规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDBF08018A63 SF6-3 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2009-2-27 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 8 SAW FILTER HDBF08018A63 SF6-3 更改内容描述 Modify Content 备注 Remark 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 2 of 8 SAW FILTER HDBF08018A63 SF6-3 1. SCOPE This specification shall cover the characteristics of SAW filter BF08018A63 2. ELECTRICAL SPECIFICATION DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V 10V50Hz/60Hz -40℃ to +85℃ -40℃ to +85℃ 0dBm Electronic Characteristics Parameter Center Frequency Insertion Loss -1.5dB Bandwidth -3dB Bandwidth -35 dB Bandwidth -40dB Bandwidth Passband Variation Group Delay Variation Absolute Delay Ultimate Rejection Subatrate Material Ambient Temperature www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 Min 79.90 18.0 18.3 - Typ 80.00 28.5 18.18 18.33 19.12 19.2 1.0 100 3.6 48 YZ 25 E-mail:[email protected] Max 80.10 30.0 19.2 19.4 1.5 - Units MHz dB MHz MHz MHz MHz dB nsec usec dB ℃ Page 3 of 8 SAW FILTER HDBF08018A63 SF6-3 3. DIMENSION 4.TEST CIRCUIT L1=L2=68nH 5. ENVIRONMENTAL CHARACTERISTICS 5-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in table 1. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 8 SAW FILTER HDBF08018A63 SF6-3 5-2 Low temperature exposure Subject the device to -20℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in table 1. 5-3 Temperature cycling Subject the device to a low temperature of -40℃for 30 minutes. Following by a high temperature of +80℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in table 1. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in table 1. 5-5 Solderability Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in table 1. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in table 1. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in table 1. 5-8 Lead fatigue 5-8-1 Pulling test Weight along with the direction of lead without an shock 1kg. The device shall satisfy all the initial Characteristics. 5-8-2 Bending test Lead shall be subject to withstand against 90℃ bending with 450g weight in the direction of thickness. This operation shall be done toward both direction. The device shall show no evidence of damage and shall satisfy all the initial electrical characteristics. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 8 SAW FILTER HDBF08018A63 SF6-3 6.Typical frequency response www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 8 SAW FILTER www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 HDBF08018A63 E-mail:[email protected] SF6-3 Page 7 of 8 SAW FILTER HDBF08018A63 SF6-3 7. REMARK 7.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 7.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 7.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 8