Filename: tfs 115l.doc Version 1.2 Vectron International 28.05.2014 Filter specification TFS 115L 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 25 0 °C dBm 75 Ω ll -41pF 58 Ω ll -45pF Characteristics Remark: The reference level for the relative attenuation arel of the TFS115L is the minimum of the pass band attenuation. This value is defined as the insertion loss ae. The nominal frequency fN is fixed at 115 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss (reference level) Insertion loss within 2.5dB BW ae 5.4 ae + 2.5dB 7.9 tolerance / limit dB max. 9.5 max. 12 fN Nominal frequency 115 PB Passband fN 0.56 Pass band ripple dB max. ± dB dB MHz 3 MHz 0,8 dB arel MHz 0.56 MHz -57 dB min. 40 dB 11 MHz -52 dB min. 30 dB 7 MHz -25 dB min. 20 dB MHz … fN + 11 MHz -25 dB min. 20 dB MHz … fN + 15 MHz -41 dB min. 30 dB 15 MHz … fN + 29 MHz -51 dB min. 40 dB fN + 29 MHz … fN + 39 MHz -60 dB min. 50 dB fN + 137 MHz … fN + 147 MHz -75 dB min. 50 dB 71 ns max. 150 ns min. 30 dBm Relative attenuation fN - 3 MHz … fN + 3 fN - 27 MHz … fN - 15 fN - 15 MHz … fN - fN - 11 MHz … fN - fN + 7 fN + 11 fN + Group delay ripple in PB GDR max. - IIP3 2.5 dB Triple transit attenuation 39 dB min. 35 dB Return loss in PB 14 dB min. 10 dB Input power - max 10 dBm Operating temperature range OTR - 40 °C ... + 85°C - 55 °C ... + 85°C Operable temperature range - 45 °C ... + 85°C Storage temperature range Temperature coefficient of frequency TCf ** -94 ppm/K *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fcat(MHz). Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 115l.doc Version 1.2 Vectron International 28.05.2014 Filter specification TFS 115L 2/5 Filter characteristic 0.89 -1 0.854 -20 -2 0.818 -30 -3 0.782 -40 -4 0.746 -5 0.71 -50 -6 0.674 -70 -7 0.638 -80 -8 0.602 -90 -9 0.566 -60 -100 85 91 97 103 109 115 121 frequency in MHz 127 133 139 -10 104.92 145 106.92 108.92 110.92 112.92 114.92 116.92 frequency in MHz 118.92 120.92 122.92 delay in µs 0 -10 magnitude in dB magnitude in dB insertion loss: -5.40 dB 0 0.53 124.92 Construction and pin connection (All dimensions in mm) 1,9 + /- 0,2 TFS 115L ● D30 1 1,5 ± 0,15 ± 0,15 1 2,54 + /-0,2 + /- 0,2 6,50 13,30 2,54 2 12 5 11 6 10 9 8 Ground Ground Ground Ground Output Output RF Return Ground Ground Ground Ground Input Input RF Return / Ground Date code: D E F ... Year + week 2013 2014 2015 ± 0,15 4 3 1 2 3 4 5 6 7 8 9 10 11 12 7 0,8 ± 0,15 50 Ω Test circuit L1 C1 11 12 5 SAW 6 L3 C2 1,2,3,5,7,8,9,11 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 115l.doc Version 1.2 Vectron International 28.05.2014 Filter specification TFS 115L 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; ANSI/ESD S20.20-1999, class 1A for HBM This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 1700 min. 300 mm min. 500 mm min. 300 mm Pull Off Direc tion Tape (all dimensions in mm) W :24,00 +0,30/-0,10 Po :4,00 ± 0,1 Do :1,50 +0,1/-0 E :1,75 ± 0,10 F :11,50 ± 0,10 G(min) :0,60 P2 :2,00 ± 0,1 P1 :12,00 ± 0,1 D1(min) :1,50 Ao :7,10 ± 0,10 Bo :13,90 ± 0,10 Ct :21,5 ± 0,1 P1 t PIN Marker Po P2 W G Ct Bo F G E Do Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 :24,4 +2/-0 W2(max) :30,4 N(min) : 60 C :13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 115l.doc Version 1.2 Vectron International 28.05.2014 Filter specification TFS 115L 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 115l.doc Vectron International Version 1.2 Filter specification 28.05.2014 TFS 115L 5/5 History Version Reason of changes Name Date 1.0 Generation of development specification Chilla 25.07.2013 1.1 Added characteristic plots, typical values and 50Ω test circuit TCUK 26.11.2013 1.2 Added temperature coefficient TCUK 28.05.2014 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.