HGXO OSCILLATOR 460 kHz to 50 MHz High Shock Surface Mount Crystal Oscillator ™ DESCRIPTION Statek’s HGXO crystal oscillator is an ultra-miniature, surface-mount oscillator that can survive extremely high shocks _ up to 100,000 g. The design consists of a hermetically-sealed high-shock crystal and a CMOS compatible integrated circuit housed in a 5.0 mm x 7.5 mm surface-mount ceramic package. actual size side view FEATURES Mechanical shock survivability up to 100,000 g PACKAGE DIMENSIONS CMOS output, TTL on request Optional Tri-State or Output Enable G Low EMI emission Designed for surface mount: infrared, vapor phase, wave solder, or epoxy mount Full military testing to MIL-PRF-55310 available Hermetically sealed ceramic package D A 2 3 1 4 F TOP Low g-sensitivity available D SM1 version lead free APPLICATIONS B C E Industrial Transmitter reference oscillator TYPICAL Clock oscillator MAXIMUM DIM inches mm inches mm A 0.295 7.50 0.302 7.68 Smart Munitions B 0.197 5.00 0.204 5.18 Projectile Electronics C* 0.089 2.25 0.098 2.50 D 0.055 1.40 - - E 0.040 1.02 - - Military & Aerospace SUGGESTED LAND PATTERN 0.060 (1.52) 0.040 (1.02) F 0.240 6.10 - - G 0.100 2.54 - - *SM1 (Termination material is Au over Ni over W). Solder dip (SM3) also available 0.075 (1.91) PIN CONNECTIONS 0.240 (6.10) 0.165 (4.19) 1. Output Enable (E), Tri-State (T), or NC (N) 2. Ground 3. Output 4. VDD GRID PLACEMENT COURTYARD 10156 - Rev A IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com YS 90 01 TEM C ERT I F I C AT N IO S inches (mm) 0.100 (2.54) SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS Specifications are typical at 25OC unless otherwise noted. Specifications are subject to change without notice. Supply Voltage VDD -0.5 V to 7.0 V Storage Temperature -55OC to +125OC Maximum Process Temperature 260OC, 10 seconds Supply Voltage 1.8V to 5V, as required + _ Calibration Tolerance Frequency Stability Over Temperature1 5 ppm minimum and up 10 ppm and up for Commercial + _ 20 ppm and up for Industrial + _ + _ 30 ppm and up for Military Total Frequency + _ 15 ppm and up for Commercial Tolerance2 + _ 20 ppm and up for Industrial + _ 35 ppm and up for Military ENABLE / TRI-STATE E T N PIN 1* Low PIN 3 High Z High Low Freq. Output High Z High Freq. Output NC Freq. Output CMOS Load3 15 pF Start-up Time 10 ms MAX Rise/Fall Time 8 ns MAX Duty Cycle 40% MIN, 60% MAX Shock survival Up to 100,000 g peak, 0.5 ms,1/2 sine ENABLE (E) VS. TRI-STATE (T) Vibration survival 20 g RMS 10-2000 Hz random E Standard Operating Temperature Ranges -10OC to +70OC (Commercial) -40OC to +85OC (Industrial) -55OC to +125OC (Military) T * Normally high (internal pull-up resistor) 1. Does not include calibration tolerances. 2. Frequency over temperature relative to nominal frequency. 3. TTL loads and higher CMOS loads available. Contact factory. PACKAGING OPTIONS When pin 1 is low, the oscillator stops oscillating. When pin 1 is low, the internal oscillator continues to run, however, the output (pin 3) is in a high impedance (Z) state. E T Current consumption Very Lower than when pin 1 is low Low Normal Output recovery delay when pin 1 changes from Delayed Immediate low to high HGXO - Tray Pack - Tape and Reel (Reference tape and reel data sheet 10109) HOW TO ORDER HGXO SURFACE MOUNT CRYSTAL OSCILLATORS HGXO Supply Voltage 1 = 1.8V 2 = 2.5V 3 = 3.0V 4 = 3.3V 5 = 5.0V 3 D Shock Level A = 5,000 g B = 10,000 g C = 20,000 g D = 30,000 g F = 50,000 g G = 75,000 g H = 100,000 g S “S” if special or custom design. Blank if Std. T SM3 E = Enable Blank = SM1 T = Tri-State = Gold Plated N = Neither SM3 = Gold Plated + Solder Dipped 20.0M Frequency K = kHz M = MHz , 30 / 50 / / Frequency Stability over Temp.Range (in ppm) Calibration Tolerance @ 250C (in ppm) I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified OR / / 100 Total Frequency Tolerance (in ppm) / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com YS 90 01 TEM C ERT I F I C AT N IO S 10156 - Rev A