Filename: tfs 340.doc Version 1.2 Vectron International 19.12.2013 Filter specification TFS 340 1/5 Measurement condition Ambient temperature: Input power level: Input: Output: 23 0 50Ω 50Ω Source: Load: °C dBm 162Ω || -0.5pF 162Ω || -0.5pF Characteristics Remark: Reference level for the relative attenuation arel of the TFS340 is the minimum of the pass band attenuation amin. The minimum of the pass band attenuation amin is defined as the insertion loss ae. The centre frequency fC is the arithmetic mean value of the upper and lower frequencies at the 3dB filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 340MHz without tolerance. The given values for the relative attenuation arel and for the group delay ripple have to be reached at the frequencies given below even if the centre frequency fC is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fC. Data typ. value Insertion loss (Reference level) ae = amin 2.50 Nominal frequency fN - Centre frequency fc 340.0 dB fN fN fN fN fN 80.0 35.0 + 25.0 + 57.5 + 127.5 MHz ... fN MHz ... fN MHz ... fN MHz ... fN MHz ... fN Intermodulation max.3.0 340.0 MHz Pass band ripple fN ± 10 MHz Relative attenuation tolerance / limit dB MHz max. 3.0 dB**) min. min. min. min. min. dB dB dB dB dB arel - 100.0 - 55.0 + 57.5 + 82.5 + 152.5 MHz MHz MHz MHz MHz IP3 55 60 25 55 60 dB dB dB dB dB 50.0 30.0 20.0 40.0 57.0 - min. 20.0 dBm **) - max. 10.0 dBm VDC - max. 12.0 V Operating temperature range - - 25 °C ... + 75 °C Input power level Permissible DC voltage Temperature coefficient of frequency Tcf Storage temperature range -65 ppm/K - - 40 °C ... + 85 °C *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions, do not hesitate to ask for an application note or contact our design team. **) -3dB over fN ± 10MHz at ambient temperature (23°C). ***) modulation signals: fN + 1MHz and fN + 2MHz, each of 10dBm Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 340.doc Version 1.2 Vectron International 19.12.2013 Filter specification TFS 340 2/5 Filter characteristic insertion loss: -2.83 dB 0 -10 -0.5 -20 -1 -30 -1.5 -40 S21 in dB S21 in dB insertion loss: -2.83 dB 0 -50 -60 -2 -2.5 -3 -70 -3.5 -80 -4 -90 -4.5 -100 165 200 235 270 305 340 375 frequency in MHz 410 445 480 515 -5 325 328 331 334 337 340 343 frequency in MHz 346 349 352 355 Construction and pin connection (All dimensions in mm) 5 7 1 2 3 4 5 6 7 8 340 ● D51 3 5 7 0,1 1,1 1 2 3 4 5 6 7 8 Date code: D E F ... 1,1 120° 5 - 0,10 1,8 Max. 1 Date code 0,64 3 +0,15 1 Input Ground Ground Ground Output Ground Input Ground Ground Ground Ground Ground Output Ground Ground Ground Year + week 2013 2014 2015 2,54 50 Ω Test circuit 1 L1 5 L2 SAW C2 C1 2, 3, 4, 6, 7, 8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 340.doc Version 1.2 Vectron International 19.12.2013 Filter specification TFS 340 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10Hz to 500Hz, 0.35 mm or 5g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; ANSI/ESD S20.20-1999, class 0 for HBM This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direc tion Tape (all dimensions in mm) W : 12.00 Po : 4.00 Do : 1.50 E : 1.75 F : 5.50 G(min) : 0.75 P2 : 2.00 P1 : 8.00 D1(min) : 1.50 Ao : 5.30 Bo : 5.30 Ct : 9.2 ± 0.1 P1 t PIN Marker Po P2 W G Ct Bo F G E Do Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12.4 +2/-0 W2(max) : 18.4 N(min) : 50 C : 13.0 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 340.doc Version 1.2 Vectron International 19.12.2013 Filter specification TFS 340 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 340.doc Vectron International Version 1.2 Filter specification 19.12.2013 TFS 340 5/5 History Version Reason of Changes Name Date 1.0 - generate according customer requirement specification Dr. Sabah 02.12.2002 1.1 - filter specification, add of all typical values and terminating impedance Dr. Sabah 11.02.2003 1.2 - updating specification format and adding typical plots S.Springfeldt 19.12.2013 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.