Filename: TFS1774.doc Version 1.1 Vectron International 05.02.2015 Filter specification TFS 1774 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: Input: Output: 23 0 °C dBm 50 50 Ω Ω Characteristics Remark: The reference level for the relative attenuation arel of the TFS1774 is the minimum attenuation in the passband. The maximum attenuation in the passband is defined as the insertion loss ae. The nominal frequency fN is fixed at 1774.9 MHz without any tolerance or limit. The values of relative attenuation arel are guaranteed over the whole operating temperature range. The frequency shift of the filter within the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss within PB ae 2.5 Nominal frequency fN - Passband PB Passband variation 0.6 Relative attenuation dB tolerance / limit max. fN dB max. dB min. 3.0 ± dB 1774.9 MHz 10.0 MHz 1.0 dB arel 10 MHz … 850 MHz 40 850 MHz … 900 MHz 40 dB min. 35 dB 900 MHz … 1350 MHz 40 dB min. 20 dB 1350 MHz … 1420 MHz 42 dB min. 40 dB 1420 MHz … 1510 MHz 44 dB min. 20 dB 1510 MHz … 1710 MHz 33 dB min. 5 dB 1835 MHz … 1855 MHz 55 dB min. 5 dB 1855 MHz … 1885 MHz 56 dB min. 10 dB 1915 MHz … 2690 MHz 38 dB min. 10 dB 2690 MHz … 6000 MHz Absolute group delay within PB Group delay ripple within PB Return loss within PB Input power level within PB * Operating temperature range OTR Storage temperature range Temperature coefficient of frequency *) 20dBm continuous input power over life time; **) ∆fc(Hz) = Tcf (ppm/K) x (T - To) x fCAT (MHz) TCf ** 20 dB 17 dB min. 10 dB 20 ns max. 100 ns 5 ns max. 40 ns 12 dB min. 10 dB max. 20 dBm - - 40 °C ... + 85°C - - 40 °C ... + 85°C -42 ppm/K 23dBm for duty cycle 1/10 over life time Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1774.doc Version 1.1 Vectron International 05.02.2015 Filter specification TFS 1774 2/5 Filter characteristic 0 0 0.12 -5 0.1 -10 0.08 -15 0.06 -20 0.04 -25 0.02 -10 S21 in dB GDR in µs S21 in dB -20 -30 -40 1730 1745 1760 1775 1790 frequency in MHz 1805 -50 1820 0 1000 2000 3000 frequency in MHz 4000 5000 6000 Construction and pin connection (All dimensions in mm) 6 5 4 3 2 3+/-0.15 1 0 6 Date code: F G H ... Year + week 2015 2016 2017 3 0.30 x 0.30 .3 R0 Ground Input Ground Ground Output Ground Date code 0.75+/-0.15 1 0.90+/-0.10 K74 ● F06 1 2 3 4 5 6 4 0.60+/-0.13 0.60+/-0.13 50 Ω Test circuit L1 2 5 L2 SAW 1, 3, 4, 6 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1774.doc Version 1.1 Vectron International 05.02.2015 Filter specification TFS 1774 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions, see page 4: "Air reflow temperature conditions" This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 8,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 3,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 4,00 ± 0,1 D1(min) : 1,50 Ao : 3,25 ± 0,1 Bo : 3,25 ± 0,1 Ct : 5,3 ± 0,1 P1 t Po P2 W G Ct Bo F G E Do PIN Marker Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 or 180 W1 : 8,4 +1,5/-0 W2(max) : 14,4 N(min) : 60 C : 13,0 ± 0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1774.doc Version 1.1 Vectron International 05.02.2015 Filter specification TFS 1774 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1774.doc Vectron International Version 1.1 Filter specification 05.02.2015 TFS 1774 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification A. Molke 13.10.2014 1.1 - Change from development spec to filter spec - Typical values added - Filter characteristic added A. Molke 05.02.2015 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.