PANVIEW iQ (PViQ) Angled Patch Panel Part Numbers: PVQ-MIQAPU24, PVQ-MIQAPS24 INSTALLATION INSTRUCTIONS © Panduit Corp. 2009 PN506A Hardware Components (4) ULTIMATE ID Label Covers PANVIEW iQ Angled Patch Panel (6) #12-24 x 0.5" Grounded Bonding Screws* (6) M6 x 1.0 x 16 Grounded Bonding Screws* * Only 4 screws are needed for installation. Rack Mounting and Grounding 1. 2. If supplied screws do not fit or work with your rack or rack cabinet to provide appropriate grounding, the following screws are recommended: • Thread Forming Screw, M5 x 12mm (Part # RGTSM5-C) PM Installation EM Installation Install screws in 4 places EM Installation • Thread Forming Screw, #10-32 x 1/2" (Part # RGTS1032-C) EM Installation Use ONLY supplied grounding screws While PViQ Patch Panels work interchangeably with either the Panel Manager (PM) or the Expansion Module (EM), it is recommended that PViQ Patch Panels be placed in a manner that will efficiently accommodate one (1) PM for every three (3) EMs. NOTE: PM can be arranged at either the top or bottom of order depending on need or preference. Mount the PViQ Patch Panel onto the face of the rack or rack cabinet using four (4) of the supplied grounding screws as shown. Use either the #12-24 x 0.5" or M6 x 1.0 x 16 screws depending on the rack or cabinet. PViQ Patch Panels MUST be properly grounded to ensure accurate system operation. MINI-COM Module Installation (Recommended) Cable Routing Leave room for Mounting Bracket 3. With the PViQ Patch Panel secured to the rack or cabinet, proceed to install terminated jack modules into the patch panel (as shown above). NOTE: The PViQ Patch Panel accepts all MINI-COM Copper Jack Modules and LC Fiber Adapters. It is advisable to prepare cable management by routing cables into a left/right separation as you install the terminated jack modules (as shown above) to reserve appropriate space for the addition of mounting bracket later. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 1 of 2 © Panduit Corp. 2009 INSTALLATION INSTRUCTIONS PN506A Label / Label Cover Installation Suggested Label Solutions for TIA/EIA-606-A Compliance 4. Patch Panel Part Number All PViQ Patch Panels Laser/Ink Jet Desktop PANTHER LS8E Hand- COUGAR LS9 HandPrinter Label Held Printer Label Held Printer Label UILJ6 UILS8BW UILS8BW To label PViQ Panel according to TIA/EIA-606-A standard, ULTIMATE ID labels (not included) should be created and installed (as shown). Label covers (included) should be installed to protect the label. Label* Label Cover * Write on labels are not included with this patch panel per TIA-EIA-606-A standard which states: “To maximize legibility, all labels shall be printed or generated by a mechanical device, and shall not be written by hand.” (Refer to table above for label products) WARNINGS: If a non-PANDUIT power source is used, it must: • Provide over current protection appropriate to the size of the power wiring connected to the PViQ System. • Provide an isolated (SELV) source per National requirements. • Be certified for use with ITE equipment per National requirements. • Provide a nominal 12VDC source to the PM (min. 11.4VDC and max 12.6VDC). • Provide a 12VDC output which is electrically isolated from earth ground (minimum 1500 V isolation). • Have an output power rating of minimum 30W, which is sufficient for powering PViQ System and associated loads. PViQ European Emissions Warning: Product is not intended for use in a residential environment. Use of this product in residential areas may cause electromagnetic interference. Notes: 1. Never touch un-insulated communications wiring or terminals unless the communication line has been disconnected at the network interface. 2. Only trained and qualified service personnel should install or service PViQ Systems. 3. Before installing or servicing PViQ or communication wiring, be aware of the potential for electrostatic discharge (ESD). ATTENTION: Observe precautions for handling electrostatic sensitive electronic devices when installing this product. Ensure that you are properly grounded with a wrist strap or equivalent while installing PM or EM modules. E-mail: [email protected] For Instructions in Local Languages and Technical Support: www.panduit.com/resources/install_maintain.asp www.panduit.com Page 2 of 2 Fax: (708) 444-6993