Timer B)
M32C/88 Group (M32C/88T)
14.2.2 Event Counter Mode
In event counter mode, the timer counts how many external signals are applied or how many times
another timer overflows and underflows. (See Table 14.10) Figure 14.21 shows the TBiMR register (i=0
to 5) in event counter mode.
Table 14.10 Event Counter Mode Specifications
Item
Specification
• External signal applied to the TBiIN pin (i = 0 to 5) (valid edge can be selected by
Count Source
program)
• TBj overflow or underflow signal (j=i-1, except j=2 when i=0, j=5 when i=3)
Counting Operation
• The timer decrements a counter value
When the timer counter underflows, content of the reload register is reloaded into the
count register to continue counting
Divide Ratio
1/(n+1)
n : setting value of the TBi register
Counter Start Condition
The TBiS bits in the TABSR and TBSR register are set to "1" (starts counting)
Counter Stop Condition
The TBiS bit is set to "0" (stops counting)
000016 to FFFF16
Interrupt Request Generation Timing The timer counter underflows
TBiIN Pin Function
Programmable I/O port or count source input
Read from Timer
The TBi register indicates counter value
Write to Timer
• When the timer counter stops, the value written to the TBi register is also written to
both reload register and counter
• While counting, the value written to the TBi register is written to the reload register
(It is transferred to the counter at the next reload timing)
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 149 of 435
14. Timer (Timer B)
M32C/88 Group (M32C/88T)
Timer Bi Mode Register (i=0 to 5) (Event Counter Mode)
b7
b6
b5
0
b4
b3
b2
b1
b0
0 1
Symbol
Address
After reset
TB0MR to TB5MR 035B16, 035C16, 035D16, 031B16, 031C16, 031D16 00XX 00002
Bit
Symbol
TMOD0
TMOD1
Bit Name
Operating Mode
Select Bit
Function
b1b0
0 1: Event counter mode
RW
RW
RW
b3b2
MR0
Count Polarity Select
Bit(1)
MR1
0 0: Counts falling edges of external signal RW
0 1: Counts rising edges of external signal
1 0: Counts falling and rising edges of
external signal
RW
1 1: Do not set to this value
TB0MR and TB3MR registers:
Set to "0" in event counter mode
MR2
TB1MR, TB2MR, TB4MR and TB5MR registers:
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
MR3
Disabled in event counter mode. When write, set to "0".
When read, its content is indeterminate.
TCK0
Disabled in event counter mode.
Can be set to "0" or "1".
TCK1
RW
Event Clock
Select Bit
0: Input signal from the TBiIN pin
1: TBj overflows or underflows(2)
RW
RW
NOTES:
1. MR0 and MR1 bit settings are enabled when the TCK1 bit is set to "0". The MR1 bit can be set to
either "0" or "1", when the TCK1 bit is set to "1".
2. j=i-1, except j=2 when i=0 and j=5 when i=3.
Figure 14.21 TB0MR to TB5MR Registers
Rev. 1.10 Oct. 18, 2005 Page 150 of 435
REJ09B0162-0110
14. Timer (Timer B)
M32C/88 Group (M32C/88T)
14.2.3 Pulse Period/Pulse Width Measurement Mode
In pulse period/pulse width measurement mode, the timer measures pulse period or pulse width of an
external signal. (See Table 14.11) Figure 14.22 shows the TBiMR register (i=0 to 5) in pulse period/pulse
width measurement mode. Figure 14.23 shows an operation example in pulse period measurement
mode. Figure 14.24 shows an operation example in the pulse width measurement mode.
Table 14.11 Pulse Period/Pulse Width Measurement Mode Specifications
Item
Specification
Count Source
f1, f8, f2n(3), fC32
Counting Operation
• The timer increments a counter value
Counter value is transferred to the reload register on the valid edge of a pulse to be
measured. It is set to "000016" and the timer continues counting
Counter Start Condition
The TBiS bits (i=0 to 5) in the TABSR and TBSR register are set to "1" (starts counting)
Counter Stop Condition
The TBiS bit is set to "0" (stops counting)
Interrupt Request Generation Timing • On the valid edge of a pulse to be measured(1)
• The timer counter overflows
The MR3 bit in the TBiMR register is set to "1" (overflow) simultaneously. When the
TBiS bit is set to "1" (start counting) and the next count source is counted after setting
the MR3 bit to "1" (overflow), the MR3 bit can be set to "0" (no overflow) by writing to
the TBiMR register.
TBiIN Pin Function
Input for a pulse to be measured
Read from Timer
The TBi register indicates reload register values (measurement results)(2)
Write to Timer
Value written to the TBi register can be written to neither reload register nor counter
NOTES:
1. No interrupt request is generated when the pulse to be measured is on the first valid edge after the
timer has started counting.
2. The TBi register is in an indeterminate state until the pulse to be measured is on the second valid
edge after the timer has started counting.
3. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 151 of 435
14. Timer (Timer B)
M32C/88 Group (M32C/88T)
Timer Bi Mode Register (i=0 to 5)
(Pulse Period / Pulse Width Measurement Mode)
b7
b6
b5
b4
b3
b2
b1
b0
1 0
Symbol
Address
After reset
TB0MR to TB5MR 035B16, 035C16, 035D16, 031B16, 031C16, 031D16 00XX 00002
Bit
Symbol
TMOD0
TMOD1
Bit Name
Operating Mode
Select Bit
Function
RW
b1b0
RW
1 0: Pulse period measurement mode,
Pulse width measurement mode RW
b3b2
MR0
Measurement Mode
Select Bit(1)
MR1
0 0: Pulse period measurement 1
0 1: Pulse period measurement 2
1 0: Pulse width measurement
1 1: Do not set to this value
TB0MR, TB3MR registers:
Set to "0" in pulse period/pulse width measurement mode
MR2
MR3
RW
RW
RW
TB1MR, TB2MR TB4MR, TB5MR registers:
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
0: No overflow
Timer Bi Overflow Flag(2) 1: Overflow
RO
b7b6
TCK0
Count Source
Select Bit
TCK1
0 0: f1
0 1: f8
1 0: f2n(3)
1 1: fC32
RW
RW
NOTES:
1. The MR1 and MR0 bits selects the following measurements.
Pulse period measurement 1 (the MR1 and MR0 bits are set to "002") :
Measures between the falling edge and the next falling edge of a pulse to be measured
Pulse period measurement 2 (the MR1 and MR0 bits are set to "012") :
Measures between the rising edge and the next rising edge of a pulse to be measured
Pulse width measurement (the MR1 and MR0 bits are set to "102") :
Measures between a falling edge and the next rising edge of a pulse to be measured and
between the rising edge and the next falling edge of a pulse to be measured
2. The MR3 bit is indeterminate when reset.
To set the MR3 bit to "0", se the TBiMR register after the MR3 bit is set to "1" and one or more cycles
of the count source are counted, while the TBiS bits in the TABSR and TBSR registers are set to "1"
(starts counting).
The MR3 bit cannot be set to "1" by program.
3. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Figure 14.22 TB0MR to TB5MR Registers
Rev. 1.10 Oct. 18, 2005 Page 152 of 435
REJ09B0162-0110
14. Timer (Timer B)
M32C/88 Group (M32C/88T)
Count source
Pulse to be measured
"H"
"L"
Transferred
(indeterminate value)
Timing to transfer value
from counter to reload
register
Transferred
(measured value)
(Note 1)
(Note 1)
(Note 2)
Timing that the counter
reaches "000016"
TBiS bits in the TABSR "1"
and TBSR registers
"0"
"1"
IR bit in the TBilC
register
"0"
Set to "0" by an interrupt request acknowledgement or by program
MR3 bit in the TBiMR
register
"1"
"0"
i=0 to 5
NOTES:
1. The counter is reset when a measurement is completed.
2. The timer counter overflows.
Figure 14.23 Operation Example in Pulse Period Measurement Mode
Count source
"H"
Pulse to be measured
"L"
Timing to transfer value
from counter to reload
register
Transferred
(indeterminate
value)
(Note 1)
Transferred
(measured value)
(Note 1)
Transferred
(measured
value)
(Note 1)
Transferred
(measured value)
(Note 1)
(Note 2)
Timing that the counter
reaches "000016"
TBiS bits in the TABSR "1"
"0"
and TBSR registers
IR bit in the TBilC
register
"1"
"0"
Set to "0" by an interrupt request acknowledgement or by program
MR3 bit in the TBiMR
register
“1”
“0”
i=0 to 5
NOTES:
1. The counter is reset when a measurement is completed.
2. The timer counter overflows.
Figure 14.24 Operation Example in Pulse Width Measurement Mode
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 153 of 435
15. Three-Phase Motor Control Timer Functions
M32C/88 Group (M32C/88T)
15. Three-Phase Motor Control Timer Functions
Three-phase motor driving waveform can be output by using the timers A1, A2, A4 and B2. Table 15.1 lists
specifications of the three-phase motor control timer functions. Table 15.2 lists pin settings. Figure 15.1
shows a block diagram. Figures 15.2 to 15.7 show registers associated with the three-phase motor control
timer functions.
Table 15.1 Three-Phase Motor Control Timer Functions Specification
Item
Specification
___
___
___
Three-Phase Waveform Output Pin Six pins (U, U, V, V, W, W)
_______
Forced Cutoff(1)
Apply a low-level ("L") signal to the NMI pin
Timers to be Used
Timer A4, A1, A2 (used in one-shot timer mode):
___
Timer A4: U- and U-phase waveform control
___
Timer A1: V- and V-phase waveform control
___
Timer A2: W- and W-phase waveform control
Timer B2 (used in timer mode):
Carrier wave cycle control
Dead time timer (three 8-bit timers share reload register):
Dead time control
Output Waveform
Triangular wave modulation, Sawtooth wave modulation
Can output a high-level waveform or a low-level waveform for one cycle;
Can set positive-phase level and negative-phase level separately
Triangular wave modulation: count source x (m+1) x 2
Carrier Wave Cycle
Sawtooth wave modulation: count source x (m+1)
m: setting value of the TB2 register, 000016 to FFFF16
Count source: f1, f8, f2n(2), fc32
Three-Phase PWM Output Width
Triangular wave modulation: count source x n x 2
Sawtooth wave modulation: count source x n
n : setting value of the TA4, TA1 and TA2 register (of the TA4, TA41, TA1, TA11,
TA2 and TA21 registers when setting the INV11 bit to "1"), 000116 to FFFF16
Count source: f1, f8, f2n(2), fc32
Count source x p, or no dead time
Dead Time
p: setting value of the DTT register, 0116 to FF16
Count source: f1, or f1 divided by 2
Active Level
Selected from a high level ("H") or low level ("L")
Positive- and Negative-Phase Con- Positive and negative-phases concurrent active disable function
current Active Disable Function
Positive and negative-phases concurrent active detect function
Interrupt Frequency
For the timer B2 interrupt, one carrier wave cycle-to-cycle basis through 15
time- carrier wave cycle-to-cycle basis can be selected
NOTES:
_______
1. Forced cutoff by the signal applied to the NMI pin is available when the INV02 bit is set to "1" (threephase motor control timer functions) and the INV03 bit is set to "1" (three-phase motor control timer
output enabled).
2. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 154 of 435
15. Three-Phase Motor Control Timer Functions
M32C/88 Group (M32C/88T)
Table 15.2 Pin Settings
Setting
Pin
PS1, PS2 Registers(1)
PSL1, PSL2 Registers
PSC Register
P72/V
PS1_2 =1
PSL1_2 =0
PSC_2 =1
P73/V
PS1_3 =1
PSL1_3 =1
PSC_3 =0
P74/W
PS1_4 =1
PSL1_4 =1
PSC_4 =0
P75/W
PS1_5 =1
PSL1_5 =0
P80/U
PS2_0 =1
PSL2_0 =1
P81/U
PS2_1 =1
PSL2_1 =0
NOTE:
1. Set the PS1_5 to PS1_2 bits and PS2_1 and PS2_0 bits in the PS1 and PS2 registers to "1"
after the INV02 bit is set to "1".
Rev. 1.10 Oct. 18, 2005 Page 155 of 435
REJ09B0162-0110
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
(Timer Mode)
Timer B2
Page 156 of 435
TA41 Register
T Q
INV11
(One-shot Timer Mode)
Timer A4 Counter
Reload
TA11 Register
T Q
INV11
(One-shot Timer Mode)
Timer A1 Counter
Reload
Figure 15.1 Three-Phase Motor Control Timer Functions Block Diagram
TA21 Register
(One-shot Timer Mode)
INV11
T Q
Timer A2 Counter
Reload
When setting the TA2S bit to "0",
signal is set to "0"
Trigger
TA2 Register
When setting the TA1S bit to "0",
signal is set to "0"
Trigger
TA1 Register
When setting the TA4S bit to "0",
signal is set to "0"
Trigger
TA4 Register
INV07
INV00
Reload Control Signal for
the timer A4
Start Trigger Signal for
the timers A1, A2, A4
Write Signal
to Timer B2
INV10
Timer B2 Underflow
INV07 to INV00: Bits in INVC0 Register
INV15 to INV10: Bits in INVC1 Register
DUi, DUBi: Bits in IDBi Register (i=0,1)
TA4S to TA1S: Bits in TABSR Register
1/2
0
1
INV06
INV06
Timer A4
One-Shot
Pulse
Transfer
Trigger(1)
INV06
f1
INV12
INV01
INV11
0
1
T
Q
T
Q
T
Q
D
T
Q
DUB0
bit
D
DU0
bit
W-Phase Output Signal
W-Phase Output Signal
Dead Time Timer
n = 1 to 255
V-phase Output Signal
V-phase Output Signal
Dead Time Timer
n = 1 to 255
U-phase Output Signal
Three-phase Output
Shift Register
(U Phase)
U-Phase Output Signal
T
D Q
D Q
T
D Q
T
D Q
T
T
D Q
D Q
T
INV05
INV04
RESET
NMI
Value set to
the INV03 bit
Write signal to
the INV03 bit
R
Inverse
Control
Inverse
Control
Inverse
Control
Inverse
Control
Inverse
Control
Inverse
Control
INV14
INV02
T
D Q
INV03
Switching to P80, P81 and P72 to P75 is not shown in this diagram.
NOTE:
1. Transfer trigger is generated only when the IDB0 and IDB1 registers are set and the first timer B2 counter
underflows, if the INV06 bit is set to "0" (triangular wave modulation mode).
W-phase Output
Control Circuit
Trigger
Trigger
V-phase Output
Control Circuit
Trigger
Trigger
D
DUB1
bit
D
DU1
bit
Reload Register
n = 1 to 255
ICTB2 Counter
n=1 to 15
Timer B2
Interrupt Request Bit
ICTB2 Register n=1 to 15
Dead Time Timer
n = 1 to 255
U-phase Output
Control Circuit
Trigger
Trigger
A
PWCON
INV13
Circuit to set Interrupt
Generation Frequency
W
W
V
V
U
U
M32C/88 Group (M32C/88T)
15. Three-Phase Motor Control Timer Functions
15. Three-Phase Motor Control Timer Functions
M32C/88 Group (M32C/88T)
Three-Phase PWM Control Register 0(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
INVC0
030816
Bit
Symbol
After Reset
0016
Bit Name
Function
RW
INV00
Interrupt Enable Output
Polarity Select Bit(3)
0: The ICTB2 counter is incremented by one on the
rising edge of the timer A1 reload control signal
1: The ICTB2 counter is incremented by one on the
falling edge of the timer A1 reload control signal
RW
INV01
Interrupt Enable Output
Specification Bit(2, 3)
0: ICTB2 counter is incremented by one when
timer B2 counter underflows
1: Selected by the INV00 bit
RW
INV02 Mode Select Bit(4, 5, 6)
0: No three-phase control timer function
1: Three-phase control timer function
(6, 7)
INV03 Output Control Bit
0: Disables three-phase control timer output
1: Enables three-phase control timer output
RW
Positive and NegativeINV04 Phases Concurrent Active
Disable Function Enable Bit
Positive and NegativeINV05 Phases Concurrent Active
Output Detect Flag(8)
0: Enables concurrent active output
1: Disables concurrent active output
RW
0: Not detected
1: Detected
RW
Modulation Mode
Select(9, 10)
0: Triangular wave modulation mode
1: Sawtooth wave modulation mode
RW
Transfer trigger is generated when the
INV07 bit is set to "1". Trigger to the dead
time timer is also generated when setting the
INV06 bit to "1". Its value is "0" when read.
RW
INV06
INV07 Software Trigger Select
RW
NOTES:
1. Set the INVC0 register after the PRC1 bit in the PRCR register is set to "1" (write enabled).
Rewrite the INV02 to INV00 and INV06 bits when the timers A1,A2, A4 and B2 stop.
2. Set the INV01 bit to "1" after setting the ICTB2 register.
3. The INV01 and INV00 bit settings are enabled only when the INV11 bit in the INVC1 register is set to "1"
(three-phase mode 1). The ICTB2 counter is incremented by one every time the timer B2 counter
underflows, regardless of INV01 and INV00bit settings, when the INV11 bit is set to "0" (three-phase mode).
When setting the INV01 bit to "1", set the timer A1 count start flag before the first timer B2 counter underflows.
When the INV00 bit is set to "1", the first interrupt is generated when the timer B2 counter underflows n-1
times, if n is the value set in the ICTB2 counter. Subsequent interrupts are generated every n times the
timer B2 counter underflows.
4. Set the INV02 bit to "1" to operate the dead time timer, U-, V-and W-phase output control circuits and ICTB2
counter.
5. Set pins after the INV02 bit is set to "1". See Table 16.2 for pin settings.
6. When the INV02 bit is set to "1" and the INV03 bit to "0", the U, U, V, V, W and W pins, including pins
shared with other output functions, are all placed in high-impedance states.
7. The INV03 bit is set to "0" when the followings occurs :
- Reset
- A concurrent active state occurs while the INV04 bit is set to "1"
- The INV03 bit is set to "0" by program
- An "H" signal applied to the NMI pin changes to an "L" signal
8. The INV05 bit can not be set to "1" by program. Set the INV04 bit to "0", as well, when setting the INV05 bit
to "0".
9. The following table describes how the INV06 bit setting works.
Item
Mode
Timing to Transfer from the IDB0
and IDB1 Registers to ThreePhase Output Shift Register
INV06 = 0
Triangular wave modulation mode
Transferred once by generating a
transfer trigger after setting the IDB0
and IDB1 registers
INV06 = 1
Sawtooth wave modulation mode
Transferred every time a transfer trigger
is generated
Timing to Trigger the Dead Time On the falling edge of a one-shot pulse By a transfer trigger, or the falling edge of
Timer when the INV16 Bit=0
a one-shot pulse of the timer A1, A2 or A4
of the timer A1, A2 or A4
INV13 Bit
Enabled when the INV11 bit=1 and the Disabled
INV06 bit=0
Transfer trigger : Timer B2 counter underflows and write to the INV07 bit, or write to the TB2 register when INV10 = 1
10. When the INV06 bit is set to "1", set the INV11 bit to "0" (three-phase mode 0) and the PWCON bit in the
TB2SC register to "0" (timer B2 counter underflows).
Figure 15.2 INVC0 Register
Rev. 1.10 Oct. 18, 2005 Page 157 of 435
REJ09B0162-0110
15. Three-Phase Motor Control Timer Functions
M32C/88 Group (M32C/88T)
Three-Phase PWM Control Register 1(1)
b7
b6
b5
b4
b3
b2
b1
b0
0
Symbol
INVC1
Bit
Symbol
Address
030916
After Reset
0016
Bit Name
Function
RW
INV10
Timer A1, A2 and A4
Start Trigger Select Bit
0: Timer B2 counter underflows
1: Timer B2 counter underflows and
write to the TB2 register
INV11
Timer A1-1, A2-1 and
A4-1 Control Bit(2, 3)
0: Three-phase mode 0
1: Three-phase mode 1
INV12
Dead Time Timer
0: f1
Count Source Select Bit 1: f1 divided-by-2
INV13
Carrier Wave Detect Flag(4)
0: Timer A1 reload control signal is "0"
RO
1: Timer A1 reload control signal is "1"
INV14
Output Polarity Control Bit
0: Active "L" of an output waveform
1: Active "H" of an output waveform
RW
INV15
Dead Time Disable Bit
0: Enables dead time
1: Disables dead time
RW
INV16
0: Falling edge of a one-shot pulse of
Dead Time Timer Trigger the timer A1, A2 and A4(5)
RW
1: Rising edge of the three-phase output
Select Bit
shift register (U-, V-, W-phase)
Reserved Bit
RW
RW
RW
Set to "0"
RW
(b7)
NOTES:
1. Rewrite the INVC1 register after the PRC1 bit in the PRCR register is set to "1" (write enabled).
The timers A1, A2, A4, and B2 must be stopped during rewrite.
2. The following table lists how the INV11 bit setting works.
Item
INV11 = 0
Mode
Three-phase mode 0
TA11, TA21 and TA41 Registers Not used
INV11 = 1
Three-phase mode 1
Used
INV01 and INV00 Bit
in the INVC0 Register
Disabled. The ICTB2 counter is
incremented whenever the timer B2
counter underflows
Enabled
INV13 Bit
Disabled
Enabled when INV11=1 and INV06=0
3. When the INV06 bit in the INVC0 registser is set to "1" (sawtooth wave modulation mode), set the
INV11 bit to "0". Also, when the INV11 bit is set to "0", set the PWCON bit in the TB2SC register to
"0" (Timer B2 counter underflows).
4. The INV13 bit setting is enabled only when the INV06 bit is set to "0" (Triangular wave modulation
mode) and the INV11 bit to "1".
5. If the following conditions are all met, set the INV16 bit to "1".
• The INV15 bit is set to "0"
• The Dij bit (i=U, V or W, j=0, 1) and DiBj bit always have different values when the INV03 bit in
the INVC0 register is set to "1". (The positive-phase and negative-phase outputs always provide
opposite level signals.)
If the above conditions are not met, set the INV16 bit to "0".
Figure 15.3 INVC1 Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 158 of 435
15. Three-Phase Motor Control Timer Functions
M32C/88 Group (M32C/88T)
Three-Phase Output Buffer Register i(1) (i=0, 1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset
IDB0, IDB1
030A16, 030B16
XX11 11112
Bit
Symbol
DUi
DUBi
DVi
DVBi
DWi
DWBi
Bit Name
Function
RW
U-Phase Output Buffer i Write output level
U-Phase Output Buffer i 0: Active level
1: Inactive level
V-Phase Output Buffer i
RW
V-Phase Output Buffer i
When read, the value of the threeW-Phase Output Buffer i phase shift register is read.
RW
W-Phase Output Buffer i
RW
Reserved Bit
(b7 - b6)
RW
RW
When read,
its content is indeterminate
RW
RO
NOTE:
1. Values of the IDB0 and IDB1 registers are transferred to the three-phase output shift register by a
transfer trigger.
After the transfer trigger occurs, the values written in the IDB0 register determine each phase output
signal level first. Then the value written in the IDB1 register on the falling edge of the timers A1, A2
and A4 one-shot pulse determines each phase output signal level.
Dead Time Timer(1, 2)
b7
b0
Symbol
DTT
Address
030C16
Function
If setting value is n, the timer stops when counting
n times a count source selected by the INV12 bit
after start trigger occurs. Positive or negative
phase, which changes from inactive level to active
level, shifts when the dead time timer stops.
After Reset
Indeterminate
Setting Range
RW
1 to 255
WO
NOTES:
1. Use the MOV instruction to set the DTT register.
2. The DTT register setting is enabled when the INV15 bit in the INVC1 register is set to "0" (dead time
enabled). No dead time can be set when the INV15 bit is set to "1" (dead time disabled). The INV06
bit in the INVC0 register determines start trigger of the DTT register.
Figure 15.4 IDB0 and IDB1 registers, DTT Register
Rev. 1.10 Oct. 18, 2005 Page 159 of 435
REJ09B0162-0110
15. Three-Phase Motor Control Timer Functions
M32C/88 Group (M32C/88T)
Timer B2 Interrupt Generation Frequency Set Counter(1, 2, 3)
b7
b0
Symbol
Address
After Reset
ICTB2
030D16
Indeterminate
Setting Range
Function
When the INV01 bit is set to "0" (the ICTB2 counter
increments whenever the timer B2 counter underflows) and
the setting value is n, the timer B2 interrupt is generated
every nth time timer B2 counter underflow occurs.
When the INV01 bit is set to "1" (the INV00 bit selects
count timing of the ICTB2 counter) and setting value is
n, the timer B2 interrupt is generated every nth time
timer B2 counter underflow meeting the condition
selected in the INV00 bit occurs.
1 to 15
RW
WO
Nothing is assigned. When write, set to "0".
NOTES:
1. Use the MOV instruction to set the ICTB2 register.
2. If the INV01 bit in the INVC0 register is set to "1", set the ICTB2 register in the TABSR register when
the TB2S bit is set to "0" (timer B2 counter stopped).
If the INV01 bit is set to "0" and the TB2S bit to "1" (timer B2 counter start), do not set the ICTB2
register when the timer B2 counter underflows.
3. If the INV00 bit in the INVC0 register is set to "1", the first interrupt is generated when the timer B2
counter underflows n-1 times, n being the value set in the ICTB2 counter. Subsequent interrupts are
generated every n times the timer B2 counter underflows.
Timer Ai, Ai-1 Register (i=1, 2, 4)(1, 2, 3, 4, 5, 6)
b15
b8 b7
Symbol
TA1, TA2, TA4
b0
TA11, TA21, TA41
Address
After Reset
034916 - 034816, 034B16 - 034A16, 034F16 - 034E16 Indeterminate
030316 - 030216, 030516 - 030416, 030716 - 030616 Indeterminate
Function
If setting value is n, the timer stops when the nth count
source is counted after a start trigger is generated.
Positive phase changes to negative phase, and vice
versa, when the timers A1, A2 and A4 stop.
Setting Range
RW
000016 to FFFF16
WO
NOTES:
1. Use a 16-bit data for read and write.
2. If the TAi or TAi1 register is set to "000016", no counter starts and no timer Ai interrupt is generated.
3. Use the MOV instruction to set the TAi and TAi1 registers.
4. When the INV15 bit in the INVC1 register is set to "0" (dead timer enabled), phase switches from an
inactive level to an active level when the dead time timer stops.
5. When the INV11 bit in the INVC1 register is set to "0" (three-phase mode 0), the value of the TAi
register is transferred to the reload register by a timer Ai start trigger.
When the INV11 bit is set to "1" (three-phase mode 1), the value of the TAi1 register is first transferred
to the reload register by a timer Ai start trigger. Then, the value of the TAi register is transferred by the
next trigger. The values of the TAi1 and TAi registers are transferred alternately to the reload register
with every timer Ai start trigger.
6. Do not write to these registers when the timer B2 counter underflows.
Timer B2 Special Mode Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset
TB2SC
035E16
XXXX XXX02
Bit
Symbol
PWCON
Bit Name
Timer B2 Reload Timing
Switching Bit(1)
Function
0: Timer B2 counter underflows
1: Timer A output in odd-number
times
RW
RW
Nothing is assigned. When write, set to "0".
When read, its content is "0."
NOTE:
1. Set the PWCON bit to "0" when setting the INV11 bit to "0" (three-phase mode 0) or the INV06 bit to
"1" (sawtooth wave modulation mode).
Figure 15.5 ICTB2 Register, TA1, TA2, TA4, TA11, TA21, and TA41 Registers, TB2SC Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 160 of 435
15. Three-Phase Motor Control Timer Functions
M32C/88 Group (M32C/88T)
Timer B2 Register(1)
b15
b8 b7
b0
Symbol
Address
After Reset
TB2
035516 - 035416
Indeterminate
Setting Range
Function
If setting value is n, count source is divided by n+1.
000016 to FFFF16
The timers A1, A2, and A4 start every time an underflow occurs.
RW
RW
NOTE:
1. Use a 16-bit data for read and write.
Trigger Select Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset
TRGSR
034316
0016
Bit
Symbol
TA1TGL
TA1TGH
TA2TGL
TA2TGH
Bit Name
Function
RW
Timer A1 Event/Trigger
Select Bit
Set to "012" (TB2 underflow) before
using a V-phase output control circuit
RW
Timer A2 Event/Trigger
Select Bit
Set to "012" (TB2 underflow) before
using a W-phase output control circuit
RW
RW
RW
b5b4
Timer A3 Event/Trigger
Select Bit
0 0: Selects an input to the TA3IN pin RW
0 1: Selects TB2 overflow(1)
1 0: Selects TA2 overflow(1)
RW
1 1: Selects TA4 overflow(1)
Timer A4 Event/Trigger
Select Bit
Set to "012" (TB2 underflow) before
using a U-phase output control circuit
TA3TGL
TA3TGH
TA4TGL
TA4TGH
RW
RW
NOTE:
1. Overflow or underflow.
Count Start Flag
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset
TABSR
034016
0016
Bit
Symbol
Bit Name
Function
RW
TA0S
Timer A0 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA1S
Timer A1 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA2S
Timer A2 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA3S
Timer A3 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TA4S
Timer A4 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB0S
Timer B0 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB1S
Timer B1 Count
Start Flag
0: Stops counting
1: Starts counting
RW
TB2S
Timer B2 Count
Start Flag
0: Stops counting
1: Starts counting
RW
Figure 15.6 TB2, TRGSR, and TABSR Registers
Rev. 1.10 Oct. 18, 2005 Page 161 of 435
REJ09B0162-0110
15. Three-Phase Motor Control Timer Functions
M32C/88 Group (M32C/88T)
Timer Ai Mode Register (i=1, 2, 4)
b7
b6
b5
b4
b2
b1
b0
Symbol
Address
After Reset
0
1 0 0
1
0
TA1MR, TA2MR, TA4MR
035716, 035816, 035A16
0016
b3
Bit
Symbol
Bit Name
TMOD0 Operating Mode
TMOD1 Select Bit
Function
RW
Set to "102" (one-shot timer
mode) when using the three-phase
motor control timer function
RW
RW
MR0
Reserved Bit
Set to "0"
MR1
External Trigger Select
Bit
Set to "0" when using the three-phase RW
motor control timer function
MR2
Trigger Select Bit
Set to "1" (selected by the TRGSR
register) when using the threephase motor control timer function
MR3
Set to "0" with the three-phase motor control timer function
TCK0
0 0: f1
Count Source Select Bit 0 1: f8
1 0: f2n(1)
1 1: fC32
RW
RW
b7 b6
TCK1
RW
RW
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Timer B2 Mode Register
b7
b6
b5
b4
b3
b2
b1
b0
0 0 0 0 0
Symbol
Address
After Reset
TB2MR
035D16
00XX 00002
Bit
Symbol
Bit Name
Function
RW
MR1
Set to "002" (timer mode) when using
Operating Mode
RW
the three-phase motor control timer
Select Bit
function
Disabled when using the three-phase motor control timer function.
When write, set to "0".
When read, its content is indeterminate.
MR2
Set to "0" when using three-phase motor control timer function RW
MR3
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
TMOD0
TMOD1
MR0
RW
b7 b6
TCK0
Count Source Select Bit
TCK1
0 0: f1
0 1: f8
1 0: f2n(1)
1 1: fC32
RW
RW
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Figure 15.7 TA1MR, TA2MR, and TA4MR Registers, TB2MR Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 162 of 435
15. Three-Phase Motor Control Timer Functions
M32C/88 Group (M32C/88T)
The three-phase motor control timer function is available by setting the INV02 bit in the INVC0 register to
"1". The timer B2 is used for carrier wave control and the timers A1, A2, A4 for three-phase PWM output
__
__
___
(U, U, V, V, W, W) control. An exclusive dead time timer controls dead time. Figure 15.8 shows an
example of the triangular modulation waveform. Figure 15.9 shows an example of the sawtooth modulation waveform.
Triangular waveform as a Carrier Wave
Triangular Wave
Signal Wave
TB2S Bit in
TABSR Register
Timer B2
Timer A1
Reload Control Signal(1)
Timer A4
Start Trigger Signal(1)
TA4 Register(2)
m
n
p
q
r
TA4-1 Register(2)
m
n
p
q
r
Reload
Register(2)
m
Timer A4
One-Shot Pulse(1)
m
m
n
m
n
n
n
p
p
n
q
q
p
p
q
r
q
Rewrite the IDB0 and IDB1 registers
U-Phase
Output Signal(1)
Transfer the values
to the three-phase
shift register
U-Phase
Output Signal(1)
U-Phase
INV14 = 0
("L" active)
U-Phase
Dead time
INV14 = 1
("H" active)
U-Phase
Dead time
U-Phase
INV00, INV01: Bits in INVC0 register
INV11, INV14: Bits in INVC1 register
NOTES:
1. Internal signals. See Figure 15.1.
2. Applies only when the INV11 bit is set to "1" (three-phase mode).
The above applies to INVC0 = 00XX11XX2 and INVC1 = 010XXXX02 (X varies depending on individual system.)
Examples of PWM output change are
(b) When INV11=0 (three-phase mode 0)
(a) When INV11=1 (three-phase mode 1)
- INV01=0, ICTB2=116 (The timer B2 interrupt is generated
- INV01=0 and ICTB2=216 (The timer B2 interrupt is
whenever the timer B2 underflows)
generated with every second timer B2 underflow) or
- Default value of the timer: TA4=m
INV01=1, INV00=1and ICTB2=116 (The timer B2 interrupt is
The TA4 register is changed whenever the timer B2
generated on the falling edge of the timer A reload control
interrupt is generated.
signal)
First time: TA4=m. Second time: TA4=n.
- Default value of the timer: TA41=m, TA4=m
Third time: TA4=n. Fourth time: TA=p.
The TA4 and TA41 registers are changed whenever the
Fifth time: TA4=p.
timer B2 interrupt is generated.
- Default value of the IDB0 and IDB1 registers:
First time: TA41=n, TA4:=n.
DU0=1, DUB0=0, DU1=0, DUB1=1
Second time: TA41=p, TA4=p.
They are changed to DU0=1, DUB0=0, DU1=1, DUB1=0 by
- Default value of the IDB0 and IDB1 registers
the sixth timer B2 interrupt.
DU0=1, DUB0=0, DU1=0, DUB1=1
They are changed to DU0=1, DUB0=0, DU1=1, DUB1=0
by the third timer B2 interrupt.
Figure 15.8 Triangular Wave Modulation Operation
Rev. 1.10 Oct. 18, 2005 Page 163 of 435
REJ09B0162-0110
15. Three-Phase Motor Control Timer Functions
M32C/88 Group (M32C/88T)
Sawtooth Waveform as a Carrier Wave
Sawtooth Wave
Signal Wave
Timer B2
Timer A4 Start
Trigger Signal(1)
Timer A4
One-Shot Pulse(1)
Rewrite the IDB0 and IDB1 registers
Transfer the register values to
the three-phase shift register
U-Phase
(1)
Output Signal
U-Phase
(1)
Output Signal
U-Phase
INV14 = 0
("L" active)
Dead time
U-Phase
U-Phase
INV14 = 1
("H" active)
Dead time
U-Phase
INV14: Bits in INVC1 register
NOTE:
1. Internal signals. See Figure 15.1.
The above applies to INVC0 = 01XX110X2 and INVC1 = 000XXX002 (X varies depending on individual system.)
The examples of PWM output change are
- Default value of the IDB0 and IDB1 registers: DU0=0, DUB0=1, DU1=1, DUB1=1
They are changed to DU0=1, DUB0=0, DU1=1, DUB1=1 by the timer B2 interrupt.
Figure 15.9 Sawtooth Wave Modulation Operation
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 164 of 435
M32C/88 Group (M32C/88T)
16. Serial I/O
16. Serial I/O
Serial I/O consists of five channels (UART0 to UART4).
Each UARTi (i=0 to 4) has an exclusive timer to generate the transfer clock and operates independently.
Figure 16.1 shows a UARTi block diagram.
UARTi supports the following modes :
- Clock synchronous serial I/O mode
- Clock asynchronous serial I/O mode (UART mode)
- Special mode 1 (I2C mode)
- Special mode 2
- Special mode 3 (Clock-divided synchronous function, GCI mode)
- Special mode 4 (Bus conflict detect function, IE mode)
- Special mode 5 (SIM mode)
Figures 16.2 to 16.9 show registers associated with UARTi.
Refer to the tables listing each mode for register and pin settings.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 165 of 435
16. Serial I/O
M32C/88 Group (M32C/88T)
RxD Polarity
Switching Circuit
RxDi
Selecting Clock Source
00
CKDIR
f1
Internal
01
0
f8
10
f2n(2)
CLK1 and 1
CLK0
External
Clock Asynchronous
Receive
SMD2 to SMD0
010, 100, 101, 110
1/16
Receive
001
Control Circuit
Clock Synchronous
UiBRG
Register
Receive
Clock
Clock Asynchronous
Transmit
1 / (m+1)
1/16
Transmit/
Receive
Unit
TxDi
(Note 1)
Transmit
Clock
Transmit
Control Circuit
010, 100, 101, 110
Clock Synchronous
001
Clock Synchronous (when
internal clock is selected)
TxD
Polarity
Switching
Circuit
1/2
0
1
Clock
Synchronous
Clock Synchronous
CKDIR
(when internal clock is selected) (when external clock is
selected)
CKPOL
CLKi
CLK
Polarity
Switching
Circuit
CTS/RTS
selected
1
CTSi / RTSi
CTS/RTS disabled
CRD
RTSi
CRS 0
0
1
CRD CTS/RTS disabled
CTSi
m: setting value of the UiBRG register
VSS
IOPOL
No inverse
0
RxD Data
Inverse Circuit
RxDi
NOTES:
1. P70 and P71 are ports for the N-channel open drain output, but
not for the CMOS output.
2. The CNT3 to CNT0 bits in the TCSPR register select no division
(n=0) or divide-by-2n (n=1 to 15).
1
Inverse
Clock
Synchronous
7-bit Clock
Asynchronous
8-bit Clock
Asynchronous
PRYE
PAR
Clock
disabled Synchronous
0
STPS
1SP
0
SP
SP
7-bit Clock
Asynchronous
UARTi Receive Register
0
0
PAR
Clock
1
Asynchronous
PAR
enabled SMD2 to SMD0
1
2SP
1
9-bit Clock
Asynchronous
Type
Clock 1
Synchronous
8-bit Clock
Asynchronous
9-bit Clock
Asynchronous
0
0
0
0
0
0
0
D8
D7
D6
D5
D4
D3
D2
D1
D0
UiRB Register
Logic Inverse Circuit + MSB/LSB Conversion Circuit
High-order bits of data bus
Low-order bits of data bus
Logic Inverse Circuit + MSB/LSB Conversion Circuit
D8
STPS
2SP
1
SP
SP
PRYE
SMD2 to SMD0
PAR
enabled
1
Clock
Asynchronous
1
9-bit Clock
Asynchronous
1
D7
D6
D5
D4
D3
D2
D1
D0
UiTB Register
8-bit Clock
Asynchronous
9-bit Clock
Asynchronous
Clock
Synchronous
1
PAR
0
1SP
0
Clock
PAR
Synchronous
disabled
0
0
7-bit Clock
Asynchronous
8-bit Clock
Asynchronous
Clock
Synchronous
0 7-bit Clock
Asynchronous
UARTi Transmit Register
Error Signal Output
disabled
0
SP: Stop bit
PAR: Parity bit
i=0 to 4
SMD2 to SMD0, STPS, PRYE, IOPOL, CKDIR: Bits in the UiMR register
CLK1 and CLK0, CKPOL, CRD, CRS: Bits in the UiC0 register
UiERE: Bit in the UiC1 register
Figure 16.1 UARTi Block Diagram
Rev. 1.10 Oct. 18, 2005 Page 166 of 435
REJ09B0162-0110
Error Signal
Output Circuit
1
Error Signal Output
enabled
UiERE
IOPOL
0
1
Inverse
No inverse
TxD Data
Inverse Circuit
TxDi
16. Serial I/O
M32C/88 Group (M32C/88T)
UARTi Transmit Buffer Register (i=0 to 4)(1)
b15
b8 b7
b0
Symbol
Address
U0TB to U2TB 036B16-036A16, 02EB16-02EA16, 033B16-033A16
U3TB, U4TB
032B16-032A16, 02FB16-02FA16
Bit
Symbol
After Reset
Indeterminate
Indeterminate
RW
Function
(b7 - b0) Transmit data (D7 to D0)
(b8)
WO
Transmit data (D8)
WO
Nothing is assigned.
When write, set to "0".
(b15 - b9) When read, its content is indeterminate.
NOTE:
1. Use the MOV instruction to set the UiTB register.
UARTi Receive Buffer Register (i=0 to 4)
b15
b8 b7
b0
Symbol
Address
U0RB to U2RB 036F16 - 036E16, 02EF16 - 02EE16, 033F16 - 033E16
U3RB, U4RB
032F16 - 032E16, 02FF16 - 02FE16
Bit
Symbol
Bit Name
Function
Indeterminate
Indeterminate
RW
Received data (D7 to D0)
RO
Received data (D8)
RO
(b7 - b0)
(b8)
After Reset
Nothing is assigned. When write, set to "0".
(b10 - b9) When read, its content is indeterminate.
ABT
Arbitration Lost
Detect Flag(1)
OER
0: No overrun error occurs
Overrun Error Flag(2) 1: Overrun error occurs
RO
FER
Framing Error
Flag(2, 3)
0: No framing error occurs
1: Framing error occurs
RO
PER
Parity Error Flag(2, 3)
0: No parity error occurs
1: Parity error occurs
RO
SUM
Error Sum Flag(2, 3)
0: No error occurs
1: Error occurs
RO
0: Not detected (win)
1: Detected (lose)
RW
NOTES:
1. The ABT bit can be set to "0" only.
2. When the SMD2 to SMD0 bits in the UiMR register are set to "0002" (serial I/O disable) or the RE bit in
the UiC1 register is set to "0" (receive disable), the OER, FER, PER and SUM bits are set to "0".
When all OER, FER and PER bits are set to "0", the SUM bit is set to "0".
Also, the FER and PER bits are set to "0" by reading low-order bits in the UiRB register.
3. These error flags are disabled when the SMD2 to SMD0 bits are set to "0012" (clock synchronous serial
I/O mode) or to "0102" (I2C mode). When read, the contents are indeterminate.
Figure 16.2 U0TB to U4TB Registers and U0RB to U4RB Registers
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 167 of 435
16. Serial I/O
M32C/88 Group (M32C/88T)
UARTi Bit Rate Register (i=0 to 4)(1, 2, 3)
b7
b0
Symbol
Address
U0BRG to U4BRG 036916, 02E916, 033916, 032916, 02F916
Function
After Reset
Indeterminate
Setting Range
If the setting value is m, the UiBRG register
divides a count source by m+1
0016 to FF16
RW
WO
NOTES:
1. Use the MOV instruction to set the UiBRG register.
2. Set the UiBRG register while no data transfer occurs.
3. Set the CLK1 and CLK0 bits in the UiC0 register, and then the UiBRG register.
UARTi Transmit/Receive Mode Register (i=0 to 4)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
U0MR to U4MR
Bit
Symbol
Address
036816, 02E816, 033816, 032816, 02F816
Bit Name
Function
After Reset
0016
RW
b2 b1 b0
SMD0
SMD1
SMD2
0 0 0: Serial I/O disabled
RW
0 0 1: Clock synchronous serial I/O mode
2
Serial I/O Mode Select 0 1 0: I C mode
RW
1 0 0: UART mode, 7-bit transfer data
Bit
1 0 1: UART mode, 8-bit transfer data
1 1 0: UART mode, 9-bit transfer data
RW
Do not set value other than the above
CKDIR
Internal/External Clock 0: Internal clock
Select Bit
1: External clock
RW
STPS
Stop Bit Length Select 0: 1 stop bit
Bit
1: 2 stop bits
RW
PRY
Odd/Even Parity Select Enables when PRYE = 1
0: Odd parity
Bit
1: Even parity
RW
0: Disables a parity
1: Enables a parity
PRYE
Parity Enable Bit
IOPOL
TxD,RxD Input/Output 0: Not inversed
Polarity Switch Bit
1: Inverse
Figure 16.3 U0BRG to U4BRG Registers and U0MR to U4MR Registers
Rev. 1.10 Oct. 18, 2005 Page 168 of 435
REJ09B0162-0110
RW
RW
16. Serial I/O
M32C/88 Group (M32C/88T)
UARTi Transmit/Receive Control Register 0 (i=0 to 4)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
U0C0 to U4C0
Bit
Symbol
Address
036C16, 02EC16, 033C16, 032C16, 02FC16
Bit Name
After Reset
0000 10002
Function
RW
b1 b0
CLK0
CLK1
CRS
0 0: Selects f1
UiBRG Count
0 1: Selects f8
(4)
Source Select Bit
1 0: Selects f2n(2)
1 1: Do not set to this value
CST/RTS Function Enabled when CRD=0
0: Selects CTS function
Select Bit
1: Selects RTS function
RW
RW
RW
TXEPT
Transmit Register
Empty Flag
0: Data in the transmit register
(during transmission)
1: No data in the transmit register
(transmission is completed)
RO
CRD
CTS/RTS Disable
Bit
0: Enables CTS/RTS function
1: Disables CTS/RTS function
RW
0: TxDi/SDAi and SCLi are ports for the
Data Output Select
CMOS output
NCH
RW
Bit(1)
1: TxDi/SDAi and SCLi are ports for the
N-channel open drain output
0: Data is transmitted on the falling edge of
the transfer clock and data is received
on the rising edge
CLK Polarity
CKPOL
RW
1: Data is transmitted on the rising edge of
Select Bit
the transfer clock and data is received
on the falling edge
UFORM
Transfer Format
Select Bit(3)
0: LSB first
1: MSB first
RW
NOTES:
1. P70/TxD2 and P71/SCL2 are ports for the N-channel open drain output, but not for the CMOS output.
2. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
3. The UFORM bit setting is enabled when the SMD2 to SMD0 bits in the UiMR register are set to
"0012" (clock syncronous serial I/O mode) or "1012" (UART mode, 8-bit transfer data).
Set the UFORM bit to "1" when setting the SMD2 to SMD0 bits to"0102" (I2C mode), or to "0" when
setting them to "1002" (UART mode, 7-bit transfer data) or "1102" (UART mode, 9-bit transfer data).
4. Set the UiBRG register after the CLK1 and CLK0 bit settings are changed.
Figure 16.4 U0C0 to U4C0 Registers
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 169 of 435
16. Serial I/O
M32C/88 Group (M32C/88T)
UARTi Transmit/Receive Control Register 1 (i=0 to 4)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
U0C1 to U4C1
Bit
Symbol
Address
036D16, 02ED16, 033D16, 032D16, 02FD16
After Reset
0000 00102
Function
Bit Name
RW
0: Transmit disabled
1: Transmit enabled
TE
Transmit
Enable Bit
TI
Transmit Buffer 0: Data in the UiTB register
1: No data in the UiTB register
Empty Flag
RE
Receive
Enable Bit
0: Receive disabled
1: Receive enabled
RW
RI
Receive
Complete Flag
0: No data in the UiRB register
1: Data in the UiRB register
RO
UiIRS
RW
RO
UARTi Transmit 0: No data in the UiTB register (TI = 1)
Interrupt Cause
1: Transmission is completed (TXEPT = 1)
Select Bit
RW
UiRRM
UARTi
Continuous
Receive Mode
Enable Bit
0: Disables continuous receive mode to be entered
RW
1: Enables continuous receive mode to be entered
UiLCH
Data Logic
Select Bit(2)
0: Not inversed
1: Inverse
Clock-Divided
Synchronous Stop
SCLKSTPB Bit /
/UiERE
Error Signal
Output Enable
Bit(1)
RW
Clock-divided synchronous stop bit (special mode 3)
0: Stops synchronizing
1: Starts synchronizing
RW
Error signal output enable bit (special mode 5)
0: Not output
1: Output
NOTES:
1. Set the SCLKSTPB/UiERE bit after setting the SMD2 to SMD0 bits in the UiMR register.
2. The UiLCH bit setting is enabled when setting the SMD2 to SMD0 bits to "0012" (clock syncronous
serial I/O mode), "1002" (UART mode, 7-bit transfer data) or "1012" (UART mode, 8-bit transfer data).
Set the UiLCH bit to "0" when setting the SMD2 to SMD0 bits to"0102" (I2C mode) or "1102" (UART
mode, 9-bit transfer data).
UARTi Special Mode Register (i=0 to 4)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
U0SMR to U4SMR
Bit
Symbol
Address
036716, 02E716, 033716, 032716, 02F716
After Reset
0016
Function
Bit Name
0: Except I2C mode
1: I2C mode
IICM
I2C Mode Select Bit
ABC
Arbitration Lost Detect 0: Update per bit
Flag Control Bit
1: Update per byte
BBS
Bus Busy Flag
0: Stop condition detected
1: Start condition detected (Busy)
SCLL Sync Output
Enable Bit
0: Disabled
1: Enabled
LSYN
ABSCS
ACSE
SSS
SCLKDIV
RW
RW
RW(1)
RW
Bus Conflict Detect
0: Rising edge of transfer clock
Sampling Clock Select Bit 1: Timer Aj underflow(j=0 to 4)(2)
RW
Auto Clear Function Select 0: No auto clear function
Bit for Transmit Enable Bit 1: Auto clear at bus conflict
RW
Transmit Start
Condition Select Bit
0: Not related to RxDi
1: Synchronized with RxDi
RW
Clock Divide
Synchronous Bit
(Note 3)
RW
NOTES:
1. The BBS bit is set to "0" by program. It is unchanged if set to "1".
2. UART0: timer A3 underflow signal, UART1: timer A4 underflow signal,
UART2: timer A0 underflow signal, UART3: timer A3 underflow signal,
UART4: timer A4 underflow signal.
3. Refer to notes for the SU1HIM bit in the UiSMR2 register.
Figure 16.5 U0C1 to U4C1 Registers and U0SMR to U4SMR Registers
Rev. 1.10 Oct. 18, 2005 Page 170 of 435
REJ09B0162-0110
RW
16. Serial I/O
M32C/88 Group (M32C/88T)
UARTi Special Mode Register 2 (i=0 to 4)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
U0SMR2 to U4SMR2
Address
036616, 02E616, 033616, 032616, 02F616
After Reset
0016
Bit
Symbol
Bit Name
IICM2
I2C Mode Select Bit 2
(Note 1)
RW
CSC
Clock Synchronous Bit
0: Disabled
1: Enabled
RW
SWC
SCL Wait Output Bit
0: Disabled
1: Enabled
RW
ALS
SDA Output Stop Bit
0: Output
1: No output
RW
STC
UARTi Initialize Bit
0: Disabled
1: Enabled
RW
SWC2
SCL Wait Output Bit 2
0: Transfer clock
1: "L" output
RW
SDHI
SDA Output Inhibit Bit
0: Output
1: No output (high-impedance)
RW
External Clock
Synchronous Enable Bit
(Note 2)
RW
SU1HIM
Function
NOTES:
1. Refer to Table 16.14.
2. The external clock synchronous function can be selected by combining the SU1HIM bit and the
SCLKDIV bit in the UiSMR register.
SCLKDIV bit in the
UiSMR Register
SU1HIM bit in the
UiSMR2 Register
0
0
0
1
1
0 or 1
Figure 16.6 U0SMR2 to U4SMR2 Registers
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 171 of 435
External Clock Synchronous Function
Selection
No synchronization
Same division as the external clock
External clock divided by 2
RW
16. Serial I/O
M32C/88 Group (M32C/88T)
UARTi Special Mode Register 3 (i=0 to 4)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
U0SMR3 to U4SMR3
Bit
Symbol
Address
036516, 02E516, 033516, 032516, 02F516
0016
Function
RW
SS Pin Function
Enable Bit(1)
0: Disables SS pin function
1: Enables SS pin function
RW
CKPH
Clock Phase
Set Bit
0: No clock delay
1: Clock delay
RW
DINC
Serial Input Port
Set Bit
0: Selects the TxDi and RxDi pins
(master mode)
1: Selects the STxDi and SRxDi pins
(slave mode)
RW
NODC
Clock Output
Select Bit
0: CMOS output
1: N-channel open drain output
RW
Fault Error Flag(2)
0: No error
1: Error
RW
SSE
ERR
Bit Name
After Reset
b7 b6 b5
DL0
DL1
SDAi Digital Delay
Time Set Bit(3, 4)
DL2
000: No delay
001: 1-to-2 cycles of BRG count source
010: 2-to-3 cycles of BRG count source
011: 3-to-4 cycles of BRG count source
100: 4-to-5 cycles of BRG count source
101: 5-to-6 cycles of BRG count source
110: 6-to-7 cycles of BRG count source
111: 7-to-8 cycles of BRG count source
NOTES:
1. Set the SS pin after the CRD bit in the UiC0 register is set to "1" (CTS/RTS function disabled).
2. The ERR bit is set to "0" by program. It is unchanged if set to "1".
3. Digital delay is generated from a SDAi output by the DL2 to DL0 bits in I2C mode. Set these bits to
"0002" (no delay) except in the I2C mode.
4. When the external clock is selected, approximately 100ns delay is added.
Figure 16.7 U0SMR3 to U4SMR3 Registers
Rev. 1.10 Oct. 18, 2005 Page 172 of 435
REJ09B0162-0110
RW
RW
RW
16. Serial I/O
M32C/88 Group (M32C/88T)
UARTi Special Mode Register 4 (i=0 to 4)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
U0SMR4 to U4SMR4
Bit
Symbol
Address
036416, 02E416, 033416, 032416, 02F416
Bit Name
Function
RW
STAREQ
Start Condition
Generate Bit(1)
0: Clear
1: Start
RW
RSTAREQ
Restart Condition
Generate Bit(1)
0: Clear
1: Start
RW
STPREQ
Stop Condition
Generate Bit(1)
0: Clear
1: Start
RW
STSPSEL
SCL, SDA Output
Select Bit
0: Selects the serial I/O circuit
1: Selects the start/stop condition
generating circuit
RW
ACKD
ACK Data Bit
0: ACK
1: NACK
RW
ACKC
ACK Data Output
Enable Bit
0: Serial I/O data output
1: ACK data output
RW
SCLHI
SCL Output Stop
Enable Bit
0: Disabled
1: Enabled
RW
SWC9
SCL Wait Output Bit 3
0: SCL "L" hold disabled
1: SCL "L" hold enabled
RW
NOTE:
1. When each condition is generated, the STAREQ, RSTAREQ, or STPREQ bit is set to "0".
When a condition generation is incompleted, the bit remains unchanged as "1".
Figure 16.8 U0SMR4 to U4SMR4 Registers
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
After Reset
0016
Page 173 of 435
16. Serial I/O
M32C/88 Group (M32C/88T)
External Interrupt Request Source Select Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
IFSR
Address
031F16
After Reset
0016
Bit
Symbol
Bit Name
IFSR0
INT0 Interrupt Polarity
Select Bit(1)
0: One edge
1: Both edges
RW
IFSR1
INT1 Interrupt Polarity
Select Bit(1)
0: One edge
1: Both edges
RW
IFSR2
INT2 Interrupt Polarity
Select Bit(1)
0: One edge
1: Both edges
RW
IFSR3
INT3 Interrupt Polarity
Select Bit(1)
0: One edge
1: Both edges
RW
IFSR4
INT4 Interrupt Polarity
select bit(1)
0: One edge
1: Both edges
RW
IFSR5
INT5 Interrupt Polarity
Select Bit(1)
0: One edge
1: Both edges
RW
IFSR6
UART0, UART3
Interrupt Source
Select Bit
0: UART3 bus conflict, start condition
detect, stop condition detect
RW
1: UART0 bus conflict, start condition
detect, stop condition detect
IFSR7
UART1, UART4
Interrupt Source
Select Bit
0: UART4 bus conflict, start condition
detect, stop condition detect
RW
1: UART1 bus conflict, start condition
detect, stop condition detect
Function
NOTE:
1. Set this bit to "0" to select a level-sensitive triggering.
When setting this bit to "1", set the POL bit in the INTilC register (i = 0 to 5) to "0" (falling edge).
Figure 16.9 IFSR Register
Rev. 1.10 Oct. 18, 2005 Page 174 of 435
REJ09B0162-0110
RW
16. Serial I/O (Clock Synchronous Serial I/O)
M32C/88 Group (M32C/88T)
16.1 Clock Synchronous Serial I/O Mode
In clock synchronous serial I/O mode, data is transmitted and received with the transfer clock. Table 16.1
lists specifications of clock synchronous serial I/O mode. Table 16.2 lists register settings. Tables 16.3 to
16.5 list pin settings. When UARTi (i=0 to 4) operating mode is selected, the TxDi pin outputs a high-level
("H") signal before transfer starts (the TxDi pin is in a high-impedance state when the N-channel open drain
output is selected). Figure 16.10 shows transmit and receive timings in clock synchronous serial I/O mode.
Table 16.1 Clock Synchronous Serial I/O Mode Specifications
Item
Transfer Data Format
Transfer Clock
Transmit/Receive Control
Transmit Start Condition
Specification
Transfer data : 8 bits long
• The CKDIR bit in the UiMR register (i=0 to 4) is set to "0" (internal clock selected):
fj
(1)
2(m+1) fj=f1, f8, f2n m :setting value of the UiBRG register, 0016 to FF16
• The CKDIR bit is set to "1" (external clock selected) : an input from the CLKi pin
_______
_______
_______ _______
Selected from the CTS function, RTS function or CTS/RTS function disabled
To start transmitting, the following requirements must be met(2):
- Set the TE bit in the UiC1 register to "1" (transmit enabled)
- Set the TI bit in the UiC1 register to "0" (data in the UiTB register)
________
_______
- Apply a low-level ("L") signal to the CTSi pin when the CTS function is selected
Receive Start Condition
To start receiving, the following requirements must be met(2):
- Set the RE bit in the UiC1 register to "1" (receive enabled)
- Set the TE bit to "1" (transmit enabled)
- Set the TI bit to "0" (data in the UiTB register)
Interrupt Request Generation Timing • While transmitting, the following conditions can be selected:
- The UiIRS bit in the UiC1 register is set to "0" (no data in the transmit buffer):
when data is transferred from the UiTB register to the UARTi transmit register (transfer started)
- The UiIRS bit is set to "1" (transmission completed):
when a data transfer from the UARTi transmit register is completed
• While receiving
Error Detection
When data is transferred from the UARTi receive register to the UiRB register (reception completed)
Overrun error(3)
This error occurs when the seventh bit of the next received data is read before reading
the UiRB register
Selectable Function
• CLK polarity
Selectable from the rising edge or falling edge of the transfer clock at transferred data
output or input timing
• LSB first or MSB first
Selectable from data transmission or reception in either bit 0 or in bit 7
• Continuous receive mode
Data can be received simultaneously by reading the UiRB register
• Serial data logic inverse
This function inverses transmitted/received data logically
NOTES:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
2. To start transmission/reception when selecting the external clock, these conditions must be met after the CKPOL
bit in the UiC0 register is set to "0" (data is transmitted on the falling edge of the transfer clock and data is received
on the rising edge) and the CLKi pin is held "H", or when the CKPOL bit is set to "1" (data is transmitted on the rising
edge of the transfer clock and data is received on the falling edge) and the CLKi pin is held "L".
3. If an overrun error occurs, the UiRB register is indeterminate. The IR bit setting in the SiRIC register does not
change to "1" (interrupt requested).
Rev. 1.10 Oct. 18, 2005 Page 175 of 435
REJ09B0162-0110
16. Serial I/O (Clock Synchronous Serial I/O)
M32C/88 Group (M32C/88T)
Table 16.2 Register Settings in Clock Synchronous Serial I/O Mode
Register
UiTB
UiRB
Bit
Function
7 to 0
Set transmit data
7 to 0
Received data can be read
OER
Overrun error flag
UiBRG
7 to 0
Set bit rate
UiMR
SMD2 to SMD0
Set to "0012"
CKDIR
Select the internal clock or external clock
UiC0
IOPOL
Set to "0"
CLK1, CLK0
Select count source for the UiBRG register
CRS
Select CTS or RTS when using either
TXEPT
Transmit register empty flag
CRD
Enables or disables the CTS or RTS function
NCH
Select output format of the TxDi pin
_______
_______
_______
UiC1
_______
CKPOL
Select transmit clock polarity
UFORM
Select either LSB first or MSB first
TE
Set to "1" to enable data transmission and reception
TI
Transmit buffer empty flag
RE
Set to "1" to enable data reception
RI
Reception complete flag
UiIRS
Select what causes the UARTi transmit interrupt to be generated
UiRRM
Set to "1" when using continuous receive mode
UiLCH
Set to "1" when using data logic inverse
SCLKSTPB
Set to "0"
UiSMR
UiSMR2
7 to 0
7 to 0
Set to "0016"
Set to "0016"
UiSMR3
2 to 0
Set to "0002"
UiSMR4
NODC
Select clock output format
7 to 4
Set to "00002"
7 to 0
Set to "0016"
i=0 to 4
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 176 of 435
16. Serial I/O (Clock Synchronous Serial I/O)
M32C/88 Group (M32C/88T)
Table 16.3 Pin Settings in Clock Synchronous Serial I/O Mode (1)
Port
Function
Setting
PS0 Register
PSL0 Register
PD6 Register
PS0_0=0
-
PD6_0=0
__________
P60
CTS0 input
__________
P61
P62
P63
RTS0 output
PS0_0=1
PSL0_0=0
-
CLK0 input
PS0_1=0
-
PD6_1=0
CLK0 output
PS0_1=1
-
-
RxD0 input
PS0_2=0
-
PD6_2=0
TxD0 output
PS0_3=1
-
-
PS0_4=0
-
PD6_4=0
__________
P64
CTS1 input
_________
P65
RTS1 output
PS0_4=1
PSL0_4=0
-
CLK1 input
PS0_5=0
-
PD6_5=0
CLK1 output
PS0_5=1
-
-
P66
RxD1 input
PS0_6=0
-
PD6_6=0
P67
TxD1 output
PS0_7=1
-
-
Table 16.4 Pin Settings (2)
Port
Function
P70(1)
TxD2 output
P71(1)
P72
Setting
PS1 Register
PSL1 Register
PSC Register
PD7 Register
PS1_0=1
PSL1_0=0
PSC_0=0
-
RxD2 input
PS1_1=0
-
-
PD7_1=0
CLK2 input
PS1_2=0
-
-
PD7_2=0
CLK2 output
PS1_2=1
PSL1_2=0
PSC_2=0
-
PS1_3=0
-
-
PD7_3=0
PS1_3=1
PSL1_3=0
PSC_3=0
-
__________
P73
CTS2 input
__________
RTS2 output
NOTE:
1. P70 and P71 are ports for the N-channel open drain output.
Table 16.5 Pin Settings (3)
Port
Function
Setting
PS3 Register(1)
PSL3 Register
PSC3 Register
PD9 Register(1)
CLK3 input
PS3_0=0
-
-
PD9_0=0
CLK3 output
PS3_0=1
-
-
-
P91
RxD3 input
PS3_1=0
-
-
PD9_1=0
P92
TxD3 output
PS3_2=1
PSL3_2=0
-
-
PS3_3=0
PSL3_3=0
-
PD9_3=0
PS3_3=1
-
-
-
P90
__________
P93
CTS3 input
__________
RTS3 output
__________
P94
CTS4 input
PS3_4=0
PSL3_4=0
-
PD9_4=0
RTS4 output
PS3_4=1
-
-
-
CLK4 input
PS3_5=0
PSL3_5=0
-
PD9_5=0
CLK4 output
PS3_5=1
-
-
-
__________
P95
P96
TxD4 output
PS3_6=1
-
PSC3_6=0
-
P97
RxD4 input
PS3_7=0
-
-
PD9_7=0
NOTE:
1. Set the PD9 and PS3 registers immediately after the PRC2 bit in the PRCR register is set to "1" (write enabled). Do
not generate an interrupt or a DMA transfer between the instruction to set the PRC2 bit to "1" and the instruction to
set the PD9 and PS3 registers.
Rev. 1.10 Oct. 18, 2005 Page 177 of 435
REJ09B0162-0110
16. Serial I/O (Clock Synchronous Serial I/O)
M32C/88 Group (M32C/88T)
(1) Transmit Timing (Internal clock selected)
Tc
Transfer Clock
"1"
TE bit in the UiC1
"0"
register
TI bit in the UiC1
register
Data is set in the UiTB register
"1"
"0"
Data is transferred from the UiTB register to the UARTi transmit register
"H"
CTSi
TCLK
"L"
Pulse stops because an "H"
signal is applied to CTSi
Pulse stops because the TE bit is set to "0"
CLKi
TxDi
TXEPT bit in the
UiC0 register
D0 D 1 D2 D3 D4 D5 D6 D7
D0 D 1 D2 D3 D4 D5 D 6 D7
D 0 D1 D2 D 3 D 4 D 5 D6 D7
"1"
"0"
IR bit in the SiTIC "1"
register
"0"
Set to "0" by an interrupt request acknowledgement or by program
The above applies to the following settings:
TC=TCLK=2(m+1)/fj
• The CKDIR bit in the UiMR register is set to "0" (internal clock selected)
fj: Count source frequency set in the UiBRG register (f1, f8, f2n(1))
• The CRD bit in the UiC0 register is set to "0" (RTS/CTS function enabled)
m: Setting value of the UiBRG register
The CRS bit is set to "0" (CTS function selected)
i = 0 to 4
• The CKPOL bit the in UiC0 register is set to "0" (data transmitted on the
NOTE:
falling edge of the transfer clock)
1. The CNT3 to CNT0 bits in the TCSPR register select no division (
• The UiIRS bit in the UiC1 register is set to "0" (no data in the UiTB register)
n=0) or divide-by-2n (n=1 to 15).
(2) Receive Timing (External clock selected)
RE bit in the UiC1
register
"1"
TE bit in the UiC1
register
"1"
TI bit in the UiC1
register
"1"
"0"
Dummy data is set in the UiTB register
"0"
"0"
Data is transferred from the UiTB register to the UARTi transmit register
RTSi
"H"
An "L" signal is applied when
the UiRB register is read
"L"
1 / fEXT
CLKi
Received data is taken in
RxDi
D0 D 1 D2 D3 D4 D 5 D6 D7
RI bit in the UiC1
register
"1"
IR bit in the SiRIC
register
"1"
OER bit in the
UiRB register
"1"
D 0 D1 D2 D3 D 4 D 5
D6
D7
D0 D1 D2 D 3 D4 D 5 D6
Read by the UiRB register
Date is transferred from the UARTi
receive register to the UiRB register
"0"
"0"
Set to "0" by an interrupt request acknowledgement or by program
"0"
The above applies under the following conditions:
• The CKDIR bit in the UiMR register is set to "1" (external clock selected)
• The CRD bit in the UiC0 register is set to "0" (RTS/CTS function enabled)
The CRS bit is set to "1" (RTS function selected)
• The CKPOL bit in the UiC0 register is set to "0"
(Data is received on the rising edge of the transfer clock)
fEXT: External clock frequency i=0 to 4
Figure 16.10 Transmit and Receive Operation
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 178 of 435
The following conditions must be met while an "H" signal is
applied to the CLKi pin before receiving data:
• Set the TE bit in the UiC1 register to "1" (transmit enabled)
• Set the RE bit in the UiC1 register to "1" (receive enabled)
• Write dummy data to the UiTB register
16. Serial I/O (Clock Synchronous Serial I/O)
M32C/88 Group (M32C/88T)
16.1.1 Selecting CLK Polarity Selecting
As shown in Figure 16.11, the CKPOL bit in the UiC0 register (i=0 to 4) determines the polarity of the
transfer clock.
(1) When the CKPOL bit in the UiC0 register (i=0 to 4) is set to "0"
(Data is transmitted on the falling edge of the transfer clock and data is received on the rising edge)
"H"
CLKi "L"
"H"
"L"
D0
D1
D2
D3
D4
D5
D6
D7
"H"
RXDi "L"
D0
D1
D2
D3
D4
D5
D6
D7
TXDi
NOTES:
1. The CLKi pin is held high ("H") when no data is transferred.
2. The above applies when the UFORM bit in the UiC0 register is set to "0" (LSB first)
and the UiLCH bit in the UiC1 register is set to "0" (not inversed).
(2) When the CKPOL bit in the UiC0 register is set to "1"
(Data is transmitted on the rising edge of the transfer clock and data is received on the falling edge)
CLKi
"H"
"L"
TXDi "H"
"L"
D0
D1
D2
D3
D4
D5
D6
D7
RXDi "H"
"L"
D0
D1
D2
D3
D4
D5
D6
D7
NOTES:
3. The CLKi pin is held low ("L") when no data is transferred.
4. The above applies when the UFORM bit in the UiC0 register is set to "0" (LSB first)
and the UiLCH bit in the UiC1 register is set to "0" (not inversed).
Figure 16.11 Transfer Clock Polarity
16.1.2 Selecting LSB First or MSB First
As shown in Figure 16.12, the UFORM bit in the UiC0 register (i=0 to 4) determines a data transfer format.
(1) When the UFORM bit in the UiC0 register (i=0 to 4) is set to "0"
(LSB first)
"H"
CLKi "L"
"H"
TXDi "L"
D0
D1
D2
D3
D4
D5
D6
D7
"H"
"L"
D0
D1
D2
D3
D4
D5
D6
D7
RXDi
NOTE:
1. The above applies when the CKPOL bit in the UiC0 register is set to "0" (data is
transmitted on the falling edge of the transfer clock and received on the rising
edge) and the UiLCH bit in the UiC1 register is set to "0" (not inversed).
(2) When the UFORM bit in the UiC0 register is set to "1" (MSB first)
"H"
CLKi "L"
"H"
"L"
D7
D6
D5
D4
D3
D2
D1
D0
"H"
RXDi "L"
D7
D6
D5
D4
D3
D2
D1
D0
TXDi
NOTE:
2. The above applies when the CKPOL bit in the UiC0 register is set to "0" (data is
transmitted on the falling edge of the transfer clock and received on the rising
edge) and the UiLCH bit in the UiC1 register is set to "0" (not inversed).
Figure 16.12 Transfer Format
Rev. 1.10 Oct. 18, 2005 Page 179 of 435
REJ09B0162-0110
16. Serial I/O (Clock Synchronous Serial I/O)
M32C/88 Group (M32C/88T)
16.1.3 Continuous Receive Mode
When the UiRRM bit in the UiC1 register (i=0 to 4) is set to "1" (continuous receive mode), the TI bit is set
to "0" (data in the UiTB register) by reading the UiRB register. When the UiRRM bit is set to "1", do not set
dummy data in the UiTB register by program.
16.1.4 Serial Data Logic Inverse
When the UiLCH bit (i=0 to 4) in the UiC1 register is set to "1" (inverse), data logic written in the UiTB
register is inversed when transmitted. The inversed receive data logic can be read by reading the UiRB
register. Figure 16.13 shows a switching example of the serial data logic.
(1) When the UiLCH bit in the UiC1 register (i=0 to 4) is set to "0" (not inversed)
Transfer clock
"H"
"L"
TxDi
"H"
(no inverse) "L"
D0
D1
D2
D3
D4
D5
D6
D7
(2) When the UiLCH bit in the UiC1 register is set to "1" (inverse)
Transfer clock
"H"
"L"
TxDi
"H"
(inverse) "L"
D0
D1
D2
D3
D4
D5
D6
D7
NOTE:
1. The above applies when the CKPOL bit in the UiC0 register is set to "0" (data is transmitted on
the falling edge) and the UFORM bit in the UiC0 register is set to "0" (LSB first).
Figure 16.13 Serial Data Logic Inverse
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 180 of 435
16. Serial I/O (UART)
M32C/88 Group (M32C/88T)
16.2 Clock Asynchronous Serial I/O (UART) Mode
In UART mode, data is transmitted and received after setting a desired bit rate and data transfer format.
Table 16.6 lists specifications of UART mode.
Table 16.6 UART Mode Specifications
Item
Transfer Data Format
Specification
• Character bit (transfer data) : selected from 7 bits, 8 bits, or 9 bits long
• Start bit: 1 bit long
• Parity bit: selected from odd, even, or none
Transfer Clock
• Stop bit: selected from 1 bit or 2 bits long
• The CKDIR bit in the UiMR register is set to "0" (internal clock selected):
fj/16(m+1) fj = f1, f8, f2n(1) m: setting value of the UiBRG register , 0016 to FF16
• The CKDIR bit is set to "1" (external clock selected):
Transmit/Receive Control
Transmit Start Condition
fEXT/16(m+1)
fEXT: clock applied to the CLKi pin
_______
_______
_______ _______
Select from CTS function, RTS function or CTS/RTS function disabled
To start transmitting, the following requirements must be met:
- Set the TE bit in the UiC1 register to "1" (transmit enabled)
- Set the TI bit in the UiC1 register to "0" (data in the UiTB register)
_______
_______
- Apply a low-velel ("L") signal to the CTSi pin when the CTS function is selected
Receive Start Condition
Interrupt Request
Generation Timing
To start receiving, the following requirements must be met:
- Set the RE bit in the UiC1 register to "1" (receive enabled)
- The start bit is detected
While transmitting, the following condition can be selected:
- The UiIRS bit in the UiC1 register is set to "0" (no data in the UiTB register):
when data is transferred from the UiTB register to the UARTi transmit register (transfer started)
- The UiIRS bit is set to "1" (transmission completed):
when data transmission from the UARTi transfer register is completed
While receiving
Error Detect
when data is transferred from the UARTi receive register to the UiRB register (reception completed)
• Overrun error(2)
This error occurs when the bit before the last stop bit of the next received data is read
prior to reading the UiRB register (the first stop bit when selecting 2 stop bits)
• Framing error
This error occurs when the number of stop bits set is not detected
• Parity error
When parity is enabled, this error occurs when the number of "1" in parity and character bits does not match the number of "1" set
• Error sum flag
Selectable Function
This flag is set to "1" when any of an overrun, framing or parity errors occur
• LSB first or MSB first
Selectable from data transmission or reception in either bit 0 or in bit 7
•Serial data logic inverse
Logic values of data to be transmitted and received data are inversed. The start bit
and stop bit are not inversed
•TxD and RxD I/O polarity Inverse
TxD pin output and RxD pin input are inversed. All I/O data levels are also inversed
NOTES:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
2. If an overrun error occurs, the UiRB register is indeterminate. The IR bit setting in the SiRIC register does not
change to "1" (interrupt requested).
Rev. 1.10 Oct. 18, 2005 Page 181 of 435
REJ09B0162-0110
16. Serial I/O (UART)
M32C/88 Group (M32C/88T)
Table 16.7 lists register settings. Tables 16.8 to 16.10 list pin settings. When UARTi (i=0 to 4) operating
mode is selected, the TxDi pin outputs a high-level ("H") signal before transfer is started (the TxDi pin is in
a high-impedance state when the N-channel open drain output is selected). Figure 16.14 shows an example of a transmit operation in UART mode. Figure 16.15 shows an example of a receive operation in
UART mode.
Table 16.7 Register Settings in UART Mode
Register
Bit
Function
UiTB
8 to 0
Set transmit data(1)
UiRB
8 to 0
Received data can be read(1)
OER, FER,
Error flags
PER, SUM
UiBRG
7 to 0
UiMR
SMD2 to SMD0
Set bit rate
Set to "1002" when transfer data is 7 bits long
Set to "1012" when transfer data is 8 bits long
Set to "1102" when transfer data is 9 bits long
CKDIR
UiC0
Select the internal clock or external clock
STPS
Select stop bit length
PRY, PRYE
Select parity enable or disable, odd or even
IOPOL
Select TxD and RxD I/O polarity
CLK1, CLK0
Select count source for the UiBRG register
CRS
Select either CTS or RTS when using either
TXEPT
Transfer register empty flag
CRD
Select the CTS or RTS function enabled or disabled
NCH
Select output format of the TxDi pin
_______
________
_______
_______
CKPOL
Set to "0"
UFORM
Select the LSB first or MSB first when a transfer data is 8 bits long
Set to "0" when transfer data is 7 bits or 9 bits long
UiC1
TE
Set to "1" to enable data transmission
TI
Transfer buffer empty flag
RE
Set to "1" to enable data reception
RI
Reception complete flag
UiIRS
Select what causes the UARTi transmit interrupt to be generated
UiRRM
Set to "0"
UiLCH
Select whether data logic is inversed or not inversed when a transfer data is
UiERE
Set to either "0" or "1"
UiSMR
7 to 0
Set to "0016"
UiSMR2
7 to 0
Set to "0016"
UiSMR3
7 to 0
Set to "0016"
UiSMR4
7 to 0
Set to "0016"
7 bits or 8 bits long. Set to "0" when transfer data is 9 bits long
NOTE:
1. Use bits 0 to 6 when transfer data is 7 bits long, bits 0 to 7 when 8 bits long, bits 0 to 8 when 9 bits long.
Rev. 1.10 Oct. 18, 2005 Page 182 of 435
REJ09B0162-0110
16. Serial I/O (UART)
M32C/88 Group (M32C/88T)
Table 16.8 Pin Settings in UART Mode (1)
Port
Function
Setting
PS0 Register
PSL0 Register
PD6 Register
PS0_0=0
–
PD6_0=0
__________
P60
CTS0 input
__________
RTS0 output
PS0_0=1
PSL0_0=0
–
P61
CLK0 input
PS0_1=0
–
PD6_1=0
P62
RxD0 input
PS0_2=0
–
PD6_2=0
P63
TxD0 output
PS0_3=1
–
–
__________
P64
CTS1 input
PS0_4=0
–
PD6_4=0
RTS1 output
PS0_4=1
PSL0_4=0
–
P65
CLK1 input
PS0_5=0
–
PD6_5=0
P66
RxD1 input
PS0_6=0
–
PD6_6=0
P67
TxD1 output
PS0_7=1
–
–
__________
Table 16.9 Pin Settings (2)
Port
Function
Setting
PS1 Register
PSL1 Register
PSC Register
PD7 Register
PS1_0=1
PSL1_0=0
PSC_0=0
–
RxD2 input
PS1_1=0
–
–
PD7_1=0
CLK2 input
PS1_2=0
–
–
PD7_2=0
PS1_3=0
–
–
PD7_3=0
PS1_3=1
PSL1_3=0
PSC_3=0
–
PSL3 Register
PSC3 Register
PD9 Register(1)
PD9_0=0
P70(1)
TxD2 output
P71(1)
P72
__________
P73
CTS2 input
__________
RTS2 output
NOTE:
1. P70 and P71 are ports for the N-channel open drain output.
Table 16.10 Pin Settings (3)
Port
Function
Setting
PS3
Register(1)
P90
CLK3 input
PS3_0=0
–
–
P91
RxD3 input
PS3_1=0
–
–
PD9_1=0
P92
TxD3 output
PS3_2=1
PSL3_2=0
–
–
PS3_3=0
PSL3_3=0
–
PD9_3=0
PS3_3=1
–
–
–
PS3_4=0
PSL3_4=0
–
PD9_4=0
PS3_4=1
–
–
–
__________
P93
CTS3 input
__________
RTS3 output
__________
P94
CTS4 input
__________
RTS4 output
P95
CLK4 input
PS3_5=0
PSL3_5=0
–
PD9_5=0
P96
TxD4 output
PS3_6=1
–
PSC3_6=0
–
P97
RxD4 input
PS3_7=0
–
–
PD9_7=0
NOTE:
1. Set the PD9 and PS3 registers set immediately after the PRC2 bit in the PRCR register is set to "1" (write enabled).
Do not generate an interrupt or a DMA transfer between the instruction to set to the PRC2 bit to "1" and the
instruction to set the PD9 and PS3 registers.
Rev. 1.10 Oct. 18, 2005 Page 183 of 435
REJ09B0162-0110
16. Serial I/O (UART)
M32C/88 Group (M32C/88T)
(1) 8-bit Data Transmit Timing (with a parity and 1 stop bit)
Tc
The transfer clock stops momentarily, because an "H" signal is applied to the CTS pin,
when the stop bit state is verified.
The transfer clock resumes running as soon as an "L" signal is applied to the CTS pin
Transfer Clock
TE bit in the UiC1
register
"1"
TI bit in the UiC1
register
"1"
"0"
Data is set in the UiTB register
"0"
Data is transferred from the UiTB register to the UARTi transmit register
"H"
CTSi
"L"
Parity
bit
Start
bit
ST D0 D1 D2 D3 D4 D5 D6 D7
TxDi
TXEPT bit in the
UiC0 register
"1"
IR bit in the SiTIC
register
"1"
P
Stop
bit
Pulse stops because the TE bit is set to "0"
ST D0 D1 D2 D3 D4 D5 D6 D7
SP
P
ST D0 D1
SP
"0"
"0"
Set to "0" by an interrupt request acknowledgement or by program
i=0 to 4
The above timing diagram applies under the following conditions:
• The PRYE bit in the UiMR register is set to "1" (parity enabled)
• The STPS bit in the UiMR register is set to "0" (1 stop bit)
• The CRD bit in the UiC0 register is set to "0" and the CRS bit is set
to "0" (CTS function selected)
• The UilRS bit in the UiC1 register is set to "1"
(transmission completed)
Tc = 16 (m + 1) / fj or 16 (m + 1) / fEXT
fj: count source frequency set in the UiBRG register (f1, f8, f2n(1))
fEXT: count source frequency set in the UiBRG register (external
clock)
m: setting value of the UiBRG register
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0)
or divide-by-2n (n=1 to 15).
(2) 9-bit Data Transmit Timing (with no parity and 2 stop bits)
Tc
Transfer Clock
TE bit in the UiC1
register
TI bit in the UiC1
register
"1"
Data is set in the UiTB register
"0"
"1"
"0"
Data is transferred from the UiTB register to the UARTi transmit register
Stop
Stop
bit
bit
Start
bit
TxDi
ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SP SP
TXEPT bit in the
UiC0 register
"1"
IR bit in the SiTIC
register
"1"
ST D0 D1 D2 D3 D4 D5 D6 D7 D8
SP SP
ST D0 D1
"0"
"0"
Set to "0" by an interrupt request acknowledgement or by program
i=0 to 4
The above applies under the following conditions:
• The PRYE bit in the UiMR register is set to "0" (parity disabled)
• The STPS bit in the UiMR register is set to "1" (2 stop bits)
• The CRD bit in the UiC0 register is set to "1" (CTS function
disabled)
• The UilRS bit in the UiC1 register is set to "0" (no data in the
transmit buffer)
Figure 16.14 Transmit Operation
Rev. 1.10 Oct. 18, 2005 Page 184 of 435
REJ09B0162-0110
Tc = 16 (m + 1) / fj or 16 (m + 1) / fEXT
fj: count source frequency set in the UiBRG register (f1, f8, f2n(1))
fEXT: count source frequency set in the UiBRG register (external
clock)
m: setting value of the UiBRG register
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division
(n=0) or divide-by-2n (n=1 to 15).
16. Serial I/O (UART)
M32C/88 Group (M32C/88T)
8-bit Data Receive Timing (with no parity and 1 stop bit)
UiBRG register
setting output
RE bit in the
UiC1 register
"1"
"0"
Stop bit
Start bit
RxDi
D1
D0
Verify if an "L"
signal is applied
D7
Capture a received data
Transfer Clock
RI bit in the UiC1
register
RTSi
IR bit in the
SiRIC register
Data is transferred from the UARTi receive
Start receiving when the transfer clock is
"1" generated on the falling edge of the start bit register to the UiRB register
"0"
"H"
"L"
Change to "L" by reading the UiRB register
"1"
"0"
Set to "0" by an interrupt request acknowledgement or by program
i=0 to 4
NOTE:
1. The above applies when the PRYE bit in the UiMR register is set to "0" (parity disabled),
the STPS bit in the UiMR register is set to "0" (1 stop bit) and the CRS bit in the UiC0 register is set
to "1" (RTS function selected).
Figure 16.15 Receive Operation
16.2.1 Bit Rate
In UART mode, bit rate is clock frequency which is divided by a setting value of the UiBRG (i=0 to 4)
register and again divided by 16. Table 16.11 lists an example of bit rate setting.
Table 16.11 Bit Rate
Bit Rate
(bps)
Count
Source
of
UiBRG
Peripheral Function Clock:
16MHz
Setting Value
of UiBRG: n
Actual Bit Rate
(bps)
Peripheral Function Clock:
24MHz
Setting Value
of UiBRG: n
Actual Bit Rate
(bps)
Peripheral Function Clock:
32MHz
Setting Value
of UiBRG: n
Actual Bit Rate
(bps)
1200
f8
103 (67h)
1202
155 (96h)
1202
207 (CFh)
1202
2400
f8
51 (33h)
2404
77 (46h)
2404
103 (67h)
2404
4800
f8
25 (19h)
4808
38 (26h)
4808
51 (33h)
4808
9600
f1
103 (67h)
9615
155 (96h)
9615
207 (CFh)
9615
14400
f1
68 (44h)
14493
103 (67h)
14423
138 (8Ah)
14388
19200
f1
51 (33h)
19231
77 (46h)
19231
103 (67h)
19231
28800
f1
34 (22h)
28571
51 (33h)
28846
68 (44h)
28986
31250
f1
31 (1Fh)
31250
47 (2Fh)
31250
63 (3Fh)
31250
38400
f1
25 (19h)
38462
38 (26h)
38462
51 (33h)
38462
51200
f1
19 (13h)
50000
28 (1Ch)
51724
38 (26h)
51282
Rev. 1.10 Oct. 18, 2005 Page 185 of 435
REJ09B0162-0110
16. Serial I/O (UART)
M32C/88 Group (M32C/88T)
16.2.2 Selecting LSB First or MSB First
As shown in Figure 16.16, the UFORM bit in the UiC0 register (i=0 to 4) determines data transfer format.
This function is available for 8-bit transfer data.
(1) When the UFORM Bit in the UiC0 Register (i=0 to 4) is set to "0" (LSB first)
CLKi
"H"
"L"
TxDi
"H"
"L"
RxDi
ST
D0
D1
D2
D3
D4
D5
D6
D7
P
SP
ST
D0
D1
D2
D3
D4
D5
D6
D7
P
SP
"H"
"L"
(2) When the UFORM Bit in the UiC0 Register is set to "1" (MSB first)
CLKi
"H"
"L"
TxDi "H"
ST
D7
D6
D5
D4
D3
D2
D1
D0
P
SP
"H"
"L"
ST
D7
D6
D5
D4
D3
D2
D1
D0
P
SP
"L"
RxDi
NOTE:
1. The above applies when the CKPOL bit in the UiC0 register is set to "0" (data is
transmitted on the falling edge of the transfer clock and received on the rising edge)
and the UiLCH bit in the UiC1 register is set to "0" (no inverse).
ST: Start bit
P: Parity bit
SP: Stop bit
Figure 16.16 Transfer Format
16.2.3 Serial Data Logic Inverse
When the UiLCH bit (i=0 to 4) in the UiC1 register is set to "1" (inverse), data logic written in the UiTB
register is inversed when transmitted. The inversed receive data logic can be read by reading the UiRB
register. Figure 16.17 shows a switching example of the serial data logic.
(1) When the UiLCH bit in the UiC1 register (i=0 to 4) is set to "0" (no inverse)
Transfer Clock
"H"
"L"
TxDi
"H"
(no inverse)
"L"
ST
D0
D1
D2
D3
D4
D5
D6
D7
P
SP
D7
P
SP
(2) When the UiLCH bit in the UiC1 register is set to "1" (inverse)
Transfer Clock
"H"
"L"
TxDi
"H"
(inverse) "L"
ST
D0
D1
D2
D3
D4
D5
D6
NOTE:
1. The above applies when the UFORM bit in the UiC0 register is set to "0" (
LSB first), the STPS bit in the UiMR register is set to "0" (1 stop bit) and the
PRYE bit is set to "1" (parity enabled).
Figure 16.17 Serial Data Logic Inverse
Rev. 1.10 Oct. 18, 2005 Page 186 of 435
REJ09B0162-0110
ST: Start bit
P: Parity bit
SP: Stop bit
16. Serial I/O (UART)
M32C/88 Group (M32C/88T)
16.2.4 TxD and RxD I/O Polarity Inverse
TxD pin output and RxD pin input are inversed. All I/O data level, including the start bit, stop bit and parity
bit, are inversed. Figure 16.18 shows TxD and RxD I/O polarity inverse.
(1) When the IOPOL bit in the UiMR register (i=0 to 4) is set to "0" (no inverse)
Transfer Clock
"H"
"L"
TxDi
"H"
(no inverse)
"L"
RxDi
"H"
(no inverse)
"L"
ST
D0
D1
D2
D3
D4
D5
D6
D7
P
SP
ST
D0
D1
D2
D3
D4
D5
D6
D7
P
SP
(2) When the IOPOL bit in the UiMR register is set to "1" (inverse)
Transfer Clock
"H"
TxDi
"H"
"L"
(inverse) "L"
RxDi
"H"
(inverse)
"L"
ST
D0
D1
D2
D3
D4
D5
D6
D7
P
SP
ST
D0
D1
D2
D3
D4
D5
D6
D7
P
SP
NOTE:
1. The above applies when the UFORM bit in the UiC0 register is set to "0" (LSB
first), the STPS bit in the UiMR bit is set to "0" (1 stop bit) and the PRYE bit is
set to "1" (parity enabled).
Figure 16.18 TxD and RxD I/O Polarity Inverse
Rev. 1.10 Oct. 18, 2005 Page 187 of 435
REJ09B0162-0110
ST: Start bit
P: Even parity
SP: Stop bit
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
16.3 Special Mode 1 (I2C Mode)
I2C mode is a mode to communicate with external devices with a simplified I2C. Table 16.12 lists specifications of I2C mode. Table 16.13 lists register settings, Table 16.14 lists each function. Figure 16.19 shows
a block diagram of I2C mode. Figure 16.20 shows timings for transfer to the UiRB register (i=0 to 4) and
interrupts. Tables 16.15 to 16.17 list pin settings.
As shown in Table 16.12, I2C mode is entered when the SMD2 to SMD0 bits in the UiMR register is set to
"0102" and the IICM bit in the UiSMR register is set to "1". Output signal from the SDAi pin changes after
the SCLi pin level becomes low ("L") and stabilizes due to a SDAi transmit output via the delay circuit.
Table 16.12 I2C Mode Specifications
Item
Interrupt
Specifications
Start condition detect, stop condition detect, no acknowledgment detect, acknowledgment
detect
Selectable Function
• Arbitration lost
Selectable from update timing of the ABT bit in the UiRB register.
Refer to 16.3.3 Arbitration
• SDAi digital delay
Selectable from no digital delay or 2 to 8 cycle delay of the count source of the UiBRG
register. Refer to 16.3.5 SDA Output
• Clock phase setting
Selectable from clock delay or no clock delay. Refer to 16.3.4 Transfer Clock
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 188 of 435
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
SDAi
(Note1)
Timer
To DMA
I/O
UARTi
IICM 1
Delay Circuit
0
SDHI
D
Q
IICM=1 and
IICM2=0
To DMA
Arbitration
1
0
IICM=0 or
IICM2=1
IICM
Receive Register
UARTi
S
Stop Condition Detection
Falling Edge
Detection
SCLi
Noise
Filter
Q
Bus
busy
NACK
D Q
T
LSYN bit
D Q
T
R
I/O
Data Register
ACK
9th Pulse
Internal Clock
UARTi
Noise
Filter
R
IICM=1
1 IICM
Bus Conflict
SWC2 CLK
Detection
Control
UARTi
External Clock
1
0
IICM
0
QR
S
Falling Edge of 9th Pulse
SWC
Port reading
(Note 1)
CLKi
UARTi
IICM=0
I/O
Timer
i=0 to 4
NOTE:
1. Set the PSj (j=0,1,3), PSLj, or PSC register to determine.
IICM: Bit in the UiSMR register
IICM2: Bit in the UiSMR2 register
Figure 16.19 I2C Mode Block Diagram
Rev. 1.10 Oct. 18, 2005 Page 189 of 435
REJ09B0162-0110
UARTi Reception
ACK Interrupt Request
DMA Request
IICM=1 and
IICM2=0
Start Condition Detection
(Note 1)
UARTi Transmission
NACK Interrupt
Request
UARTi
ALS
T
Noise
Filter
IICM=0 or IICM2=1
Transmit Register
* When the IICM bit is set to "1", port pin can be read
regardless of the direction register being set to "1" (
output).
Bus Conflict
Start Condition Detection
Stop Condition Detection
Interrupt Request
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.13 Register Settings in I2C Mode
Register
Bit
Function
Master
UiTB
UiRB
UiBRG
UiMR
UiC0
UiC1
UiSMR
UiSMR2
UiSMR3
UiSMR4
IFSR
i=0 to 4
Slave
7 to 0
7 to 0
8
ABT
OER
7 to 0
SMD2 to SMD0
CKDIR
IOPOL
CLK1, CLK0
CRS
TXEPT
CRD, NCH
CKPOL
UFORM
TE
TI
RE
RI
UiRRM, UiLCH,
UiERE
IICM
ABC
BBS
7 to 3
IICM2
CSC
SWC
Set transmit data
Received data can be read
ACK or NACK bit can be read
Arbitration lost detect flag
Overrun error flag
Set bit rate
Set to "0102"
Set to "0"
Set to "0"
Select count source of the UiBRG register
Disabled because the CRD bit is set to "1"
Transfer register empty flag
Set to "1"
Set to "0"
Set to "1"
Set to "1" to enable data transmission
Transfer buffer empty flag
Set to "1" to enable data reception
Reception complete flag
Set to "0"
STSPSEL
ACKD
ACKC
SCLHI
Set to "1" when using a condition generating function
Select ACK or NACK
Set to "1" for ACK data output
Set to "1" to enable SCL output stop when
Not used. Set to "0"
SWC9
detecting stop condition
Not used. Set to "0"
IFSR6, IFSR7
Set to "1"
Disabled
Disabled
Set to "1"
Disabled
Set to "1"
Select an arbitration lost detect timing
Disabled
Bus busy flag
Set to "000002"
See Table 16.14
Set to "1" to enable clock synchronization
Set to "0"
Set to "1" to fix an "L" signal output from SCLi on the falling edge of the ninth bit
of the transfer clock
ALS
Set to "1" to terminate SDAi output when
Not used. Set to "0"
detecting the arbitration lost
STC
Not used. Set to "0"
Set to "1" to reset UARTi
by detecting the start condition
SWC2
Set to "1" for an "L" signal output from SCL forcibly
SDHI
Set to "1" to disable SDA output
SU1HIM
Set to "0"
SSE
Set to "0"
CKPH
See Table 16.14
DINC, NODC, ERR Set to "0"
DL2 to DL0
Set digital delay value
STAREQ
Set to "1" when generating a start condition
Not used. Set to "0"
RSTAREQ
Set to "1" when generating a restart condition
STPREQ
Set to "1" when generating a stop condition
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 190 of 435
Set to "1" to fix an "L" signal output
from SCLi on the falling edge of the
ninth bit of the transfer clock
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.14 I2C Mode Functions
I2 C Mode (SMD2 to SMD0=0102, IICM=1)
Function
Clock Synchronous
Serial I/O Mode
(SMD2 to SMD0=0012,
IICM=0)
IICM2=0
(NACK/ACK interrupt)
IICM2=1
(UART transmit/UART receive interrupt)
CKPH=0
(No clock delay)
CKPH=0
(No clock delay)
CKPH=1
(Clock delay)
CKPH=1
(Clock delay)
Source for Interrupt
Numbers 39 to 41(1)
(See Figure 16.20)
-
Start condition or stop condition detection (See Table 16.18)
Source for Interrupt
Numbers 17, 19, 33, 35,
and 37(1)
(See Figure 16.20)
UARTi transmission Transmission started or
completed (selected by
the UiIRS register)
No acknowledgement detection
(NACK) Rising edge of 9th bit of SCLi
UARTi
transmission Rising edge of
9th bit of SCLi
Source for Interrupt
Numbers 18, 20, 34, 36,
and 38(1)
(See Figure 16.20)
UARTi reception Receiving at 8th bit
CKPOL=0(rising edge)
CKPOL=1(falling edge)
Acknowledgement detection
(ACK) Rising edge of 9th bit of SCLi
UARTi Reception Falling edge of 9th bit of SCLi
Data Transfer Timing from
the UART Receive Shift
Register to the UiRB Register
CKPOL=0(rising edge)
CKPOL=1(falling edge)
Rising edge of 9th bit of SCLi
Falling edge of
9th bit of SCLi
UARTi Transmit Output
Delay
No delay
Delay
P63, P67, P70, P92, P96
Pin Functions
TxDi output
SDAi input and output
P62, P66, P71, P91, P97
Pin Functions
RxDi input
SCLi input and output
P61, P65, P72, P90, P95
Pin Functions
Select CLKi input or
output
– (Not used in I2 C mode)
Noise Filter Width
15 ns
200 ns
Reading RxDi and SCLi
Pin Levels
Can be read if port
direction bit is set to "0"
Can be read regardless of the port direction bit
Default Value of TxDi and
SDAi Output
CKPOL=0 (H)
CKPOL=1 (L)
Values set in the port register before entering I2 C mode( 2 )
SCLi Default and End
Values
–
H
Source for DMA
(See Figure 16.20)
UARTi reception
Acknowledgement detection
(ACK)
Store Received Data
Reading Received Data
1st to 8th bits of the
received data are stored
into bits 7 to 0 in the
UiRB register
L
1st to 8th bits of the received
data are stored into bits 7 to 0
in the UiRB register
The UiRB register status is read
H
UARTi transmission Next falling edge after the
9th bit of SCLi
Falling edge and rising edge
of 9th bit of SCLi
L
UARTi reception Falling edge of 9th bit of SCLi
1st to 7th bits of the received data are stored
into bits 6 to 0 in the UiRB register. 8th bit is
stored into bit 8 in the UiRB register.
1st to 8th bits are stored into
bits 7 to 0 in the UiRB
register(3 )
Bits 6 to 0 in the UiRB
registerts( 4 ) are read as bit 7
to 1. Bit 8 in the UiRB
register is read as bit 0
i=0 to 4
NOTES:
1. Use the following procedure to change what causes an interrupt to be generated.
(a) Disable interrupt of corresponding interrupt number.
(b) Change what causes an interrupt to be generated.
(c) Set the IR bit of a corresponding interrupt number to "0" (no interrupt requested).
(d) Set the ILVL2 to ILVL0 bits of a corresponding interrupt number.
2. Set default value of the SDAi output when the SMD2 to SMD0 bits in the UiMR register are set to "0002"
(serial I/O disabled).
3. Second data transfer to the UiRB register (on the rising edge of the ninth bit of SCLi).
4. First data transfer to the UiRB register (on the falling edge of the ninth bit of SCLi).
Rev. 1.10 Oct. 18, 2005 Page 191 of 435
REJ09B0162-0110
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
(1) When the IICM2 bit is set to "0" (ACK or NACK interrupt) and the CKPH bit is set to "0" (No clock delay)
1st
bit
2nd
bit
3rd
bit
4th
bit
5th
bit
6th
bit
7th
bit
8th
bit
9th
bit
SCLi
SDAi
D7
D6
D5
D4
D3
D2
D1
D0
D8 (ACK or NACK)
ACK interrupt (DMA
request) or NACK interrupt
b15
Data is transferred to the UiRB register
b9
b8
b7
b0
D8 D7 D 6 D 5 D4 D3 D2 D1 D 0
•••
Contents of the UiRB register
(2) When the IICM2 bit is set to "0" and the CKPH bit is set to "1" (clock delay)
1st
bit
2nd
bit
3rd
bit
4th
bit
5th
bit
6th
bit
7th
bit
8th
bit
9th
bit
SCLi
SDAi
D7
D6
D5
D4
D3
D2
D1
D0
D8 (ACK or NACK)
ACK interrupt (DMA
request) or NACK interrupt
b15
Data is transferred to the UiRB register
b9
•••
b8
b7
b0
D8 D7 D6 D 5 D 4 D3 D2 D1 D0
Contents of the UiRB register
(3) When the IICM2 bit is set to "1" (UART transmit or receive interrupt) and the CKPH bit is set to "0"
1st
bit
2nd
bit
3rd
bit
4th
bit
5th
bit
6th
bit
7th
bit
8th
bit
9th
bit
SCLi
SDAi
D7
D6
D5
D4
D3
D2
D1
D8 (ACK or NACK)
D0
Receive interrupt
(DMA request)
Transmit interrupt
b15
Data is transferred to the UiRB register
b9
b8
b7
D0
•••
b0
D7 D6 D5 D4 D 3 D 2 D 1
Contents of the UiRB register
(4) When the IICM2 bit is set to "1" and the CKPH bit is set to "1"
1st
bit
2nd
bit
3rd
bit
4th
bit
5th
bit
6th
bit
7th
bit
8th
bit
9th
bit
SCLi
SDAi
D7
D6
D5
D4
D3
D2
D1
D0
D8 (ACK or NACK)
Receive interrupt
(DMA request)
Data is transferred to the UiRB register
b15
b9
•••
i=0 to 4
IICM2: Bit in the UiSMR2 register
CKPH: Bit in the UiSMR3 regiser
b8
D0
b7
b0
D7 D6 D 5 D 4 D3 D2 D1
Contents of the UiRB register
The above timing diagram applies under the following condition:
• The CKDIR bit in the UiMR register is set to "1" (slave)
Figure 16.20 SCLi Timing
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 192 of 435
Transmit interrupt
Data is transferred to the UiRB register
b15
b9
•••
b8
b7
b0
D 8 D7 D6 D5 D 4 D 3 D2 D 1 D0
Contents of the UiRB register
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.15 Pin Settings in I2C Mode (1)
Port
Function
Setting
PS0 Register
P62
P63
P66
P67
PSL0 Register
PD6 Register
SCL0 output
PS0_2=1
PSL0_2=0
-
SCL0 input
PS0_2=0
-
PD6_2=0
SDA0 output
PS0_3=1
-
-
SDA0 input
PS0_3=0
-
PD6_3=0
SCL1 output
PS0_6=1
PSL0_6=0
-
SCL1 input
PS0_6=0
-
PD6_6=0
SDA1 output
PS0_7=1
-
-
SDA1 input
PS0_7=0
-
PD6_7=0
Table 16.16 Pin Settings (2)
Setting
Port
Function
PS1 Register
PSL1 Register PSC Register PD7 Register
SDA2 output
PS1_0=1
PSL1_0=0
PSC_0=0
–
SDA2 input
PS1_0=0
–
–
PD7_0=0
SCL2 output
PS1_1=1
PSL1_1=1
PSC_1=0
–
SCL2 input
PS1_1=0
–
–
PD7_1=0
P70( 1 )
P71( 1 )
NOTE:
1. P70 and P71 are ports for the N-channel open drain output.
Table 16.17 Pin Settings (3)
Port
Function
Setting
PS3
P91
P92
P96
P97
Register(1)
PSL3 Register
PSC3 Register
PD9 Register(1)
SCL3 output
PS3_1=1
PSL3_1=0
-
-
SCL3 input
PS3_1=0
-
-
PD9_1=0
SDA3 output
PS3_2=1
PSL3_2=0
-
-
SDA3 input
PS3_2=0
-
-
PD9_2=0
SDA4 output
PS3_6=1
-
PSC3_6=0
-
SDA4 input
PS3_6=0
-
-
PD9_6=0
SCL4 output
PS3_7=1
PSL3_7=0
-
-
SCL4 input
PS3_7=0
-
-
PD9_7=0
NOTE:
1. Set the PD9 and PS3 registers immediately after the PRC2 bit in the PRCR register is set to "1" (write enabled).
Do not generate an interrupt or a DMA transfer between the instruction to set to the PRC2 bit to "1" and the
instruction to set the PD9 and PS3 registers.
Rev. 1.10 Oct. 18, 2005 Page 193 of 435
REJ09B0162-0110
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
16.3.1 Detecting Start Condition and Stop Condition
The microcomputer detects either a start condition or stop condition. The start condition detect interrupt
is generated when the SCLi (i=0 to 4) pin level is held high ("H") and the SDAi pin level changes "H" to low
("L"). The stop condition detect interrupt is generated when the SCLi pin level is held "H" and the SDAi pin
level changes "L" to "H". The start condition detect interrupt shares interrupt control registers and vectors
with the stop condition detect interrupt. The BBS bit in the UiSMR register determines which interrupt is
requested.
3 to 6 cycles < setup time(1)
3 to 6 cycles < hold time(1)
Setup time
Hold time
SCLi
SDAi
(Start condition)
SDAi
(Stop condition)
i=0 to 4
NOTE:
1. These cycles are main clock generation frequency cycles f(XIN).
Figure 16.21 Start Condition or Stop Condition Detecting
16.3.2 Start Condition or Stop Condition Output
The start condition is generated when the STAREQ bit in the UiSMR4 register (i=0 to 4) is set to "1"
(start). The restart condition is generated when the RSTAREQ bit in the UiSMR4 register is set to "1"
(start). The stop condition is generated the STPREQ bit in the UiSMR4 is set to "1" (start).
The start condition is output when the STAREQ bit is set to "1" and the STSPSEL bit in the UiSMR4
register is set to "1" (start or stop condition generating circuit selected). The restart condition output is
provided when the RSTAREQ bit and STSPSEL bit are set to "1". The stop condition output is provided
when the STPREQ bit and the STSPSEL bit are set to "1".
When the start condition, stop condition or restart condition is output, do not generate an interrupt between the instruction to set the STAREQ bit, STPREQ bit or RSTAREQ bit to "1" and the instruction to set
the STSPSEL bit to "1". When the start condition is output, set the STAREQ bit to "1" before the
STSPSEL bit is set to "1".
Table 16.18 lists function of the STSPSEL bit. Figure 16.22 shows functions of the STSPSEL bit.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 194 of 435
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.18 STSPSEL Bit Function
Function
STSPSEL = 0
STSPSEL = 1
Start condition and stop
condition output
Program with ports determines how the
start condition or stop condition is
output
The STAREQ bit, RSTAREQ bit and
STPREQ bit determine how the start
condition or stop condition is output
Timing to generate start
condition and stop condition
interrupt requests
Start condition and stop condition are
detected
Start condition and stop condition
generation are completed
(1) In slave mode,
The CKDIR bit is set to "1" (external clock)
The STSPSEL bit is set to "0" (no start condition and stop condition output)
SCLi
SDAi
Start condition detect
interrupt
Stop condition detect
interrupt
(2) In master mode,
The CKDIR bit is set to "0" (internal clock)
The STSPSEL bit is set to "1" (start condition and stop condition output)
Setting value of
the STSPEL bit
0
1
0
1
0
SCLi
SDAi
The STPREQ
bit is set to "1"
(start)
Start condition detect
interrupt
i=0 to 4
Figure 16.22 STSPSEL Bit Function
Rev. 1.10 Oct. 18, 2005 Page 195 of 435
REJ09B0162-0110
The STPREQ
bit is set to "1"
(start)
Stop condition detect
interrupt
M32C/88 Group (M32C/88T)
16. Serial I/O (Special Function)
16.3.3 Arbitration
The ABC bit in the UiSMR register (i=0 to 4) determines an update timing for the ABT bit in the UiRB
register. On the rising edge of the SCLi pin, the microcomputer determines whether a transmit data
matches data input to the SDAi pin.
When the ABC bit is set to "0" (update per bit), the ABT bit is set to "1" (detected-arbitration is lost) as
soon as a data discrepancy is detected. The ABT bit is set to "0" (not detected-arbitration is won) if not
detected. When the ABC bit is set to "1" (update per byte), the ABT bit is set to "1" on the falling edge of
the ninth bit of the transfer clock if any discrepancy is detected. When the ABT bit is updated per byte, set
the ABT bit to "0" between an ACK detection in the first byte data and the next byte data to be transferred.
When the ALS bit in the UiSMR2 register is set to "1" (SDA output stop enabled), the arbitration lost
occurs. As soon as the ABT bit is set to "1", the SDAi pin is placed in a high-impedance state.
16.3.4 Transfer Clock
The transfer clock transmits and receives data as is shown in Figure 16.20.
The CSC bit in the UiSMR2 register (i=0 to 4) synchronizes an internally generated clock (internal SCLi)
with the external clock applied to the SCLi pin. When the CSC bit is set to "1" (clock synchronous enabled) and the internal SCLi is held high ("H"), the internal SCLi become low ("L") if signal applied to the
SCLi pin is on the falling edge. Value of the UiBRG register is reloaded to start counting for low level. A
counter stops when the SCLi pin is held "L" and then the internal SCLi changes "L" to "H". Counting is
resumed when the SCLi pin become "H". The transfer clock of UARTi is equivalent to the AND for signals
from the internal SCLi and the SCLi pin.
The transfer clock is synchronized between a half cycle before the falling edge of first bit of the internal
SCLi and the rising edge of the ninth bit. Select the internal clock as the transfer clock while the CSC bit
is set to "1".
The SWC bit in the UiSMR2 register determines whether the SCLi pin is fixed to be an "L" signal output on
the falling edge of the ninth cycle of the transfer clock or not.
When the SCLHI bit in the UiSMR4 register is set to "1" (enabled), a SCLi output stops when a stop
condition is detected (high-impedance).
When the SWC2 bit in the UiSMR2 register is set to "1" (0 output), the SCLi pin focibly outputs an "L" signal
while transmitting and receiving. The fixed "L" signal applied to the SCLi pin is cancelled by setting the
SWC2 bit to "0" (transfer clock) and the transfer clock input to and output from the SCLi pin are provided.
When the CKPH bit in the UiSMR3 register is set to "1" and the SWC9 bit in the UiSMR4 register is set to
"1" (SCL "L" hold enabled), the SCLi pin is fixed to be an "L" signal output on the next falling edge after the
ninth bit of the clock. The fixed "L" signal applied to the SCLi pin is cancelled by setting the SWC9 bit to
"0" (SCL "L" hold disabled).
16.3.5 SDA Output
Values output set in bits 7 to 0 (D7 to D0) in the UiTB register (i=0 to 4) are provided in descending order
from D7. The ninth bit (D8) is ACK or NACK.
Set the default value of SDAi transmit output when the IICM bit is set to "1" (I2C mode) and the SMD2 to
SMD0 bits in the UiMR register are set to "0002" (serial I/O disabled).
The DL2 to DL0 bits in the UiSMR3 register determine no delay in the SDAi output or a delay of 2 to 8
UiBRG register count source cycles.
When the SDHI bit in the UiSMR2 register is set to "1" (SDA output disabled), the SDAi pin is forcibly
placed in a high-impedance state. Do not set the SDHI bit on the rising edge of the UARTi transfer clock.
The ABT bit in the UiRB register may be set to "1" (detected).
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 196 of 435
M32C/88 Group (M32C/88T)
16. Serial I/O (Special Function)
16.3.6 SDA Input
When the IICM2 bit in the UiSMR2 register (i=0 to 4) is set to "0", the first eight bits of received data are
stored into bits 7 to 0 (D7 to D0) in the UiRB register. The ninth bit (D8) is ACK or NACK.
When the IICM2 bit is set to "1", the first seven bits (D7 to D1) of received data are stored into bits 6 to 0
in the UiRB register. Store the eighth bit (D0) into bit 8 in the UiRB register.
If the IICM2 bit is set to "1" and the CKPH bit in the UiSMR3 register is set to "1", the same data as that of
when setting the IICM2 bit to "0" can be read. To read the data, read the UiRB register after the rising
edge of the ninth bit of the transfer clock.
16.3.7 ACK, NACK
When the STSPSEL bit in the UiSMR4 register (i=0 to 4) is set to "0" (serial I/O circuit selected) and the
ACKC bit in the UiSMR4 register is set to "1" (ACK data output), the SDAi pin provides the value output
set in the ACKD bit in the UiSMR4 register.
If the IICM2 bit is set to "0", the NACK interrupt request is generated when the SDAi pin is held high ("H")
on the rising edge of the ninth bit of the transfer clock. The ACK interrupt request is generated when the
SDAi pin is held low ("L") on the rising edge of the ninth bit of the transfer clock.
When ACK is selected to generate a DMA request, the DMA transfer is activated by an ACK detection.
16.3.8 Transmit and Receive Reset
When the STC bit in the UiSMR2 register (i=0 to 4) is set to "1" (UARTi initialization enabled) and a start
condition is detected,
- the transmit shift register is reset and the content of the UiTB register is transferred to the transmit shift
register. The first bit starts transmitting when the next clock is input. UARTi output value remains
unchanged between when the clock is applied and when the first bit data output is provided. The value
remains the same as when start condition was detected.
- the receive shift register is reset and the first bit start receiving when the next clock is applied.
- the SWC bit is set to "1" (SCL wait output enabled). The SCLi pin becomes "L" on the falling edge of the
ninth bit of the transfer clock.
If UARTi transmission and reception are started with this function, the TI bit in the UiC1 register remains
unchanged. Select the external clock as the transfer clock when using this function.
Rev. 1.10 Oct. 18, 2005 Page 197 of 435
REJ09B0162-0110
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
16.4 Special Mode 2
In special
mode 2, serial communication between one or multiple masters and multiple slaves is available.
_____
The SSi input pin (i=0 to 4) controls the serial bus communication. Table 16.19 lists specifications of special
mode 2. Table 16.20 lists register settings. Tables 16.21 to 16.23 list pin settings.
Table 16.19 Special Mode 2 Specifications
Item
Specification
Transfer Data Format
Transfer Clock
Transfer data : 8 bits long
• The CKDIR bit in the UiMR register (i=0 to 4) is set to "0" (internal clock selected):
fj/2(m+1) fj = f1, f8, f2n(1)
m : setting value of the UiBRG register, 0016 to FF16
• The CKDIR bit to "1" (external clock selected) : input from the CLKi pin
______
Transmit/Receive Control SSi input pin function
Transmit Start Condition To start transmitting, the following requirements must be met(2):
- Set the TE bit in the UiC1 register to "1" (transmit enabled)
- Set the TI bit in the UiC1 register to "0" (data in the UiTB register)
Receive Start Condition To start receiving, the following requirement must be met(2):
- Set the RE bit in the UiC1 register to "1" (receive enabled)
- Set the TE bit in the UiC1 register to "1" (transmit enabled)
- Set the TI bit in the UiC1 register to "0" (data in the UiTB register)
Interrupt Request
• While transmitting, the following conditions can be selected:
Generation Timing
- The UiIRS bit in the UiC1 register is set to "0" (no data in a transmit buffer) :
when data is transferred from the UiTB register to the UARTi transmit register (transmission started)
- The UiIRS register is set to "1" (transmission completed):
when data transmission from UARTi transfer register is completed
• While receiving
When data is transferred from the UARTi receive register to the UiRB register (reception completed)
Error Detection
• Overrun error(3)
This error occurs when the seventh bit of the next received data is read before reading
the UiRB register
• Fault error
______
In master mode, the fault error occurs an "L" signal is applied to the SSi pin
Selectable Function
• CLK polarity
Selectable from the rising edge or falling edge of the transfer clock at transferred data
output or input timing
• LSB first or MSB first
Selectable from data transmission or reception in either bit 0 or in bit 7
• Continuous receive mode
Reception is enabled simultaneously by reading the UiRB register
• Serial data logic inverse
This function inverses transmitted or received data logically
• TxD and RxD I/O polarity inverse
TxD pin output and RxD pin input are inversed. All I/O data levels are also inversed
• Clock phase
Selectable from one of 4 combinations of transfer data polarity and phases
_____
• SSi input pin function
Output pin is placed in a high-impedance state to avoid data conflict between master
and other masters or slaves
NOTES:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
2. To start transmission/reception when selecting the external clock, these conditions must be met after the
CKPOL bit in the UiC0 register is set to "0" (data is transmitted on the falling edge of the transfer clock and data
is received on the rising edge) and the CLKi pin is held high ("H"), or when the CKPOL bit is set to "1" (Data is
transmitted on the rising edge of the transfer clock and data is received on the falling edge) and the CLKi pin is
held low ("L").
3. If an overrun error occurs, the UiRB register is in an indeterminate state. The IR bit setting in the SiRIC register
does not change to "1" (interrupt requested).
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 198 of 435
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.20 Register Settings in Special Mode 2
Register
Bit
Function
UiTB
7 to 0
Set transmit data
UiRB
7 to 0
Received data can be read
OER
Overrun error flag
UiBRG
7 to 0
Set bit rate
UiMR
UiC0
SMD2 to SMD0
Set to "0012"
CKDIR
Set to "0" in master mode or "1" in slave mode
IOPOL
Set to "0"
CLK1, CLK0
Select count source for the UiBRG register
CRS
Disabled because the CRD bit is set to "1"
TXEPT
Transfer register empty flag
CRD
Set to "1"
NCH
Select the output format of the TxDi pin
CKPOL
Clock phase can be set by the combination of the CKPOL bit and the CKPH bit in
the UiSMR3 register
UiC1
UFORM
Select either LSB first or MSB first
TE
Set to "1" to enable data transmission and reception
TI
Transfer buffer empty flag
RE
Set to "1" to enable data reception
RI
Reception complete flag
UiIRS
Select what causes the UARTi transmit interrupt to be generated
UiRRM
Set to "1" to enable continuous receive mode
UiLCH, SCLKSTPB Set to "0"
UiSMR
7 to 0
Set to "0016"
UiSMR2
7 to 0
Set to "0016"
SSE
Set to "1"
CKPH
Clock phase can be set by the combination of the CKPH bit and the CKPOL bit
UiSMR3
in the UiC0 register
DINC
UiSMR4
Set to "0" in master mode or "1" in slave mode
NODC
Set to "0"
ERR
Fault error flag
7 to 5
Set to "0002"
7 to 0
Set to "0016"
i=0 to 4
Rev. 1.10 Oct. 18, 2005 Page 199 of 435
REJ09B0162-0110
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.21 Pin Settings in Special Mode 2 (1)
Port
Function
______
P60
P61
SS0 input
CLK0 input (slave)
CLK0 output (master)
RxD0 input (master)
STxD0 output (slave)
TxD0 output (master)
SRxD0 input (slave)
______
SS1 input
CLK1 input (slave)
CLK1 output (master)
RxD1 input (master)
STxD1 output (slave)
TxD1 output (master)
SRxD1 input (slave)
P62
P63
P64
P65
P66
P67
PS0 Register
PS0_0=0
PS0_1=0
PS0_1=1
PS0_2=0
PS0_2=1
PS0_3=1
PS0_3=0
PS0_4=0
PS0_5=0
PS0_5=1
PS0_6=0
PS0_6=1
PS0_7=1
PS0_7=0
Setting
PSL0 Register
–
–
–
–
PSL0_2=1
–
–
–
–
–
–
PSL0_6=1
–
–
PS1 Register
PS1_0=1
PS1_0=0
PS1_1=0
PS1_1=1
PS1_2=0
PS1_2=1
PS1_3=0
Setting
PSL1 Register
PSC Register
PSL1_0=0
PSC_0=0
–
–
–
–
PSL1_1=1
PSC_1=0
–
–
PSL1_2=0
PSC_2=0
–
–
PD7 Register
–
PD7_0=0
PD7_1=0
–
PD7_2=0
–
PD7_3=0
PS3 Register(1)
PS3_0=0
PS3_0=1
PS3_1=0
PS3_1=1
PS3_2=1
PS3_2=0
PS3_3=0
PS3_4=0
PS3_5=0
PS3_5=1
PS3_6=1
PS3_6=0
PS3_7=0
PS3_7=1
Setting
PSL3 Register
–
–
–
PSL3_1=1
PSL3_2=0
–
PSL3_3=0
PSL3_4=0
PSL3_5=0
–
–
PSL3_6=0
–
PSL3_7=1
PD9 Register(1)
PD9_0=0
–
PD9_1=0
–
–
PD9_2=0
PD9_3=0
PD9_4=0
PD9_5=0
–
–
PD9_6=0
PD9_7=0
–
PD6 Register
PD6_0=0
PD6_1=0
–
PD6_2=0
–
–
PD6_3=0
PD6_4=0
PD6_5=0
–
PD6_6=0
–
–
PD6_7=0
Table 16.22 Pin Settings (2)
Port
P70(1)
P71(1)
P72
Function
TxD2 output (master)
SRxD2 input (slave)
RxD2 input (master)
STxD2 output (slave)
CLK2 input (slave)
CLK2 output (master)
______
SS2 input
P73
NOTE:
1. P70 and P71 are ports for the N-channel open drain output.
Table 16.23 Pin Settings (3)
Port
P90
P91
P92
P93
P94
P95
P96
P97
Function
CLK3 input (slave)
CLK3 output (master)
RxD3 input (master)
STxD3 output (slave)
TxD3 output (master)
SRxD3 input (slave)
______
SS3 input
_______
SS4 input
CLK4 input (slave)
CLK4 output (master)
TxD4 output (master)
SRxD4 input (slave)
RxD4 input (master)
STxD4 output (slave)
PSC3 Register
–
–
–
–
–
–
–
–
–
–
PSC3_6=0
–
–
–
NOTE:
1. Set the PD9 and PS3 registers immediately after the PRC2 bit in the PRCR register is set to "1" (write enabled). Do
not generate an interrupt or a DMA transfer between the instruction to set to the PRC2 bit to "1" and the instruction to
set the PD9 and PS3 registers.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 200 of 435
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
______
16.4.1 SSi Input Pin Function (i=0 to 4)
____
When the SSE bit in the UiSMR3 register is set to "1" (SS function enabled), the special mode 2 is
selected, activating the pin function.
The DINC bit in the UiSMR3 register determines which microcomputer performs as master or slave.
______
When multiple microcomputers perform as the masters (multi-master system), the SSi pin setting determines which master microcomputer is active and when.
16.4.1.1 When Setting the DINC Bit to "1" (Slave Mode)
_____
When a high-level ("H") signal is applied to the SSi pin, the STxDi and SRxDi pins are placed in a highimpedance state and the transfer clock applied to the CLKi pin is ignored. When a low-level ("L") signal
_____
is applied to the SSi input pin, the transfer clock input is valid and serial communication is enabled.
16.4.1.2 When Setting the DINC Bit to "0" (Master Mode)
______
When using the SSi pin functin in master mode, set the UiIRS bit in the UiC1 register to "1" (transmission completed).
_____
When an "H" signal is applied to the SSi pin, serial communication is available due to transmission
_____
privilege. The master provides the transfer clock output. When an "L" signal is applied to the SSi pin,
it indicates that another master is active. The TxDi and CLKi pins are placed in high-impedance states
and the ERR bit in the UiSMR3 register is set to "1" (fault error) Use the transmit complete interrupt
routine to verify the ERR bit state.
To resume the serial communication after the fault error occurs, set the ERR bit to "0" while applying
______
the "H" signal to the SSi pin. The TxDi and CLKi pins become ready for signal outputs.
Microcomputer
Microcomputer
P13
P12
P93(SS3)
P93(SS3)
P90(CLK3)
P90(CLK3)
P91(RxD3)
P91(STxD3)
P92(TxD3)
P92(SRxD3)
Master
Slave
Microcomputer
P93(SS3)
P90(CLK3)
P91(STxD3)
P92(SRxD3)
Slave
____
Figure 16.23 Serial Bus Communication Control with SS Pin
Rev. 1.10 Oct. 18, 2005 Page 201 of 435
REJ09B0162-0110
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
16.4.2 Clock Phase Setting Function
The CKPH bit in the UiSMR3 register (i=0 to 4) and the CKPOL bit in the UiC0 register select one of four
combinations of transfer clock polarity and phases.
The transfer clock phase and polarity must be the same between the master and the slave involved in the
transfer.
16.4.2.1 When setting the DINC Bit to "0" (Master (Internal Clock))
Figure 16.24 shows transmit and receive timing.
16.4.2.2 When Setting the DINC Bit to "1" (Slave (External Clock))
_____
When the CKPH bit is set to "0" (no clock delay) and the SSi input pin is held high ("H"), the STxDi pin
_____
is placed in a high-impedance state. When the SSi input pin becomes low ("L"), conditions to start a
serial transfer are met, but output is indeterminate. The serial transmission is synchronized with the
transfer clock. Figure 16.25 shows the transmit and receive timing.
_____
When the CKPH bit is set to "1" (clock delay) and the SSi input pin is held high, the STxDi pin is placed
_____
in a high-impedance state. When the SSi pin becomes low, the first data is output. The serial transmission is synchronized with the transfer clock. Figure 16.26 shows the transmit and receive timing.
Signal Applied to
the SS Pin
"H"
"L"
Clock Output
"H"
(CKPOL=0, CKPH=0) "L"
Clock Output
"H"
(CKPOL=1, CKPH=0) "L"
Clock Output
"H"
(CKPOL=0, CKPH=1) "L"
Clock Output
"H"
(CKPOL=1, CKPH=1) "L"
Data Output Timing
"H"
"L"
D0
D1
D2
D3
D4
D5
Data Input Timing
Figure 16.24 Transmit and Receive Timing in Master Mode (Internal Clock)
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 202 of 435
D6
D7
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Signal Applied to
the SS Pin
"H"
"L"
"H"
Clock Input
(CKPOL=0, CKPH=0) "L"
"H"
Clock Input
(CKPOL=1, CKPH=0) "L"
Data Output Timing(1)
"H"
"L"
Data Input Timing
D0
D1
D2
D3
D4
D5
D6
D7
Highimpedance
Highimpedance
Indeterminate
NOTE:
1. P70 and P71 are ports for the N-channel open drain output and must be pulled up externally
for data output.
Figure 16.25 Transmit and Receive Timing in Slave Mode (External Clock) (CKPH=0)
"H"
Signal Applied to
the SS Pin
"L"
"H"
Clock Input
(CKPOL=0, CKPH=0) "L"
"H"
Clock Input
(CKPOL=1, CKPH=1) "L"
Data Output Timing(1) "H"
"L"
D0
D1
D2
D3
D4
D5
D6
D7
Highimpedance
Data Input Timing
NOTE:
1. P70 and P71 are ports for the N-channel open drain output and must be pulled up externally
for data output.
Figure 16.26 Transmit and Receive Timing in Slave Mode (External Clock) (CKPH=1)
Rev. 1.10 Oct. 18, 2005 Page 203 of 435
REJ09B0162-0110
Highimpedance
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
16.5 Special Mode 3 (GCI Mode)
In GCI mode, the external clock is synchronized with the transfer clock used in the clock synchronous serial
I/O mode.
Table 16.24 lists specifications of GCI mode. Table 16.25 lists registers settings. Tables 16.26 to 16.28 list
pin settings.
Table16.24 GCI Mode Specifications
Item
Specification
Transfer Data Format
Transfer data : 8 bits long
Transfer Clock
The CKDIR bit in the UiMR register (i=0 to 4) is set to "1" (external clock selected):
input from the CLKi pin
________
Clock Synchronization Function Trigger signal input from the CTSi pin
Transmit/Receive Start
To start data transmission and reception, meet the following conditions and then apply a
Condition
trigger signal to the CTSi pin:
________
- Set the TE bit in the UiC1 register to "1" (transmit enabled)
- Set the RE bit in the UiC1 register to "1" (receive enabled)
- Set the TI bit in the UiC1 register to "0" (Data in the UiTB register)
Interrupt Request
• While transmitting, the following condition can be selected:
Generation Timing
- The UiIRS bit in the UiC1 register is set to "0" (UiTB register empty):
when data is transferred from the UiTB register to the UARTi transmit register (transmission started)
- The UiIRS bit is set to "1" (Transmit completed):
when a data transmission from the UARTi transfer register is completed
• While receiving,
when data is transferred from the UARTi receive register to the UiRB register (reception
completed)
Error Detection
Overrun error(1)
This error occurs when the seventh bit of the next received data is read before reading the
UiRB register.
NOTE:
1. If an overrun error occurs, the UiRB register is indeterminate. The IR bit setting in the SiRIC register does not
change to "1" (interrupt requested).
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 204 of 435
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.25 Register Settings in GCI Mode
Register
Bit
Function
UiTB
7 to 0
Set transmit data
UiRB
7 to 0
Received data
OER
Overrun error flag
UiBRG
7 to 0
Set to "0016"
UiMR
UiC0
UiC1
UiSMR
UiSMR2
UiSMR3
UiSMR4
SMD2 to SMD0
Set to "0012"
CKDIR
Set to "1"
IOPOL
Set to "0"
CLK1, CLK0
Set to "002"
CRS
Disabled because the CRD bit is set to "1"
TXEPT
Transfer register empty flag
CRD
Set to "1"
NCH
Select the output format of the TxDi pin
CKPOL
Set to "0"
UFORM
Set to "0"
TE
Set to "1" to enable data transmission and reception
TI
Transfer buffer empty flag
RE
Set to "1" to enable data reception
RI
Reception complete flag
UiIRS
Select what causes the UARTi transmit interrupt to be generated
UiRRM, UiLCH
Set to "0"
SCLKSTPB
Set to "0"
6 to 0
Set to "00000002"
SCLKDIV
See Table 16.29
6 to 0
Set to "00000002"
SU1HIM
See Table 16.29
2 to 0
Set to "0002"
NODC
Set to "0"
7 to 4
Set to "00002"
7 to 0
Set to "0016"
i=0 to 4
Rev. 1.10 Oct. 18, 2005 Page 205 of 435
REJ09B0162-0110
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.26 Pin Settings in GCI Mode (1)
Port
Function
Setting
PS0 Register
PD6 Register
P60
CTS0 input(1)
PS0_0=0
PD6_0=0
P61
CLK0 input
PS0_1=0
PD6_1=0
P62
RxD0 input
PS0_2=0
PD6_2=0
TxD0 output
__________
P63
PS0_3=1
–
P64
CTS1 input(1)
PS0_4=0
PD6_4=0
P65
CLK1 input
PS0_5=0
PD6_5=0
P66
RxD1 input
PS0_6=0
PD6_6=0
P67
TxD1 output
PS0_7=1
–
__________
NOTE:
_______
1. CTS input is used as a trigger siganl input.
Table 16.27 Pin Settings (2)
Port
Function
Setting
PS1 Register
PSL1 Register
PSC Register
PD7 Register
P70(1)
TxD2 output
PS1_0=1
PSL1_0=0
PSC_0=0
–
P71(1)
RxD2 input
PS1_1=0
–
–
PD7_1=0
CLK2 input
PS1_2=0
–
–
PD7_2=0
PS1_3=0
–
–
PD7_3=0
P72
__________
CTS2 input(2)
P73
NOTES:
1. P70 and P71 are ports for the N-channel open drain output.
_______
2. CTS input is used as a trigger siganl input.
Table 16.28 Pin Settings (3)
Port
Function
Setting
PS3 Register(1)
PSL3 Register
PSL3 Register
PD9 Register(1)
P90
CLK3 input
PS3_0=0
–
–
PD9_0=0
P91
RxD3 input
PS3_1=0
–
–
PD9_1=0
TxD3 output
PS3_2=1
PSL3_2=0
–
–
PS3_3=0
PSL3_3=0
–
PD9_3=0
PS3_4=0
PSL3_4=0
–
PD9_4=0
PS3_5=0
PSL3_5=0
–
PD9_5=0
P92
__________
P93
CTS3 input(2)
__________
input(2)
P94
CTS4
P95
CLK4 input
P96
TxD4 output
PS3_6=1
PSL3_6=0
PSL3_6=0
–
P97
RxD4 input
PS3_7=0
–
–
PD9_7=0
NOTES:
1. Set the PD9 and PS3 registers immediately after the PRC2 bit in the PRCR register is set to "1" (write enabled). Do
not generate an interrupt or a DMA transfer between the instruction to set to the PRC2 bit to "1" and the instruction to
set the PD9 and PS3 registers.
_______
2. CTS input is used for a trigger siganl input.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 206 of 435
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
To generate the internal clock synchronized with the external clock, set the SU1HIM bit in the UiSMR2
register (i=0 to 4) and the SCLKDIV bit in the UiSMR register to values shown in Table 16.29. Then apply
________
a trigger signal to the CTSi pin. Either the same clock cycle as the external clock or external clock divided
by two can be selected as the transfer clock. The SCLKSTPB bit in the UiC1 register controls the transfer
clock. Set the SCLKSTPB bit accordingly, to start or stop the transfer clock during an external clock
operation. Figure 16.27 shows an example of the clock-divided synchronous function.
Table 16.29 Clock-Divided Synchronous Function Select
SCLKDIV Bit in
SU1HIM Bit in
Clock-Divided Synchronous Function
UiSMR Register
UiSMR2 Register
Example of Waveform
0
0
Not synchronized
-
0
1
Same division as the external clock
A in Figure 16.27
1
0 or 1
Same division as the external clock
B in Figure 16.27
divided by 2
i=0 to 4
External Clock
from the CLKi Pin
Trigger Signal
from the CTSi Pin
1
2
3
4
5
6
7
8
Transfer Clock
The SCLKSTPB bit in the UiC1 register
stops transfer clock
A
TxDi
1
2
3
4
5
6
7
8
Transfer Clock
B
TxDi
1
2
3
i=0 to 4
A, B: See Table 16.29.
Figure 16.27 Clock-Divided Synchronous Function
Rev. 1.10 Oct. 18, 2005 Page 207 of 435
REJ09B0162-0110
4
5
6
7
8
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
16.6 Special Mode 4 (IE Mode)
In IE mode, devices connected with the IEBus can communicate in UART mode.
Table 16.30 lists register settings. Tables 16.31 to 16.33 list pin settings.
Table 16.30 Register Settings in IE Mode
Register
Bit
Function
UiTB
8 to 0
Set transmit data
UiRB
8 to 0
Received data can be read
OER, FER,
Error flags
PER, SUM
UiBRG
7 to 0
Set bit rate
UiMR
SMD2 to SMD0
Set to "1102"
CKDIR
Select the internal clock or external clock
STPS
Set to "0"
PRY
Disabled because the PRYE bit is set to "0"
PRYE
Set to "0"
UiC0
UiC1
IOPOL
Select TxD and RxD I/O polarity
CLK1, CLK0
Select count source for the UiBRG register
CRS
Disabled because the CRD bit is set to "1"
TXEPT
Transfer register empty flag
CRD
Set to "1"
NCH
Select output format of the TxDi pin
CKPOL
Set to "0"
UFORM
Set to "0"
TE
Set to "1" to enable data transmission
TI
Transfer buffer empty flag
RE
Set to "1" te enable data reception
RI
Reception complete flag
UiIRS
Select what causes the UARTi transmit interrupt to be generated
UiRRM, UiLCH,
Set to "0"
SCLKSTPB
UiSMR
3 to 0
Set to "00002"
ABSCS
Select bus conflict detect sampling timing
ACSE
Set to "1" to automatically clear the transmit enable bit
SSS
Select transmit start condition
SCLKDIV
Set to "0"
UiSMR2
7 to 0
Set to "0016"
UiSMR3
7 to 0
Set to "0016"
UiSMR4
7 to 0
Set to "0016"
IFSR
IFSR6, IFSR7
Select how the bus conflict interrupt occurs
i=0 to 4
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 208 of 435
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.31 Pin Settings in IE Mode (1)
Port
Function
Setting
PS0 Register
P61
PD6 Register
CLK0 input
PS0_1=0
PD6_1=0
CLK0 output
PS0_1=1
–
P62
RxD0 input
PS0_2=0
PD6_2=0
P63
TxD0 output
PS0_3=1
–
P65
CLK1 input
PS0_5=0
PD6_5=0
CLK1 output
PS0_5=1
–
P66
RxD1 input
PS0_6=0
PD6_6=0
P67
TxD1 output
PS0_7=1
–
Table 16.32 Pin Settings (2)
Port
Function
Setting
PS1 Register
P70(1)
TxD2 output
P71(1)
P72
PSL1 Register
PSC Register
PD7 Register
PS1_0=1
PSL1_0=0
PSC_0=0
–
RxD2 input
PS1_1=0
–
–
PD7_1=0
CLK2 input
PS1_2=0
–
–
PD7_2=0
CLK2 output
PS1_2=1
PSL1_2=0
PSC_2=0
–
NOTE:
1. P70 and P71 are ports for the N-channel open drain output.
Table 16.33 Pin Settings (3)
Port
Function
Setting
PS3
P90
Register(1)
PSL3 Register
PSC3 Register
PD9 Register(1)
CLK3 input
PS3_0=0
–
–
PD9_0=0
CLK3 output
PS3_0=1
–
–
–
P91
RxD3 input
PS3_1=0
–
–
PD9_1=0
P92
TxD3 output
PS3_2=1
PSL3_2=0
–
–
P95
CLK4 input
PS3_5=0
PSL3_5=0
–
PD9_5=0
CLK4 output
PS3_5=1
–
–
–
P96
TxD4 output
PS3_6=1
–
PSC3_6=0
–
P97
RxD4 input
PS3_7=0
–
–
PD9_7=0
NOTE:
1. Set the PD9 and PS3 registers immediately after the PRC2 bit in the PRCR register is set to "1" (write enabled).
Do not generate an interrupt or a DMA transfer between the instruction to set to the PRC2 bit to "1" and the instruction
to set the PD9 and PS3 registers.
Rev. 1.10 Oct. 18, 2005 Page 209 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
16. Serial I/O (Special Function)
If the output signal level of the TxDi pin (i=0 to 4) differs from the input signal level of the RxDi pin, an
interrupt request is generated.
UART0 and UART3 are assigned software interrupt number 40. UART1 and UART4 are assigned number
41. When using the bus conflict detect function of UART0 or UART3, of UART1 or UART4, set the IFSR6
bit and the IFSR7 bit in the IFSR register accordingly.
When the ABSCS bit in the UiSMR register is set to "0" (rising edge of the transfer clock), it is determined,
on the rising edge of the transfer clock, if the output level of the TxD pin and the input level of the RxD pin
match. When the ABSCS bit is set to "1" (timer Aj underflow), it is determined when the timer Aj (timer A3
in UART0, timer A4 in UART1, timer A0 in UART2, timer A3 in UART3, the timer A4 in UART4) counter
overflows. Use the timer Aj in one-shot timer mode.
When the ACSE bit in the UiSMR register is set to "1" (automatic clear at bus conflict) and the IR bit in the
BCNiIC register to "1" (discrepancy detected), the TE bit in the UiC1 register is set to "0" (transmit disable).
When the SSS bit in the UiSMR register is set to "1" (synchronized with RxDi), data is transmitted from the
TxDi pin on the falling edge of the RxDi pin. Figure 16.28 shows bits associated with the bus conflict detect
function.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 210 of 435
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
(1) The ABSCS Bit in the UiSMR Register (Bus conflict and sampling clock selected)
(i=0 to 4)
Bus conflict is detected on the rising edge of the transfer clock
when the ABSCS bit is set to "0"
Transfer Clock
ST
D0
D1
D2
D3
D4
D5
D6
D7
D8
SP
TxDi
RxDi
Trigger signal is applied to the TAjIN pin
Timer Aj
When the ABSCS bit is set to "1", bus conflict is detected when the timer Aj
underflows (in the one-shot timer mode). An interrupt request is generated.
Timer Aj: timer A3 in UART0 or UART3, timer A4 in UART1 or UART4, timer A0 in UART2
(2) The ACSE Bit in the UiSMR Register (Transmit enable bit is automatically cleared)
Transfer Clock
ST
D0
D1
D2
D3
D4
D5
D6
D7
D8
SP
TxDi
RxDi
IR bit in
BCNilC register
TE bit in
UiC1 register
(3) The SSS bit in the UiSMR Register (Transmit start condition is selected)
When the SSS bit is set to "0", data is transmitted after one transfer clock cycle
if data transmission is enabled.
Transfer Clock
ST
D0
D1
D2
D3
D4
D5
D6
D7
D8
SP
D7
D8
SP
TxDi
transmit enable conditons are met
When the SSS bit is set to "1", data is transmitted on the falling edge of RxDi(1)
CLKi
ST
TxDi
D0
D1
D2
D3
D4
D5
D6
(Note 2)
RxDi
NOTES:
1. Data is transmitted on the falling edge of a signal applied to the RxDi pin when the IOPOL bit is set to "0".
Data is transmitted on the rising edge of a signal applied to the RxDi pin when the IOPOL bit is set to "1".
2. Data transmission condition must be met before the falling edge of the RxDi pin.
Figure 16.28 Bit Function Related Bus Conflict Detection
Rev. 1.10 Oct. 18, 2005 Page 211 of 435
REJ09B0162-0110
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
16.7 Special Mode 5 (SIM Mode)
In SIM mode, SIM interface devices can communicate in UART mode. Both direct and inverse formats are
available and a low-level ("L") signal output can be provided from the TxDi pin (i=0 to 4) when a parity error
is detected.
Table 16.34 lists specifications of SIM mode. Table 16.35 lists register settings. Tables 16.36 to 16.38 list
pin settings.
Table 16.34 SIM Mode Specifications
Item
Transfer Data Format
Transfer Clock
Specification
• Transfer data: 8-bit UART mode
• One stop bit
• In direct format
• In inverse format
Parity:
Even
Parity:
Odd
Data logic:
Direct
Data logic:
Inverse
Transfer format:
LSB first
Transfer format:
MSB first
• The CKDIR bit in the UiMR register (i=0 to 4) is "0" (internal clock selected):
fj/16(m+1)(1) fj = f1, f8, f2n(2) m : setting value of the UiBRG register, 0016 to FF16
Do not set the CKDIR bit to "1" (external clock selected)
_______
_______
Transmit/Receive Control The CRD bit in the UiC0 register is set to "1" (CTS, RTS function disabled)
Other Setting Items
The UiIRS bit in the UiC1 register is set to "1" (transmission completed)
Transmit Start Condition To start transmitting, the following requirements must be met:
- Set the TE bit in the UiC1 register to "1" (transmit enabled)
- Set the TI bit in the UiC1 register to "0" (data in the UiTB register)
Receive Start Condition To start receiving, the following requirements must be met:
- Set the RE bit in the UiC1 register to "1" (receive enabled)
- Detect the start bit
Interrupt Request
Generation Timing
• While transmitting,
-The UiIRS bit is set to "1" (transmission completed):
when data transmission from the UARTi transfer register is completed
• While receiving,
when data is transferred from the UARTi receive register to the UiRB register (reception completed)
Error Detection
• Overrun error(1)
This error occurs when the eighth bit of the next data is received before reading the
UiRB register
• Framing error
This error occurs when the number of the stop bit set is not detected
• Parity error
This error occurs when the number of "1" in parity bit and character bits differs from
the number set
• Error sum flag
The SUM bit is set to "1" when an overrun error, framing error or parity error occurs
NOTES:
1. If an overrun error occurs, the UiRB register is indeterminate. The IR bit setting in the SiRIC register does not
change to "1" (interrupt requested).
2. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 212 of 435
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.35 Register Settings in SIM Mode
Register
UiTB
UiRB
Bit
Function
7 to 0
Set transmit data
7 to 0
Received data can be read
OER, FER,
Error flags
PER, SUM
UiBRG
UiMR
UiC0
UiC1
7 to 0
Set bit rate
SMD2 to SMD0
Set to "1012"
CKDIR
Set to "0"
STPS
Set to "0"
PRY
Set to "1" for direct format or "0" for inverse format
PRYE
Set to "1"
IOPOL
Set to "0"
CLK1, CLK0
Select count source for the UiBRG register
CRS
Disabled because the CRD bit is set to "1"
TXEPT
Transfer register empty flag
CRD
Set to "1"
NCH
Set to "1"
CKPOL
Set to "0"
UFORM
Set to "0" for direct format or "1" for inverse format
TE
Set to "1" to enable data transmission
TI
Transfer buffer empty flag
RE
Set to "1" to enable data reception
RI
Reception complete flag
UiIRS
Set to "1"
UiRRM
Set to "0"
UiLCH
Set to "0" for direct format or "1" for inverse format
UiERE
Set to "1"
UiSMR
7 to 0
Set to "0016"
UiSMR2
7 to 0
Set to "0016"
UiSMR3
7 to 0
Set to "0016"
UiSMR4
7 to 0
Set to "0016"
i=0 to 4
Rev. 1.10 Oct. 18, 2005 Page 213 of 435
REJ09B0162-0110
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Table 16.36 Pin Settings in SIM Mode (1)
Port
Function
Setting
PS0 Register
PD6 Register
P62
RxD0 input
PS0_2=0
PD6_2=0
P63
TxD0 output
PS0_3=1
–
P66
RxD1 input
PS0_6=0
PD6_6=0
P67
TxD1 output
PS0_7=1
–
PS1 Register
PSL1 Register
PSC Register
Table 16.37 Pin Settings (2)
Port
Function
Setting
PD7 Register
P70(1)
TxD2 output
PS1_0=1
PSL1_0=0
PSC_0=0
–
P71(1)
RxD2 input
PS1_1=0
–
–
PD7_1=0
PSC3 Register
PD9 Register(1)
NOTE:
1. P70 and P71 are ports for the N-channel open drain output.
Table 16.38 Pin Settings (3)
Port
Function
Setting
PS3
Register(1)
PS3_1=0
PSL3 Register
P91
RxD3 input
–
P92
TxD3 output
PS3_2=1
PSL3_2=0
P96
TxD4 output
PS3_6=1
–
P97
RxD4 input
PS3_7=0
–
PD9_1=0
–
PSC3_6=0
–
PD9_7=0
NOTE:
1. Set the PD9 and PS3 registers immediately after the PRC2 bit in the PRCR register is set to "1" (write enabled).
Do not generate an interrupt or a DMA transfer between the instruction to set to the PRC2 bit to "1" and the instruction
to set the PD9 and PS3 registers.
Figure 16.29 shows an example of a SIM interface operation. Figure 16.30 shows an example of a SIM
interface connection. Connect the TxDi pin to the RxDi pin for a pull-up.
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 214 of 435
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
(1) Transmit Timing
Tc
Transfer Clock
TE bit in the UiC1
register
TI bit in the UiC1
register
"1"
Data is written to
the UiTB register
"0"
(Note 1)
"1"
"0"
Data is transferred from the UiTB
register to the UARTi transmit register
Parity Stop
bit
bit
Start
bit
TxDi
ST D0 D1
D2 D3 D4 D5 D6 D7
P
ST D0 D1 D2 D3 D4 D5 D6 D7
SP
Parity Error Signal
returned from
Receiving End
SP
An "L" signal is applied from the SIM
card due to a parity error
Signal Line Level(2)
TXEPT bit in the
UiC0 register
P
ST D0 D1 D2 D3 D4 D5 D6 D7
P
ST D0 D1 D2 D3 D4 D5 D6 D7
SP
An interrupt routine
detects "H" or "L"
"1"
SP
P
An interrupt routine detects
"H" or "L"
"0"
IR bit in the SiTIC
register
"1"
"0"
Set to "0" by an interrupt request acknowledgement or by program
i=0 to 4
The above applies under the following conditions:
• The PRYE bit in the UiMR register is set to "1" (parity enabled)
• The STPS bit in the UiMR register is set to "0" (1 stop bit)
• The UiIRS bit in the UiC1 register is set to "1" (interrupt request generated
when transmission completed)
Tc = 16(m+1) / fj
fj: count source frequency of the UiBRG register (f1, f8, f2n(4))
m: setting value of the UiBRG register
(2) Receive Timing
Transfer Clock
RE bit in the UiC1
register
"1"
"0"
Start
bit
Transmit Waveform
from the
Transmitting End
ST D0 D1 D2 D3 D4 D5 D6 D7
Parity Stop
bit
bit
P SP
TxDi
ST D0 D1 D2 D3 D4 D5 D6 D7
P
SP
TxDi outputs "L" due to
a parity error
Signal Line Level(3)
ST D0 D1 D2 D3 D4 D5 D6 D7
RI bit in the UiC1
register
"1"
IR bit in the
SiRIC register
"1"
P SP
ST D0 D1 D2 D3 D4 D5 D6 D7
P
SP
"0"
Read the UiRB register
"0"
Set to "0" by an interrupt request acknowledgement or by program
i=0 to 4
The above applies under the following conditions:
• The PRYE bit in the UiMR register is set to "1" (parity enabled)
• The STPS bit in the UiMR register is set to "0" (1 stop bit)
Tc = 16(m+1) / fj
fj: count source frequency of the UiBRG register (f1, f8, f2n(4))
m: setting value of the UiBRG register
NOTES:
1. Data transmission starts when BRG overflows after a value is set to the UiTB register on the rising edge of the TI bit.
2. Because the TxDi and RxDi pins are connected, a composite waveform, consisting of transmit waveform from the TxDi
pin and parity error signal from the receiving end, is generated.
3. Because the TxDi and RxDi pins are connected, a composite waveform, consisting of transmit waveform from the
transmitting end and parity error signal from the TxDi pin, is generated.
4. The CNT3 to CNT0 bits in the TCSPR register selects no division (n=0) or divide-by-2n (n=1 to 15).
Figure 16.29 SIM Interface Operation
Rev. 1.10 Oct. 18, 2005 Page 215 of 435
REJ09B0162-0110
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
Microcomputer
SIM card
TxDi
RxDi
i=0 to 4
Figure 16.30 SIM Interface Connection
16.7.1 Parity Error Signal
16.7.1.1 Parity Error Signal Output Function
When the UiERE bit in the UiC1 register (i=0 to 4) is set to "1" (output), the parity error signal output
can be provided. The parity error signal output is provided when a parity error is detected upon
receiving data. A low-level ("L") signal output is provided from the TxDi pin in the timing shown in
Figure 16.31. When reading the UiRB register during a parity error output, the PER bit in the UiRB
register is set to "0" (no error occurs) and a high-level ("H") signal output is again provided simultaneously.
16.7.1.2 Parity Error Signal
To determine whether the parity error signal is output, the port that shares a pin with the RxDi pin is
read by using an end-of-transmit interrupt routine.
Transfer Clock
"H"
"L"
RxDi
"H"
ST
D0
D1
D2
D3
D4
D5
D6
D7
P
SP
"L"
TxDi
"H"
Hi-Z
"L"
Recieve
Complete Flag
"1"
"0"
NOTE:
1. The above applies to the direct format.
(The PRY bit is set to "1", the UFORM bit is set to "0",
and the UiLCH bit is set to "0").
Figure 16.31 Parity Error Signal Output Timing (LSB First)
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 216 of 435
ST : Start bit
P : Even parity
SP : Stop bit
i=0 to 4
16. Serial I/O (Special Function)
M32C/88 Group (M32C/88T)
16.7.2 Format
16.7.2.1 Direct Format
Set the PRYE bit in the UiMR register (i=0 to 4) to "1" (parity enabled), the PRY bit to "1" (even
parity), the UFORM bit in the UiC0 register to "0" (LSB first) and the UiLCH bit in the UiC1 register to
"0" (not inversed). When data are transmitted, data set in the UiTB register are transmitted with the
even-numbered parity, starting from D0. When data are received, received data are stored in the
UiRB register, starting from D0. The even-numbered parity determines whether a parity error occurs.
16.7.2.2 Inverse Format
Set the PRYE bit to "1", the PRY bit to "0" (odd parity), the UFORM bit to "1" (MSB first) and the
UiLCH bit to "1" (inversed). When data are transmitted, values set in the UiTB register are logically
inversed and are transmitted with the odd-numbered parity, starting from D7. When data are received, received data are logically inversed to be stored in the UiRB register, starting from D7. The
odd-numbered parity determines whether a parity error occurs.
(1) Direct Format
Transfer Clock
"H"
"L"
TxDi
"H"
D0
D1
D2
D3
D4
D5
D6
D7
D7
D6
D5
D4
D3
D2
D1
D0
"L"
P
P : Even parity
(2) Inverse Format
Transfer Clock
TxDi
"H"
"L"
"H"
"L"
P
P : Odd parity
i=0 to 4
Figure 16.32 SIM Interface Format
Rev. 1.10 Oct. 18, 2005 Page 217 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
17. A/D Converter
17. A/D Converter
The A/D converter consists of one 10-bit successive approximation A/D converter with a capacitive coupling amplifier.
The result of an A/D conversion is stored into the A/D registers corresponding to selected pins. It is stored
into the AD00 register only when DMAC operating mode is entered.
Table 17.1 lists specifications of the A/D converter. Figure 17.1 shows a block diagram of the
A/D converter. Figures 17.2 to 17.6 show registers associated with the A/D converter.
NOTE
This section is described in the 144-pin package only as an example.
The AN150 to AN157 pins are not included in the 100-pin package.
Rev. 1.10 Oct. 18, 2005 Page 218 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
Table 17.1 A/D Converter Specifications
Item
A/D Conversion Method
Analog Input
Voltage(1)
Specification
Successive approximation (with a capacitive coupling amplifier)
0V to AVCC (VCC)
Operating Clock, ØAD(2)
fAD, fAD/2, fAD/3, fAD/4, fAD/6, fAD/8
Resolution
8 bits or 10 bits
Operating Mode
One-shot mode, repeat mode, single sweep mode, repeat sweep mode 0,
repeat sweep mode 1, multi-port single sweep mode, multi-port repeat sweep
mode 0
Analog Input
Pins(3)
34 pins
8 pins each for AN (AN0 to AN7), AN0 (AN00 to AN07), AN2 (AN20 to AN27),
AN15 (AN150 to AN157)
2 extended input pins (ANEX0 and ANEX1)
A/D Conversion Start Condition
• Software trigger
The ADST bit in the AD0CON0 register is set to "1" (A/D conversion started) by
program
• External trigger (re-trigger is enabled)
__________
When a falling edge is applied to the AD TRG pin after the ADST bit is set to "1" by
program
• Hardware trigger (re-trigger is enabled)
The timer B2 interrupt request of the three-phase motor control timer functions
(after the ICTB2 counter completes counting) is generated after the ADST bit is
set to "1" by program
Conversion Rate Per Pin
• Without the sample and hold function
8-bit resolution : 49 ØAD cycles
10-bit resolution : 59 ØAD cycles
• With the sample and hold function
8-bit resolution : 28 ØAD cycles
10-bit resolution : 33 ØAD cycles
NOTES:
1. Analog input voltage is not affected by the sample and hold function status.
2. ØAD frequency must be 16 MHz or below when VCC=5V.
Without the sample and hold function, the ØAD frequency is 250 kHz or above.
With the sample and hold function, the ØAD frequency is 1 MHz or above.
3. AVCC = VREF = VCC, A/D input voltage (for AN0 to AN7, AN00 to AN07 and AN20 to AN27, AN150 to AN157,
ANEX0 and ANEX1) ≤ VCC.
Rev. 1.10 Oct. 18, 2005 Page 219 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
000
AN20
001
AN21
010
AN22
011
AN23
100
AN24
101
AN25
110
AN26
111
AN27
0
ADTRG
1
Timer B2 interrupt request
of the three-phase motor
control timer functions
1
EX TRG0
TRG bit in the
AD0CON0 register
TRG0 bit in the
AD0CON2 register
000
001
010
OPA1 and OPA0 bits in
the AD0CON1 register
011
100
P96 ANEX1
P95 ANEX0
1X
101
110
X1
01
111
11
AN0
AN1
AN2
P10
AN3
AN4
AN5
AN6
AN7
000
000
001
001
010
010
00
011
011
10 01
00 11
100
100
APS1 and APS0 bits in
the AD0CON2 register
101
101
110
110
CH2 to CH0 bits in
the AD0CON0 register
111
111
CH2 to CH0 bits in
the AD0CON0 register
AD00 register
Comparator 0
AD01 register
AD02 register
Decoder
AD03 register
AD04 register
AD05 register
AD06 register
AD07 register
AD0CON0 register
Successive
conversion register
Resistor ladder
AD0CON1 register
AD0CON2 register
1
1/3
AD0CON3 register
1/2
1
0
1
1
1/2
AD0CON4 register
fAD
0
1/2
0
0
CSK2 bit in the AD0CON3 register
CSK0 bit in the AD0CON0 register
CSK1 bit in the AD0CON1 register
NOTE:
1. These pins are provided in the 144-pin package.
Figure 17.1 A/D Converter Block Diagram
Rev. 1.10 Oct. 18, 2005 Page 220 of 435
REJ09B0162-0110
ØAD
P2
AN00
AN01
AN02
AN03
AN04
P0
AN05
AN06
AN07
AN150
AN151
AN152
AN153
AN154
AN155
AN156
AN157
P15(1)
17. A/D Converter
M32C/88 Group (M32C/88T)
A/D0 Control Register 0(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
AD0CON0
Bit
Symbol
Address
039616
After Reset
0016
Bit Name
Function
RW
b2 b1b0
CH0
CH1
Analog Input Pin
Select Bit(2, 3, 8, 9)
CH2
0 0 0: ANi0
0 0 1: ANi1
0 1 0: ANi2
0 1 1: ANi3
1 0 0: ANi4
1 0 1: ANi5
1 1 0: ANi6
1 1 1: ANi7
RW
RW
(i=none, 0, 2, 15)
RW
b4 b3
MD0
MD1
0 0: One-shot mode
A/D Operating Mode 0 1: Repeat mode
Select Bit 0(2, 6, 7)
1 0: Single sweep mode
1 1: Repeat sweep mode 0 or 1
RW
RW
TRG
Trigger Select Bit
0: Software trigger
1: External trigger, hardware trigger(4)
RW
ADST
A/D Conversion
Start Flag
0: A/D conversion stops
1: A/D conversion starts(4)
RW
CKS0
Frequency Select
Bit
(Note 5)
RW
NOTES:
1. When the AD0CON0 register is rewritten during the A/D conversion, the conversion result is
indeterminate.
2. Analog input pins must be set again after changing an A/D operating mode.
3. The CH2 to CH0 bit settings are enabled in one-shot mode and repeat mode.
4. To set the TRG bit to "1", select the cause of trigger by setting the TRG0 bit in the AD0CON2 register.
Then set the ADST bit to "1" after the TRG bit is set to "1".
5. AD frequency must be under 16 MHz when VCC=5V.
Combination of the CKS0, CKS1, and CKS2 bits selects AD.
The CKS2 Bit in the
AD0CON3 Register
The CKS0 Bit in the
AD0CON0 Register
0
0
1
1
0
The CKS1 Bit in the
AD0CON1 Register
0
1
0
1
0
1
AD
fAD divided by 4
fAD divided by 3
fAD divided by 2
fAD
fAD divided by 8
fAD divided by 6
6. When the MSS bit in the AD0CON3 register is set to "1" (multi-port sweep mode enabled), set the
MD1 and MD0 bits to "102" to enter multi-port single sweep mode and to "112" to enter multi-port
repeat sweep mode 0.
7. When the MSS bit is set to "1", the MD1 and MD0 bits cannot be set to "002" or "012".
8. AVCC=VREF=VCC, AD input voltage (for AN0 to AN7, AN00 to AN07, AN20 to AM27, AN150 to AN157,
ANEX0, ANEX1) ≤ VCC.
9. Set the PSC_7 bit in the PSC register to "1" to use the P10 pin as an analog input pin.
Figure 17.2 AD0CON0 Register
Rev. 1.10 Oct. 18, 2005 Page 221 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
A/D0 Control Register 1(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
AD0CON1
039716
Bit
Symbol
After Reset
0016
Bit Name
Function
RW
Single sweep mode and repeat sweep mode 0
b1 b0
0 0: ANi0, ANi1
0 1: ANi0 to ANi3
1 0: ANi0 to ANi5
1 1: ANi0 to ANi7
Repeat sweep mode 1(3)
SCAN0
A/D Sweep Pin
Select Bit(2, 10)
SCAN1
RW
b1 b0
0 0: ANi0
0 1: ANi0, ANi1
1 0: ANi0 to ANi2
1 1: ANi0 to ANi3
(i=none, 0, 2, 15)
RW
Multi-port single sweep mode and
multi-port repeat sweep mode 0(4)
b1 b0
1 1: ANi0 to ANi7
MD2
A/D Operating
Mode Select Bit 1
0: Any mode other than repeat sweep mode 1
RW
1: Repeat sweep mode 1(5)
BITS
8/10-Bit Mode
Select Bit
0: 8-bit mode
1: 10-bit mode
RW
CKS1
Frequency Select
Bit
(Note 6)
RW
VCUT
VREF Connection
Bit
0: No VREF connection(11)
1: VREF connection
RW
b7 b6
OPA0
OPA1
External Op-Amp
Connection Mode
Bit(7, 9)
0 0: ANEX0 and ANEX1 are not used(8)
0 1: Signal into ANEX0 is A/D converted
1 0: Signal into ANEX1 is A/D converted
1 1: External op-amp connection mode
RW
RW
NOTES:
1. When the AD0CON1 register is rewritten during the A/D conversion, the conversion result is
indeterminate.
2. The SCAN1 and SCAN0 bit settings are disabled in single sweep mode, repeat sweep mode 0, repeat
sweep mode 1, mutli-port single sweep mode and multi-port repeat sweep mode 0.
3. This pin is commonly used in the A/D conversion when the MD2 bit is set to "1".
4. In multi-port single sweep mode or multi-port repeat sweep mode 0, do not set the SCAN1 and
SCAN0 bits to any setting other than "112".
5. When the MSS bit in the AD0CON3 register is set to "1" (multi-port sweep mode enabled), set the
MD2 bit to "0".
6. Refer to the note for the CKS0 bit in the AD0CON0 register.
7. In one-shot mode and repeat mode, the OPA1 and OPA0 bits can be set to "012" or "102" only. Do not
set the OPA0 and OPA1 bits to "012" or "102" in other modes.
8. To set the OPA1 and OPA0 bits to "002", set the PSL3_5 bit in PSL3 register to "0" (other than
ANEX0) and the PSL3_6 bit to "0" (other than ANEX1).
9. When the MSS bit is set to "1", set the OPA1 and OPA0 bits to "002".
10. AVCC=VREF=VCC, AD input voltage (for AN0 to AN7, AN00 to AN07, AN20 to AM27, AN150 to AN157,
ANEX0, ANEX1) ≤ VCC.
11. Do not set the VCUT bit to "0" during the A/D conversion.
VREF is a reference voltage for AD0 only. The VCUT bit setting does not affect the VREF performance
of the D/A converter.
Figure 17.3 AD0CON1 Register
Rev. 1.10 Oct. 18, 2005 Page 222 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
A/D0 Control Register 2(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
AD0CON2
0 0
Bit
Symbol
SMP
Address
039416
Bit Name
A/D Conversion
Method Select Bit
After Reset
XX0X X0002
Function
RW
0: Without the sample and hold funtion
RW
1: With the sample and hold function
b2b1
APS0
Analog Input Port
Select Bit(2, 3)
APS1
(b4 - b3)
TRG0
(b7 - b6)
0 0: AN0 to AN7, ANEX0, ANEX1
0 1: AN150 to AN157
1 0: AN00 to AN07
1 1: AN20 to AN27
Rev. 1.10 Oct. 18, 2005 Page 223 of 435
REJ09B0162-0110
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
External Trigger
Request Cause
Select Bit
0: Selects ADTRG
1: Selects a timer B2 interrupt request
RW
of the three-phase motor control
timer functions (after the ICTB2
counter completes counting)
Reserved Bit
Set to "0".
RW
When read, its content is indeterminate.
NOTES:
1. When the AD0CON2 register is rewritten during the A/D conversion, the conversion result is
indeterminate.
2. When the MSS bit in the AD0CON3 register is set to "1" (multi-port sweep mode enabled), set the
APS1 and APS0 bits to "012".
3. The APS1 and APS0 bits can be set to "012" in the 100-pin package only when the MSS bit in the
AD0CON3 register is set to "1" (multi-port sweep mode enabled).
Figure 17.4 AD0CON2 Register
RW
17. A/D Converter
M32C/88 Group (M32C/88T)
A/D0 Control Register 3(1, 2)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
AD0CON3
0 0 0
Bit
Symbol
Address
039516
After Reset
XXXX X0002
Bit Name
Function
RW
DUS
DMAC Operation
Select Bit(3)
0: Disables DMAC operating mode
1: Enables DMAC operating mode(4, 5)
RW
MSS
Multi-Port Sweep
Mode Select Bit
0: Disables multi-port sweep mode
1: Enables multi-port sweep mode(3, 6)
RW
CKS2
Frequency Select Bit (Note 7)
b4 b3
MSF0
Multi-Port Sweep
Status Flag(8)
MSF1
(b7 - b5)
Reserved Bit
0 0: AN0 to AN7
0 1: AN150 to AN157
1 0: AN00 to AN07
1 1: AN20 to AN27
Set to "0".
When read, its content is indeterminate.
RW
RO
RO
RW
NOTES:
1. When the AD0CON3 register is rewritten during the A/D conversion, the conversion result is
indeterminate.
2. The AD0CON3 may be read uncorrectly during the A/D conversion. It must be read or written after the
A/D converter stops operating.
3. When the MSS bit is set to "1", set the DUS bit to "1".
4. When the DUS bit is set to "1", the AD00 register stores all A/D conversion results.
5. When the DUS bit is set to "1", set the DMAC.
6. When the MSS bit is set to "1", set the MD2 bit in the AD0CON1 register to "0" (other than repeat
sweep mode 1), the APS1 and APS0 bits in the AD0CON2 register to "012" (AN150 to AN157) and the
OPA1 and OPA0 bits in the AD0CON1 register to "002" (ANEX0 and ANEX1 not used).
7. Refer to the note for the CKS0 bit in the AD0CON0 register.
8. The MSF1 and MSF0 bit settings are enabled when the MSS bit is set to "1". Value in the bit is
indeterminate when the MSS bit is set to "0".
Figure 17.5 AD0CON3 Register
Rev. 1.10 Oct. 18, 2005 Page 224 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
A/D0 Control Register 4(1)
b7
b6
b5
b4
0 0 0 0
b3
b2
b1
b0
0 0
Symbol
AD0CON4
Bit
Symbol
Address
After Reset
039216
XXXX 00XX2
Bit Name
Reserved Bit
(b1 - b0)
Function
RW
Set to "0".
When read, its content is indeterminate
RW
b3 b2
MPS10
Multi-Port Sweep
Port Select Bit(2)
MPS11
Reserved Bit
(b7 - b4)
0 0: (Note 3)
0 1: AN0 to AN7, AN150 to AN157
1 0: AN0 to AN7, AN00 to AN07
1 1: AN0 to AN7, AN20 to AN27
RW
RW
Set to "0".
When read, its content is indeterminate
RW
NOTES:
1. When the AD0CON4 register is rewritten during the A/D conversion, the conversion result is
indeterminate.
2. The MPS11 and MPS10 bits cannot be set to "012" in the 100-pin package.
3. When the MSS bit in the AD0CON3 regsiter is set to "0" (multi-port sweep mode disabled), set the
MPS11 and MPS10 bits to "002".
When the MSS bit is set to "1" (multi-port sweep mode enabled), set the MPS11 and MPS10 bits to
"012", "102" or "112".
A/D0 Register i (i =0 to 7)(1, 2, 3, 4, 5)
b15
b8 b7
b0
Symbol
AD00
AD01 to AD03
AD04 to AD06
AD07
Address
038116 - 038016
038316 - 038216, 038516 - 038416, 038716 - 038616
038916 - 038816, 038B16 - 038A16, 038D16 - 038C16
038F16 - 038E16
After Reset
00000000 XXXXXXXX2
Indeterminate
Indeterminate
Indeterminate
Function
RW
8 low-order bits in an A/D conversion result
RO
In 10-bit mode: 2 high-order bits in an A/D conversion result
In 8-bit mode: When read, its content is indeterminate
RO
When read, its content is indeterminate.
RO
NOTES:
1. In DMAC operating mode, register value read by program is indeterminate.
2. Register value is indeterminate when written while the A/D conversion is stopped.
3. Register value is indeterminate if the next A/D conversion result is stored before reading the register.
4. The AD00 register is available in DMAC operating mode. Other registers are indeterminate.
5. In DMAC operating mode and 10-bit mode, set DMAC for a 16-bit transfer.
Figure 17.6 AD0CON4 Register and AD00 to AD07 Registers
Rev. 1.10 Oct. 18, 2005 Page 225 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
17.1 Mode Description
17.1.1 One-shot Mode
In one-shot mode, analog voltage applied to a selected pin is converted to a digital code once. Table 17.2
lists specifications of one-shot mode.
Table 17.2 One-shot Mode Specifications
Item
Function
Specification
The CH2 to CH0 bits in the AD0CON0 register, the OPA1 and OPA0 bits in the
AD0CON1 register and the APS1 and APS0 bits in the AD0CON2 register select a
pin. Analog voltage applied to the pin is converted to a digital code once
Start Condition
• When the TRG bit in the AD0CON0 register is set to "0" (software trigger),
the ADST bit in the AD0CON0 register is set to "1" (A/D conversion starts) by
program
• When the TRG bit is set to "1" (external trigger, hardware trigger):
__________
- a falling edge is applied to the AD TRG pin after the ADST bit is set to "1" by
program
- The timer B2 interrupt request of three-phase motor control timer functions
(after the ICTB2 register counter completes counting) is generated after the
ADST bit is set to "1" by program
Stop Condition
• A/D conversion is completed (the ADST bit is set to "0" when the software trigger is
selected)
• The ADST bit is set to "0" (A/D conversion stopped) by program
Interrupt Request Generation Timing A/D conversion is completed
Analog Voltage Input Pins
Select one pin from ANi0 to ANi7 (i=none, 0, 2, 15), ANEX0 or ANEX1
Reading of A/D Conversion Result • When the DUS bit in the AD0CON3 register is set to "0" (DMAC operating
mode disabled), the microcomputer reads the AD0j register (j=0 to 7) corresponding to selected pin
• When the DUS bit is set to "1" (DMAC operating mode enabled), do not read the
AD00 register. A/D conversion result is stored in the AD00 register after the A/D
conversion is completed. DMAC transfers the conversion result to any memory
space. Refer to 12. DMAC for DMAC settings
Rev. 1.10 Oct. 18, 2005 Page 226 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
17.1.2 Repeat Mode
In repeat mode, analog voltage applied to a selected pin is repeatedly converted to a digital code. Table
17.3 lists specifications of repeat mode.
Table 17.3 Repeat Mode Specifications
Item
Function
Specification
The CH2 to CH0 bits in the AD0CON0 register, the OPA1 and OPA0 bits in the
AD0CON1 register and the APS1 and APS0 bits in the AD0CON2 register select a
pin. Analog voltage applied to the pin is repeatedly converted to a digital code
Start Condition
Same as one-shot mode
Stop Condition
The ADST bit in the AD0CON0 register is set to "0" (A/D conversion stopped) by
program
Interrupt Request Generation Timing • When the DUS bit in the AD0CON3 register is set to "0" (DMAC operating
mode disabled), no interrupt request is generated.
• When DUS bit is set to "1" (DMAC operating mode enabled), an interrupt request
is generated every time an A/D conversion is completed.
Analog Voltage Input Pins
Select one pin from ANi0 to ANi7 (i=none, 0, 2, 15), ANEX0 or ANEX1
Reading of A/D Conversion Result • When the DUS bit is set to "0", the microcomputer reads the AD0j register (j=0 to
7) corresponding to the selected pin.
• When DUS bit is set to "1", do not read the AD00 register. A/D conversion result
is stored in the AD00 register after the A/D conversion is completed. DMAC
transfers the conversion result to any memory space.
Refer to 12. DMAC for DMAC settings
Rev. 1.10 Oct. 18, 2005 Page 227 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
17.1.3 Single Sweep Mode
In single sweep mode, analog voltage that is applied to selected pins is converted one-by-one to a digital
code. Table 17.4 lists specifications of single sweep mode.
Table 17.4 Single Sweep Mode Specifications
Item
Function
Specification
The SCAN1 and SCAN0 bits in the AD0CON1 register and the APS1 and APS0
bits in the AD0CON2 register select pins. Analog voltage applied to the pin is
converted one-by-one to a digital code
Start Condition
Same as one-shot mode
Stop Condition
Same as one-shot mode
Interrupt Request Generation Timing • When the DUS bit in the AD0CON3 register is set to "0" (DMAC operating
mode disabled), an interrupt request is generated after a sweep is completed.
• When DUS bit is set to "1" (DMAC operating mode enabled), an interrupt
request is generated every time an A/D conversion is completed
Analog Voltage Input Pins
Select from ANi0 and ANi1 (2 pins) (i=none, 0, 2, 15), ANi0 to ANi3 (4 pins), ANi0 to
ANi5 (6 pins) or ANi0 to ANi7 (8 pins)
Reading of A/D Conversion Result • When the DUS bit is set to "0", the microcomputer reads the AD0j register corresponding to selected pins
• When DUS bit is set to "1", do not read the AD00 register. A/D conversion result
is stored in the AD00 register after the A/D conversion is completed. DMAC
transfers the conversion result to any memory space. Refer to 12. DMAC for
DMAC settings
Rev. 1.10 Oct. 18, 2005 Page 228 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
17.1.4 Repeat Sweep Mode 0
In repeat sweep mode 0, analog voltage applied to selected pins is repeatedly converted to a digital code.
Table 17.5 lists specifications of repeat sweep mode 0.
Table 17.5 Repeat Sweep Mode 0 Specifications
Item
Function
Specification
The SCAN1 and SCAN0 bits in the AD0CON1 register and the APS1 and APS0
bits in the AD0CON2 register select pins. Analog voltage applied to the pins is
repeatedly converted to a digital code
Start Condition
Same as one-shot mode
Stop Condition
The ADST bit in the AD0CON0 register is set to "0" (A/D conversion stopped) by
program
Interrupt Request Generation Timing • When the DUS bit in the AD0CON3 register is set to "0" (DMAC operating mode
disabled), no interrupt request is generated
• When DUS bit is set to "1" (DMAC operating mode enabled), an interrupt request
is generated every time an A/D conversion is completed
Analog Voltage Input Pins
Select from ANi0 and ANi1 (2 pins) (i=none, 0, 2, 15), ANi0 to ANi3 (4 pins), ANi0 to
ANi5 (6 pins) or ANi0 to ANi7 (8 pins)
Reading of A/D Conversion Result • When the DUS bit is set to "0", the microcomputer reads the AD0j register (j=0 to
7) corresponding to selected pins
• When the DUS bit is set to "1", do not read the AD00 register. A/D conversion
result is stored in the AD00 register after the A/D conversion is completed.
DMAC transfers the conversion result to any memory space. Refer to 12. DMAC
for DMAC settings
Rev. 1.10 Oct. 18, 2005 Page 229 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
17.1.5 Repeat Sweep Mode 1
In repeat sweep mode 1, analog voltage selectively applied to eight pins is repeatedly converted to a
digital code. Table 17.6 lists specifications of repeat sweep mode 1.
Table 17.6 Repeat Sweep Mode 1 Specifications
Item
Function
Specification
The SCAN1 and SCAN0 bits in the AD0CON1 register and the APS1 and APS0
bits in the AD0CON2 register select 8 pins. Analog voltage selectively applied to
8 pins is repeatedly converted to a digital code
e.g., When ANi0 is selected (i =none, 0, 2, 15), analog voltage is converted to a
digital code in the following order:
ANi0
ANi1
ANi0
ANi2
ANi0
ANi3 ....... etc.
Start Condition
Same as one-shot mode (Any trigger generated during an A/D conversion is invalid)
Stop Condition
The ADST bit is set to "0" (A/D conversion stopped) by program
Interrupt Request Generation Timing • When the DUS bit in the AD0CON3 register is set to "0" (DMAC operating
mode disabled), no interrupt request is generated
• When DUS bit is set to "1" (DMAC operating mode enabled), an interrupt request
is generated every time an A/D conversion is completed
Analog Voltage Input Pins
ANi0 to ANi7 (8 pins)
Prioritized Pins
ANi0 (1 pin), ANi0 and ANi1 (2 pins), ANi0 to ANi2 (3 pins) or ANi0 to ANi3 (4 pins)
Reading of A/D Conversion Result • When the DUS bit is set to "0", the microcomputer reads the AD0j register (j=0 to
7) corresponding to selected pins
• When the DUS bit is set to "1", do not read the AD00 register. A/D conversion
result is stored in the AD00 register after the A/D conversion is completed.
DMAC transfers the conversion result to any memory space. Refer to 12. DMAC
for DMAC settings
Rev. 1.10 Oct. 18, 2005 Page 230 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
17.1.6 Multi-Port Single Sweep Mode
In multi-port single sweep mode, analog voltage applied to 16 selected pins is converted one-by-one to a
digital code. Set the DUS bit in the AD0CON3 register to "1" (DMAC operating mode enabled). Table
17.7 lists specifications of multi-port single sweep mode.
Table 17.7 Multi-Port Single Sweep Mode Specifications
Item
Function
Specification
The MPS11 and MPS10 bits in the AD0CON4 register select 16 pins. Analog
voltage applied to 16 pins is converted one-by-one to a digital code in the following
order: AN0 to AN7
ANi0 to ANi7 (i=0, 2, 15)
e.g., When the MPS11 and MPS10 bits are set to "102" (AN0 to AN7, AN00 to
AN07), analog voltage is converted to a digital code in the following order:
AN0
AN1
AN2
AN3
AN4
AN00
AN01
.......
AN06
AN07
AN5
AN6
AN7
Start Condition
Same as one-shot mode
Stop Condition
The ADST bit in the AD0CON0 register is set to "0" (A/D conversion stopped) by
program
Interrupt Request Generation Timing An interrupt request is generated every time A/D conversion is completed
(Set the DUS bit to "1")
Analog Voltage Input Pins
Select from AN0 to AN7
AN7
AN150 to AN157, AN0 to AN7
AN00 to AN07 or AN0 to
AN20 to AN27
Reading of A/D Conversion Result Do not read the AD00 register. A/D conversion result is stored in the AD00 register after the A/D conversion is completed. DMAC transfers the conversion result
to any memory space. Refer to 12. DMAC for DMAC settings
(Set the DUS bit to "1")
Rev. 1.10 Oct. 18, 2005 Page 231 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
17.1.7 Multi-Port Repeat Sweep Mode 0
In multi-port repeat sweep mode 0, analog voltage that is applied to 16 selected pins is repeatedly converted to a digital code. Set the DUS bit in the AD0CON3 register to "1" (DMAC operating mode enabled). Table 17.8 lists specifications of multi-port repeat sweep mode 0.
Table 17.8 Multi-Port Repeat Sweep Mode 0 Specifications
Item
Function
Specification
The MPS11 and MPS10 bits in the AD0CON4 register select 16 pins. Analog
voltage applied to the 16 pins is repeatedly converted to a digital code in the following order: AN0 to AN7
ANi0 to ANi7 (i=0, 2, 15)
e.g., When the MPS11 and MPS10 bits are set to "10 2" (AN0 to AN7, AN00 to AN07),
analog voltage is repeatedly converted to a digital code in the following order:
AN0
AN1
AN00
AN01
AN2
AN3
AN4
.......
AN06
AN07
AN5
AN6
Start Condition
Same as one-shot mode
Stop Condition
The ADST bit is set to "0" (A/D conversion stopped) by program
AN7
Interrupt Request Generation Timing An interrupt request is generated after each A/D conversion is completed
(Set the DUS bit to "1")
Analog Voltage Input Pins
Selectable from AN0 to AN7
AN0 to AN7
AN150 to AN157, AN0 to AN7
AN00 to AN07 or
AN20 to AN27
Reading of A/D Conversion Result Do not read the AD00 register. A/D conversion result is stored in the AD00 register after the A/D conversion is completed. DMAC transfers the conversion result
to any memory space. Refer to 12. DMAC for DMAC settings
(Set the DUS bit to "1")
Rev. 1.10 Oct. 18, 2005 Page 232 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
17.2 Functions
17.2.1 Resolution Select Function
The BITS bit in the AD0CON1 register determines the resolution. When the BITS bit is set to "1" (10-bit
precision), the A/D conversion result is stored into bits 9 to 0 in the AD0j register (j = 0 to 7). When the
BITS bit is set to "0" (8-bit precision), the A/D conversion result is stored into bits 7 to 0 in the AD0j
register.
17.2.2 Sample and Hold Function
When the SMP bit in the AD0CON2 register is set to "1" (with the sample and hold function), A/D conversion rate per pin increases to 28 ØAD cycles for 8-bit resolution and 33 ØAD cycles for 10-bit resolution.
The sample and hold function is available in all operating modes. Start the A/D conversion after selecting
whether the sample and hold function is to be used or not.
17.2.3 Trigger Select Function
The TRG bit in the AD0CON0 register and the TRG0 bit in the AD0CON2 register select the trigger to
start the A/D conversion. Table 17.9 lists settings of the trigger select function.
Table 17.9 Trigger Select Function Settings
Bit and Setting
AD0CON0 Register
TRG = 0
Trigger
AD0CON2 Register
-
Software trigger
The A/D0 starts the A/D conversion when the ADST bit in the
AD0CON0 register is set to "1"
TRG = 1(1)
TRG0 = 0
External trigger(2)
__________
Falling edge of a signal applied to ADTRG
TRG0 = 1
Hardware trigger(2)
The timer B2 interrupt request of three-phase motor control timer
functions (after the ICTB2 counter completes counting)
NOTES:
1. A/D0 starts the A/D conversion when the ADST bit is set to "1" (A/D conversion started) and a trigger is generated.
2. The A/D conversion is restarted if an external trigger or a hardware trigger is inserted during the A/D conversion.
(The A/D conversion in process is aborted.)
17.2.4 DMAC Operating Mode
DMAC operating mode is available with all operating modes. When the A/D converter is in multi-port
single sweep mode or multi-port repeat sweep mode 0, the DMAC operating mode must be used. When
the DUS bit in the AD0CON3 register is set to "1" (DMAC operating mode enabled), all A/D conversion
results are stored into the AD00 register. DMAC transfers data from the AD00 register to any memory
space every time an A/D conversion is completed in each pin. 8-bit DMA transfer must be selected for 8bit resolution and 16-bit DMA transfer for 10-bit resolution. Refer to 12. DMAC for instructions.
Rev. 1.10 Oct. 18, 2005 Page 233 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
17.2.5 Extended Analog Input Pins
In one-shot mode and repeat mode, the ANEX0 and ANEX1 pins can be used as analog input pins. The
OPA1 and OPA0 bits in the AD0CON1 register select which pins to use as analog input pins. An A/D
conversion result for the ANEX0 pin is stored into the AD00 register. The result for the ANEX1 pin is
stored into the AD01 register, but is stored into the AD00 register when the DUS bit in the AD0CON3
register is set to "1" (DMAC operating mode enabled).
Set the APS1 and APS0 bits in the AD0CON2 register to "002" (AN0 to AN7, ANEX0, ANEX1) and the
MSS bit in the AD0CON3 register to "0" (multi-port sweep mode disabled).
17.2.6 External Operating Amplifier (Op-Amp) Connection Mode
In external op-amp connection mode, multiple analog voltage can be amplified by one external op-amp
using extended analog input pins ANEX0 and ANEX1.
When the OPA1 and OPA0 bits in the AD0CON1 register are set to "112" (external op-amp connection),
voltage applied to the AN0 to AN7 pins are output from ANEX0. Amplify this output signal by an external
op-amp and apply it to ANEX1.
Analog voltage applied to ANEX1 is converted to a digital code and the A/D conversion result is stored
into the corresponding AD0j register (j=0 to 7). A/D conversion rate varies depending on the response of
the external op-amp. The ANEX0 pin cannot be connected to the ANEX1 pin directly.
Set the APS1 and APS0 bits in the AD0CON2 register to "002" (AN0 to AN7, ANEX0, ANEX1).
Figure 17.7 shows an example of an external op-amp connection.
Table 17.10 Extended Analog Input Pin Settings
AD0CON1 Register
OPA1 Bit
ANEX0 Function
ANEX1 Function
OPA0 Bit
0
0
Not used
Not used
0
1
P95 as an analog input
Not used
1
0
Not used
P96 as an analog input
1
1
Output to an external op-amp
Input from an external op-amp
Analog
input
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
Resistor ladder
Successive conversion register
ANEX0
002
ANEX1
External op-amp
Figure 17.7 External Op-Amp Connection
Rev. 1.10 Oct. 18, 2005 Page 234 of 435
REJ09B0162-0110
APS1 and APS0 bits
in the AD0CON2
register
Comparator 0
17. A/D Converter
M32C/88 Group (M32C/88T)
17.2.7 Power Consumption Reducing Function
When the A/D converter is not used, the VCUT bit in the AD0CON1 register isolates the resistor ladder of
the A/D converter from the reference voltage input pin (VREF). Power consumption is reduced by shutting
off any current flow into the resistor ladder from the VREF pin.
When using the A/D converter, set the VCUT bit to "1" (VREF connection) before setting the ADST bit in
the AD0CON0 register to "1" (A/D conversion started). Do not set the ADST bit and VCUT bit to "1"
simultaneously, nor set the VCUT bit to "0" (no VREF connection) during the A/D conversion. The VCUT
bit does not affect the VREF performance of the D/A converter.
17.2.8 Output Impedance of Sensor Equivalent Circuit under A/D Conversion
For perfect A/D converter performance, complete internal capacitor (C) charging, shown in Figure 17.8,
for the specified period (T) as sampling time. Output Impedance of the sensor equivalent circuit (R0) is
determined by the following equations:
VC = VIN {1 – e
When t = T, VC = VIN –
e
–
–
1
X
Y
T
C (R0 + R)
=
–
1
C (R0 + R)
t
}
VIN = VIN (1 –
X
)
Y
X
Y
X
1
T= ln
C (R0 +R)
Y
T
R0 = –
X
C • ln
Y
–R
where:
VC = Voltage between pins
R = Internal resistance of the microcomputer
X = Precision (error) of the A/D converter
Y = Resolution of the A/D converter (1024 in 10-bit mode, and 256 in 8-bit mode)
Figure 17.8 shows analog input pin and external sensor equivalent circuit. The impedance (R0) can be
obtained if the voltage between pins (VC) changes from 0 to VIN-(0.1/1024) VIN in the time (T), when the
difference between VIN and VC becomes 0.1LSB.
(0.1/1024) means that A/D precision drop, due to insufficient capacitor charge, is held to 0.1LSB at time of A/
D conversion in the 10-bit mode. Actual error, however, is the value of absolute precision added to 0.1LSB.
When ØAD = 10 MHz, T = 0.3 µs in the A/D conversion mode with the sample and hold function. Output
impedance (R0) for sufficiently charging capacitor (C) in the time (T) is determined by the following equation:
Using T = 0.3 µs, R = 7.8 kΩ, C = 1.5 pF, X = 0.1, Y = 1024,
R0 = –
0.3 X 10-6
1.5 X 10 –12 • ln
0.1
–7.8 X103 = 13.9 X 103
1024
Thus, the allowable output impedance of the sensor equivalent circuit, making the precision (error)
0.1LSB or less, is approximately 13.9 kΩ maximum.
Rev. 1.10 Oct. 18, 2005 Page 235 of 435
REJ09B0162-0110
17. A/D Converter
M32C/88 Group (M32C/88T)
Microcopmuter
Sensor equivalent
circuit
R0
R (7.8Ω)
VIN
Sampling time
C (1.5pF)
VC
3
Sample and hold function is enabled : φAD
2
Sample and hold function is disabled : φAD
Figure 17.8 Analog Input Pin and External Sensor Equivalent Circuit
Rev. 1.10 Oct. 18, 2005 Page 236 of 435
REJ09B0162-0110
18. D/A Converter
M32C/88 Group (M32C/88T)
18. D/A Converter
The D/A converter consists of two separate 8-bit R-2R ladder D/A converters.
Digital code is converted to an analog voltage when a value is written to the corresponding DAi registers
(i=0,1). The DAiE bit in the DACON register determines whether the D/A conversion result output is provided or not. Set the DAiE bit to "1" (output enabled) to disable a pull-up of a corresponding port.
Output analog voltage (V) is calculated from value n (n=decimal) set in the DAi register.
V = VREF x n (n = 0 to 255)
256
VREF : reference voltage (not related to VCUT bit setting in the AD0CON1 register)
Table 18.1 lists specifications of the D/A converter. Table 18.2 lists the DA0 and DA1 pin settings. Figure
18.1 shows a block diagram of the D/A converter. Figure 18.2 shows the D/A control register. Figure 18.3
shows a D/A converter equivalent circuit.
When the D/A converter is not used, set the DAi register to "0016" and the DAiE bit to "0" (output disabled).
Table 18.1 D/A Converter Specifications
Item
D/A Conversion Method
Resolution
Analog Output Pin
Specification
R-2R
8 bits
2 channels
Table 18.2 Pin Settings
Port
Function
Bit and Setting
PD9
Register(1)
PS3 Register(1)
PSL3 Register
P93
DA0 output
PD9_3=0
PS3_3=0
PSL3_3=1
P94
DA1 output
PD9_4=0
PS3_4=0
PSL3_4=1
NOTE:
1. Set the PD9 and PS3 registers immediately after the PRC2 bit in the PRCR register is set to "1" (write
enabled). Do not generate an interrupt or a DMA transfer between the instruction to set the PRC2 bit to "1"
and the instruction to set the PD9 and PS3 registers.
Rev. 1.10 Oct. 18, 2005 Page 237 of 435
REJ09B0162-0110
18. D/A Converter
M32C/88 Group (M32C/88T)
AA
AA
Low-order Bits of Data Bus
DA0 Register
DA0E 0
R-2R Resistor Ladder
A
DA0
1
DA1 Register
DA1E 0
R-2R Resistor Ladder
DA1
1
DA0E, DA1E: Bits in the DACON register
Figure 18.1 D/A Converter
Rev. 1.10 Oct. 18, 2005 Page 238 of 435
REJ09B0162-0110
18. D/A Converter
M32C/88 Group (M32C/88T)
D/A Control Register
b7
b6
b5
b4
b3
b2
b1
Symbol
DACON
b0
Address
039C16
After Reset
XXXX XX002
Bit
Symbol
Bit Name
DA0E
D/A0 Output Enable Bit
0: Disables an output
1: Enables an output
RW
DA1E
D/A1 Output Enable Bit
0: Disables an output
1: Enables an output
RW
(b7 - b2)
Function
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
D/A Register i (i=0, 1)
b7
b0
Symbol
DA0, DA1
Address
039816, 039A16
After Reset
Indeterminate
Function
Output value of D/A conversion
Setting Range
RW
0016 to FF16
RW
Figure 18.2 DACON Register, DA0 and DA1 Registers
r
DA0E
"0"
R
R
R
R
R
R
R
2R
DA0
"1"
2R
2R
2R
2R
2R
2R
2R
LSB
MSB
D/A register 0
2R
0
1
AVSS
VREF(4)
NOTES:
1. The above applies when the DA0 register is set to "2A16".
2. This circuitry is the same for D/A1.
3. To reduce power consumption when the D/A converter is not used, set the DAiE bit (i=0, 1) to "0"
(output disabled) and the DAi register to "0016" to stop current from flowing into the R-2R resistor.
4. VREF is not related to VCUT bit setting in the AD0CON1 register.
Figure 18.3 D/A Converter Equivalent Circuit
Rev. 1.10 Oct. 18, 2005 Page 239 of 435
REJ09B0162-0110
20. CRC Calculation
M32C/88 Group (M32C/88T)
19. CRC Calculation
The CRC (Cyclic Redundancy Check) calculation detects an error in data blocks. A generator polynomial
of CRC_CCITT (X16 + X12 + X5 + 1) generates CRC code.
The CRC code is a 16-bit code generated for a block of data of desired length. This block of data is in 8-bit
units.The CRC code is set in the CRCD register every time one-byte data is transferred to the CRCIN
register after a default value is written to the CRCD register. CRC code generation for one-byte data is
completed in two cycles.
Figure 19.1 shows a block diagram of a CRC circuit. Figure 19.2 shows CRC-associated registers. Figure
19.3 shows an example of the CRC calculation.
High-order bits of data bus
AAA
AAAA AAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAA
AAAAAA
Low-order bits of data bus
8 low-order bits
8 highorder bits
CRCD register
CRC code generation circuit
x16 + x12 + x5 + 1
CRCIN register
Figure 19.1 CRC Calculation Block Diagram
CRC Data Register
b15
b8 b7
b0
Symbol
Address
After Reset
CRCD
037D16- 037C16
Indeterminate
Function
After default value is written to the CRCD
register, the CRC code can be read from the
CRCD register by writing data to the CRCIN
register. Bit position of the default value is
inversed. The inversed value is read as the
CRC code.
Setting Range
RW
000016 to FFFF16
RW
CRC Input Register
b7
b0
Symbol
CRCIN
Address
037E16
Function
Data input.
Inverse bit position of data
Figure 19.2 CRCD Register and CRCIN Register
Rev. 1.10 Oct. 18, 2005 Page 240 of 435
REJ09B0162-0110
After Reset
Indeterminate
Setting Range
RW
0016 to FF16
RW
20. CRC Calculation
M32C/88 Group (M32C/88T)
CRC Calculation and Setup Procedure to Generate CRC Code for "80C416"
CRC Calculation for M32C
value of the CRCIN register with inversed bit position
generator polynomial
CRC Code: a remainder of a division,
16
Generator Polynomial: X
12
+X
5
+ X + 1 (1 0001 0000 0010 00012)
Setting Steps
(1) Inverse a bit position of "80C416" per byte by program
"8016"
"0116", "C416"
"2316"
b15
b0
(2) Set "000016" (default value)
CRCD register
b7
b0
CRCIN register
Bit position of the CRC code for "8016"
(918816) is inversed to "118916", which is
stored into the CRCD register in 3rd cycle.
(3) Set "0116"
b15
b0
CRCD register
118916
b7
b0
CRCIN register
Bit position of the CRC code for "80C416"
(825016) is inversed to "0A4116", which is
stored into the CRCD register in 3rd cycle.
(4) Set "2316"
b15
b0
0A4116
CRCD register
Details of CRC Calculation
As shown in (3) above, bit position of "0116" (000000012) written to the CRCIN register is inversed and becomes
"100000002".
Add "1000 0000 0000 0000 0000 00002", as "100000002" plus 16 digits, to "000016" as the default value of the
CRCD register to perform the modulo-2 division.
1000 1000
Modulo-2 Arithmetic is
data
1 0001 0000 0010 0001 1000 0000 0000 0000 0000 0000
calculated on the law below.
1000 1000 0001 0000 1
0+0=0
1000 0001 0000 1000 0
0+1=1
Generator Polynomial
1000 1000 0001 0000 1
1+0=1
1001 0001 1000 1000
1+1=0
-1=1
CRC Code
"0001 0001 1000 10012 (118916)", the remainder "1001 0001 1000 10002 (918816)" with inversed bit position, can
be read from the CRCD register.
When going on to (4) above, "2316 (001000112)" written in the CRCIN register is inversed and becomes
"110001002".
Add "1100 0100 0000 0000 0000 00002", as "110001002" plus 16 digits, to "1001 0001 1000 10002" as a
remainder of (3) left in the CRCD register to perform the modulo-2 division.
"0000 1010 0100 00012 (0A4116)", the remainder with inversed bit position, can be read from CRCD register.
Figure 19.3 CRC Calculation
Rev. 1.10 Oct. 18, 2005 Page 241 of 435
REJ09B0162-0110
20. X/Y Conversion
M32C/88 Group (M32C/88T)
20. X/Y Conversion
The X/Y conversion rotates a 16 x 16 matrix data by 90 degrees and inverses high-order bits and low-order
bits of a 16-bit data. Figure 20.1 shows the XYC register.
The 16-bit XiR register (i=0 to 15) and 16-bit YjR register (j=0 to 15) are allocated to the same address. The
XiR register is a write-only register, while the YjR register is a read-only register. Access the XiR and YjR
registers from an even address in 16-bit units. Performance cannot be guaranteed if the XiR and YiR
registers are accessed in 8-bit units.
X/Y Control Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
XYC
02E016
Bit
Symbol
Bit Name
Function
RW
XYC0
Read Mode Set Bit
0: Data is converted
1: Data is not convered
RW
XYC1
Write Mode Set Bit
0: Bit alignment is not converted
1: Bit alignment is converted
RW
(b7 - b2)
Figure 20.1 XYC Register
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
After Reset
XXXX XX002
Page 242 of 435
Noting is assigned. When write, set to "0".
When read, its content is indeterminate.
20. X/Y Conversion
M32C/88 Group (M32C/88T)
The XYC0 bit in the XYC register determines how to read the YjR register.
By reading the YjR register when the XYC0 bit is set to "0" (data conversion), bit j in the X0R to X15R
registers can be read simultaneously.
For example, bit 0 in the X0R register can be read if reading bit 0 in the Y0R register, bit 0 in the X1R
register if reading bit 1 in the Y0R register..., bit 0 in the X14R register if reading bit 14 in the Y0R register
and bit 0 in the X15R register if reading bit 15 in the Y0R register.
Figure 20.2 shows the conversion table when the XYC0 bit is set to "0". Figure 20.3 shows an example of
the X/Y conversion.
Y15R register
Y14R register
Y13R register
Y12R register
Y11R register
Y10R register
Y9R register
Y8R register
Y7R register
Y6R register
Y5R register
Y4R register
Y3R register
Y2R register
Y1R register
Y0R register
Address to be read
b15
b0
Bits in the YjR register
b0
AA
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
b15
Address to
be written
X0R register
X1R register
X2R register
X3R register
X4R register
X5R register
X6R register
X7R register
X8R register
X9R register
X10R register
X11R register
X12R register
X13R register
X14R register
X15R register
Bits in the XiR register
b15
b14
b13
b12
b11
b10
b9
b8
b7
b6
b5
b4
b3
b2
b1
b0
b15
b14
b13
b12
b11
b10
b9
b8
b7
b6
b5
b4
b3
b2
b1
b0
Figure 20.2 Conversion Table when Setting the XYC0 Bit to "0"
X0R register
X1R register
X2R register
Y0R register
Y1R register
Y2R register
X3R register
X4R register
X5R register
X6R register
X7R register
X8R register
Y3R register
Y4R register
Y5R register
Y6R register
Y7R register
Y8R register
X9R register
X10R register
X11R register
X12R register
X13R register
X14R register
X15R register
Y9R register
Y10R register
Y11R register
Y12R register
Y13R register
Y14R register
Y15R register
Figure 20.3 X/Y Conversion
Rev. 1.10 Oct. 18, 2005 Page 243 of 435
REJ09B0162-0110
AAAAAAAA
AAAAAA
AA
AA
AA
AAAAAAA
AA
AA
AA AAAA
AA
AA
AA
AA
AA
AAA
AA
A
20. X/Y Conversion
M32C/88 Group (M32C/88T)
By reading the YjR register when the XYC0 bit in the XYC register is set to "1" (no data conversion), the
value written to the XiR register can be read directly. Figure 20.4 shows the conversion table when the
XYC0 bit is set to "1."
Address to be written
Address to be read
AA
AA
AA
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
AA
A
X0R register, Y0R register
X1R register, Y1R register
X2R register, Y2R register
X3R register, Y3R register
X4R register, Y4R register
X5R register, Y5R register
X6R register, Y6R register
X7R register, Y7R register
X8R register, Y8R register
X9R register, Y9R register
X10R register, Y10R register
X11R register, Y11R register
X12R register, Y12R register
X13R register, Y13R register
X14R register, Y14R register
X15R register, Y15R register
b15
b0
Bits in the XiR register
Bits in the YjR register
i=0 to 15
j=0 to 15
Figure 20.4 Conversion Table when Setting the XYC0 Bit to "1"
The XYC1 bit in the XYC register selects bit alignment of the value in the XiR register.
By writing to the XiR register while the XYC1 bit is set to "0" (no bit alignment conversion), bit alignment is
written as is. By writing to the XiR register while the XYC1 bit is set to "1" (bit sequence replaced), bit
alignment is written inversed.
Figure 20.5 shows the conversion table when the XYC1 bit is set to "1".
b15
b0
b15
b0
Data to be written
Bits in XiR register
(i=0 to 15)
Figure 20.5 Conversion Table when Setting the XYC1 Bit to "1"
Rev. 1.10 Oct. 18, 2005
REJ09B0162-0110
Page 244 of 435
21. Intelligent I/O
M32C/88 Group (M32C/88T)
21. Intelligent I/O
The intelligent I/O is a multifunctional I/O port for time measurement, waveform generating, clock synchronous serial I/O, clock asynchronous serial I/O (UART), HDLC data processing and more.
The intelligent I/O has one 16-bit base timer for free-running operation, eight 16-bit registers for time measurement and waveform generating and two sets of two 8-bit shift registers for communications.
Table 21.1 lists functions and channels of the intelligent I/O.
Table 21.1 Intelligent I/O Functions and Channels
Function
Time
Measurement(1)
Description
8 channels
Digital Filter
8 channels
Trigger Input Prescaler
2 channels (channel 6 and channel 7)
Trigger Input Gate
2 channels (channel 6 and channel 7)
Waveform
Generating(1)
Single-Phase Waveform Output Mode
8 channels
8 channels
Phase-Delayed Waveform Output Mode 8 channels
SR Waveform Output Mode
Communication
8 channels
Communication unit 0
Clock Synchronous Serial I/O Mode
Available
UART Mode
Not Available
HDLC Data Processing Mode
Available
Communication unit 1
Available
NOTE:
1. The time measurement function and the waveform generating function share a pin.
The time measurement function and waveform generating function can be selected for each channel.
The communication function is available by a combining multiple channels.
Rev. 1.10 Oct. 18, 2005 Page 245 of 435
REJ09B0162-0110
21. Intelligent I/O
M32C/88 Group (M32C/88T)
Figures 21.1 shows a block diagram of the intelligent I/O. Figure 21.2 shows a block diagram of the
intelligent I/O communication.
0
1
Overflow of bit 15 in the base timer
Overflow of bit 9 in the base timer
BTRE
Request by matching the base timer with the G1PO0 register
Base timer reset
in the communication unit 1
Request from the INT pin
BTS
f1
11
Two-phase
pulse signal
is applied
10
BCK1 and BCK0
INPC10
INPC11
/ ISCLK1
INPC12
/ ISRxD1
INPC13
INPC14
INPC15
INPC16
INPC17
00
10 : fBT1
Digital 11 : f1
Filter
DF1 and DF0
10 : fBT1 00
Digital 11 : f1
Filter
DF1 and DF0
00
10 : fBT1
Digital 11 : f1
Filter
DF1 and DF0
00
10 : fBT1
Digital 11 : f1
Filter
DF1 and DF0
00
10 : fBT1
Digital 11 : f1
Filter
DF1 and DF0
00
10 : fBT1
Digital 11 : f1
Filter
DF1 and DF0
fBT1
Divider
2(n+1)
DIV4 to DIV0
Base Timer
Edge
Select
CTS1 and CTS0
G1TM0, G1PO0
Register(1)
Edge
Select
CTS1 and CTS0
G1TM1, G1PO1
Register(1)
Edge
Select
CTS1 and CTS0
G1TM2, G1PO2
Register(1)
000 to 010
PWM
Output
MOD2 to MOD0
OUTC10/ISTxD1
/BE1OUT
111
000 to 010
111
MOD2 to MOD0
OUTC11/ISCLK1
OUTC12
PWM
Output
G1TM3, G1PO3
Register(1)
Edge
Select
OUTC13
CTS1 and CTS0
G1TM4, G1PO4
Register(1)
Edge
Select
OUTC14
PWM
Output
CTS1 and CTS0
G1TM5, G1PO5
Register(1)
Edge
Select
CTS1 and CTS0
00
0
10 : fBT1
Edge
Gate
Digital 11 : f1
Select
Function 1
Filter
DF1 and DF0
GT
CTS1 and CTS0
00
0
10 : fBT1
Gate
Digital 11 : f1
Edge
Function 1
Filter
Select
DF1 and DF0
GT
CTS1 and CTS0
OUTC15
0
Prescaler
Function 1
PR
G1TM6, G1PO6
Register(1)
0
Prescaler
Function 1
PR
OUTC16
PWM
Output
G1TM7, G1PO7
Register(1)
OUTC17
Ch0 to Ch7
interrupt request signal
ISCLK0
ISRxD0
Communication
Unit 0
ISTxD0
Communication
Unit 1
f1
f8
f2n
NOTE:
1. Each register is placed in a reset state after the G1BCR0 register
supplies the clock.
Figure 21.1 Intelligent I/O Block Diagram
Rev. 1.10 Oct. 18, 2005 Page 246 of 435
REJ09B0162-0110
DIV4 to DIV0, BCK1 and BCK0: Bits in the G1BCR0 Register
BTS: Bit in the G1BCR1 Register
CTS1 and CTS0, DF1 and DF0, GT, PR: Bits in the G1TMCRj Register (j=0 to 7)
MOD2 to MOD0: Bits in the G1POCRj Register
BTRE: Bit in the G1POCR0 Register
21. Intelligent I/O
M32C/88 Group (M32C/88T)
Communication Unit 0
ISRxD0 ISCLK0
Transmit Interrupt Request
SIO0TR(1)
CCS1 and CCS0
01
f1
f2n
f8
10
11
G0TB Register
(Transmit Buffer Register)
SOF
Generation Circuit
Transmit
Buffer
Bit Insert Circuit
Transmit
Register
Transmit Latch
Transmission
Transmit Data
Generation Circuit
TXSL
G0TCRC
Register
0
ISTxD0
1
Data
Selector
G0TO Register
Clock Wait
Control Circuit
HDLC Data Transmit
Interrupt Request
G0TOR(1)
Transmit
Register
Transmit
CKDIR Operation
0
Clock
Transmit
Buffer
1
Receive Operation Clock
Reception
Arbitration
Receive Data
Generation Circuit
G0RCRC
Register
G0RI Register
Receive
Buffer
Receive
Register
Data
Selector
Bit Insert Check
0
G0RB Register
Receive Interrupt
Request
SIO0RR(1)
Receive
Buffer
1
RXSL
G0DR Register
(Receive Data Register)
Receive
Register
Shift
Register
Buffer
Register
G0CMP0 register
G0CMP0 register
G0CMP0 register
G0CMP3 Register
Special
Communication
Interrupt Request
SRT0R(1)
Special Interrupt
Check
Comparator
Comparator
Comparator
Comparator
HDLC Data Receive
Interrupt Request
G0RIR(1)
Communication Unit 1
G1TB Register
(Transmit Buffer Register)
Generated Clock in
the Channel i (i=1 to 3)
f1
f2n
f8
SOF
Generation Circuit
Transmit
Buffer
Bit Insert Circuit
Transmit
Register
Transmit Latch
Clock Wait
Control Circuit
01
10
11
TXSL
Start Bit
Generation Circuit
CKDIR
ISRxD1
0
HDLC Data
Transmit
Interrupt Request
G1TOR(1)
Reception
Receive Data
Generation Circuit
Bit Insert Check
Data
Selector
G1RB Register
Receive
Buffer
Polarity
Inverse
RXSL
ISTxD1
Transmit
Buffer
G1RCRC
Register
1
Polarity
Inverse
Transmit
Register
Receive
Operation
Clock
G1RI Register
Receive
Register
SIO1TR(1)
G1TO Register
Arbitration
Receive
Buffer
Transmit Interrupt
Request
1
1
ISCLK1
0
Data
Selector
Stop Bit
Generation Circuit
Transmit
Operation
Clock
0
Transmission
G1TCRC
Register
CCS3 and CCS2
00
Transmit Data
Generation Circuit
G1DR Register
(Receive Data Register)
Shift
Register
Start Bit Check
Receive
Register
Stop Bit Check
Special Interrupt
Check
Buffer
Register
G1CMP0 Register
G1CMP0
(8bit) Register
G1CMP0
(8bit) Register
(8bit) Register
G1CMP3
Receive Interrupt
Request
SIO1RR(1)
Special
Communication
Interrupt Request
SRT1R(1)
Comparator
Comparator
(8bit)
Comparator
(8bit)
(8bit)
Comparator
HDLC Data Receive
Interrupt Request
G1RIR(1)
NOTE:
1. See Figure 10.14.
CKDIR: Bit in the GiMR Register (i=0,1)
TXSL, RXSL: Bits in the GiEMR Register
CCS1 and CCS0: Bits in the CCS Register
Figure 21.2 Intelligent I/O Communication Block Diagram
Rev. 1.10 Oct. 18, 2005 Page 247 of 435
REJ09B0162-0110
21. Intelligent I/O
M32C/88 Group (M32C/88T)
Figures 21.3 to 21.8 show registers associated with the intelligent I/O base timer, the time measurement
function and waveform generating function. (For registers associated with the communication function, see
Figures 21.19 to 21.28.)
Base Timer Register 1(2)
b15
b8 b7
b0
Symbol
G1BT
Address
After Reset
012116 - 012016
Indeterminate
Setting Range
Function
When the base timer is counting:
When read, the value of the base timer can be
read.
When write, the counter starts counting from the
value written. When the base timer is reset, the
G1BT register is set to "000016"(1).
When the base timer is reset:
The G1BT register is set to "000016" but value is
indeterminate. No value is written(1).
000016 to FFFF16
RW
RW
NOTES:
1. The base timer stops only when the BCK1 and BCK0 bits in the G1BCR0 register are set to "002" (clock
stopped). The base timer counts when the BCK1 and BCK0 bits are set to a value other than "002".
When the BTS bit in the G1BCR1 register is set to "0", the base timer is reset continually, remaining set
to "000016". This, in effect, places the base timer in a "no counting" state. When the BTS bit is set to "1",
this state is cleared and counting starts.
2. The G1BT register reflects the base timer value after one half fBT1 cycle.
Base Timer Control Register 10
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
G1BCR0
Bit
Symbol
Address
012216
After Reset
0016
Bit Name
Function
RW
b1b0
BCK0
Count Source
Select Bit
BCK1
RW
0 0 : Clock stops
0 1 : Do not set to this value
1 0 : Two-phase pulse signal is applied(1)
RW
1 1 : f1
If setting value is n (n = 0 to 31),
count source is divided by 2(n + 1).
No division if n=31.
DIV0
DIV1
DIV2
RW
Count Source
Divide Ratio
Select Bit
DIV3
b6 b5 b4 b3 b2
(n=0) 0 0 0 0 0: Divide-by-2
(n=1) 0 0 0 0 1: Divide-by-4
(n=2) 0 0 0 1 0: Divide-by-6
RW
(n=30) 1 1 1 1 0: Divide-by-62
(n=31) 1 1 1 1 1: No division
RW
DIV4
IT
RW
RW
Base Timer
Interrupt Select Bit
0: Bit 15 overflows
1: Bit 14 overflows
RW
NOTE:
1. This setting can be used only when the UD1 and UD0 bits in the G1BCR1 register are set to "102"
(two-phase signal processing mode). Do not set the BCK1 and BCK0 bits to "102" when setting the
UD1 and UD0 bits to "002" (counter increment mode) or "012" (Counter increment/decrement mode).
Figure 21.3 G1BT Register and G1BCR0 Register
Rev. 1.10 Oct. 18, 2005 Page 248 of 435
REJ09B0162-0110
21. Intelligent I/O
M32C/88 Group (M32C/88T)
Base Timer Control Register 11
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
012316
G1BCR1
0
Bit
Symbol
(b0)
Bit Name
After Reset
X000 000X2
Function
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
RST1
Base Timer Reset
Cause Select Bit 1
0: The base timer is not reset by
matching with the G1PO0 register
1: The base timer is reset by matching
with the G1PO0 register(1)
RW
RST2
Base Timer Reset
Cause Select Bit 2
0: The base timer is not reset by
applying "L" to the INT0 or INT1 pin
1: The base timer is reset by applying
"L" to the INT0 or INT1 pin(2)
RW
Reserved Bit
Set to "0"
RW
Base Timer
Start Bit
0: Base timer is reset
1: Base timer starts counting
RW
(b3)
BTS
b6 b5
UD0
UD1
(b7)
RW
0 0: Counter increment mode
0 1: Counter increment/decrement mode
Counter Increment/
pulse signal processing
Decrement Control Bit 1 0: Two-phase
mode(3)
RW
1 1: Do not set to this value
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
NOTES:
1. The base timer is reset after two fBT1 clock cycles when the base timer value matches the G1PO0
register setting. (See Figure 21.7 for details on the G1PO0 register.) When the RST1 bit is set to "1",
the G1POj register (j=1 to 7) for the waveform generating function and communication function must
be set to a value smaller than the G1PO0 register.
2. The IPSA_0 bit in the IPSA register can select the INT0 or INT1 pin.
3. In two-phase pulse signal processing mode, the base timer is not reset, even though the RST1 bit is
set to "1", if the counter is decremented after two clock cycles when the base timer value matches the
G1PO0 register setting.
Figure 21.4 G1BCR1 Register
Rev. 1.10 Oct. 18, 2005 Page 249 of 435
REJ09B0162-0110
21. Intelligent I/O
M32C/88 Group (M32C/88T)
Time Measurement Control Register 1j (j=0 to 7)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
G1TMCR0 to G1TMCR3
G1TMCR4 to G1TMCR7
Bit
Symbol
Address
011816, 011916, 011A16, 011B16
011C16, 011D16, 011E16, 011F16
Bit Name
After Reset
0016
0016
Function
RW
b1 b0
CTS0
Time Measurement
Trigger Select Bit
CTS1
0
0
1
1
0: No time measurement
1: Rising edge
0: Falling edge
1: Both edges
RW
RW
b3 b2
DF0
Digital Filter Function
Select Bit
DF1
0
0
1
1
0: No digital filter
1: Do not set to this value
0: fBT1
1: f1
RW
RW
Gate Function
Select Bit(1)
0: Gate function is not used
1: Gate function is used
GOC
Gate Function Clear
Select Bit(1, 2, 3)
0: Not cleared
1: The gate is cleared when the base RW
timer matches the GiPOk register
GSC
Gate Function Clear
Bit(1, 2)
The gate is cleared by setting the
GSC bit to "1"
RW
Prescaler Function
Select Bit(1)
0: Not used
1: Used
RW
GT
PR
RW
NOTES:
1. The GT, GOC, GSC and PR bits in the G1TMCR6 and G1TMCR7 registers can be used to select
these functions.
Set all bits 7 to 4 in the G1TMCR0 to G1TMCR5 registers to "0".
2. The GOC and GSC bits are enabled only when the GT bit is set to "1".
3. The GOC bit is set to "0" after the gate function is cleared. See Figure 21.7 about the G1POk register
(k=4 when j=6 and k=5 when j=7).
Time Measurement Prescaler Register 1j (j=6,7)
b7
b0
Symbol
G1TPR6, G1TPR7
Address
012416, 012516
Function
If the setting value is n, the base timer value is
stored into G1TMj register whenever a trigger input
is counted by n+1(1)
After Reset
0016
Setting Range
RW
0016 to FF16
RW
NOTE:
1. The first prescaler, after the PR bit setting in the G1TMCRj register is changed from "0" (not used) to
"1" (used), may be divided by n rather than n+1. The subsequent prescaler is divided by n+1.
Figure 21.5 G1TMCR0 to G1TMCR7 Registers, G1TPR6 and G1TPR7 Registers
Rev. 1.10 Oct. 18, 2005 Page 250 of 435
REJ09B0162-0110
21. Intelligent I/O
M32C/88 Group (M32C/88T)
Time Measurement Register 1j (j=0 to 7)
b15
b8 b7
b0
Symbol
G1TM0 to G1TM2
G1TM3 to G1TM5
G1TM6, G1TM7
Address
010116 - 010016, 010316 - 010216, 010516 - 010416
010716 - 010616, 010916 - 010816, 010B16 - 010A16
010D16 - 010C16, 010F16 - 010E16
Function
After Reset
Indeterminate
Indeterminate
Indeterminate
Setting Range
The base timer value is stored every
measurement timing
RW
RO
Waveform Generating Control Register 1j (j=0 to 7)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset
G1POCR0
G1POCR1 to G1POCR3
G1POCR4 to G1POCR7
011016
011116, 011216, 011316
011416, 011516, 011616, 011716
0000 X0002
0X00 X0002
0X00 X0002
Bit
Symbol
Bit Name
Function
RW
b2 b1b0
MOD0
MOD1
Operating Mode
Select Bit
MOD2
(b3)
IVL
RLD
BTRE
INV
0 0 0 : Single waveform output mode RW
0 0 1 : SR waveform output mode(1)
0 1 0 : Phase-delayed waveform
output mode
0 1 1 : Do not set to this value
RW
1 0 0 : Do not set to this value
1 0 1 : Do not set to this value
1 1 0 : Do not set to this value(2)
1 1 1 : Use communication function
RW
output(3)
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
Output Initial Value
Select Bit(6)
0: "L" output as default value
1: "H" output as default value
RW
0: Reloads the G1POj register when
G1POj Register Value
value is written
RW
Reload Timing Select Bit 1: Reloads the G1POj register when
the base timer is reset
0: Enables base timer reset when
Base Timer Reset Enable
bit 15 in the base timer overflows
RW
1: Enables base timer reset when
Bit(4)
bit 9 in the base timer overflows(7)
Inverse Output Function
Select Bit(5)
0: Output is not inversed
1: Output is inversed
RW
NOTES:
1. This setting is enabled only for even channels. In SR waveform output mode, values written to the
corresponding odd channel (next channel after an even channel) are ignored. Even channels provides
waveform output. Odd channels provides no waveform output.
2. To receive data in UART mode, set the G1POCR2 register to "0000 01102".
3. This setting is enabled only for channels 0 and 1. To use the ISTxD1 pin, set the MOD2 to MOD0 bits
in the G1POCR0 register to "1112". To use the ISCLK1 pin for an output, set the MOD2 to MOD0 bits
in the G1POCR1 register to"1112". Do not set the MOD2 to MOD0 bits to "1112" except in channels 0
and 1 and for the communication function.
4. The BTRE bit is provided in the G1POCR0 register only. Set each bit 6 in the G1POCR1 to
G1POCR7 registers to "0".
5. The inverse output function is the final step in waveform generating process. When the INV bit is set
to "1", an "H" signal is provided a default output by setting the IVL bit to "0"; and an "L" signal is
provided by setting it to "1".
6. To output either "H" or "L" signal set in the IVL bit, set the FSCj bit in the G1FS register to "0"
(waveform generating function selected) and IFEj bit in the G1FE register to "1" (channel j function
enabled). Then set the IVL bit to "0" or "1".
7. When the BTRE bit is set to "1", set the BCK1 and BCK0 bits in the G1BCR0 register to "112" (f1) and
the UD1 and UD0 bits in the G1BCR1 register to "002" (counter increment mode).
Figure 21.6 G1TM0 to G1TM7 Registers and G1POCR0 to G1POCR7 Registers
Rev. 1.10 Oct. 18, 2005 Page 251 of 435
REJ09B0162-0110
21. Intelligent I/O
M32C/88 Group (M32C/88T)
Waveform Generating Register 1j (j=0 to 7)
b15
b8 b7
b0
Symbol
G1PO0 to G1PO2
G1PO3 to G1PO5
G1PO6 to G1PO7
Address
After Reset
010116-010016, 010316-010216, 010516-010416 Indeterminate
010716-010616, 010916-010816, 010B16-010A16 Indeterminate
010D16-010C16, 010F16-010E16
Indeterminate
Function
Setting Range
RW
• When the RLD bit in the G1POCRj register is set
to "0", value is reloaded into the G1POj register
for output as soon as written, for example, a
waveform output, reflecting the value.
• When the RLD bit is set to "1", the value is
reloaded when the base timer is reset. The value
written can be read until reloading.
000016 to FFFF16
RW
Function Select Register 1
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset
G1FS
012716
0016
Bit
Symbol
FSC0
FSC1
Bit Name
Function
RW
Channel 0 Time Measure- 0: Selects the waveform generating
ment/Waveform Generating
RW
function
Function Select Bit
1: Selects the time measurement
function
Channel 1 Time Measurement/Waveform Generating
RW
Function Select Bit
FSC2
Channel 2 Time Measurement/Waveform Generating
Function Select Bit
RW
FSC3
Channel 3 Time Measurement/Waveform Generating
Function Select Bit
RW
FSC4
FSC5
Channel 4 Time Measurement/Waveform Generating
Function Select Bit
Channel 5 Time Measurement/Waveform Generating
Function Select Bit
RW
RW
FSC6
Channel 6 Time Measurement/Waveform Generating
Function Select Bit
RW
FSC7
Channel 7 Time Measurement/Waveform Generating
Function Select Bit
RW
Figure 21.7 G1PO0 to G1PO7 Registers and G1FS Register
Rev. 1.10 Oct. 18, 2005 Page 252 of 435
REJ09B0162-0110
21. Intelligent I/O
M32C/88 Group (M32C/88T)
Function Enable Register 1
b7
b6
b5
b4
b3
b2
b1
Symbol
b0
G1FE
Bit
Symbol
Address
012616
Bit Name
After Reset
0016
Function
RW
IFE2
Channel 0 Function Enable Bit 0: Disables functions for channel j RW
Channel 1 Function Enable Bit 1: Enables functions for channel j RW
(j=0 to 7)
Channel 2 Function Enable Bit
RW
IFE3
Channel 3 Function Enable Bit
RW
IFE4
Channel 4 Function Enable Bit
RW
IFE5
Channel 5 Function Enable Bit
RW
IFE6
Channel 6 Function Enable Bit
RW
IFE7
Channel 7 Function Enable Bit
RW
IFE0
IFE1
Figure 21.8 G1FE Register
Rev. 1.10 Oct. 18, 2005 Page 253 of 435
REJ09B0162-0110
21. Intelligent I/O (Base Timer)
M32C/88 Group (M32C/88T)
21.1 Base Timer
The base timer is a free-running counter that counts an internally generated count source.
Table 21.2 lists specifications of the base timer. Figures 21.3 and 21.4 show registers associated with the
base timer. Figure 21.9 shows a block diagram of the base timer. Figure 21.10 shows an example of the
base timer in counter increment mode. Figure 21.11 shows an example of the base timer in counter increment/decrement mode. Figure 21.12 shows an example of two-phase pulse signal processing mode.
Table 21.2 Base Timer Specifications
Item
Count Source (fBT1)
Specification
f1 divided by 2(n+1) , two-phase pulse input divided by 2(n+1)
n: determined by the DIV4 to DIV0 bits in the G1BCR0 register
n=0 to 31; however no division when n=31
Counting Operation
The base timer increments the counter value
The base timer increments and decrements the counter value
Two-phase pulse signal processing
Counter Start Condition
The BTS bit in the G1BCR1 register is set to "1" (base timer starts counting)
Counter Stop Condition
The BTS bit in the G1BCR1 register is set to "0" (base timer reset)
Base Timer Reset Condition
• The value of the base timer matches the value of the G1PO0 register
________
_______
• An low-level ("L") signal is applied to the INT0 or INT1 pin
• Bit 15 or bit 9 in the base timer overflows
Value when the Base Timer is Reset
"000016"
Interrupt Request
The BT1R bit in the IIO4IR register is set to "1" (interrupt requested) when bit
9, bit 14 or bit 15 in the base timer overflows (See Figure 10.14.)
Read from Base Timer
• The G1BT register indicates the counter value while the base timer is running
Write to Base Timer
Selectable Function
• The G1BT register is indeterminate when the base timer is reset
When a value is written while the base timer is running, the timer counter
immediately starts counting from this value. No value can be written while
the base timer is reset
• Counter increment/decrement mode
The base timer starts counting when the BTS bit is set to "1". After
reaching to "FFFF16", the timer counter is then decremented back to
"000016". If the RST1 bit in the G1BCR1 register is set to "1" (the base
timer is reset by matching with the G1PO0 register), the timer counter
starts decrementing in two counts after the base timer matches the G1PO0
register. The base timer increments the counter value again when the
timer counter reaches "000016." (See Figure 21.11.)
• Two-phase pulse processing mode
Two-phase pulse signals from P76 and P77 pins or P80 and P81 pins
are counted as well. (See Figure 21.12.)
The IPSA_0 bit in the IPSA register controls input pin selection.
(Refer to 23. Programmable I/O Ports)
P80
(P76)
P81
(P77)
The timer increments
counter on all edge
Rev. 1.10 Oct. 18, 2005 Page 254 of 435
REJ09B0162-0110
The timer decrements
counter on all edges
21. Intelligent I/O (Base Timer)
M32C/88 Group (M32C/88T)
fBT1
BCK1 and BCK0
f1
Apply the Two-Phase
Pulse Signal
Base Timer
2(n+1)
Divider
11
b9
b14 b15
Overflow Signal
1
10
BTRE
0
0
1
BTS Bit
IT
Base Timer
Interrupt Request
(See the BT1R
bit on Figure
10.14)
RST1
Matching with
the G1PO0 Register
Base Timer Reset
RST2
Apply "L" to
the INTi Pin
i=0,1
BCK1 and BCK0, IT: Bits in the G1BCR0 register
RST2 to RST0, BTS: Bits in the G1BCR1 register
BTRE: Bit in the G1POCR0 register
Figure 21.9 Base Timer Block Diagram
Table 21.3 Base Timer Associated Register Settings
(Also applies when using time measurement function, waveform generating function and communication function)
Register
G1BCR0
G1BCR1
G1POCR0
G1BT
Bit
BCK1, BCK0
DIV4 to DIV0
IT
RST2, RST1
BTS
UD1, UD0
BTRE
-
Function
Select count source
Select divide ratio of count source
Select the base timer interrupt
Select source for a base timer reset
Used to start the base timer independently
Select how to count
Select source for a base timer reset
Read or write base timer value
Set the following registers to set the RST1 bit to "1" (base timer reset by matching the base timer with the G1PO0 register).
G1POCR0
MOD2 to MOD0
Set to "0002" (single-phase waveform output mode)
G1PO0
G1FS
G1FE
FSC0
IFE0
Set reset cycle
Set to "0" (waveform generating function)
Set to "1" (channel operation start)
Rev. 1.10 Oct. 18, 2005 Page 255 of 435
REJ09B0162-0110
21. Intelligent I/O (Base Timer)
M32C/88 Group (M32C/88T)
(1) When the IT bit in the G1BCR0 register is set to "0" (bit 15 in the base timer overflows)
FFFF16
Base Timer
800016
000016
"1"
Bit 15 Overflow Signal
"0"
BT1R bit in
the IIO4IR register
"1"
"0"
Write "0" by program
if setting to "0"
The above applies under the following conditions:
• The RST1 in the G1BCR1 register is set to "0" (the base timer is not reset by matching the G1PO0 register)
• The UD1 and UD0 bits in the G1BCR1 register are set to "002" (counter increment mode)
(2) When the IT bit is set to "1" (bit 14 in the base timer overflows)
FFFF16
C00016
Base Timer 800016
400016
000016
Bit 14 Overflow Signal
BT1R bit in
the IIO4IR register
"1"
"0"
"1"
"0"
Write "0" by program
if setting to "0"
The above applies under the following conditions:
• The RST1 in the G1BCR1 register is set to "0" (the base timer is not reset by matching the G1PO0 register)
• The UD1 and UD0 bits in the G1BCR1 register are set to "002" (counter increment mode)
Figure 21.10 Counter Increment Mode
Rev. 1.10 Oct. 18, 2005 Page 256 of 435
REJ09B0162-0110
21. Intelligent I/O (Base Timer)
M32C/88 Group (M32C/88T)
(1) When the IT bit in the G1BCR0 register is set to "0" (bit 15 in the base timer overflows)
FFFF16
Base Timer
800016
Bit 15
Overflow Signal
"1"
"0"
"1"
BT1R bit in the
IIO4IR register
"0"
Write "0" by program
if setting to "0"
The above applies under the following conditions:
• The RST1 in the G1BCR1 register is set to "0" (the base timer is not reset by matching the G1PO0 register)
• The UD1 and UD0 bits in the G1BCR1 register are set to "012" (counter increment/decrement mode)
(2) When the IT bit is set to "1" (bit 14 in the base timer overflows)
FFFF16
C00016
Base Timer
800016
400016
000016
Bit 14 Overflow
Signal
BT1R bit in the
IIO4IR register
"1"
"0"
"1"
"0"
Write "0" by program
if setting to "0"
The above applies under the following conditions:
• The RST1 in the G1BCR1 register is set to "0" (the base timer is not reset by matching the G1PO0 register)
• The UD1 and UD0 bits in the G1BCR1 register are set to "012" (counter increment/decrement mode)
(3) When the RST1 bit in the G1BCR1 register is set to "1" (the base timer is reset by matching with the G1PO0 register)
800216
800016
Base Timer
000016
The above applies under the following conditions:
• Value of G1PO0 register: "800016"
• The UD1 and UD0 bits in the G1BCR1 register are set to "012" (counter increment/decrement mode)
Figure 21.11 Counter Increment/Decrement Mode
Rev. 1.10 Oct. 18, 2005 Page 257 of 435
REJ09B0162-0110
21. Intelligent I/O (Base Timer)
M32C/88 Group (M32C/88T)
(1) When the base timer is reset while the base timer increments the counter value
Input
Waveform
P80 (P76)(2) "H"
(A-phase)
"L"
min 1 µs
P81 (P77)(2) "H"
(B-phase)
"L"
min 1 µs
fBT1 "H"
(
)
When selects no division
"L"
with the divider by 2(n+1)
INT1 "H"
(Z-phase)
"L"
(Note 1)
The base timer starts counting
Base TImer
m
m+1
0
1
2
Set to "1" in this timing
Set to "0" in this timing
(2) When the base timer is reset while the base timer decrements the counter value
P80 (P76)(2)
(A-phase)
"H"
Input
Waveform
"L"
P81 (P77)(2)
(B-phase) "H"
min 1 µs
min 1 µs
"L"
fBT1
(
When selects no division "H"
with the divider by 2(n+1)
) "L"
INT1
(Z-phase) "H"
(Note 1)
"L"
The base timer starts counting
Base TImer
m
m-1
0
FFFF16
FFFE16
Set to "FFFF16" in this timing
Set to "0" in this timing
NOTES:
1. 1.5 fBT1 clock cycles or more are required.
2. Set the IPSA_0 bit in the IPSA register to select either port.
Figure 21.12 Base Timer Operation in Two-phase Pulse Signal Processing Mode
Rev. 1.10 Oct. 18, 2005 Page 258 of 435
REJ09B0162-0110
21. Intelligent I/O (Time Measurement Function)
M32C/88 Group (M32C/88T)
21.2 Time Measurement Function
When external trigger is applied, the base timer value is stored into the G1TMj register (j=0 to 7). Table 21.4
shows specifications of the time measurement function. Tables 21.5 and 21.6 list pin settings of the time
measurement function. Figures 21.13 and 21.14 show operation examples of the time measurement function. Figure 21.15 shows an operation example of the prescaler function and gate function.
Table 21.4 Time Measurement Function Specifications
Item
Specification
Measurement Channel
Channels 0 to 7
Trigger Input Polarity
Rising edge, falling edge and both edges of the INPC1j pin
Measurement Start Condition
The IFEj bit in the G1FE register is set to "1" (channel j function enabled)
while the FSCj bit (j=0 to 7) in the G1FS register is set to "1" (time
measurement function selected)
Measurement Stop Condition
The IFEj bit is set to "0" (channel j function disabled)
Time Measurement Timing
• No prescaler: every time a trigger signal is applied
• Prescaler (for channel 6 and channel 7):
every G1TPRk register (k=6,7) value +1 times a trigger signal is applied
Interrupt Request Generating Timing
The TM1jR bit in the interrupt request register (See Figure 10.14) is set to
"1" (interrupt requested) at time measurement timing
INPC1j Pin Function
Trigger input pin
Selectable Function
• Digital filter function
The digital filter samples a trigger input signal level every f1 or fBT1
cycles and passes pulse signals, matching trigger input signal level
three times
• Prescaler function (for channel 6 and channel 7)
Time measurement is executed every G1TPRk register value +1 times a
trigger signal is applied
• Gate function (for channel 6 and channel 7)
After time measurement by the first trigger input, trigger input cannot be
accepted. However, while the GOC bit in the G1TMCRk register is set to
"1" (gate cleared by matching the base timer with the G1POp register (p=4
when k=6, p=5 when k=7), trigger input can be accepted again by matching
the base timer value with the G1POp register setting or by setting the GSC
bit in the G1TMCRk register is set to "1"
Rev. 1.10 Oct. 18, 2005 Page 259 of 435
REJ09B0162-0110
21. Intelligent I/O (Time Measurement Function)
M32C/88 Group (M32C/88T)
Table 21.5 Pin Settings for Time Measurement Function
Pin
Bit and Setting
PS1, PS2, PS5, PS8 Registers PD7, PD8, PD11, PD14 Registers
P70/INPC16
PS1_0 = 0
PD7_0 = 0
P71/INPC17
PS1_1 = 0
PD7_1 = 0
P73/INPC10
PS1_3 = 0
PD7_3 = 0
P74/INPC11
PS1_4 = 0
PD7_4 = 0
P75/INPC12
PS1_5 = 0
PD7_5 = 0
P76/INPC13
PS1_6 = 0
PD7_6 = 0
P77/INPC14
PS1_7 = 0
PD7_7 = 0
P81/INPC15
PS2_1 = 0
PD8_1 = 0
P110/INPC10(1)
PS5_0 = 0
PD11_0 = 0
P111/INPC11(1)
PS5_1 = 0
PD11_1 = 0
P112/INPC12(1)
PS5_2 = 0
PD11_2 = 0
P113/INPC13(1)
PS5_3 = 0
PD11_3 = 0
P140/INPC14(1)
PS8_0 = 0
PD14_0 = 0
P141/INPC15(1)
PS8_1 = 0
PD14_1 = 0
P142/INPC16(1)
PS8_2 = 0
PD14_2 = 0
P143/INPC17(1)
PS8_3 = 0
PD14_3 = 0
IPS Register
IPS1 = 0
IPS1 = 1
NOTE:
1. This port is provided in the 144-pin package only.
Table 21.6 Time Measurement Function Associated Register Settings
Register
G1TMCRj
Bit
Function
CTS1, CTS0
Select a time measurement trigger
DF1, DF0
Select the digital filter function
GT, GOC, GSC
Select the gate function
PR
Select the prescaler function
G1TPRk
-
Setting value of the prescaler
G1FS
FSCj
Set to "1" (time measurement function)
G1FE
IFEj
Set to "1" (channel j function enabled)
j = 0 to 7
k = 6, 7
Bit configurations and functions vary with channels used.
Registers associated with the time measurement function must be set after setting registers associated with the base timer.
Rev. 1.10 Oct. 18, 2005 Page 260 of 435
REJ09B0162-0110
21. Intelligent I/O (Time Measurement Function)
M32C/88 Group (M32C/88T)
Signal Applied
to the INPC1j Pin
"H"
"L"
FFFF16
n
Base Timer
p
m
000016
G1TMj Register
m
n
p
Write "0" by program if setting to "0"
TM1jR Bit in the
IIOiIR Register
"1"
"0"
i= 0 to 4, 8 to 10
j= 0 to 7
The above applies under the following conditions:
The CTS1 and CTS0 bits in the G1TMCRj registers are set to "012" (rising edge).
The PR bit is set to "0" (no prescaler used) and the GT bit is set to "0" (no gate
function used).
The RST2 and RST1 bits in the G1BCR1 register are set to "002" (no base timer
reset).
The UD1 and UD0 bits are set to "002" (counter increment mode).
To set the base timer to "000016" (setting the RST1 bit to "1" and the RST2 bit to "0")
when the base timer value matches the G1PO0 register setting, the base timer is set
to "000016" after it reaches the G1PO0 register value +2.
Figure 21.13 Time Measurement Function (1)
Rev. 1.10 Oct. 18, 2005 Page 261 of 435
REJ09B0162-0110
21. Intelligent I/O (Time Measurement Function)
M32C/88 Group (M32C/88T)
(1) When selecting the rising edge as a time measurement trigger
(The CTS1 and CTS0 bits in the G1TMCRj register (j=0 to 7) are set to "012")
fBT1
Base timer
n-2
n-1
n
n+1
n+2
n+3
n+4
n+5
n+6
n+7
n+8
n+9 n+10 n+11 n+12 n+13 n+14
(Note 2)
INPC1j pin
"H"
"L"
"1"
TM1jR bit(1)
"0"
Write "0" by program
if setting to "0"
Delayed by max. 1 clock
G1TMj register
n
n+5
n+8
NOTES:
1. Bits in the IIO0IR to IIO4IR, IIO8IR to IIO10IR registers. See Figure 10.14 about the TM1jR bit.
2. Input pulse applied to the INPC1j pin requires 1.5 fBT1 clock cycles or more.
(2) When selecting both edges as a time measurement trigger
(The CTS1 and CTS0 bits are set to "112")
fBT1
Base timer
n-2
n-1
n
n+1
n+2
n+3
n+4
n+5
n+6
n+7
n+8
n+9 n+10 n+11 n+12 n+13 n+14
"H"
INPC1j pin
"L"
(Note 2)
"1"
TM1jR
bit(1)
"0"
Write "0" by program
if setting to "0"
G1TMj register
n
n+2
n+5
n+6
n+8
n+12
NOTES:
1. Bits in the IIO0IR to IIO4IR, IIO08IR to IIO10IR registers. See Figure 10.14 about the TM1jR bit.
2. No interrupt is generated if the microcomputer receives a trigger signal when the TM1jR bit is set to "1".
However, the value of the G1TMj register changes.
(3) Trigger signal when using the digital filter
(The DF1 and DF0 bits in the G1TMCRj register are set to "102" or "112")
f1 or fBT1(1)
"H"
INPC1j pin
Trigger signal
after passing
the digital filter
"L"
"H"
"L"
Maximum 3.5 f1 or
fBT1(1) clock cycles
Signal, which does not match
three times, is stripped off
The trigger signal is delayed
by the digital filter
NOTE:
1. fBT1 when the DF1 and DF0 bits are set to "102", and f1 when to "112".
Figure 21.14 Time Measurement Function (2)
Rev. 1.10 Oct. 18, 2005 Page 262 of 435
REJ09B0162-0110
21. Intelligent I/O (Time Measurement Function)
M32C/88 Group (M32C/88T)
(1) With the Prescaler Function
(When the G1TPRj register (j=6, 7) is set to "0216", the PR bit in the G1TMCRj register is set to "1")
fBT1
Base Timer
INPC1j pin input
n-2
n-1
n
n+1
n+2
n+3
n+4
n+5
n+6
n+7
n+8
n+9 n+10 n+11 n+12 n+13 n+14
"H"
"L"
"H"
Internal time
measurement trigger "L"
Prescaler(1)
TM1jR bit(2)
0
2
1
0
2
Write "0" by program
if setting to "0"
"1"
"0"
G1TMj register
n
n+12
NOTES:
1. This applies to cycles following the first cycle the G1TPRj register decrements after the PR bit in the G1TMCRj
register is set to "1" (prescaler used).
2. Bits in the IIO0IR to IIO4IR, IIO8IR to IIO10IR registers. See Figure 10.14 for the TM1jR bit.
(2) With the Gate Function
(The gate function is cleared by matching the base timer with the G1POk register (k=4, 5).
the GT bit in the G1TMCRj register is set to "1", the GOC bit is set to "1")
fBT1
FFFF16
Value of the G1POk register
Base Timer
000016
IFEj bit in G1FE
register
"1"
"0"
INPC1j pin input
"H"
"L"
Internal time
"H"
measurement trigger "L"
Signal to match
G1POk register
This trigger input is disabled
due to the gate function
"H"
"L"
Gate control signal
"H"
"L"
TM1jR bit(1)
"1"
Gate
Gate cleared
Write "0" by program if setting to "0"
"0"
G1TMj register
NOTE:
1. Bits in the IIO0IR to IIO4IR, IIO8IR to IIO10IR registers. See Figure 10.14 for the TM1jR bit.
Figure 21.15 Prescaler Function and Gate Function
Rev. 1.10 Oct. 18, 2005 Page 263 of 435
REJ09B0162-0110
Gate
21. Intelligent I/O (Waveform Generating Function)
M32C/88 Group (M32C/88T)
21.3 Waveform Generating Function
Waveforms are generated when the value of the base timer matches that of the G1POj register (j=0 to 7).
The waveform generating function has the following three modes :
• Single-phase waveform output mode
• Phase-delayed waveform output mode
• Set/Reset waveform output (SR waveform output) mode
Table 21.7 lists pin settings of the waveform generating function. Table 21.8 lists registers associated with
the waveform generating function.
Table 21.7 Pin Settings for Waveform Generating Function
Pin
PS1, PS2, PS5 to PS8
Registers
Bit and Setting
PSL1, PSL2 Registers
PSC, PSC2 Registers PSD1 Register
P70/OUTC16
PS1_0 = 1
PSL1_0 = 0
PSC_0 = 1
PSD1_0=1
P71/OUTC17
PS1_1 = 1
PSL1_1 = 0
PSC_1 = 1
PSD1_1=1
P73/OUTC10
PS1_3 = 1
PSL1_3 = 0
PSC_3 = 1
-
P74/OUTC11
PS1_4 = 1
PSL1_4 = 0
PSC_4 = 1
-
P75/OUTC12
PS1_5 = 1
PSL1_5 = 1
-
-
P76/OUTC13
PS1_6 = 1
PSL1_6 = 0
PSC_6 = 0
PSD1_6=1
P77/OUTC14
PS1_7 = 1
PSL1_7 = 1
-
-
P81/OUTC15
PS2_1 = 1
PSL2_1 = 1
PSC2_1=1
-
P110/OUTC10(1)
PS5_0 = 1
-
-
-
P111/OUTC11(1) PS5_1 = 1
P112/OUTC12(1) PS5_2 = 1
P113/OUTC13(1) PS5_3 = 1
P140/OUTC14(1) PS8_0 = 1
P141/OUTC15(1) PS8_1 = 1
P142/OUTC16(1) PS8_2 = 1
P143/OUTC17(1) PS8_3 = 1
NOTE:
1. This port is provided in the 144-pin package only.
Table 21.8 Waveform Generating Function Associated Register Settings
Register
G1POCRj
Bit
MOD2 to MOD0
IVL
RLD
INV
FSCj
IFEj
Function
Select waveform output mode
Select default output value
Select a timing to reload the value of the G1POj register
Select if output level is inversed
Select when output waveform is inversed
Set to "0" (waveform generating function)
Set to "1" (channel j function enabled)
G1POj
G1FS
G1FE
j = 0 to 7
Bit configurations and functions vary with channels used.
Registers associated with the waveform generating measurement function must be set after setting registers associated
with the base timer.
Rev. 1.10 Oct. 18, 2005 Page 264 of 435
REJ09B0162-0110
21. Intelligent I/O (Waveform Generating Function)
M32C/88 Group (M32C/88T)
21.3.1 Single-Phase Waveform Output Mode
Output signal level of the OUTC1j pin becomes high ("H") when the base timer value matches the G1POj
register (j=0 to 7) setting. The "H" signal switches to a low-level ("L") signal when the base timer reaches
"000016". If the IVL bit in the G1POCRj register is set to "1" ("H" output as default value), an "H" signal
output is provided when waveform output starts. If the INV bit is set to "1" (output inversed), the level of
the waveform output is inversed. See Figure 21.16 for details on single-phase waveform output mode
operation. Table 21.9 lists specifications of single-phase waveform output mode.
Table 21.9 Single-Phase Waveform Output Mode Specifications
Item
Specification
Output Waveform(2)
• Free-running operation
(the RST2 and RST1 bits in the G1BCR1 register are set to "002")
Cycle
:
"L" width
:
"H" width
:
65536
fBT1
m
fBT1
65536-m
fBT1
m : setting value of the G1POj register (j=0 to 7), 000016 to FFFF16
• The base timer is cleared to "000016" by matching the base timer with the
G1PO0 register (the RST1 bit is set to "1" and the RST2 bit is set to "0")
n+2
Cycle
:
fBT1
m
"L" width
:
fBT1
n+2-m
"H" width
:
fBT1
m : setting value of the G1POj register (j=1 to 7), 000016 to FFFF16
n : setting value of the G1PO0 register, 000116 to FFFD16
If m ≥ n+2, the output level is fixed to "L"
Waveform Output Start
Condition(1)
The IFEj bit in the G1FE register is set to "1" (channel j function enabled)
Waveform Output Stop Condition
The IFEj bit is set to "0" (channel j function disabled)
Interrupt Request
The PO1jR bit in the interrupt request register is set to "1" (interrupt
requested) when the base timer value matches the G1POj register setting.
(See Figure 10.14)
OUTC1j Pin
Pulse signal output pin
Selectable Function
• Default value set function: Set starting waveform output level
• Inversed output function:
Waveform output signal is inversed and provided from the OUTC1j pin
NOTES:
1. Set the FSCj bit in the G1FS register to "0" (waveform generating function selected).
2. When the INV bit in the G1POCRj register is set to "1" (output inversed), the "L" width and "H" width are inversed.
Rev. 1.10 Oct. 18, 2005 Page 265 of 435
REJ09B0162-0110
21. Intelligent I/O (Waveform Generating Function)
M32C/88 Group (M32C/88T)
(1) Free-Running Operation
(The RST2 and RST1 bits in the G1BCR1 register are set to "002")
FFFF16
Base Timer
m
000016
m
fBT1
OUTC1j pin(1)
"H"
"L"
OUTC1j pin(2)
PO1jR bit in the
IIOiIR register
65536-m
fBT1
65536
fBT1
"H"
"L"
Write "0" by program
if setting to "0"
"1"
"0"
i=0 to 4, 8 to 10; j=0 to 7
m: Setting value of the G1POj register, 000016 to FFFF16
NOTES:
1. Waveform output when the INV bit in the G1POCRj register is set to "0" (not inversed)
and the IVL bit in the G1POCRi register is set to "0" (output "L" as default value).
2. Waveform output when the INV bit is set to "0" (not inversed) and the IVL bit is set
to "1" ("H" output as default value).
The above applies under the following condition:
• The RST2 and RST1 bits in the G1BCR1 register are set to "002" (no base timer reset
and the UD1 and UD0 bits in the G1BCR1 register to "002" (counter increment mode).
(2) The Base Timer is Reset by Matching the Base Timer with the G1PO0 Registe
(The RST1 bit is set to "1" and the RST2 bit is set to "0")
n+2
Base Timer
m
000016
m
fBT1
n+2-m
fBT1
"H"
OUTC1j pin
"L"
n+2
fBT1
PO1jR bit in the
IIOiIR register
"1"
"0"
Write "0" by
program if
setting to "0"
i=0 to 4, 8 to 10; j=1 to 7
m: Setting value of the G1POj register, 000016 to FFFF16
n: Setting value of the G1PO0 register, 000116 to FFFD16
The above applies under the following conditions:
• The IVL bit in the G1POCRj register is set to "0" ("L" output as default value) and
the INV bit is set to "0" (not inversed).
• The UD1 and UD0 bits are set to "002" (counter increment mode).
• m<n+2
Figure 21.16 Single-Phase Waveform Output Mode
Rev. 1.10 Oct. 18, 2005 Page 266 of 435
REJ09B0162-0110
21. Intelligent I/O
M32C/88 Group (M32C/88T)
21.3.2 Phase-Delayed Waveform Output Mode
Output signal level of the OUTC1j pin is inversed every time the base timer value matches the G1POj
register (j=0 to 7) setting. Table 21.10 lists specifications of phase-delayed waveform output mode.
Figure 21.17 lists an example of phase-delayed waveform output mode operation.
Table 21.10 Phase-Delayed Waveform Output Mode Specifications
Item
Output Waveform
Specification
• Free-running operation
(the RST2 and RST1 bits in the G1BCR1 register are set to "002")
Cycle
"H" and "L" widths
65536 x 2
fBT1
65536
:
fBT1
:
Setting value of the G1POj (j=0 to 7) register is 000016 to FFFF16
• The base timer is cleared to "000016" by matching the base timer with the
G1PO0 register (the RST1 bit is set to "1" and the RST2 bit is set to "0")
2(n+2)
Cycle
:
fBT1
n+2
"H" and "L" widths :
fBT1
n : setting value of the G1PO0 register, 000116 to FFFD16
Setting value of the G1POj (j=1 to 7) register is 000016 to FFFF16
If G1POj register ≥ n+2, the output level is not inversed
Waveform Output Start Condition(1) The IFEj bit (j=0 to 7) in the G1FE register is set to "1" (channel j function
enabled)
Waveform Output Stop Condition
The IFEj bit is set to "0" (channel j function disabled)
Interrupt Request
The PO1jR bit in the interrupt request register is set to "1" (interrupt
requested) when the base timer vslur matches the G1POj register setting.
(See Figure 10.14)
OUTC1j Pin
Pulse signal output pin
Selectable Function
• Default value set function: Set starting waveform output level
• Inversed output function
Waveform output level is inversed to output a waveform from the OUTC1j pin
NOTE:
1. Set the FSCj bit in the G1FS register to "0" (waveform generating function selected).
Rev. 1.10 Oct. 18, 2005 Page 267 of 435
REJ09B0162-0110
21. Intelligent I/O
M32C/88 Group (M32C/88T)
(1) Free-Running Operation
(The RST2 and RST1 bits in the G1BCR1 register are set to "002")
FFFF16
Base Timer
m
000016
65536
fBT1
65536
fBT1
"H"
OUTC1j pin(1)
OUTC1j pin(2)
PO1jR bit in the
IIOiIR register
Inverse
Inverse
"L"
"H"
65536 x 2
fBT1
Inverse
Inverse
"L"
Write "0" by program
if setting to "0"
"1"
"0 "
i=0 to 4, 8 to 10; j=0 to 7
m: Setting value of the G1POj register, 000016 to FFFF16
NOTES:
1. Waveform output when the INV bit in the G1POCRj register is set to "0" (not inversed)
and the IVL bit in the G1POCRj register is set to "0" ("L" output as default value).
2. Waveform output when the INV bit is set to "0" (not inversed) and the IVL bit is set to "1"
("H" output as default value).
The above applies under the following condition:
• The RST2 and RST1 bits in the G1BCR1 register are set to "002" (no base timer reset)
and the UD1 and UD0 bits in the G1BCR1 register to "002" (counter increment mode).
(2) The Base Timer is Reset when the Base Timer Matches the G1PO0 Register
(The RST1 bit is set to "1" and the RST2 bit is set to "0")
n+2
Base Timer
m
000016
m
fBT1
"H"
"L"
OUTC1j pin
PO1jR bit in the
IIOiIR register
"1"
n+2
fBT1
Inverse
Write "0" by
program if
setting to "0"
n+2
fBT1
Inverse
Inverse
2(n+2)
fBT1
"0"
i=0 to 4, 8 to 10; j=1 to 7
m: Setting value of the G1POj register, 000016 to FFFF16
n: Setting value of the G1PO0 register, 000116 to FFFD16
The above applies under the following conditions:
• The IVL bit in the G1POCRj register is set to "0" ("L" output as default value) and
the INV bit is set to "0" (not inversed).
• The UD1 and UD0 bits are set to "002" (counter increment mode).
• m<n+2
Figure 21.17 Phase-delayed Waveform Output Mode
Rev. 1.10 Oct. 18, 2005 Page 268 of 435
REJ09B0162-0110
21. Intelligent I/O (Waveform Generating Function)
M32C/88 Group (M32C/88T)
21.3.3 Set/Reset Waveform Output (SR Waveform Output) Mode
Output signal level of the OUTC1j pin becomes high ("H") when the base timer value matches the G1POj
register (j=0, 2, 4, 6) setting. The "H" signal switches to a low-level ("L") signal when the base timer value
matches the G1POk register (k=j+1) setting or when the base timer is set to "000016". If the IVL bit in the
G1POCRj register is set to "1" ("H" output as default value), an "H" signal output is provided when waveform output starts. If the INV bit is set to "1" (output inversed), the level of the output waveform is inversed.
Table 21.11 lists specifications of SR waveform output mode. Figure 21.18 shows an example of a SR
waveform output mode operation.
Table 21.11 SR Waveform Output Mode Specifications
Item
Output Waveform(2)
Specification
• Free-running operation
(the RST2 and RST1 bits in the G1BCR1 register are set to "002")
(1) m < n
"H" width
:
"L" width
:
n-m
fBT1
m (3)
fBT1
+
65536 - n(4)
fBT1
(2) m ≥ n
: 65536 - m
fBT1
m
"L" width :
fBT1
m : setting value of the G1POj register (j=0, 2, 4, 6 )
"H" width
n : setting value of the G1POk register (k=j+1)
• The base timer is cleared to "000016" by matching the base timer with the
G1PO0 register(1) (the RST1 bit is set to "1" and the RST2 bit is set to "0")
(1) m < n < p+2
"H" width
:
"L" width
:
n-m
fBT1
m (3)
fBT1
+
p + 2 - n(4)
fBT1
(2) m < p+2 ≤ n
"H" width
"L" width
: p+2-m
fBT1
m
:
fBT1
(3) If m ≥ p+2, the output level is fixed to "L"
m : setting value of the G1POj register (j=2, 4, 6), 000016 to FFFF16
n : setting value of the G1POk register (k=j+1), 000016 to FFFF16
p : setting value of the G1PO0 register, 000116 to FFFD16
NOTES:
1. When the G1PO0 register resets the base timer, the channel 0 and 1 SR waveform generating functions are not
available.
2. When the INV bit in the G1POCRj register is set to "1" (output inversed), the "L" width and "H" width are inversed.
3. Waveform from base timer reset until when output level becomes "H".
4. Waveform from when output level becomes "L" until base timer reset.
Rev. 1.10 Oct. 18, 2005 Page 269 of 435
REJ09B0162-0110
21. Intelligent I/O (Waveform Generating Function)
M32C/88 Group (M32C/88T)
Table 21.11 SR Waveform Output Mode Specifications (Continued)
Item
Specification
Waveform Output Start Condition(5) The IFEq bit (q=0 to 7) in the G1FE register is set to "1" (channel q function
enabled)
Waveform Output Stop Condition
The IFEq bit is set to "0" (channel q function disabled)
Interrupt Request
The PO1jR bit in the interrupt request register is set to "1" (interrupt requested)
when the value of the base timer matches that of the G1POj register.
The PO1kR bit in the interrupt request register is set to "1" (imterrupt requested)
when the value of the base timer matches that of the G1POk register. (See
Figure 10.14)
OUTC1j Pin
Pulse signal output pin
Selectable Function
• Default value set function: Set starting waveform output level
• Inversed output function
Waveform output level is inversed to provide a waveform from the OUTC1j pin
NOTE:
5. Set the FSCj bit in the G1FS register to "0" (waveform generating function selected).
Rev. 1.10 Oct. 18, 2005 Page 270 of 435
REJ09B0162-0110
21. Intelligent I/O (Waveform Generating Function)
M32C/88 Group (M32C/88T)
(1) Free-Running Operation
(The RST2 to RST0 bits in the G1BCR1 register are set to "002")
FFFF16
n
Base Timer
m
000016
n-m
fBT1
"H"
OUTC1j pin(1)
OUTC1j
65536-n+m
fBT1
"L"
65536
fBT1
"H"
pin(2)
"L"
PO1jR bit in the
IIOiIR register
"1"
PO1kR bit in the
IIOiIR register
"1"
Write "0" by program
if setting to "0"
"0"
Write "0" by program
if setting to "0"
"0"
i=0 to 4, 8 to 10; j=0, 2, 4, 6; k=j+1
m: Setting value of the G1POj register, 000016 to FFFF16
n: Setting value of the G1POk register, 000016 to FFFF16
NOTES:
1. Waveform output when the INV bit in the G1POCRj register is set to "0" (not inversed)
and the IVL bit in the G1POCRj register is set to "0" (output "L" as default value).
2. Waveform output when the INV bit is set to "0" (not inversed) and the IVL bit is set to "1"
("H" output as default value).
The above applies under the following conditions:
• The RST2 and RST1 bits in the G1BCR1 register are set to "002" (no base timer reset)
and the UD1 and UD0 bits in the G1BCR1 register to "002" (counter increment mode).
• m<n
(2) The Base Timer is Reset when the Base Timer Matches the G1PO0 Register
(The RST1 bit is set to "1" and the RST2 bit is set to "0")
p+2
n
Base timer
m
000016
OUTC1j pin
n-m
fBT1
p+2-n+m
fBT1
"H"
"L"
PO1jR bit in the "1"
IIOiIR register "0"
PO1kR bit in the "1"
IIOiIR register "0"
p+2
fBT1
Write "0" by program
if setting to "0"
Write "0" by program
if setting to "0"
i=0 to 4, 8 to 10; j=2, 4, 6; k=j+1
m: Setting value of the G1POj register, 000016 to FFFF16
n: Setting value of the G1POk register, 000016 to FFFF16
p: Setting value of the G1PO0 register, 000116 to FFFD16
The above applies under the following conditions:
• The IVL bit in the G1POCRj register is set to "0" ("L" output as default value) and
the INV bit is set to "0" (not inversed).
• The UD1 and UD0 bits are set to "002" (counter increment mode).
• m<n<p+2
Figure 21.18 SR Waveform Output Mode
Rev. 1.10 Oct. 18, 2005 Page 271 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
21.4 Communication Unit 0 and 1 Communication Function
In the intelligent I/O communication unit 1, 8-bit clock synchronous serial I/O, 8-bit clock asynchronous
serial I/O (UART) or HDLC data processing is available. In the communication unit 0, 8-bit clock synchronous serial I/O or HDLC data processing is available.
Figures 21.19 to 21.28 show registers associated with the communication function.
Receive Input Register i (i=0,1)
b7
b0
Symbol
Address
00EC16, 012C16
G0RI, G1RI
Function
Set data to be transmitted to a received
data generation circuit
After Reset
Indeterminate
Setting Range
RW
0016 to FF16
WO
Transmit Output Register i (i=0,1)
b7
b0
Symbol
Address
After Reset
G0TO, G1TO
00EE16, 012E16
Indeterminate
Function
Can read a data transmitted by a transmitted data generation circuit
Figure 21.19 G0RI and G1RI Registers, G0TO and G1TO Registers
Rev. 1.10 Oct. 18, 2005 Page 272 of 435
REJ09B0162-0110
RW
RO
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
SI/O Communication Control Register i (i=0, 1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
00EF16, 012F16
G0CR, G1CR
Bit
Symbol
TI
Bit Name
Transmit Buffer
Empty Flag
Transmit Register
TXEPT
Empty Flag
RI
After Reset
0000 X0112
Receive Complete
Flag
Function
RW
0: Data in the GiTB register
1: No data in the GiTB register
RO
0: Data in the transmit register
(during transmission)
1: No data in the transmit register
(transmit completed)
RO
0: No data in the GiRB register
1: Data in the GiRB register
RO
(b3)
Nothing is assigned. When write, set to "0".
When read, its contents is indeterminate.
TE
Transmit Enable Bit
0: Transmit disabled
1: Transmit enabled
RW
RE
Receive Enable Bit
0: Receive disabled
1: Receive enabled
RW
IPOL
ISRxD Input Polarity 0: No inverse
1: Inverse(1)
Switch Bit
RW
OPOL
ISTxD Output Polarity 0: No inverse
1: Inverse(1)
Switch Bit
RW
NOTE:
1. Set this bit to "1" when using UART mode.
SI/O Receive Buffer Register i (i=0, 1)
b15
b8 b7
b0
Symbol
G0RB, G1RB
Bit
Symbol
Address
00E916-00E816, 012916-012816
Bit Name
After Reset
X000 XXXX XXXX XXXX2
Function
Received data
(b7 - b0)
RW
RW
Nothing is assigned.
(b11 - b8) When read, its content is indeterminate.
OER
Overrun Error Flag
0: No overrun error
1: Overrun error found
RO
FER
Framing Error Flag(1)
0: No framing error
1: Framing error found
RO
PER
Parity Error Flag(1)
0: No parity error
1: Parity error found
RO
(b15)
Nothing is assigned.
When read, its content is indeterminate.
NOTE:
1. Nothing is assigned in the FER and PER bits in the G0RB register.
When read, its content is indeterminate.
Figure 21.20 G0CR and G1CR Registers, G0RB and G1RB Registers
Rev. 1.10 Oct. 18, 2005 Page 273 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
SI/O Communication Mode Register 0
b7
b6
b5
b4
b3
b2
b1
b0
0 0 0
Symbol
Address
After Reset
G0MR
00ED16
0016
Bit
Symbol
Bit Name
Function
b1b0
GMD0
Communication Mode
Select Bit
RW
0 1 : Clock synchronous serial I/O
mode
1 1 : HDLC data processing mode(1) RW
Internal/External Clock
Select Bit
0: Internal clock
1: External clock
RW
Reserved Bit
Set to "0"
RW
Transfer Format
Select Bit
0: LSB first
1: MSB first
RW
Transmit Interrupt
Cause Select Bit
0: No data in the G0TB register
(TI=1)
1: Transmission is completed
(TXEPT=1)
RW
GMD1
CKDIR
(b5 - b3)
UFORM
IRS
RW
NOTE:
1. Do not set to any bit combinations except the above.
SI/O Communication Mode Register 1
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
012D16
G1MR
Bit
Symbol
After Reset
0016
Bit Name
Function
RW
b1b0
GMD0
Communication Mode
Select Bit
GMD1
0 0 : UART mode
RW
0 1 : Clock synchronous serial I/O
mode
1 0 : Special communication mode(1) RW
1 1 : HDLC data processing mode
CKDIR
Internal/External Clock
Select Bit
0 : Internal clock
1 : External clock
RW
STPS
Stop Bit Length
Select Bit
0: 1 stop bit
1: 2 stop bits
RW
PRY
Parity Odd/Even
Select Bit
0: Odd parity
1: Even parity
RW
Parity Enable
Select Bit
0: Parity disabled
1: Parity enabled
RW
Transfer Format
Select Bit
0: LSB first
1: MSB first
RW
Transmit Interrupt
Cause Select Bit
0: No data in the G1TB register
(TI=1)
1: Transmission is completed
(TXEPT=1)
RW
PRYE
UFORM
IRS
NOTE:
1. In M32C/88, do not set the GMD1 and GMD0 bits to "102" except when using in motor vehicles.
Figure 21.21 G0MR and G1MR Registers
Rev. 1.10 Oct. 18, 2005 Page 274 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
SI/O Expansion Mode Register 0(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
G0EMR
0
Address
00FC16
Bit
Symbol
After Reset
0016
Bit Name
Function
RW
Reserved Bit
Set to "0"
RW
CRCV
CRC Default Value
Select Bit
0: Set to "000016"
1: Set to "FFFF16"
RW
ACRC
CRC Reset Select Bit
0: Not reset
1: Reset(2)
RW
BSINT
Bit Stuffing Error
Interrupt Select Bit
0: Not used
1: Used
RW
RXSL
Receive Source
Switch Bit
0: ISRxD0 pin
1: G0RI register
RW
TXSL
Transmit Source
Switch Bit
0: ISTxD0 pin
1: G0TO register
RW
(b0)
b7 b6
CRC0
CRC Generation
Polynomial Select Bit
CRC1
0
0
1
1
0 : X8+X4+X+1
1 : Do not set to this value
0 : X16+X15+X2+1
1 : X16+X12+X5+1
RW
RW
NOTES:
1. The G0EMR register is used in HDLC data processing mode. It must be in a reset state or set to
"0016" in clock synchronous serial I/O mode.
2. CRC is reset when data in the G0CMP3 register matches received data.
SI/O Expansion Mode Register 1(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
G1EMR
Bit
Symbol
Address
013C16
After Reset
0016
Bit Name
Function
RW
SMODE
Synchronous Mode
Select Bit
0: Re-synchronous mode not used
1: Re-synchronous mode
RW
CRCV
CRC Default Value
Select Bit
0: Set to "000016"
1: Set to "FFFF16"
RW
ACRC
CRC Reset Select Bit
0: Not reset
1: Reset(2)
RW
BSINT
Bit Stuffing Error
Interrupt Select Bit
0: Not used
1: Used
RW
RXSL
Receive Source
Switch Bit
0: ISRxD1 pin
1: G1RI register
RW
TXSL
Transmit Source
Switch Bit
0: ISTxD1 pin
1: G1TO register
RW
b7 b6
CRC0
CRC Generation
Polynomial Select bit
CRC1
0
0
1
1
0 : X8+X4+X+1
1 : Do not set to this value
0 : X16+X15+X2+1
1 : X16+X12+X5+1
NOTES:
1. The G1EMR register is used in special communication mode or HDLC data processing mode. It
must be in a reset state or be set to "0016" in clock synchronous serial I/O mode or UART mode.
2. CRC is reset when data in the G1CMP3 register matches received data.
Figure 21.22 G0EMR and G1EMR Registers
Rev. 1.10 Oct. 18, 2005 Page 275 of 435
REJ09B0162-0110
RW
RW
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
SI/O Expansion Transmit Control Register 0(1)
b7
b6
b5
b4
b3
b2
b1
b0
0 0 0 0
0
Symbol
Address
After Reset
G0ETC
00FF16
0000 0XXX2
Bit
Symbol
Bit Name
Function
RW
Reserved Bit
Set to "0"
Transmit CRC
Enable Bit
0: Not used
1: Used
RW
Reserved Bit
Set to "0"
RW
TBSF0
Transmit Bit Stuffing "1"
Insert Select Bit
0: "1" is not inserted
1: "1" is inserted
RW
TBSF1
Transmit Bit Stuffing "0"
Insert Select Bit
0: "0" is not inserted
1: "0" is inserted
RW
(b3 - b0)
TCRCE
(b5)
NOTE:
1. The G0ETC register is used in HDLC data processing mode. It must be in a reset state or set to
"0016" in clock synchronous serial I/O mode.
SI/O Expansion Transmit Control Register 1(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
G1ETC
Bit
Symbol
(b2 - b0)
Address
013F16
After Reset
0000 0XXX2
Bit Name
Reserved Bit
Function
When read,
its content is indeterminate
RW
RO
SOF
SOF Transmit
Request Bit
0: Not requested to transmit SOF
1: Requested to transmit SOF
RW
TCRCE
Transmit CRC
Enable Bit
0: Not used
1: Used
RW
ABTE
Arbitration Enable Bit
0: Not used
1: Used
RW
TBSF0
Transmit Bit Stuffing "1" 0: "1" is not inserted
1: "1" is inserted
Insert Select Bit
RW
TBSF1
Transmit Bit Stuffing "0" 0: "0" is not inserted
1: "0" is inserted
Insert Select Bit
RW
NOTE:
1. The G1ETC register is used in special communication mode or HDLC data processing mode. It
must be in a reset state or set to "0016" in clock synchronous serial I/O mode or UART mode.
Figure 21.23 G0ETC and G1ETC Registers
Rev. 1.10 Oct. 18, 2005 Page 276 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
SI/O Expansion Receive Control Register i (i=0,1)(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
G0ERC, G1ERC
Bit
Symbol
CMP0E
CMP1E
Address
00FD16, 013D16
Bit Name
After Reset
0016
Function
RW
Data Compare 0: The GiDR register (receive data register)
is not compared with the GiCMP0 register
RW
Function 0
1: The GiDR register is compared with the
Select Bit
GiCMP0 register
Data Compare 0: The GiDR register (receive data register)
is not compared with the GiCMP1 register
RW
Function 1
1: The GiDR register is compared with the
Select Bit
GiCMP1 register
CMP2E
Data Compare
Function 2
Select Bit
CMP3E
Data Compare
Function 3
Select Bit
0: The GiDR register (receive data register)
is not compared with the GiCMP2 register
RW
1: The GiDR register is compared with the
GiCMP2 register
0: The GiDR register (receive data register)
is not compared with the GiCMP3 register RW
1: The GiDR register is compared with the
GiCMP3 register(2)
RCRCE
Receive CRC
Enable Bit
0: Not used
1: Used
RW
Receive Shift
Operation
Enable Bit
Receive Bit
Stuffing "1" Delete
Select Bit
Receive Bit
Stuffing "0" Delete
Select Bit
0: Receive shift operation disabled
1: Receive shift operation enabled
RW
0: "1" is not deleted
1: "1" is deleted
RW
0: "0" is not deleted
1: "0" is deleted
RW
RSHTE
RBSF0
RBSF1
NOTES:
1. The GiERC register is used in special communication mode or HDLC data processing mode.
It must be set to "0010 00002" in clock synchronous serial I/O mode.
It must be in a reset state or be set to "0016" in UART mode.
2. When the ACRC bit in the GiEMR register is set to "1" (CRC reset function used), set the CMP3E bit
to "1".
Figure 21.24 G0ERC and G1ERC Registers
Rev. 1.10 Oct. 18, 2005 Page 277 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
SI/O Special Communication Interrupt Detect Register 0 (1, 2)
b7
b6
b5
b4
b3
0
b2
b1
b0
0 0
Symbol
Address
00FE16
G0IRF
Bit
Symbol
Bit Name
Reserved Bit
(b1 - b0)
After Reset
0016
Function
Set to "0"
RW
RW
Bit Stuffing Error 0: Not detected
Detect Flag
1: Detected
RW
Reserved Bit
Set to "0"
RW
IRF0
Interrupt Cause
Determination
Flag 0
IRF1
Interrupt Cause
Determination
Flag 1
IRF2
Interrupt Cause
Determination
Flag 2
IRF3
Interrupt Cause
Determination
Flag 3
0: The G0DR register (receive data register)
does not match the G0CMP0 register
1: The G0DR register matches the G0CMP0
register
0: The G0DR register (receive data register)
does not match the G0CMP1 register
1: The G0DR register matches the G0CMP1
register
0: The G0DR register (receive data register)
does not match the G0CMP2 register
1: The G0DR register matches the G0CMP2
register
0: The G0DR register (receive data register)
does not match the G0CMP3 register
1: The G0DR register matches the G0CMP3
register
BSERR
(b3)
RW
RW
RW
RW
NOTES:
1. The G0IRF register is used in HDLC data processing mode. Do not use in clock synchronous serial
I/O mode.
2. The SRT0R bit in the IIO4IR register is set to "1" if the BSERR or IRF0 to IRF3 bit is set to "1".
Figure 21.25 G0IRF Register
Rev. 1.10 Oct. 18, 2005 Page 278 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
SI/O Special Communication Interrupt Detect Register 1(1,2)
b7
b6
b5
b4
b3
b2
b1
b0
0 0
Symbol
Address
After Reset
G1IRF
013E16
0016
Bit
Symbol
(b1 - b0)
BSERR
Bit Name
Reserved Bit
Function
RW
RW
Set to "0"
Bit Stuffing Error 0 : Not detected
1 : Detected
Detect Flag
RW
RW
ABT
Arbitration Lost
Detect Flag
0 : Not detected
1 : Detected
IRF0
Interrupt Cause
Determination
Flag 0
IRF1
Interrupt Cause
Determination
Flag 1
IRF2
Interrupt Cause
Determination
Flag 2
IRF3
Interrupt Cause
Determination
Flag 3
0: The G1DR register (receive data register)
does not match the G1CMP0 register
1: The G1DR register (receive data register)
matches the G1CMP0 register
0: The G1DR register (receive data register)
does not match the G1CMP1 register
1: The G1DR register (receive data register)
matches the G1CMP1 register
0: The G1DR register (receive data register)
does not match the G1CMP2 register
1: The G1DR register (receive data register)
matches the G1CMP2 register
0: The G1DR register (receive data register)
does not match the G1CMP3 register
1: The G1DR register (receive data register)
matches the G1CMP3 register
RW
RW
RW
RW
NOTES:
1. The G1IRF register is used in special communication mode or HDLC data processing mode. It must
be in a reset state or set to "0016" in clock synchronous serial I/O mode or UART mode.
2. The SRT1R bit in the IIO4IR register is also set to "1" if the BSERR, ABT, or IRF0 to IRF3 bit is set to "1".
Transmit Buffer (Receive Data) Register i (i=0,1)
b7
b0
Symbol
G0TB, G0DR
G1TB, G1DR
Address
00EA16
012A16
After Reset
Indeterminate
Indeterminate
Function
RW
Set data to be transmitted.
In HDLC data processing mode, the receive data register is read by
reading the GiTB register. Value is written to the transmit buffer register
by writing it to the GiTB register. In HDLC data processing mode, the
value set in the GiRI register is transferred to the GiDR register.
RW
Figure 21.26 G1IRF Register, G0TB and G1TB / G0DR and G1DR Registers
Rev. 1.10 Oct. 18, 2005 Page 279 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
Data Compare Register ij (i=0,1, j=0 to 3)
b7
b0
Symbol
Address
After Reset
G0CMP0 to G0CMP3
G1CMP0 to G1CMP3
00F016, 00F116, 00F216, 00F316
013016, 013116, 013216, 013316
Indeterminate
Indeterminate
Function
Setting Range
RW
0016 to FF16
RW
Data to be compared
NOTE:
1. Set the GiMSK0 register to use the GiCMP0 register.
Set the GiMSK1 register to use the GiCMP1 register.
Data Mask Register ij (i=0,1, j=0,1)
b7
b0
Symbol
G0MSK0, G0MSK1
G1MSK0, G1MSK1
Address
00F416, 00F516
After Reset
Indeterminate
013416, 013516
Indeterminate
Function
Setting Range
RW
0016 to FF16
RW
Masked data for received data
Set incomparable bit to "1"
Transmit CRC Code Register i (i=0,1)
b15
b8 b7
b0
Symbol
G0TCRC, G1TCRC
Address
00FB16-00FA16, 013B16-013A16
After Reset
000016
Function
RW
Result of the transmit CRC calculation(1, 2)
RO
NOTES:
1. The calculated result is reset by setting the TE bit in the GiCR register to "0" (transmit disabled).
The CRCV bit in the GiEMR register selects a default value.
2. Transmit CRC calculation is performed with each bit of data transmitted while the TCRCE bit in
the GiETC register is set to "1" (used).
Receive CRC Code Register i (i=0,1)
b15
b8 b7
b0
Symbol
G0RCRC, G1RCRC
Address
00F916-00F816, 013916-013816
After Reset
Indeterminate
Function
RW
Result of the receive CRC calculation(1, 2, 3)
RO
NOTES:
1. The calculated result is reset by setting the RCRCE bit in the GiERC register to "0" (not used).
If the ACRC bit in the GiEMR register is set to "1" (reset), the result is reset by matching data in the
GiCMPj register (j=0 to 3) with the received data.
2. The result is reset to the default value selected by the CRCV bit in the GiEMR register before
reception starts.
3. Receive CRC calculation is performed with every bit of data received while the RCRCE bit in the
GiERC register is set to "1" (used).
Figure 21.27 G0CMP0 to G0CMP3 Registers and G1CMP0 to G1CMP3 Registers
G0MSK0 and G0MSK1 Registers, G1MSK0 and G1MSK1 Registers
G0TCRC and G1TCRC Registers, G0RCRC and G1RCRC Registers
Rev. 1.10 Oct. 18, 2005 Page 280 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
Communication Clock Select Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
00F616
CCS
Bit
Symbol
Bit Name
After Reset
XXXX 00002
Function
RW
b1 b0
CCS0
CCS1
Communication
Unit 0 Clock
Select Bit
0
0
1
1
0 : Do not set to this value
1 : f1(1)
0 : f2n
1 : f8
RW
RW
b3 b2
CCS2
CCS3
Communication
Unit 1 Clock
Select Bit
0
0
1
1
0 : Clock output from the channel i (i=1 to 3) RW
1 : f1(1)
0 : f2n
RW
1 : f8
Nothing is assigned. When write, set to "0".
(b7 - b4) When read, its contents is indeterminate.
NOTE:
1. This setting is enabled in HDLC data processing mode. Do not set the CCS1 and CC0 bits or
CCS3 and CCS2 bits to "012" in other modes.
Figure 21.28 CCS Register
Rev. 1.10 Oct. 18, 2005 Page 281 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
21.4.1 Clock Synchronous Serial I/O Mode (Communication Units 0 and 1)
In clock synchronous serial I/O mode, data is transmitted and received with the transfer clock. f8 or f2n
can be selected as the communication unit 0 transfer clock. f8, f2n or the clock generated in channels 0
and 3 can be selected as the communication unit 1 transfer clock.
Table 21.12 lists specifications of clock synchronous serial I/O mode for the communication units 0 and
1. Tables 21.13 and 21.14 list clock settings. Table 21.15 lists register settings. Tables 21.16 to 21.19
list pin settings. Figure 21.29 shows an example of transmit and receive operation.
Table 21.12 Clock Synchronous Serial I/O Mode Specifications (Communication Units 0 and 1)
Item
Specification
Transfer Data Format
Transfer Clock(1)
Transfer data :
8 bits long
See Tables 21.13 and 21.14
Transmit Start Condition
Set registers associated with the waveform generating function, the GiMR and GiERC
registers (i=0,1). Then, set as is written below after at least one transfer clock cycle.
• Set the TE bit in the GiCR register to "1" (transmit enabled)
• Set the TI bit in the GiCR register to "0" (data in the GiTB register)
Set registers associated with the waveform generating function, the GiMR and GiERC
registers. Then, set as is written below after at least one transfer clock cycle.
• Set the RE bit in the GiCR register to "1" (receive enabled)
• Set the TE bit to "1" (transmit enabled)
• Set the TI bit to "0" (data in the GiTB register)
Receive Start Condition
Interrupt Request
• While transmitting, one of the following conditions can be selected to set the SIOiTR
bit to "1" (interrupt requested) (see Figure 11.14) :
_ The IRS bit in the GiMR register is set to "0" (no data in the GiTB register) and
data is transferred to the transmit register from the GiTB register
_ The IRS bit is set to "1" (transmission completed) and data transfer from the
transmit register is completed
• While receiving, the following condition can be selected to set SIOiRR bit is set to "1"
(data reception is completed):
Data is transferred from the receive register to the GiRB register
Error Detection
Overrun error(2)
This error occurs, when the next data reception is started and the 8th bit of the next
data is received before reading the GiRB register
Selectable Function
• LSB first or MSB first
Select either bit 0 or bit 7 to transmit or receive data
• ISTxDi and ISRxDi I/O polarity inverse
ISTxDi pin output level and ISRxDi pin input level are inversed
NOTES:
1. In clock synchronous serial I/O mode, set the RSHTE bit in the GiERC register (i=0, 1) to "1" (receive
shift operation enabled).
2. When an overrun error occurs, the GiRB register is indeterminate.
When the OPOL bit in the GiCR register is set to "0" (ISTxD output polarity not inversed), the ISTxDi pin
puts in a high-level ("H") signal output after selecting operating mode until transfer starts. When the OPOL
bit is set to "1" (ISTxD output polarity inversed), the ISTxDi pin puts in a low-level ("L") signal output.
Table 21.13 Clock Settings (Communication Unit 0)
Transfer Clock
f8
f2n(1)
Input from ISCLK0
G0MR Register
CKDIR Bit
0
0
1
CCS Register
CCS0 Bit
CCS1 Bit
1
1
0
1
-
NOTE:
1. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Rev. 1.10 Oct. 18, 2005 Page 282 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
Table 21.14 Clock Settings (Communication Unit 1)
Transfer Clock(3)
G1MR Register
CKDIR Bit
(1)
fBT1
2(n+2)
f8
f2n(2)
Input from ISCLK1
CCS Register
CCS2 Bit
CCS3 Bit
0
0
0
0
0
1
1
0
-
1
1
-
n: Setting value of the G1PO0 register, 000116 to FFFD16
NOTES:
1. The transfer clock is generated in phase-delayed waveform output mode of the channel 3 waveform
generating function.
2. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
3. The transfer clock must be fBT1 divided by six or more.
Table 21.15 Register Settings in Clock Synchronous Serial I/O Mode (Communication Units 0 and 1)
Register
CCS
G1BCR0(2)
G1BCR1(2)
G1POCR0(2)
G1POCR1(2)
G1POCR3(2)
G1PO0(2)
G1PO3(2)
G1FS(2)
G1FE(2)
GiERC
GiMR
GiCR
GiTB
GiRB
Bit
Function
Communication Unit 1
Communication Unit 0
CCS1, CCS0
Setting not required when using the
Select transfer clock
communication unit 1 only
CCS3, CSS2
Select transfer clock
Setting not required when using the
BCK1, BCK0
Set to "112" (f1)
communication unit 0 only
DIV4 to DIV0
Select divide ratio of count source
IT
Set to "0"
7 to 0
Set to "0001 00102"
7 to 0
Set to "0000 01112"
7 to 0
Set to "0000 01112"
MOD2 to MOD0 Set to "0102"(1)
IVL
Select default ISCLKi output value(1)
RLD
Set to "0"
INV
Select whether ISCLKi puts in an
inversed signal or not(1)
15 to 0
Set bit rate
fBT1
= transfer clock
2 x (setting value + 2)
frequency
15 to 0
Set to a value smaller than the G1PO0
register(1)
FSC3,FSC1,FSC0 Set to "0"(1)
IFE3,IFE1,IFE0
Set to "1"(1)
7 to 0
Set to "0010 00002"
GMD1, GMD0
Set to "012"
CKDIR
Select the internal clock or external clock
STPS
Set to "0"
UFORM
Select either LSB first or MSB first
IRS
Select what cause the transmit interrupt to be generated
TI
Transmit buffer empty flag
TXEPT
Transmit register empty flag
RI
Receive complete flag
TE
Set to "1" to enable transmission and reception
RE
Set to "1" to enable reception
IPOL
Select ISRxDi input polarity (usually set to "0")
OPOL
Select ISTxDi output polarity (usually set to "0")
–
Write data to be transmitted
–
Received data and error flag are stored
i = 0 to 1
NOTES:
1. The CKDIR bit in the GiMR register is set to "0" (internal clock).
2. These registers must be set, when f8 or f2n is selected as transfer clock source notwithstanding.
Rev. 1.10 Oct. 18, 2005 Page 283 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
Table 21.16 Pin Settings in Clock Synchronous Serial I/O Mode (Communication Units 0 and 1)(1)
Port
Name
Setting
Function
PS1
Register
PSL1
Register
PSC
Register
PSD1
Register
PD7
Register
IPS
Register
P73
ISTxD1 Output
PS1_3=1
PSL1_3=0 PSC_3=1 -
-
P74
ISCLK1 Input
PS1_4=0
-
PD7_4=0 IPS1=0
G1POCR1
-
-
-
Register ( 1 )
ISCLK1 Output PS1_4=1
PSL1_4=0 PSC_4=1 -
-
P75
ISRxD1 Input
PS1_5=0
-
PD7_5=0 IPS1=0
p7 6
ISTxD0 Output
PS1_6=1
PSL1_6=0 PSC_6=0 PSD1_6=0 -
p7 7
ISCLK0 Input
PS1_7=0
-
ISCLK0 Output PS1_7=1
-
-
-
G1POCR0
-
-
-
PD7_7=0 IPS0=0
-
PSL1_7=0 -
-
-
-
-
NOTE:
1. Set the MOD2 to MOD0 bits in the corresponding register to "1112" (output from the communication
function used).
Table 21.17 Pin Settings (2)
Port
Name
P80
Function
ISRxD0 input
Setting
PS2 Register PD8 Register
PS2_0 = 0
PD8_0 = 0
IPS Register
IPS0 = 0
Table 21.18 Pin Settings (3)
Port
Name
P110
P111
P112
Setting
PS5 Register PD11 Register
ISTxD1 output PS5_0 = 1
ISCLK1 input
PS5_1 = 0
PD11_1 = 0
ISCLK1 output PS5_1 = 1
ISRxD1 input
PS5_2 = 0
PD11_2 = 0
Register(1)
Function
IPS Register
IPS1 = 1
IPS1 = 1
G1POCR0
G1POCR1
-
NOTE:
1. Set the MOD2 to MOD0 bits in the corresponding register to "1112" (output from communication
function used).
Table 21.19 Pin Settings (4)
Port
Name
P150
P151
P152
Function
PS9 Register
ISTxD0 output PS9_0 = 1
ISCLK0 input
PS9_1 = 0
ISCLK0 output PS9_1 = 1
ISRxD0 input
-
Rev. 1.10 Oct. 18, 2005 Page 284 of 435
REJ09B0162-0110
Setting
PD15 Register
PD15_2 = 0
PD15_2 = 0
IPS Register
IPS0 = 1
IPS0 = 1
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
(1) When f8, f2n or External Clock is Selected as the Communication Clock
(Communication Units 0 and 1)
Write to the GiTB register
f8, f2n or
External Clock
TE Bit
Transfer Clock
ISTxDi Pin Output
(transmit data)
Bit 0
Bit 1
Bit 2
Bit 6
Bit7
SIOiTR Bit when IRS=0
(no data in the
GiTB register)
SIOiTR Bit when IRS=1
(transmission completed)
Write "0" by program
if setting to "0"
Write "0" by program
if setting to "0"
ISRxDi Pin Input
(received data)
Bit 0
Bit 1
Bit 2
Bit 6
Bit7
SIOiRR Bit
Write "0" by program if setting to "0"
The above applies under the following conditions:
• The CKDIR bit in the GiMR register is set to "0" (internal clock)
• The CCS1 and CCS0 bits or the CCS3 and CCS2 bits in the CCS register
are set to "102" or "112"
• The UFORM bit in the GiMR register is set to "0" (LSB first)
• The IPOL and OPOL bits in the GiCR register are set to "0" (no inverse)
SIOiTR: Bit in the IIOjIR register (j=1, 3)
SIOiRR: Bit in the IIOkIR register (k=0, 2)
IRS: Bit in the GiMR register
TE: Bit in the GiCR register
i=0, 1
(2) When the Communication Clock is Generated in Channel 3 Phase-Delayed Waveform Output Mode
(Communication Unit 1)
Write to the G1TB register
The base timer is reset by the channel 0
waveform generation function
n+2
Base Timer
m
ISCLK1 Pin Output
(transmit clock in the
channel 3 generation
function)
ISTxD1 Pin Output
(transmit data)
Bit 0
Bit 1
Bit 2
Bit 6
Bit7
Bit 2
Bit 6
Bit 7
SIO1TR Bit when IRS=0
(no data in the
G1TB register)
Write "0" by program
if setting to "0"
ISRxD1 Pin Input
(received data)
Bit 0
Bit 1
SIO1RR Bit
Write "0" by program if setting to "0"
The above applies under the following conditions:
• The CKDIR bit in the G1MR register is set to "0" (internal clock)
• The CCS3 and CCS2 bits in the CCS register are set to "002"
• The UFORM bit in the G1MR register is set to "0" (LSB first)
• The IPOL and OPOL bits in the G1CR register are set to "0" (no inverse)
Figure 21.29 Transmit and Receive Operation
Rev. 1.10 Oct. 18, 2005 Page 285 of 435
REJ09B0162-0110
n: Setting value of the G1PO0 register
m: Setting value of the G1PO3 register
SIO1TR: Bit in the IIO3IR register
SIO1RR: Bit in the IIO2IR register
IRS: Bit in the G1MR register
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
21.4.2 Clock Asynchronous Serial I/O (UART) Mode (Communication Unit 1)
In clock asynchronous serial I/O (UART) mode, data is transmitted at a desired bit rate and in a desired
transfer data format. Table 21.20 lists specifications of UART mode in the communication unit 1. Table
21.21 lists clock settings. Table 21.22 lists register settings. Tables 21.23 and 21.24 list pin settings.
Figure 21.30 shows an example of transmit operation. Figure 21.31 shows an example of receive operation.
Table 21.20 UART Mode Specifications (Communication Unit 1)
Item
Transfer Data Format
Transfer
Clock(1)
Transmit Start Condition
Specification
• Character bit (transfer data) :
8 bits long
• Start bit :
1 bit long
• Parity bit:
selected from odd, even, or none
• Stop bit :
selected length from 1 bit or 2 bits
See Table 21.21
Set registers associated with the waveform generating function, the G1MR and G1ERC
registers. Then, set as is written below after at least one transfer clock cycle:
• Set the TE bit in the G1CR register to "1" (transmit enabled)
• Set the TI bit in the G1CR register to "0" (data written to the G1TB register)
Receive Start Condition
Set registers associated with the waveform generating function, the G1MR and G1ERC
registers. Then, set as is written below after at least one transfer clock cycle:
• Set the RE bit in the G1CR register to "1" (receive enabled)
• Detect the start bit
Interrupt Request
• While transmitting, one of the following conditions can be selected to set the
SIO1TR bit to "1" (interrupt requested) (See Figure 10.14.) :
_
The IRS bit in the G1MR register is set to "0" (no data in the G1TB register) and data
is transferred to the transmit register from the G1TB register.
_
The IRS bit is set to "1" (transmission completed) and data transfer from the
transmit register is completed
• While receiving, the following condition can be selected to set the SIO1RR bit is set
to "1":
Data is transferred from the receive register to the G1RB register (data reception
is completed)
Error Detection
• Overrun error(2)
This error occurs, when the next data reception is started and the final stop bit of the
next data is received before reading the G1RB register
• Parity error
While parity is enabled, this error occurs when the number of "1" in parity and character bits does not match the number of "1" set
• Framing error
This error occurs when the number of the stop bits set is not detected
Selectable Function
• Stop bit length
The length of the stop bit is selected from 1 bit or 2 bits
• LSB first or MSB first
Select either bit 0 or bit 7 to transmit or receive data
NOTES:
1. The transfer clock must be fBT1 divided by six or more.
2. When an overrun error occurs, the G1RB register is indeterminate.
Rev. 1.10 Oct. 18, 2005 Page 286 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
Table 21.21 Clock Settings (Communication Unit 1)
Transfer Clock(3)
G1MR Register
CKDIR Bit
fBT1 (1, 2)
2(n+2)
0
CCS Register
CCS2 Bit
CCS3 Bit
0
0
n: Setting value of the G1PO0 register 000116 to FFFD16
NOTES:
1. Transmit clock is generated in phase-delayed waveform output mode of the channel 3 waveform
generating function.
2. Received clock is generated when phase-delayed waveform mode of the channel 2 waveform generating function and the channel 2 time measurement function is simultaneously performed.
3. The transfer clock must be fBT1 divided by six or more.
Table 21.22 Register Settings in UART Mode (Communication Unit 1)
Register
G1BCR0
G1BCR1
G1POCR0
G1POCR2
G1POCR3
G1TMCR2
Bit
BCK1, BCK0
DIV4 to DIV0
IT
7 to 0
7 to 0
7 to 0
7 to 0
7 to 0
G1PO0
15 to 0
Set bit rate
fBT1
2 x (setting value + 2) = transfer clock frequency
G1PO3
G1FS
G1FE
G1MR
15 to 0
FSC3 to FSC0
IFE3 to IFE0
GMD1, GMD0
CKDIR
STPS
PRY, PRYE
UFORM
IRS
TI
TXEPT
RI
TE
RE
IPOL
OPOL
7 to 0
15 to 0
CCS3, CCS2
Set to a value smaller than the G1PO0 register
Set to "01002"
Set to "11012"
Set to "002"
Set to "0"
Select stop bit length
Select either parity enabled or disabled and either odd parity or even parity
Select either the LSB first or MSB first
Select what causes the receive interrupt to be generated
Transmit buffer empty flag
Transmit register empty flag
Receive complete flag
Set to "1" to enable transmission and reception
Set to "1" to enable reception
Set to "1"
Set to "1"
Write data to be transmitted
Received data and error flag are stored
Set to "002"
G1CR
G1TB
G1RB
CCS
Function
Set to "112" (f1)
Select divide ratio of count source
Set to "0"
Set to "0001 00102"
Set to "0000 01112"
Set to "0000 01102"
Set to "0000 00102"
Set to "0000 00102"
Table 21.23 Pin Settings in UART Mode
Port
Name
P73
P75
Function
ISTxD1 output
ISRxD1 input
Setting
Register(1)
PS1 Register PSL1 Register PSC Register PD7 Register IPS Register
PS1_3 = 1
PSL1_3 = 0
PSC_3 = 1
G1POCR0
PS1_5 = 0
PD7_5 = 0
IPS1 = 0
-
NOTE:
1. Set the MOD2 to MOD0 bits in the corresponding register to "1112" (output from communication
function used).
Rev. 1.10 Oct. 18, 2005 Page 287 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
Table 21.24 Pin Settings (Continued)
Port
Name
P110
P112
Function
ISTxD1 output
ISRxD1 input
Setting
Register(1)
PS5 Register PD11 Register IPS Register
PS5_0 = 1
G1POCR0
PS5_2 = 0
PD11_2 = 0
IPS1 = 1
-
NOTE:
1. Set the MOD2 to MOD0 bits in the corresponding register to "1112" (output from the communication
function used).
Tc
Internal
Transfer clock
ISTxD1 pin
"H"
ST D0 D1 D2 D3 D4 D5 D6 D7 SP
ST D0 D1 D2 D3 D4 D5 D6 D7
"L"
Set data in G1TB register
TI bit
SP
Set data in G1TB register
"1"
"0"
TXEPT bit
"1"
"0"
"1"
SIO1TR bit
"0"
Write "0" by program
if setting to "0"
The above applies under the following conditions:
• The STPS bit in the G1MR register is set to "0" (1 stop bit)
• The PRYE bit in the G1MR register is set to "0" (parity disabled)
• The UFORM bit in the G1MR register is set to "0" (LSB first)
• The INV bits in the G1POCR0 to G1POCR7 registers are set to "0" (no inverse)
• The IRS bit in the G1MR register is set to "0" (no data in the G1TB register)
TI, TXEPT: Bits in the G1CR register
SIO1TR: Bit in the IIO3IR register
Figure 21.30 Transmit Operation
Internal
transfer clock
ISRxD1 pin
"H"
ST D0 D1 D2 D3 D4 D5 D6 D7 SP
ST D0 D1 D2 D3 D4 D5 D6 D7 SP
"L"
Read the G1RB register
"1"
RI bit
"0"
"1"
SIO1RR bit
"0"
Write "0" by program
if setting to "0"
The above applies under the following conditions:
• The STPS bit in the G1MR register is set to "0" (1 stop bit)
• The PRYE bit in the G1MR register is set to "0" (parity disabled)
• The UFORM bit in the G1MR register is set to "0" (LSB first)
• The INV bits in the G1POCR0 to G1POCR7 registers are set to "0" (no inverse)
Figure 21.31 Receive Operation
Rev. 1.10 Oct. 18, 2005 Page 288 of 435
REJ09B0162-0110
SIO1RR: Bit in the IIO2IR register
RI: Bit in the G1CR register
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
21.4.3 HDLC Data Processing Mode (Communication Units 0 and 1)
In HDLC data processing mode, bit stuffing, flag detection, abort detection and CRC calculation are available
for HDLC control. f1, f8 or f2n can be selected as the communication unit 0 transfer clock. f1, f8, f2n or clock,
generated in the channel 0 or 1, can be selected as the communication unit 1 transfer clock. No pin is used.
To convert data, data to be transmitted is written to the GiTB register (i=0,1) and the data conversion result is
restored after data conversion. If any data are in the GiTO register after data conversion, the conversion is
terminated. If no data is in the GiTO register, bit stuffing processing is executed regardless of no data available in the transmit output buffer. A CRC value is calculated every time one bit is converted. If no data is in the
GiRI register, received data conversion is terminated.
Table 21.25 list specifications of the HDLC data processing mode. Tables 21.26 and 21.27 list clock settings.
Table 21.28 lists register settings.
Table 21.25 HDLC Processing Mode Specifications (Communication Units 0 and 1)
Item
Specification
Input Data Format
8-bit data fixed, bit alignment is optional
Output Data Format
8-bit data fixed
Transfer Clock
See Tables 21.26 and 21.27
I/O Method
• During transmit data processing,
value set in the GiTB register is converted in HDLC data processing mode and
transferred to the GiTO register.
• During received data processing,
value set in the GiRI register is converted in HDLC data processing mode and
transferred to the GiRB register. The value in the GiRI register is also transferred to
the GiTB register (received data register).
Bit Stuffing
During transmit data processing, "0" following five continuous "1" is inserted.
During received data processing, "0" following five continuous "1" is deleted.
Flag Detection
Write the flag data "7E16" to the GiCMPj register (j=0 to 3) to use the special commu-
Abort Detection
Write the masked data "0116" to the GiMSKj register
CRC
The CRC1 and CRC0 bits are set to "112" (X16+X12+X5+1).
The CRCV bit is set to "1" (set to "FFFF16").
nication interrupt (the SRTiR bit in the IIO4IR register)
• During transmit data processing,
CRC calculation result is stored into the GiTCRC register. The TCRCE bit in the
GiETC register is set to "1" (transmit CRC used).
The CRC calculation result is reset when the TE bit in the GiCR register is set to "0"
(transmit disabled).
• During received data processing,
CRC calculation result is stored into the GiRCRC register. The RCRCE bit in the
GiERC register is set to "1" (receive CRC used).
The CRC calculation result is reset by comparing the flag data "7E16" and matching
the result with the value in the GiCMP3 register. The ACRC bit in the GiEMR register is set to "1" (CRC reset).
Data Processing Start
Condition
The following conditions are required to start transmit data processing:
• The TE bit in the GiCR register is set to "1" (transmit enabled)
• Data is written to the GiTB register
The following conditions are required to start receive data processing:
• The RE bit in the GiCR register is set to "1" (receive enabled)
• Data is written to the GiRI register
Rev. 1.10 Oct. 18, 2005 Page 289 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
Table 21.25 HDLC Processing Mode Specifications (Continued)
Item
Specification
Interrupt Request
During transmit data processing,
• One of the following conditions can be selected to set the GiTOR bit(1) in the
_
interrupt request register to "1" (interrupt requested).
When the IRS bit in the GiMR register is set to "0" (no data in the GiTB
register) and data is transferred from the GiTB register to the transmit register (transmit start).
_
When the IRS bit is set to "1" (transmission completed) and data transfer from
the transmit register to the GiTO register is completed.
• When data, which is already converted to HDLC data, is transferred from the
receive register of the GiTO register to the transmit buffer, the GiTOR bit is set
to "1"
During received data processing,
• When data is transferred from the GiRI register to the GiRB register (reception
completed), the GiRIR bit(1) is set to "1".
• When received data is transferred from the receive buffer of the GiRI register to
the receive register, the GiRIR bit is set to "1".
• When the GiTB register is compared to the GiCMPj register (j=0 to 3), the
SRTiR bit(1) is set to "1".
NOTE:
1. See Figure 10.14 for details on the GiTOR bit, GiRIR bit and SRTiR bit.
Table 21.26 Clock Settings (Communication Unit 0)
Transfer Clock(1)
f1
f8
f2n(2)
CCS Register
CCS0 Bit
CCS1 Bit
1
0
1
1
0
1
NOTES:
1. The transfer clock for reception is generated when the RSHTE bit in the G0ERC register is set to "1"
(receive shift operation enabled).
2. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Table 21.27 Clock Settings (Communication Unit 1)
Transfer Clock(1)
fBT1
(2)
2x(n+2)
f1
f8
f2n(3)
CCS Register
CCS2 Bit
CCS3 Bit
0
0
1
1
0
0
1
1
n: Setting value of the G1PO0 register, 000116 to FFFD16
NOTES:
1. The transfer clock for reception is generated when the RSHTE bit in the G1ERC register is set to "1"
(receive shift operation enabled).
2. The transfer clock is generated in single-phase waveform output mode of the channel 1.
3. The CNT3 to CNT0 bits in the TCSPR register select no division (n=0) or divide-by-2n (n=1 to 15).
Rev. 1.10 Oct. 18, 2005 Page 290 of 435
REJ09B0162-0110
21. Intelligent I/O (Communication Function)
M32C/88 Group (M32C/88T)
Table 21.28 Register Settings in HDLC Processing Mode (Communication Units 0 and 1)
Register
G1BCR0
G1BCR1(1)
G1POCR0(1)
G1POCR1(1)
G1PO0(1)
G1PO1(1)
G1FS(1)
G1FE(1)
GiMR
GiEMR
GiCR
GiETC
GiERC
GiIRF
GiCMP0,
GiCMP1
GiCMP2
GiCMP3
GiMSK0,
GiMSK1
GiTCRC
GiRCRC
GiTO
GiRI
GiRB
GiTB
CCS
Bit
BCK1, BCK0
DIV4 to DIV0
IT
7 to 0
7 to 0
7 to 0
15 to 0
15 to 0
Function
Select count source
Select divide ratio of count source
Select the base timer interrupt
Set to "0001 00102"
Set to "0000 00002"
Set to "0000 00002"
Set bit rate
Set the timing of the rising edge of the transfer clock.
Timing of the falling edge ("H" width of the transfer clock) is fixed.
Setting value of the G1PO1 register ≤ Setting value of the G1PO0 register
FSC1, FSC0
Set to "002"
IFE1, IFE0
Set to "112"
GMD1, GMD0
Set to "112"
CKDIR
Set to "0"
UFORM
Set to "0"
IRS
Select what causes the transmit interrupt to be generated
7 to 0
Set to "1111 01102"
TI
Transmit buffer empty flag
TXEPT
Transmit register empty flag
RI
Receive complete flag
TE
Transmit enable bit
RE
Receive enable bit
SOF
Set to "0"
TCRCE
Select whether transmit CRC is used or not
ABTE
Set to "0"
TBSF1, TBSF0
Transmit bit stuffing
CMP2E to CMP0E Select whether received data is compared or not
CMP3E
Set to "1"
RCRCE
Select whether receive CRC is used or not
RSHTE
Set to "1" to use it in the receiver
RBSF1, RBSF0 Receive bit stuffing
BSERR, ABT
Set to "0"
IRF3 to IRF0
Select what causes an interrupt to be generated
7 to 0
Write "FE16" to abort processing
7 to 0
7 to 0
7 to 0
Data to be compared
Write "7E16"
Write "0116" to abort processing
15 to 0
15 to 0
7 to 0
7 to 0
7 to 0
7 to 0
Transmit CRC calculation result can be read
Receive CRC calculation result can be read
Data, which is output from a transmit data generation circuit, can be read
Set data input to a receive data generation circuit
Received data is stored
For transmission: write data to be transmitted
For reception : received data for comparison is stored
Select the HDLC processing clock
Select the HDLC processing clock
CCS1, CCS0
CCS3, CCS2
i=0, 1
NOTE:
1. These register settings are required when the CCS3 and CCS2 bit in the CCS register are set to "002"
(clock output from channel j (j=1 to 3)).
Rev. 1.10 Oct. 18, 2005 Page 291 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
22. CAN Module
The CAN (Controller Area Network) module included in the M32C/88 Group (M32C/88T) is a Full CAN
module, compatible with CAN Specification 2.0 Part B. Three channels, CAN0, CAN1, and CAN2, can be
used. Table 22.1 lists specifications of the CAN module.
Table 22.1 CAN Module Specifications
Item
Specification
Protocol
CAN Specification 2.0 Part B
Message Slots
16 slots
Polarity
Dominant: "L"
Recessive: "H"
Acceptance Filter
Global mask: 1 (for message slots 0 to 13)
Local mask: 2 (for message slots 14 and 15 respectively)
1
Baud Rate
Baud rate = Tq clock cycle x Tq per bit --- Max. 1 Mbps
BRP + 1
Tq clock cycle =
CAN clock
Tq per bit = SS + PTS +PBS1+PBS2
Tq: Time quantum
BRP: Setting value of the C0BRP and C1BRP registers, 1-255
SS: Synchronization Segment; 1 Tq
PTS: Propagation Time Segment; 1 to 8 Tq
PBS1: Phase Buffer Segment 1; 2 to 8 Tq
PBS2: Phase Buffer Segment 2 ; 2 to 8 Tq
Remote Frame Automatic
Message slot that receives the remote frame transmits the data frame
Answering Function
automatically
Time Stamp Function
Time stamp function with a 16-bit counter. Count source can be selected
from the CAN bus bit clock divided by 1, 2, 3 or 4
1
CAN bus bit clock = CAN bit time
BasicCAN Mode
BasicCAN function can be used with the CANi message slots 14 and 15
Transmit Abort Function
Transmit request is aborted
Loopback Function
Frame transmitted by the CAN module is received by the same CAN module
Forcible Error Active
The CAN module is forced into an error active state by resetting an error
Transition Function
counter.
Single-Shot Transmit Function The CAN module does not transmit data again even if arbitration lost or
transmission error causes a transmission failure
Self-Test Function
The CAN module communicates internally and diagnoses its CAN module
state
NOTE:
1. Use an oscillator with maximum 1.58% oscillator tolerance.
Rev. 1.10 Oct. 18, 2005 Page 292 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
Figure 22.1 shows a block diagram of the CAN module. Figure 22.2 shows CANi message slot (the message slot) j (j = 0 to 15) and CANi message slot buffer (i=0 to 2). Table 22.2 lists pin settings of the CAN
module.
The message slot cannot be accessed directly from the CPU. Allocate the message slot j to be used to the
message slot buffer 0 or 1. The message slot j is accessed via the message slot buffer address. The CiSBS
register selects the message slot j to be allocated. Figure 22.2 shows the 16-byte message slot buffer and
message slot.
Internal Data Bus
CAN0
f1
fCAN
"0"
CAN Clock
Baud Rate
Prescaler
"1"
PM25
See Figure 22.2
CAN0OUT
Self-test
Function
Acceptance
Filter
CAN0IN
CAN
Protocol
Controller
CAN Interrupt
Control Circuit
Message
Slots
0 to 15
Message
Slot
Buffer 0,1
Interrupt Request
CAN1
f1
fCAN
"0"
CAN Clock
"1"
PM25
Baud Rate
Prescaler
See Figure 22.2
CAN1OUT
Self-test
Function
Acceptance
Filter
CAN1IN
CAN
Protocol
Controller
CAN Interrupt
Control Circuit
Message
Slots
0 to 15
Message
Slot
Buffer 0,1
Interrupt Request
CAN2
f1
fCAN
"0"
CAN Clock
"1"
PM25
Baud Rate
Prescaler
See Figure 22.2
CAN2OUT
Self-test
Function
CAN2IN
Acceptance
Filter
CAN
Protocol
Controller
CAN Interrupt
Control Circuit
Figure 22.1 CAN Module Block Diagram
Rev. 1.10 Oct. 18, 2005 Page 293 of 435
REJ09B0162-0110
Message
Slots
0 to 15
Interrupt Request
Message
Slot
Buffer 0,1
22. CAN Module
M32C/88 Group (M32C/88T)
CANi Message Slot 0
CANi Message Slot 1
CANi Message Slot 2
CANi Message Slot 3
CANi Message Slot 4
CANi Message Slot 5
CANi Message Slot 6
CANi Message Slot 7
CANi Message Slot 8
CANi Message Slot 9
CANi Message Slot 10
CANi Message Slot 11
CANi Message Slot 12
CANi Message Slot 13
CANi Message Slot 14
CANi Message Slot 15
CiSBS
b3 to b0
CANi Message
Slot Buffer 0 (16 bytes)
CANi Message
Slot Buffer 1 (16 bytes)
CAN0
CAN1
CAN2
01E016
026016
018016
01EF16
01F016
026F16 018F16
027016 019016
01FF16
027F16 019F16
CiSBS
b7 to b4
Internal Data Bus
CANi Message Slot Buffer 0
CANi Message Slot j
CAN
Protcol
Controller
CANi Message Slot 0 Standard ID0
CANi Message Slot 0 Standard ID1
CANi message
slot buffer
CANi Message
Slot 0 Extended
ID00 standard ID0
CANi message
slot buffer
CANi Message
Slot 0 Extended
ID10 standard ID1
CANi message
slot buffer
CANi Message
Slot 0 Extended
ID20 extended ID0
CANi message
slotLength
buffer 0
extended ID1
CANi Message
Slot 0 Data
Code
CANi message
slot0buffer 0 extended ID2
CANi Message
Slot 0 Data
CANi message
slot1buffer 0 data length cod
CANi Message
Slot 0 Data
CANi message
slot2buffer 0 data 0
CANi Message
Slot 0 Data
CANi message
slot3buffer 0 data 1
CANi Message
Slot 0 Data
CANi message
slot4buffer 0 data 2
CANi Message
Slot 0 Data
CANi message
slot5buffer 0 data 3
CANi Message
Slot 0 Data
CANi message
slot6buffer 0 data 4
CANi Message
Slot 0 Data
CANi message
slot7buffer 0 data 5
CANi Message
Slot 0 Data
CANi message
slotStamp
buffer High-Ordered
0 data 6
CANi Message
Slot 0 Time
CANi message
slotStamp
buffer Low-Ordered
0 dataO7
CANi Message
Slot 0 Time
CANi Message Slot 15 Time Stamp Low-Ordered
i=0 to 2, j=0 to 15
CANi Message Slot Buffer 0 Standard ID0 (CiSLOT0_0)
CANi Message Slot Buffer 0 Standard ID1 (CiSLOT0_1)
CANi Message Slot Buffer 0 Extended ID0 (CiSLOT0_2)
CANi Message Slot Buffer 0 Extended ID1 (CiSLOT0_3)
CANi Message Slot Buffer 0 Extended ID2 (CiSLOT0_4)
CANi Message Slot Buffer 0 Data Length Code (CiSLOT0_5)
CANi Message Slot Buffer 0 Data 0 (CiSLOT0_6)
CANi Message Slot Buffer 0 Data 1 (CiSLOT0_7)
CANi Message Slot Buffer 0 Data 2 (CiSLOT0_8)
CANi Message Slot Buffer 0 Data 3 (CiSLOT0_9)
CANi Message Slot Buffer 0 Data 4 (CiSLOT0_10)
CANi Message Slot Buffer 0 Data 5 (CiSLOT0_11)
CANi Message Slot Buffer 0 Data 6 (CiSLOT0_12)
CANi Message Slot Buffer 0 Data 7 (CiSLOT0_13)
CANi Message Slot Buffer 0 Time Stamp High-Ordered (CiSLOT0_14)
CANi Message Slot Buffer 0 Time Stamp Low-Ordered (CiSLOT0_15)
CANi Message Slot Buffer 1
CANi Message Slot Buffer 1 Standard ID0 (CiSLOT1_0)
CANi Message Slot Buffer 1 Standard ID1 (CiSLOT1_1)
CANi Message Slot Buffer 1 Extended ID0 (CiSLOT1_2)
CANi Message Slot Buffer 1 Extended ID1 (CiSLOT1_3)
CANi Message Slot Buffer 1 Extended ID2 (CiSLOT1_4)
CANi Message Slot Buffer 1 Data Length Code (CiSLOT1_5)
CANi Message Slot Buffer 1 Data 0 (CiSLOT1_6)
CANi Message Slot Buffer 1 Data 1 (CiSLOT1_7)
CANi Message Slot Buffer 1 Data 2 (CiSLOT1_8)
CANi Message Slot Buffer 1 Data 3 (CiSLOT1_9)
CANi Message Slot Buffer 1 Data 4 (CiSLOT1_10)
CANi Message Slot Buffer 1 Data 5 (CiSLOT1_11)
CANi Message Slot Buffer 1 Data 6 (CiSLOT1_12)
CANi Message Slot Buffer 1 Data 7 (CiSLOT1_13)
CANi Message Slot Buffer 1 Time Stamp High-Ordered (CiSLOT1_14)
CANi Message Slot Buffer 1 Time Stamp Low-Ordered (CiSLOT1_15)
Figure 22.2 CANi Message Slot and CANi Message Slot Buffer
Rev. 1.10 Oct. 18, 2005 Page 294 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
Table 22.2 Pin Settings
Port
Function
Bit and Setting(2)
IPS, IPSA
Registers
PS0, PS1, PS2,
PS3 Registers
PSL0, PSL1, PSL2, PSC, PSC2, PSC3
PSL3 Registers
Registers
PSL0_0=1
P60
CAN2OUT
−
PS0_0=1
P61
CAN2IN
IPSA_7=0
PS0_1=0
P76
CAN0OUT
IPSA_7=0
PS1_6=1
CAN02OUT IPSA_7=1
CAN0IN
PD6, PD7, PD8,
PD9(1) Regsiters
−
−
−
PD6_1=0
PSL1_6=0
PSC_6=1
−
PS1_6=1
PSL1_6=0
PSC_6=1
−
IPS_3=0
PS1_7=0
−
−
PD7_7=0
CAN02IN
IPS_3=0,
IPSA_7=1
PS1_7=0
−
−
PD7_7=0
CAN0OUT
−
PS2_2=1
PSL2_2=1
PSC2_2=0
−
CAN1OUT
−
PS2_2=1
PSL2_2=1
PSC2_2=1
−
CAN0IN
IPS_3=1
−
−
−
PD8_3=0
CAN1IN
IPSA_3=1
−
−
−
PD8_3=0
P95
CAN1IN
IPSA_3=0
PS3_5=0
PSL3_5=0
−
PD9_5=0
P96
CAN1OUT
−
PS3_6=1
−
PSC3_6=1
−
P77
P82
P8 3
NOTE:
1. Set the PD9 and PS3 registers immediately after the PRC2 bit in the PRCR register is set to "1" (write
enabled). Do not generate an interrupt or a DMA transfer between the instruction to set to the PRC2
bit to "1" and the instruction to set the PD9 and PS3 registers.
Rev. 1.10 Oct. 18, 2005 Page 295 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1 CAN-Associated Registers
Figures 22.3 to 22.18, and Figures 22.20 to 22.33 show registers associated with CAN. To access the
CAN-associated registers, set the CM21 bit in the CM2 register to "0" (main clock or PLL clock as CPU
clock) and the MCD4 to MCD0 bits in the MCD register to "100102" (no division mode). Or, set the PM24 bit
in the PM2 register to "1" (main clock direct mode) and the PM25 bit in the PM2 regiseter to "1" (CAN clock).
Two wait states are added into the bus cycle.
Refer to 7. Processor Mode and 8. Clock Generation Circuit.
22.1.1 CANi Control Register 0 (CiCTLR0 Register) (i=0 to 2)
CANi Control Register 0 (i=0 to 2)
b15
b8 b7
b0
0
Symbol
Address
After Reset(1)
C0CTLR0
C1CTLR0
C2CTLR0
020116 - 020016
028116 - 028016
01A116 - 01A016
XXXX 0000 XX01 0X012
XXXX 0000 XX01 0X012
XXXX 0000 XX01 0X012
Bit
Symbol
Bit Name
RESET0 CAN Reset Bit 0
LOOPBACK
(b2)
BASICCAN
Loop Back Mode
Select Bit
(b7 - b6)
RW
0: CAN module reset exited
1: CAN module is reset(2)
RW
0: Disables loop back function
1: Enables loop back function
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
BasicCAN Mode
Select Bit
RESET1 CAN Reset Bit 1
(b5)
Function
Reserved Bit
0 : Disables BasicCAN mode function
1 : Enables BasicCAN mode function
RW
0: CAN module reset exited
1: CAN module is reset(2)
RW
Set to "0".
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
b9 b8
TSPRE0
0 0: Selects the CAN bus bit clock
0 1: Selects the CAN bus bit clock divided by 2
Time Stamp
Counter Reset Bit
0: Nothing is occurred
1: This bit is automatically set to "0" after RW
the CiTSR register is set to "000016"(3)
TSPRE1
TSRESET
RW
Time Stamp
Prescaler Select Bit
ECRESET Error Counter
Reset Bit
1 0: Selects the CAN bus bit clock divided by 3
RW
1 1: Selects the CAN bus bit clock divided by 4
0: Nothing is occurred
1: This bit is automatically set to "0" after RW
the CiTEC and CiREC registers are
set to "0016"(3)
Nothing is assigned. When write, set to "0".
(b15 - b12) When read, its content is indeterminate.
NOTES:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after reset
and supplying a clock to the CAN module.
2. Set the RESET1 and RESET0 bits to the same value simultaneously.
3. These bits can only be set to "1", not "0", by program.
Figure 22.3 C0CTLR0, C1CTLR0 and C2CTLR0 Registers
Rev. 1.10 Oct. 18, 2005 Page 296 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
22.1.1.1 RESET1 and RESET0 Bits
When both RESET1 and RESET0 bits are set to "1" (CAN module reset), the CAN module is immediately initialized regardless of ongoing CAN communication.
After the RESET1 and RESET0 bits are set to "1" and the CAN module reset is completed, the
CiTSR register (i=0 to 2) is set to "000016". The CiTEC and CiREC registers are set to "0016" and the
STATE_ERRPAS and STATE_BUSOFF bits in the CiSTR register are set to "0" as well.
When both RESET1 and RESET0 bit settings are changed "1" to "0", the CiTSR register starts
counting. CAN communication is available after 11 continuous recessive bits are detected.
NOTES:
1. Set the same value in both RESET1 and RESET0 bits simultaneously.
2. Confirm that the STATE_RESET bit in the CiSTR register is set to "1" (CAN module reset
completed) after setting the RESET1 and RESET0 bits to "1".
3. The CANOUT pin puts in a high-level ("H") signal as soon as the RESET1 and RESET0 bits are
set to "1". CAN bus error may occur when the RESET1 and RESET0 bits are set to "1" while the
CAN frame is transmitting.
4. For CAN communication, set the PS0, PS1, PS2, PS3, PSL0, PSL1, PSL2, PSL3, PSC, PSC2,
PSC3, IPS, IPSA, PD6, PD7, PD8, and PD9 registers when the STATE_RESET bit is set to "1"
(CAN module reset completed).
22.1.1.2 LOOPBACK Bit
When the LOOPBACK bit is set to "1" (loopback function enabled) and the receive message slot has
a matched ID and frame format with a transmitted frame, the transmitted frame is stored to the
receive message slot.
NOTES:
1. No ACK for the transmitted frame is returned.
2. Change the LOOPBACK bit setting only when the STATE_RESET bit is set to "1" (CAN module
reset completed).
22.1.1.3 BASICCAN Bit
When the BASICCAN bit is set to "1", the message slots 14 and 15 enter BasicCAN mode.
In BasicCAN mode, the message slots 14 and 15 are used as dual-structured buffers. The message
slots 14 and 15 alternately store a received frame having matched ID detected by acceptance filtering.
ID in the message slot 14 and the CiLMAR0 to CiLMAR4 registers are used for acceptance filtering
when the message slot 14 is active (the next received frame is to be stored in the message slot 14).
ID in the message slot 15 and the CiLMBR0 to CiLMBR4 registers are used when the message slot
15 is active. Both data frame and remote frame can be received.
Use the following procedure to enter BasicCAN mode.
(1) Set the BASICCAN bit to "1".
(2) Set the same value into IDs in the message slots 14 and 15.
(3) Set the same value in the CiLMAR0 to CiLMAR4 registers and CiLMBR0 to CiLMBR4 registers.
(4) Set the IDE14 and IDE15 bits in the CiIDR register to select a frame format (standard or extended) for the message slots 14 and 15. (Set to the same format.)
(5) Set the CiMCTL14 and CiMCTL15 registers in the message slots 14 and 15 to receive the data
frame.
Rev. 1.10 Oct. 18, 2005 Page 297 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
NOTES:
1. Change the BASICCAN bit setting only when the STATE_RESET bit is set to "1" (CAN module
reset completed).
2. The message slot 14 is the first slot to become active after the RESET1 and RESET0 bits are
set to "0".
3. The message slots 0 to 13 are not affected by entering BasicCAN mode.
22.1.1.4 TSPRE1, TSPRE0 Bits
The TSPRE1 and TSPRE0 bits determine which count source is used for the time stamp counter.
NOTE:
1. Change the TSPRE1 and TSPRE0 bit settings only when the STATE_RESET bit is set to "1"
(CAN module reset completed).
22.1.1.5 TSRESET Bit
When the TSRESET bit is set to "1", the CiTSR register is set to "000016". The TSRESET bit is
automatically set to "0" after the CiTSR register is set to "000016".
22.1.1.6 ECRESET Bit
When the ECRESET bit is set to "1", the CiTEC and CiREC registers are set to "0016". The CAN
module forcibly goes into an error active state.
The ECRESET bit is automatically set to "0" after the CAN module enters an error active state.
NOTES:
1. In an error active state, the CAN module is ready to communicate when 11 continuous recessive bits are detected on the CAN bus.
2. The CANiOUT pin provides an "H" signal output as soon as the ECRESET bit is set to "1". The
CAN bus error may occur when setting the ECRESET bit to "1" during CAN frame transmission.
Rev. 1.10 Oct. 18, 2005 Page 298 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.2 CANi Control Register 1 (CiCTLR1 Register) (i=0 to 2)
CANi Control Register 1 (i=0 to 2)
b7
b6
b5
b4
0 0
b3
b2
b1
Symbol
C0CTLR1
C1CTLR1
C2CTLR1
b0
0
Bit
Symbol
(b1 - b0)
After Reset(1)
X000 00XX2
X000 00XX2
X000 00XX2
Address
024116
025116
017116
Bit Name
Function
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
Set to "0".
RW
0: Selects the message slot control
register and single-shot register
1: Selects the mask register
RW
Reserved Bit
Set to "0".
RW
CANi Interrupt Mode
Select Bit
0: Outputs 3 types of interrupts via OR
1: Outputs 3 types of interrupts separately
RW
Reserved Bit
(b2)
BANKSEL CANi Bank Select Bit
(b5 - b4)
INTSEL
(b7)
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
NOTE:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset and supplying a clock to the CAN module.
Figure 22.4 C0CTLR1, C1CTLR1 and C2CTLR1 Registers
22.1.2.1 BANKSEL Bit
The BANKSEL bit in the C0CTLR1 register selects the registers allocated to addresses 022016 to
023F16. The BANKSEL bit in the C1CTLR1 register selects registers allocated to addresses 02A016
to 02BF16. The BANKSEL bit in the C2CTLR1 register selects registers allocated to addresses
01C016 to 01DF16.
The CiSSCTLR register, CiSSSTR register, and the CiMCTL0 to CiMCTL15 registers can be accessed by setting the BANKSEL bit to "0". The CiGMR0 to CiGMR4 registers, CiLMAR0 to CiLMAR4
registers and CiLMBR0 to CiLMBR4 registers can be accessed by setting the BANKSEL bit to "1".
22.1.2.2 INTSEL Bit
The INTSEL bit determines whether the three types of interrupt outputs (CANi transmit interrupt,
CANi receive interrupt and CANi error interrupt) are provided via OR or is separately.
Refer to 22.4 CAN Interrupts for details.
NOTE:
1. Change the INTSEL bit setting when the STATE_RESET bit is set to "1" (CAN module reset
completed).
Rev. 1.10 Oct. 18, 2005 Page 299 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.3 CANi Sleep Control Register (CiSLPR Register) (i=0 to 2)
CANi Sleep Control Register (i=0 to 2)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
C0SLPR
Address
024216
XXXX XXX02
C1SLPR
C1SLPR
025216
017216
XXXX XXX02
XXXX XXX02
Bit
Symbol
Bit Name
SLEEP
Sleep Mode Control Bit
After Reset
Function
RW
0: Enters sleep mode
1: Exits sleep mode(1)
RW
Nothing is assigned. When write, set to "0".
(b7 - b1) When read, its content is indeterminate.
NOTE:
1. Set up the initial setting for the CAN module after CAN sleep mode is exited. While the CAN0 module
is in sleep mode, no SFR (addresses 01E016 to 024516) for CAN0, except the C0SLPR register, can
be accessed. While the CAN1 module is in sleep mode, no SFR (addresses 025016 to 02BF16) for
CAN1, except the C1SLPR register, can be accessed. While the CAN2 module is in sleep mode, no
SFR (addresses 017016 to 017516, 018016 to 01DF16) for CAN2, except the C2SLPR register, can be
accessed.
Figure 22.5 C0SLPR, C1SLPR and C2SLPR Registers
22.1.3.1 SLEEP Bit
When the SLEEP bit is set to "0", the clock supplied to the CAN module stops running and the CAN
module enters sleep mode.
When the SLEEP bit is set to "1", the clock supplied to the CAN module starts running and the CAN
module exits sleep mode.
NOTE:
1. Enter sleep mode after the STATE_RESET bit in the CiSTR register is set to "1" (CAN module
reset completed).
Rev. 1.10 Oct. 18, 2005 Page 300 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.4 CANi Status Register (CiSTR Register) (i=0 to 2)
CANi Status Register (i=0 to 2)
b15
b8 b7
b0
Symbol
Address
After Reset(1)
C0STR
C1STR
020316 - 020216
028316 - 028216
X000 0X01 0000 00002
X000 0X01 0000 00002
C2STR
01A316 - 01A216
X000 0X01 0000 00002
Bit
Symbol
Bit Name
b3 b2 b1 b0
MBOX0
MBOX1
Function
Active Slot
Determination Bit
MBOX2
0 0 0 0: Message slot 0
0 0 0 1: Message slot 1
0 0 1 0: Message slot 2
0 0 1 1: Message slot 3
1 1 0 1: Message slot 13
1 1 1 0: Message slot 14
1 1 1 1: Message slot 15
MBOX3
RW
RO
RO
RO
RO
TRMSUCC
Transmit Complete
State Flag
0: Transmission is not completed
RO
1: Transmission is completed
RECSUCC
Receive Complete
State Flag
0: Reception is not completed
1: Reception is completed
RO
TRMSTATE
Transmit State Flag
0: Not transmitting
1: During transmission
RO
RECSTATE
Receive State Flag
0: Not receiving
1: During reception
RO
STATE_RESET CAN Reset State Flag
0: CAN module is operating
RO
1: CAN module reset is completed
STATE_LOOPBACK Loop Back State Flag
0: Mode except Loop back mode
RO
1: Loop back mode
(b10)
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
STATE_BASICCAN BasicCAN State Flag
0: Mode except BasicCAN mode
RO
1: BasicCAN mode
STATE_BUSERROR CAN Bus Error State Flag
0: No error occurs
1: Error occurs
RO
STATE_ERRPAS Error Passive State Flag
0: No error passive state
1: Error passive state
RO
STATE_BUSOFF Bus-Off State Flag
0: No bus-off state
1: Bus-off state
RO
(b15)
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
NOTE:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after reset
and supplying a clock to the CAN module after reset.
Figure 22.6 C0STR, C1STR and C2STR Registers
22.1.4.1 MBOX3 to MBOX0 Bits
The MBOX3 to MBOX0 bits store relevant slot numbers when the CAN module has completed transmitting data or storing received data.
22.1.4.2 TRMSUCC Bit
The TRMSUCC bit is set to "1" when the CAN module has transmitted data as expected.
The TRMSUCC bit is set to "0" when the CAN module has received data as expected.
Rev. 1.10 Oct. 18, 2005 Page 301 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
22.1.4.3 RECSUCC Bit
The RECSUCC bit is set to "1" when the CAN module has received data as expected. (Whether
received message has been stored in the message slot or not is irrelevant.) If the received message
is transmitted in loopback mode, the TRMSUCC bit is set to "1" and the RECSUCC bit is set to "0".
The RECSUCC bit is set to "0" when the CAN module has transmitted data as expected.
22.1.4.4 TRMSTATE Bit
The TRMSTATE bit is set to "1" when the CAN module is performing as a transmit node.
The TRMSTATE bit is set to "0" when the CAN module is in a bus-idle state or starts performing as a
receive node.
22.1.4.5 RECSTATE Bit
The RECSTATE bit is set to "1" when the CAN module is performing as a receive node.
The RECSTATE bit is set to "0" when the CAN module is in a bus-idle state or starts performing as a
transmit node.
22.1.4.6 STATE_RESET Bit
After both RESET1 and RESET0 bits are set to "1" (CAN module reset), the STATE_RESET bit is set
to "1" as soon as the CAN module is initialized.
The STATE_RESET bit is set to "0" when the RESET1 and RESET0 bits are set to "0".
22.1.4.7 STATE_LOOPBACK Bit
The STATE_ LOOPBACK bit is set to "1" when the CAN module is in loopback mode.
The STATE_LOOPBACK bit is set to "1" when the LOOPBACK bit in the CiCTLR0 register is set to "1"
(loop back function enabled).
The STATE_LOOPBACK bit is set to "0" when the LOOPBACK bit is set to "0" (loop back function
disabled).
22.1.4.8 STATE_BASICCAN Bit
The STATE_BASICCAN bit is set to "1" when the CAN module is in BasicCAN mode.
Refer to 22.1.1.3 BASICCAN bit for BasicCAN mode.
The STATE_BASICCAN bit is set to "0" when the BASICCAN bit is set to "0" (BasicCAN mode
function disabled).
The STATE_BASICCAN bit is set to "1" when the BASICCAN bit is set to "1" (BasicCAN mode
function enabled), the REMACTIVE bits in the CiMCTL14 and CiMCTL15 registers in the message
slots 14 and 15 are set to "0" (data frame received).
22.1.4.9 STATE_BUSERROR Bit
The STATE_BUSERROR bit is set to "1" when an CAN communication error is detected.
The STATE_BUSERROR bit is set to "0" when the CAN module has transmitted or received data as
expected. Whether a received message has been stored into the message slot or not is irrelevant.
NOTE:
1. When the STATE_BUSERROR bit is set to "1", the STATE_BUSERROR bit remains unchanged even if both RESET1 and RESET0 bits are set to "1" (CAN module reset).
Rev. 1.10 Oct. 18, 2005 Page 302 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
22.1.4.10 STATE_ERRPAS Bit
The STATE_ERRPAS bit is set to "1" when the value of the CiTEC or CiREC register (i=0, 1) exceeds 127 and the CAN module is placed in an error-passive state.
The STATE_ERRPAS bit is set to "0" when the CAN module in an error-passive state is placed in
another error state.
The STATE_ERRPAS bit is set to "0" when both RESET1 and RESET0 bits are set to "1" (CAN
module is reset).
22.1.4.11 STATE_BUSOFF Bit
The STATE_BUSOFF bit is set to "1" when the value of the CiTEC register exceeds 255 and the
CAN module is placed in a bus-off state.
The STATE_BUSOFF bit is set to "0" when the CAN module in a bus-off state is placed in an erroractive state.
The STATE_BUSOFF bit is set to "0" when both RESET1 and RESET0 bits are set to "1" (CAN
module reset).
Rev. 1.10 Oct. 18, 2005 Page 303 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.5 CANi Extended ID Register (CiIDR Register) (i=0 to 2)
CANi Extended ID Register (i=0 to 2)(1)
b15
b8 b7
b0
Symbol
C0IDR
C1IDR
Address
020516 - 020416
028516 - 028416
After Reset(2)
000016
000016
C2IDR
01A516 - 01A416
000016
Bit
Symbol
Bit Name
IDE15
Extended ID15 (Message Slot 15)
IDE14
Extended ID14 (Message Slot 14)
IDE13
Extended ID13 (Message Slot 13)
IDE12
Extended ID12 (Message Slot 12)
Function
Set corresponding
message slot to standard
or extended format
0: Standard format
1: Extended format
RW
RW
RW
RW
RW
IDE11
Extended ID11 (Message Slot 11)
RW
IDE10
Extended ID10 (Message Slot 10)
RW
IDE9
Extended ID9 (Message Slot 9)
RW
IDE8
Extended ID8 (Message Slot 8)
RW
IDE7
Extended ID7 (Message Slot 7)
RW
IDE6
Extended ID6 (Message Slot 6)
RW
IDE5
Extended ID5 (Message Slot 5)
RW
IDE4
Extended ID4 (Message Slot 4)
RW
IDE3
Extended ID3 (Message Slot 3)
RW
IDE2
Extended ID2 (Message Slot 2)
RW
IDE1
Extended ID1 (Message Slot 1)
RW
IDE0
Extended ID0 (Message Slot 0)
RW
NOTES:
1. Change the CilDR register setting while the CiMCTLj (j=0 to 15) register, corresponding to the bit
to be changed, is set to "0016".
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset and supplying a clock to the CAN module.
Figure 22.7 C0IDR, C1IDR and C2IDR Registers
Bits in the CiIDR register determine the frame format in the message slot corresponding to each bit.
The standard format is selected when the bit is set to "0".
The extended format is selected when the bit is to set "1".
Rev. 1.10 Oct. 18, 2005 Page 304 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.6 CANi Configuration Register (CiCONR Register) (i=0 to 2)
CANi Configuration Register (i=0 to 2)
b15
b8 b7
b0
Symbol
Address
After Reset(1)
C0CONR
C1CONR
020716 - 020616
028716 - 028616
0000 0000 0000 XXXX2
0000 0000 0000 XXXX2
C2CONR
01A716 - 01A616
0000 0000 0000 XXXX2
Bit
Symbol
(b3 - b0)
SAM
Bit Name
Function
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
Sampling Number
0: Sampled once
1: Sampled three times
RW
b7 b6 b5
PTS0
PTS1
Propagation Time
Segment
PTS2
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0 : 1Tq
1 : 2Tq
0 : 3Tq
1 : 4Tq
0 : 5Tq
1 : 6Tq
0 : 7Tq
1 : 8Tq
RW
RW
RW
b10 b9 b8
PBS10
PBS11
Phase Buffer
Segment 1
PBS12
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0 : Do not set to this value
1 : 2Tq
0 : 3Tq
1 : 4Tq
0 : 5Tq
1 : 6Tq
0 : 7Tq
1 : 8Tq
RW
RW
RW
b13b12 b11
PBS20
PBS21
Phase Buffer
Segment 2
PBS22
SJW0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0 : Do not set to this value
1 : 2Tq
0 : 3Tq
1 : 4Tq
0 : 5Tq
1 : 6Tq
0 : 7Tq
1 : 8Tq
b15 b14
reSynchronization
Jump Width
SJW1
0
0
1
1
0 : 1Tq
1 : 2Tq
0 : 3Tq
1 : 4Tq
RW
RW
RW
RW
RW
NOTE:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after reset
and supplying a clock to the CAN module after reset.
Figure 22.8 C0CONR, C1CONR and C2CONR Registers
Rev. 1.10 Oct. 18, 2005 Page 305 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.6.1 SAM Bit
The SAM bit determines the number of sample points to be taken per bit.
When the SAM bit is set to "0", only one sample is taken per bit at the end of the Phase Buffer
Segment 1 (PBS1) to determine the value of the bit.
When the SAM bit is set to "1", three samples per bit are taken; one time quantum and two time
quanta before the end of PBS1, and at the end of PBS1. The sample result value which is detected
more than twice becomes the value of the bit sampled.
22.1.6.2 PTS2 to PTS0 Bits
The PTS2 to PTS0 bits determine PTS width.
22.1.6.3 PBS12 to PBS10 Bits
The PBS12 to PBS10 bits determine PBS1 width. Set the PBS12 to 10 bits to "0012" or more.
22.1.6.4 PBS22 to PBS20 Bits
The PBS22 to PBS20 bits determine PBS2 width. Set the PBS22 to PBS20 bits to "0012" or more.
22.1.6.5 SJW1 and SJW0 Bits
The SJW1 and SJW0 bits determine SJW width. Set the SJW1 and SJW0 bits to values less than or
equal to the PBS12 to PBS10 bit settings and the PBS22 to PBS20 bit settings.
Table 22.3 Bit Timing when CAN Clock = 30 MHz
Baud Rate
BRP
Tq Clock Cycles (ns)
Tq Per Bit
1Mbps
1
66.7
15
1
66.7
15
1
66.7
15
2
100
10
2
100
10
2
100
10
500Kbps
2
100
20
2
100
20
2
100
20
3
133.3
15
3
133.3
15
3
133.3
15
4
166.7
12
4
166.7
12
4
166.7
12
5
200
10
5
200
10
5
200
10
Rev. 1.10 Oct. 18, 2005 Page 306 of 435
REJ09B0162-0110
PTS+PBS1
12
11
10
7
6
5
16
15
14
12
11
10
9
8
7
7
6
5
PBS2
2
3
4
2
3
4
3
4
5
2
3
4
2
3
4
2
3
4
Sample Point
87%
80%
73%
80%
70%
60%
85%
80%
75%
87%
80%
73%
83%
75%
67%
80%
70%
60%
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.7 CANi Baud Rate Prescaler (CiBRP Register) (i=0 to 2)
CANi Baud Rate Prescaler (i=0 to 2)(1)
b7
b0
Symbol
C0BRP
C1BRP
Address
021716
029716
After Reset(2)
0116
0116
C2BRP
01B716
0116
Function
If setting value is n, the CAN clock is divided
by (n+1).
Setting Range
RW
0116 to FF16(3)
RW
NOTES:
1. Set the CiBRP register while the STATE_RESET bit in the CiSTR register is set to "1" (CAN module
reset completed).
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after reset
and supplying a clock to the CAN module after reset.
2. Do not set to "0016" (divide-by-1).
Figure 22.9 C0BRP, C1BRP and C2BRP Registers
The CiBRP register determines the Tq clock cycle of the CAN bit time. The baud rate is obtained from
Tq clock cycle x Tq per bit.
Tq clock cycle = (BRP+1) / CAN clock
Baud rate =
1
Tq clcok cycle x Tq per bit
Tq per bit = SS + PTS + PBS1 + PBS2
Tq: Time quantum
SS: Synchronization Segment; 1 Tq
PBS1: Phase Buffer Segment 1; 2 to 8 Tq
Rev. 1.10 Oct. 18, 2005 Page 307 of 435
REJ09B0162-0110
BRP: Setting value of the CiBPR register; 1-255
PTS: Propagation Time Segment; 1 to 8 Tq
PBS2: Phase Buffer Segment 2; 2 to 8 Tq
22. CAN Module
M32C/88 Group (M32C/88T)
CANi Time Stamp Register (i=0 to 2)
b15
b8
b7
b0
Symbol
C0TSR
Address
020916 - 020816
After Reset(1)
000016
C1TSR
C2TSR
028916 - 028816
01A916 - 01A816
000016
000016
Function
Value of time stamp
RW
RO
NOTE:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset and supplying a clock to the CAN module.
22.1.8 CANi Time Stamp Register (CiTSR Register) (i=0 to 2)
Figure 22.10 C0TSR, C1TSR and C2TSR Registers
The CiTSR register is a 16-bit counter. The TSPRE1 and TSPRE0 bits in the CiCTLR0 register select
the CAN bus bit clock divided by 1, 2, 3 or 4 as the count source for the CiTSR register.
When data transmission or reception is completed, the value of the CiTSR register is automatically
stored into the message slot.
In loopback mode, when either data frame receive message slot or remote frame receive message
slot is available to store the message, the value of the CiTSR register is also stored into the message
slot when data reception is completed. The value of the CiTSR register is not stored when data
transmission is completed.
The CiTSR register starts a counter increment when the RESET1 and RESET0 bits in the CiCTLR0
register are set to "0".
The CiTSR register is set to "000016":
• at the next count timing after the CiTSR register is set to "FFFF16";
• when the RESET1 and RESET0 bits are set to "1" (CAN module reset) by program; or
1
• when the TSRESET bit is set to "1" (CiTSR register reset) by program.
CAN bit time
CAN bus bit clock =
Rev. 1.10 Oct. 18, 2005 Page 308 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
CANi Transmit Error Count Register (i=0 to 2)
b7
b0
Symbol
C0TEC
C1TEC
C2TEC
After Reset(1)
0016
0016
0016
Address
020A16
028A16
01AA16
Function
RW
Counter value of transmission errors
RO
NOTE:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after reset
and supplying a clock to the CAN module.
22.1.9 CANi Transmit Error Count Register (CiTEC Register) (i=0 to 2)
Figure 22.11 C0TEC, C1TEC and C2TEC Registers
In an error active or an error passive state, the counting value of a transmission error is stored into
the CiTEC register. The counter is decremented when the CAN module has transmitted data as
expected or is incremented when an transmit error occurs.
In a bus-off state, an indeterminate value is stored into the CiTEC register. The CiTEC register is set
to "0016" when the CAN module is placed in an error active state again.
CANi Receive Error Count Register (i=0 to 2)
b7
Symbol
C0REC
C1REC
C2REC
b0
After Reset(1)
0016
0016
0016
Address
020B16
028B16
01AB16
Function
Counter value of reception error
RW
RO
NOTE:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after reset
and supplying a clock to the CAN module after reset.
22.1.10 CANi Receive Error Count Register (CiREC Register) (i=0 to 2)
Figure 22.12 C0REC, C1REC and C2REC Registers
In an error active or an error passive state, a counting value of the reception error is stored into the
CiREC register. The counter is decremented when the CAN module has received data as expected
or it is incremented when a receive error occurs.
The CiREC register is set to 127 when the CiREC register is 128 (error passive state) or more and
the CAN module has received as expected.
In a bus-off state, an indeterminate value is stored into the CiREC register. The CiREC register is set
to "0016" when the CAN module is placed in an error active state again.
Rev. 1.10 Oct. 18, 2005 Page 309 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.11 CANi Slot Interrupt Status Register (CiSISTR Register) (i=0 to 2)
CANi Slot Interrupt Status Register (i=0 to 2)
b15
b8 b7
b0
Symbol
C0SISTR
Address
020D16 - 020C16
After Reset(1)
000016
C1SISTR
C2SISTR
028D16 - 028C16
01AD16 - 01AC16
000016
000016
Bit
Symbol
SIS15
SIS14
Bit Name
Message Slot 15 Interrupt
Request Status Bit
Message Slot 14 Interrupt
Request Status Bit
RW
Function
Determines whether an interrupt of
a corresponding message slot is
requested or not.
0: Interrupt not requested
1: Interrupt requested
RW
RW
(Note 2)
SIS13
Message Slot 13 Interrupt
Request Status Bit
SIS12
Message Slot 12 Interrupt
Request Status Bit
RW
SIS11
Message Slot 11 Interrupt
Request Status Bit
RW
SIS10
Message Slot 10 Interrupt
Request Status Bit
RW
SIS9
Message Slot 9 Interrupt
Request Status Bit
RW
SIS8
Message Slot 8 Interrupt
Request Status Bit
RW
SIS7
Message Slot 7 Interrupt
Request Status Bit
RW
SIS6
Message Slot 6 Interrupt
Request Status Bit
RW
SIS5
Message Slot 5 Interrupt
Request Status Bit
RW
SIS4
Message Slot 4 Interrupt
Request Status Bit
RW
RW
SIS3
Message Slot 3 Interrupt
Request Status Bit
RW
SIS2
Message Slot 2 Interrupt
Request Status Bit
RW
SIS1
Message Slot 1 Interrupt
Request Status Bit
RW
SIS0
Message Slot 0 Interrupt
Request Status Bit
RW
NOTES:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset and supplying a clock to the CAN module.
2. Set to "0" by program. If it is set to "1", the value before setting to "1" remains.
Figure 22.13 C0SISTR, C1SISTR and C2SISTR Registers
Rev. 1.10 Oct. 18, 2005 Page 310 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
When using the CAN interrupt, the CiSISTR register (i=0 to 2) indicates which message slot is requesting an interrupt. The SISj bits (j=0 to 15) are not automatically set to "0" (no interrupt requested) when an
interrupt is acknowledged. Set the SISj bits to "0" by program.
Use the MOV instruction, instead of the bit clear instruction, to set the SISj bits to "0". The SISj bits,
which are not being changed to "0", must be set to "1".
For example: To set the SIS0 bit to "0"
Assembly language:
mov.w
#07FFFh, C0SISTR
C language: c0sistr = 0x7FFF;
Refer to 22.4 CAN Interrupt for details.
22.1.11.1 Message Slot for Transmission
The SISj bit is set to "1" (interrupt requested) when the CiTSR register is stored into the message slot j
after data transmission is completed.
22.1.11.2 Message Slot for Reception
The SISj bit is set to "1" (interrupt requested) when the received message is stored in the message slot j
after data reception is completed.
NOTES:
1.If the automatic answering function is enabled in the remote frame receive message slot, the
SISj bit is set to "1" after the remote frame is received and the data frame is transmitted.
2.In the remote frame transmit message slot, the SISj bit is set to "1" after the remote frame is
transmitted and the data frame is received.
3.The SISj bit is set to "1" if the SISj bit is set to "1" by an interrupt request and "0" by program
simultaneously.
Rev. 1.10 Oct. 18, 2005 Page 311 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.12 CANi Slot Interrupt Mask Register (CiSIMKR Register) (i=0 to 2)
CANi Slot Interrupt Mask Register(1) (i=0 to 2)
b15
b8 b7
b0
Symbol
Address
After Reset(2)
C0SIMKR
021116 - 021016
000016
C1SIMKR
C2SIMKR
029116 - 029016
01B116 - 01B016
000016
000016
Bit
Symbol
SIM15
SIM14
SIM13
Bit Name
Function
RW
Message Slot 15 Interrupt Controls whether the interrupt
RW
Request Mask Bit
request of the corresponding
Message Slot 14 Interrupt message slot is enabled or masked.
RW
0: Masks (disables) an interrupt request
Request Mask Bit
Message Slot 13 Interrupt 1: Enables an interrupt request
RW
Request Mask Bit
SIM12
Message Slot 12 Interrupt
Request Mask Bit
RW
SIM11
Message Slot 11 Interrupt
Request Mask Bit
RW
SIM10
Message Slot 10 Interrupt
Request Mask Bit
RW
SIM9
Message Slot 9 Interrupt
Request Mask Bit
RW
SIM8
Message Slot 8 Interrupt
Request Mask Bit
RW
SIM7
Message Slot 7 Interrupt
Request Mask Bit
RW
SIM6
Message Slot 6 Interrupt
Request Mask Bit
RW
SIM5
Message Slot 5 Interrupt
Request Mask Bit
RW
SIM4
Message Slot 4 Interrupt
Request Mask Bit
RW
SIM3
Message Slot 3 Interrupt
Request Mask Bit
RW
SIM2
Message Slot 2 Interrupt
Request Mask Bit
RW
SIM1
Message Slot 1 Interrupt
Request Mask Bit
RW
SIM0
Message Slot 0 Interrupt
Request Mask Bit
RW
NOTES:
1. Change the CiSIMKR register setting while the CiMCTLj (j=0 to 15) register, corresponding to the bit to
be changed, is set to "0016".
2.Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after reset
and supplying a clock to the CAN module.
Figure 22.14 C0SIMKR, C1SIMKR and C2SIMKR Registers
The CiSIMKR register determines whether an interrupt request, generated by a data transmission or
reception in the corresponding message slot is enabled or disabled. When the SIMj bit (j=0 to 15) is set
to "1" (no interrupt requested), an interrupt request generated by a data transmission or reception in the
corresponding message slot is enabled. Refer to 22.4 CAN Interrupt for details.
Rev. 1.10 Oct. 18, 2005 Page 312 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.13 CANi Error Interrupt Mask Register (CiEIMKR Register) (i=0 to 2)
CANi Error Interrupt Mask Register (i=0 to 2)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset(1)
C0EIMKR
C1EIMKR
C2EIMKR
021416
029416
01B416
XXXX X0002
XXXX X0002
XXXX X0002
Bit
Symbol
Bit Name
Function
RW
BOIM
Bus-Off Interrupt
Mask Bit
0: Masks (disables) an interrupt request
1: Enables an interrupt request
RW
EPIM
Error-Passive Interrupt 0: Masks (disables) an interrupt request
1: Enables an interrupt request
Mask Bit
RW
BEIM
CAN Bus-Error Interrupt 0: Masks (disables) an interrupt request
Mask Bit
1: Enables an interrupt request
RW
Nothing is assigned. When write, set to "0".
(b7 - b3) When read, its content is indeterminate.
NOTE:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset and supplying a clock to the CAN module.
Figure 22.15 C0EIMKR, C1EIMKR and C2EIMKR Registers
Refer to 22.4 CAN Interrupt for details.
22.1.13.1 BOIM Bit
The BOIM bit determines whether an interrupt request is enabled or disabled when the CAN module is
placed in a bus-off state. When the BOIM bit is set to "1", the bus-off interrupt request is enabled.
22.1.13.2 EPIM Bit
The EPIM bit determines whether an interrupt request is enabled or disabled when the CAN module is
placed in an error passive state. When the EPIM bit is set to "1", the error passive interrupt request is
enabled.
22.1.13.3 BEIM Bit
The BEIM bit determines whether an interrupt request is enabled or disabled when a CAN bus error
occurs. When the BEIM bit is set to "1", the CAN bus error interrupt request is enabled.
Rev. 1.10 Oct. 18, 2005 Page 313 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.14 CANi Error Interrupt Status Register (CiEISTR Register) (i=0 to 2)
CANi Error Interrupt Status Register (i=0 to 2)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
C0EISTR
C1EISTR
Address
021516
029516
C2EISTR
01B516
Bit
Symbol
After Reset(1)
XXXX X0002
XXXX X0002
XXXX X0002
Bit Name
Function
RW
BOIS
Bus-Off Interrupt
Status Bit(2)
0: Interrupt not requested
1: Interrupt requested
RW
EPIS
Error-Passive Interrupt
Status Bit(2)
0: Interrupt not requested
1: Interrupt requested
RW
BEIS
CAN Bus-Error Interrupt 0: Interrupt not requested
1: Interrupt requested
Status Bit(2)
RW
Nothing is assigned. When write, set to "0".
(b7 - b3) When read, its content is indeterminate.
NOTES:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset and supplying a clock to the CAN module.
2. Set to "0" by program. When it is set to "1", the value before setting to "1" remains.
Figure 22.16 C0EISTR, C1EISTR and C2EISTR Registers
When using the CAN interrupt, the CiEISTR register indicates the source of the generated error interrupt. The BOIS, EPIS and BEIS bits are not automatically set to "0" (no interrupt requested) even if an
interrupt is acknowledged. Set these bits to "0" by program.
Use the MOV instruction, instead of the bit clear instruction, to set each bit in the CiEISTR register to "0".
Bits not being changed to "0" must be set to "1".
For example: To set the BOIS bit for CAN0 to "0"
Assembly language:
mov.b#006h, C0EISTR
C language:
c0eistr = 0x06;
Refer to 22.4 CAN Interrupt for details.
22.1.14.1 BOIS Bit
The BOIS bit is set to "1" when the CAN module is placed in a bus-off state.
22.1.14.2 EPIS Bit
The EPIS bit is set to "1" when the CAN module is placed in an error passive state.
22.1.14.3 BEIS Bit
The BEIS bit is set to "1" when a CAN bus error is detected.
Rev. 1.10 Oct. 18, 2005 Page 314 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.15 CANi Error Factor Register (CiEFR Register) (i=0 to 2)
CANi Error Factor Register (i=0 to 2)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset(1)
C0EFR
021616
0016
C1EFR
C2EFR
029616
01B616
0016
0016
Bit
Symbol
Bit Name
Function
RW
ACKE
ACK Error Detect Bit(2)
0: Detects no ACK error
1: Detects an ACK error
RW
CRCE
CRC Error Detect Bit(2)
0: Detects no CRC error
1: Detects a CRC error
RW
0: Detects no form error
1: Detects a form error
RW
RW
FORME FORM Error Detect Bit(2)
STFE
Stuff Error Detect Bit(2)
0: Detects no stuff error
1: Detects a stuff error
BITE0
Bit Error Detect Bit 0(2)
0: Detects no bit error while transmitting "H"
RW
1: Detects a bit error while transmitting "H"
BITE1
Bit Error Detect Bit 1(2)
0: Detects no bit error while transmitting "L"
RW
1: Detects a bit error while transmitting "L"
RCVE
Receive Error Detect Bit(2)
0: Detects no error while receiving data
RW
1: Detects an error while receiving data
TRE
Transmit Error Detect Bit(2)
0: Detects no error while transmitting data
RW
1: Detects an error while transmitting data
NOTES:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset and supplying a clock to the CAN module.
2. Set to "0" by program. If it is set to "1", the value before setting to "1" remains.
Figure 22.17 C0EFR, C1EFR and C2EFR Registers
The CiEFR register indicates the cause of error when a communication error is detected. Set the following bits to "0" by program because they are not changed "1" to "0" automatically.
Use the MOV instruction, instead of the bit clear instruction, to set each bit in the CiEFR register to "0".
Bits not being changed to "0" must be set to "1".
For example: To set the ACKE bit for CAN0 to "0"
Assembly language:
mov.b#0FEh, C0EFR
C language:
c0efr = 0xFE;
22.1.15.1 ACKE Bit
The ACKE bit is set to "1" when an ACK error is detected.
22.1.15.2 CRCE Bit
The CRC bit is set to "1" when a CRC error is detected.
22.1.15.3 FORME Bit
The FORME bit is set to "1" when a form error is detected.
22.1.15.4 STFE Bit
The STFE bit is set to "1" when a stuff error is detected.
22.1.15.5 BITE0 Bit
The BITE0 bit is set to "1" when a bit error is detected while transmitting recessive "H".
22.1.15.6 BITE1 Bit
The BITE1 bit is set to "1" when a bit error is detected while transmitting dominant "L".
22.1.15.7 RCVE Bit
The RCVE bit is set to "1" when an error is detected while receiving data.
22.1.15.8 TRE Bit
The TRE bit is set to "1" when an error is detected while transmitting data.
Rev. 1.10 Oct. 18, 2005 Page 315 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.16 CANi Mode Register (CiMDR Register) (i=0 to 2)
CANi Mode Register (i=0 to 2)(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset(2)
C0MDR
021916
XXXX XX002
C1MDR
029916
XXXX XX002
C2MDR
01B916
XXXX XX002
Bit
Symbol
Bit Name
Function
RW
b1 b0
CMOD
(b7 - b2)
CAN Operating Mode
Select Bit
0 0: Normal operating mode
0 1: Bus monitoring mode
1 0: Self-test mode
1 1: Do not set to this value
RW
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
NOTES:
1. Set the CiMDR register when the STATE_RESET bit in the CiSTR register is set to "1" (CAN module
reset completed).
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset and supplying a clock to the CAN module.
Figure 22.18 C0MDR, C1MDR and C2MDR Registers
22.1.16.1 CMOD Bit
The CMOD bit selects a CAN operating mode.
• Normal operating mode: The CAN module transmits and receives data as expected.
• Bus monitoring mode(1): The CAN module receives data. Output signal from the CANiOUT pin is
fixed as a high-level ("H") signal in bus monitoring mode. The CAN mod
ule transmits neither ACK nor error frame.
• Self-test mode: The CAN module connects the CANiOUT pin to the CANiIN pin internally.
The CAN module can communicate without additional device in loop back mode.
Output signal from the CANiOUT pin is fixed as an "H" signal in self-test mode while
transmitting data. Figure 22.19 shows an image diagram in self-test mode.
NOTE:
1. Do not generate a transmit request in bus monitoring mode.
The CAN module assumes the ACK bit is set to dominant "L" regardless of the ACK bit setting.
Therefore, when the CRC delimiter is received as expected, the CAN module determines the
data is received with no error regardless of the ACK bit setting.
Rev. 1.10 Oct. 18, 2005 Page 316 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
CAN Module
Self-test Mode
CANiIN Pin
CANiIN
ACK Signal
Generation Circuit
CANiOUT
CANiOUT Pin
i=0 to 2
Figure 22.19 Self-Test Mode
Rev. 1.10 Oct. 18, 2005 Page 317 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.17 CANi Single-Shot Control Register (CiSSCTLR Register) (i=0 to 2)
CANi Single-Shot Control Register (i=0 to 2)(1, 2)
b15
b8 b7
b0
Symbol
C0SSCTLR
Address
022116 - 022016
After Reset(3)
000016
C1SSCTLR
C2SSCTLR
02A116 - 02A016
01C116 - 01C016
000016
000016
Bit
Symbol
Bit Name
SSC15
Message Slot 15 Single-Shot
Control Bit
SSC14
Message Slot 14 Single-Shot
Control Bit
RW
SSC13
Message Slot 13 Single-Shot
Control Bit
RW
SSC12
Message Slot 12 Single-Shot
Control Bit
RW
SSC11
Message Slot 11 Single-Shot
Control Bit
RW
SSC10
Message Slot 10 Single-Shot
Control Bit
RW
SSC9
Message Slot 9 Single-Shot
Control Bit
RW
SSC8
Message Slot 8 Single-Shot
Control Bit
RW
SSC7
Message Slot 7 Single-Shot
Control Bit
RW
SSC6
Message Slot 6 Single-Shot
Control Bit
RW
SSC5
Message Slot 5 Single-Shot
Control Bit
RW
SSC4
Message Slot 4 Single-Shot
Control Bit
RW
SSC3
Message Slot 3 Single-Shot
Control Bit
RW
SSC2
Message Slot 2 Single-Shot
Control Bit
RW
SSC1
Message Slot 1 Single-Shot
Control Bit
RW
SSC0
Message Slot 0 Single-Shot
Control Bit
RW
Function
0: Single-shot mode not used
1: Use single-shot mode
RW
RW
NOTES:
1. Set the CiSSCTLR register after the CiMCTLj register (j=0 to 15) in a slot corresponding to the bit to be
changed is set to "0016".
2. The CiSSCTLR register can be accessed only when the BANKSEL bit in the CiCTLR1 register is set to
"0" (message slot control register and single-shot register selected).
3. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after reset
and supplying a clock to the CAN module, and setting the BANKSEL bit to "0".
Figure 22.20 C0SSCTLR, C1SSCTLR and C2SSCTLR Registers
According to the CAN Specification 2.0 Part B, if the arbitration lost or transmission error causes a
transmit failure, the microcomputer continues transmitting data until the transmission is completed. The
CiSSCTLR register determines whether or not, and from which slot, data is re-transmitted.
In single-shot mode, if the arbitration lost or transmission error causes a transmission failure, data is not
transmitted again. When the SSCj bit (j=0 to 15) is set to "1", the corresponding message slot j is in
single-shot mode.
Rev. 1.10 Oct. 18, 2005 Page 318 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.18 CANi Single-Shot Status Register (CiSSSTR Register) (i=0 to 2)
CANi Single-Shot Status Register (i=0 to 2)(1)
b15
b8 b7
b0
Symbol
Address
After Reset(2)
C0SSSTR
C1SSSTR
022516 - 022416
02A516 - 02A416
000016
000016
C2SSSTR
01C516 - 01C416
000016
Bit
Symbol
Bit Name
SSS15
Message Slot 15 Single-Shot
Status Bit(3)
SSS14
Function
0: No arbitration is lost, or no
transmit error occurs
Message Slot 14 Single-Shot 1: Arbitration is lost, or transmit
error occurs
Status Bit(3)
RW
RW
RW
SSS13
Message Slot 13 Single-Shot
Status Bit(3)
RW
SSS12
Message Slot 12 Single-Shot
Status Bit(3)
RW
SSS11
Message Slot 11 Single-Shot
Status Bit(3)
RW
SSS10
Message Slot 10 Single-Shot
Status Bit(3)
RW
SSS9
Message Slot 9 Single-Shot
Status Bit(3)
RW
SSS8
Message Slot 8 Single-Shot
Status Bit(3)
RW
SSS7
Message Slot 7 Single-Shot
Status Bit(3)
RW
SSS6
Message Slot 6 Single-Shot
Status Bit(3)
RW
SSS5
Message Slot 5 Single-Shot
Status Bit(3)
RW
SSS4
Message Slot 4 Single-Shot
Status Bit(3)
RW
SSS3
Message Slot 3 Single-Shot
Status Bit(3)
RW
SSS2
Message Slot 2 Single-Shot
Status Bit(3)
RW
SSS1
Message Slot 1 Single-Shot
Status Bit(3)
RW
SSS0
Message Slot 0 Single-Shot
Status Bit(3)
RW
NOTES:
1. The CiSSSTR register can be accessed when the BANKSEL bit in the CiCTLR1 is set to "0".
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after reset
and supplying a clock to the CAN module, and setting the BANKSEL bit to "0".
3. Set to "0" by program. When it is set it to "1", the value before setting to "1" remains.
Figure 22.21 C0SSSTR, C1SSSTR and C2SSSTR Registers
If the arbitration lost or transmission error causes a transmission failure, the bit corresponding to message slot j (j=0 to 15) is set to "1". The SSSj bit is set to "0" by program because it is not set to "0"
automatically.
Use the MOV instruction, instead of the bit clear instruction, to set the SSSj bit to "0". Bits not being
changed to "0" must be set to "1".
For example: To set the SSS0 bit for CAN0 to "0"
Assembly language:
mov.w #07FFFh, C0SSSTR
C language:
c0ssstr = 0x7FFF;
Rev. 1.10 Oct. 18, 2005 Page 319 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.19 CANi Global Mask Register, CANi Local Mask Register A and CANi Local Mask
Register B (CiGMRk, CiLMARk and CiLMBRk Registers) (i=0 to 2, k=0 to 4)
CANi Global Mask Register Standard ID0(1)
CANi Local Mask Register A Standard ID0(1)
CANi Local Mask Register B Standard ID0(1) (i=0 to 2)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
After Reset(2)
C0GMR0, C1GMR0, C2GMR0
C0LMAR0, C1LMAR0, C2LMAR0
022816, 02A816, 01C816
023016(3), 02B016(4), 01D016(5)
XXX0 00002
XXX0 00002
C0LMBR0, C1LMBR0, C2LMBR0
023816(6), 02B816(7), 01D816(8)
XXX0 00002
Bit
Symbol
Bit Name
Function
RW
SID6M Standard ID6
RW
SID7M Standard ID7
RW
SID8M Standard ID8
0: No ID is checked
1: ID is checked
RW
SID9M Standard ID9
RW
SID10M Standard ID10
RW
Nothing is assigned. When write, set to "0".
(b7 - b5) When read, its content is indeterminate.
NOTES:
1. This register can be accessed when the BANKSEL bit in the CiCTLR1 register is set to "1".
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset, supplying a clock to the CAN module, and setting the BANKSEL bit to "1".
3. The C0LMAR0 register shares the same address with the C0MCTL0 register.
4. The C1LMAR0 register shares the same address with the C1MCTL0 register.
5. The C2LMAR0 register shares the same address with the C2MCTL0 register.
6. The C0LMBR0 register shares the same address with the C0MCTL8 register.
7. The C1LMBR0 register shares the same address with the C1MCTL8 register.
8. The C2LMBR0 register shares the same address with the C2MCTL8 register.
Figure 22.22 C0GMR0, C0LMAR0 and C0LMBR0 Registers
C1GMR0, C1LMAR0 and C1LMBR0 Registers
C2GMR0, C2LMAR0 and C2LMBR0 Registers
Rev. 1.10 Oct. 18, 2005 Page 320 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
CANi Global Mask Register Standard ID1(1)
CANi Local Mask Register A Standard ID1(1)
CANi Local Mask Register B Standard ID1(1) (i=0 to 2)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
C0GMR1, C1GMR1, C2GMR1
Address
022916, 02A916, 01C916
After Reset(2)
XX00 00002
C0LMAR1, C1LMAR1, C2LMAR1 023116(3), 02B116(4), 01D116(5) XX00 00002
C0LMBR1, C1LMBR1, C2LMBR1 023916(6), 02B916(7), 01D916(8) XX00 00002
Bit
Symbol
Bit Name
Function
RW
SID0M
Standard ID0
RW
SID1M
Standard ID1
RW
SID2M
Standard ID2
RW
0: No ID is verified
1: ID is verified
SID3M
Standard ID3
RW
SID4M
Standard ID4
RW
SID5M
Standard ID5
RW
Nothing is assigned. When write, set to "0".
(b7 - b6) When read, its content is indeterminate.
NOTES:
1. The CiGMR0, CiLMAR0 and CiLMBR0 registers can be accessed only when the BANKSEL bit in
the CiCTLR1 register is set to "1" (mask register selected).
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset, supplying a clock to the CAN module, and setting the BANKSEL bit to "1".
3. The C0LMAR1 register shares the same address with the C0MCTL1 register.
4. The C1LMAR1 register shares the same address with the C1MCTL1 register.
5. The C2LMAR1 register shares the same address with the C2MCTL1 register.
6. The C0LMBR1 register shares the same address with the C0MCTL9 register.
7. The C1LMBR1 register shares the same address with the C1MCTL9 register.
8. The C2LMBR1 register shares the same address with the C2MCTL9 register.
Figure 22.23 C0GMR1, C0LMAR1 and C0LMBR1 Registers
C1GMR1, C1LMAR1 and C1LMBR1 Registers
C2GMR1, C2LMAR1 and C2LMBR1 Registers
Rev. 1.10 Oct. 18, 2005 Page 321 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
CANi Global Mask Register Extended ID0(1)
CANi Local Mask Register A Extended ID0(1)
CANi Local Mask Register B Extended ID0(1) (i=0 to 2)
b7
b6
b5
b4
b3
b2
b1
b0
After Reset(2)
Symbol
Address
C0GMR2, C1GMR2, C2GMR2
C0LMAR2, C1LMAR2, C2LMAR2
C0LMBR2, C1LMBR2, C2LMBR2
022A16, 02AA16, 01CA16
XXXX 00002
023216(3), 02B216(4), 01D216(5) XXXX 00002
023A16(6), 02BA16(7), 01DA16(8) XXXX 00002
Bit
Symbol
Bit Name
Function
RW
RW
EID14M Extended ID14
EID15M Extended ID15
RW
0: No ID is checked
1: ID is checked
EID16M Extended ID16
RW
EID17M Extended ID17
RW
Nothing is assigned. When write, set to "0".
(b7 - b4) When read, its content is indeterminate.
NOTES:
1. This register can be accessed when the BANKSEL bit in the CiCTLR1 register is set to "1".
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset, supplying a clock to the CAN module, and setting the BANKSEL bit to "1".
3. The C0LMAR2 register shares the same address with the C0MCTL2 register.
4. The C1LMAR2 register shares the same address with the C1MCTL2 register.
5. The C2LMAR2 register shares the same address with the C2MCTL2 register.
6. The C0LMBR2 register shares the same address with the C0MCTL10 register.
7. The C1LMBR2 register shares the same address with the C1MCTL10 register.
8. The C2LMBR2 register shares the same address with the C2MCTL10 register.
Figure 22.24 C0GMR2, C0LMAR2 and C0LMBR2 Registers
C1GMR2, C1LMAR2 and C1LMBR2 Registers
C2GMR2, C2LMAR2 and C2LMBR2 Registers
Rev. 1.10 Oct. 18, 2005 Page 322 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
CANi Global Mask Register Extended ID1(1)
CANi Local Mask Register A Extended ID1(1)
CANi Local Mask Register B Extended ID1(1) (i=0 to 2)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
C0GMR3, C1GMR3, C2GMR3
C0LMAR3, C1LMAR3, C2LMAR3
C0LMBR3, C1LMBR3, C2LMBR3
Bit
Symbol
Bit Name
Address
022B16, 02AB16, 01CB16
023316(3), 02B316(4), 01D316(5)
023B16(6), 02BB16(7), 01DB16(8)
After Reset(2)
0016
0016
0016
Function
RW
EID6M
Extended ID6
RW
EID7M
Extended ID7
RW
EID8M
Extended ID8
RW
EID9M
Extended ID9
RW
0: No ID is checked
1: ID is checked
EID10M Extended ID10
RW
EID11M Extended ID11
RW
EID12M Extended ID12
RW
EID13M Extended ID13
RW
NOTES:
1. This register can be accessed when the BANKSEL bit in the CiCTLR1 register is set to "1".
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset, supplying a clock to the CAN module, and setting the BANKSEL bit to "1".
3. The C0LMAR3 register shares the same address with the C0MCTL3 register.
4. The C1LMAR3 register shares the same address with the C1MCTL3 register.
5. The C2LMAR3 register shares the same address with the C2MCTL3 register.
6. The C0LMBR3 register shares the same address with the C0MCTL11 register.
7. The C1LMBR3 register shares the same address with the C1MCTL11 register.
8. The C2LMBR3 register shares the same address with the C2MCTL11 register.
Figure 22.25 C0GMR3, C0LMAR3 and C0LMBR3 Registers
C1GMR3, C1LMAR3 and C1LMBR3 Registers
C2GMR3, C2LMAR3 and C2LMBR3 Registers
Rev. 1.10 Oct. 18, 2005 Page 323 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
CANi Global Mask Register Extended ID2(1)
CANi Local Mask Register A Extended ID2(1)
CANi Local Mask Register B Extended ID2(1) (i=0 to 2)
b7
b6
b5
b4
b3
b2
b1
b0
After Reset(2)
XX00 00002
Symbol
C0GMR4, C1GMR4, C2GMR4
Address
022C16, 02AC16, 01CC16
C0LMAR4, C1LMAR4, C2LMAR4
C0LMBR4, C1LMBR4, C2LMBR4
023416(3), 02B416(4), 01D416(5) XX00 00002
023C16(6), 02BC16(7), 01DC16(8) XX00 00002
Bit
Symbol
Bit Name
Function
RW
EID0M
Extended ID0
RW
EID1M
Extended ID1
RW
EID2M
Extended ID2
RW
0: No ID is checked
1: ID is checked
EID3M
Extended ID3
RW
EID4M
Extended ID4
RW
EID5M
Extended ID5
RW
Nothing is assigned. When write, set to "0".
(b7 - b6) When read, its content is indeterminate.
NOTES:
1. This register can be accessed when the BANKSEL bit in the CiCTLR1 register is set to "1".
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset, supplying a clock to the CAN module, and setting the BANKSEL bit to "1".
3. The C0LMAR4 register shares the same address with the C0MCTL4 register.
4. The C1LMAR4 register shares the same address with the C1MCTL4 register.
5. The C2LMAR4 register shares the same address with the C2MCTL4 register.
6. The C0LMBR4 register shares the same address with the C0MCTL12 register.
7. The C1LMBR4 register shares the same address with the C1MCTL12 register.
8. The C2LMBR4 register shares the same address with the C2MCTL12 register.
Figure 22.26 C0GMR4, C0LMAR4 and C0LMBR4 Registers
C1GMR4, C1LMAR4 and C1LMBR4 Registers
C2GMR4, C2LMAR4 and C2LMBR4 Registers
Rev. 1.10 Oct. 18, 2005 Page 324 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
The CiGMRk, CiLMARk and CiLMBRk registers are used for acceptance filtering. The users can
select and receive user-desired messages.
The CiGMRk register determines whether IDs in the message slots 0 to 13 are verified. The CiLMARk
register determines whether ID in the message slot 14 is verified. The CiLMBRk register determines
whether ID in the message slot 15 is verified.
• When bits in these registers are set to "0", each standard ID0 and standard ID1 bits (ID bit) and
extended ID0 to extended ID2 bits in the CANi message slots j (j=0 to 15) corresponding to the bits
in the above registers, is masked while acceptance filtering. (The corresponding bits are assumed
to have matching IDs.)
• When bits in these registers are set to "1", corresponding ID bits are compared with received IDs
while acceptance filtering. If the received ID matches the ID in the message slot j, the received
data having the matched ID is stored into that message slot.
NOTES:
1. Change the CiGMRk register setting only when the message slots 0 to 13 have no receive request.
2. Change the CiLMARk register setting only when the message slot 14 has no receive request.
3. Change the CiLMBRk register setting only when the message slot 15 has no receive request.
4. More than two message slots are able to store a receive message ID, the ID is stored into the
message slot, having the smallest slot number.
Figure 22.27 shows each mask register and corresponding message slot. Figure 22.28 shows the
acceptance filtering.
Rev. 1.10 Oct. 18, 2005 Page 325 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
CiGMARk Regiser
Message Slot 0
to
Message Slot 13
CiLMARk Register
Message Slot 14
CiLMBRk Register
Message Slot 15
i=0 to 2, k=0 to 4
Figure 22.27 Mask Registers and Message Slots
For Standard ID
Receive Message
ID
ID Set in
the Message Slot
Standard ID0
Setting Velue of
the Mask Register
Standard ID0
Value of the Mask Bit
0: Mask a receive message ID, corresponding
to a bit in the maks register
1: Verify whether a recive message ID
matches a corresponding bit
Standard ID0
Standard ID1
Standard ID1
Standard ID1
...
Standard ID10
Standard ID10
Figure 22.28 Acceptance Filtering
Rev. 1.10 Oct. 18, 2005 Page 326 of 435
REJ09B0162-0110
Acceptance Verify
Signal
Standard ID10
Acceptance Verify Signal
0: Received message is ignored
(Message is stored into no message slot)
1: Received message is stored an slot,
having the matched ID
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.20 CANi Message Slot j Control Register (CiMCTLj Register) (i=0 to 2, j=0 to 15)
CANi Message Slot j Control Register (i=0 to 2, j=0 to 15)(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
C0MCTL0 to C0MCTL15
C1MCTL0 to C1MCTL15
C2MCTL0 to C2MCTL15
Bit
Symbol
Bit Name
After Reset(2)
0016
0016
0016
Address
023016 to 023F16(3)
02B016 to 02BF16(4)
01D016 to 01DF16(5)
Function
When receive, Receive Complete When transmitting
NEWDATA Flag(6)
0: Not transmitted
When transmit, Transmit Complete
1: Transmit completed
SENTDATA Flag(6)
When transmitting
When receive,
0: Except transmitting
INVALDATA Receiving Flag
When transmit, Transmitting Flag 1: Transmitting
TRMACTIVE
RW
When receiving
0: Not received
RW
1: Receive completed
When receiving
0: Except storing
received data
1: Storing received data
MSGLOST Overwrite Flag(6) 0: No overrun error occurs
1: Overrun error occurs
In modes other than BasicCan mode
0: Data frame
Remote Frame
1: Remote frame
REMACTIVE Transmit/Receive
In BasicCan mode
Status Flag
0: Receives the data frame (status)
1: Receives the remote frame (status)
0: Enables automatic answering of the remote
Automatic
frame
Answering
RSPLOCK Disable Mode
1: Disables automatic answering of the remote
Select Bit
frame
RO
RW
RO
RW
REMOTE
Remote Frame
Set Bit
0: Transmits/receives the data frame
1: Transmits/receives the remote frame
RW
RECREQ
Receive
Request Bit
0: No request to receive the frame
1: Request to receive the frame
RW
TRMREQ
Transmit
Request Bit
0: No request to transmit the frame
1: Request to transmit the frame
RW
NOTES:
1. This register can be accessed when the BANKSEL bit in the CiCTLR1 register is set to "0".
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset and supplying the clock to the CAN module, and setting the BANKSEL bit to "0" .
3. The C0MCTL0 to C0MCTL4 registers share addresses with the C0LMAR0 to C0LMAR4 registers
respectively. The C0MCTL8 to C0MCTL12 registers share addresses with the C0LMBR0 to
C0LMBR4 registers respectively.
4. The C1MCTL0 to C1MCTL4 registers share addresses with the C1LMAR0 to C1LMAR4 registers
respectively. The C1MCTL8 to C1MCTL12 registers share addresses with the C1LMBR0 to
C1LMBR4 registers respectively.
5. The C2MCTL0 to C2MCTL4 registers share addresses with the C2LMAR0 to C2LMAR4 registers
respectively. The C2MCTL8 to C2MCTL12 registers share addresses with the C2LMBR0 to
C2LMBR4 registers respectively.
6. Set to "0" by program. If it is set to "1", the value before setting to "1" remains.
Figure 22.29 C0MCTL0 to C0MCTL15 Registers, C1MCTL0 to C1MCTL15 Registers and
C2MCTL0 to C2MCTL15 Registers
Rev. 1.10 Oct. 18, 2005 Page 327 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
Table 22.4 CiMCTLj register(i=0 to 2, j= 0 to 15) Settings and Transmit/Receive Mode
Settings for the CiMCTLj Register
TRMREQ RECREQ REMOTE RSPLOCK REMACTIVE MSGLOST TRMACTIVE SENTDATA Transmit/Receive Mode
INVALDATA NEWDATA
0
0
0
0
1
1
0
0
1
1
1
0
0
0
1
0
0
1
or
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
No frame is transmitted or received
Data frame is received
Remote frame is received
(The data frame is transmitted
after receiving the remote frame.)
Data frame is transmitted
Remote frame is transmitted
(The data frame is received after
transmitting the remote frame)
22.1.20.1 SENTDATA/NEWDATA Bit
The SENTDATA/NEWDATA bit indicates that the CAN module has transmitted or received the CAN
message. Set the SENTDATA/NEWDATA bit to "0 " (not transmitted or not received) by program
before data transmission and reception is started. The SENTDATA/NEWDATA bit is not set to "0"
automatically. When the TRMACTIVE/INVALDATA bit is set to "1" (during transmission or storing
received data), the SENTDATA/NEWDATA bit cannot be set to "0".
SENTDATA : The SENTDATA bit is set to "1" (transmit complete) when data transmission is completed in the transmit message slot.
NEWDATA :
The NEWDATA bit is set to "1" (receive complete) when the message to be stored
into the message slot j (j=0 to 15) is received in the receive message slot as expected.
NOTES:
1. To read a received data from the message slot j, set the NEWDATA bit to "0" before reading. If
the NEWDATA bit is set to "1" immediately after reading, this indicates that new received data
has been stored into the message slot while reading and the read data contains an indeterminate value. In this case, discard the data with indeterminate value and then read the message
slot again after the NEWDATA bit is set to "0".
2. When the remote frame is transmitted or received, the SENTDATA/NEWDATA bit remains
unchanged after the remote frame transmission or reception is completed. The SENTDATA/
NEWDATA bit is set to "1" when a subsequent data frame transmission or reception is completed.
22.1.20.2 TRMACTIVE/INVALDATA Bit
The TRMACTIVE/INVALDATA bit indicates that the CAN protcol controller is transmitting or receiving
a message and accessing the message slot j. The TRMACTIVE/INVALDATA bit is set to "1" when the
CAN module is accessing the message slot and to "0 " when not accessing the message slot.
TRMACTIVE : The TRMACTIVE bit is set to "1" (except transmitting) when a data transmission is
started in the message slot. If the CAN module loses in bus arbitration, the
TRMACTIVE bit is set to "0" (stops transmitting) when a CAN bus error occurs or
when a data transmission is completed.
INVALDATA : The INVALDATA bit is set to "1" (storing received data) when receiving a received
message into the messaqe slot j, after a message reception is completed. Then the
INVALDATA bit is set to "0" after a message storage is completed. Data, if read
from the message slot j while this bit is set to "1", is indeterminate.
Rev. 1.10 Oct. 18, 2005 Page 328 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
22.1.20.3 MSGLOST Bit
The MSGLOST bit is enabled only when the message slot is set for reception. The MSGLOST bit is set
to "1" (overrun error occurred) when the message slot j is overwritten by a new received message
while the NEWDATA bit set to "1" (already received).
The MSGLOST bit is not automatically set to "0". Set to "0" (no overrun error occurred) by program.
22.1.20.4 REMACTIVE Bit
The CiMCTL0 to CiMCTL15 registers all have the same function when the STATE_BASICCAN bit is
set to "0" (other than BasicCAN mode).
The REMACTIVE bit is set to "1" (remote frame) when the message slot j is set to transmit or receive
the remote frame. The REMACTIVE bit is set to "0" (data frame) after the remote frame has been
transmitted or received.
The functions of the CiMCTL14 and CiMCTL15 registers change when the STATE_BASICCAN bit is
set to "1" (BasicCAN mode). When the REMACTIVE bit is set to "0", this indicates that a message
stored into the message slot is the data frame. When the REMACTIVE bit is set to "1", this indicates a
message stored into the message slot is the remote frame.
22.1.20.5 RSPLOCK Bit
The RSPLOCK bit is enabled only when remote frame reception shown in Table 22.4 is selected. The
RSPLOCK bit determines whether the received remote frame is processed or not.
When the RSPLOCK bit is set to "0" (automatic answering of the remote frame enabled), the slot
automatically changes to a transmit slot after the remote frame is received and the message stored
into the message slot is automatically transmitted as the data frame.
When the RSPLOCK bit is set to "1" (automatic answering of the remote frame disabled), message is
not automatically transmitted upon receiving the remote frame.
Set the RSPLOCK bit to "0" to select any transmit/receive mode other than the remote frame reception.
22.1.20.6 REMOTE Bit
The REMOTE bit selects transmit/receive mode shown in Table 22.4. Set the REMOTE bit to "0" to
transmit or receive data frame. Set to "1" to transmit or receive remote frame.
The followings occur during remote frame transmission or reception.
• Transmitting the remote frame
A message stored into the message slot j (j=0 to 15) is transmitted as the remote frame. After
transmission, the slot automatically becomes ready to receive data frame.
If the data frame is received before the remote frame is transmitted, the data frame is stored into
the message slot j. The remote frame is not transmitted.
• Receiving the remote frame
The message slot receives the remote frame. The RSPLOCK bit determines whether or not to
process the received remote frame.
Rev. 1.10 Oct. 18, 2005 Page 329 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
22.1.20.7 RECREQ Bit
The RECREQ bit selects transmit/receive mode shown in Table 22.4. Set the RECREQ bit to "1"
(receive requested) when data frame or remote frame is received. Set the RECREQ bit to "0" (no
receive requested) when data frame or remote frame is transmitted.
When a data frame is automatically transmitted after a remote frame is received, the RECREQ bit
remains set to "1". Set the RECREQ bit to "0" to transmit a remote frame. After a remote frame is
transmitted, a data frame is automatically received while the RECREQ bit remains set to "0".
When setting the TRMREQ bit to "1" (transmit requested), do not set the RECREQ bit to "1" (receive
requested).
22.1.20.8 TRMREQ Bit
The TRMREQ bit selects transmit/receive mode shown in Table 22.4. Set the TRMREQ bit to "1"
(transmit requested) when data frame or remote frame is transmitted.
Set the TRMREQ bit to "0" (no request to transmit the frame) when data frame or remote frame is
received.
When the data frame is automatically received after the remote frame is transmitted, the TRMREQ bit
remains set to "1". Set the TRMREQ bit to "0" to receive the remote frame. After the remote frame is
received, data frame is automatically transmitted while the TRMREQ bit remains set to "0".
If the RECREQ bit is set to "1" (request to receive the frame), do not set the TRMREQ bit to "1" (
request to transmit the frame).
NOTES:
1. If some message slots are requested to transmit the data frame or remote frame, the message
slot, having the smallest slot number starts transmitting.
2. In single-shot mode, the CiMCTLj register is set to "0016" when data transmission is failed, due
to the arbitration lost or transmission error.
Rev. 1.10 Oct. 18, 2005 Page 330 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.21 CANi Slot Buffer Select Register (CiSBS Register) (i=0 to 2)
CANi Slot Buffer Select Register (i=0 to 2)
b7
b6
b5
b4
b3
b2
b1
Symbol
C0SBS
C1SBS
C2SBS
b0
Bit
Symbol
After Reset(2)
0016
0016
0016
Address
024016
025016
017016
Bit Name
RW
Function
b3 b2 b1 b0
SBS00
SBS01
SBS02
CANi Message
Slot Buffer 0
Number Select Bit
SBS03
0
0
0
0
0
0
0
0
0
0
1
1
0:
1:
0:
1:
Message slot 0
Message slot 1
Message slot 2
Message slot 3
RW
RW
(Note 1)
1
1
1
1
1
1
1
1
0
0
1
1
0:
1:
0:
1:
Message slot 12
Message slot 13
Message slot 14
Message slot 15
RW
RW
RW
b3 b2 b1 b0
SBS10
SBS11
SBS12
CANi Message
Slot Buffer 1
Number Select Bit
SBS13
0
0
0
0
0
0
0
0
0
0
1
1
0:
1:
0:
1:
Message slot 0
Message slot 1
Message slot 2
Message slot 3
1
1
1
1
1
1
1
1
0
0
1
1
0:
1:
0:
1:
Message slot 12
Message slot 13
Message slot 14
Message slot 15
RW
(Note 1)
RW
RW
NOTES:
1. 16 CANi message slots are provided. Each message slot can be selected as a transmit or a receive
slot.
2. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) after
reset and supplying a clock to the CAN module.
Figure 22.30 C0SBS, C1SBS and C2SBS Registers
22.1.21.1 SBS03 to SBS00 Bits
If the SBS03 to SBS00 bits select a number j (j=0 to 15), the message slot j is allocated to the CANi
message slot buffer 0. The message slot j can be accessed via addresses 01E016 to 01EF16, and
026016 to 026F16.
22.1.21.2 SBS13 to SBS10 Bits
If the SBS13 to SBS10 bits select a number j, the message slot j is allocated to the CANi message slot
buffer 1. The message slot j can be accessed via addresses 01F016 to 01FF16, and 027016 to 027F16.
Rev. 1.10 Oct. 18, 2005 Page 331 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.22 CANi Message Slot Buffer j (i=0 to 2, j=0,1)
CANi Message Slot Buffer j Standard ID0 (i=0 to 2, j=0,1)(1)
b7
b6
b5
b4
b3
b2
b1
Symbol
C0SLOT0_0, C0SLOT1_0
C1SLOT0_0, C1SLOT1_0
C2SLOT0_0, C2SLOT1_0
b0
Bit
Symbol
Address
01E016, 01F016
026016, 027016
018016, 019016
Bit Name
After Reset
Indeterminate
Indeterminate
Indeterminate
Function
RW
SID6
Standard ID6
Read or write the standard ID6
in the message slot k (k=0 to 15)
RW
SID7
Standard ID7
Read or write the standard ID7
in the message slot k
RW
SID8
Standard ID8
Read or write the standard ID8
in the message slot k
RW
SID9
Standard ID9
Read or write the standard ID9
in the message slot k
RW
SID10
Standard ID10
Read or write the standard ID10
in the message slot k
RW
Nothing is assigned. When write, set to "0".
(b7 - b5) When read, its content is indeterminate.
NOTE:
1. Select, by setting the CiSBS register, the message slot k to be accessed by the CiSLOTj_0 register.
CANi Message Slot Buffer j Standard ID1 (i=0 to 2, j=0,1)(1)
b7
b6
b5
b4
b3
b2
b1
Symbol
C0SLOT0_1, C0SLOT1_1
C1SLOT0_1, C1SLOT1_1
C2SLOT0_1, C2SLOT1_1
b0
Bit
Symbol
Bit Name
Address
01E116, 01F116
026116, 027116
018116, 019116
After Reset
Indeterminate
Indeterminate
Indeterminate
Function
RW
SID0
Standard ID0
Read or write the standard ID0
in the message slot k (k=0 to 15)
RW
SID1
Standard ID1
Read or write the standard ID1
in the message slot k
RW
SID2
Standard ID2
Read or write the standard ID2
in the message slot k
RW
SID3
Standard ID3
Read or write the standard ID3
in the message slot k
RW
SID4
Standard ID4
Read or write the standard ID4
in the message slot k
RW
SID5
Standard ID5
Read or write the standard ID5
in the message slot k
RW
Nothing is assigned. When write, set to "0".
(b7 - b6) When read, its content is indeterminate.
NOTE:
1. Select, by setting the CiSBS register, the message slot k to be accessed by the CiSLOTj_1 register.
Figure 22.31 C0SLOT0_0, C0SLOT1_0, C0SLOT0_1 and C0SLOT1_1 Registers
C1SLOT0_0, C1SLOT1_0, C1SLOT0_1 and C1SLOT1_1 Registers
C2SLOT0_0, C2SLOT1_0, C2SLOT0_1 and C2SLOT1_1 Registers
Rev. 1.10 Oct. 18, 2005 Page 332 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
CANi Message Slot Buffer j Extended ID0 (i=0 to 2, j=0,1)(1, 2)
b7
b6
b5
b4
b3
b2
b1
Symbol
C0SLOT0_2, C0SLOT1_2
b0
C1SLOT0_2, C1SLOT1_2
C2SLOT0_2, C2SLOT1_2
Bit
Symbol
Address
01E216, 01F216
026216, 027216
018216, 019216
Bit Name
After Reset
Indeterminate
Indeterminate
Indeterminate
Function
RW
EID14
Extended ID14
Read or write the extended ID14
in the message slot k (k=0 to 15)
RW
EID15
Extended ID15
Read or write the extended ID15
in the message slot k
RW
EID16
Extended ID16
Read or write the extended ID16
in the message slot k
RW
EID17
Extended ID17
Read or write the extended ID17
in the message slot k
RW
Nothing is assigned. When write, set to "0".
(b7 - b4) When read, its content is indeterminate.
NOTES:
1. If the receive slot is standard ID formatted, the EID bits are indeterminate when received data is stored.
2. Select, by setting the CiSBS register, the message slot k to be accessed by the CiSLOTj_2 register.
CANi Message Slot Buffer j Extended ID1
b7
b6
b5
b4
b3
b2
b1
Symbol
C0SLOT0_3, C0SLOT1_3
C1SLOT0_3, C1SLOT1_3
C2SLOT0_3, C2SLOT1_3
b0
Bit
Symbol
Bit Name
(i=0 to 2, j=0,1)(1, 2)
Address
01E316, 01F316
026316, 027316
018316, 019316
After Reset
Indeterminate
Indeterminate
Indeterminate
Function
RW
EID6
Extended ID6
Read or write the extended ID6
in the message slot k (k=0 to 15)
RW
EID7
Extended ID7
Read or write the extended ID7
in the message slot k
RW
EID8
Extended ID8
Read or write the extended ID8
in the message slot k
RW
EID9
Extended ID9
Read or write the extended ID9
in the message slot k
RW
EID10
Extended ID10
Read or write the extended ID10
in the message slot k
RW
EID11
Extended ID11
Read or write the extended ID11
in the message slot k
RW
EID12
Extended ID12
Read or write the extended ID12
in the message slot k
RW
EID13
Extended ID13
Read or write the extended ID13
in the message slot k
RW
NOTES:
1. If the receive slot is standard ID formatted, the EID bits are indeterminate when received data is stored.
2. Select, by setting the CiSBS register, the message slot k to be accessed by the CiSLOTj_3 register.
Figure 22.32 C0SLOT0_2, C0SLOT1_2, C0SLOT0_3 and C0SLOT1_3 Registers
C1SLOT0_2, C1SLOT1_2, C1SLOT0_3 and C1SLOT1_3 Registers
C2SLOT0_2, C2SLOT1_2, C2SLOT0_3 and C2SLOT1_3 Registers
Rev. 1.10 Oct. 18, 2005 Page 333 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
CANi Message Slot Buffer j Extended ID2 (i=0 to 2, j=0,1)(1, 2)
b7
b6
b5
b4
b3
b2
b1
Symbol
C0SLOT0_4, C0SLOT1_4
C1SLOT0_4, C1SLOT1_4
b0
C2SLOT0_4, C2SLOT1_4
Bit
Symbol
Address
01E416, 01F416
026416, 027416
018416, 019416
Bit Name
After Reset
Indeterminate
Indeterminate
Indeterminate
Function
RW
EID0
Extended ID0
Read or write the extended ID0
in the message slot k (k=0 to 15)
RW
EID1
Extended ID1
Read or write the extended ID1
in the message slot k
RW
EID2
Extended ID2
Read or write the extended ID2
in the message slot k
RW
EID3
Extended ID3
Read or write the extended ID3
in the message slot k
RW
EID4
Extended ID4
Read or write the extended ID4
in the message slot k
RW
EID5
Extended ID5
Read or write the extended ID5
in the message slot k
RW
Nothing is assigned. When write, set to "0".
(b7 - b6) When read, its content is indeterminate.
NOTES:
1. If the receive slot is standard ID formatted, the EID bits are indeterminate when received data is stored.
2. Select, by setting the CiSBS register, the message slot k to be accessed by the CiSLOTj_4 register.
CANi Message Slot Buffer j Data Length Code (i=0 to 2, j=0,1)(1)
b7
b6
b5
b4
b3
b2
b1
Symbol
C0SLOT0_5, C0SLOT1_5
b0
After Reset
C1SLOT0_5, C1SLOT1_5
Address
01E516, 01F516
026516, 027516
C2SLOT0_5, C2SLOT1_5
018516, 019516
Indeterminate
Bit
Symbol
Bit Name
Indeterminate
Indeterminate
Function
DLC0
RW
RW
DLC1
RW
Data Length Set Bit
Read or write the data length set bit
in the message slot k (k=0 to 15)
DLC2
RW
DLC3
RW
Nothing is assigned. When write, set to "0".
(b7 - b4) When read, its content is indeterminate.
NOTE:
1. Select, by setting the CiSBS register, the message slot k to be accessed by the CiSLOTj_5 register.
Figure 22.33 C0SLOT0_4, C0SLOT1_4, C0SLOT0_5 and C0SLOT1_5 Registers
C1SLOT0_4, C1SLOT1_4, C1SLOT0_5 and C1SLOT1_5 Registers
C2SLOT0_4, C2SLOT1_4, C2SLOT0_5 and C2SLOT1_5 Registers
Rev. 1.10 Oct. 18, 2005 Page 334 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
CANi Message Slot Buffer j Data m (i=0 to 2, j=0,1, m=0 to 7)(1, 2)
b7
Symbol
C0SLOT0_6 to C0SLOT0_13
C0SLOT1_6 to C0SLOT1_13
C1SLOT0_6 to C1SLOT0_13
C1SLOT1_6 to C1SLOT1_13
C2SLOT0_6 to C2SLOT0_13
C2SLOT1_6 to C2SLOT1_13
b0
Address
01E616 to 01ED16
01F616 to 01FD16
026616 to 026D16
027616 to 027D16
018616 to 018D16
019616 to 019D16
Function
After Reset
Indeterminate
Indeterminate
Indeterminate
Indeterminate
Indeterminate
Indeterminate
Setting Range
Read or write data m in the message slot k
(k=0 to 15, m=0 to 7)
0016 to FF16
RW
RW
NOTES:
1. Select, by setting the CiSBS register, the data m in the message slot k to be accessed by the
CiSLOTj_6 to CiSLOTj_13 register.
2. When the data frame is received, data with lessthan the data length selected by the CiSLOTj_5
register is indeterminate.
CANi Message Slot Buffer j Time Stamp High-Ordered (i=0,1, j=0,1)(1)
b7
Symbol
C0SLOT0_14, C0SLOT1_14
b0
C1SLOT0_14, C1SLOT1_14
C2SLOT0_14, C2SLOT1_14
Address
01EE16, 01FE16
026E16, 027E16
018E16, 019E16
Function
Read or write the time stamp high-ordered
in the message slot k (k=0 to 15)
After Reset
Indeterminate
Indeterminate
Indeterminate
Setting Range
RW
0016 to FF16
RW
NOTE:
1. Select, by setting the CiSBS register, the time stamp high-ordered in the message slot k to be
accessed by the CiSLOTj_14 register.
CANi Message Slot Buffer j Time Stamp Low-Ordered (i=0 to 2, j=0,1)(1)
b7
Symbol
C0SLOT0_15, C0SLOT1_15
C1SLOT0_15, C1SLOT1_15
C2SLOT0_15, C2SLOT1_15
b0
Address
01EF16, 01FF16
026F16, 027F16
018F16, 019F16
Function
Read or write the time stamp low-ordered
in the message slot k (k=0 to 15)
After Reset
Indeterminate
Indeterminate
Indeterminate
Setting Range
RW
0016 to FF16
RW
NOTE:
1. Select, by setting the CiSBS register, the time stamp low-ordered in the message slot k to be
accessed by the CiSLOTj_15 register.
Figure 22.34 C0SLOT0_6 to C0SLOT0_13, C0SLOT1_6 to C0SLOT1_13, C0SLOT0_14,
C0SLOT1_14, C0SLOT0_15 and C0SLOT1_15 Registers
C1SLOT0_6 to C1SLOT0_13, C1SLOT1_6 to C1SLOT1_13, C1SLOT0_14,
C1SLOT1_14, C1SLOT0_15 and C1SLOT1_15 Registers
C2SLOT0_6 to C2SLOT0_13, C2SLOT1_6 to C2SLOT1_13, C2SLOT0_14,
C2SLOT1_14, C2SLOT0_15 and C2SLOT1_15 Registers
The message slot, selected by setting the CiSBS register, is read by reading the message slot buffer. A
message can be written in the message slot selected by the CiSBS register if the message is written to
the message slot buffer.
Write to the message slot k (k=0 to 15) while the corresponding CiMCTLk register is set to "0016".
Rev. 1.10 Oct. 18, 2005 Page 335 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.1.23 CANi Acceptance Filter Support Register (CiAFS Register) (i=0 to 2)
CANi Acceptance Filter Support Register (i=0 to 2)
b15
b8
b7
b0
Symbol
Address
After Reset(1)
C0AFS
C1AFS
024516 - 024416
025516 - 025416
010016
C2AFS
017516 - 017416
010016
010016
Function
Generates data to determine a received ID
Setting Range
RW
000016 to FFFF16
RW
NOTE:
1. Value is obtained by setting the SLEEP bit in the CiSLPR register to "1" (sleep mode exited) and
supplying a clock to the CAN module after reset.
b0
b15
Write
SID10 SID9 SID8 SID7 SID6
SID5 SID4 SID3 SID2 SID1 SID0
3-8 decoding
b15
Read
b8
b0
b7
CSID7 CSID6 CSID5 CSID4 CSID3 CSID2 CSID1 CSID0 SID10 SID9 SID8 SID7 SID6 SID5 SID4 SID3
b7
Data used to search a data table is
generated from a received ID in standard format. The table search with this
data determines whether or not a received ID is valid.
Top+0016
Top+0116
Top+DE16
Top+FE16
Top+FF16
b15
b8
b5
b3
b2
b1
b0
7F716 7F616 7F516 7F416 7F316 7F216 7F116 7F016
"0"
"0"
"0"
"0"
"0"
"0"
"0"
"1"
7FF16 7FE16 7FD16 7FC16 7FB16 7FA16 7F916 7F816
"0"
"0"
"1"
"0"
"0"
"0"
"0"
"0"
Bit search information
b7
b0
SID5 SID4 SID3 SID2 SID1 SID0
SID10SID9 SID8 SID7 SID6
0 0 1 1 0 0 1 1 0 0 0 1 1 0 1 1
SID10
SID0
"6"
Received ID
"F"
"3"
1 1 0 1 1 1 1 0 0 1 1
"D"
"E"
"3"
Divide it to 8 bits and 3 bits
8 bits
b15
Read from
the CiAFS register
b4
6F716 6F616 6F516 6F416 6F316 6F216 6F116 6F016
"0"
"0"
"0"
"0"
"1"
"0"
"0"
"0"
Address search information
When a received ID is "6F316"
Write to
the CiAFS register
b6
00716 00616 00516 00416 00316 00216 00116 00016
"0"
"0"
"0"
"0"
"0"
"0"
"1"
"0"
00F16 00E16 00D16 00C16 00B16 00A16 00916 00816
"1"
"0"
"0"
"0"
"0"
"0"
"0"
"0"
b8
3 bits
b7
b0
0 0 0 0 1 0 0 0 1 1 0 1 1 1 1 0
"0816"
"D"
"E"
Bit search information
Bit search information
b7
0116
0216
0416
0816
1016
2016
4016
8016
0
0
0
0
0
0
0
1
b3
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
Address search information
b0
3 low-order bits of received ID
1
0
0
0
0
0
0
0
016
116
216
316
416
516
616
716
Because the value of the
3 bits is 3, b3 in the table
left is 1. (If the value of
the 3 bits is 4, b4 in the
table left is 1.)
i = 0 to 2
Figure 22.35 C0AFS, C1AFS and C2AFS Registers
The CiAFS register enables prompt performance of the table search to determine the varidity of a
received ID. This function is for standard-formatted ID only.
Rev. 1.10 Oct. 18, 2005 Page 336 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.2 CAN Clock
The CAN clock is the operating clock for the CAN module. f1 or fCAN can be selected as the CAN clock.
fCAN has the same frequency as the main clock. The PM25 bit in the PM2 register determines the CAN
clock. Refer to 8. Clock Generation Circuit for details.
22.2.1 Main Clock Direct Mode
fCAN becomes the CAN clock in main clock direct mode. The CAN module must enter main clock direct
mode while the PM25 bit is set to "1" (main clock). Set the PM25 bit in CAN sleep mode.
Set the PM24 bit in the PM2 register to "1" (main clock) before accessing CAN-associated registers in
main clock direct mode. Do not enter wait mode or stop mode when the PM24 bit is set to "1".
Table 22.5 lists CAN clock settings. Figure 22.36 shows a flow chart of accessing procedure for CANassociated registers.
Table 22.5 CAN Clock Settings
CAN
Clock
fCAN
CM0
Register
CM1
Register
CM2
Register
CM07 Bit
CM17 Bit
CM21 Bit
PM24 Bit
PM25 Bit
MCD4 to
MCD0 bits
Main Clock
(Main Clock Direct Mode)
0
1
0
1
1
---
Main Clock
0
0
0
0
0
100102
PLL Clock
0
1
0
0
0
100102
PM2 Register
MCD
Register
Clock Source
f1
Start
Set the PM24 bit in the PM2 register
to "1" (main clock)
Wait until a clock oscillation stabilized
Access to CAN-associated registers
Set the PM24 bit to "0" (clock selected
by the CM07 bit in the CM0 register)
End
NOTE:
1. Waiting time varies depending on the CPU clock frequency before or after PM24 bit
setting is changed.
- High Frequency: Higher frequency compared "before PM24 bit setting changes" with
"after PM24 bit setting changes"
- Low Frequency: Lower frequency compared "before PM24 bit setting changes" with
"after PM24 bit setting changes"
2 x High frequency
Low frequency
cycles
Figure 22.36 Accessing Procedure for CAN-Associated Registers
Rev. 1.10 Oct. 18, 2005 Page 337 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
22.3 Timing with CAN-Associated Registers
22.3.1 CAN Module Reset Timing
Figure 22.37 shows an operation example of when the CAN module is reset.
(1) The CAN module can be reset when the STATE_RESET bit in the CiSTR register (i=0 to 2) is set to "1"
(CAN module reset completed) after the RESET1 and RESET0 bits in the CiCTLR0 register are set to
"1" (CAN module reset).
(2) Set necessary CAN-associated registers.
(3) CAN communication can be established after the STATE_RESET bit is set to "0" (resetting) after
the RESET1 and RESET0 bits are set to "0" (CAN module reset exited) .
Set to "1" by program
simultaneously
RESET0 bit
Set to "0" by program
simultaneously
"1"
"0"
RESET1 bit
STATE_RESET bit
"1"
"0"
"1"
Initial Setting for the CAN
Module
"0"
CAN Operation
Verify the STATE_RESET bit
Verify the STATE_RESET bit
Operation (1)
Operation (2)
Operation (3)
Figure 22.37 Example of CAN Module Reset Operation
22.3.2 CAN Transmit Timing
Figure 22.38 shows an operation example of when the CAN transmits a frame.
(1) When the TRMREQ bit in the CiMCTLj register (j=0 to 15) is set to "1" (request to transmit the data
frame) while the CAN bus is in an idle state, the TRMACTIVE bit in the CiMCTLj register is set to
"1" (during transmission) and the TRMSTATE bit in the CiSTR register is set to "1" (during transmission). The CAN starts transmitting the frame.
(2) After a CAN frame transmission is completed, the SENTDATA bit in the CiMCTLj register is set to "1"
(already transmitted), the TRMSUCC bit in the CiSTR register to "1" (transmission completed) and the
SISj bit in the CiSISTR register to "1" (interrupt requested). The MBOX3 to MBOX0 bits in the CiSTR
register store transmitted message slot numbers.
Rev. 1.10 Oct. 18, 2005 Page 338 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
Start transmtting
Transmission completed
(2)
Intermission field
(1)
CAN bus
Bus idle
Bus idle
Transmit frame
"1"
SENTDATA bit
"0"
TRMACTIVE bit
TRMREQ bit
Transmit frame
"1"
Set to "1" by program
"0"
"1"
Transmission-completed
message slot number
"0"
MBOX3 to
MBOX0 bits
TRMSUCC bit
"1"
"0"
TRMSTATE bit
"1"
SISj bit
"1"
j=0 to 15
"0"
"0"
Figure 22.38 Example of CAN Data Frame Transmit Operation
22.3.3 CAN Receive Timing
Figure 22.39 shows an operation example of when the CAN receives a frame.
(1) When the RECREQ bit in the CiMCTLj register (i=0 to 2, j= 0 to 15) is set to "1" (receive requested), the CAN is ready to receive the frame at anytime.
(2) When the CAN starts receiving the frame, the RECSTATE bit in the CiSTR register is set to "1"
(during reception).
(3) After the CAN frame reception is completed, the INVALDATA bit in the CiMCTLj register is set to
"1" (storing received data), the NEWDATA bit in the CiMCTLj register is set to "1" (receive complete) and the RECSUCC bit in the CiSTR register is set to "1" (reception completed).
(4) After data is written to the message slot, the INVALDATA bit is set to "0" (storing receiving data)
and the SISj bit in the CiSISTR register is set to "1" (interrupt requested). The MBOX3 to MBOX0
bits in the CiSTR register store received message slot numbers.
Start
receiving
(1)
CAN bus
(2)
Bus idle
NEWDATA bit
"1"
INVALDATA bit
"1"
RECREQ bit
"1"
Reception
completed
Receive frame
(3)
Receive frame
Bus idle
"0"
"0"
"0"
Set to "1" by program
MBOX3 to
MBOX0 bits
RECSUCC bit
"1"
RECSTATE bit
"1"
SISj bit
"1"
j=0 to 15
Intermission field
(4)
"0"
"0"
"0"
Figure 22.39 Example of CAN Data Frame Receive Operation
Rev. 1.10 Oct. 18, 2005 Page 339 of 435
REJ09B0162-0110
Reception-completed
message slot number
22. CAN Module
M32C/88 Group (M32C/88T)
22.3.4 CAN Bus Error Timing
Figure 22.40 shows an operation example of when a CAN bus error occurs.
(1) When a CAN bus error is detected, the STATE_BUSERROR bit in the CiSTR register is set to "1",
(error occurred) and the BEIS bit in the CiEISTR register is set to "1" (interrupt requested). The
CAN starts transmitting the error frame.
(1)
CAN bus
STATE_BUSERROR
bit
BEIS bit
Transmit / receive frame
Error detected
Error frame
"1"
"0"
"1"
"0"
Figure 22.40 Operation Timing when CAN Bus Error Occurs
22.4 CAN Interrupts
The CANi wake-up interrupt and CANij interrupts (i=0 to 2, j=0 to 2) are provided as the CAN interrupt.
22.4.1 CANi Wake-Up Interrupt
22.4.1.1 CAN0 Wake-Up Interrupt
If P77 (CAN0IN/CAN02IN) is used as a CAN input port, the CAN0 wake-up interrupt is available by
using event counter mode of the timer A3 (TA3IN) that shares a pin with CAN0.
If P83 (CAN0IN/CAN1IN) is used as a CAN input port, the CAN0 and CAN1 wake-up interrupts are
________
available by using INT1 that shares a pin with CAN0IN/CAN1IN.
22.4.1.2 CAN1 Wake-Up Interrupt
When a signal applied to the CAN1WU pin is on the falling edge, the CAN1WUR bit in the IIO5IR
register is set to "1" (interrupt requested). At this time, the IR bit in the CAN5IC register is set to "1"
(interrupt requested) if the CAN1WUE bit in the IIO5IE register is set to "1" (interrupt enabled).
If P83 (CAN0IN/CAN1IN) is used as a CAN input port, the CAN0 and CAN1 wake-up interrupts are
________
available by using INT1 that shares a pin with CAN0IN/CAN1IN.
22.4.1.3 CAN2 Wake-Up Interrupt
When a signal applied to the CAN2WU pin is on the falling edge, the CAN2WUR bit in the IIO6IR
register is set to "1" (interrupt requested). At this time, the IR bit in the CAN8IC register is set to "1"
(interrupt requested) if the CAN2WUE bit in the IIO6IE register is set to "1" (interrupt enabled).
Rev. 1.10 Oct. 18, 2005 Page 340 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
22.4.2 CANij Interrupts
Figure 22.41 shows a block diagram of the CANij interrupts. The followings cause the CAN-associated
interrupt request to be generated.
- The CANi slot k (k=0 to 15) completes a transmission
- The CANi slot k completes a reception
- The CANi module detects a bus error
- The CANi module moves into an error-passive state
- The CANi module moves into a bus-off state
The INTSEL bit in the CiCTLR1 register determines how an interrupt request is generated. When the
INTSEL bit is set to "0", one of the above CANi interrupt request sources cause the CANij interrupts to
be generated by the OR circuit. When the INTSEL bit is set to "1", CANi transmission completed, CANi
reception completed and CANi errors (CANi bus error detection, CANi module into error-passive state
and CANi module into bus-off state) cause the CANij interrupt corresponding to each source to be
generated.
22.4.2.1 When the INTSEL Bit is Set to "0"
If the CAN-associated interrupt is generated by one of the interrupt request sources listed in 22.4.2
CANij Interrupts, the corresponding bit in the CiSISTR register (i=0 to 2) is set to "1" (interrupt requested) when the CANi slot k completes a transmission or a reception. The corresponding bit in the
CiEISTR register (i=0 to 2) is set to "1" (interrupt requested) when the CANi module detects a bus
error, moves into an error-passive state, or moves into a bus-off state.
The CANi interrupt request signal is set to "1" when the corresponding bit in the CiSISTR or CiEISTR
is set to "1" and the corresponding bit in the CiSIMKR or CiEIMKR is set to "1"
When the CAN0 interrupt request signal changes "0" to "1", all CAN0jR bits (j=0 to 2) in the IIO9IR to
IIO11IR registers are set to "1" (interrupt requested).
If at least one of the CAN0jE bits in the IIO9IE to IIO11IE registers is set to "1" (interrupt enabled), the
IR bits in the corresponding CAN0IC to CAN2IC registers are set to "1" (interrupt requested). The
CAN0 interrupt request signal remains set to "1" if another interrupt request causes a corresponding bit
in the C0SISTR or C0EISTR to be set to "1" and the corresponding bit in the C0SIMKR or C0EIMKR to
be set to "1" after the CAN0 interrupt request signal changes "0" to "1". The CAN0jR and IR bits also
remain unchanged.
When the CAN1 interrupt request signal changes "0" to "1", all three CAN1jR bits in the IIO0IR to
IIO1IR and IIO5IR registers are set to "1" (interrupt requested).
If at least one of the CAN1jE bits in the IIO0IE to IIO1IE and IIO5IE registers is set to "1", the IR bits in
the corresponding CAN3IC to CAN5IC registers are set to "1". The CAN1 interrupt request signal
remains set to "1" if another interrupt request causes the corresponding bit in the C1SISTR or
C1EISTR to be set to "1" and the corresponding bit in the C1SIMKR or C1EIMKR to be set to "1" after
the CAN1 interrupt request signal changes "0" to "1". The CAN1jR and IR bits also remain unchanged.
Rev. 1.10 Oct. 18, 2005 Page 341 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
When the CAN2 interrupt request signal changes "0" to "1", all three CAN2jR bits in the IIO2IR to
IIO3IR and IIO6IR registers are set to "1" (interrupt requested).
If at least one of the CAN2jE bits in the IIO2IE to IIO3IE and IIO6IE registers is set to "1", the IR bits in
the corresponding CAN6IC to CAN8IC registers are set to "1". The CAN2 interrupt request signal
remains set to "1" if another interrupt request causes the corresponding bit in the C2SISTR or
C2EISTR to be set to "1" and the corresponding bit in the C2SIMKR or C2EIMKR to be set to "1" after
the CAN2 interrupt request signal changes "0" to "1". The CAN2jR and IR bits also remain unchanged.
Bits in the CiSISTR or CiEISTR register and CANijR bits (i=0 to 2, j=0 to 2) in the IIO0IR to IIO1IR,
IIO5IR, IIO9IR to IIO11IR, IIO2IR to IIO3IR and IIO6IR registers are not set to "0" automatically, interrupt acknowledgment notwithstanding. Set these bits to "0" by program.
The CANi interrupts are acknowledged when the CANijR bit in the IIO0IR to IIO1IR, IIO5IR, IIO9IR to
IIO11IR, IIO2IR to IIO3IR or IIO6IR register and the corresponding bit in the CiSISTR or CiEISTR
register are set to "0". If these bits remain set to "1", all CAN-associated interrupt request sources
become invalid.
22.4.2.2 When the INTSEL Bit is Set to "1"
If the CAN-associated interrupt is generated by one of the interrupt request sources listed in 22.4.2
CANij Interrupts, the corresponding bit in the CiSISTR register (i=0 to 2) is set to "1" (interrupt requested) when the CANi slot k(k=0 to 15) completes a transmission or a reception. The corresponding
bit in the CiEISTR registe is set to "1" (interrupt requested) when the CANi module detects a bus error,
moves into an error-passive state, or moves into a bus-off state.
The CANi receive interrupt request signal is set to "1" if the corresponding bit in the CiSIMKR is set to
"1" and the corresponding bit in the CiSISTR register is set to "1" when the CANi module completes a
reception.
The CANi transmit interrupt request signal is set to "1" if the corresponding bit in the CiSIMKR is set to
"1" and the corresponding bit in the CiSISTR register is set to "1" when the CANi module completes a
transmission.
The CANi error interrupt request signal is set to "1" if corresponding bits in the CiEIMKR are set to "1"
and the corresponding bit in the CiEISTR register is set to "1" when the CANi module detects a bus
error, moves into an error-passive state, or moves into a bus-off state.
When the CANi receive interrupt request signal changes "0" to "1", the CAN00R bit in the IIO9IR
register, the CAN10R bit in the IIO0IR register and the CAN20R bit in the IIO2IR register are set to "1"
(interrupt requested). If the CAN00E in the IIO9IE register is set to "1" (interrupt enabled), the IR bit in
the CAN0IC register is set to "1" (interrupt requested). If the CAN10E bit in the IIO0IE register is set to
"1" (interrupt enabled), the IR bit in the CAN3IC register is set to "1" (interrupt requested). If the
CAN20E bit in the IIO2IE register is set to "1" (interrupt enabled), the IR bit in the CAN6IC register is
set to "1" (interrupt requested).
When the CANi transmit interrupt request signal changes "0" to "1", the CAN01R bit in the IIO10IR
register, the CAN11R bit in the IIO1IR register and the CAN21R bit in the IIO3IR register are set to "1"
(interrupt requested). If the CAN01E in the IIO10IE register is set to "1" (interrupt enabled), the IR bit
in the CAN1IC register is set to "1" (interrupt requested). If the CAN11E bit in the IIO1IE register is set
to "1" (interrupt enabled), the IR bit in the CAN4IC register is set to "1" (interrupt requested). If the
CAN21E bit in the IIO3IE register is set to "1" (interrupt enabled), the IR bit in the CAN7IC register is
set to "1" (interrupt requested).
Rev. 1.10 Oct. 18, 2005 Page 342 of 435
REJ09B0162-0110
22. CAN Module
M32C/88 Group (M32C/88T)
When the CANi error interrupt request signal changes "0" to "1", the CAN02R bit in the IIO11IR register, the CAN12R bit in the IIO5IR register and the CAN22R bit in the IIO6IR register are set to "1"
(interrupt requested). If the CAN02E in the IIO11IE register is set to "1" (interrupt enabled), the IR bit
in the CAN2IC register is set to "1" (interrupt requested). If the CAN12E bit in the IIO5IE register is set
to "1" (interrupt enabled), the IR bit in the CAN5IC register is set to "1" (interrupt requested). If the
CAN22E bit in the IIO6IE register is set to "1" (interrupt enabled), the IR bit in the CAN8IC register is
set to "1" (interrupt requested).
The CANi error interrupt request signal remains set to "1" if another interrupt request causes the
corresponding bit in the CiEIMKR register is set to "1" and the corresponding bit in the CiEISTR to be
set to "1" after the CANi interrupt request signal changes "0" to "1". The CAN02R, CAN12R, CAN22R
and IR bits also remain unchanged.
Bits in the CiSISTR or CiEISTR register and CANijR bits (i=0 to 2, j=0 to 2) in the IIO0IR to IIO1IR,
IIO5IR, IIO9IR to IIO11IR, IIO2IR to IIO3IR or IIO6IR registers are not set to "0" automatically, interrupt
acknowledgment notwithstanding. Set these bits to "0" by program.
The CANi receive interrupt and CANi transmit interrupt are acknowledged when the CAN00R bit in the
IIO9IR register, the CAN01R bit in the IIO10IR register, the CAN10R bit in the IIO0IR register, the
CAN11R bit in the IIO1IR register, the CAN20R bit in the IIO2IR register and the CAN21R bit in the
IIO3IR register are set to "0". Corresponding bits in the CiSISTR register can be set to either "0" or "1".
The CANi error interrupt is acknowledged when the CAN02R bit in the IIO11IR register, the CAN12R
bit in the IIO5IR register, the CAN22R bit in the IIO6IR register and corresponding bits in the CiEISTR
register are set to "0".
If these bits remain set to "1", all CAN- associated interrupt request sources become invalid.
CANi Slot 0
Received
CANi Slot 0
Transmitted
INTSEL bit
"1"
SIM0 bit
"0"
CANi Interrupt Request/
CANi Receive Interrupt
Request Signal
SIS0 bit
CANi Slot 15
Received
CANi Slot 15
Transmitted
INTSEL bit
"1"
SIM15 bit
"0"
CANi Interrupt Request/
CANi Transmit Interrupt
Request Signal
SIS15 bit
CANi Bus Error
Detection
CANi Module into
Error-passive State
CANi Module into
Bus-off State
BEIS bit
BEIM bit
EPIS bit
INTSEL bit
"1"
EPIM bit
"0"
BOIS bit
BOIM bit
Figure 22.41 CAN Interrupts
Rev. 1.10 Oct. 18, 2005 Page 343 of 435
REJ09B0162-0110
CANi Interrupt Request/
CANi Error Interrupt
Request Signal
i=0 to 2
22. CAN Module
M32C/88 Group (M32C/88T)
22.5 CAN0/CAN2 Combination Mode
In CAN0/CAN2 combination mode, CAN0 and CAN2 are combined for input/ output.
Signals output from CAN0 and CAN2 are combined and provided from the CAN02OUT pin. Signal applied
to the CAN02IN pin is applied to CAN0 and CAN2.
When using CAN0/CAN2 combination mode, refer to Table 22.2 CAN Pin Settings for pin settings.
Figure 22.42 shows a block diagram of CAN0/CAN2 combination mode.
off (default)
P60 CAN2OUT
CAN2OUT
PS0_0=1
PSL0_0=1
CAN2
IPSA_7=0
P61 CAN2IN
CAN2IN
IPSA_7=1
IPSA_7=1
off (default)
P76 CAN0OUT/CAN02OUT
CAN0OUT
CAN0
IPSA_7=0
PS1_6=1
PSL1_6=0
PSC_6=1
IPS_3=0
P77 CAN0IN/CAN02IN
CAN0IN
off (default)
IPS_3=1
PS2_2=1
PSL2_2=1
CAN0OUT : PSC2_2=0
CAN1OUT : PSC2_2=1
P82 CAN0OUT/CAN1OUT
P83 CAN0IN/CAN1IN
off (default)
P96 CAN1OUT
CAN1OUT
CAN1
PS3_6=1(1)
PSC3_6=1
IPSA_3=1
CAN1IN
P95 CAN1IN
IPSA_3=0
NOTE:
1. Set the PD9 and PS3 registers immediately after the PRC2 bit in the PRCR register is set to
"1"(write enabled). Do not generate an interrupt or a DMA transfer between the instruction to
set to the PRC2 bit to "1" and the instruction to set the PD9 and PS3 registers.
Figure 22.42 CAN0/CAN2 Combination Mode Block Diagram
Rev. 1.10 Oct. 18, 2005 Page 344 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
22. CAN Module
22.5.1 Notes for CAN0/CAN2 Combination Mode
It is important to note the following information to use CAN0/CAN2 combination mode:
22.5.1.1 Transmission
Do not transmit frames with the same ID from CAN0 and CAN2.
When transmitting frames with different IDs simultaneously from CAN0 and CAN2, they are arbitrated.
As a result, the frame with higher priority gains the right to transmit.
22.5.1.2 Reception
When CAN0 transmits, ACK for the transmitted frame is transmitted from CAN2 even if other nodes
are not connected to the CAN bus. The same applies to CAN2 transmission.
22.5.1.3 Interrupts
CAN0 and CAN2 have different completed transmission or reception interrupts.
When CAN0 completes a transmission or reception, the IR bits in the corresponding CAN0IC to
CAN2IC registers are set to "1" (interrupt requested). When CAN2 completes a transmission or reception, the IR bits in the corresponding CAN6IC to CAN8IC registers are set to "1" (interrupt requested).
Use the CAN0 wake-up interrupt when operating in CAN0/CAN2 combination mode.
22.5.1.4 Errors
The count value of the error counter and the error status may differ between CAN0 and CAN2 depending on where the error has been generated.
When using CAN0/CAN2 combination mode, an error frame longer than the length noted in the specification may be transmitted.
22.4.1.5 Configuration
Set CAN configuration to both CAN0 and CAN2. Set CAN baud rates and bit timings of both CAN 0
and CAN2 to the same values.
Rev. 1.10 Oct. 18, 2005 Page 345 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
23. Programmable I/O Ports
23. Programmable I/O Ports
87 programmable I/O ports from P0 to P10 (excluding P85) are available in the 100-pin package and 123
programmable I/O ports from P0 to P15 (excluding P85) are in the 144-pin package. The direction registers
determine each port status, input or output. The pull-up control registers determine whether the ports,
divided into groups of four ports, are pulled up or not. P85 is an input port and no pull-up for this port is
______
______
allowed. The P8_5 bit in the P8 register indicates an NMI input level since P85 shares pins with NMI.
Figures 23.1 to 23.4 show programmable I/O port configurations.
Each pin functions as the programmable I/O port or an I/O pin for internal peripheral functions.
To use pins as input or output pins for internal peripheral functions, refer to the explanations for each
fuction.
The registers associated with the programmable I/O ports are as follows.
23.1 Port Pi Direction Register (PDi Register, i=0 to 15)
Figure 23.5 shows the PDi register.
The PDi register selects input or output status of a programmable I/O port. Each bit in the PDi register
corresponds to a port.
No bit controlling P85 is provided in the direction registers.
23.2 Port Pi Register (Pi Register, i=0 to 15)
Figure 23.6 shows the Pi register.
The Pi register writes and reads data to communicate with external devices. The Pi register consists of a
port latch to hold output data and a circuit to read pin states. Each bit in the Pi register corresponds to a port.
23.3 Function Select Register Aj (PSj Register) (j=0 to 3, 5, 8, 9)
Figures 23.7 to 23.10 show the PSj registers.
The PSj register selects either I/O port or peripheral function output if an I/O port shares pins with a peripheral function output (excluding DA0 and DA1.)
When multiple peripheral function outputs are assigned to a pin, set the PSL0 to PSL3, PSC, PSC2, PSC3
and PSD1 registers to select which function is used.
Tables 23.2 to 23.9 list peripheral function output control settings for each pin.
23.4 Function Select Register B0 to B3 (PSL0 to PSL3 Registers)
Figures 23.11 and 23.12 show the PSL0 to PSL3 registers.
When multiple peripheral function outputs are assigned to a pin, the PSL0 to PSL3 registers select which
peripheral function output is used.
Refer to 23.10 Analog Input and Other Peripheral Function Input for the PSL3_6 to PSL3_3 bits in the
PSL3 register.
23.5 Function Select Register C, C2, C3 (PSC, PSC2, PSC3 Registers)
Figures 23.13 and 23.14 show the PSC, PSC2 and PSC3 registers.
When multiple peripheral function outputs are assigned to a pin, the PSC, PSC2 and PSC3 registers select
which peripheral function output is used.
Refer to 23.10 Analog Input and Other Peripheral Function Input for the PSC_7 bit in the PSC register.
Rev. 1.10 Oct. 18, 2005 Page 346 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
23. Programmable I/O Ports
23.6 Function Select Register D (PSD1 Register)
Figure 23.14 shows the PSD1 register.
When multiple peripheral function outputs are assigned to a pin, the PSD1 register selects which peripheral
function output is used.
23.7 Pull-up Control Register 0 to 4 (PUR0 to PUR4 Registers)
Figures 23.15 and 23.16 show the PUR0 to PUR4 registers.
The PUR0 to PUR4 registers select whether the ports, divided into groups of four ports, are pulled up or not.
Ports with bits in the PUR0 to PUR4 registers set to "1" (pull-up) and the direction registers set to "0" (input
mode) are pulled up.
23.8 Port Control Register (PCR Register)
Figure 23.17 shows the PCR register.
The PCR register selects either CMOS output or N-channel open drain output as the P1 output format. If
the PCR0 bit is set to "1", N-channel open drain output is selected because the P-channel in the CMOS port
is turned off. This is, however, not a perfect open drain. Therefore, the absolute maximum rating of the
input voltage is between -0.3V and VCC + 0.3V.
23.9 Input Function Select Register (IPS and IPSA Registers)
Figures 23.17 and 23.18 show the IPS and IPSA registers.
The IPS3, IPS1 and IPS0 bits in the IPS register and the IPSA_3 and IPSA_0 bits in the IPSA register select
which pin is assigned for the intelligent I/O or CAN input functions.
Refer to 23.10 Analog Input and Other Peripheral Function Input for the IPS2 bit.
23.10 Analog Input and Other Peripheral Function Input
The PSL3_6 to PSL3_3 bits in the PSL3 register, the PSC_7 bit in the PSC register and the IPS2 bit in the
IPS register each separate analog I/O ports from other peripheral functions. Setting the corresponding bit to
"1" (analog I/O) to use the analog I/O port (DA0, DA1, ANEX0, ANEX1, AN4 to AN7 or AN150 to AN157)
prevents an intermediate potential from being impressed to other peripheral functions. The impressed intermediate potential may cause increase in power consumption.
Set the corresponding bit to "0" (except analog I/O) when analog I/O is not used. All peripheral function
inputs except the analog I/O port are available when the corresponding bit is set to "0". These inputs are
indeterminate when the bit is set to "1". When the PSC_7 bit is set to "1", key input interrupt request remains
_____
_____
unchanged regardless of KI0 to KI3 pin input level change.
Rev. 1.10 Oct. 18, 2005 Page 347 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Programmable I/O Ports
Select Pull-up
Direction Register
Port Latch
Data Bus
A
Input to each
Peripheral Function
B
C
Analog Signal
Option
Port
(A)
Hysteresis
Circuit (B)
Peripheral Function
Input
P00 to P07
P20 to P27
P30 to P37
P40 to P47
P50 to P52
P54
P55
P56
P57
P83, P84
P86
P87
P100 to P103
P104 to P107
(Note 1)
P114
P144 to P146
P152 to P157
: Available
: Not Available
NOTE:
1. These ports are provided in the 144-pin package only.
Figure 23.1 Programmable I/O Ports (1)
Rev. 1.10 Oct. 18, 2005 Page 348 of 435
REJ09B0162-0110
Circuit (C)
Analog I/F
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Programmable I/O Ports with the Port Control Register
Select Pull-up
Direction Register
PCR Register
Port Latch
Data Bus
A
Input to each
Peripheral Function
Option
Port
B
Circuit (B)
Peripheral Function
Input
(A)
Hysteresis
P10 to P14
P15 to P17
: Available
: Not Available
Programmable I/O Ports with the Function Select Register
INV03
T Q
Write Signal to INV03
Value Written to INV03
D
R
RESET
NMI
INV05
INV02
Select Pull-up
PS1 and PS2
Registers
Direction Register
Output from each
Peripheral Function
Data Bus
Port Latch
Input to each
Peripheral Function
Ports: P72, P73, P74, P75, P80, P81
Figure 23.2 Programmable I/O Ports (2)
Rev. 1.10 Oct. 18, 2005 Page 349 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Programmable I/O ports with the Function Select Register
Select Pull-up
D
PS0 to PS9
Registers
Direction Register
Output from each
Peripheral Function
Data Bus
Port Latch
A
Input to each
Peripheral Function
B
C
Analog Signal
Option
Port
(A)
Hysteresis
Circuit (B)
Peripheral Function
Input
P53
P60 to P67
P70, P71
(1)
P76, P77
P82
P90 to P92
P93 to P96
P97
P110 to P113
P120 to P127
P130 to P137
(Note 2)
P140 to P143
P150
P151
: Available
: Not Available
NOTES:
1. P70 and P71 are ports for the N-channel open drain output.
2. These ports are provided in the 144-pin package only.
Figure 23.3 Programmable I/O Ports (3)
Rev. 1.10 Oct. 18, 2005 Page 350 of 435
REJ09B0162-0110
Circuit (C)
Analog I/F
Circuit (D)
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Input Port (P85)
Data Bus
NMI
Figure 23.4 Programmable I/O Ports (4)
Port Pi Direction Register
b7
b6
b5
b4
b3
b2
b1
(i=0 to 15) (2)
b0
Symbol
Address
After Reset
PD0 to PD3
03E216, 03E316, 03E616, 03E716
PD4 to PD7
03EA16, 03EB16, 03C216, 03C316
0016
0016
PD8
PD9 to PD10
PD11
PD12 to PD13
PD14
PD15
03C616(3)
03C716(1), 03CA16
03CB16(2, 3)
03CE, 03CF16(2)
03D216(2, 3)
03D316(2)
00X0 00002
0016
XXX0 00002
0016
X000 00002
0016
Bit
Symbol
Bit Name
Function
RW
PDi_0
Port Pi0 Direction
Bit
0: Input mode (Functions as input port)
1: Output mode (Functions as output port) RW
PDi_1
Port Pi1 Direction
Bit
0: Input mode (Functions as input port)
1: Output mode (Functions as output port)
RW
PDi_2
Port Pi2 Direction
Bit
0: Input mode (Functions as input port)
1: Output mode (Functions as output port)
RW
PDi_3
Port Pi3 Direction
Bit
0: Input mode (Functions as input port)
RW
1: Output mode (Functions as output port)
PDi_4
Port Pi4 Direction
Bit
0: Input mode (Functions as input port)
RW
1: Output mode (Functions as output port)
PDi_5
Port Pi5 Direction
Bit
0: Input mode (Functions as input port)
1: Output mode (Functions as output port) RW
PDi_6
Port Pi6 Direction
Bit
0: Input mode (Functions as input port)
RW
1: Output mode (Functions as output port)
PDi_7
Port Pi7 Direction
Bit
0: Input mode (Functions as input port)
1: Output mode (Functions as output port)
RW
NOTES:
1. Set the PD9 register immediately after the PRC2 bit in the PRCR register is set to "1" (write enabled).
Do not generate an interrupt or a DMA transfer between the instruction to set the PRC2 bit to "1" and the
instruction to set the PD9 register.
2. Set the PD11 to PD15 registers to "FF16" in the 100-pin package.
3. Nothing is assigned in the PD8_5 bit in the PD8 register, the PD11_7 to PD11_5 bits in the PD11
register (144-pin package only) and the P14_7 bit in the PD14 register (144-pin package only).
If write, set these bits to "0". When read, their contents are indeterminate.
Figure 23.5 PD0 to PD15 Registers
Rev. 1.10 Oct. 18, 2005 Page 351 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Port Pi Register (i=0 to 15)(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
P0 to P5
P6 to P10
P11 to P15
Bit
Symbol
Address
03E016, 03E116, 03E416, 03E516, 03E816, 03E916
03C016, 03C116(2), 03C416(3), 03C516, 03C816
03C916(4), 03CC16, 03CD16, 03D016(4), 03D116
After Reset
Indeterminate
Indeterminate
Indeterminate
Function
Bit Name
Pin levels can be read by reading
bits corresponding to programmable
ports in input mode.
Pin levels can be controlled by
writing to bits corresponding to
programmable ports in output mode.
RW
Pi_0
Port Pi0 Bit
Pi_1
Port Pi1 Bit
Pi_2
Port Pi2 Bit
Pi_3
Port Pi3 Bit
RW
Pi_4
Port Pi4 Bit
RW
Pi_5
Port Pi5 Bit
RW
Pi_6
Port Pi6 Bit
RW
Pi_7
Port Pi7 Bit
RW
0: "L" level
1: "H" level
RW
RW
RW
NOTES:
1. The P11 to P15 registers are provided in the 144-pin package only.
2. P70 and P71 are ports for the N-channel open drain output. The pins go into high-impedance states
when P70 and P71 output "H" signal.
3. The P8_5 bit is for read only.
4. Nothing is assigned in the P11_7 to P11_5 bits in the P11 register and the P14_7 bit in the P14
register. If write, set these bits to "0". When read, their contents are indeterminate.
Figure 23.6 P0 to P15 Registers
Rev. 1.10 Oct. 18, 2005 Page 352 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Function Select Register A0
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PS0
Bit
Symbol
Address
03B016
After Reset
0016
Bit Name
Function
RW
PS0_0
Port P60 Output
Function Select Bit
0: I/O port
1: Selected by the PSL0_0 bit
RW
PS0_1
Port P61 Output
Function Select Bit
0: I/O port
1: CLK0 output
RW
PS0_2
Port P62 Output
Function Select Bit
0: I/O port
1: Selected by the PSL0_2 bit
RW
PS0_3
Port P63 Output
Function Select Bit
0: I/O port
1: TXD0/SDA0 output
RW
PS0_4
Port P64 Output
Function Select Bit
0: I/O port
1: Selected by the PSL0_4 bit
RW
PS0_5
Port P65 Output
Function Select Bit
0: I/O port
1: CLK1 output
RW
PS0_6
Port P66 Output
Function Select Bit
0: I/O port
1: Selected by the PSL0_6 bit
RW
PS0_7
Port P67 Output
Function Select Bit
0: I/O port
1: TXD1/SDA1 output
RW
Function Select Register A1
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PS1
Address
03B116
After Reset
0016
Bit
Symbol
Bit Name
PS1_0
Port P70 Output
Function Select Bit
0: I/O port
1: Selected by the PSL1_0 bit
RW
PS1_1
Port P71 Output
Function Select Bit
0: I/O port
1: Selected by the PSL1_1 bit
RW
PS1_2
Port P72 Output
Function Select Bit
0: I/O port
1: Selected by the PSL1_2 bit
RW
PS1_3
Port P73 Output
Function Select Bit
0: I/O port
1: Selected by the PSL1_3 bit
RW
PS1_4
Port P74 Output
Function Select Bit
0: I/O port
1: Selected by the PSL1_4 bit
RW
PS1_5
Port P75 Output
Function Select Bit
0: I/O port
1: Selected by the PSL1_5 bit
RW
PS1_6
Port P76 Output
Function Select Bit
0: I/O port
1: Selected by the PSL1_6 bit
RW
PS1_7
Port P77 Output
Function Select Bit
0: I/O port
1: Selected by the PSL1_7 bit
RW
Figure 23.7 PS0 Register and PS1 Register
Rev. 1.10 Oct. 18, 2005 Page 353 of 435
REJ09B0162-0110
Function
RW
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Function Select Register A2
b7
b6
b5
0 0
b4
b3
b2
b1
b0
0 0
Symbol
Address
PS2
03B416
After Reset
00X0 00002
Bit
Symbol
Bit Name
PS2_0
Port P80 Output
Function Select Bit
0: I/O port
1: Selected by the PSL2_0 bit
RW
PS2_1
Port P81 Output
Function Select Bit
0: I/O port
1: Selected by the PSL2_1 bit
RW
PS2_2
Port P82 Output
Function Select Bit
0: I/O port
1: Selected by the PSL2_2 bit
RW
Reserved Bit
Set to "0"
RW
(b4 - b3)
Function
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
(b5)
Reserved Bit
(b7 - b6)
Set to "0"
RW
Function Select Register A3(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PS3
Bit
Symbol
Address
03B516
After Reset
0016
Bit Name
Function
RW
PS3_0
Port P90 Output
Function Select Bit
0: I/O port
1: CLK3 output
RW
PS3_1
Port P91 Output
Function Select Bit
0: I/O port
1: Selected by the PSL3_1 bit
RW
PS3_2
Port P92 Output
Function Select Bit
0: I/O port
1: Selected by the PSL3_2 bit
RW
PS3_3
Port P93 Output
Function Select Bit
0: I/O port
1: RTS3
RW
PS3_4
Port P94 Output
Function Select Bit
0: I/O port
1: RTS4
RW
PS3_5
Port P95 Output
Function Select Bit
0: I/O port
1: CLK4 output
RW
PS3_6
Port P96 Output
Function Select Bit
0: I/O port
1: Selected by the PSC3_6 bit
RW
PS3_7
Port P97 Output
Function Select Bit
0: I/O port
1: Selected by the PSL3_7 bit
RW
NOTE:
1. Set the PS3 register immediately after the PRC2 bit in the PRCR register is set to "1" (write enabled).
Do not generate an interrupt or a DMA transfer between the instruction to set the PRC2 bit to "1"
and the instruction to set the PS3 register.
Figure 23.8 PS2 Register and PS3 Register
Rev. 1.10 Oct. 18, 2005 Page 354 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Function Select Register A5(1)
b7
b6
b5
b4
b3
b2
b1
b0
0
Symbol
Address
PS5
03B916
Bit
Symbol
After Reset
XXX0 00002
Bit Name
Function
RW
PS5_0
Port P110 Output
Function Select Bit
0: I/O port
1: OUTC10/ ISTXD1/BE1OUT
RW
PS5_1
Port P111 Output
Function Select Bit
0: I/O port
1: OUTC11/ ISCLK1 output
RW
PS5_2
Port P112 Output
Function Select Bit
0: I/O port
1: OUTC12
RW
PS5_3
Port P113 Output
Function Select Bit
0: I/O port
1: OUTC13
RW
Reserved Bit
Set to "0"
RW
(b4)
Nothing is assigned. When write, set to "0".
(b7 - b5) When read, its content is indeterminate.
NOTE:
1. The PS5 register is provided in the 144-pin package only.
Function Select Register A8(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PS8
0 0 0
Address
03A016
After Reset
X000 00002
Bit
Symbol
Bit Name
PS8_0
Port P140 output
function select bit
0: I/O port
1: OUTC14
RW
PS8_1
Port P141 output
function select bit
0: I/O port
1: OUTC15
RW
PS8_2
Port P142 output
function select bit
0: I/O port
1: OUTC16
RW
PS8_3
Port P143 output
function select bit
0: I/O port
1: OUTC17
RW
Reserved bit
Set to "0"
RW
(b6 - b4)
(b7)
Function
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
NOTE:
1. The PS8 register is provided in the 144-pin package only.
Figure 23.9 PS5 Register and PS8 Register
Rev. 1.10 Oct. 18, 2005 Page 355 of 435
REJ09B0162-0110
RW
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Function Select Register A9(1)
b7
b6
b5
b4
b3
b2
0
0 0
0
0
0
b1
b0
Symbol
Address
PS9
03A116
After Reset
0016
Bit
Symbol
Bit Name
PS9_0
Port P150 Output
Function Select Bit
0: I/O port
1: ISTXD0
RW
PS9_1
Port P151 Output
Function Select Bit
0: I/O port
1: ISCLK0 output
RW
Reserved Bit
Set to "0"
RW
(b7 - b2)
Function
NOTE:
1. The PS9 register is provided in the 144-pin package only.
Figure 23.10 PS9 Register
Rev. 1.10 Oct. 18, 2005 Page 356 of 435
REJ09B0162-0110
RW
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Function Select Register B0
b7
b6
0
b5
b4
0
b3
b2
0
b1
b0
0
Symbol
PSL0
Address
03B216
After Reset
0016
Bit
Symbol
Bit Name
PSL0_0
Port P60 Output Peripheral
Function Select Bit
0: RTS0
1: CAN2OUT
RW
Reserved Bit
Set to "0"
RW
Port P62 Output Peripheral
Function Select Bit
0: SCL0 output
1: STXD0
RW
Reserved Bit
Set to "0"
RW
Port P64 Output Peripheral
Function Select Bit
0: RTS1
1: Do not set to this value
RW
Reserved Bit
Set to "0"
RW
Port P66 Output Peripheral
Function Select Bit
0: SCL1 output
1: STXD1
RW
Reserved Bit
Set to "0"
RW
(b1)
PSL0_2
Function
(b3)
PSL0_4
(b5)
PSL0_6
(b7)
RW
Function Select Register B1
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PSL1
Bit
Symbol
Address
03B316
Bit Name
After Reset
0016
Function
RW
PSL1_0
Port P70 Output Peripheral 0: Selected by the PSC_0 bit
Function Select Bit
1: TA0OUT output(1)
RW
PSL1_1
Port P71 Output Peripheral 0: Selected by the PSC_1 bit
1: STXD2(1)
Function Select Bit
RW
PSL1_2
Port P72 Output Peripheral 0: Selected by the PSC_2 bit
Function Select Bit
1: TA1OUT output(1)
RW
PSL1_3
Port P73 Output Peripheral 0: Selected by the PSC_3 bit
Function Select Bit
1: V(1)
RW
PSL1_4
Port P74 Output Peripheral 0: Selected by the PSC_4 bit
Function Select Bit
1: W(1)
RW
PSL1_5
Port P75 Output Peripheral 0: W
Function Select Bit
1: OUTC12
RW
PSL1_6
Port P76 Output Peripheral 0: Selected by the PSC_6 bit
Function Select Bit
1: TA3OUT output(1)
RW
PSL1_7
Port P77 Output Peripheral 0: ISCLK0 output
1: OUTC14
Function Select Bit
RW
NOTE:
1. When setting the PSL1_i (i = 0 to 4, 6) bit to "1", set the corresponding PSC_i bit in the PSC register
to "0".
Figure 23.11 PSL0 Register and PSL1 Register
Rev. 1.10 Oct. 18, 2005 Page 357 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Function Select Register B2
b7
b6
b5
0 0
b4
b3
0
0
b2
b1
b0
Symbol
PSL2
Address
03B616
Bit
Symbol
After Reset
00X0 00002
Bit Name
Function
RW
PSL2_0
Port P80 Output Peripheral 0: TA4OUT output
Function Select Bit
1: U
RW
PSL2_1
Port P81 Output Peripheral 0: U
Function Select Bit
1: Selected by the PSC2_1 bit
RW
PSL2_2
Port P82 Output Peripheral 0: Do not set to this value
Function Select Bit
1: Selected by the PSC2_2 bit
RW
Reserved Bit
RW
(b4 - b3)
Set to "0"
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
(b5)
Reserved Bit
(b7 - b6)
Set to "0"
RW
Function Select Register B3
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PSL3
0
Bit
Symbol
(b0)
Address
03B716
After Reset
0016
Bit Name
Reserved Bit
Function
Set to "0"
RW
RW
PSL3_1
Port P91 Output Peripheral 0: SCL3 output
Function Select Bit
1: STxD3
RW
PSL3_2
Port P92 Output Peripheral 0: TxD3/SDA3 output
Function Select Bit
1: Do not set to this value
RW
PSL3_3
Port P93 Output Peripheral 0: Except DA0
1: DA0(1)
Function Select Bit
RW
PSL3_4
Port P94 Output Peripheral 0: Except DA1
1: DA1(1)
Function Select Bit
RW
PSL3_5
Port P95 Output Peripheral 0: Except ANEX0
1: ANEX0(1)
Function Select Bit
RW
PSL3_6
Port P96 Output Peripheral 0: Except ANEX1
1: ANEX1(1)
Function Select Bit
RW
PSL3_7
Port P97 Output Peripheral 0: SCL4 output
Function Select Bit
1: STxD4
RW
NOTE:
1. Although DA0, DA1, ANEX0 and ANEX1 can be used when this bit is set to "0", power consumption
may increase.
Figure 23.12 PSL2 Register and PSL3 Register
Rev. 1.10 Oct. 18, 2005 Page 358 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Function Select Register C
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PSC
Bit
Symbol
Address
03AF16
After Reset
00X0 00002
Bit Name
Function
RW
PSC_0
Port P70 Output Peripheral 0: TxD2/SDA2 output
Function Select Bit
1: Selected by the PSD1_0 bit
RW
PSC_1
Port P71 Output Peripheral 0: SCL2 output
Function Select Bit
1: Selected by the PSD1_1 bit
RW
PSC_2
Port P72 Output Peripheral 0: CLK2 output
Function Select Bit
1: V
RW
PSC_3
Port P73 Output Peripheral 0: RTS2
Function Select Bit
1: OUTC10/ISTxD1/BE1OUT
RW
PSC_4
Port P74 Output Peripheral 0: TA2OUT output
Function Select Bit
1: OUTC11/ISCLK1
RW
(b5)
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
PSC_6
Port P76 Output Peripheral 0: Selected by the PSD1_6 bit
1: CAN0OUT
Function Select Bit
RW
PSC_7
Key Input Interrupt
Disabled Select Bit
RW
0: P104 to P107 or KI0 to KI3
1: AN4 to AN7(1)
NOTE:
1. Set the ILVL2 to ILVL0 bits in the the KUPIC register to "0002" (interrupt disabled) when changing
the PSC_7 bit setting.
Although AN4 to AN7 can be used when this bit is set to "0", power consumption may increase.
Function Select Register C2
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PSC2
Bit
Symbol
(b0)
Address
03AC16
After Reset
XXXX X00X2
Bit Name
Function
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
PSC2_1
Port P81 Output Peripheral 0: Do not set to this value
Function Select Bit
1: OUTC15
RW
PSC2_2
Port P82 Output Peripheral 0: CAN0OUT
Function Select Bit
1: CAN1OUT
RW
Nothing is assigned. When write, set to "0".
(b7 - b3) When read, its content is indeterminate.
Figure 23.13 PSC Register and PSC2 Register
Rev. 1.10 Oct. 18, 2005 Page 359 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Function Select Register C3
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PSC3
Bit
Symbol
Address
03AD16
Bit Name
After Reset
X0XX XXXX2
Function
RW
Nothing is assigned. When write, set to "0".
(b5 - b0) When read, its content is indeterminate.
PSC3_6
(b7)
Port P96 Output Peripheral 0: TxD4/SDA4 output
Function Select Bit
1: CAN1OUT
RW
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
Function Select Register D1
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PSD1
Bit
Symbol
Address
03A716
Bit Name
After Reset
X0XX XX002
Function
RW
PSD1_0
Port P70 Output Peripheral 0: Do not set to this value
Function Select Bit
1: OUTC16
RW
PSD1_1
Port P71 Output Peripheral 0: Do not set to this value
Function Select Bit
1: OUTC17
RW
Nothing is assigned. When write, set to "0".
(b5 - b2) When read, its content is indeterminate.
PSD1_6
(b7)
Port P76 Output Peripheral 0: ISTxD0
Function Select Bit
1: OUTC13
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
Figure 23.14 PSC3 Register and PSD1 Register
Rev. 1.10 Oct. 18, 2005 Page 360 of 435
REJ09B0162-0110
RW
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Pull-Up Control Register 0(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PUR0
Bit
Symbol
Address
03F016
After Reset
0016
Bit Name
Function
RW
PU00
P00 to P03 Pull-Up
PU01
P04 to P07 Pull-Up
PU02
P10 to P13 Pull-Up
Pull-up setting for corresponding port RW
0: Not pulled up
RW
1: Pulled up
RW
PU03
P14 to P17 Pull-Up
RW
PU04
P20 to P23 Pull-Up
RW
PU05
P24 to P27 Pull-Up
RW
PU06
P30 to P33 Pull-Up
RW
PU07
P34 to P37 Pull-Up
RW
Pull-Up Control Register 1(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PUR1
Address
03F116
Bit
Symbol
After Reset
XXXX 00002
Bit Name
Function
RW
PU10
P40 to P43 Pull-Up
PU11
P44 to P47 Pull-Up
PU12
P50 to P53 Pull-Up
Pull-up setting for corresponding port RW
0: Not pulled up
RW
1: Pulled up
RW
PU13
P54 to P57 Pull-Up
RW
(b7 - b4)
Nothing is assigned. When write, set to "0".
When read, its content is indeterminate.
Pull-Up Control Register 2
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
PUR2
03DA16
Bit
Symbol
After Reset
0016
Bit Name
Function
RW
Pull-up setting for corresponding port RW
0: Not pulled up
RW
1: Pulled up
RW
PU20
P60 to P63 Pull-Up
PU21
P64 to P67 Pull-Up
PU22
P72 to P73 Pull-Up(1)
PU23
P74 to P77 Pull-Up
RW
PU24
P80 to P83 Pull-Up
RW
PU25
P84 to P87 Pull-Up(2)
RW
PU26
P90 to P93 Pull-Up
RW
PU27
P94 to P97 Pull-Up
RW
NOTES:
1. P70 and P71 cannot be pulled up.
2. P85 cannot be pulled up.
Figure 23.15 PUR0 Register, PUR1 Register and PUR2 Register
Rev. 1.10 Oct. 18, 2005 Page 361 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
<144-Pin Package>
Pull-Up Control Register 3
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PUR3
Address
03DB16
Bit
Symbol
After Reset
0016
Bit Name
Function
Pull-up setting for corresponding port RW
0: Not pulled up
RW
1: Pulled up
RW
PU30
P100 to P103 Pull-Up
PU31
P104 to P107 Pull-Up
PU32
P110 to P113 Pull-Up
PU33
P114 Pull-Up
RW
PU34
P120 to P123 Pull-Up
RW
PU35
P124 to P127 Pull-Up
RW
PU36
P130 to P133 Pull-Up
RW
PU37
P134 to P137 Pull-Up
RW
<100-Pin Package>
Pull-Up Control Register 3
b7
b6
b5
b4
b3
b2
b1
b0
0 0 0 0 0 0
RW
Symbol
PUR3
Address
03DB16
Bit
Symbol
0016
Bit Name
PU30
P100 to P103 Pull-Up
PU31
P104 to P107 Pull-Up
(b7 - b2)
After Reset
Reserved Bit
Function
RW
Pull-up setting for corresponding port
RW
0: Not pulled up
1: Pulled up
RW
Set to "0"
RW
Pull-Up Control Register 4(1)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
PUR4
Bit
Symbol
Address
03DC16
Bit Name
After Reset
XXXX 00002
Function
RW
PU40
P140 to P143 Pull-Up
PU41
P144 to P146 Pull-Up
PU42
P150 to P153 Pull-Up
Pull-up setting for corresponding port RW
0: Not pulled up
RW
1: Pulled up
RW
PU43
P154 to P157 Pull-Up
RW
Nothing is assigned. When write, set to "0".
(b7 - b4) When read, its content is indeterminate.
NOTE:
1. Set the PUR4 register to "0016" in the 100-pin package.
Figure 23.16 PUR3 Register and PUR4 Register
Rev. 1.10 Oct. 18, 2005 Page 362 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Port Control Register
b7
b6
b5
b4
b3
b2
b1
0
0
b0
Symbol
PCR
Bit
Symbol
PCR0
Address
03FF16
After Reset
XXXX XXX02
Bit Name
Port P1 Control
Bit(1)
Reserved Bit
Function
0 : CMOS output
1 : N-channel open drain output(2)
RW
RW
RW
Set to "0"
(b2 - b1)
Nothing is assigned. When write, set to "0".
(b7 - b3) When read, its content is indeterminate.
NOTES:
1. When using port P1 as I/O ports, CMOS port or N-channel open drain output port can be selected.
2. This function is designed not to make port P1 a full open drain but to turn off the P channel in the
CMOS port.
Absolute maximum rating of the input voltage is between -0.3V and VCC + 0.3V.
Input Function Select Register
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
Address
017816
IPS
0 0 0 0
Bit
Symbol
After Reset
0016
Function
RW
Communication Unit 0
Input Pin Select Bit 0
Assigns each function of ISCLK0 and
ISRxD0 to the following ports.
0: P77, P80
1: P151, P152
RW
IPS1
Communication Unit 1
Input Pin Select Bit 1
Assigns each function of INPC10,
INPC11/ISCLK1, INPC12/ISRxD1/BE1IN,
INPC13, INPC14, INPC15, INPC16 and
RW
INPC17 to the following ports.
0: P73, P74, P75, P76, P77, P81, P70, P71
1: P110, P111, P112, P113, P140, P141,
P142, P143
IPS2
Port P15 Input Peripheral 0: Except AN15(1)
Function Select Bit
1: AN15
RW
IPS3
CAN0IN Function
Pin Select Bit
0: P77
1: P83
RW
Reserved Bit
Set to "0"
RW
IPS0
(b7 - b4)
Bit Name
NOTE:
1. Although AN150 to AN157 can be used when the IPS2 bit is set to "0", power consumption may
increase.
Figure 23.17 PCR Register and IPS Register
Rev. 1.10 Oct. 18, 2005 Page 363 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Input Function Select Register A
b7
b6
b5
0
0 0
b4
b3
b2
b1
0
0
b0
Symbol
IPSA
Address
017916
After Reset
0016
Bit
Symbol
Bit Name
IPSA_0
Intelligent I/O Two-Phase
Pulse Input Pin and Base
Timer Reset Pin Switch Bit
0: P80, P81 used as two-phase pulse
input pin, INT1 as base timer reset
RW
1: P76, P77 used as two-phase pulse
input pin, INT0 as base timer reset
Reserved Bit
Set to "0"
RW
CAN1IN Function
Pin Select Bit
0: P95
1: P83
RW
Reserved Bit
Set to "0"
RW
CAN0/CAN2
Combination Select Bit
0: Use CAN0,CAN2 separately
1: Use CAN0/CAN2 combination RW
(32 slots)
(b2 - b1)
IPSA_3
(b7 - b4)
IPSA_7
Figure 23.18 IPSA Register
Rev. 1.10 Oct. 18, 2005 Page 364 of 435
REJ09B0162-0110
Function
RW
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Table 23.1 Unassigned Pin Settings in Single-Chip Mode
Pin Name
Setting
P0 to P15
Enter input mode and connect each pin to VSS via a resistor (pull-down);
(1,2,3.4,6)
(excluding P85)
or enter output mode and leave the pins open
XOUT(5)
Leave pin open
_______
NMI(P85)
Connect pin to VCC via a resistor (pull-up)
AVCC
Connect pin to VCC
AVSS, VREF, BYTE
Connect pins to VSS
NOTES:
1. Ports P11 to P15 are provided in the 144-pin package only.
2. If the port enters output mode and is left open, it is in input mode before output mode is entered by
program after reset. While the port is in input mode, voltage level on the pins is indeterminate and
power consumption may increase.
Direction register settings may be changed by noise or failure caused by noise. Configure direction
register settings regulary to increase the reliability of the program.
3. Use the shortest possible wiring to connect the microcomputer pins to unassigned pins (within 2 cm).
4. Ports P70 and P71 must output low-level ("L") signals if they are in output mode. They are ports for the
N-channel open drain output.
5. When the external clock is applied to the XIN pin, set the pin as written above.
6. In the 100-pin package, set "FF16" in the following addresses, in addition to the above settings:
Addresses 0003CB16, 0003CE16, 0003CF16, 0003D216, 0003D316
Microcomputer
P0 to P15(1) (except for P85)
(Input mode)
·
·
·
(Input mode)
(Output mode)
··
·
Open
VCC
NMI(P85)
XOUT
Open
VCC
AVCC
BYTE
AVSS
VREF
VSS
In single-chip mode
NOTE:
1. Ports P11 to P15 are provided in the 144-pin package only.
Figure 23.19 Unassigned Pin Handling
Rev. 1.10 Oct. 18, 2005 Page 365 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Table 23.2 Port P6 Peripheral Function Output Control
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
PS0 Register
_________ _______
0: P60/CTS0/SS0
1: Selected by the PSL0 register
________________
0: P61/CLK0(input)/CAN2IN/CAN2WU
1: CLK0(output)
0: P62/RxD0/SCL0(input)
1: Selected by the PSL0 register
0: P63/SRxD0/SDA0(input)
1: TxD0/SDA0 (output)
_________ _______
0: P64/CTS1/SS1
1: Selected by the PSL0 register
0: P65/CLK1(input)
1: CLK1(output)
0: P66/RxD1/SCL1(input)
1: Selected by the PSL0 register
0: P67/SRxD1/SDA1(input)
1: TxD1/SDA1(output)
PSL0 Register
_________
0: RTS0
1: CAN2OUT
Set to "0"
0: SCL0(output)
1: STxD0
Set to "0"
________
0: RTS1
1: Do not set this value
Set to "0"
0: SCL1(output)
1: STxD1
Set to "0"
Table 23.3 Port P7 Peripheral Function Output Control
PS1 Register
Bit 0 0: P70/TA0OUT(input)/SRxD2
INPC16/SDA2 (input)
1: Selected by the PSL1 register
Bit 1 0: P71/TB5IN/TA0IN/RxD2/
INPC17/SCL2 (input)
1: Selected by the PSL1 register
PSL1 Register
PSC Register(1)
0: Selected by the PSC register 0: TxD2/SDA2(output)
1: TA0OUT(output)
1: Selected by the PSD1 register 1: OUTC16
0: Selected by the PSC register 0: SCL2(output)
0: Do not set to this value
1: STxD2
1: Selected by the PSD1 register 1: OUTC17
Bit 2 0: P72/TA1OUT(input)/
0: Selected by the PSC register 0: CLK2(output)
CLK2(input)
1: Selected by the PSL1 register 1: TA1OUT(output)
1: V
_________ ______
Bit 3 0: P73/TA1IN/CTS2/SS2/
INPC10
1: Selected by the PSL1 register
Bit 4 0: P74/INPC11/ISCLK1(input)/
TA2OUT(input)
1: Selected by the PSL1 register
PSD1 Register
0: Do not set to this value
Set to "0"
_________
0: Selected by the PSC register 0: RTS2
Set to "0"
__
1: V
1: OUTC10/ISTxD1/BE1OUT
0: Selected by the PSC register 0: TA2OUT(output)
Set to "0"
1: W
1: OUTC11/ISCLK1(output)
___
Bit 5 0: P75/TA2IN/INPC12/
0: W
ISRxD1/BE1IN
1: Selected by the PSL1 register 1: OUTC12
Bit 6 0: P76/INPC13/TA3OUT(input)
1: Selected by the PSL1 register
Bit 7 0: P77/TA3IN/CAN0IN/
ISCLK0(input)/INPC14
1: Selected by the PSL1 register
Set to "0"
Set to "0"
0: Selected by the PSC register 0: Selected by the PSD1 register 0: ISTxD0
1: TA3OUT(output)
1: CAN0OUT
1: OUTC13
_____
_____
0: ISCLK0(output)
0: P104 to P107 or KI0 to KI3 Set to "0"
1: OUTC14
1: AN4 to AN7
(No relation to P77)
NOTE:
1. When setting the PSL1_i bit (i=0 to 4, 6) to "1", set the corresponding PSC_i bit to "0".
Rev. 1.10 Oct. 18, 2005 Page 366 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
Table 23.4 Port P8 Peripheral Function Output Control
PS2 Register
0: P80/ISRxD0/TA4OUT(input)
1: Selected by the PSL2 register
Bit 1
0: P81/TA4IN/INPC15
1: Selected by the PSL2 register
________
Bit 2
0: P82/INT0
1: Selected by the PSL2 register
Bit 3 to 7 Set to "000002"
Bit 0
PSL2 Register
0: TA4OUT(output)
1: U
____
0: U
1: Selected by the PSC2 register
0: Do not set to this value
1: Selected by the PSC2 register
PSC2 Register
Set to "0"
0: Do not set to this value
1: OUTC15
0: CAN0OUT
1: CAN1OUT
Table 23.5 Port P9 Peripheral Function Output Control
PS3 Register
Bit 0 0: P90/TB0IN/CLK3(input)
1: CLK3(output)
Bit 1 0: P91/TB1IN/RxD3/SCL3(input)
1: Selected by the PSL3 register
Bit 2 0: P92/TB2IN/SRxD3/SDA3(input)
1: Selected by the PSL3 register
_______
_______
Bit 3 0: P9
3/TB3IN/CTS3/SS3/DA0(output)
________
1: RTS3
________ ______
Bit 4 0: P9
4/TB4IN/CTS4/SS4/DA1(output)
________
1: RTS4
Bit 5 0: ________________
P95/ANEX0/CLK4(input)/CAN1IN/
CAN1WU
1: CLK4(output)
Bit 6 0: P96/SRxD4/ANEX1/SDA4(input)
1: Selected by the PSC3 register
__________
Bit 7 0: P97/RxD4/ADTRG/SCL4(input)
1: Selected by the PSL3 register
PSL3 Register
Set to "0"
PSC3 Register
Set to "0"
0: SCL3(output)
1: STxD3
0: TxD3/SDA3(output)
1: Do not set to this value
0: Except DA0
1: DA0
0: Except DA1
1: DA1
0: Except ANEX0
Set to "0"
1: ANEX0
0: Except ANEX1
1: ANEX1
0: SCL4(output)
1: STxD4
Table 23.6 Port P10 Peripheral Function Output Control
PSC Register
_____
_____
Bit 7 0: P104 to P107 or KI0 to KI3
1: AN4 to AN7
Rev. 1.10 Oct. 18, 2005 Page 367 of 435
REJ09B0162-0110
Set to "0"
Set to "0"
Set to "0"
Set to "0"
0: TxD4/SDA4
1: CAN1OUT
Set to "0"
M32C/88 Group (M32C/88T)
Table 23.7 Port P11 Peripheral Function Output Control
PS5 Register
0: P110/INPC10
1: OUTC10/ISTxD1/BE1OUT
Bit 1
0: P111/INPC11/ISCLK1(input)
1: OUTC11/ISCLK1(output)
Bit 2
0: P112/INPC12/ISRxD1/BE1IN
1: OUTC12
Bit 3
0: P113/INPC13
1: OUTC13
Bit 4 to 7 Set to "00002"
Bit 0
Table 23.8 Port P14 Peripheral Function Output Control
PS8 Register
0: P140/INPC14
1: OUTC14
Bit 1
0: P141/INPC15
1: OUTC15
Bit 2
0: P142/INPC16
1: OUTC16
Bit 3
0: P143/INPC17
1: OUTC17
Bit 4 to 7 Set to "00002"
Bit 0
Table 23.9 Port P15 Peripheral Function Output Control
PS9 Register
0: P150/AN150
1: ISTxD0
Bit 1
0: P151/AN151/ISCLK0(input)
1: ISCLK0(output)
Bit 2 to 7 Set to "0000002"
Bit 0
Rev. 1.10 Oct. 18, 2005 Page 368 of 435
REJ09B0162-0110
23. Programmable I/O Ports
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24. Flash Memory Version
Aside from the built-in flash memory, the flash memory version microcomputer has the same functions as the
masked ROM version.
In the flash memory version, rewrite operation to the flash memory can be performed in three modes: CPU
rewrite mode, standard serial I/O mode and parallel I/O mode.
Table 24.1 lists specifications of the flash memory version. See Tables 1.1 and 1.2 for the items not listed in
Table 24.1.
Table 24.1 Flash Memory Version Specifications
Item
Specification
Flash Memory Operating Mode
3 modes (CPU rewrite, standard serial I/O, parallel I/O)
Erase Block
User ROM Area
See Figure 24.1
Boot ROM Area
1 block (4 Kbytes)(1)
Program Method
Per word (16 bytes), per byte (8 bits)(2)
Erase Method
All block erase, erase per block
Program and Erase Control Method
Software commands control programming and erasing on the flash memory
Protect Method
The lock bit protects each block in the flash memory
Number of Commands
8 commands
Program and Erase Endurance
100 times(3)
Data Retention
10 years
ROM Code Protection
Standard serial I/O mode and parallel I/O mode supported
NOTES:
1. The rewrite control program for standard serial I/O mode is stored in the boot ROM area before shipment. This space can be rewritten in parallel I/O mode only.
2. Programming per byte is available in parallel I/O mode only.
3. Program and erase endurance refers to the number of times a block erase can be performed. Every block
erase performed after writing data of one word or more counts as one program and erase operation.
Table 24.2 Flash Memory Rewrite Mode Overview
Flash Memory
Rewrite Mode
CPU Rewrite Mode
Standard Serial I/O Mode
Parallel I/O Mode
Function
Software command execution
by CPU rewrites the user ROM
area.
EW mode 0:
Rewritable in areas other
than flash memory
EW mode 1:
Rewritable in flash memory
A dedicated serial
programmer rewrites the user
ROM area.
Standard serial I/O mode 1:
Clock synchronous serial I/O
Standard serial I/O mode 2:
UART
Standard serial I/O mode 3:
CAN
A dedicated parallel
programmer rewrites the
boot ROM area and user
ROM area.
Rewritable
Space
User ROM area
User ROM area
User ROM area
Boot ROM area
Operating
Mode
Single-chip mode
Memory expansion mode
(EW mode 0)
Boot mode (EW mode 0)
Boot mode
Parallel I/O mode
Programmer
None
Serial programmer
Parallel programmer
Rev. 1.10 Oct. 18, 2005 Page 369 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.1 Memory Map
The flash memory includes the user ROM area and the boot ROM area. The user ROM area has space to
store the microcomputer operating programs in single-chip mode and a separate 4-kbyte space as the block
A. Figure 24.1 shows a block diagram of the flash memory.
The user ROM area is divided into several blocks, each of which can be protected (locked) from program or
erase. The user ROM area can be rewritten in CPU rewrite mode, standard serial I/O mode and parallel I/O
mode.
The boot ROM area is located at the same addresses as the user ROM area. It can only be rewritten in
parallel I/O mode. A program in the boot ROM area is executed after a hardware reset occurs while a highlevel ("H") signal is applied to the CNVSS and P50 pins and a low-level ("L") signal is applied to the P55 pin.
A program in the user ROM area is executed after a hardware reset occurs while an "L" signal is applied to
the CNVSS pin. Consequently, the boot ROM area cannot be read.
00F00016
00FFFF16
Block A :4 Kbytes (4)
F8000016
Block 12 : 64 Kbytes
F8FFFF16
F9000016
Block 11 : 64 Kbytes
F9FFFF16
FA000016
Block 10 : 64 Kbytes
FAFFFF16
FB000016
FF000016
Block 9 : 64 Kbytes
FBFFFF16
FC000016
Block 5 : 32 Kbytes
Block 8 : 64 Kbytes
FCFFFF16
FD000016
Block 7 : 64 Kbytes
FF7FFF16
FF800016
FDFFFF16
Block 4 : 8 Kbytes
FF9FFF16
FE000016
FFA00016
Block 6 : 64 Kbytes
Block 3 : 8 Kbytes
FFBFFF16
FEFFFF16
FFC00016
Block 2 : 8 Kbytes
FF000016
FFDFFF16
FFE00016
FFEFFF16
FFF00016
FFFFFF16
Block 0 to Block 5 (32+8+8+8
+4+4) Kbytes
FFFFFF16
Block 1 : 4 Kbytes
Block 0 : 4 Kbytes
FFF00016
FFFFFF16
User ROM area
NOTES:
1. The boot ROM area can be rewritten in parallel I/O mode only.
2. When specifying a block, use an even address in the block to be specified.
3. Shown here is a flash memory block diagram in single-chip mode.
4. The block A cannot be erased by the all erase unlocked block command. Use the block erase command to erase.
Figure 24.1 Flash Memory Block Diagram
Rev. 1.10 Oct. 18, 2005 Page 370 of 435
REJ09B0162-0110
4 Kbytes
Boot ROM area(1)
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.1.1 Boot Mode
The microcomputer enters boot mode when a hardware reset is performed while a high-level ("H") signal
is applied to the CNVSS and P50 pins and a low-level ("L") signal is applied to the P55 pin. A program in
the boot ROM area is executed.
In boot mode, the FMR05 bit in the FMR0 register selects access to either the boot ROM area or the user
ROM area.
In the factory setting, the rewrite control program for standard serial I/O mode is stored into the boot ROM
area.
The boot ROM area can be rewritten in parallel I/O mode only. If any rewrite control program using erasewrite mode 0 (EW mode 0) is written in the boot ROM area, the flash memory can be rewritten according
to the system implemented.
24.2 Functions to Prevent Rewriting of Flash Memory
The flash memory has the ROM code protect function for parallel I/O mode and the ID code verify function
for standard I/O mode to prevent the flash memory from reading or rewriting.
24.2.1 ROM Code Protect Function
The ROM code protect function prevents the flash memory from reading and rewriting in parallel I/O
mode.
Figure 24.2 shows the ROMCP register. The ROMCP register is located in the user ROM area.
The ROM code protect function is enabled when the ROMCP1 bit is set to "002", "012" or "102".
24.2.2 ID Code Verify Function
Use the ID code verify function in standard serial I/O mode. The ID code sent from the serial programmer
is compared with the ID code written in the flash memory for a match. If the ID codes do not match,
commands sent from the serial programmer are not accepted. However, if the four bytes of the reset
vector are "FFFFFFFF16", ID codes are not compared, allowing all commands to be accepted.
The ID codes are 7-byte data stored consecutively, starting with the first byte, into addresses
0FFFFDF16, 0FFFFE316, 0FFFFEB16, 0FFFFEF16, 0FFFFF316, 0FFFFF716 and 0FFFFFB16. The flash
memory must have a program with the ID codes set in these addresses.
Rev. 1.10 Oct. 18, 2005 Page 371 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
ROM Code Protect Control Address(5)
b7
b6
b5
b4
b3
b2
b1
b0
Symbol
ROMCP
1 1 1 1 1 1
Bit
Symbol
Address
FFFFFF16
Factory Setting
FF16(4)
Bit Name
Function
Reserved Bit
Set to "1"
RW
RW
(b5 - b0)
b7 b6
ROM Code Protect
ROMCP1
Level 1 Set Bit(1, 2, 3)
0 0: ROM code protection active
0 1: ROM code protection active
1 0: ROM code protection active
1 1: ROM code protection inactive
RW
NOTES:
1. When the ROM code protection is active by the ROMCP1 bit setting, the flash memory is protected
against reading or rewriting in parallel I/O mode.
2. Set the bit 5 to bit 0 to "1111112" when the ROMCP1 bit is set to a value other than "112".
If the bit 5 to bit 0 are set to values other than "1111112", the ROM code protection may not become
active by setting the ROMCP1 bit to a value other than "112".
3. To make the ROM code protection inactive, erase a block including the ROMCP address in standard
serial I/O mode or CPU rewrite mode.
4. The ROMCP address is set to "FF16" when a block, including the ROMCP address, is erased.
5. When a value of the ROMCP address is "0016" or "FF16", the ROM code protect function is disabled.
Figure 24.2 ROMCP Address
Address
FFFFDF16 to FFFFDC16
ID1
Undefined Instruction Vector
FFFFE316 to FFFFE016
ID2
Overflow Vector
FFFFE716 to FFFFE416
BRK Instruction Vector
FFFFEB16 to FFFFE816
ID3
Address Match Vector
FFFFEF16 to FFFFEC16
ID4
Single-Step Vector
FFFFF316 to FFFFF016
ID5
Watchdog Timer Vector
FFFFF716 to FFFFF416
ID6
DBC Vector
FFFFFB16 to FFFFF816
ID7
NMI Vector
FFFFFF16 to FFFFFC16
ROMCP Reset Vector
4 bytes
Figure 24.3 Address for ID Code Stored
Rev. 1.10 Oct. 18, 2005 Page 372 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3 CPU Rewrite Mode
In CPU rewrite mode, the user ROM area can be rewritten when the CPU executes software commands.
The user ROM area can be rewritten with the microcomputer mounted on a board without using a parallel
or serial programmer.
In CPU rewrite mode, only the user ROM area shown in Figure 24.1 can be rewritten. The boot ROM area
cannot be rewritten. The program and block erase commands are executed only for each block in the user
ROM area.
Erase-write (EW) mode 0 and erase-write mode 1 are provided as CPU rewrite mode. Table 24.3 lists
differences between EW mode 0 and EW mode 1.
Table 24.3 EW Mode 0 and EW Mode 1
Item
EW mode 0
EW mode 1
Operating Mode
• Single-chip mode
• Boot mode
Single-chip mode
Space where the rewrite control
program can be placed
• User ROM area
• Boot ROM area
User ROM area
Space where the rewrite control
program can be executed
The rewrite control program must be
The rewrite control program can be executed
transferred to any space other than the flash in the user ROM area
memory (e.g.,RAM) before being executed
Space which can be rewritten
User ROM area
User ROM area
However, this excludes blocks with the rewrite
control program
Software Command Restriction
None
• Program and block erase commands
cannot be executed in a block having the
rewrite control program.
• Erase all unlocked block command
cannot be executed when the lock bit
in a block having the rewrite control
program is set to "1"(unlocked) or
when the FMR02 bit in the FMR0
register is set to "1"(lock bit disabled).
• Read status register command cannot be used.
Mode after Programming or
Erasing
Read status register mode
Read array mode
CPU State during Auto Program
and Erase Operation
Operating
In a hold state (I/O ports maintains the state
before the command was executed)(1)
Flash Memory State Detection
• Read the FMR00, FMR06 and FMR07
bits in the FMR0 register by program
• Execute the read status register
command to read the SR7, SR5 and SR4
bits in the SRD register
Read the FMR00, FMR06 and FMR07 bits in
the FMR0 register by program
NOTE:
_______
1. Do not generate an interrupt (except NMI interrupt) or a DMA transfer.
24.3.1 EW Mode 0
The microcomputer enters CPU rewrite mode by setting the FMR01 bit in the FMR0 register to "1" (CPU
rewrite mode enabled) and is ready to accept commands. EW mode 0 is selected by setting the FMR11
bit in the FMR1 register to "0". To set the FMR01 bit to "1", set to "1" after first writing "0".
The software commands control programming and erasing. The FMR0 register or the SRD register indicates whether a program or erase operation is completed as expected or not.
24.3.2 EW Mode 1
EW mode 1 is selected by setting the FMR11 bit to "1" after the FMR01 bit is set to "1". (Both bits must
be set to "0" first before setting to "1".)
The FMR0 register indicates whether or not a program or erase operation has been completed as expected. The SRD register cannot be read in EW mode 1.
Rev. 1.10 Oct. 18, 2005 Page 373 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.3 Flash Memory Control Register (FMR0 Register and FMR1 Register)
Flash Memory Control Register 0
b7
b6
b5
b4
b3
b2
b1
b0
0
Symbol
FMR0
Bit
Symbol
Address
005716
After Reset
0000 00012
Bit Name
Function
RW
erasing)(6)
FMR00
RY/BY Status Flag
0: BUSY (programming or
1: READY
FMR01
CPU Rewrite Mode
Select Bit(1, 7)
0: Disables CPU rewrite mode
1: Enables CPU rewrite mode
RW
FMR02
Lock Bit Disable
Select Bit(2)
0: Enables lock bit
1: Disables lock bit
RW
FMSTP
Flash Memory Stop
Bit(3, 5)
0: Starts the flash memory
1: Stops the flash memory
(Enters low power consumption state
and flash memory is reset)
RO
RW
Reserved Bit
Set to "0"
RW
FMR05
User ROM Area Select
Bit(3) (Available in boot
mode only)
0: Boot ROM area is accessed
1: User ROM area is accessed
RW
FMR06
Program Status Flag(4)
0: Successfully completed
1: Terminated by error
RO
FMR07
Erase Status Flag(4)
0: Successfully completed
1: Terminated by error
RO
(b4)
NOTES:
1. Set the FMR01 bit while the NMI pin is held "H". Set it by program in a space other than the flash
memory in EW mode 0.
2. Set the FMR02 bit to "1" in 8-bit unit immediately after setting it first to "0" while the FMR01 bit is set to
"1". Do not generate an interrupt or a DMA transfer between setting the FMR02 bit to "0" and setting it
to "1".
3. Set the FMSTP and FMR05 bits by program in a space other than the flash memory.
4. The FMR07 and FMR06 bits is set to "0" by executing the clear status command.
5. FMSTP bit setting is enabled when the FMR01 bit is set to "1" (CPU rewrite mode enabled).
The FMSTP bit can be set to "1" when the FMR01 bit is set to "0", but the flash memory does not enter
low-power consumption state nor is reset.
6. Write and read operations by the lock bit program command and read lock bit status command are
included.
7. To change a FMR01 bit setting from "0" to "1", set the FMR01 bit to "1" immediately after setting it
first to "0" in 8-bit unit. Do not generate an interrupt or a DMA transfer between setting the FMR01 bit to
"0" and setting it to "1".
To change a FMR01 bit setting from "1" to "0", enter read array mode to write to addresses 005716
in 16-bit unit. Write "0016" into 8 high-order bits.
e. g., to change a FMR01 bit setting from "1" to "0";
Assembly language:
mov.w #0000h, 0057h
Figure 24.4 FMR0 Register
Rev. 1.10 Oct. 18, 2005 Page 374 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
Flash Memory Control Register 1
b7
0
b6
b5
b4
0
0
b3
b2
b1
b0
Symbol
FMR1
Bit
Symbol
(b0)
FMR11
(b3 - b2)
(b5 - b4)
FMR16
(b7)
Address
005516
After Reset
0000 01012
Bit Name
Reserved Bit
EW Mode Select Bit(1)
Reserved Bit
Function
When read,
its content is indeterminate
0: EW mode 0
1: EW mode 1
When read,
its content is indeterminate
RW
RO
RW
RO
Reserved Bit
Set to "0"
RW
Lock Bit Status Flag
0: Locked
1: Unlocked
RO
Reserved Bit
Set to "0"
RW
NOTE:
1. Set the FMR11 bit to "1" in 8-bit unit immediately after setting it first to "0" while the FMR01 bit is set to "1".
Do not generate an interrupt or a DMA transfer between setting the FMR11 bit to "0" and setting it to "1".
Set it while the NMI pin is held "H".
If the FMR01 bit is set to "0", the FMR01 bit and FMR11 bit are both set to "0".
Figure 24.5 FMR1 Register
24.3.3.1 FMR00 Bit
The FMR00 bit indicates the flash memory operating state. It is set to "0" while the program, block
erase, erase all unlocked block, lock bit program, or read lock bit status command is being executed;
otherwise, it is set to "1".
24.3.3.2 FMR01 Bit
The microcomputer can accept commands when the FMR01 bit is set to "1" (CPU rewrite mode). Set
the FMR05 bit to "1" (user ROM area access) as well if in boot mode.
24.3.3.3 FMR02 Bit
The lock bit is invalid by setting the FMR02 bit to "1" (lock bit disabled). (Refer to 24.3.6 Data Protect
Function.) The lock bit is valid by setting the FMR02 bit to "0" (lock bit enabled).
The FMR02 bit does not change the lock bit status but disables the lock bit function. If the block erase
or erase all unlocked block command is executed when the FMR02 bit is set to "1", the lock bit status
changes "0" (locked) to "1" (unlocked) after command execution is completed.
Rev. 1.10 Oct. 18, 2005 Page 375 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.3.4 FMSTP Bit
The FMSTP bit initializes the flash memory control circuits and minimizes power consumption in the
flash memory. Access to the flash memory is disabled when the FMSTP bit is set to "1". Set the
FMSTP bit by program in a space other than the flash memory.
Set the FMSTP bit to "1" if one of the followings occurs:
• A flash memory access error occurs while erasing or programming in EW mode 0 (FMR00 bit does
not switch back to "1" (ready)).
• Low-power consumption mode or on-chip low-power consumption mode is entered.
Use the following the procedure to change the FMSTP bit setting.
(1) Set the FMSTP bit to "1"
(2) Set tps (the wait time to stabilize flash memory circuit)
(3) Set the FMSTP bit to "0"
(4) Set tps (the wait time to stabilize flash memory circuit)
Figure 24.8 shows a flow chart illustrating how to start and stop the flash memory before and after
entering low power mode. Follow the procedure on this flow chart.
When entering stop or wait mode, the flash memory is automatically turned off. When exiting stop or
wait mode, the flash memory is turned back on. The FMR0 register does not need to be set.
24.3.3.5 FMR05 Bit
The FMR05 bit selects the boot ROM or user ROM area in boot mode. Set to "0" to access (read) the
boot ROM area or to "1" (user ROM access) to access (read, write or erase) the user ROM area.
24.3.3.6 FMR06 Bit
The FMR06 bit is a read-only bit indicating an auto program operation state. The FMR06 bit is set to "1"
when a program error occurs; otherwise, it is set to "0". Refer to 24.3.8 Full Status Check.
24.3.3.7 FMR07 Bit
The FM07 bit is a read-only bit indicating the auto erase operation state. The FMR07 bit is set to "1"
when an erase error occurs; otherwise, it is set to “0”. For details, refer to 24.3.8 Full Status Check.
Figure 24.6 shows how to enter and exit EW mode 0. Figure 24.7 shows how to enter and exit EW
mode 1.
24.3.3.8 FMR11 Bit
EW mode 0 is entered by setting the FMR11 bit to "0" (EW mode 0).
EW mode 1 is entered by setting the FMR11 bit to "1" (EW mode 1).
24.3.3.9 FMR16 Bit
The FMR16 bit is a read-only bit indicating the execution result of the read lock bit status command.
When the block, where the read lock bit status command is executed, is locked, the FMR16 bit is set to "0".
When the block, where the read lock bit status command is executed, is unlocked, the FMR16 bit is set to "1".
Rev. 1.10 Oct. 18, 2005 Page 376 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
Procedure to Enter EW Mode 0
Rewrite control program
Single-chip mode or boot mode
In boot mode only
Set the FMR05 bit to "1"(user ROM area accessed)
Set MCD and PM1 registers(1)
Set the FMR01 bit to "1" (CPU rewrite mode
enabled) after writing "0"(2)
Transfer the rewrite control program in CPU
rewrite mode to a space other than the flash
memory
Jump to the rewrite control program transferred to
a space other than the flash memory. (In the
following steps, use the rewrite control program in
a space other than the flash memory)
Execute the software commands
Execute the read array command(3)
Set the FMR01 bit to "0"
(CPU rewrite mode disabled)(5)
In boot mode only
Set the FMR05 bit to "0" (boot ROM area
accessed)(4)
Jump to a desired address in the flash memory
NOTES:
1. In CPU rewrite mode, set the MCD register to be the 10-MHz CPU clock frequency or less and set the PM12
bit in the PM1 register to "1" (internal access wait).
2. To set the FMR01 bit to "1", set it to "1" in 8-bit unit immediately after setting it first to "0". Do not generate an
interrupt or a DMA transfer between setting the bit to "0" and setting it to "1". Set the FMR01 bit in a space
other than flash memory. Set the FMR01 bit while the NMI pin is held "H".
3. Exit CPU rewrite mode after executing the read array command.
4. When the FMR05 bit is set to "1", the user ROM area can be accessed.
5. To change the FMR01 bit setting from "1" to "0", enter read array mode to write to addresses 005716 in 16-bit
unit. Write "0016" into 8 high-order bits.
Figure 24.6 How to Enter and Exit EW Mode 0
Rev. 1.10 Oct. 18, 2005 Page 377 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
Procedure to Enter EW Mode 1
Program in the ROM
Single-chip mode(1)
Set the MCD and PM1 registers(2)
Set the FMR01 bit to "1" (CPU rewrite mode
enabled) after writing "0"
Set the FMR11 bit to "1" (EW mode 1) after
writing "0"(3)
Execute the software commands
Set the FMR01 bit to "0"
(CPU rewrite mode disabled)(4)
NOTES:
1. In EW mode 1, do not enter boot mode.
2. In CPU rewrite mode, set the MCD register to be the 10-MHz CPU clock frequency or less. Set
the PM12 bit in the PM1 register to "1" (internal access wait).
3. To set the FMR01 bit to "1", set it to "1" in 8-bit unit immediately after setting it first to "0". Do not
generate an interrupt or a DMA transfer between setting the FMR01 bit to "0" and setting it to "1".
To set the FMR11 bit to "1", set it to "1" in 8-bit unit immediately after setting it first to "0". Do not
generate an interrupt or a DMA transfer between setting the FMR11 bit to "0" and setting it to "1".
Set the FMR01 and FMR11 bits while the NMI pin is held "H".
4. To change the FMR01 bit setting from "1" to "0", enter read array mode to write to addresses
005716 in 16-bit unit. Write "0016" into 8 high-order bits.
Figure 24.7 How to Enter and Exit EW Mode 1
Rev. 1.10 Oct. 18, 2005 Page 378 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
Low-power consumption
mode program
Transfer the low-power consumption mode program
to a space other than the flash memory
Set the FMR01 bit to "1" after setting it to "0"
(CPU rewrite mode enabled)(4)
Jump to the low-power consumption mode
program transferred to a space other than the
flash memory. (In the following steps, use the
low-power consumption mode program in a
space other than the flash memory.)
Set the FMSTP bit to "1" (The flash memory stops
operating. It is in a low-power consumption state)(1)
Switch clock source of the CPU clock.
The main clock stops.(2)
Process in low-power consumption mode or
on-chip oscillator low-power consumption mode
NOTES:
1. Set the FMSTP bit to "1" after the FMR01 bit is set to "1"
(CPU rewrite mode enabled).
2. Wait until clock stabilizes to switch a clock source of the
CPU clock to the main clock or sub clock.
3. Add tps ms wait time by program. Do not access the flash
memory during this wait time.
4. To set the FMR01 bit to "1", set it to "1" in 8-bit unit
immediately after setting it first to "0". Do not generate an
interrupt or a DMA transfer between setting the bit to "0"
and setting it to "1". Set the FMR01 bit while the NMI pin
is held "H".
5. To change the FMR01 bit setting from "1" to "0", enter
read array mode to write to addresses 005716 in 16-bit
unit. Write "0016" into 8 high-order bits.
Start main
clock
oscillation
Wait until
oscillation
stabilizes
Switch clock
source of the
CPU clock(2)
Set the FMSTP bit to "0" (flash memory operation)
Set the FMR01 bit to "0"
(CPU rewrite mode disabled)(5)
Wait until the flash memory stabilizes (tps ms)(3)
Jump to a desired address in the flash memory
Figure 24.8 Handling Before and After Low Power Consumption Mode
Rev. 1.10 Oct. 18, 2005 Page 379 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.4 Precautions in CPU Rewrite Mode
24.3.4.1 Operating Speed
Set the MCD4 to MCD0 bits in the MCD register to CPU clock frequency of 10 MHz or less before
entering CPU rewrite mode (EW mode 0 or EW mode 1). Also, set the PM12 bit in the PM1 register to
"1" (wait state).
24.3.4.2 Prohibited Instructions
The following instructions cannot be used in EW mode 0 because the CPU tries to read data in the flash
memory: the UND instruction, INTO instruction, JMPS instruction, JSRS instruction, and BRK instruction.
24.3.4.3 Interrupts (EW Mode 0)
• To use interrupts having vectors in a relocatable vector table, the vectors must be relocated to the
RAM area.
_______
• The NMI and watchdog timer interrupts are available since the FMR0 and FMR1 registers are forcibly reset when either interrupt occurs. Allocate the forward addresses for each interrupt routine to
_______
the fixed vector table. Flash memory rewrite operation is aborted when the NMI or watchdog timer
interrupt occurs. Execute the rewrite program again after exiting the interrupt routine.
• The address match interrupt is not available since the CPU tries to read data in the flash memory.
24.3.4.4 Interrupts (EW Mode 1)
• Do not acknowledge any interrupts with vectors in the relocatable vector table or address match
interrupt during the auto program or auto erase period.
• Do not use the watchdog timer interrupt.
_______
• The NMI interrupt is available since the FMR0 and FMR1 registers are forcibly reset when either
interrupt occurs. Allocate the forward address for the interrupt routine to the fixed vector table. Flash
_______
memory rewrite operation is aborted when the NMI interrupt occurs. Execute the rewrite program
again after exiting the interrupt routine.
24.3.4.5 How to Access
To set the FMR01, FMR02 in the FMR0 register or FMR11 bit in the FMR1 register to "1", set to "1"
in 8-bit units immediately after setting to "0". Do not generate an interrupt or a DMA transfer between
the instruction to set the bit to "0" and the instruction to set the bit to "1". Set the bit while a high-level
_______
("H") signal is applied to the NMI pin.
To change the FMR01 bit from "1" to "0", enter read array mode first, and write into address 005716 in
16-bit units. Eight high-order bits must be set to "0016".
24.3.4.6 Rewriting in the User ROM Area (EW Mode 0)
If the supply voltage drops while rewriting the block where the rewrite control program is stored, the
flash memory cannot be rewritten because the rewrite control program is not rewritten as expected. If
this error occurs, rewrite the user ROM area while in standard serial I/O mode or parallel I/O mode.
24.3.4.7 Rewriting in the User ROM Area (EW Mode 1)
Do not rewrite the block where the rewrite control program is stored.
24.3.4.8 DMA Transfer
In EW mode 1, do not generate a DMA transfer while the FMR00 bit in the FMR0 register is set to "0"
(busy-programming or erasing).
Rev. 1.10 Oct. 18, 2005 Page 380 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.2.4.9 Writing Command and Data
Write commands and data to even addresses in the user ROM area.
24.3.4.10 Wait Mode
When entering wait mode, set the FMR01 bit in the FMR0 register to "0" (CPU rewrite mode disabled)
before executing the WAIT instruction.
24.3.4.11 Stop Mode
When entering stop mode, the following settings are required:
• Set the FMR01 bit to "0" (CPU rewrite mode disabled). Disable a DMA transfer before setting the
CM10 bit to "1" (stop mode).
• Execute the instruction to set the CM10 bit to "1" (stop mode) and then the JMP.B instruction.
e.g.,
BSET
0, CM1
; Stop mode
JMP.B
L1
L1:
Program after exiting stop mode
24.3.4.12 Low-Power Consumption Mode and On-Chip Oscillator Low-Power Consumption Mode
If the CM05 bit is set to "1" (main clock stopped), do not execute the following commands:
• Program
• Block erase
• Erase all unlocked blocks
• Lock bit program
• Read lock bit status
Rev. 1.10 Oct. 18, 2005 Page 381 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.5 Software Commands
Read or write 16-bit commands and data from or to even addresses in the user ROM area, in 16-bit units.
When writing a command code, 8 high-order bits (D15 to D8) are ignored.
Table 24.4 Software Commands
First Bus Cycle
Command
Second Bus Cycle
Mode
Address
Data
(D15 to D0)
Mode
Address
Data
(D15 to D0)
Read Array
Write
X
xxFF16
Read Status Register
Write
X
xx7016
Read
X
SRD
Clear Status Register
Write
X
xx5016
Program
Write
WA
xx4016
Write
WA
WD
Block Erase
Write
X
xx2016
Write
BA
xxD016
Erase All Unlocked Block(1)
Write
X
xxA716
Write
X
xxD016
Lock Bit Program
Write
BA
xx7716
Write
BA
xxD016
Read Lock Bit Status
Write
X
xx7116
Write
BA
xxD016
NOTE:
1. Blocks 0 to 12 can be erased by the erase all unlocked block command.
Block A cannot be erased. The block erase command must be used to erase the block A.
SRD: Data in the SRD register (D7 to D0)
WA:
Address to be written (The address specified in the the first bus cycle is the same even address
as the address specified in the second bus cycle.)
WD:
16-bit write data
BA:
Highest-order block address (must be an even address)
X:
Any even address in the user ROM space
xx:
8 high-order bits of command code (ignored)
24.3.5.1 Read Array Command
The read array command reads the flash memory.
Read array mode is entered by writing command code "xxFF16" in the first bus cycle. Content of a
specified address can be read in 16-bit units after the next bus cycle.
The microcomputer remains in read array mode until another command is written. Therefore, contents
from multiple addresses can be read consecutively.
24.3.5.2 Read Status Register Command
The read status register command reads the SRD register (refer to 24.3.7 Status Register for detail).
By writing command code "xx7016" in the first bus cycle, the SRD register can be read in the second
bus cycle. Read an even address in the user ROM area.
Do not execute this command in EW mode 1.
24.3.5.3 Clear Status Register Command
The clear status register command clears the SRD register. By writing "xx5016" in the first bus cycle,
the FMR07 and FMR06 bits in the FMR0 register are set to "002" and the SR5 and SR4 bits in the SRD
register are set to "002".
Rev. 1.10 Oct. 18, 2005 Page 382 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.5.4 Program Command
The program command writes 1-word, or 2-byte, data to the flash memory.
Auto program operation (data program and verify) will start by writing command code "xx4016" in the
first bus cycle and data to the write address in the second bus cycle. The address value specified in
the first bus cycle must be the same even address as the write address specified in the second bus
cycle.
The FMR00 bit in the FMR0 register indicates whether or not an auto program operation has been
completed. The FMR00 bit is set to "0" (busy) during auto program and to "1" (ready) when the auto
program operation is completed.
After the completion of auto program operation, the FMR06 bit in the FMR0 register indicates whether
or not the auto program operation has been completed as expected. (Refer to 24.3.8 Full Status
Check.)
An address that is already written cannot be altered or rewritten.
Figure 24.9 shows a flow chart of the program command programming.
The lock bit can protect each block from being programmed inadvertently. (Refer to 24.3.6 Data Protect
Function.)
In EW mode 1, do not execute this command on the block where the rewrite control program is allocated.
In EW mode 0, the microcomputer enters read status register mode as soon as an auto program
operation starts. The SRD register can be read. The SR7 bit in the SRD register is set to "0" at the
same time an auto program operation starts. It is set to "1" when an auto program operation is
completed. The microcomputer remains in read status register mode until the read array command is
written. After completion of an auto program operation, the SRD register indicates whether or not the
auto program operation has been completed as expected.
Start
Write the command code "xx4016"
to an address to be written
Write data to an
address to be written
FMR00=1?
NO
YES
Full status check
Program operation
is completed
NOTE:
1. Write the command code and data to even addresses.
Figure 24.9 Program Command
Rev. 1.10 Oct. 18, 2005 Page 383 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.5.5 Block Erase Command
The block erase command erases each block.
Auto erase operation (erase and verify) will start in the specified block by writing command code
"xx2016" in the first bus cycle and "xxD016" to the highest-order even address of a block in the second
bus cycle.
The FMR00 bit in the FMR0 register indicates whether or not an auto erase operation has been
completed. The FMR00 bit is set to "0" (busy) during auto erase and to "1" (ready) when the auto
erase operation is completed.
After the completion of an auto erase operation, the FMR07 bit in the FMR0 register indicates whether
or not the auto erase operation has been completed as expected. (Refer to 24.3.8 Full Status
Check.)
Figure 24.10 shows a flow chart of the block erase command programming.
The lock bit can protect each block from being programmed inadvertently. (Refer to 24.3.6 Data
Protect Function.)
In EW mode 1, do not execute this command on the block where the rewrite control program is allocated.
In EW mode 0, the microcomputer enters read status register mode as soon as an auto erase operation starts. The SRD register can be read. The SR7 bit in the SRD register is set to "0" at the same
time an auto erase operation starts. It is set to "1" when an auto erase operation is completed. The
microcomputer remains in read status register mode until the read array command or read lock bit
status command is written.
Start
Write the command code "xx2016"
Write "xxD016" to the highestorder block address
FMR00=1?
NO
YES
Full status check
Block erase operation
is completed
NOTE:
1. Write the command code and data to even addresses.
Figure 24.10 Block Erase Command
Rev. 1.10 Oct. 18, 2005 Page 384 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.5.6 Erase All Unlocked Block Command
The erase all unlocked block command erases all blocks except the block A.
By writing command code "xxA716" in the first bus cycle and "xxD016" in the second bus cycle, auto
erase (erase and verify) operation will run continuously in all blocks except the block A.
The FMR00 bit in the FMR0 register indicates whether or not an auto erase operation has been
completed.
After the completion of an auto erase operation, the FMR07 bit in the FMR0 register indicates whether
or not the auto erase operation has been completed as expected.
The lock bit can protect each block from being programmed inadvertently. (Refer to 24.3.6 Data
Protect Function.)
In EW mode 1, do not execute this command when the lock bit for any block storing the rewrite control
program is set to "1" (unlocked) or when the FMR02 bit in the FMR0 register is set to "1" (lock bit
disabled).
In EW mode 0, the microcomputer enters read status register mode as soon as an auto erase operation starts. The SRD register can be read. The SR7 bit in the SRD register is set to "0" (busy) at the
same time an auto erase operation starts. It is set to "1" (ready) when an auto erase operation is
completed. The microcomputer remains in read status register mode until the read array command or
read lock bit status command is written.
Only blocks 0 to 12 can be erased by the erase all unlocked block command. The block A cannot be
erased. Use the block erase command to erase the block A.
Rev. 1.10 Oct. 18, 2005 Page 385 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.5.7 Lock Bit Program Command
The lock bit program command sets the lock bit for a specified block to "0" (locked).
By writing command code "xx7716" in the first bus cycle and "xxD016" to the highest-order even address of a block in the second bus cycle, the lock bit for the specified block is set to "0". The address
value specified in the first bus cycle must be the same highest-order even address of a block specified
in the second bus cycle.
Figure 24.11 shows a flow chart of the lock bit program command programming. Execute read lock bit
status command to read lock bit state (lock bit data).
The FMR00 bit in the FMR0 register indicates whether a lock bit program operation is completed.
Refer to 24.3.6 Data Protect Function for details on lock bit functions and how to set it to "1" (unlocked).
Start
Write the command code "xx7716" to
the highest-order block address
Write "xxD016" to the highest-order
block address
FMR00=1?
NO
YES
Full status check
Lock bit program operation
is completed
NOTE:
1. Write the command code and data to even addresses.
Figure 24.11 Lock Bit Program Command
Rev. 1.10 Oct. 18, 2005 Page 386 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.5.8 Read Lock Bit Status Command
The read lock bit status command reads the lock bit state (the lock bit data) of a specified block.
By writing command code "xx7116" in the first bus cycle and "xxD016" to the highest-order even address of a block in the second bus cycle, the FMR16 bit in the FMR1 register stores information on
whether or not the lock bit of a specified block is locked. Read the FMR16 bit after the FMR00 bit in the
FMR0 register is set to "1" (ready).
Figure 24.12 shows a flow chart of the read lock bit status command programming.
Start
Write the command code "xx7116"
Write "xxD016" to the highestorder block address
FMR00=1?
NO
YES
FMR16=0?
NO
YES
Block is locked
Block is not locked
NOTE:
1. Write the command code and data to even addresses.
Figure 24.12 Read Lock Bit Status Command
Rev. 1.10 Oct. 18, 2005 Page 387 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.6 Data Protect Function
Each block in the flash memory has a nonvolatile lock bit. The lock bit is enabled by setting the FMR02 bit
to "0" (lock bit enabled). The lock bit individually protects (locks) each block against program and erase.
This prevents data from being inadvertently written to or erased from the flash memory.
• When the lock bit status is set to "0", the block is locked (block is protected against program and erase).
• When the lock bit status is set to "1", the block is not locked (block can be programmed or erased).
The lock bit status is set to "0" (locked) by executing the lock bit program command and to "1" (unlocked)
by erasing the block. The lock bit status cannot be set to "1" by any commands.
The lock bit status can be read by the read lock bit status command.
The lock bit function is disabled by setting the FMR02 bit to "1". All blocks are unlocked. However,
individual lock bit status remains unchanged. The lock bit function is enabled by setting the FMR02 bit to
"0". Lock bit status is retained.
If the block erase or erase all unlocked block command is executed while the FMR02 bit is set to "1", the
target block or all blocks are erased regardless of lock bit status. The lock bit status of each block are set
to "1" after an erase operation is completed.
Refer to 24.3.5 Software Commands for details on each command.
24.3.7 Status Register (SRD Register)
The SRD register indicates the flash memory operating state and whether or not an erase or program
operation is completed as expected. The FMR00, FMR06 and FMR07 bits in the FMR0 register indicate
SRD register states.
Table 24.5 shows the SRD register.
In EW mode 0, the SRD register can be read when the followings occur.
• Any even address in the user ROM area is read after writing the read status register command
• Any even address in the user ROM area is read from when the program, block erase, erase all
unlocked block, or lock bit program command is executed until when the read array command is
executed.
24.3.7.1 Sequencer Status (SR7 and FMR00 Bits )
The sequencer status indicates the flash memory operating state. It is set to "0" while the program,
block erase, erase all unlocked block, lock bit program, or read lock bit status command is being
executed; otherwise, it is set to "1".
24.3.7.2 Erase Status (SR5 and FMR07 Bits)
Refer to 24.3.8 Full Status Check.
24.3.7.3 Program Status (SR4 and FMR06 Bits)
Refer to 24.3.8 Full Status Check.
Rev. 1.10 Oct. 18, 2005 Page 388 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
Table 24.5 Status Register
Bits in
Bits in
FMR0
Status
SRD
Register
Name
register
SR7 (D7)
Sequencer status
FMR00
SR6 (D6)
Reserved bit
(1)
SR5 (D5)
FMR07
SR4 (D4)
FMR06(1) Program status
Erase status
Definition
"0"
BUSY
"1"
READY
Value
after
Reset
1
-
-
Successfully completed
Error
0
Successfully completed
Error
0
-
SR3 (D3)
Reserved bit
-
-
-
SR2 (D2)
Reserved bit
-
-
-
SR1 (D1)
Reserved bit
-
-
-
SR0 (D0)
Reserved bit
-
-
-
D0 to D7: These data buses are read when the read status register command is executed.
NOTE:
1. The FMR07 (SR5) and FMR06 (SR4) bits are set to "0" by executing the clear status register command.
When the FMR07 (SR5) or FMR06 (SR4) bit is set to "1", the program, block erase, erase all unlocked
block and lock bit program commands are not accepted.
Rev. 1.10 Oct. 18, 2005 Page 389 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.3.8 Full Status Check
If an error occurs when a program or erase operation is completed, the FMR07 and FMR06 bits in the
FMR0 register are set to "1", indicating a specific error. Therefore, execution results can be confirmed by
verifying these bits (full status check).
Table 24.6 lists errors and FMR0 register state. Figure 24.13 shows a flow chart of the full status check
and handling procedure for each error.
Table 24.6 Errors and FMR0 Register State
FMR0 Register
(SRD Register)
State
FMR07
FMR06
(SR5)
(SR4)
1
1
1
0
0
1
Error
Error Occurrence Conditions
Command
• An incorrect command is written
sequence error • A value other than "xxD016" or "xxFF16" is written in the second
bus cycle of the lock bit program, block erase or erase all unlocked block command(1)
Erase error
• The block erase command is executed on a locked block(2)
• The block erase or erase all unlocked block command is executed on an unlock block, but the erase operation is not successfully completed
Program error • The program command is executed on locked blocks(2)
• The program command is executed on an unlocked block, but the
program operation is not completed as expected
• The lock bit program command is executed but the program operation is not successfully completed
NOTES:
1. The flash memory enters read array mode when command code "xxFF16" is written in the second bus
cycle of these commands. The command code written in the first bus cycle is ignored.
2. When the FMR02 bit is set to "1" (lock bit disabled), no error occurs even under the conditions above.
Rev. 1.10 Oct. 18, 2005 Page 390 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
Full status check
FMR06 =1
and
FMR07=1?
YES
Command
sequence error
(1) Execute the clear status register command and set the SR5 and SR4
bits to "0" (successfully completed) .
(2) Execute the correct commands again.
NO
FMR07=0?
NO
Erase error
YES
FMR06=0?
NO
Program error
YES
(1) Execute the clear status register command and set the SR5 bit to "0".
(2) Execute the lock bit read status command. Set the FMR02 bit to "1" (
lock bit disabled) if the lock bit in the block where the error occurred is
set to "0" (locked).
(3) Execute the block erase or erase all unlocked block command again.
NOTE: If similar error occurs, that block cannot be used.
If the lock bit is set to "1" (unlocked) in (2) above, that block
cannot be used.
[When a program operation is executed]
(1) Execute the clear status register command and set the SR4 bit to "0"(
successfully completed) .
(2) Execute the read lock bit status command and set the FMR02 bit to "1" if
the lock bit in the block where the error occurred is set to "0".
(3) Execute the program command again.
NOTE: If a similar error occurs, that block cannot be used.
If the lock bit is set to "1" in (2) above, that block cannot be used.
[When a lock bit program operation is executed]
(1) Execute the clear status register command and set the SR4 bit to "0".
(2) Set the FMR02 bit in the FMR0 register to "1".
(3) Execute the block erase command to erase the block where the error
occurred.
(4) Execute the lock bit program command again.
NOTE: If similar error occurs, that block cannot be used.
Full status check completed
NOTE: When either FMR06 or FMR07 bit is set to "1" (terminated by error) , the program, block erase, erase all unlocked block, lock bit
program and read lock bit status commands cannot be accepted.
Execute the clear status register command before each command.
Figure 24.13 Full Status Check and Handling Procedure for Each Error
Rev. 1.10 Oct. 18, 2005 Page 391 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.4 Standard Serial I/O Mode
In standard serial I/O mode, the serial programmer supporting the M32C/88 Group (M32C/88T) can be
used to rewrite the flash memory user ROM area, while the microcomputer is mounted on a board. For
more information about the serial programmer, contact your serial programmer manufacturer. Refer to the
user's manual included with your serial programmer for instructions.
Table 24.7 lists pin descriptions (flash memory standard serial I/O mode). Figures 24.14 to 24.16 show pin
connections in serial I/O mode.
24.4.1 ID Code Verify Function
The ID code verify function determines whether or not the ID codes sent from the serial programmer
matches those written in the flash memory. (Refer to 24.2 Functions to Prevent Rewriting of Flash
Memory.)
Rev. 1.10 Oct. 18, 2005 Page 392 of 435
REJ09B0162-0110
24. Flash Memory Version
M32C/88 Group (M32C/88T)
Table 24.7 Pin Description (Flash Memory Standard Serial I/O Mode)
Symbol
Function
I/O
Type
I
VCC
VSS
CNVSS
_______
RESET
Power supply
input
CNVSS
Reset input
XIN
XOUT
BYTE
AVCC
AVSS
VREF
I
O
I
I
P00 to P07
P10 to P17
P20 to P27
P30 to P37
P40 to P47
P50
P55
P51 to P54
P56, P57
P60 to P63
P64
Clock input
Clock output
BYTE input
Analog power
supply input
Reference
voltage input
Input port P0
Input port P1
Input port P2
Input port P3
Input port P4
___
CE input
_____
EPM input
Input port P5
Description
I
Apply the guaranteed program/erase supply voltage to the VCC pin.
Apply 0 V to the VSS pin
Connect this pin to VCC
Reset input pin. Apply 20 or more clock cycles to the XIN pin while "L" is
____________
applied to the RESET pin
Connect a ceramic resonator or crystal oscillator between XIN and XOUT
To use the external clock, input the clock from XIN and leave XOUT open
Connect this pin to VSS or VCC
Connect AVCC to VCC
Connect AVSS to VSS
Reference voltage input pin for the A/D converter
I
I
I
I
I
I
I
I
Apply "H" or "L" to this pin, or leave open
Apply "H" or "L" to this pin, or leave open
Apply "H" or "L" to this pin, or leave open
Apply "H" or "L" to this pin, or leave open
Apply "H" or "L" to this pin, or leave open
Apply "H" to this pin
Apply "L" to this pin
Apply "H" or "L" to this pin, or leave open
Input port P6
BUSY output
I
O
P65
SCLK input
I
P66
I
P70 to P75
P76
RxD
Data input
TxD
Data output
Input port P7
CAN output
P77
CAN input
I
P80 to P84
P86, P87
P85
P90 to P97
P100 to P107
P110 to P114
P120 to P127
P130 to P137
P140 to P146
P150 to P157
Input port P8
I
Apply "H" or "L" to this pin, or leave open
Standard serial I/O mode 1: BUSY signal output pin
Standard serial I/O mode 2: Program running verify monitor
Standard serial I/O mode 3: Leave open
Standard serial I/O mode 1: Serial clock input pin
Standard serial I/O mode 2, 3: Apply "L" to this pin
Standard serial I/O mode 1, 2: Serial data input pin
Standard serial I/O mode 3: Apply "H" to this pin
Standard serial I/O mode 1, 2: Serial data output pin
Standard serial I/O mode 3: Leave open
Apply "H" or "L" to this pin, or leave open
Standard serial I/O mode 1, 2: Apply "H" or "L" to this pin, or leave open
Standard serial I/O mode 3: CAN output pin
Standard serial I/O mode 1, 2: Apply "H" or "L" to this pin, or leave open
Standard serial I/O mode 3: CAN input pin
Apply "H" or "L" to this pin, or leave open
I
I
I
I
I
I
I
I
Connect this pin to VCC
Apply "H" or "L" to this pin, or leave open
Apply "H" or "L" to this pin, or leave open
Apply "H" or "L" to this pin, or leave open(1)
Apply "H" or "L" to this pin, or leave open(1)
Apply "H" or "L" to this pin, or leave open(1)
Apply "H" or "L" to this pin, or leave open(1)
Apply "H" or "L" to this pin, or leave open(1)
P67
I
I
O
I
O
____
NMI input
Input port P9
Input port P10
Input port P11
Input port P12
Input port P13
Input port P14
Input port P15
NOTE:
1. These pins are provided in the 144-pin package only.
Rev. 1.10 Oct. 18, 2005 Page 393 of 435
REJ09B0162-0110
24. Flash Memory Version
M32C/88 Group (M32C/88T)
EPM
RESET
CE
VCC
Mode settings
Signal
Value
CNVss
VCC
VSS
Vss >> VCC
VCC
75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
M32C/88 Group
(M32C/88T)
Flash Memory Version
100-Pin Package
100
CE
EPM
BUSY
SCLK
RXD
TXD
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
CANOUT
Connect to
oscillation
circuit
CANIN
RESET
CNVSS
VCC
VSS
Figure 24.14 Pin Connections in Standard Serial I/O Mode (1)
Rev. 1.10 Oct. 18, 2005 Page 394 of 435
REJ09B0162-0110
PLQP0100KB-A
(100P6Q-A)
24. Flash Memory Version
M32C/88 Group (M32C/88T)
Mode settings
VCC
Signal
Value
CNVss
Vcc
EPM
Vss
RESET
Vss >> Vcc
CE
Vcc
108 107 106 10 104 103 102 101 100
5
9 98 97 9 9 94 9
9
6 5
3
9
2
9
1
9
0
8
9
8
8
8
7
86 8 84
5
8
3
8
2
81 80 7 78 77 7
9
6
7 74 73
5
109
110
72
71
111
112
70
69
113
68
67
114
115
66
65
116
117
CE
64
118
119
63
62
120
121
61
60
122
123
59
58
M32C/88 Group
(M32C/88T)
Flash Memory Version
144-Pin Pacakge
124
125
126
127
128
129
130
131
132
57
56
55
54
EPM
53
52
51
50
49
133
134
48
47
135
46
45
136
137
44
43
138
139
BUSY
42
SCLK
140
141
41
40
RxD
142
143
39
38
TxD
144
37
1
2
3
4
5
6
7
8
9
1 11 1 13 14 15 16 17 18 1
0
2
9
2 21 22 23 24 2
0
5
2 27
6
2 29 3 31 3
8
0
2
3 34 3
3
5
3
6
VCC
VSS
CANIN
RESET
CNVSS
CANOUT
Connect to
oscillation
circuit
Figure 24.15 Pin Connections in Standard Serial I/O Mode (2)
Rev. 1.10 Oct. 18, 2005 Page 395 of 435
REJ09B0162-0110
PLQP0144KA-A
(144P6Q-A)
24. Flash Memory Version
M32C/88 Group (M32C/88T)
24.4.2 Circuit Application in Standard Serial I/O Mode
Figure 24.16 shows an example of a circuit application in standard serial I/O mode 1. Figure 24.17 shows
an example of a circuit application serial I/O mode 2. Figure 24.18 shows an example of a circuit application serial I/O mode 3. Refer to the user's manual of your serial programmer to handle pins controlled by
the serial programmer.
VCC
Microcomputer
VCC
SCLK
Clock input
P50(CE)
TXD
Data output
P55(EPM)
VCC
BUSY
BUSY output
RxD
Data input
CNVss
VCC
VCC
Reset input
RESET
User reset
signal
NMI
NOTES:
1. Control pins and external circuitry vary with the serial programmer. Refer to the user's manual
included with the serial programmer.
2. In this example, a selector controls the voltage applied to the CNVSS pin to switch between in
single-chip mode and in standard serial I/O mode.
3. In standard serial I/O mode 1, if the user reset signal becomes "L" while the microcomputer is
communicating with the serial programmer, break the connection between the user reset signal and
the RESET pin by, for example, a jumper selector.
Figure 24.16 Circuit Application in Standard Serial I/O Mode 1
Rev. 1.10 Oct. 18, 2005 Page 396 of 435
REJ09B0162-0110
24. Flash Memory Version
M32C/88 Group (M32C/88T)
Microcomputer
SCLK
Data Output
TxD
Monitor Output
BUSY
Data Input
RxD
VCC
P50(CE)
P55(EPM)
VCC
CNVss
VCC
NMI
NOTE:
1. In this example, a selector controls the voltage applied to the CNVSS pin to switch between
in single-chip mode and in standard serial I/O mode.
Figure 24.17 Circuit Application in Standard Serial I/O Mode 2
CAN Transceiver
CAN_H
CAN_L
CAN_H
CAN_L
VCC
Microcomputer
P77(CANIN)
P76(CANOUT)
P65(SCLK)
VCC
VCC
VCC
P66(RxD)
VCC
NMI
CNVss
P50(CE)
Reset Input
RESET
P55(EPM)
User Reset
Signal
NOTES:
1. Control pins and external circuitry vary with the serial programmer. Refer to the user's manual
included with the serial programmer.
2. In this example, a selector controls the voltage applied to the CNVSS pin to switch between in
single-chip mode and in standard serial I/O mode.
Figure 24.18 Circuit Application in Standard Serial I/O Mode 3
Rev. 1.10 Oct. 18, 2005 Page 397 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
24. Flash Memory Version
24.5 Parallel I/O Mode
In parallel I/O mode, the user ROM area and the boot ROM area can be rewritten by a parallel programmer
supporting the M32C/88 Group (M32C/88T). Contact your parallel programmer manufacturer for more
information on the parallel programmer. Refer to the user's manual included with your parallel programmer
for instructions.
24.5.1 Boot ROM Area
An erase block operation in the boot ROM area is applied to only one 4-Kbyte block. The rewrite control
program in standard serial I/O mode is written in the boot ROM area before shipment. Do not rewrite the
boot ROM area if using the serial programmer.
In parallel I/O mode, the boot ROM area is located in addresses FFF00016 to FFFFFF16. Rewrite this
address range only if rewriting the boot ROM area. (Do not access addresses other than addresses
FFF00016 to FFFFFF16.)
24.5.2 ROM Code Protect Function
The ROM code protect function prevents the flash memory from being read and rewritten in parallel I/O
mode. (Refer to 24.2 Functions to Prevent Rewriting of Flash Memory.)
Rev. 1.10 Oct. 18, 2005 Page 398 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
25. Electrical Characteristics (M32C/88T)
25. Electrical Characteristics
Table 25.1 Absolute Maximum Ratings
Symbol
Parameter
Condition
Value
Unit
VCC
Supply Voltage
VCC=AVCC
-0.3 to 6.0
V
AV CC
Analog Supply Voltage
VCC=AVCC
-0.3 to 6.0
V
VI
Input Voltage
-0.3 to VCC+0.3
V
VO
Output Voltage P00-P07, P10-P17, P20-P27, P30-P37, P40-P47,
P50-P57, P60-P67, P72-P77, P80-P84, P86, P87,
P90-P97, P100-P107, P110-P114, P120-P127,
P130-P137, P140-P146, P150-P157(1), XOUT
Pd
Power Dissipation
Topr
Operating
Ambient
Temperature
RESET, CNVSS, BYTE, P00-P07, P10-P17, P20P27, P30-P37, P40-P47, P50-P57, P60-P67, P72P77, P80-P87, P90-P97, P100-P107, P110-P114,
P120-P127, P130-P137, P140-P146, P150-P157(1),
VREF, XIN
P70, P71
-0.3 to 6.0
-0.3 to VCC+0.3
P70, P71
during CPU operation
-0.3 to 6.0
T version
Tstg
Storage Temperature
Rev. 1.10 Oct. 18, 2005 Page 399 of 435
REJ09B0162-0110
Topr=25° C
500
U version
400
T version
-40 to 85
U version
-40 to 105
during flash memory program and erase
operation
NOTE:
1. P11 to P15 are provided in the 144-pin package only.
V
mW
°C
0 to 60
-65 to 150
°C
25. Electrical Characteristics (M32C/88T)
M32C/88 Group (M32C/88T)
Table 25.2 Recommended Operating Conditions
(VCC=4.2 to 5.5V, VSS=0V at Topr = -40 to 85oC (T version)/-40 to 105oC (U version)
unless otherwise specified)
Symbol
Parameter
VCC
AVCC
Supply Voltage
Analog Supply Voltage
VSS
Supply Voltage
Standard
Min.
4.2
Typ.
5.0
VCC
Max.
5.5
0
AVSS
Analog Supply Voltage
VIH
Input High ("H")
Voltage
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57,
P60-P67, P72-P77, P80-P87(3), P90-P97, P100-P107, P110P114, P120-P127, P130-P137(4), P140-P146, P150-P157(4),
V
V
V
0
0.8VCC
Unit
V
VCC
V
XIN, RESET, CNVSS, BYTE
P70, P71
VIL
Input Low ("L")
Voltage
IOH(peak)
Peak Output
High ("H")
Current(2)
IOH(avg)
Average Output
High ("H")
Current(1)
IOL(peak)
IOL(avg)
0.8VCC
6.0
0
0.2VCC
V
-10.0
mA
-5.0
mA
10.0
mA
5.0
mA
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57,
P60-P67, P72-P77, P80-P87(3), P90-P97, P100-P107, P110P114, P120-P127, P130-P137(4), P140-P146, P150-P157(4),
XIN, RESET, CNVSS, BYTE
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60P67, P72-P77, P80-P84, P86, P87, P90-P97, P100-P107, P110-
P114, P120-P127, P130-P137, P140-P146, P150-P157(4)
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60P67, P72-P77, P80-P84, P86, P87, P90-P97, P100-P107, P110P114, P120-P127, P130-P137, P140-P146, P150-P157(4)
Peak Output Low P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60("L") Current(2)
P67, P70-P77, P80-P84, P86, P87, P90-P97, P100-P107, P110-
Average Output
Low ("L")
Current(1)
P114, P120-P127, P130-P137, P140-P146, P150-P157(4)
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60P67, P70-P77, P80-P84, P86, P87, P90-P97, P100-P107, P110P114, P120-P127, P130-P137, P140-P146, P150-P157(4)
NOTES:
1. Typical values when average output current is 100 ms.
2. Total IOL(peak) for P0, P1, P2, P86, P87, P9, P10, P11, P14 and P15 must be 80 mA or less.
Total IOL(peak) for P3, P4, P5, P6, P7, P80 to P84, P12 and P13 must be 80 mA or less.
Total IOH(peak) for P0, P1, P2, and P11 must be -40mA or less.
Total IOH(peak) for P86, P87, P9, P10, P14 and P15 must be -40 mA or less.
Total IOH(peak) for P3, P4, P5, P12 and P13 must be -40 mA or less.
Total IOH(peak) for P6, P7, and P80 to P84 must be -40 mA or less.
3. VIH and VIL reference for P87 applies when P87 is used as a programmable input port.
It does not apply when P87 is used as XCIN.
4. Ports P11 to P15 are provided in the 144-pin package only.
Rev. 1.10 Oct. 18, 2005 Page 400 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
25. Electrical Characteristics (M32C/88T)
Table 25.3 Recommended Operating Conditions (Continued)
(VCC=4.2 to 5.5V, VSS=0V at Topr = -40 to 85oC (T version)/-40 to 105oC (U version)
unless otherwise specified)
Symbol
Standard
Parameter
Min.
Typ.
Max.
Unit
f(BCLK)
CPU Operation Frequency
VCC=4.2 to 5.5 V
0
32
MHz
f(XIN)
Main Clock Input Frequency
VCC=4.2 to 5.5 V
0
24
MHz
f(XCIN)
Sub Clock Frequency
32.768
50
kHz
f(Ring)
On-chip Oscillator Frequency (VCC=5.0V, Topr=25° C)
0.5
1
2
MHz
f(PLL)
PLL Clock Frequency
VCC=4.2 to 5.5 V
10
32
MHz
tSU(PLL)
Wait Time to Stabilize PLL Frequency Synthesizer
VCC=5.0 V
5
ms
Rev. 1.10 Oct. 18, 2005 Page 401 of 435
REJ09B0162-0110
25. Electrical Characteristics (M32C/88T)
M32C/88 Group (M32C/88T)
VCC=5V
Table 25.4 Electrical Characteristics
(VCC=4.2 to 5.5V, VSS=0V at Topr = -40 to 85oC (T version)/-40 to 105oC (U version),
f(BCLK)=32MHz unless otherwise specified)
Symbol
VOH
Parameter
Output High ("H")
Voltage
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, IOH=-5 mA
P50-P57, P60-P67, P72-P77, P80-P84, P86,
P87, P90-P97, P100-P107, P110-P114, P120P127, P130-P137, P140-P146, P150-P157(1)
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, IOH=-200 µA
P50-P57, P60-P67, P72-P77, P80-P84, P86,
P87, P90-P97, P100-P107, P110-P114, P120P127, P130-P137, P140-P146, P150-P157(1)
XOUT
IOH=-1 mA
XCOUT
VOL
Output Low ("L")
Voltage
IIH
IIL
Input High ("H")
Current
Input Low ("L")
Current
RPULLUP Pull-up Resistance
Standard
Min.
Typ.
VCC-2.0
Max.
VCC
VCC-0.3
VCC
3.0
High Power
2.5
Low Power
No load applied
1.6
High Power
No load applied
0
Low Power
No load applied
0
HOLD, RDY, TA0IN-TA4IN, TB0IN-TB5IN,
INT0-INT5, ADTRG, CTS0-CTS4, CLK0-CLK4,
TA0OUT-TA4OUT, NMI, KI0-KI3, RxD0-RxD4,
SCL0-SCL4, SDA0-SDA4
RESET
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, VI=5 V
P50-P57, P60-P67, P70-P77, P80-P87, P90-P97,
P100-P107, P110-P114, P120-P127, P130P137, P140-P146, P150-P157(1), XIN, RESET,
CNVSS, BYTE
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, VI=0 V
P50-P57, P60-P67, P70-P77, P80-P87, P90-P97,
P100-P107, P110-P114, P120-P127, P130P137, P140-P146, P150-P157(1), XIN, RESET,
CNVSS, BYTE
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, VI=0 V
Unit
V
V
V
No load applied
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, IOL=5mA
P50-P57, P60-P67, P70-P77, P80-P84, P86,
P87, P90-P97, P100-P107, P110-P114, P120P127, P130-P137, P140-P146, P150-P157(1)
P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, IOL=200 µA
P50-P57, P60-P67, P70-P77, P80-P84, P86,
P87, P90-P97, P100-P107, P110-P114, P120P127, P130-P137, P140-P146, P150-P157(1)
XOUT
IOL=1 mA
XCOUT
VT+-VT- Hysteresis
Condition
V
2.0
V
0.45
V
2.0
V
V
0.2
1.0
V
0.2
1.8
5.0
V
µA
-5.0
µA
167
kΩ
30
50
P50-P57, P60-P67, P72-P77, P80-P84, P86,
P87, P90-P97, P100-P107, P110-P114, P120P127, P130-P137, P140-P146, P150-P157(1)
Feedback Resistance XIN
RfXIN
Feedback Resistance XCIN
RfXCIN
RAM Standby Voltage In stop mode
VRAM
NOTE:
1. Ports P11 to P15 are provided in the 144-pin package only.
Rev. 1.10 Oct. 18, 2005 Page 402 of 435
REJ09B0162-0110
1.5
10
2.0
MΩ
MΩ
V
25. Electrical Characteristics (M32C/88T)
M32C/88 Group (M32C/88T)
VCC=5V
Table 25.4 Electrical Characteristics (Continued)
(VCC=4.2 to 5.5V, VSS=0V at Topr = -40 to 85oC (T version)/-40 to 105oC (U version),
f(BCLK)=32MHz unless otherwise specified)
Symbol
I CC
Parameter
Measurement Condition
Power Supply Current In single-chip mode, output
pins are left open and other
pins are connected to VSS.
Standard
Min.
f(BCLK)=32 MHz, Square wave,
No division
f(BCLK)=32 kHz,
In low-power consumption mode,
Program running on ROM
f(BCLK)=32 kHz,
In low-power consumption mode,
Program running on RAM(1)
f(BCLK)=32 kHz, In wait mode,
Topr=25° C
While clock stops, Topr=25° C
While clock stops, Topr=85° C
While clock stops, Topr=105° C
While clock stops, Topr=125° C
NOTE:
1. Value is obtained when setting the FMSTP bit in the FMR0 register to "1" (flash memory stopped).
Rev. 1.10 Oct. 18, 2005 Page 403 of 435
REJ09B0162-0110
Typ.
28
Unit
Max.
50 mA
430
µA
25
µA
10
µA
0.8
5
50
100
200
µA
µA
µA
µA
25. Electrical Characteristics (M32C/88T)
M32C/88 Group (M32C/88T)
VCC=5V
Table 25.5 A/D Conversion Characteristics
(VCC=4.2 to 5.5V, VSS=0V at Topr = -40 to 85oC (T version)/-40 to 105oC (U version),
f(BCLK)=32MHz unless otherwise specified)
Symbol
Parameter
Standard
Measurement Condition
Min.
-
INL
Resolution
VREF=VCC
Integral Nonlinearity Error
DNL
VREF=VCC=5V
Unit
Typ. Max.
10
AN0 to AN7, AN00 to
AN07, AN20 to AN27,
AN150 to AN157,
ANEX0, ANEX1
±3
External op-amp
connection mode
±7
Bits
LSB
LSB
LSB
LSB
Differential Nonlinearity Error
±1
LSB
-
Offset Error
±3
LSB
-
Gain Error
±3
LSB
40
kΩ
RLADDER
Resistor Ladder
tCONV
10-bit Conversion Time(1, 2)
VREF=VCC
8
Time(1, 2)
2.06
µs
1.75
µs
0.188
µs
tCONV
8-bit Conversion
tSAMP
Sampling Time(1)
VREF
Reference Voltage
2
VCC
V
VIA
Analog Input Voltage
0
VREF
V
NOTES:
1. Divide f(XIN), if exceeding 16 MHz, to keep φAD frequency at 16 MHz or less.
2. With using the sample and hold function.
Table 25.6 D/A Conversion Characteristics
(VCC=4.2 to 5.5V, VSS=0V at Topr = -40 to 85oC (T version)/-40 to 105oC (U version),
f(BCLK)=32MHz unless otherwise specified)
Symbol
Parameter
Standard
Measurement Condition
Min.
tSU
-
Resolution
-
Absolute Accuracy
Typ.
Unit
Max.
Setup Time
RO
Output Resistance
IVREF
Reference Power Supply Input Current
4
10
(Note 1)
NOTE:
1. Measurement when using one D/A converter. The DAi register (i=0, 1) of the D/A converter, not being
used, is set to "0016". The resistor ladder in the A/D converter is excluded.
IVREF flows even if the VCUT bit in the AD0CON1 register is set to "0" (no VREF connection).
Rev. 1.10 Oct. 18, 2005 Page 404 of 435
REJ09B0162-0110
8
Bits
1.0
%
3
µs
20
kΩ
1.5
mA
25. Electrical Characteristics (M32C/88T)
M32C/88 Group (M32C/88T)
VCC=5V
Table 25.7 Flash Memory Version Electrical Characteristics
(VCC=4.5 to 5.5V at Topr= 0 to 60oC unless otherwise specified)
Symbol
Standard
Parameter
Min.
100
Typ.
Max.
Unit
-
Program and Erase Endurance(2)
-
Word Program Time (VCC=5.0V, Topr=25° C)
25
200
µs
-
Lock Bit Program Time
Block Erase Time
(VCC=5.0V, Topr=25° C)
25
0.3
0.3
0.5
0.8
µs
-
All-Unlocked-Block Erase Time(1)
Wait Time to Stabilize Flash Memory Circuit
Data Hold Time (Topr=-40 to 85 ° C)
200
4
4
4
4
4xn
15
tPS
4-Kbyte Block
8-Kbyte Block
32-Kbyte Block
64-Kbyte Block
cycles
s
s
s
s
s
µs
10
years
NOTES:
1. n denotes the number of block to be erased.
2. Number of program-erase cycles per block.
If Program and Erase Endurance is n cycle (n=100), each block can be erased and programmed n cycles.
For example, if a 4-Kbyte block A is erased after programming a word data 2,048 times, each to a different
address, this counts as one program and erase endurance. Data can not be programmed to the same address
more than once without erasing the block. (rewrite prohibited).
Table 25.8 Power Supply Timing
Symbol
Parameter
Standard
Measurement Condition
Min.
td(P-R)
Wait Time to Stabilize Internal Supply Voltage when
Power-on
td(P-R)
Recommanded
Operating Voltage
VCC
Wait Time to Stabilize Internal
Supply Voltage when Power-on
td(P-R)
CPU Clock
Figure 25.1 Power Supply Timing Diagram
Rev. 1.10 Oct. 18, 2005 Page 405 of 435
REJ09B0162-0110
VCC=4.2 to 5.5V
Typ.
Unit
Max.
2
ms
25. Electrical Characteristics (M32C/88T)
M32C/88 Group (M32C/88T)
VCC=5V
Timing Requirements
(VCC=4.2 to 5.5V, VSS=0V at Topr = -40 to 85oC (T version)/-40 to 105oC (U version) unless
otherwise specified)
Table 25.9 External Clock Input
Symbol
Parameter
Standard
Min.
Max.
Unit
tc
External Clock Input Cycle Time
31.25
ns
tw(H)
External Clock Input High ("H") Width
13.75
ns
tw(L)
External Clock Input Low ("L") Width
13.75
ns
tr
External Clock Rise Time
5
ns
tf
External Clock Fall Time
5
ns
Rev. 1.10 Oct. 18, 2005 Page 406 of 435
REJ09B0162-0110
25. Electrical Characteristics (M32C/88T)
M32C/88 Group (M32C/88T)
VCC=5V
Timing Requirements
(VCC=4.2 to 5.5V, VSS=0V at Topr = -40 to 85oC (T version)/-40 to 105oC (U version) unless
otherwise specified)
Table 25.10 Timer A Input (Count Source Input in Event Counter Mode)
Symbol
Standard
Parameter
Min.
Unit
Max.
tc(TA)
TAiIN Input Cycle Time
100
ns
tw(TAH)
TAiIN Input High ("H") Width
40
ns
tw(TAL)
TAiIN Input Low ("L") Width
40
ns
Table 25.11 Timer A Input (Gate Input in Timer Mode)
Standard
Symbol
Parameter
Min.
Max.
Unit
tc(TA)
TAiIN Input Cycle Time
400
ns
tw(TAH)
TAiIN Input High ("H") Width
200
ns
tw(TAL)
TAiIN Input Low ("L") Width
200
ns
Table 25.12 Timer A Input (External Trigger Input in One-Shot Timer Mode)
Standard
Symbol
Parameter
Unit
Min.
Max.
tc(TA)
TAiIN Input Cycle Time
200
ns
tw(TAH)
TAiIN Input High ("H") Width
100
ns
tw(TAL)
TAiIN Input Low ("L") Width
100
ns
Table 25.13 Timer A Input (External Trigger Input in Pulse Width Modulation Mode)
Standard
Symbol
Parameter
Unit
Min.
Max.
tw(TAH)
TAiIN Input High ("H") Width
100
ns
tw(TAL)
TAiIN Input Low ("L") Width
100
ns
Table 25.14 Timer A Input (Counter Increment/Decrement Input in Event Counter Mode)
Standard
Symbol
Parameter
Unit
Min.
Max.
tc(UP)
TAiOUT Input Cycle Time
2000
ns
tw(UPH)
TAiOUT Input High ("H") Width
1000
ns
tw(UPL)
TAiOUT Input Low ("L") Width
1000
ns
tsu(UP-TIN)
TAiOUT Input Setup Time
400
ns
th(TIN-UP)
TAiOUT Input Hold Time
400
ns
Rev. 1.10 Oct. 18, 2005 Page 407 of 435
REJ09B0162-0110
25. Electrical Characteristics (M32C/88T)
M32C/88 Group (M32C/88T)
VCC=5V
Timing Requirements
(VCC=4.2 to 5.5V, VSS=0V at Topr = -40 to 85oC (T version)/-40 to 105oC (U version) unless otherwise specified)
Table 25.15 Timer B Input (Count Source Input in Event Counter Mode)
Symbol
Parameter
Standard
Min.
Max.
Unit
tc(TB)
TBiIN Input Cycle Time (counted on one edge)
tw(TBH)
TBiIN Input High ("H") Width (counted on one edge)
40
ns
tw(TBL)
TBiIN Input Low ("L") Width (counted on one edge)
40
ns
100
ns
tc(TB)
TBiIN Input Cycle Time (counted on both edges)
200
ns
tw(TBH)
TBiIN Input High ("H") Width (counted on both edges)
80
ns
tw(TBL)
TBiIN Input Low ("L") Width (counted on both edges)
80
ns
Table 25.16 Timer B Input (Pulse Period Measurement Mode)
Symbol
Parameter
Standard
Min.
Max.
Unit
tc(TB)
TBiIN Input Cycle Time
400
ns
tw(TBH)
TBiIN Input High ("H") Width
200
ns
tw(TBL)
TBiIN Input Low ("L") Width
200
ns
Table 25.17 Timer B Input (Pulse Width Measurement Mode)
Standard
Symbol
Parameter
Unit
Min.
Max.
tc(TB)
TBiIN Input Cycle Time
400
ns
tw(TBH)
TBiIN Input High ("H") Width
200
ns
tw(TBL)
TBiIN Input Low ("L") Width
200
ns
Table 25.18 A/D Trigger Input
Symbol
Parameter
Standard
Min.
Max
Unit
tc(AD)
ADTRG Input Cycle Time (required for trigger)
1000
ns
tw(ADL)
ADTRG Input Low ("L") Pulse Width
125
ns
Table 25.19 Serial I/O
Symbol
Parameter
Standard
Min.
Max.
Unit
tc(CK)
CLKi Input Cycle Time
200
ns
tw(CKH)
CLKi Input High ("H") Width
100
ns
tw(CKL)
CLKi Input Low ("L") Width
100
td(C-Q)
TxDi Output Delay Time
ns
80
ns
th(C-Q)
TxDi Hold Time
0
ns
tsu(D-C)
RxDi Input Setup Time
30
ns
th(C-Q)
RxDi Input Hold Time
90
ns
_______
Table 25.20 External Interrupt INTi Input
Symbol
Parameter
Standard
Min.
Max.
Unit
tw(INH)
INTi Input High ("H") Width
250
ns
tw(INL)
INTi Input Low ("L") Width
250
ns
Rev. 1.10 Oct. 18, 2005 Page 408 of 435
REJ09B0162-0110
25. Electrical Characteristics (M32C/88T)
M32C/88 Group (M32C/88T)
VCC=5V
P0
P1
P2
P3
P4
P5
P6
P7
30pF
P8
P9
P10
P11
P12
P13
Note 1
P14
P15
NOTE:
1. Ports P11 to P15 are provided in the 144-pin package only.
Figure 25.2 P0 to P15 Measurement Circuit
Rev. 1.10 Oct. 18, 2005 Page 409 of 435
REJ09B0162-0110
25. Electrical Characteristics (M32C/88T)
M32C/88 Group (M32C/88T)
Vcc=5V
tc(TA)
tw(TAH)
TAiIN Input
tw(TAL)
tc(UP)
tw(UPH)
TAiOUT Input
tw(UPL)
TAiOUT Input
(Counter increment/
decrement input)
In event counter mode
TAiIN Input
th(TIN–UP)
tsu(UP–TIN)
(When counting on the falling edge)
TAiIN Input
(When counting on the rising edge)
tc(TB)
tw(TBH)
TBiIN Input
tw(TBL)
tc(AD)
tw(ADL)
ADTRG Input
tc(CK)
tw(CKH)
CLKi
tw(CKL)
th(C–Q)
TxDi
td(C–Q)
tsu(D–C)
th(C–D)
RxDi
tw(INL)
INTi Input
tw(INH)
NMI Input
2 CPU clock cycles +
300ns or more
("L" width)
Figure 25.3 VCC=5V Timing Diagram
Rev. 1.10 Oct. 18, 2005 Page 410 of 435
REJ09B0162-0110
2 CPU clock cycles +
300ns or more
26. Precautions (Special Function Registers(SFRs))
M32C/88 Group (M32C/88T)
26. Precautions
26.1 Special Function Registers (SFRs)
26.1.1 100-Pin Package
Set address spaces 03CB16, 03CE16, 03CF16, 03D216, 03D316 to "FF16" after reset when using the 100pin package. Address space 03DC16 must be set to "0016" after reset.
26.1.2 Register Settings
Table 26.2 lists registers containing bits which can only be written to. Set these registers with immediate
values. When establishing the next value by altering the present value, write the present value to the
RAM as well as to the register. Transfer the next value to the register after making changes in the RAM.
Table 26.1 Registers with Write-only Bits
Register
Address
Register
Address
WDTS Register
000E16
U3BRG Register
032916
G0RI Register
00EC16
U3TB Register
032B16, 032A16
G1RI Register
012C16
U2BRG Register
033916
U1BRG Register
02E916
U2TB Register
033B16, 033A16
U1TB Register
02EB16, 02EA16
UDF Register
034416
U4BRG Register
02F916
TA0 Register(1)
034716, 034616
TA1
Register(1)
034916, 034816
Register(1)
034B16, 034A16
U4TB Register
02FB16, 02FA16
TA11 Register
030316, 030216
TA2
TA21 Register
030516, 030416
TA3 Register(1)
034D16, 034C16
TA41 Register
030716, 030616
TA4 Register(1)
034F16, 034E16
DTT Register
030C16
U0BRG Register
036916
ICTB2 Register
030D16
U0TB Register
036B16, 36A16
NOTE:
1. In one-shot timer mode and pulse width modulation mode only.
Rev. 1.10 Oct. 18, 2005 Page 411 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Clock Generation Circuit)
26.2 Clock Generation Circuit
26.2.1 CPU Clock
• When the CPU operating frequency is 24 MHz or more, use the following procedure for better EMC
(Electromagnetic Compatibility) performance.
1) Oscillator connected between the XIN and XOUT pins, or external clock applied to the
XIN pin, has less than 24 MHz frequency.
2) Use the PLL frequency synthesizer to multiply the main clock.
• The main clock frequency must be 24 MHz or less.
26.2.2 Sub Clock
Set the CM03 bit to "0" (XCIN-XCOUT drive capacity "LOW") when selecting the sub clock (XCIN-XCOUT) as
the CPU clock, or Timer A or Timer B count source (fC32).
26.2.2.1 Sub Clock Oscillation
When oscillating the sub clock, set the CM04 bit in the CM0 register to "1" (XCIN-XCOUT oscillation
function) after setting the CM07 bit in the CM0 register to "0" (clock other than sub clock) and the
CM03 bit to "1" (XCIN-XCOUT drive capacity "HIGH"). Set the CM03 bit to "0" after sub clock oscillation
stabilizes.
Set the sub clock as the CPU clock, or Timer A or Timer B count source (fC32) after the above settings
are completed.
26.2.2.2 Using Stop Mode
When the microcomputer enters stop mode, the CM03 bit is automatically set to "1" (XCIN-XCOUT drive
capacity "HIGH"). Use the following procedure to select the main clock as the CPU clock when entering stop mode.
1) Set the CM17 bit in the CM1 register to "0" (main clock).
2) Set the CM21 bit in the CM2 register to "0" (clock selected by the CM17 bit).
3) Set the CM07 bit in the CM0 register to "0" (clock selected by the CM21 bit divided by the MCD
register setting).
After exiting stop mode, wait for the sub clock oscillation to stabilize. Then set the CM03 bit to "0" and
the CM07 bit to "1" (sub clock).
26.2.2.3 Oscillation Parameter Matching
If the sub slock oscillation parameters have only been evaluated with the drive capacity "HIGH", the
parameters should be reevaluated for drive capacity "LOW".
Contact your oscillator manufacturer for details on matching parameters.
Rev. 1.10 Oct. 18, 2005 Page 412 of 435
REJ09B0162-0110
26. Precautions (Clock Generation Circuit)
M32C/88 Group (M32C/88T)
26.2.3 PLL Frequency Synthesizer
Stabilize supply voltage to meet the power supply standard when using the PLL frequency synthesizer.
Table 26.2 Power Supply Ripple
Symbol
Standard
Parameter
Min.
Unit
Typ. Max.
f(ripple)
Power Supply Ripple Tolerable Frequency (VCC)
VCC=5V
10
kHz
VP-P(ripple)
Power Supply Ripple Voltage Fluctuation Range
VCC=5V
0.5
V
VCC(|
Power Supply Ripple Voltage Fluctuation Rate
VCC=5V
1
V/ms
V/ T|)
f(ripple)
f(ripple)
Power Supply Ripple Tolerable Frequency
(VCC)
Vp-p(ripple)
Power Supply Ripple Amplitude
Voltage
VCC
Vp-p(ripple)
Figure 26.1 Power Supply Fluctuation Timing
26.2.4 External Clock
Do not stop an external clock running if the main clock is selected as the CPU clock while the external
clock is applied to the XIN pin.
Do not set the CM05 bit in the CM0 register to "1" (main clock stopped) while the external clock input is
used for the CPU clock.
26.2.5 Clock Divide Ratio
Set the PM12 bit in the PM1 register to "0" (no wait state) when changing the MCD4 to MCD0 bit settings
in the MCD register.
26.2.6 Power Consumption Control
Stabilize the main clock, sub clock or PLL clock to switch the CPU clock source to each clock.
26.2.6.1 Wait Mode
When entering wait mode while the CM02 bit in the CM0 register is set to "1" (peripheral function stop
in wait mode), set the MCD4 to MCD0 bits in the MCD register to maintain the 10-MHz CPU clock
frequency or less.
When entering wait mode, the instruction queue reads ahead to instructions following the WAIT instruction, and the program stops. Write at least 4 NOP instructions after the WAIT instruction.
Rev. 1.10 Oct. 18, 2005 Page 413 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Clock Generation Circuit)
26.2.6.2 Stop Mode
• Use the following procedure to select the main clock as the CPU clock when entering stop mode.
1) Set the CM17 bit in the CM1 register to "0" (main clock).
2) Set the CM21 bit in the CM2 register to "0" (clock selected by the CM17 bit).
3) Set the CM07 bit in the CM0 register to "0" (clock selected by the CM21 bit divided by the MCD
register setting).
If the PLL clock is selected as the CPU clock source, set the CM17 bit to "0" (main clock) and the
PLC07 bit in the PLC0 register to "0" (PLL off) before entering stop mode.
______
• The microcomputer cannot enter stop mode if a low-level signal ("L") is applied to the NMI pin.
Apply a high-level ("H") signal instead.
____________
• If stop mode is exited by any reset, apply an "L" signal to the RESET pin until a main clock oscillation is stabilized enough.
______
• If using the NMI interrupt to exit stop mode, use the following procedure to set the CM10 bit in the
CM1 register (all clocks stopped).
______
1) Exit stop mode with using the NMI interrupt.
2) Generate a dummy interrupt.
3) Set the CM10 bit to "1".
e.g.,
int
#63
; dummy interrupt
bset cm1
; all clocks stopped
/* dummy interrupt handling */
dummy
reit
• When entering stop mode, the instruction queue reads ahead to instructions following the instruction setting the CM10 bit in the CM1 register to "1" (all clocks stopped), and the program stops.
When the microcomputer exits stop mode, the instruction lined in the instruction queue is executed
before the interrupt routine for recovery is done.
Write the JMP.B instruction, as follows, after the instruction setting the CM10 bit in the CM1 register
to "1" (all clocks stopped).
e.g.,
bset 0, prcr
; protection removed
bset 0, cm1
; all clocks stopped
jmp.b LABEL_001
; JMP.B instruction executed (no instuction between JMP.B
; and LABEL.)
LABEL_001:
nop
; NOP (1)
nop
; NOP (2)
nop
; NOP (3)
nop
; NOP (4)
mov.b #0, prcr
; Protection set
•
•
•
Rev. 1.10 Oct. 18, 2005 Page 414 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Clock Generation Circuit)
26.2.6.3 Suggestions for Reducing Power Consumption
The followings are suggestions for reducing power consumption when programming or designing
systems.
Ports: I/O ports maintains the same state despite the microcomputer entering wait mode or stop
mode. Current flows through active output ports. Feedthrough current flows through input ports in a
high-impedance state. Set unassigned ports as input ports and stabilize electrical potential before
entering wait mode or stop mode.
A/D Converter: If the A/D conversion is not performed, set the VCUT bit in the AD0CON1 register
to "0" (no VREF connection). Set the VCUT bit to "1" (VREF connection) and wait at least 1µs before
starting the A/D conversion.
D/A Converter: Set the DAi bit (i=0, 1) in the DACON register to "0" (output disabled) and set the
DAi register to "0016" when the D/A conversion is not performed.
Peripheral Function Stop: Set the CM02 bit in the CM0 register while in wait mode to stop unnecessary peripheral functions. However, this does not reduce power consumption because the peripheral function clock (fc32) generating from the sub clock does not stop. When in low-speed mode
and low-power consumption mode, do not enter wait mode when the CM02 bit is set to "1" (peripheral clock stops in wait mode).
Rev. 1.10 Oct. 18, 2005 Page 415 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Protection)
26.3 Protection
The PRC2 bit setting in the PRCR register is changed to "0" (write disabled) when an instruction is written
to any address after the PRC2 bit is set to "1" (write enabled). Write instruction immediately after setting the
PRC2 bit to "1" to change registers protected by the PRC2 bit. Do not generate an interrupt or a DMA
transfer between the instruction to set the PRC2 bit to "1" and the next instruction.
Rev. 1.10 Oct. 18, 2005 Page 416 of 435
REJ09B0162-0110
26. Precautions (Interrupts)
M32C/88 Group (M32C/88T)
26.4 Interrupts
26.4.1 ISP Setting
After reset, the ISP is set to "00000016". The program runs out of control if an interrupt is acknowledged
before the ISP is set. Therefore, the ISP must be set before an interrupt request is generated. Set the ISP
to an even address, which allows interrupt sequences to be executed at a higher speed.
_______
_______
To use NMI interrupt, set the ISP at the beginning of the program. The NMI interrupt can be acknowledged after the first instruction has been executed after reset.
_______
26.4.2 NMI Interrupt
_______
_______
• NMI interrupt cannot be denied. Connect the NMI pin to VCC via a resistor (pull-up) when not in use.
_______
• The P8_5 bit in the P8 register indicates the NMI pin value. Read the P8_5 bit only to determine the pin
_______
level after a NMI interrupt occurs.
_______
• "H" and "L" signals applied to the NMI pin must be over 2 CPU clock cycles + 300 ns wide.
_______
• NMI interrupt request may not be acknowledged if this and other interrupt requests are generated
simultaneously.
______
26.4.3 INT Interrupt
• Edge Sensitive
______
______
"H" and "L" signals applied to the INT0 to INT5 pins must be at least 250 ns wide, regardless of the CPU
clock.
• Level Sensitive
______
______
"H" and "L" signals applied to the INT0 to INT5 pins must be at least 1 CPU clock cycle + 200 ns wide.
For example, "H" and "L" must be at least 234ns wide if XIN=30MHz with no division.
______
______
• The IR bit setting may change to "1" (interrupt requested) when switching the polarity of the INT0 to INT5
pins. Set the IR bit to "0" (no interrupt requested) after selecting the polarity. Figure 26.3 shows an
______
example of the switching procedure for the INT interrupt.
Set the ILVL2 to ILVL0 bits in the INTiIC
register (i = 0 to 5) to "0002" (level 0)
(INT interrupt disabled)
Set the POL bit in the INTiIC register
Set the IR bit in the INTiIC register to "0"
Set the ILVL2 to ILVL0 bits to "0012" (level 1)
to "1112" (level 7)
(INT interrupt request acknowledgement enabled)
______
Figure 26.2 Switching Procedure for INT Interrupt
Rev. 1.10 Oct. 18, 2005 Page 417 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Interrupts)
26.4.4 Watchdog Timer Interrupt
Reset the watchdog timer after a watchdog timer interrupt occurs.
26.4.5 Changing Interrupt Control Register
To change the interrupt control register while the interrupt request is denied, follow the instructions below.
Changing IR bit
The IR bit setting may not change to "0" (no interrupt requested) depending on the instructions written.
If this is a problem, use the following instruction to change the register: MOV
Changing Bits Except IR Bit
When an interrupt request is generated while executing an instruction, the IR bit may not be set to "1"
(interrupt requested) and the interrupt may be ignored. If this is a problem, use the following instructions
to change the register: AND, OR, BCLR, BSET
26.4.6 Changing IIOiIR Register (i = 0 to 6, 8 to 11)
Use the following instructions to set bits 1 to 7 in the IIOilR register to "0" (no interrupt requested): AND,
BCLR
26.4.7 Changing RLVL Register
The DMAII bit is indeterminate after reset. When using the DMAII bit to generate an interrupt, set the
interrupt control register after setting the DMAII bit to "0" (interrupt priority level 7 available for interrupts).
Rev. 1.10 Oct. 18, 2005 Page 418 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (DMAC)
26.5 DMAC
• Set DMAC-associated registers while the MDi1 and MDi0 bits (i=0 to 3) in the channel to be used are set
to "002" (DMA disabled). Set the MDi1 and MDi0 bits to "012" (single transfer) or "112" (repeat transfer)
at the end of setup procedure to start DMA requests.
• Do not set the DRQ bit in the DMiSL register to "0" (no request).
If a DMA request is generated but the receiving channel is not ready to receive(1), the DMA transfer does
not occur and the DRQ bit is set to "0".
NOTE:
1. The MDi1 and MDi0 bits are set to "002" or the DCTi register is set to "000016" (transferred 0
times).
• To start a DMA transfer by a software trigger, set the DSR bit and DRQ bit in the DMiSL register to "1"
simultaneously.
e.g.,
OR.B #0A0h,DMiSL
; Set the DSR and DRQ bits to "1" simultaneously
• Do not generate a channel i DMA request when setting the MDi1 and MDi0 bits in the DMDj register
(j=0,1) corresponding to channel i to "012" (single transfer) or "112" (repeat transfer), if the DCTi register
of channel i is set to "1".
• Select the peripheral function which causes the DMA request after setting the DMA-associated regis______
ters. If none of the conditions above (setting INT interrupt as DMA request source) apply, do not write
"1" to the DCTi register.
• Enable DMA(2) after setting the DMiSL register (i=0 to 3) and waiting six BCLK cycles or more by
program.
NOTE:
2. DMA is enabled when the values set in the MDi1 and MDi0 bits in the DMDj register are
changed from "002" (DMA disabled) to "012" (single transfer) or "112" (repeat transfer).
Rev. 1.10 Oct. 18, 2005 Page 419 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Timer)
26.6 Timer
26.6.1 Timers A and B
Timers stop after reset. Set the TAiS(i=0 to 4) bit or TBjS(j=0 to 5) bit in the TABSR register or TBSR
register to "1" (starts counting) after setting operating mode, count source and counter.
The following registers and bits must be set while the TAiS bit or TBjS bit is set to "0" (stops counting).
• TAiMR, TBjMR register
• TAi, TBj register
• UDF register
• TAZIE, TA0TGL, TA0TGH bits in the ONSF register
• TRGSR register
26.6.2 Timer A
The TA1OUT, TA2OUT and TA4OUT pins are placed in high-impedance states when a low-level ("L") signal
_______
is applied to the NMI pin while the INV03 and INV02 bits in the INVC0 register are set to "112" (forced
_______
cutoff of the three-phase output by an "L" signal applied to the NMI pin).
26.6.2.1 Timer A (Timer Mode)
• The TAiS bit (i=0 to 4) in the TABSR register is set to "0" (stops counting) after reset. Set the TAiS
bit to "1" (starts counting) after selecting an operating mode and setting the TAi register.
• The TAi register indicates the counter value during counting at any given time. However, the
counter is "FFFF16" when reloading. The setting value can be read after setting the TAi register
while the counter stops and before the counter starts counting.
26.6.2.2 Timer A (Event Counter Mode)
• The TAiS (i=0 to 4) bit in the TABSR register is set to "0" (stops counting) after reset. Set the TAiS
bit to "1" (starts counting) after selecting an operating mode and setting the TAi register.
• The TAi register indicates the counter values during counting at any given time. However, the
counter will be "FFFF16" during underflow and "000016" during overflow, when reloading. The setting value can be read after setting the TAi register while the counter stops and before the counter
starts counting.
Rev. 1.10 Oct. 18, 2005 Page 420 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Timer)
26.6.2.3 Timer A (One-shot Timer Mode)
• The TAiS (i=0 to 4) bit in the TABSR register is set to "0" (stops counting) after reset. Set the TAiS
bit to "1" (starts counting) after selecting an operating mode and setting the TAi register.
• The followings occur when the TABSR register is set to "0" (stops counting) while counting:
- The counter stops counting and the microcomputer reloads contents of the reload register.
- The TAiOUT pin becomes low ("L").
- The IR bit in the TAiIC register is set to "1" (interrupt requested) after one CPU clock cycle.
• The output of the one-shot timer is synchronized with an internal count source. When set to an
external trigger, there is a delay of one count source cycle maximum, from trigger input to the TAiIN
pin to the one-shot timer output.
• The IR bit is set to "1" when the following procedures are performed to set timer mode:
- selecting one-shot timer mode after reset.
- switching from timer mode to one-shot timer mode.
- switching from event counter mode to one-shot timer mode.
Therefore, set the IR bit to "0" to generate a timer Ai interrupt (IR bit) after performing these procedures.
• When a trigger is generated while counting, the reload register reloads and continues counting
after the counter has decremented once following a re-trigger. To generate a trigger while counting,
wait at least 1 count source cycle after the previous trigger has been generated and generate a retrigger.
• If an external trigger input is selected to start counting in timer A one-shot timer mode, do not
provide another external trigger input again for 300 ns before the timer A counter value reaches
"000016". One-shot timer may stop counting.
26.6.2.4 Timer A (Pulse Width Modulation Mode)
• The TAiS(i=0 to 4) bit in the TABSR register is set to "0" (stops counting) after reset. Set the TAiS bit
to "1" (starts counting) after selecting an operating mode and setting the TAi register.
• The IR bit is set to "1" when the following procedures are performed to set timer mode:
- Selecting PWM mode after reset
- Switching from timer mode to PWM mode
- Switching from event counter mode to PWM mode
Therefore, set the IR bit to "0" by program to generate a timer Ai interrupt (IR bit) after performing
these procedures.
• The followings occur when the TAiS bit is set to "0" (stops counting) while PWM pulse is output:
- The counter stops counting
- Output level changes to low ("L") and the IR bit changes to "1" when the TAiOUT pin is held high ("H")
- The IR bit and the output level remain unchanged when TAiOUT pin is held "L"
Rev. 1.10 Oct. 18, 2005 Page 421 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Timer)
26.6.3 Timer B
26.6.3.1 Timer B (Timer Mode, Event Counter Mode)
• The TBiS (i=0 to 5) bit is set to "0" (stops counting) after reset. Set the TBiS bit to "1" (starts
counting) after selecting an operating mode and setting TBi register.
The TB2S to TB0S bits are bits 7 to 5 in the TABSR register. The TB5S to TB3S bits are bits 7 to 5
in the TBSR register.
• The TBi register indicates the counter value during counting at any given time. However, the
counter is "FFFF16" when reloading. The setting value can be read after setting the TBi register
while the counter stops and before the counter starts counting.
26.6.3.2 Timer B (Pulse Period/Pulse Width Measurement Mode)
• The IR bit in the TBiIC (i=0 to 5) register is set to "1" (interrupt requested) when the valid edge of a
pulse to be measured is input and when the timer Bi counter overflows. The MR3 bit in the TBiMR
register determines the interrupt source within an interrupt routine.
• Use another timer to count how often the timer counter overflows when an interrupt source cannot
be determined by the MR3 bit, such as when a pulse to be measured is input at the same time the
timer counter overflows.
• To set the MR3 bit in the TBiMR register to "0" (no overflow), set the TBiMR register after the MR3
bit is set to "1" (overflow) and one or more cycles of the count source are counted, while the TBiS
bits in the TABSR and TBSR registers are set to "1" (starts counting).
• The IR bit in the TBiIC register is used to detect overflow only. Use the MR3 bit only to determine
interrupt source within an interrupt routine.
• Indeterminate values are transferred to the reload register during the first valid edge input after
counting is started. Timer Bi interrupt request is not generated at this time.
• The counter value is indeterminate when counting is started. Therefore, the MR3 bit setting may
change to "1" (overflow) and causes timer Bi interrupt requests to be generated until a valid edge is
input after counting is started.
• The IR bit may be set to "1" (interrupt requested) if the MR1 and MR0 bits in the TBiMR register are
set to a different value after a count begins. If the MR1 and MR0 bits are rewritten, but to the same
value as before, the IR bit remains unchanged.
• Pulse width measurement measures pulse width continuously. Use program to determine whether
measurement results are high ('"H") or low ("L").
Rev. 1.10 Oct. 18, 2005 Page 422 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Serial I/O)
26.7 Serial I/O
26.7.1 Clock Synchronous Serial I/O Mode
_______
The RTS2 and CLK2 pins are placed in high-impedance states when a low-level ("L") signal is applied to
______
the NMI pin while the INV03 to INV02 bits in the INVC0 register are set to "112" (forced cutoff of the three_______
phase output by an "L" signal applied to the NMI pin).
26.7.1.1 Transmission /Reception
_______
________
When the RTS function is used while an external clock is selected, the output level of the RTSi pin is
held "L" indicating that the microcomputer is ready for reception. The transmitting microcomputer is
________
notified that reception is possible. The output level of the RTSi pin becomes high ("H") when reception
________
________
begins. Therefore, connecting the RTSi pin to the CTSi pin of the transmitting microcomputer synchro_______
nizes transmission and reception. The RTS function is disabled if an internal clock is selected.
26.7.1.2 Transmission
When an external clock is selected while the CKPOL bit in the UiC0 (i=0 to 4) register is set to "0" (data
is transmitted on the falling edge of the transfer clock and received on the rising edge) and the external
clock is held "H", or when the CKPOL bit is set to "1" (data is transmitted on the rising edge of the
transfer clock and received on the falling edge) and the external clock is held "L", meet the following
conditions:
• Set the TE bit in the UiC1 register to "1" (receive enabled)
• Set the TI bit in the UiC1 register to "0" (data in the UiTB register)
________
________
• Apply "L" signal to the CTSi pin if the CTS function is selected
26.7.1.3 Reception
Activating the transmitter in clock synchronous serial I/O mode generates the shift clock. Therefore,
set for transmission even if the microcomputer is used for reception only. Dummy data is output from
the TxDi pin while receiving.
If an internal clock is selected, the shift clock is generated when the TE bit in the UiC1 registers is set
to "1" (receive enabled) and dummy data is set in the UiTB register. If an external clock is selected, the
shift clock is generated when the external clock is input into CLKi pin while the TE bit is set to "1"
(receive enabled) and dummy data is set in the UiTB register.
When receiving data consecutively while the RE bit in the UiC1 register is set to "1" (data in the UiRB
register) and the next data is received by the UARTi reception register, an overrun error occurs and
the OER bit in the UiRB register is set to "1" (overrun error). In this case, the UiRB register is indeterminate. When overrun error occurs, program both reception and transmission registers to retransmit
earlier data. The IR bit in the SiRIC does not change when an overrun error occurs.
When receiving data consecutively, feed dummy data to the low-order byte in the UiTB register every
time a reception is made.
When an external clock is selected while the CKPOL bit in the UiC0 register is set to "0" (data is
transmitted on the falling edge of the transfer clock and received on the rising edge) and the external
clock is held "H" or when the CKPOL bit is set to "1" (data is transmitted on the rising edge of the
transfer clock and received on the falling edge) and the external clock is held "L", meet the following
conditions:
• Set the RE bit in the UiC1 register to "1" (receive enabled)
• Set the TE bit in the UiC1 register to "1" (transmit enabled)
• Set the TI bit in the UiC1 register to "0" (data in the UiTB register)
Rev. 1.10 Oct. 18, 2005 Page 423 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Serial I/O)
26.7.2 UART Mode
Set the UiERE bit (i=0 to 4) in the UiC1 register after setting the UiMR register.
26.7.3 Special Mode 1 (I2C Mode)
To generate the start condition, stop condition or restart condition, set the STSPSEL bit in the UiSMR4
register to "0" first. Then, change each condition generating bit (the STAREQ bit, STPREQ bit or
RSTAREQ bit) setting from "0" to "1" after going through a half cycle of the transfer clock.
Rev. 1.10 Oct. 18, 2005 Page 424 of 435
REJ09B0162-0110
26. Precautions (A/D Converter)
M32C/88 Group (M32C/88T)
26.8 A/D Converter
• Set the AD0CON0 (bit 6 excluded), AD0CON1, AD0CON2, AD0CON3, and AD0CON4 registers while
the A/D conversion is stopped (before a trigger is generated).
• Wait a minimum of 1µs before starting the A/D conversion when changing the VCUT bit setting in the
AD0CON1 register from "0" (VREF no connection) to "1" (VREF connection).
Change the VCUT bit setting from "1" to "0" after the A/D conversion is completed.
• Insert capacitors between the AVCC pin, VREF pin, analog input pin ANij (i=none, 0, 2, 15; j=0 to 7) and
AVSS pin to prevent latch-ups and malfunctions due to noise, and to minimize conversion errors. The
same applies to the VCC and VSS pins. Figure 26.4 shows the use of capacitors to reduce noise.
Microcomputer
VCC
VCC
VCC
AVCC
VSS
VREF
C4
C1
C2
AVSS
VCC
C3
VCC
C5
ANi
VSS
ANi: ANi, AN0i, AN15i and AN2i (i=0 to 7)
NOTES:
1. C1≥0.47µF, C2≥0.47µF, C3≥100pF, C4≥0.1µF, C5≥0.1µF (reference)
2. Use thick and shortest possible wiring to connect capacitors.
Figure 26.3 Use of Capacitors to Reduce Noise
• Set the bit in the port direction register, which corresponds to the pin being used as the analog input, to
__________
"0" (input mode). Set the bit in the port direction register, which corresponds to the ADTRG pin, to "0"
(input mode) if the TRG bit in the AD0CON0 register is set to "1" (external trigger).
• When generating a key input interrupt, do not use the AN4 to AN7 pins as analog input pins (key input
interrupt request is generated when the A/D input voltage becomes "L").
• The φAD frequency must be 16MHz or less. When the sample and hold function is not activated, the φAD
frequency must be 250 kHz or more. If the sample and hold function is activated, the φAD frequency
must be 1MHz or more.
• Set the CH2 to CH0 bits in the AD0CON0 register or the SCAN1 and SCAN0 bits in the AD0CON1
register to re-select analog input pins when changing A/D conversion mode.
Rev. 1.10 Oct. 18, 2005 Page 425 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (A/D Converter)
• AVCC = VREF = VCC,
A/D input voltage (for AN0 to AN7, AN00 to AN07, and AN20 to AN27, AN150 to AN157, ANEX0, and
ANEX1) ≤ VCC.
• Wrong values are stored in the AD0i register (i=0 to 7) if the CPU reads the AD0i register while the AD0i
register stores results from a completed A/D conversion. This occurs when the CPU clock is set to a
divided main clock or a sub clock.
In one-shot mode or single sweep mode, read the corresponding AD0i register after verifying that the A/D
conversion has been completed. The IR bit in the AD0IC register determines the completion of the A/D
conversion.
In repeat mode, repeat sweep mode 0, repeat sweep mode 1, multi-port single sweep mode, and multiport repeat sweep mode 0, use an undivided main clock as the CPU clock.
• Conversion results of the A/D converter are indeterminate if the ADST bit in the AD0CON0 register is set
to "0" (A/D conversion stopped) and the conversion is forcibly terminated by program during the A/D
conversion. The AD0i register not performing the A/D conversion may also be indeterminate.
If the ADST bit is changed to "0" by program, during the A/D conversion, do not use any values obtained
from the AD0i registers.
• External triggers cannot be used in DMAC operating mode. Do not read the AD00 register by program.
• Do not perform the A/D conversion in wait mode.
• Set the MCD4 to MCD0 bits in the MCD register to "100102" (no division) if using the sample and hold
function.
• Do not acknowledge any interrupt requests, even if generated, before setting the ADST bit, if the A/D
conversion is terminated by setting the ADST bit in the AD0CON0 register to "0" (A/D conversion
stopped) while the microcomputer is A/D converting in single sweep mode.
Rev. 1.10 Oct. 18, 2005 Page 426 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Intelligent I/O)
26.9 Intelligent I/O
26.9.1 Register Setting
Operations, controlled by the values written to the G1BT, G1BCR1, G1TMCR0 to G1TMCR7, G1TPR6,
G1TPR7, G1TM0 to G1TM7, G1POCR0 to G1POCR7, G1PO0 to G1PO7, G1FS and G1FE registers,
are affected by the count source (fBT1) set in the BCK1 and BCK0 bits in the G1BCR0 register.
Set the BCK1 and BCK0 bits before setting the G1BT, G1BCR1, G1TMCR0 to G1TMCR7, G1TPR6,
G1TPR7, G1TM0 to G1TM7, G1POCR0 to G1POCR7, G1PO0 to G1PO7, G1FS and G1FE registers.
Operations, controlled by the values written to the G0RI and G1RI, G0TO and G1TO, G0CR and G1CR,
G0RB and G1RB, G0MR and G1MR, G0EMR and G1EMR, G0ETC and G1ETC, G0ERC and G1ERC,
G0IRF, G1IRF, G0TB and G1TB, G0CMP0 to G0CMP3, G1CMP0 to G1CMP3, G0MSK0 and G0MSK1,
G1MSK0 and G1MSK1, G0TCRC and G1TCRC, G0RCRC and G1RCRC registers are affected by the
transfer clock.
Set trasfer clock before setting the G0RI and G1RI, G0TO and G1TO, G0CR and G1CR, G0RB and
G1RB, G0MR and G1MR, G0EMR and G1EMR, G0ETC and G1ECT, G0ERC and G1ERC, G0IRF and
G1IRF, G0TB and G1TB, G0CMP0 to G0CMP3, G1CMP0 to G1CMP3, G0MSK0 and G0MSK1,
G1MSK0 and G1MSK1, G0TCRC and G1TCRC, G0RCRC and G1RCRC registers.
Rev. 1.10 Oct. 18, 2005 Page 427 of 435
REJ09B0162-0110
26. Precautions (Programmable I/O Ports)
M32C/88 Group (M32C/88T)
26.10 Programmable I/O Ports
• Because ports P72 to P75, P80, and P81 have three-phase PWM output forced cutoff function, they are
_______
affected by the three-phase motor control timer function and the NMI pin when these ports are set for
output functions (port output, timer output, three-phase PWM output, serial I/O output, intelligent I/O
output).
_______
Table 26.4 shows the INVC0 register setting, the NMI pin input level and the state of output ports.
_______
Table 26.3 INVC0 Register and the NMI Pin
Setting Value of the INVC0 Register
INV02 Bit
INV03 Bit
Signal level Applied
to the NMI Pin
P72 to P75, P80, P81 Pin States
(When Setting Them as Output Pins)
0
(Not Using the Three-Phase
Motor Control Timer
Functions)
-
-
Provides functions selected by the
PS1, PSL1, PSC, PS2, PSL2
registers
1
(Using the Three-Phase
Motor Control Timer
Functions)
0
(Three-Phase Motor Control
Timer Output Disabled)
-
High-impedance state
1
(Three-Phase Motor Control
Timer Output Enabled)(1)
H
Provides functions selected by the
PS1, PSL1, PSC, PS2, PSL2
registers
L
High-impedance state
(Forcibly Terminated)
NOTE:
_______
1. The INV03 bit is set to "0" after a low-level ("L") signal is applied to the NMI pin.
• The availability of pull-up resistors is indeterminate until internal power voltage stabilizes, if the RESET
pin is held "L".
• The input threshold voltage varies between programmable I/O ports and peripheral functions. Therefore, if the lelvel of the voltage applied to a pin shared by both programmable I/O ports and peripheral
functions is not within the recommended operating condition, VIH and VIL (neither "H" nor "L"), the level
may vary depending on the programmable ports and peripheral functions.
Rev. 1.10 Oct. 18, 2005 Page 428 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Flash Memory Version)
26.11 Flash Memory Version
26.11.1 Boot Mode
I/O pins may not be placed in high-impedance states until internal voltage stabilizes, when power is
turned on in boot mode. Use the following procedure to turn on power in boot mode.
____________
1) Apply an low-level ("L") signal to the RESET and the CNVSS pin
2) Wait a minimum of 2 ms after VCC reaches 2.7V or above (until internal voltage stabilizes)
3) Apply a high-level ("H") signal to the CNVSS pin
____________
4) Apply an "H" signal to the RESET pin (reset exited)
Rev. 1.10 Oct. 18, 2005 Page 429 of 435
REJ09B0162-0110
M32C/88 Group (M32C/88T)
26. Precautions (Noise)
26.12 Noise
Connect a bypass capacitor (0.1µF or more) between VCC and VSS by shortest path, using thick wires.
Rev. 1.10 Oct. 18, 2005 Page 430 of 435
REJ09B0162-0110
Package Dimensions
M32C/88 Group (M32C/88T)
Package Dimensions
JEITA Package Code
P-LQFP144-20x20-0.50
RENESAS Code
PLQP0144KA-A
Previous Code
144P6Q-A / FP-144L / FP-144LV
MASS[Typ.]
1.2g
HD
*1
D
108
73
109
NOTE)
1. DIMENSIONS "*1" AND "*2"
DO NOT INCLUDE MOLD FLASH.
2. DIMENSION "*3" DOES NOT
INCLUDE TRIM OFFSET.
72
bp
c
Reference
Symbol
*2
E
HE
c1
b1
Terminal cross section
Index mark
c
36
A
1
ZD
ZE
37
A2
144
D
E
A2
HD
HE
A
A1
bp
b1
c
c1
A1
F
L
L1
e
x
y
ZD
ZE
L
L1
*3
e
bp
y
JEITA Package Code
P-LQFP100-14x14-0.50
RENESAS Code
PLQP0100KB-A
Detail F
x
Previous Code
100P6Q-A / FP-100U / FP-100UV
Dimension in Millimeters
Min Nom Max
19.9 20.0 20.1
19.9 20.0 20.1
1.4
21.8 22.0 22.2
21.8 22.0 22.2
1.7
0.05 0.1 0.15
0.17 0.22 0.27
0.20
0.09 0.145 0.20
0.125
0°
8°
0.5
0.08
0.10
1.25
1.25
0.35 0.5 0.65
1.0
MASS[Typ.]
0.6g
HD
*1
D
51
75
NOTE)
1. DIMENSIONS "*1" AND "*2"
DO NOT INCLUDE MOLD FLASH.
2. DIMENSION "*3" DOES NOT
INCLUDE TRIM OFFSET.
50
76
bp
HE
Reference
Symbol
c
c1
*2
E
b1
D
E
A2
HD
HE
A
A1
bp
b1
c
c1
100
26
1
ZE
Terminal cross section
25
Index mark
ZD
y
e
*3
bp
A1
c
A
A2
F
L
x
L1
Detail F
Rev. 1.10 Oct. 18, 2005 Page 431 of 435
REJ09B0162-0110
e
x
y
ZD
ZE
L
L1
Dimension in Millimeters
Min Nom Max
13.9 14.0 14.1
13.9 14.0 14.1
1.4
15.8 16.0 16.2
15.8 16.0 16.2
1.7
0.05 0.1 0.15
0.15 0.20 0.25
0.18
0.09 0.145 0.20
0.125
0°
8°
0.5
0.08
0.08
1.0
1.0
0.35 0.5 0.65
1.0
Register Index
M32C/88 Group (M32C/88T)
Register Index
A
AD00 to AD07 225
AD0CON0 221
AD0CON1 222
AD0CON2 223
AD0CON3 224
AD0CON4 225
AIER 98
C
C0AFS 336
C0BPR 307
C0CONR 305
C0CTLR0 296
C0CTLR1 299
C0EFR 315
C0EIMKR 313
C0EISTR 314
C0GMR0 320
C0GMR1 321
C0GMR2 322
C0GMR3 323
C0GMR4 324
C0IDR 304
C0LMAR0 320
C0LMAR1 321
C0LMAR2 322
C0LMAR3 323
C0LMAR4 324
C0LMBR0 320
C0LMBR1 321
C0LMBR2 322
C0LMBR3 323
C0LMBR4 324
C0MCTL0 to C0MCTL15
C0MDR 316
C0REC 309
C0SBS 331
C0SIMKR 312
C0SISTR 310
C0SLOT0_0 332
C0SLOT0_1 332
C0SLOT0_2 333
327
Rev. 1.10 Oct. 18, 2005 Page 432 of 435
REJ09B0162-0110
C0SLOT0_3 333
C0SLOT0_4 334
C0SLOT0_5 334
C0SLOT0_6 to C0SLOT0_13 335
C0SLOT0_14 335
C0SLOT0_15 335
C0SLOT1_0 332
C0SLOT1_1 332
C0SLOT1_2 333
C0SLOT1_3 333
C0SLOT1_4 334
C0SLOT1_5 334
C0SLOT1_6 to C0SLOT1_13 335
C0SLOT1_14 335
C0SLOT1_15 335
C0SLPR 300
C0SSCTLR 318
C0SSSTR 319
C0STR 301
C0TEC 309
C0TSR 308
C1AFS 336
C1BRP 307
C1CONR 305
C1CTLR0 296
C1CTLR1 299
C1EFR 315
C1EIMKR 313
C1EISTR 314
C1GMR0 320
C1GMR1 321
C1GMR2 322
C1GMR3 323
C1GMR4 324
C1IDR 304
C1LMAR0 320
C1LMAR1 321
C1LMAR2 322
C1LMAR3 323
C1LMAR4 324
C1LMBR0 320
C1LMBR1 321
C1LMBR2 322
C1LMBR3 323
Register Index
M32C/88 Group (M32C/88T)
C1LMBR4 324
C1MCTL0 to C1MCTL15 327
C1MDR 316
C1REC 309
C1SBS 331
C1SIMKR 312
C1SISTR 310
C1SLOT0_0 332
C1SLOT0_1 332
C1SLOT0_2 333
C1SLOT0_3 333
C1SLOT0_4 334
C1SLOT0_5 334
C1SLOT0_6 to C1SLOT0_13 335
C1SLOT0_14 335
C1SLOT0_15 335
C1SLOT1_0 332
C1SLOT1_1 332
C1SLOT1_2 333
C1SLOT1_3 333
C1SLOT1_4 334
C1SLOT1_5 334
C1SLOT1_6 to C1SLOT1_13 335
C1SLOT1_14 335
C1SLOT1_15 335
C1SLPR 300
C1SSCTLR 318
C1SSSTR 319
C1STR 301
C1TEC 309
C1TSR 308
C2AFS 336
C2BRP 307
C2CONR 305
C2CTLR0 296
C2CTLR1 299
C2EFR 315
C2EIMKR 313
C2EISTR 314
C2GMR0 320
C2GMR1 321
C2GMR2 322
C2GMR3 323
C2GMR4 324
C2IDR 304
C2LMAR0 320
Rev. 1.10 Oct. 18, 2005 Page 433 of 435
REJ09B0162-0110
C2LMAR1 321
C2LMAR2 322
C2LMAR3 323
C2LMAR4 324
C2LMBR0 320
C2LMBR1 321
C2LMBR2 322
C2LMBR3 323
C2LMBR4 324
C2MCTL0 to C2MCTL15 327
C2MDR 316
C2REC 309
C2SBS 331
C2SIMKR 312
C2SISTR 310
C2SLOT0_0 332
C2SLOT0_1 332
C2SLOT0_2 333
C2SLOT0_3 333
C2SLOT0_4, 334
C2SLOT0_5 334
C2SLOT0_6 to C2SLOT0_13 335
C2SLOT0_14 335
C2SLOT0_15 335
C2SLOT1_0 332
C2SLOT1_1 332
C2SLOT1_2 333
C2SLOT1_3 333
C2SLOT1_4 334
C2SLOT1_5 334
C2SLOT1_6 to C2SLOT1_13 335
C2SLOT1_14 335
C2SLOT1_15 335
C2SLPR 300
C2SSCTLR 318
C2SSSTR 319
C2STR 301
C2TEC 309
C2TSR 308
CCS 281
CM0 56, 105
CM1 57
CM2 59
CPSRF 60
CRCD 240
CRCIN 240
Register Index
M32C/88 Group (M32C/88T)
D
DA0, DA1 239
DACON 239
DCT0 to DCT3 112
DM0SL to DM3SL 109
DMA0 to DMA3 113
DMD0, DMD1 111
DRA0 to DRA3 113
DRC0 to DRC3 112
DSA0 to DSA3 113
DTT 159
F
FMR0 374
FMR1 375
G
G0CMP0 to G0CMP3 280
G0CR, G1CR 273
G0DR, G1DR 279
G0EMR 275
G0ERC, G1ERC 277
G0ETC 276
G0IRF 278
G0MR 274
G0MSK0, G0MSK1 280
G0RB, G1RB 273
G0RCRC, G1RCRC 280
G0RI, G1RI 272
G0TB, G1TB 279
G0TCRC, G1TCRC 280
G0TO, G1TO 272
G1BCR0 248
G1BCR1 249
G1BT 248
G1CMP0 to G1CMP3 280
G1EMR 275
G1ETC 276
G1FE 253
G1FS 252
G1IRF 279
G1MR 274
G1MSK0, G1MSK1 280
G1PO0 to G1PO7 252
Rev. 1.10 Oct. 18, 2005 Page 434 of 435
REJ09B0162-0110
G1POCR0 to G1POCR7 251
G1TM0 to G1TM7 251
G1TMCR0 to G1TMCR7 250
G1TPR6, G1TPR7 250
I
ICTB2 160
IDB0, IDB1 159
IFSR 96, 174
IIO0IE to IIO6IE, IIO8IE to IIO11IE 102
IIO0IR to IIO6IR, IIO8IR to IIO11IR 101
Interrupt Control 87, 88
INVC0 157
INVC1 158
IPS 363
IPSA 364
M
MCD
58
O
ONSF
131
P
P0 to P15 352
PCR 363
PD0 to PD15 351
PLC0 61
PLC1 61
PM0 51
PM1 52
PM2 62
PRCR 78
PS0 353
PS1 353
PS2 354
PS3 354
PS5 355
PS8 355
PS9 356
PSC 359
PSC2 359
PSC3 360
PSD1 360
PSL0 357
Register Index
M32C/88 Group (M32C/88T)
PSL1
PSL2
PSL3
PUR0
PUR1
PUR2
PUR3
PUR4
357
358
358
361
361
361
362
362
R
RLVL 89, 119
RMAD0 to RMAD7 98
ROMCP 372
T
TA0 to TA4 129
TA0MR to TA4MR 130, 135, 138, 141, 143
TA1, TA2, TA4, TA11, TA21, TA41 160
TA1MR, TA2MR, TA4MR 162
TABSR 130, 146, 161
TB0 to TB5 145
TB0MR to TB5MR 146, 148, 150, 152
TB2 161
TB2MR 162
TB2SC 160
TBSR 147
TCSPR 60, 132
TRGSR 132, 161
U
U0BRG to U4BRG 168
U0C0 to U4C0 169
U0C1 to U4C1 170
U0MR to U4MR 168
U0RB to U4RB 167
U0SMR to U4SMR 170
U0SMR2 to U4SMR2 171
U0SMR3 to U4SMR3 172
U0SMR4 to U4SMR4 173
U0TB to U4TB 167
UDF 131
W
WDC 48, 104
WDTS 104
Rev. 1.10 Oct. 18, 2005 Page 435 of 435
REJ09B0162-0110
X
X0R to X15R 242
XYC 242
Y
Y0R to Y15R
242
REVISION HISTORY
Rev.
Date
1.10
Oct., 05
M32C/88 Group(M32C/88T) Hardware Manual
Description
Summary
Page
New Document
C-1
RENESAS 16/32-BIT SINGLE-CHIP MICROCOMPUTER
HARDWARE MANUAL
M32C/88 Group (M32C/88T)
Publication Data :
Rev.1.10 Oct. 18, 2005
Published by : Sales Strategic Planning Div.
Renesas Technology Corp.
© 2005. Renesas Technology Corp., All rights reserved. Printed in Japan.
M32C/88 Group (M32C/88T)
Hardware Manual
2-6-2, Ote-machi, Chiyoda-ku, Tokyo, 100-0004, Japan