TFS140AU - Vectron International

Filename: tfs 140au.doc
Version 2.0
Vectron International
02.07.2009
Filter specification
TFS 140AU
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance: *
Input:
Output:
23
0
°C
dBm
103 Ω || -11 pF
120 Ω || -11 pF
Characteristics
Remark:
The nominal frequency fN is fixed at 140,0 MHz. The insertion loss ae is defined as loss value determined at fN. Reference level for the relative
attenuation arel of the TFS 140AU is the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the
20 dB filter attenuation level relative to the insertion loss ae. All specified data are met within the operating temperature range.
Data
typ. value
Insertion loss
(reference level)
ae
Nominal frequency
fN
-
Centre frequency
fC
140
MHz
PB
42
MHz
fN
dB
max.
1
MHz
MHz
max.
max.
49,6
65,0
dB
max.
1
dB
38
36
dB
dB
min.
min.
33
33
dB
dB
15
ns
max.
25
ns
-
max.
0
-
-40 °C ... + 85°C
Passband
0,3
Pass band ripple
dB
dB
43,4
54,7
… fN
±
18,6
arel
MHz
MHz ... fN
MHz ... fN
+
32,5
90,0
MHz
MHz
Relative attenuation
fN
fN
fN
+
100,0
32,5
dB
max.
20,0
140,0
dB
MHz
±
18,6
MHz
dB
BW
Bandwidth
2
33
18
tolerance / limit
Group delay ripple within PB
p-p
Input power level
Operating temperature range
OTR
-
Storage temperature range
Temperature coefficient of frequency
0,4
TCf **
-90
MHz
MHz
dBm
-55 °C ... + 80°C
ppm/K
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference
values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz)
Generated:
Checked / Approved:
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 140au.doc
Version 2.0
Vectron International
02.07.2009
Filter specification
TFS 140AU
2/5
0
0.736
-0.2
0.712
-10
-0.4
0.688
-15
-0.6
0.664
-0.8
0.64
-20
-25
-1
0.616
-1.2
0.592
-35
-1.4
0.568
-40
-1.6
0.544
-45
-1.8
0.52
-30
-50
70
84
98
112
126
140
154
frequency in MHz
168
182
196
-2
117
210
121.6
126.2
130.8
135.4
140 144.6
frequency in MHz
149.2
153.8
158.4
delay in µs
0
-5
magnitude in dB
magnitude in dB
Filter characteristic
0.496
163
Construction and pin connection
(All dimensions in mm)
TFS 140AU
●
X27
6,8Max.
13,6Max.
2,54 ±0,15
1,5
2,54 ±0,15
1 2 3 4
2,0Max.
1
12
5
11
6
Date code
10 9 8 7
1
2
3
4
5
6
7
8
9
10
11
12
Ground
Ground
Ground
Ground
Output
Output RF Return
Ground
Ground
Ground
Ground
Input
Input RF Return
Date code:
U
V
W
...
Year + week
2006
2007
2008
0,1
0,8
50 Ω Test circuit
L1
11
12
5
SAW
L2
6
C2
C1
1, 2, 3, 4, 7, 8, 9, 10
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 140au.doc
Version 2.0
Vectron International
02.07.2009
Filter specification
TFS 140AU
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or g respectively, 1 octave per min, 10 cycles per plan, 3 plans;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
This filter is RoHS compliant (2002/95/EG, 2005/618/EG)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
1700
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direction
Tape (all dimensions in mm)
W
: 24,00 +0,30/-0,10
Po
: 4,00 ± 0,1
Do
: 1,50 +0,1/-0
E
: 1,75 ± 0,10
F
: 11,50 ± 0,10
G(min)
: 0,60
P2
: 2,00 ± 0,1
P1
: 12,00 ± 0,1
D1(min)
: 1,50
Ao
: 7,10 ± 0,10
Bo
: 13,90 ± 0,10
Ct
: 21,5 ± 0,1
P1
Date Code
Po
Do
P2
W
G
Ct
Bo
F
G
E
t
Ko
Typ
PIN Marker
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 330
W1
: 24,4 +2/-0
W2(max) : 30,4
N(min)
: 60
C
: 13,0 +0,5/-0,2
A
C
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 140au.doc
Version 2.0
Vectron International
02.07.2009
Filter specification
TFS 140AU
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 140au.doc
Vectron International
Version 2.0
Filter specification
02.07.2009
TFS 140AU
5/5
History
Version
Reason of Changes
Name
Date
1.0
- Generation of development specification
Strehl
31.05.2006
1.1
- Add commentary to group delay ripple
Strehl
15.06.2006
1.2
- Created filter specification
- Added terminating impedances
- Changed max. group delay ripple
- Added typical values
- Changed relative attenuation
- Added temperature coefficient of frequency
- Added filter characteristic
- Added test circuit
Chilla
16.11.2006
2.0
- Changed operating temperature range
Chilla
02.07.2009
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.