Project Number:

Project Number: Design Qualification Test Report
Requested by: Mark Shireman
Tracking Code: 107636_Report_Rev_2
Date: 2/5/2015
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Product Rev: 0
Lot #: N/A
Tech: Aaron McKim
Part description: SFM/TFM
Test Start: 3/20/2011
Eng: Eric Ming
Qty to test: 45
Test Completed: 4/18/2011
Design Qualification Test Report
SFM/TFM
SFM-150-02-S-D-A/TFM-150-02-S-D-A
Page 1 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
REVISION HISTORY
DATA
REV.NUM.
DESCRIPTION
05/7/2011
1
Initial Issue
PC
02/05/2015
2
Updated the test data
PC
Page 2 of 51
ENG
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
CERTIFICATION
All instruments and measuring equipment were calibrated to National Institute for Standards and Technology (NIST)
traceable standards according to IS0 10012-l and ANSI/NCSL 2540-1, as applicable.
All contents contained herein are the property of Samtec. No portion of this report, in part or in full shall be
reproduced without prior written approval of Samtec.
SCOPE
To perform the following tests: Design Qualification Test, Please see test plan.
APPLICABLE DOCUMENTS
Standards: EIA Publication 364
TEST SAMPLES AND PREPARATION
1)
2)
3)
4)
5)
All materials were manufactured in accordance with the applicable product specification.
All test samples were identified and encoded to maintain traceability throughout the test sequences.
After soldering, the parts to be used for LLCR and DWV/IR testing were cleaned according to TLWI-0001.
Either an automated cleaning procedure or an ultrasonic cleaning procedure may be used.
The automated procedure is used with aqueous compatible soldering materials.
6) Parts not intended for testing LLCR and DWV/IR are visually inspected and cleaned if necessary.
7) Any additional preparation will be noted in the individual test sequences.
8) Solder Information: Lead free
9) Re-Flow Time/Temp: See accompanying profile.
Page 3 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
TYPICAL OVEN PROFILE (Soldering Parts to Test Boards)
Page 4 of 51
Tracking Code: 107636_Report_Rev_2
Part # Being Tested:
Mating Part #:
PCB
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
SQT-140-01-S-D
material)
Part(519
description:
SFM/TFM
TMM-140-01-L-D-SM-A
FLOWCHARTS
PCB-101998-TST-XX
Gas Tight
TEST
STEP
GROUP A
01
02
03
LLCR-1
Gas Tight
LLCR-2
192 Points
Gas Tight = EIA-364-36A
LLCR = EIA-364-23, LLCR
use Keithley 580 in the dry circuit mode, 10 mA Max
IR & DWV
TEST
GROUP A1
STEP
2 Mated Sets
01
GROUP A2
2 Unmated
of Part #
Being Tested
GROUP A3
GROUP B1
2 Unmated of Mating
Part #
2 Mated Sets
Break Down
Pin-to-Pin
Break Down
Pin-to-Pin
Break Down
Pin-to-Pin
Pin-to-Pin
DWV/Break Down
Voltage
DWV/Break Down
Voltage
DWV/Break Down
Voltage
IR & DWV at test voltage
(on both mated sets and on each
connector unmated)
02
Thermal Shock
(Mated and Undisturbed)
03
IR & DWV at test voltage
(on both mated sets and on each
connector unmated)
04
Cyclic Humidity
(Mated and Undisturbed)
05
IR & DWV at test voltage
(on both mated sets and on each
connector unmated)
DWV on Group B1 to be performed at Test Voltage
DWV test voltage is equal to 75% of the lowest break down voltage from Groups A1, A2 or A3
Thermal Shock = EIA-364-32, Table II, Test Condition I:
-55oC to +85oC 1/2 hour dwell, 100 cycles
Humidity = EIA-364-31, Test Condition B (240 Hours)
and Method III (+25°C to +65°C @ 90% RH to 98% RH)
ambient pre-condition and delete steps 7a and 7b
IR = EIA-364-21
DWV = EIA-364-20, Test Condition 1
Page 5 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
FLOWCHARTS Continued
Durability/Mating/Unmating/Gaps
TEST
GROUP A1
GROUP A2
GROUP A3
STEP
8 Boards
(largest position submitted)
8 Boards
(middle position submitted)
8 Boards
(smallest position submitted)
01
02
03
04
05
06
07
08
09
10
11
12
Contact Gaps
LLCR-1
Forces - Mating / Unmating
25 Cycles
Forces - Mating / Unmating
25 Cycles (50 Total)
Forces - Mating / Unmating
25 Cycles (75 Total)
Forces - Mating / Unmating
25 Cycles (100 Total)
Forces - Mating / Unmating
Clean w/Compressed Air
Contact Gaps
Forces - Mating / Unmating
25 Cycles
Forces - Mating / Unmating
25 Cycles (50 Total)
Forces - Mating / Unmating
25 Cycles (75 Total)
Forces - Mating / Unmating
25 Cycles (100 Total)
Forces - Mating / Unmating
Contact Gaps
Forces - Mating / Unmating
25 Cycles
Forces - Mating / Unmating
25 Cycles (50 Total)
Forces - Mating / Unmating
25 Cycles (75 Total)
Forces - Mating / Unmating
25 Cycles (100 Total)
Forces - Mating / Unmating
13
Contact Gaps
14
LLCR-2
15
Thermal Shock
(Mated and Undisturbed)
16
LLCR-3
17
Cyclic Humidity
(Mated and Undisturbed)
18
19
LLCR-4
Forces - Mating / Unmating
Thermal Shock = EIA-364-32, Table II, Test Condition I:
-55oC to +85oC 1/2 hour dwell, 100 cycles
Humidity = EIA-364-31, Test Condition B (240 Hours)
and Method III (+25°C to +65°C @ 90% RH to 98% RH)
ambient pre-condition and delete steps 7a and 7b
Mating / Unmating Forces = EIA-364-13
Contact Gaps / Height - No standard method. Usually measured optically.
Gaps to be taken on a minimum of 20% of each part tested
LLCR = EIA-364-23, LLCR
20 mV Max, 100 mA Max
Use Keithley 580 or 3706 in 4 wire dry circuit mode
Page 6 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
FLOWCHARTS Continued
Thermal Aging
TEST
STEP
01
02
03
GROUP A1
8 Boards
Thermal Aging (Mated)
Contact Gaps
Forces - Mating / Unmating
LLCR-1
04
Thermal Aging
(Mated and Undisturbed)
05
06
07
LLCR-2
Forces - Mating / Unmating
Contact Gaps
Thermal Aging = EIA-364-17, Test Condition 4 (105°C)
Time Condition 'B' (250 Hours)
Mating / Unmating Forces = EIA-364-13
Contact Gaps / Height - No standard method. Usually measured optically.
Gaps to be taken on a minimum of 20% of each part tested
LLCR = EIA-364-23, LLCR
20 mV Max, 100 mA Max
Use Keithley 580 or 3706 in 4 wire dry circuit mode
Mechanical Shock / Vibration / LLCR
TEST
STEP
01
02
03
04
GROUP A1
192 Points
LLCR-1
Shock
Vibration
LLCR-2
Mechanical Shock = EIA 364-27 Half Sine,
100 g's, 6 milliSeconds (Condition "C") each axis
Vibration = EIA 364-28, Random Vibration
7.56 g RMS, Condition VB --- 2 hours/axis
LLCR = EIA-364-23, LLCR
20 mV Max, 100 mA Max
Use Keithley 580 or 3706 in 4 wire dry circuit mode
Page 7 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
FLOWCHARTS Continued
Shock / Vibration / nanoSecond Event Detection
TEST
STEP
GROUP A1
60 Points
01
Event Detection,
Shock
02
Event Detection,
Vibration
Mechanical Shock = EIA 364-27 Half Sine,
100 g's, 6 milliSeconds (Condition "C") each axis
Vibration = EIA 364-28, Random Vibration
7.56 g RMS, Condition VB --- 2 hours/axis
Event detection requirement during Shock / Vibration is 50 nanoseconds minimum
Normal Force
TEST
01
GROUP A1
Individual Contacts
(8-10 min)
Contact Gaps
GROUP A2
Individual Contacts
(8-10 min)
Contact Gaps
02
Setup Approved
Thermal Aging
(Mated and Undisturbed)
03
Normal Force
(in the body and soldered on PCB
unless otherwise specified)
Contact Gaps
STEP
04
Setup Approved
05
Normal Force
(in the body and soldered on PCB
unless otherwise specified)
Thermal Aging = EIA-364-17, Test Condition 4 (105°C)
Time Condition 'B' (250 Hours)
Normal Force = EIA-364-04
(Perpendicular) Displacement Force = 12.7 mm/min ± 6 mm/min
Spec is 50 N @ 1 mm displacement
Contact Gaps / Height - No standard method. Usually measured optically
Gaps to be taken on a minimum of 20% of each part tested
Page 8 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
ATTRIBUTE DEFINITIONS
The following is a brief, simplified description of attributes.
THERMAL SHOCK:
1)
2)
3)
4)
5)
6)
EIA-364-32, Thermal Shock (Temperature Cycling) Test Procedure for Electrical Connectors.
Test Condition 1: -55°C to +85°C
Test Time: ½ hour dwell at each temperature extreme
Number of Cycles: 100
All test samples are pre-conditioned at ambient.
All test samples are exposed to environmental stressing in the mated condition.
THERMAL:
1)
2)
3)
4)
5)
EIA-364-17, Temperature Life with or without Electrical Load Test Procedure for Electrical Connectors.
Test Condition 4 at 105° C.
Test Time Condition B for 250 hours.
All test samples are pre-conditioned at ambient.
All test samples are exposed to environmental stressing in the mated condition.
HUMIDITY:
1)
2)
3)
4)
5)
Reference document: EIA-364-31, Humidity Test Procedure for Electrical Connectors.
Test Condition B, 240 Hours.
Method III, +25° C to + 65° C, 90% to 98% Relative Humidity excluding sub-cycles 7a and 7b.
All samples are pre-conditioned at ambient.
All test samples are exposed to environmental stressing in the mated condition.
MECHANICAL SHOCK (Specified Pulse):
1)
2)
3)
4)
5)
6)
7)
Reference document: EIA-364-27, Mechanical Shock Test Procedure for Electrical Connectors
Test Condition C
Peak Value: 100 G
Duration: 6 Milliseconds
Wave Form: Half Sine
Velocity: 12.3 ft/s
Number of Shocks: 3 Shocks / Direction, 3 Axis (18 Total)
VIBRATION:
1)
2)
3)
4)
5)
6)
Reference document: EIA-364-28, Vibration Test Procedure for Electrical Connectors
Test Condition V, Letter B
Power Spectral Density: 0.04 G² / Hz
G ‘RMS’: 7.56
Frequency: 50 to 2000 Hz
Duration: 2.0 Hours per axis (3 axis total)
NANOSECOND-EVENT DETECTION:
1) Reference document: EIA-364-87, Nanosecond-Event Detection for Electrical Connectors
2) Prior to test, the samples were characterized to assure the low nanosecond event being monitored will trigger
the detector.
3) After characterization it was determined the test samples could be monitored for 50 nanosecond events
CONTACT GAPS:
1) Gaps above the surrounding plastic surface were measured before and after stressing the contacts (e.g.
thermal aging, mechanical cycling, etc.).
2) Typically, all contacts on the connector are measured.
Page 9 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
ATTRIBUTE DEFINITIONS
The following is a brief, simplified description of attributes.
MATING/UNMATING:
1) Reference document: EIA-364-13, Mating and Unmating Forces Test Procedure for Electrical Connectors.
2) The full insertion position was to within 0.003” to 0.004” of the plug bottoming out in the receptacle to
prevent damage to the system under test.
3) One of the mating parts is secured to a floating X-Y table to prevent damage during cycling.
NORMAL FORCE (FOR CONTACTS TESTED IN THE HOUSING):
1) Reference document: EIA-364-04, Normal Force Test Procedure for Electrical Connectors.
2) The contacts shall be tested in the connector housing.
3) If necessary, a “window” shall be made in the connector body to allow a probe to engage and deflect the
contact at the same attitude and distance (plus 0.05 mm [0.002”]) as would occur in actual use.
4) The connector housing shall be placed in a holding fixture that does not interfere with or otherwise influence
the contact force or deflection.
5) Said holding fixture shall be mounted on a floating, adjustable, X-Y table on the base of the Dillon TC2,
computer controlled test stand with a deflection measurement system accuracy of 5.0 µm (0.0002”).
6) The nominal deflection rate shall be 5 mm (0.2”)/minute.
7) Unless otherwise noted a minimum of five contacts shall be tested.
8) The force/deflection characteristic to load and unload each contact shall be repeated five times.
9) The system shall utilize the TC2 software in order to acquire and record the test data.
10) The permanent set of each contact shall be measured within the TC2 software.
11) The acquired data shall be graphed with the deflection data on the X-axis and the force data on the Y-axis
and a print out will be stored with the Tracking Code paperwork.
INSULATION RESISTANCE (IR):
To determine the resistance of insulation materials to leakage of current through or on the surface of these
materials when a DC potential is applied.
1) PROCEDURE:
a. Reference document: EIA-364-21, Insulation Resistance Test Procedure for Electrical Connectors.
b. Test Conditions:
i. Between Adjacent Contacts or Signal-to-Ground
ii. Electrification Time 2.0 minutes
iii. Test Voltage (500 VDC) corresponds to calibration settings for measuring resistances.
2) MEASUREMENTS:
3) When the specified test voltage is applied (VDC), the insulation resistance shall not be less than 5000
megohms.
Page 10 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
ATTRIBUTE DEFINITIONS
The following is a brief, simplified description of attributes.
DIELECTRIC WITHSTANDING VOLTAGE (DWV):
To determine if the sockets can operate at its rated voltage and withstand momentary over potentials due to
switching, surges, and other similar phenomenon. Separate samples are used to evaluate the effect of
environmental stresses so not to influence the readings from arcing that occurs during the measurement
process.
1) PROCEDURE:
a. Reference document: EIA-364-20, Withstanding Voltage Test Procedure for Electrical Connectors.
b. Test Conditions:
i. Between Adjacent Contacts or Signal-to-Ground
ii. Rate of Application 500 V/Sec
iii. Test Voltage (VAC) until breakdown occurs
2) MEASUREMENTS/CALCULATIONS
a. The breakdown voltage shall be measured and recorded.
b. The dielectric withstanding voltage shall be recorded as 75% of the minimum breakdown voltage.
c. The working voltage shall be recorded as one-third (1/3) of the dielectric withstanding voltage (onefourth of the breakdown voltage)..
LLCR:
1) EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
2) A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
3) The following guidelines are used to categorize the changes in LLCR as a result from stressing
a. <= +5.0 mOhms: ----------------------------- Stable
b. +5.1 to +10.0 mOhms: ---------------------- Minor
c. +10.1 to +15.0 mOhms: -------------------- Acceptable
d. +15.1 to +50.0 mOhms: -------------------- Marginal
e. +50.1 to +2000 mOhms: ------------------- Unstable
f. >+2000 mOhms: ----------------------------- Open Failure
Page 11 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
ATTRIBUTE DEFINITIONS
The following is a brief, simplified description of attributes.
GAS TIGHT:
1)
2)
3)
4)
To provide method for evaluating the ability of the contacting surfaces in preventing penetration of harsh
vapors which might lead to oxide formation that may degrade the electrical performance of the contact
system.
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing
a. <= +5.0 mOhms: ----------------------------- Stable
b. +5.1 to +10.0 mOhms: ---------------------- Minor
c. +10.1 to +15.0 mOhms: -------------------- Acceptable
d. +15.1 to +50.0 mOhms: -------------------- Marginal
e. +50.1 to +2000 mOhms: ------------------- Unstable
f. >+2000 mOhms: ----------------------------- Open Failure
Procedure:
a. Reference document: EIA-364-36, Test Procedure for Determination of Gas-Tight Characteristics
for Electrical Connectors, Sockets and/or Contact Systems.
b. Test Conditions:
i. Class II--- Mated pairs of contacts assembled to their plastic housings.
ii. Reagent grade Nitric Acid shall be used of sufficient volume to saturate the test chamber
iii. The ratio of the volume of the test chamber to the surface area of the acid shall be 10:1.
iv. The chamber shall be saturated with the vapor for at least 15 minutes before samples are
added.
v. Exposure time, 55 to 65 minutes.
vi. The samples shall be no closer to the chamber walls than 1 inches and no closer to the
surface of the acid than 3 inches.
vii. The samples shall be dried after exposure for a minimum of 1 hour.
о
viii. Drying temperature 50 C
ix. The final LLCR shall be conducted within 1 hour after drying.
Page 12 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
RESULTS
Contact Gaps
Thermal aging
 Initial
o Min -------------------------------------------------- 0.0127 Inch
o Max ------------------------------------------------- 0.0139 Inch
 After thermal aging
o Min -------------------------------------------------- 0.0128 Inch
o Max ------------------------------------------------- 0.0144 Inch
Mating&Unmating durability
 Initial
o Min -------------------------------------------------- 0.0125 Inch
o Max ------------------------------------------------- 0.0141 Inch
 After 100 Cycles
o Min -------------------------------------------------- 0.0125 Inch
o Max ------------------------------------------------- 0.0141 Inch
Mating – Unmating force
Thermal aging (SFM-150-02-S-D-A/TFM-150-02-S-D-A):
 Initial
o Mating
 Min --------------------------------------16.70 Lbs
 Max--------------------------------------20.58 Lbs
o Unmating
 Min --------------------------------------14.67 Lbs
 Max--------------------------------------19.14 Lbs
 After thermal aging
o Mating
 Min --------------------------------------13.01 Lbs
 Max--------------------------------------20.60 Lbs
o Unmating
 Min --------------------------------------- 9.06 Lbs
 Max--------------------------------------13.75 Lbs
Page 13 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
RESULTS Continued
Mating&Unmating durability (SFM-150-02-S-D-A/TFM-150-02-S-D-A):
 Initial
o Mating
 Min --------------------------------------15.35 Lbs
 Max--------------------------------------18.80 Lbs
o Unmating
 Min --------------------------------------12.39 Lbs
 Max--------------------------------------17.50 Lbs
 After 25 Cycles
o Mating
 Min --------------------------------------17.03 Lbs
 Max--------------------------------------20.65 Lbs
o Unmating
 Min --------------------------------------15.00 Lbs
 Max--------------------------------------18.63 Lbs
 After 50 Cycles
o Mating
 Min --------------------------------------17.73 Lbs
 Max--------------------------------------21.98 Lbs
o Unmating
 Min --------------------------------------15.95 Lbs
 Max--------------------------------------19.97 Lbs
 After 75 Cycles
o Mating
 Min --------------------------------------18.34 Lbs
 Max--------------------------------------22.80 Lbs
o Unmating
 Min --------------------------------------16.78 Lbs
 Max--------------------------------------20.40 Lbs
 After 100 Cycles
o Mating
 Min --------------------------------------19.07 Lbs
 Max--------------------------------------24.14 Lbs
o Unmating
 Min --------------------------------------17.16 Lbs
 Max--------------------------------------21.37 Lbs
 After Humidity
o Mating
 Min --------------------------------------14.57 Lbs
 Max--------------------------------------18.22 Lbs
o Unmating
 Min --------------------------------------13.50 Lbs
 Max--------------------------------------17.08 Lbs
Page 14 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
RESULTS Continued
Mating&Unmating basic (SFM-125-02-S-D-A/TFM-125-02-S-D-A):
 Initial
o Mating
 Min --------------------------------------10.66 Lbs
 Max--------------------------------------14.29 Lbs
o Unmating
 Min --------------------------------------- 9.33 Lbs
 Max--------------------------------------11.61 Lbs
 After 25 Cycles
o Mating
 Min --------------------------------------10.14 Lbs
 Max--------------------------------------12.19 Lbs
o Unmating
 Min --------------------------------------- 9.34 Lbs
 Max--------------------------------------10.57 Lbs
 After 50 Cycles
o Mating
 Min --------------------------------------11.52 Lbs
 Max--------------------------------------13.80 Lbs
o Unmating
 Min --------------------------------------10.15 Lbs
 Max--------------------------------------12.18 Lbs
 After 75 Cycles
o Mating
 Min --------------------------------------12.03 Lbs
 Max--------------------------------------15.11 Lbs
o Unmating
 Min --------------------------------------10.83 Lbs
 Max--------------------------------------13.60 Lbs
 After 100 Cycles
o Mating
 Min --------------------------------------12.18 Lbs
 Max--------------------------------------16.26 Lbs
o Unmating
 Min --------------------------------------11.49 Lbs
 Max--------------------------------------14.33 Lbs
Page 15 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
RESULTS Continued
Mating&Unmating basic (SFM-105-02-S-D-A/TFM-105-02-S-D-A):
 Initial
o Mating
 Min --------------------------------------- 1.11 Lbs
 Max--------------------------------------- 1.74 Lbs
o Unmating
 Min --------------------------------------- 1.02 Lbs
 Max--------------------------------------- 1.48 Lbs
 After 25 Cycles
o Mating
 Min --------------------------------------- 1.12 Lbs
 Max--------------------------------------- 1.72 Lbs
o Unmating
 Min --------------------------------------- 0.99 Lbs
 Max--------------------------------------- 1.47 Lbs
 After 50 Cycles
o Mating
 Min --------------------------------------- 1.15 Lbs
 Max--------------------------------------- 1.85 Lbs
o Unmating
 Min --------------------------------------- 1.03 Lbs
 Max--------------------------------------- 1.59 Lbs
 After 75 Cycles
o Mating
 Min --------------------------------------- 1.19 Lbs
 Max--------------------------------------- 1.83 Lbs
o Unmating
 Min --------------------------------------- 1.01 Lbs
 Max--------------------------------------- 1.64 Lbs
 After 100 Cycles
o Mating
 Min --------------------------------------- 1.17 Lbs
 Max--------------------------------------- 1.94 Lbs
o Unmating
 Min --------------------------------------- 1.01 Lbs
 Max--------------------------------------- 1.76 Lbs
Page 16 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
RESULTS Continued
Normal Force at 0.005 inch deflection
 Initial
Back beam
o Min ----------------------------------------------- 100.40 gf
o Max --------------------------------------------- 133.00 gf
Left and right beam
o Min -------------------------------------------------99.90 gf
o Max --------------------------------------------- 123.00 gf

Thermal
Back beam
o Min -------------------------------------------------80.80 gf
o Max ---------------------------------------------- 139.10 gf
Left and right beam
o Min -------------------------------------------------74.00 gf
o Max ---------------------------------------------- 119.50 gf
Set ----- 0.0002 Inch
Set ----- 0.0009 Inch
Set ----- 0.0008 Inch
Set ----- 0.0023 Inch
Set ----- 0.0007 Inch
Set ----- 0.0012 Inch
Set ----- 0.0011 Inch
Set ----- 0.0016 Inch
LLCR Durability (192 pin LLCR test points)
 Initial ----------------------------------------------------------------- 7.7 mOhms Max
 After 100 Cycles
o <= +5.0 mOhms ---------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
 After thermal shock
o <= +5.0 mOhms ---------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
 After humidity
o <= +5.0 mOhms ---------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
Page 17 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
RESULTS Continued
LLCR Thermal aging (192 pin LLCR test points)
 Initial ----------------------------------------------------------------- 7.6 mOhms Max
 Thermal aging
o <= +5.0 mOhms ---------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
LLCR Gas Tight (192 pin LLCR test points)
 Initial ----------------------------------------------------------------- 8.2 mOhms Max
 Gas-Tight
o <= +5.0 mOhms ---------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
LLCR Mechanical shock&Vibration (192 pin LLCR test points)
 Initial ----------------------------------------------------------------- 8.0 mOhms Max
 Shock&Vibration
o <= +5.0 mOhms ---------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
Insulation Resistance minimums, IR
Pin-Pin
 Initial
o Mated ---------------------------------------------- 100000Meg Ω ------------------------- Pass
o Unmated ------------------------------------------ 100000Meg Ω ------------------------ Pass
 Thermal
o Mated ---------------------------------------------- 100000Meg Ω ------------------------ Pass
o Unmated ------------------------------------------ 100000Meg Ω ------------------------ Pass
 Humidity
o Mated ---------------------------------------------- 100000Meg Ω ------------------------ Pass
o Unmated ------------------------------------------ 100000Meg Ω ------------------------ Pass
Dielectric Withstanding Voltage minimums, DWV
 Minimums
o Breakdown Voltage -------------------------------- 1000VAC
o Test Voltage ------------------------------------------- 750VAC
o Working Voltage ------------------------------------- 250VAC
Pin - pin
 Initial DWV -------------------------------------------------- Passed
 Thermal DWV ----------------------------------------------- Passed
 Humidity DWV ---------------------------------------------- Passed
Page 18 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA SUMMARIES
CONTACT GAPS:
Mating&Unmating durability:
Initial
Units:
Minimum
Maximum
Average
St. Dev.
Count
inches
0.0125
0.0141
0.0132
0.0003
160
After 100 Cycles
Units:
inches
Minimum
0.0125
Maximum
0.0141
Average
0.0132
St. Dev.
0.0003
Count
160
inches
0.0127
0.0139
0.0132
0.0003
160
After Thermal
Units:
inches
Minimum
0.0128
Maximum
0.0144
Average
0.0135
St. Dev.
0.0004
Count
160
Thermal aging:
Initial
Units:
Minimum
Maximum
Average
St. Dev.
Count
MATING/UNMATING FORCE:
Mating/Unmating durability (SFM-150-02-S-D-A/TFM-150-02-S-D-A):
Initial
25 Cycles
Mating
Minimum
Maximum
Average
St Dev
Count
Unmating
Mating
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
68.29
83.62
75.09
5.93
8
15.35
18.80
16.88
1.33
8
55.10
77.84
67.65
6.99
8
12.39
17.50
15.21
1.57
8
75.74
91.86
86.36
5.18
8
17.03
20.65
19.42
1.16
8
66.72
82.85
76.55
5.54
8
15.00
18.63
17.21
1.25
8
50 Cycles
Mating
Minimum
Maximum
Average
St Dev
Count
75 Cycles
Unmating
Mating
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
78.87
97.78
92.23
6.37
8
17.73
21.98
20.73
1.43
8
70.95
88.83
81.74
6.89
8
15.95
19.97
18.38
1.55
8
81.57
101.41
95.51
6.37
8
18.34
22.80
21.47
1.43
8
74.62
90.98
84.12
6.55
8
16.78
20.46
18.91
1.47
8
100 Cycles
Maximum
Average
St Dev
Count
Unmating
Newtons
Mating
Minimum
Unmating
Newtons
After Humidity
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
84.82
107.39
99.00
6.94
8
19.07
24.14
22.26
1.56
8
76.33
95.07
86.76
7.31
8
17.16
21.37
19.50
1.64
8
64.80
81.02
76.40
5.12
8
14.57
18.22
17.18
1.15
8
60.06
75.97
70.27
4.78
8
13.50
17.08
15.80
1.07
8
Page 19 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA SUMMARIES
Thermal aging (SFM-150-02-S-D-A/TFM-150-02-S-D-A):
Initial
After Thermals
Mating
Minimum
Maximum
Average
S t Dev
Count
Unmating
Mating
Unm ating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
74.28
91.52
83.19
16.70
20.58
18.70
65.27
85.15
74.95
14.67
19.14
16.85
57.88
91.63
66.63
13.01
20.60
14.98
40.28
61.16
55.86
9.06
13.75
12.56
6.11
8
1.37
8
7.28
8
1.64
8
10.48
8
2.36
8
6.82
8
1.53
8
Mating/Unmating basic (SFM-125-02-S-D-A/TFM-125-02-S-D-A):
Initial
After 25 Cycles
Mating
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
47.42
10.66
41.50
9.33
45.10
10.14
41.54
9.34
Maximum
63.56
14.29
51.64
11.61
54.22
12.19
47.02
10.57
Average
53.79
12.09
48.12
10.82
49.94
11.23
43.79
9.84
St Dev
5.52
1.24
3.52
0.79
3.33
0.75
2.08
0.47
Count
8
8
8
8
8
8
8
8
After 50 Cycles
Mating
After 75 Cycles
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
51.24
11.52
45.15
10.15
53.51
12.03
48.17
10.83
Maximum
61.38
13.80
54.18
12.18
67.21
15.11
60.49
13.60
Average
56.20
12.64
49.45
11.12
61.56
13.84
54.75
12.31
St Dev
4.44
1.00
3.59
0.81
5.12
1.15
4.55
1.02
Count
8
8
8
8
8
8
8
8
After 100 Cycles
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
54.18
12.18
51.11
11.49
Maximum
72.32
16.26
63.74
14.33
Average
64.35
14.47
58.76
13.21
St Dev
6.09
1.37
5.00
1.12
Count
8
8
8
8
Page 20 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA SUMMARIES
Mating/Unmating basic (SFM-105-02-S-D-A/TFM-105-02-S-D-A):
Initial
25 Cycles
Mating
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
4.94
1.11
4.54
1.02
4.98
1.12
4.40
0.99
Maximum
7.74
1.74
6.58
1.48
7.65
1.72
6.54
1.47
Average
6.15
1.38
5.53
1.24
6.03
1.36
5.43
1.22
St Dev
0.83
0.19
0.71
0.16
0.95
0.21
0.80
0.18
Count
8
8
8
8
8
8
8
8
50 Cycles
Mating
75 Cycles
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
5.12
1.15
4.58
1.03
5.29
1.19
4.49
1.01
Maximum
8.23
1.85
7.07
1.59
8.14
1.83
7.29
1.64
Average
6.27
1.41
5.61
1.26
6.44
1.45
5.78
1.30
St Dev
1.14
0.26
0.98
0.22
1.28
0.29
1.15
0.26
Count
8
8
8
8
8
8
8
8
100 Cycles
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
5.20
1.17
4.49
1.01
Maximum
8.63
1.94
7.83
1.76
Average
6.71
1.51
5.97
1.34
St Dev
1.44
0.32
1.22
0.28
Count
8
8
8
8
Page 21 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA SUMMARIES
Mating/Unmating Data for 5, 25 and 50 Position SFM/TFM
Mating (Initial)
Unmating (Initial)
Mating (100 Cycles)
Unmating (100 Cycles)
25.00
20.00
Force (lbs)
15.00
10.00
5.00
0.00
5 Pos.
25 Pos.
Number of Terminals per Row
Page 22 of 52
50 Pos.
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA SUMMARIES
Normal force
Initial (back beam)
Initial
Averages
Min
Max
St. Dev
Count
0.0005
10.78
8.90
14.10
2.300
4
0.0010
22.08
18.10
27.30
4.112
4
Deflections in inches Forces in Grams
0.0015 0.0020 0.0025 0.0030 0.0035 0.0040
34.88 47.68 59.60
71.83 83.60 95.05
27.70 36.90 45.70
54.60 63.70 72.70
41.10 55.40 68.10
82.50 96.10 109.40
5.552 7.839 9.967 12.356 14.464 16.566
4
4
4
4
4
4
0.0045
107.50
85.20
122.90
17.051
4
0.0050
119.25
100.40
133.00
15.296
4
SET
0.0005
0.0002
0.0009
0.0003
4
Initial (left and right beam)
Initial
Averages
Min
Max
St. Dev
Count
0.0005
13.60
11.10
15.40
1.706
7
0.0010
26.01
21.00
30.00
3.479
7
0.0015
37.93
31.40
43.50
4.610
7
Deflections in inches Forces in Grams
0.0020 0.0025 0.0030 0.0035 0.0040
49.77
61.67
72.60
83.31
93.73
43.30
54.20
65.20
74.80
83.30
56.50
69.50
80.50
91.70
103.70
4.762
5.149
5.542
5.944
6.871
7
7
7
7
7
0.0045
103.26
91.60
114.50
7.766
7
0.0050
112.19
99.90
123.00
7.913
7
SET
0.0013
0.0008
0.0023
0.0005
7
0.0015
34.94
22.40
47.30
11.156
5
Deflections in inches Forces in Grams
0.0020 0.0025 0.0030 0.0035 0.0040
45.62
56.20
66.90
77.50
87.54
28.90
35.60
43.00
51.80
59.80
61.80
76.40
90.40 104.30 116.90
15.078 18.655 21.865 24.303 26.886
5
5
5
5
5
0.0045
98.56
73.20
128.80
27.218
5
0.0050
108.02
80.80
139.10
27.440
5
SET
0.0010
0.0007
0.0012
0.0002
5
After thermal (back beam)
After
Thermals 0.0005
Averages 12.26
Min 7.90
Max 17.30
St. Dev 4.038
Count
5
0.0010
23.88
15.10
32.50
7.967
5
After thermal (left and right beam)
After
Thermals 0.0005
Averages 10.46
Min 9.50
Max 12.60
St. Dev 1.118
Count
7
0.0010
20.39
17.90
23.20
1.807
7
0.0015
30.37
25.30
34.20
3.488
7
Deflections in inches Forces in Grams
0.0020 0.0025 0.0030 0.0035 0.0040
41.57
52.43
63.34
73.16
82.17
34.80
42.20
48.80
55.80
62.10
50.90
64.10
75.50
86.40
98.40
5.473
7.203
9.477
11.475 13.297
7
7
7
7
7
Page 22 of 51
0.0045
90.93
68.10
110.20
15.030
7
0.0050
98.81
74.00
119.50
15.989
7
SET
0.0013
0.0011
0.0016
0.0002
7
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA SUMMARIES
INSULATION RESISTANCE (IR):
Pin to Pin
Minimum
Initial
Thermal
Humidity
Mated
SFM/TFM
100000
100000
100000
Unmated
SFM
100000
100000
100000
DIELECTRIC WITHSTANDING VOLTAGE (DWV):
Voltage Rating Summary
Minimum
SFM/TFM
1000
750
250
Break Down Voltage
Test Voltage
Working Voltage
Pin to Pin
Initial Test Voltage
After Thermal Test Voltage
After Humidity Test Voltage
Page 23 of 51
Passed
Passed
Passed
Unmated
TFM
100000
100000
100000
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA SUMMARIES
LLCR Durability:
1)
2)
3)
4)
A total of 192 points were measured.
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
a. <= +5.0 mOhms: ----------------------------- Stable
b. +5.1 to +10.0 mOhms: ---------------------- Minor
c. +10.1 to +15.0 mOhms: -------------------- Acceptable
d. +15.1 to +50.0 mOhms: -------------------- Marginal
e. +50.1 to +2000 mOhms -------------------- Unstable
f. >+2000 mOhms: ----------------------------- Open Failure
Date
Room Temp C
RH
Name
mOhm values
Average
St. Dev.
Min
Max
Count
3/23/2011
22
42%
Aaron McKim
Actual
Initial
6.8
0.4
6.0
7.7
192
3/28/2011
23
27%
Aaron McKim
Delta
100 Cycles
0.2
0.2
-0.2
1.0
192
4/4/2011
23
48%
Aaron McKim
Delta
Thermal
0.6
1.0
-0.4
3.3
192
How many samples are being tested?
How many contacts are on each
board?
100 Cycles
Thermal
Humidity
Stable
192
192
192
Minor
0
0
0
Acceptable
0
0
0
Page 24 of 51
Marginal
0
0
0
4/18/2011
23
34%
Aaron McKim
Delta
Humidity
0.6
1.0
-0.5
3.5
192
8
24
Unstable
0
0
0
Open
0
0
0
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA SUMMARIES
LLCR Thermal aging:
1)
2)
3)
4)
A total of 192 points were measured.
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
a. <= +5.0 mOhms: ----------------------------- Stable
b. +5.1 to +10.0 mOhms: ---------------------- Minor
c. +10.1 to +15.0 mOhms: -------------------- Acceptable
d. +15.1 to +50.0 mOhms: -------------------- Marginal
e. +50.1 to +2000 mOhms -------------------- Unstable
f. >+2000 mOhms: ----------------------------- Open Failure
Date
Room Temp C
RH
Name
mOhm values
Average
St. Dev.
Min
Max
Count
3/23/2011
22
45%
Aaron McKim
Actual
Initial
6.9
0.3
6.2
7.6
192
4/4/2011
23
48%
Aaron McKim
Delta
Thermal Age
0.0
0.1
-0.3
0.7
192
8
24
How many samples are being tested?
How many contacts are on each board?
Thermal Age
Stable
192
Minor
0
Acceptable
0
Page 25 of 51
Marginal
0
Unstable
0
Open
0
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA SUMMARIES
LLCR Shock/Vibration:
1)
2)
3)
4)
A total of 192 points were measured.
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
a. <= +5.0 mOhms: ----------------------------- Stable
b. +5.1 to +10.0 mOhms: ---------------------- Minor
c. +10.1 to +15.0 mOhms: -------------------- Acceptable
d. +15.1 to +50.0 mOhms: -------------------- Marginal
e. +50.1 to +2000 mOhms -------------------- Unstable
f. >+2000 mOhms: ----------------------------- Open Failure
Date
Room Temp C
RH
Name
mOhm values
Average
St. Dev.
Min
Max
Count
3/23/2011
23
43%
Aaron McKim
Actual
Initial
6.7
0.4
6.0
8.2
192
3/25/2011
23
27%
Aaron McKim
Delta
Shock / Vibe
0.1
0.5
-0.8
3.3
192
How many samples are being tested?
How many contacts are on each board?
Shock / Vibe
Stable
192
Minor
0
Acceptable
0
Page 26 of 51
Marginal
0
8
24
Unstable
0
Open
0
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA SUMMARIES
GAS TIGHT:
1)
2)
3)
4)
A total of 192 points were measured.
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
a. <= +5.0 mOhms: ----------------------------- Stable
b. +5.1 to +10.0 mOhms: ---------------------- Minor
c. +10.1 to +15.0 mOhms: -------------------- Acceptable
d. +15.1 to +50.0 mOhms: -------------------- Marginal
e. +50.1 to +2000 mOhms: ------------------- Unstable
f. >+2000 mOhms: ----------------------------- Open Failure
Date
Room Temp C
RH
Name
mOhm values
Average
St. Dev.
Min
Max
Count
3/21/2011
22
48%
Aaron McKim
Actual
Initial
6.7
0.5
5.6
8.0
192
3/22/2011
23
44%
Aaron McKim
Delta
Gas Tight
0.1
0.1
-0.1
0.8
192
How many samples are being tested?
How many contacts are on each board?
Gas Tight
Stable
192
Minor
0
Acceptable
0
Page 27 of 51
Marginal
0
8
24
Unstable
0
Open
0
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA
CONTACT GAPS
Thermal aging
Pos.#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Pos.#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Initial
Units:
B1
0.0132
0.0132
0.0134
0.0130
0.0132
0.0132
0.0133
0.0128
0.0132
0.0128
0.0133
0.0130
0.0130
0.0130
0.0134
0.0129
0.0132
0.0130
0.0131
0.0129
Initial
Units:
B1
0.0134
0.0135
0.0136
0.0129
0.0132
0.0136
0.0134
0.0139
0.0134
0.0135
0.0131
0.0136
0.0132
0.0138
0.0130
0.0141
0.0133
0.0134
0.0134
0.0136
inches
B2
0.0127
0.0134
0.0136
0.0137
0.0135
0.0134
0.0136
0.0138
0.0133
0.0136
0.0131
0.0139
0.0134
0.0133
0.0136
0.0137
0.0138
0.0136
0.0139
0.0138
B3
0.0133
0.0132
0.0131
0.0132
0.0134
0.0133
0.0132
0.0131
0.0134
0.0133
0.0130
0.0132
0.0133
0.0136
0.0130
0.0130
0.0132
0.0129
0.0130
0.0129
B4
0.0127
0.0132
0.0132
0.0129
0.0132
0.0133
0.0133
0.0131
0.0132
0.0135
0.0129
0.0132
0.0136
0.0137
0.0133
0.0128
0.0135
0.0133
0.0133
0.0131
B5
0.0131
0.0130
0.0135
0.0130
0.0131
0.0131
0.0128
0.0130
0.0133
0.0131
0.0130
0.0129
0.0136
0.0132
0.0130
0.0127
0.0129
0.0136
0.0129
0.0129
B6
0.0130
0.0128
0.0130
0.0132
0.0130
0.0131
0.0134
0.0131
0.0131
0.0132
0.0130
0.0132
0.0130
0.0129
0.0130
0.0131
0.0130
0.0129
0.0131
0.0133
B7
0.0132
0.0133
0.0132
0.0128
0.0134
0.0128
0.0131
0.0128
0.0131
0.0128
0.0129
0.0129
0.0130
0.0130
0.0130
0.0129
0.0130
0.0130
0.0130
0.0128
B8
0.0133
0.0131
0.0132
0.0131
0.0132
0.0131
0.0132
0.0133
0.0132
0.0132
0.0131
0.0131
0.0132
0.0131
0.0133
0.0129
0.0134
0.0133
0.0130
0.0130
inches
B2
0.0128
0.0133
0.0139
0.0141
0.0137
0.0134
0.0138
0.0144
0.0140
0.0142
0.0133
0.0144
0.0141
0.0143
0.0134
0.0136
0.0136
0.0137
0.0135
0.0138
B3
0.0132
0.0138
0.0131
0.0134
0.0129
0.0140
0.0135
0.0135
0.0136
0.0143
0.0132
0.0137
0.0137
0.0144
0.0132
0.0133
0.0136
0.0141
0.0131
0.0135
B4
0.0128
0.0134
0.0131
0.0135
0.0136
0.0135
0.0135
0.0136
0.0137
0.0139
0.0132
0.0132
0.0140
0.0143
0.0136
0.0133
0.0134
0.0136
0.0133
0.0134
B5
0.0132
0.0130
0.0133
0.0131
0.0131
0.0132
0.0129
0.0134
0.0133
0.0142
0.0129
0.0136
0.0138
0.0144
0.0132
0.0137
0.0133
0.0136
0.0132
0.0130
B6
0.0130
0.0133
0.0133
0.0139
0.0134
0.0130
0.0140
0.0141
0.0135
0.0139
0.0135
0.0135
0.0136
0.0139
0.0132
0.0134
0.0131
0.0132
0.0134
0.0134
B7
0.0133
0.0137
0.0132
0.0136
0.0133
0.0135
0.0133
0.0137
0.0137
0.0137
0.0137
0.0140
0.0137
0.0139
0.0130
0.0133
0.0132
0.0133
0.0132
0.0134
B8
0.0130
0.0139
0.0133
0.0136
0.0137
0.0137
0.0135
0.0136
0.0133
0.0136
0.0138
0.0133
0.0137
0.0140
0.0134
0.0131
0.0136
0.0144
0.0136
0.0130
Page 28 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA Continued
Mating&Unmating durability
Pos.#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Pos.#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Initial
Units:
B1
0.0135
0.0138
0.0136
0.0141
0.0138
0.0132
0.0125
0.0132
0.0132
0.0128
0.0126
0.0135
0.0127
0.0129
0.0133
0.0137
0.0138
0.0139
0.0134
0.0139
Initial
Units:
B1
0.0137
0.0135
0.0135
0.0134
0.0138
0.0132
0.0135
0.0140
0.0138
0.0134
0.0135
0.0141
0.0137
0.0135
0.0131
0.0135
0.0136
0.0134
0.0131
0.0131
inches
B2
0.0131
0.0136
0.0130
0.0133
0.0135
0.0134
0.0130
0.0127
0.0132
0.0130
0.0126
0.0128
0.0129
0.0131
0.0132
0.0135
0.0133
0.0131
0.0134
0.0133
B3
0.0136
0.0137
0.0133
0.0133
0.0132
0.0136
0.0131
0.0134
0.0131
0.0130
0.0129
0.0135
0.0129
0.0136
0.0137
0.0135
0.0134
0.0131
0.0129
0.0134
B4
0.0132
0.0129
0.0133
0.0132
0.0131
0.0128
0.0130
0.0133
0.0132
0.0134
0.0130
0.0132
0.0129
0.0132
0.0138
0.0131
0.0134
0.0134
0.0133
0.0130
B5
0.0133
0.0135
0.0129
0.0131
0.0134
0.0135
0.0133
0.0131
0.0129
0.0133
0.0128
0.0131
0.0129
0.0132
0.0130
0.0133
0.0129
0.0132
0.0131
0.0131
B6
0.0135
0.0134
0.0134
0.0138
0.0131
0.0137
0.0134
0.0136
0.0134
0.0133
0.0131
0.0135
0.0131
0.0132
0.0136
0.0131
0.0135
0.0134
0.0135
0.0130
B7
0.0129
0.0132
0.0131
0.0134
0.0128
0.0134
0.0133
0.0130
0.0130
0.0129
0.0133
0.0128
0.0127
0.0131
0.0134
0.0135
0.0127
0.0132
0.0135
0.0135
B8
0.0131
0.0132
0.0138
0.0131
0.0133
0.0134
0.0136
0.0131
0.0136
0.0134
0.0132
0.0132
0.0130
0.0133
0.0130
0.0131
0.0130
0.0134
0.0133
0.0135
inches
B2
0.0134
0.0131
0.0130
0.0131
0.0134
0.0129
0.0132
0.0129
0.0131
0.0130
0.0129
0.0129
0.0132
0.0130
0.0132
0.0130
0.0133
0.0130
0.0131
0.0131
B3
0.0133
0.0132
0.0132
0.0134
0.0128
0.0134
0.0133
0.0131
0.0133
0.0131
0.0134
0.0133
0.0132
0.0131
0.0131
0.0136
0.0133
0.0130
0.0128
0.0133
B4
0.0134
0.0132
0.0134
0.0132
0.0133
0.0130
0.0131
0.0130
0.0131
0.0133
0.0130
0.0129
0.0129
0.0128
0.0131
0.0131
0.0130
0.0134
0.0131
0.0133
B5
0.0131
0.0136
0.0132
0.0135
0.0131
0.0133
0.0138
0.0129
0.0132
0.0132
0.0128
0.0128
0.0128
0.0131
0.0133
0.0130
0.0131
0.0132
0.0132
0.0132
B6
0.0135
0.0132
0.0133
0.0132
0.0131
0.0132
0.0133
0.0130
0.0135
0.0132
0.0130
0.0132
0.0132
0.0126
0.0137
0.0132
0.0131
0.0128
0.0133
0.0130
B7
0.0127
0.0129
0.0130
0.0132
0.0127
0.0128
0.0131
0.0127
0.0127
0.0126
0.0130
0.0127
0.0127
0.0125
0.0132
0.0130
0.0129
0.0128
0.0130
0.0130
B8
0.0134
0.0131
0.0139
0.0131
0.0132
0.0132
0.0132
0.0128
0.0133
0.0129
0.0131
0.0131
0.0131
0.0130
0.0130
0.0134
0.0130
0.0127
0.0130
0.0130
Page 29 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA Continued
MATING/UNMATING FORCE
Mating/Unmating durability:
Initial
25 Cycles
50 Cycles
75 Cycles
100 Cycles
After Humidity
Sample#
1
Mating
Unmating
Mating
Unmating
Mating
Unmating
Mating
Unmating
Mating
Unmating
Mating
Unmating
15.35
12.39
17.03
15.00
17.73
15.95
18.34
16.78
19.07
17.16
14.57
13.50
2
3
4
5
6
7
8
15.64
16.76
17.25
15.45
17.36
18.45
18.80
14.28
15.71
15.16
14.76
15.03
16.85
17.50
20.28
20.07
19.48
19.16
18.63
20.65
20.03
17.35
18.37
16.57
17.45
16.12
18.63
18.18
21.64
21.74
19.98
21.28
20.02
21.98
21.50
18.68
19.65
17.19
19.38
16.67
19.97
19.53
21.84
22.52
21.10
22.11
20.83
22.80
22.24
18.47
20.37
17.60
19.96
17.59
20.46
20.08
22.69
22.60
21.92
23.01
21.24
24.14
23.38
19.50
20.30
18.30
20.96
17.55
21.37
20.89
17.72
18.22
17.53
17.57
17.00
18.00
16.81
15.49
16.02
15.81
16.79
15.74
17.08
15.96
Thermal Aging:
Initial
After Thermals
Sample#
1
Mating
Unmating
Mating
Unmating
18.56
16.20
13.01
12.05
2
3
4
5
6
7
8
17.36
17.74
16.70
19.83
20.58
19.98
18.87
15.52
14.67
15.71
18.82
19.14
18.03
16.72
14.16
14.05
13.72
14.93
14.47
14.89
20.60
13.16
12.75
12.54
13.75
13.41
13.74
9.06
Page 30 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA Continued
NORMAL FORCE
Initial (Back beam)
Initial
Sample # 0.0005
1
8.9
2
10.4
3
9.7
4
14.1
Deflections in inches, Forces in Grams
0.0015 0.0020 0.0025 0.0030 0.0035 0.0040
27.7
36.9
45.7
54.6
63.7
72.7
34.4
47.8
59.3
71.5
82.4
92.5
36.3
50.6
65.3
78.7
92.2
105.6
41.1
55.4
68.1
82.5
96.1
109.4
0.0010
18.1
19.6
23.3
27.3
0.0045
85.2
103.4
118.5
122.9
0.0050
100.4
113.3
130.3
133.0
SET
0.0006
0.0009
0.0002
0.0002
0.0050
112.2
99.9
105.4
119.6
123.0
114.4
110.8
SET
0.0023
0.0012
0.0008
0.0010
0.0011
0.0012
0.0012
Initial (Left and right beam)
Initial
Sample # 0.0005
1
14.0
3
13.2
4
11.1
5
11.6
6
15.0
8
14.9
9
15.4
0.0010
27.7
24.7
21.0
22.0
30.0
28.4
28.3
0.0015
40.1
35.8
31.4
32.8
43.5
41.1
40.8
Deflections in inches, Forces in Grams
0.0020 0.0025 0.0030 0.0035 0.0040
51.4
62.7
73.3
83.4
93.8
46.4
55.9
65.4
74.8
83.3
43.3
54.2
65.2
76.6
87.2
45.5
62.3
75.6
87.6
99.1
56.5
69.5
80.5
91.7
103.7
52.8
63.8
74.9
85.7
95.6
52.5
63.3
73.3
83.4
93.4
0.0045
102.4
91.6
96.7
110.2
114.5
105.6
101.8
After thermal (Back beam)
After Thermals
Sample # 0.0005
1
17.3
2
15.4
3
9.0
4
11.7
5
7.9
0.0010
32.5
31.7
17.6
22.5
15.1
0.0015
47.3
45.6
26.6
32.8
22.4
Deflections in inches, Forces in Grams
0.0020 0.0025 0.0030 0.0035 0.0040
61.8
76.4
90.4
104.3
116.9
60.8
75.0
89.1
101.7
114.7
34.4
42.7
50.6
58.6
65.8
42.2
51.3
61.4
71.1
80.5
28.9
35.6
43.0
51.8
59.8
0.0045
128.8
126.4
73.2
89.1
75.3
0.0050
139.1
135.6
80.8
97.3
87.3
SET
0.0009
0.0009
0.0007
0.0012
0.0012
Deflections in inches, Forces in Grams
0.0020 0.0025 0.0030 0.0035 0.0040
37.0
46.1
55.6
64.6
72.4
50.9
64.1
75.5
86.4
97.0
46.2
57.5
67.4
77.8
86.7
39.9
53.3
64.5
74.4
83.9
34.8
42.2
48.8
55.8
62.1
41.9
50.6
59.1
66.7
74.7
40.3
53.2
72.5
86.4
98.4
0.0045
81.0
106.9
95.1
93.5
68.1
81.7
110.2
0.0050
88.8
114.8
103.5
102.3
74.0
88.8
119.5
SET
0.0014
0.0013
0.0014
0.0013
0.0011
0.0016
0.0013
After thermal (left and right beam)
After Thermals
Sample # 0.0005
1
9.6
2
9.6
3
10.1
4
10.9
5
9.5
6
12.6
7
10.9
0.0010
17.9
21.9
20.2
20.0
18.7
23.2
20.8
0.0015
25.3
34.2
34.0
29.6
26.8
32.8
29.9
Page 31 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA Continued
A
B
DIELECTRIC WITHSTANDING
VOLTAGE
(DWV): C
10
11
12
13
14
15
16
17
18
D
Initial Breakdown Voltage
Test Voltage Until Breakdown Occurs
Mated
Sample#
107636-028
107636-029
A
10
11
12
13
14
15 Sample#
16 107636-032
17 107636-033
SFM/TFM
1100
1000
B
Mated
SFM/TFM
750
750
Pin to Pin
A Unmated
X
SFM
1100
1000
C
Initial DWV
Test Voltage= 750
Pin to Pin
A Unmated
SFM
750
750
B
TFM
1400
1300
D
B
TFM
750
750
Thermal Test Voltage
Test Voltage= 750
Sample#
107636-032
107636-033
Mated
SFM/TFM
750
750
Pin to Pin
A Unmated
SFM
750
750
B
TFM
750
750
Humidity Test Voltage
Test Voltage= 750
Sample#
107636-032
107636-033
Mated
SFM/TFM
750
750
Pin to Pin
A Unmated
SFM
750
750
Page 32 of 51
B
TFM
750
750
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA Continued
A
INSULATION RESISTANCE
(IR):
10
11
12
13
14
15
16 Sample#
17 107636-032
18 107636-033
B
C
Initial Insulation Resistance
Measured In Meg Ohms
Mated
X
SFM/TFM
100000
100000
D
Pin to Pin
A Unmated B
X
X
SFM
TFM
100000
100000
100000
100000
Thermal Insulation Resistance
Measured In Meg Ohms
Sample#
107636-032
107636-033
Mated
X
SFM/TFM
100000
100000
Pin to Pin
A Unmated B
X
X
SFM
TFM
100000
100000
100000
100000
Humidity Insulation Resistance
Measured In Meg Ohms
Sample#
107636-032
107636-033
Mated
X
SFM/TFM
100000
100000
Pin to Pin
A Unmated B
X
X
SFM
TFM
100000
100000
100000
100000
Page 33 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA Continued
LLCR Durability:
Board
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
mOhm
values
Position
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
Actual
Initial
6.1
6.3
6.3
6.1
6.8
6.7
6.7
6.1
6.0
6.0
6.1
6.3
6.2
6.6
6.7
6.8
6.4
7.2
7.0
6.8
6.4
6.3
6.3
6.1
6.3
6.5
7.1
6.2
6.4
7.1
7.1
6.5
6.3
6.3
6.5
6.5
6.4
6.5
6.7
6.6
6.5
6.5
7.1
7.1
6.9
Delta
100 Cycles
0.7
0.4
0.3
0.5
0.4
0.2
0.0
0.3
0.3
0.4
0.4
0.3
0.6
0.2
0.3
0.2
0.5
-0.2
-0.2
0.0
0.3
0.5
0.9
1.0
0.2
0.2
0.0
0.3
0.4
-0.1
0.0
0.0
0.5
0.6
0.4
0.2
0.4
0.5
0.2
0.4
0.5
0.3
0.0
-0.1
0.0
Page 34 of 51
Delta
Thermal
3.1
3.0
2.6
0.3
0.2
0.4
0.1
2.8
3.1
2.7
3.2
3.0
2.0
3.1
3.0
2.8
1.8
-0.4
-0.1
0.0
0.8
3.1
2.9
3.2
1.2
0.6
-0.2
0.4
0.7
0.0
0.0
-0.1
1.9
0.3
0.2
0.2
2.7
3.3
3.1
2.9
0.6
0.7
0.1
0.1
0.1
Delta
Humidity
3.3
3.2
2.7
0.3
0.1
0.4
0.1
3.2
3.1
2.9
3.4
3.2
2.2
3.3
3.2
2.9
2.1
-0.5
-0.2
0.0
1.7
3.4
3.1
3.3
1.2
0.5
-0.2
0.4
0.7
0.1
0.0
-0.1
2.0
0.3
0.2
0.3
2.9
3.5
3.2
3.0
0.6
0.7
0.3
0.1
0.0
Tracking Code: 107636_Report_Rev_2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
6.8
6.6
6.5
6.3
6.3
6.8
6.3
6.9
6.9
7.2
7.0
6.9
7.2
7.0
7.0
7.0
7.3
7.4
7.1
6.6
7.3
7.1
7.4
7.1
7.2
7.0
7.1
6.9
6.1
7.1
6.3
6.5
7.2
7.2
6.3
6.3
6.4
6.5
6.3
6.4
6.5
6.6
6.4
6.4
7.0
7.1
6.8
6.5
6.7
6.0
0.0
0.2
0.1
0.2
0.4
0.6
0.9
-0.1
0.1
0.0
0.0
-0.2
0.0
-0.2
0.0
0.1
-0.2
0.0
0.0
0.0
0.0
0.1
0.0
0.0
0.0
0.0
-0.1
0.3
0.5
-0.1
0.1
0.2
0.1
0.0
0.3
0.4
0.1
0.2
0.1
0.3
0.2
0.1
0.2
0.3
0.0
0.3
0.1
0.1
0.0
0.2
Page 35 of 51
0.0
0.0
0.2
0.4
1.1
0.3
1.8
-0.1
0.1
0.1
0.0
0.0
-0.2
0.0
-0.3
0.1
-0.3
-0.1
-0.1
0.3
-0.1
0.0
0.0
-0.1
-0.2
-0.1
-0.3
0.0
0.7
-0.3
1.0
0.2
0.1
0.1
0.4
0.3
0.4
0.3
0.3
0.4
2.8
0.2
2.4
0.5
-0.2
0.1
0.0
0.0
-0.1
0.8
0.0
0.1
0.5
0.4
1.1
0.5
1.7
-0.1
0.1
0.0
-0.1
0.0
-0.3
0.0
-0.3
0.0
-0.4
-0.1
-0.1
0.3
-0.1
0.0
0.0
-0.2
-0.1
-0.1
-0.3
0.0
0.7
-0.3
0.9
0.3
0.1
0.1
0.4
0.3
0.4
0.3
0.3
0.6
3.1
0.5
2.7
0.5
0.4
0.1
0.0
0.3
-0.1
0.7
Tracking Code: 107636_Report_Rev_2
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
6.1
6.3
6.4
6.8
6.3
6.8
6.9
7.0
6.9
7.0
6.4
7.1
6.8
6.5
7.0
7.2
6.5
6.6
7.0
6.9
6.6
6.8
6.2
6.6
6.0
6.5
6.5
6.6
6.8
7.3
7.2
7.4
6.8
6.8
6.1
6.7
6.5
6.9
7.2
6.8
7.1
6.8
7.5
7.3
7.1
7.0
6.8
6.4
6.6
6.7
0.1
0.5
0.5
0.1
0.6
0.0
0.0
0.0
0.1
-0.1
0.5
0.1
0.0
0.6
0.1
-0.1
0.8
0.5
0.2
0.0
0.1
-0.1
0.5
0.0
0.2
0.3
0.6
0.4
0.1
0.0
0.1
-0.1
0.0
0.0
0.3
0.1
0.4
0.0
-0.1
0.0
0.0
0.3
0.0
0.2
0.0
0.1
0.3
0.2
0.4
0.2
Page 36 of 51
0.3
0.7
1.5
-0.1
1.2
-0.1
0.1
0.0
0.0
-0.1
0.7
0.2
0.1
0.8
0.1
-0.3
1.1
0.9
0.0
-0.1
0.1
-0.3
0.6
-0.2
0.6
0.8
0.6
0.7
0.0
-0.1
0.1
0.0
-0.1
0.0
0.8
0.2
0.6
0.0
-0.2
0.5
-0.1
0.4
-0.1
0.2
0.0
-0.1
2.6
0.5
0.3
0.0
0.3
0.6
1.7
-0.1
1.2
-0.1
0.1
0.0
-0.1
-0.1
0.6
0.2
0.0
0.8
0.0
-0.2
1.1
0.9
0.2
0.3
0.1
-0.2
0.7
-0.1
0.6
0.8
0.6
0.6
0.0
-0.1
0.1
0.0
0.0
0.0
0.6
-0.2
0.5
0.0
-0.3
0.4
-0.1
0.3
0.0
0.1
0.1
0.0
2.9
0.5
0.3
0.1
Tracking Code: 107636_Report_Rev_2
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
6.7
6.5
7.3
6.7
6.9
7.7
7.3
7.2
6.5
7.7
7.2
6.6
7.6
7.4
6.6
7.4
7.5
7.4
7.2
7.0
7.1
6.8
6.3
6.8
6.8
7.0
6.4
6.6
6.8
7.5
7.1
7.2
7.0
6.7
7.3
6.7
7.6
6.9
6.6
6.8
7.6
7.7
7.5
7.0
6.5
6.9
6.2
0.0
0.6
0.1
0.1
0.4
0.1
0.1
0.0
0.3
0.0
0.2
0.6
-0.1
0.1
0.9
0.2
0.1
0.0
0.0
0.0
0.0
-0.1
0.5
0.0
0.0
0.0
0.5
0.1
0.0
-0.1
-0.1
-0.1
0.2
1.0
0.0
0.8
-0.1
0.5
0.4
0.5
0.0
0.0
0.1
0.1
0.5
0.0
0.5
Page 37 of 51
0.0
0.6
-0.1
-0.1
0.1
0.0
-0.2
0.0
1.1
-0.3
-0.1
1.6
-0.2
-0.2
2.1
-0.1
0.0
0.1
0.0
-0.1
0.0
-0.1
0.6
0.0
-0.1
-0.1
0.7
0.1
0.0
0.0
-0.1
-0.3
0.3
2.0
-0.2
2.6
-0.2
2.4
1.0
0.7
-0.2
-0.1
0.2
0.0
1.0
-0.1
1.7
0.1
0.7
0.0
-0.1
0.1
-0.1
0.0
0.0
0.9
-0.3
-0.1
1.2
-0.2
-0.2
2.7
-0.1
-0.1
0.4
0.0
-0.2
-0.1
-0.1
0.6
0.0
-0.1
-0.1
0.8
0.1
0.1
0.0
-0.1
-0.2
0.3
2.0
-0.2
2.3
-0.2
2.7
0.6
0.6
-0.1
-0.1
0.1
0.0
0.9
-0.1
1.6
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA Continued
LLCR Thermal aging:
Board
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
mOhm values
Position
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
Actual
Initial
7.0
7.1
7.1
7.0
7.4
7.1
7.3
6.7
7.0
7.0
7.3
7.1
7.1
7.0
7.2
6.9
7.1
7.3
7.3
6.9
6.6
6.7
6.7
6.8
6.5
6.3
6.7
6.5
6.2
6.7
7.1
7.0
6.2
6.2
6.3
7.2
7.2
6.6
7.1
7.0
7.2
7.2
7.2
7.1
6.4
6.6
Page 38 of 51
Delta
Thermal Age
0.0
0.1
0.0
0.0
-0.1
0.1
0.1
0.0
0.0
0.0
0.0
0.0
0.1
0.1
0.0
0.0
0.0
-0.1
0.0
0.3
0.2
0.0
0.0
0.0
0.0
0.0
0.3
-0.1
0.1
0.3
0.1
0.1
0.0
0.0
0.0
0.0
0.0
-0.1
0.0
0.1
0.1
-0.2
-0.1
0.4
0.0
-0.1
Tracking Code: 107636_Report_Rev_2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
6.4
6.3
7.5
7.3
7.3
7.3
6.8
7.0
7.2
6.8
6.9
6.9
7.1
6.9
7.1
7.0
7.1
7.1
7.1
7.1
7.2
7.1
7.3
7.1
7.0
7.1
6.4
6.5
6.3
6.4
6.3
6.4
7.2
6.3
6.8
6.4
7.1
6.8
6.4
6.9
7.0
6.3
6.9
6.4
6.8
7.6
6.3
6.5
6.5
6.3
Page 39 of 51
-0.1
0.0
0.0
0.1
0.1
0.1
0.1
0.3
0.0
0.3
0.2
0.0
0.1
0.1
0.1
0.0
0.0
0.0
0.1
0.0
0.0
0.1
0.0
0.0
0.0
-0.1
0.0
-0.2
0.0
-0.1
0.0
0.3
0.1
0.2
0.0
0.4
0.0
0.0
0.0
-0.1
0.0
0.0
0.1
0.7
0.0
0.5
0.0
0.0
0.2
0.1
Tracking Code: 107636_Report_Rev_2
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
6.8
6.9
7.0
6.8
6.7
6.5
6.6
6.5
6.7
6.6
6.7
6.7
6.9
7.0
7.0
6.8
6.9
7.0
7.1
6.7
6.7
6.7
6.6
6.6
7.1
6.8
7.1
6.9
6.6
6.6
7.0
6.8
7.1
7.0
7.2
7.2
7.1
7.2
7.4
7.0
6.8
7.4
7.1
7.0
7.1
7.2
7.0
7.1
7.2
6.9
Page 40 of 51
0.2
0.0
0.0
0.0
0.2
0.1
0.0
0.1
0.0
0.0
-0.1
-0.1
-0.1
-0.1
0.0
0.1
0.0
-0.2
-0.1
0.0
0.1
0.0
0.0
-0.1
0.0
0.1
-0.1
-0.1
0.3
0.2
0.0
0.0
0.0
0.0
0.0
0.1
0.2
0.0
0.1
-0.3
-0.1
0.0
0.0
0.1
0.1
0.0
0.0
0.0
-0.1
0.1
Tracking Code: 107636_Report_Rev_2
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
7.0
6.6
6.7
6.6
6.6
6.4
6.4
6.5
6.7
6.6
6.7
6.8
6.9
6.8
6.8
6.8
6.7
6.9
6.8
6.8
6.7
6.8
7.2
7.0
7.2
7.2
7.0
6.9
7.2
7.0
7.1
7.0
7.0
7.3
7.4
7.1
7.1
7.1
7.1
7.1
7.0
7.5
7.4
7.3
7.2
7.3
Page 41 of 51
0.0
0.0
0.2
0.1
0.1
0.0
-0.1
-0.1
-0.1
0.0
0.0
0.0
0.0
0.0
0.0
0.1
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.1
0.0
0.0
0.1
0.1
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.1
0.1
0.0
0.0
0.0
0.0
0.0
0.1
0.0
0.0
0.0
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA Continued
LLCR Shock/Vibration:
Board
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
mOhm
values
Actual
Position
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
Initial
6.3
6.1
6.4
6.3
6.8
6.7
7.2
6.1
6.1
6.3
6.4
6.3
6.4
6.6
6.5
6.7
6.4
6.3
6.9
7.0
6.4
6.4
6.2
6.4
6.2
6.3
6.5
6.3
6.9
7.1
7.0
6.5
6.4
6.4
6.4
6.5
6.4
6.5
6.6
6.7
6.4
6.9
7.0
6.9
Page 42 of 51
Delta
Shock /
Vibe
-0.1
-0.1
0.2
0.5
-0.1
1.8
-0.2
0.2
0.1
0.0
0.0
0.0
-0.1
-0.1
0.0
0.1
0.0
0.0
-0.3
2.2
-0.3
0.0
0.0
-0.1
0.0
-0.1
0.0
0.1
0.0
2.0
-0.1
0.0
0.2
0.1
0.0
-0.2
-0.1
0.1
0.2
0.0
-0.1
-0.1
-0.2
1.2
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
6.6
6.8
6.6
6.7
6.3
6.3
6.2
6.3
7.0
6.9
7.3
6.3
6.4
6.2
6.6
6.4
6.4
6.4
6.4
6.3
6.4
6.6
7.1
7.2
6.6
6.5
6.3
6.3
6.5
6.6
7.0
7.0
6.7
7.0
7.6
7.3
7.3
6.6
7.2
6.9
7.1
7.1
6.6
7.4
7.4
7.5
7.4
7.0
6.8
7.0
Page 43 of 51
0.0
-0.1
0.0
-0.1
0.0
0.1
0.1
0.4
-0.2
-0.2
-0.4
0.1
0.1
0.1
0.2
0.1
0.1
0.2
0.1
0.1
0.0
0.3
-0.2
1.4
0.5
0.3
0.2
0.1
0.2
0.0
-0.1
-0.1
-0.1
0.5
0.0
-0.1
-0.1
0.3
-0.1
-0.1
-0.2
-0.4
1.5
-0.4
-0.1
-0.3
-0.5
0.2
-0.1
-0.1
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
4
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
6.9
6.8
6.5
6.4
6.4
6.6
6.9
7.1
7.2
6.7
6.5
6.2
6.4
6.3
6.4
6.5
6.7
7.4
7.4
7.4
7.7
7.0
6.6
6.7
6.8
6.3
6.1
6.8
6.4
6.8
7.1
7.2
7.4
6.9
6.9
6.3
6.7
6.5
6.5
6.5
6.7
6.6
7.0
6.7
7.0
6.8
6.7
6.5
6.2
6.3
Page 44 of 51
-0.1
0.0
0.4
0.0
0.0
0.3
0.0
0.9
0.0
-0.1
0.2
-0.1
-0.1
0.0
0.1
0.1
0.1
0.0
-0.1
-0.2
-0.5
-0.1
0.3
-0.2
0.0
-0.1
0.0
-0.5
0.0
0.0
-0.1
0.8
-0.2
0.0
0.0
0.1
-0.2
0.1
0.2
0.0
0.0
0.0
-0.1
-0.2
-0.4
3.3
-0.1
0.3
-0.1
0.0
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
6.4
6.4
6.5
7.4
7.0
7.1
7.2
6.8
6.8
6.7
7.1
6.7
7.1
7.1
7.5
7.3
8.2
8.0
7.3
7.4
7.1
7.3
7.1
7.1
6.1
6.2
6.3
6.3
7.0
7.2
6.9
6.1
6.2
6.0
6.3
6.4
6.4
6.5
6.5
6.4
6.3
6.3
6.7
6.7
6.2
6.5
6.3
6.3
Page 45 of 51
0.0
0.0
0.0
-0.6
0.0
0.5
-0.2
-0.1
0.0
0.0
-0.1
-0.1
-0.2
-0.3
-0.6
-0.1
-0.7
-0.8
-0.5
1.9
-0.1
-0.3
-0.2
-0.1
0.0
0.0
0.1
0.0
0.0
-0.2
0.1
0.1
0.0
0.0
0.0
0.0
0.0
0.0
0.1
0.1
0.0
0.2
0.0
0.1
0.6
-0.1
0.0
0.0
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
DATA Continued
LLCR Gas Tight
Board
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
mOhm
values
Position
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
Actual
Initial
7.3
7.1
7.4
7.0
7.0
7.1
7.4
7.1
7.2
7.2
7.8
7.2
7.3
7.2
7.2
7.1
7.2
7.1
6.9
7.2
7.4
7.3
7.2
7.2
6.6
6.6
6.6
6.5
6.3
6.8
7.4
6.5
6.5
6.4
6.6
6.3
6.4
6.5
6.5
6.4
6.5
6.8
7.5
7.3
6.6
Page 46 of 51
Delta
Gas Tight
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
-0.1
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.1
0.1
0.1
0.6
0.7
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.5
0.6
0.8
0.4
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
6.8
6.4
6.4
6.6
6.8
6.4
6.4
6.4
6.6
7.1
6.8
6.2
7.0
6.1
6.9
6.3
6.1
6.2
7.1
7.1
6.5
6.8
6.7
6.1
6.2
6.1
7.3
6.8
6.0
6.2
6.2
5.6
6.4
6.6
5.9
5.9
6.0
6.0
5.9
6.2
6.0
6.3
6.4
6.3
6.3
7.7
6.2
6.3
5.9
6.4
Page 47 of 51
0.1
0.1
0.1
0.3
0.1
0.2
0.1
0.1
0.1
0.1
0.2
0.2
0.1
0.1
0.1
0.1
0.0
0.0
0.1
0.1
0.3
0.1
0.2
0.2
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.2
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.2
0.1
0.1
0.1
0.1
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
4
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
6.4
6.6
5.8
5.9
5.9
6.0
5.7
6.4
6.0
6.0
5.9
6.0
5.9
6.1
6.2
6.2
6.0
6.3
8.0
7.0
6.4
5.8
5.8
5.8
5.9
7.1
7.4
7.5
6.9
7.1
7.2
7.3
6.7
7.0
6.9
7.2
6.6
6.8
7.2
7.0
6.9
7.3
7.8
7.1
7.1
7.0
7.0
6.9
6.7
6.9
Page 48 of 51
0.1
0.1
0.0
0.0
0.2
0.2
0.2
0.2
0.2
0.3
0.2
0.1
0.1
0.2
0.4
0.1
0.0
0.1
0.4
0.1
0.3
0.1
0.0
0.0
0.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
-0.1
-0.1
0.1
0.1
0.0
0.1
0.1
0.0
0.0
0.0
0.1
0.1
0.1
0.1
0.1
0.1
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
6.6
6.8
6.9
6.6
6.4
6.8
6.9
6.9
6.9
6.9
6.7
7.1
7.2
7.3
7.1
6.6
7.1
7.1
6.8
6.9
7.0
6.9
7.2
7.2
7.5
7.0
6.9
6.8
6.7
6.8
6.4
6.4
6.5
6.6
6.7
6.7
6.8
6.8
6.7
6.8
7.0
6.8
6.9
6.9
6.9
6.8
6.8
Page 49 of 51
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.0
0.1
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.0
0.0
0.0
0.1
0.1
0.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.1
0.0
0.0
0.1
0.1
0.1
0.0
0.1
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
EQUIPMENT AND CALIBRATION SCHEDULES
Equipment #: TSC-01
Description: Vertical Thermal Shock Chamber
Manufacturer: Cincinnati Sub Zero
Model: VTS-3-6-6-SC/AC
Serial #: 10-VT14993
Accuracy: See Manual
… Last Cal: 05/18/2010, Next Cal: 05/18/2011
Equipment #: MO-01
Description: Micro-ohmmeter
Manufacturer: Keithley
Model: 580
Serial #: 0772740
Accuracy: Last Cal: 2010-4-30, Next Cal: 2011-4-30
Equipment #: THC-01
Description: Temperature/Humidity Chamber
Manufacturer: Thermotron
Model: SM-8-7800
Serial #: 30676
Accuracy: See Manual
… Last Cal: 08/16/2010, Next Cal: 02/16/2011
Equipment
#: OV-03
Description: Cascade Tek Forced Air Oven
Manufacturer: Cascade Tek
Model: TFO-5
Serial #: 0500100
Accuracy: Temp. Stability: +/-.1C/C change in ambient
Last Cal: 06/16/2010, Next Cal: 206/16/2011
Equipment #: TCT-01
Description: Normal force analyzer
Manufacturer: Mecmesin Multitester
Model: Mecmesin Multitester 2.5-i
Serial #: 04-1041-04
Accuracy: Last Cal: 05/21/2010, Next Cal: 05/20/2011
Equipment #: MO-04
Description: Multimeter /Data Acquisition System
Manufacturer: Keithley
Model: 2700
Serial #: 0798688
Accuracy: See Manual
… Last Cal: 4/30/2010, Next Cal: 4/30/2011
Page 50 of 51
Tracking Code: 107636_Report_Rev_2
Part #: SFM-150-02-S-D-A/TFM-150-02-S-D-A
Part description: SFM/TFM
EQUIPMENT AND CALIBRATION SCHEDULES
Equipment #: ED-03
Description: Event Detector
Manufacturer: Analysis Tech
Model: 32EHD
Serial #: 1100604
Accuracy: See Manual
… Last Cal: 06/04/2010, Next Cal: 06/04/2011
Equipment #: TCT-07
Description: Automated Test Stand
Manufacturer: Chatillon/Lloyd
Model: LF Plus
Serial #: LF1310
Accuracy: See Manual
… Last Cal: 07/15/2010, Next Cal: 07/15/2011
Equipment #: ACLM-01
Description: Accelerometer
Manufacturer: PCB Piezotronics
Model: 352C03
Serial #: 115819
Accuracy: See Manual
… Last Cal: 07/09/2010, Next Cal: 07/09/2011
Equipment #: SVC-01
Description: Shock & Vibration Table
Manufacturer: Data Physics
Model: LE-DSA-10-20K
Serial #: 10037
Accuracy: See Manual
… Last Cal: 11/31/2009, Next Cal: 11/31/2010
Page 51 of 51