● ● ● ● ● ● Features LED DRIVER Universal AC Input Constant Voltage / Constant Current Operation Active Power Factor Correction IP67 Design for Indoor and Outdoor Use Cooling by Free Air Convection PSE Certified for Japan market LIGHTLINE AC/DC-Converter with 5 year Warranty Description The RACD100-PSE LED driver series offer 100W of power with a universal input voltage range of 90-130VAC and constant current output up to 8.3A at a voltage of approximately 12V. The series feature a unique dual mode operation for either constant current or constant voltage making them suitable for driving LEDs directly or via local constant-current DC/DC modules directly on the light engine board. The RACD100-PSE series are fully sealed IP67 LED drivers and therefore ideally suited for indoor and outdoor applications including road, street and walkway lighting, high-bay, LED signage, and outdoor area lighting for car parks, public buildings, and tunnels. The LED drivers are PSE certified and come with a 5 year warranty. Selection Guide Part Number 100 Watt Single Output CV Mode CC Mode Efficiency Constant Voltage Current Range DC Voltage Range Constant Current (115VAC) (V) (A) (V) (A) (%) RACD100-12-PSE 12 0-8.3 9-12 8.3 87 RACD100-24-PSE 24 0-4.2 14-24 4.2 87 RACD100-36-PSE 36 0-2.8 26-36 2.8 89 RACD100-48-PSE 48 0-2.1 34-48 2.1 88 Specifications Input Voltage Range Input Frequency Range Power Factor THD AC Current Input/Output Isolation Input/Case Isolation Output/Case Isolation Leakage Current Voltage Tolerance Start-up Time Ripple & Noise (at 20MHz bandwith) Over Current Protection Short Circuit Protection Over Voltage Protection Latch Mode (Power off to recover) Full Load, 115VAC Full Load, 115VAC 115VAC Full Load, 115VAC 95%-105% rated current 12V 24V 36V 48V Over Temperature Protection Operating Temperature Range without derating (free air convection, according to PSE) Case Temperature Operation Humidity Storage Temperature Storage Humidity Vibration IP Rating EMC Standards (designed to meet) EMC Compatibility Harmonic Current EMC Immunity L-60 90-130 VAC or 127-184VDC 47-63Hz. >0.98 8% max. 1.4A max. 3.75kVAC / 1minute 1.8kVAC / 1minute 0.5kVAC / 1minute <0.75mA -1% to 5% 1.5s 150mVp-p max. Auto-Recovery Hiccup Mode 15V typ. 31V typ. 45V typ. 58V typ. Tcase 95°C ±10°C -20°C to +50°C( see graph) 75°C max. 20%-90% RH Non-Condensing -40°C to +80°C 10%-90% RH 10-500Hz, 2G, 60 Min. along X, Y and Z IP67 EN55015 FCC, Part 15 EN61000-3-2 Class C (≥75% load) EN61000-3-3 EN61000-4-2, 3, 4, 5, 6, 11 continued on next Page REV: 0/2015 RoHS 2011/65/EU 6/6 RACD100-PSE Note: All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Refer to Application Notes www.recom-power.com RACD100-PSE Series LIGHTLINE AC/DC-Converter Specifications J61347-1(H20), J61347-2-13(H21), J55015(H20) 222*68*39mm 1020g 250 x 10³ hours 70 x 10³ hours PSE Certification Dimension Weight MTBF using MIL-HDBK-217F (25°C) Design Lifetime The use of a circuit breaker with C-characteristic is recommended. Derating Curves Load Load 100% 100% 80% 80% 60% 60% 40% 40% 20% 20% -20 0 10 30 50 70 Ta=25°C 115 100 90 130 Input Voltage (VAC)60Hz Ambient Temperature (°C) Typical Characteristics Constant Voltage / Constant Current Curve RACD100-24 RACD100-12 CV Vout 12 (nom) RACD100-36 CV Vout (nom) 24 8.3 Iout 0 CC Vout (min) 14 0 CV Vout (nom) 48 CC Vout (min) 26 4.2 Iout CC Vout (min) 34 2.8 Iout 0 2.1 Iout 0 Maximum Number of LED drivers per circuit breakers Condition Circuit Breaker 115VAC, 1Ohm 90° phase angle Circuit Breaker Current Typ 10A 16A 20A 25A C 7 12 14 18 Package Style and Pinning Top View 222.0 11.4 7.0 AC/L (White) AC/N (Black) Earth (Green/Yellow) 10±3 300±20 8.9 PSEVCTF 1.25/3C 35±5 199.2 34.2 8.9 34.0 99.6 Tc 68.0 300±20 +V (Red) -V (Black) PSEVCTF 2.00/2C Side View 35±5 10±3 39.0 The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV: 0/2015 L-61 RACD100 -PSE Vout (min) 9 CV Vout (nom) 36 CC RACD100-48