Filename: tfs 1632.doc Version 1.4 Vectron International 09.06.2008 Filter specification TFS 1632 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 0 °C dBm 200 Ω || -0,48 pF 75 Ω Characteristics Remark: The nominal frequency fN is fixed at 1632,0 MHz. The insertion loss ae is defined as loss value determined at fN. Reference level for the relative attenuation arel of the TFS 1632 is the insertion loss ae. All specified data are met within the operating temperature range. Data typ. value ae Insertion loss (reference level) Nominal frequency Passband fN - PB 1,1 Pass band variation MHz MHz MHz MHz MHz MHz ... ... ... ... ... ... dB max. fN dB max. 3,0 ± dB 1632,0 MHz 20,0 MHz 2,0 dB arel Relative attenuation 0,3 860 1100 1724,6 2000 2250 2,2 tolerance / limit 860 1100 1539,7 2000 2250 6000 MHz MHz MHz MHz MHz MHz 62 54 45 40 44 28 dB dB dB dB dB dB min. min. min. min. min. min. 55 46 43 33 40 15 dB dB dB dB dB dB MHz 7 ns max. 15 ns Group delay ripple 1613,6 MHz ... 1650,3 Input VSWR within PB 2,0:1 max. 2,4 : 1 Output VSWR within PB 2,0:1 max. 2,4 : 1 min. 20 dB dBm 26 CMRR *** within PB dB Input power level - max. 10 Permissible DC voltage - max. 0 - - 30 °C ... + 80 °C - - 20 °C ... + 50 °C Operable temperature range Operating temperature range OTR - Storage temperature range Temperature coefficient of frequency TCf ** -46 V - 50 °C ... +125 °C ppm/K - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz) ***) CMRR: Common Mode Rejection Ratio Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1632.doc Version 1.4 Vectron International 09.06.2008 Filter specification TFS 1632 2/5 0 0.128 -10 -1 0.116 -20 -2 0.104 -30 -3 0.092 -40 -4 0.08 -5 0.068 -50 -6 0.056 -70 -7 0.044 -80 -8 0.032 -9 0.02 -60 -90 -100 38.2084 356.9668 675.7251 -10 1592 994.4834 1313.2417 1632 1950.7583 2269.5166 2588.2749 2907.0332 3225.7916 frequency in MHz 1600 1608 1616 1624 1632 1640 frequency in MHz 1648 1656 1664 delay in µs 0 magnitude in dB magnitude in dB Filter characteristic 0.008 1672 Construction and pin connection (All dimensions in mm) 5 6 4 H32 ● W24 1,2 Max. Ground Output Ground Input Ground Input Date code: W X A ... Year + week 2008 2009 2010 3 2 1 1 2 3 4 5 6 Date code 0,1 3 0,75 3 ±0,15 1,5 1 0,6 6 0,6 4 200 Ohm / 75 Ohm Test circuit 200Ω 75Ω 4 L1 6 SAW 2 1, 3, 5 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1632.doc Version 1.4 Vectron International 09.06.2008 Filter specification TFS 1632 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 9000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction P1 Tape (all dimensions in mm) W : 8,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 3,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 4,00 ± 0,1 D1(min) : 1,50 Ao : 3,25 ± 0,1 Bo : 3,25 ± 0,1 Ct : 5,5 ± 0,1 Date Code Do P2 W G Ct Bo F G E t Po Ko Typ PIN Marker D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 8,4 +1,5/-0 W2(max) : 14,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1632.doc Version 1.4 Vectron International 09.06.2008 Filter specification TFS 1632 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1632.doc Vectron International Version 1.4 Filter specification 09.06.2008 TFS 1632 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification Strehl 19.06.2007 1.1 - Change and add data Strehl 18.07.2007 1.2 - Change passband, passband variation - Change attenuation and OTR S. Channaa 08.02.2008 - Change attenuation, group delay ripple and vswr - Add typical values, filter characteristic, generation of filter specification S. Channaa 06.05.2008 - Correct construction Strehl 09.06.2008 1.3 1.4 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.