Product Specification Series: LPHS / LPHT .050” (1,27 mm) EXTreme LPHPower™ Signal/Power Socket and Terminal Assembly LPHS Series – Socket, Vertical Orientation LPHT Series – Terminal, Right Angle Orientation Other configurations available for: Right Angle Socket applications Mating card combinations See www.samtec.com for more information. Revision: A Date: January 3, 2014 Page 1 © Samtec, Inc. Product Specification Series: LPHS / LPHT .050” (1,27 mm) EXTreme LPHPower™ Signal/Power Socket and Terminal Assembly 1.0 SCOPE 1.1 This specification covers performance, testing and quality requirements for Samtec LPHS / LPHT Series .050” (1,27 mm) EXTreme LPHPower™ 30 A per power blade Signal/Power Socket and Terminal Assembly. All information contained in this specification is for a Vertical socket / Right Angle terminal mated configuration unless otherwise noted. Right Angle socket / Right Angle terminal mated configuration is available on www.samtec.com. 2.0 DETAILED INFORMATION 2.1 Product prints, footprints, catalog pages, test reports and other specific, detailed information can be found at http://www.samtec.com/?LPHS and http://www.samtec.com/?LPHT. 3.0 TESTING 3.1 3.2 3.3 3.4 Current Rating: Power: 33A / Signal: 2.5A (One Pin Powered Per Row) Voltage Rating: 220 VAC (Signal) Operating Temperature Range: -55°C to +125°C Electrical: ITEM TEST CONDITION REQUIREMENT STATUS Withstanding Voltage EIA-364-20 (No Flashover, Sparkover, or Breakdown) 655 VAC Pass Insulation Resistance EIA-364-21 (1000 MΩ minimum) 5,000 MΩ Pass Contact Resistance (LLCR) EIA-364-23 Δ 15 mΩ maximum (Samtec defined)/ No damage Pass 3.5 Mechanical: ITEM TEST CONDITION REQUIREMENT STATUS Durability EIA-364-09C 100 cycles Pass Random Vibration EIA-364-28 Condition V, Letter B 7.56 G 'RMS', 50 to 2000 Hz, 2 hours per axis, 3 axis total , PSD 0.04 Visual Inspection: No Damage LLCR: Δ 15 mΩ maximum Event Detection: No interruption > 50 Nanoseconds Pass Mechanical Shock EIA-364-27 100 G, 6 milliseconds, sawtooth wave, 11.3 fps, 3 shocks/direction, 3 axis (18 total shocks) Visual Inspection: No Damage LLCR: Δ 15 mΩ maximum Event Detection: No interruption > 50 Nanoseconds Pass Normal Force EIA-364-04 30 grams minimum for Gold interface Pass Revision: A Date: January 3, 2014 Page 2 © Samtec, Inc. Product Specification Series: LPHS / LPHT .050” (1,27 mm) EXTreme LPHPower™ Signal/Power Socket and Terminal Assembly 3.6 Environmental: ITEM TEST CONDITION REQUIREMENT STATUS Thermal Shock EIA-364-32 Thermal Cycles: 100 (30 minute dwell) Hot Temp: +85°C Cold Temp: -55°C Hot/Cold Transition: Immediate Visual Inspection: No Damage LLCR: Δ 15 mΩ DWV: 655 VAC IR: >5,000 MΩ Pass Thermal Aging (Temp Life) EIA-364-17 Test Condition 4 @ 105°C Condition B for 250 hours Visual Inspection: No Damage LLCR: Δ 15 mΩ DWV: 390 VAC IR: >5,000 MΩ Pass Cyclic Humidity EIA-364-31 Test Temp: +25°C to +65°C Relative Humidity: 90 to 95% Test Duration: 240 hours Visual Inspection: No Damage LLCR: Δ 15 mΩ DWV: 655 VAC IR: >5,000 MΩ Pass Gas Tight EIA-364-36 Gas Exposure: Nitric Acid Vapor Duration: 60 min. Drying Temp.: 50°C +/- 3°C Measurements: Within 1 hour of Exposure LLCR: Δ 15 mΩ Pass 4.0 MATED SYSTEM Mated view information can be found at link below: http://www.samtec.com/documents/webfiles/cpdf/LPHX%20Mated%20Document-MKT.pdf Revision: A Date: January 3, 2014 Page 3 © Samtec, Inc. Product Specification Series: LPHS / LPHT .050” (1,27 mm) EXTreme LPHPower™ Signal/Power Socket and Terminal Assembly 5.0 POLARIZING FEATURES 6.0 PROCESSING RECOMMENDATIONS 6.1 Mating Alignment Requirements: 6.1.1 Revision: A Maximum guidance/capture in applications where at least one half of the interface is free to float. Date: January 3, 2014 Page 4 © Samtec, Inc. Product Specification Series: LPHS / LPHT .050” (1,27 mm) EXTreme LPHPower™ Signal/Power Socket and Terminal Assembly 6.1.2 The parts can be rigidly misaligned by no more than .003” (0,08 mm) in the X- and .003’’ (0,08 mm) in the Y-direction to ensure a good mate. 6.2 Mating Angle Requirements: For LPHS mated with LPHT, Connectors to be mated and unmated axially only, zippering angles may damage connector and/or solder joints; for LPHS mated with card, the connector can be zippered 2° in both the longitudinal and lateral directions. 6.2.1 6.2.2 Revision: A Date: January 3, 2014 Page 5 © Samtec, Inc. Product Specification Series: LPHS / LPHT .050” (1,27 mm) EXTreme LPHPower™ Signal/Power Socket and Terminal Assembly 6.2.3 6.2.4 6.3 Press Fit Tooling Application: Revision: A Date: January 3, 2014 Page 6 © Samtec, Inc. Product Specification Series: LPHS / LPHT .050” (1,27 mm) EXTreme LPHPower™ Signal/Power Socket and Terminal Assembly 7.0 ADDITIONAL RESOURCES 7.1 For additional mechanical testing or product information, contact our Customer Engineering Support Group at [email protected] 7.2 For additional information on high speed performance testing, contact our Signal Integrity Group at [email protected] 7.3 For additional processing information, contact our Interconnect Processing Group at [email protected]. 7.4 For RoHS, REACH or other environmental compliance information, contact our Product Environmental Compliance Group at [email protected] * EXTreme LPHPower™ is a trademark of Molex Incorporated. Revision: A Date: January 3, 2014 Page 7 © Samtec, Inc.