Filename: tfs 92g.doc Version 2.0 Vectron International 27.08.2013 Filter specification TFS 92G 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 25 0 °C dBm 150 Ω || -33 pF 100 Ω || -42 pF Characteristics Remark: The reference level for the relative attenuation arel of the TFS 92G is the minimum of the pass band attenuation. This value is defined as the insertion loss ae. The nominal frequency fN is fixed at 92 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss ae 7,5 dB tolerance / limit max. 13 dB 92 MHz (reference level) Nominal frequency fN Passband PB Amplitude ripple in PB Relative attenuation 12 MHz fN 0,3 dB max. 1 dB 0,3 dB max. 1 dB ± 5 MHz arel fN - 5 MHz … fN + 5 MHz fN - 90 MHz ... fN - 40 fN ± 15 MHz 68 dB min. 45 dB fN ± 7.5 MHz MHz 19 dB min. 10 dB fN ± 15 MHz fN ± 40 MHz 48 dB min. 35 dB fN + 40 MHz fN + 200 MHz 52 dB min. 45 dB 70 ns max. 125 ns 11 dB min. 8 dB max. 10 dB Group delay ripple in PB GDR Return loss in PB Input power level Operating temperature range OTR -40 °C ... + 85°C Storage temperature Temperature coefficient of frequency - 45 °C ... + 85°C TCf **) -85 ppm/K *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions, do not hesitate to ask for an application note or contact our design team. **) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fcat(MHz). Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 92g.doc Version 2.0 Vectron International 27.08.2013 Filter specification TFS 92G 2/5 Filter characteristic 1.91 -1 1.79 -20 -2 1.67 -30 -3 1.55 -40 -4 1.43 -5 1.31 -6 1.19 -70 -7 1.07 -80 -8 0.95 -90 -9 0.83 -50 -60 -100 72 76 80 84 88 92 96 frequency in MHz 100 104 108 112 -10 82.11 84.11 86.11 88.11 90.11 92.11 94.11 frequency in MHz 96.11 98.11 100.11 delay in µs 0 -10 magnitude in dB magnitude in dB insertion loss: -7.59 dB 0 0.71 102.11 Construction and pin connection (All dimensions in mm) 1,9 +/- 0,2 TFS 92G ● D35 1 1,5 ±0,15 ±0,15 1 2,54 +/-0,2 +/- 0,2 6,50 13,30 2,54 2 3 4 5 11 6 8 Ground Ground Ground Ground Output Output RF Return Ground Ground Ground Ground Input Input RF Return / Ground Date code: D E F ... Year + week 2013 2014 2015 ±0,15 12 10 9 1 2 3 4 5 6 7 8 9 10 11 12 7 0,8 ±0,15 50 Ohm Test circuit L1 C1 11 12 L3 5 SAW 6 L2 1, 2,3,4, 7,8,9, 10 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 92g.doc Version 2.0 Vectron International 27.08.2013 Filter specification TFS 92G 3/5 Stability characteristics After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C /15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: twice max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 1700 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 24,00 +0,30/-0,10 Po : 4,00 ± 0,1 Do : 1,50 +0,1/0 E : 1,75 ± 0,10 F : 11,50 ± 0,10 G(min) : 0,60 P2 : 2,00 ± 0,1 P1 : 12,00 ± 0,1 D1(min) : 1,50 Ao : 7,10 ± 0,10 Bo : 13,90 ± 0,10 Ct : 21 ± 0,1 P1 t PIN Marker Po P2 W G Ct Bo F G E Do Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 24,4 +2/-0 W2(max) : 30,4 N(min) : 60 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 92g.doc Version 2.0 Vectron International 27.08.2013 Filter specification TFS 92G 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 92g.doc Vectron International Version 2.0 Filter specification 27.08.2013 TFS 92G 5/5 History : Version Reason of Changes Name Date 1.0 generating specification according to customer requirements Chilla 30.04.2013 1.1 changed insertion loss Chilla 08.05.2013 changed relative attenuation 1.2 changed relative attenuation Chilla 30.05.2013 2.0 created filter specification added terminating impedances added typical values added temperature coefficient of frequency added filter characteristic added test circuit Chilla 27.08.2013 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.