Field Terminated Cassettes Part Numbers: FCX-12-10KIT/N, FC9-12-10KIT/N, FC9-4-3AKIT/N © Panduit Corp. 2009 ASSEMBLY INSTRUCTIONS Note: FCX-12-10KIT/N shown. FC9-12-10KIT/N and FC9-4-3AKIT/N are similar for SC and APC connectors. Enclosure Preparation Cable needs to be fed through enclosure before terminating the cable into the cassette. 1. End of cable is slid through grommet on enclosure. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 1 of 8 FS009 ASSEMBLY INSTRUCTIONS © Panduit Corp. 2009 FS009 2. It is recommended that 1622 mm [60.5 in.] of cable be fed through the grommet on the enclosure. (1000 mm [39.4 in.] of cable for spooling in the enclosure and 622 mm [24.5 in.] of cable stored in the cassette). Material ABMM-A-C Cable Tie Mount LC3-A Latching Clip Cassette Corrugated Loom Tubing CLT25F-C20 Cassette Front Panel with LC Connectors Pan-Ty For Technical Support: www.panduit.com/resources/install_maintain.asp Page 2 of 8 © Panduit Corp. 2009 ASSEMBLY INSTRUCTIONS Cassette Preparation 1. Install cable tie mount into cassette framing just inside the cable port on the rear of the cassette as shown. 2. Insert Feed 1000mm [39.4 in.] of fiber cable through corrugated loom tubing and slide through the cable port at the rear of the cassette. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 3 of 8 FS009 © Panduit Corp. 2009 ASSEMBLY INSTRUCTIONS 3. Secure corrugated tube and cable loosely to the anchor installed in Step 1 using small Pan-Ty. The fiber cable should be able to be pulled through for terminating the fiber ends. 4. Install cable latch clips in the center of the cassette as shown. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 4 of 8 FS009 ASSEMBLY INSTRUCTIONS © Panduit Corp. 2009 Fiber Cable Preparation After the cable is installed and secure in the cassette: 1. Pull the fiber cable through the end of the corrugated loom tubing. Mark fiber cable at 622 mm [24.5 in.] from cut end of cable. Pull off cable jacketing and cut back Kevlar flush with the end of the jacketing so only 900um fiber is exposed for the 622 mm [24.5 in.] length. 2. Follow installation instructions per PN340* LC Fiber Optic Connector Field Polish Termination Instructions. * Denotes instruction sheet revision letter. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 5 of 8 FS009 © Panduit Corp. 2009 ASSEMBLY INSTRUCTIONS Cable Routing 1. Install polished LC connectors into the adapter within the cassette module. Be sure to follow TIA/EIA color code standards. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 6 of 8 FS009 © Panduit Corp. 2009 ASSEMBLY INSTRUCTIONS 2. Once the adapters are installed, slide the fiber cable back though the corrugated loom tubing. Tightly secure the tubing and fiber cable as shown. 3. Dress fiber into cassette under the cable slack management clips as shown. Install the fiber adapter panel into the cassette. 4. Install cover onto cassette ensuring not to pinch any of the 900µm buffer cabling. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 7 of 8 FS009 ASSEMBLY INSTRUCTIONS © Panduit Corp. 2009 FS009 Installing Cassette into Enclosure 1. Pull loom tubing / fiber cable slack back into enclosure and slide cassette into on enclosure housing. 2. Snap enclosure into place. 3. Route slack as per instructions for enclosure being utilized. E-mail: [email protected] For Instructions in Local Languages and Technical Support: www.panduit.com/resources/install_maintain.asp www.panduit.com Page 8 of 8 Fax: (708) 444-6993