Filename: tfs 216.doc Version 2.0 Vectron International 15.07.2009 Filter specification TFS 216 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: External Coil: 23 0 °C dBm 760 Ω ║ -1,8 pF 770 Ω ║ -1,4 pF 135 nH Characteristics Remark: The reference level for the relative attenuation arel of the TFS 216 is the minimum of the pass band attenuation. This value is defined as the insertion loss ae. The nominal frequency fN is fixed at 216,9 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss (reference level) ae 2,8 Nominal frequency fN 216,914 PB Passband dB ± ± 216 400 fN ± 600 fN fN + 30,0 3,0 216,9 fN ± 60,0 dB MHz kHz dB max. 2 kHz min. 120 1 14 43 57 72 53** 77 75 64 62 dB dB dB dB dB dB dB dB dB dB max. min. min. min. min. min. min. min. min. min. 2 10 40 50 50 45** 50 50 53 53 dB dB dB dB dB dB dB dB dB dB 0,9 µs max. 1,2 µs dB min. 10 dB - max. 10 dBm - - 40 °C ... + 85 °C - 40 °C ... + 85 °C 330 Relative attenuation fN fN fN 5 dB BW Bandwidth 2 max. MHz 1 Pass band ripple dB tolerance / limit … fN kHz … fN kHz … fN fN fN kHz … fN fN fN MHz … fN MHz … fN ± ± ± + ± + + 60 400 600 600 600 3 1,2 1,2 3,0 30,0 arel kHz kHz kHz kHz kHz MHz MHz MHz MHz MHz Group delay ripple within PB **** 13 Return loss within PB Input power level Operating temperature range Storage temperature range Frequency inversion temperature Temperature coefficient of frequency OTR TCf *** 26 -0,036 °C 2 ppm/K kHz - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) two narrow band distortions acceptable in total ***) ∆f(Hz) = TCf(ppm/K2) x (T-T0)2 x fTo(MHz) ****) value has to be achieved in any 42kHz segment of the passband Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 216.doc Version 2.0 Vectron International 15.07.2009 Filter specification TFS 216 2/5 Filter characteristic insertion loss: -3.17 dB 0 5.5 -1 5.25 -20 -2 5 -30 -3 4.75 -40 -4 4.5 -5 4.25 -6 4 -70 -7 3.75 -80 -8 3.5 -90 -9 magnitude in dB magnitude in dB -10 -50 -60 -100 206.9 208.9 210.9 212.9 214.9 216.9 218.9 frequency in MHz 220.9 222.9 224.9 3.25 -10 216.7 226.9 delay in µs 0 216.74 216.78 216.82 216.86 216.9 216.94 frequency in MHz 216.98 217.02 217.06 3 217.1 Construction and pin connection (All dimensions in mm) S 216 ● X28 3 Date code 2 Max. 1 1 5,2 Max. 2,54 ±0,2 7,2 Max. 2,54 ±0,2 1 1 2 3 4 5 6 7 8 9 10 11 12 Output Output Ground External Coil Ground Ground Input Input RF Return Ground Ground Ground Ground Date code: X A B ... Year + week 2009 2010 2011 0,80 50 Ω test circuit 1 7 L1 C1 8 L2 SAW 2 L4 4 3, 5, 6, 9, 10, 11, 12 C2 L3 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 216.doc Version 2.0 Vectron International 15.07.2009 Filter specification TFS 216 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2 HBM:250V; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 16,00 +0,3/-0,1 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 7,50 ± 0,1 G(min) : 0,75 P2 : 2,00 ± 0,1 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 5,40 ± 0,1 Bo : 7,60 ± 0,1 Ct : 13,5 ± 0,1 P1 Date Code Po Do P2 W G Ct Bo F G E t Ko Typ PIN Marker D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 16,4 +2/-0 W2(max) : 22,4 N(min) : 50 C : 13,0 +0,5/-0,2 A C N W 1 The minimum bending radius is 45 mm. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 216.doc Version 2.0 Vectron International 15.07.2009 Filter specification TFS 216 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 216.doc Vectron International Version 2.0 Filter specification 15.07.2009 TFS 216 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification Strehl 02.02.2009 1.1 - Add return loss - Change relative attenuation Strehl 16.02.2009 1.2 - Change definition of group delay ripple Martens 07.07.2009 2.0 - Change from development specification to filter specification - Add terminating impedance, typical values and filter characteristic Dr. Wall 15.07.2009 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.