F-215 ® HQDP–020–06.00–SEU–TTR–2–F (0,50 mm) .0197"(HQDP) (0,80 mm) .0315"(EQDP) EQDP–028–06.00–STR–TTL–3–F HQDP, EQDP SERIES ® Q PAIRS TWINAX CABLE ASSEMBLIES ® SPECIFICATIONS For complete specifications see www.samtec.com?EQDP or www.samtec.com?HQDP Cable: 30 AWG twinax micro ribbon Signal Routing: 100Ω Differential Cable Bending Radius: (11,11 mm) 7/16" min Plating: Au over 50µ" (1,27 µm) Ni Current Rating: EQDP = 500 mA per pin HQDP = 800 mA per pin (6 adjacent pins powered) Propagation Delay: 4.67 nsec/meter Operating Temp Range: -25°C to +105°C Skew (pair-to-pair): <10 ps/ft Skew (within a pair): <5 ps/ft EMI Performance: FCC Class A RoHS Compliant: Yes RECOGNITIONS EQDP Mates with: QTE-DP, QSE-DP HQDP Mates with: QTH-DP, QSH-DP Differential Pair routing Note: Cable lengths longer than 40.00" (1 meter) are not supported with S.I. test data. Note: Design your High Speed Cable with Samtec’s High Speed Cable Solutionator® at www.samtec.com/hdr Surface Mount or Edge Mount 30 AWG twinax ribbon cable Rated @ 7dB Insertion Loss EQDP HQDP 10" (0,25 m) 10.00 GHz / 20.00 Gbps 9.50 GHz / 19.00 Gbps Performance data for other cable lengths and complete test data available at www.samtec.com?HQDP or www.samtec.com?EQDP or contact [email protected] Cable Length NO. OF PAIRS TYPE WIRE LENGTH Optional Captive Screw or Screw Mount Option Socket or Terminal END NO. 1 END NO. 2 WIRING OPTION SCREW OPTION –1 Leave blank for no Screw Option For complete scope of recognitions see www.samtec.com/quality HQDP ALSO AVAILABLE (MOV Required) • Pairs • Terminations Contact Samtec. s ocol t o r d P orte p p u S –020, –040, –060 = (0,50 mm) .0197" pitch (20 pairs per bank) HQDP Series EQDP –014, –028, –042, –056 = (0,80 mm) .0315" pitch –“XX.XX” = Wire Length in Inches (43,7 mm) 01.72" minimum (14 pairs per bank) EQDP Series OAL = Wire Length + (20,32) .800 ± (3,81) .150 Wire Length ± (1,27) .050 SAS SATA el Fibre Chann et n er th E ® PCIe ™ nd a iB n fi In report at Download test QDP or ?H m co c. www.samte m?EQDP co c. te m sa www. Specify END ASSEMBLIES from chart END SURFACE MOUNT TTR Terminal, Top, Notch Right TTL Terminal, Top, Notch Left TBR Terminal, Bottom, Notch Right –4 TBL Terminal, Bottom, Notch Left = Pin 1 to Last Pin STR Socket, Top, Notch Right STL Socket, Top, Notch Left SBR Socket, Bottom, Notch Right SBL Socket, Bottom, Notch Left TEU END NO. 2 (–TTR SHOWN) –2 = Pin 1 to Pin 2 END END NO. 1 (–TEU SHOWN) = Pin 1 to Pin 1 TED SEU SED –3 = Pin 1 to Second Last Pin 1 or 2 (HQDP only) Note: This Series is non-standard, non-returnable. WWW.SAMTEC.COM Due to technical progress, all designs, specifications and components are subject to change without notice. –S = End No. 2 –B = Both Ends WIRING REQUIREMENTS WIRING END OPTIONS OPTION EDGE MOUNT Terminal, Edge, Notch Up Terminal, Edge, Notch Down Socket, Edge, Notch Up Socket, Edge, Notch Down –F = End No. 1 3 or 4 TTR, TBL, STL, SBR, TEU, SED to TTR, TBL, STL, SBR, TED, SEU or TTL, TBR, STR, SBL, TED, SEU to TTL, TBR, STR, SBL, TEU, SED TTR, TBL, STL, SBR, TEU, SED to TTL, TBR, STR, SBL, TEU, SED or TTL, TBR, STR, SBL, TED, SEU to TTR, TBL, STL, SBR, TED, SEU