Filename: tfs 2533.doc Version 2.1 Vectron International 07.01.2014 Filter specification TFS 2533 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: Source: Load: 23 0 °C dBm 27,22 Ω || -0,32 pF 27,22 Ω || -0,32 pF 50 Ω 50 Ω Characteristics Remark: The maximum attenuation in the pass band is defined as the insertion loss. The nominal frequency fN is fixed at 2533 MHz without any tolerance or limit. The values of absolute attenuation aabs are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss amax Nominal frequency Passband Pass band ripple 0,3 2400 fN - PB - in an arbitrary 1,25 MHz segment within PB Absolute attenuation 2,9 0,05 dB tolerance / limit max. fN dB max. 3,5 ± dB 2533,0 MHz 33,0 MHz 0,5 dB aabs MHz … 2400 MHz 32 dB min. 25 dB MHz … 2440 MHz 21 dB min. 10 dB 2620 MHz … 2630 MHz 37 dB min. 23 dB 2630 MHz … 2686 MHz 37 dB min. 35 dB 2686 MHz … 3250 MHz 29 dB min. 25 dB 3250 MHz … 5132 MHz 11 dB min. 5 dB VSWR within PB 1,6 : 1 max. Input power level within PB - max. - - 30 °C ... + 85 °C Operating temperature range OTR Storage temperature range Temperature coefficient of frequency TCf ** - 44 1,9 : 1 5 dBm - 40 °C ... + 85 °C ppm/K - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz). Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 2533.doc Version 2.1 Vectron International 07.01.2014 Filter specification TFS 2533 2/5 0 -1 -10 -2 -15 -3 -20 -4 -25 -6 -35 -7 -40 -8 -45 -9 500 1000 1500 2000 2500 frequency in MHz 3000 3500 4000 4500 -10 2463 5000 6 -5 -30 -50 9 VSW R 0 -5 m a g nitud e in d B m ag n itu d e in d B Filter characteristic 3 2477 2491 2505 2519 2533 frequency in MHz 2547 2561 2575 2589 0 2603 Construction and pin connection (All dimensions in mm) 5 6 4 1,2 Max. X33 ● E02 1 2 1 2 3 4 5 6 Ground Input Ground Ground Output Ground Date code: E F G ... Year + week 2014 2015 2016 3 Date code 3 0,75 3,0 +/-0,15 0,30X0,30 1 6 0,6 4 0,6 50 Ω Test circuit L1 2 5 L2 SAW C2 C1 1, 3, 4, 6 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 2533.doc Version 2.1 Vectron International 07.01.2014 Filter specification TFS 2533 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0.35 mm or g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions, see page 4: "Air reflow temperature conditions" This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exeption of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters peer reel: reel of empty components at start: reel of empty components at start including leader: trailer: 9000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 8,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 3,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 4,00 ± 0,1 D1(min) : 1,50 Ao : 3,25 ± 0,1 Bo : 3,25 ± 0,1 Ct : 5,5 ± 0,1 P1 Date Code t Po P2 W G Ct Bo F G E Do Ko Typ PIN Marker D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 8,4 +1,5/-0 W2(max) : 14,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 2533.doc Version 2.1 Vectron International 07.01.2014 Filter specification TFS 2533 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 2533.doc Vectron International Version 2.1 Filter specification 07.01.2014 TFS 2533 5/5 History Version Reason of changes Name Date 1.0 - Generation of development specification Roizengaft 12.12.2003 1.1 - change package (length of pin 1) - change matching circuit configuration - change packing (tape and reel) Noack 04.06.2004 - changing absolute attenuation - changing VSWR Noack 24.06.2004 Channaa 25.10.2005 1.2 1.3 - Add typical values, terminating impedances and filter characteristic - Changed test circuit and generation of filter specification - Generation of filter specification 1.4 - Changed absolute attenuation because of new customer requirement (0.3 …2400MHz & 2620 …2686MHz) Noack 10.11.2008 - Change of input power requirement - Relaxation of the outer limit line (@3250MHz…5132MHz) - Updating typical values S.Springfeldt 23.04.2010 - Maximum input power updated Kortenbeutel 07.01.2014 2.0 2.1 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.