Filename: tfs 350k.doc Version 2.2 Vectron International 18.03.2013 Filter specification TFS 350K 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 0 °C dBm 125 Ω || -5.5 pF 200 Ω || -7 pF Characteristics Remark: The reference level for the relative attenuation arel of the TFS350K is the minimum of the pass band attenuation. This value is defined as the insertion loss ae. The nominal frequency fN is fixed at 350,0 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss (reference level) ae Nominal frequency fN PB Passband 13,4 max. 14,5 350,0 80,4 0,5 Pass band ripple dB tolerance / limit MHz fN ± 37,5 1,0 dB MHz MHz dB max. dB MHz min. 75 MHz MHz max. 125 MHz Bandwidth 80,4 1 dB 106 40 dB MHz … fN + 37,5 arel MHz dB max. MHz … fN - 62,5 MHz 46 dB min. 40 dB 51 MHz 30 dB min. 25 dB 62,5 dB Relative attenuation fN fN - 37,5 100 0,6 1,0 dB fN - 62,5 MHz … fN - fN + 51 MHz … fN + MHz 30 dB min. 25 fN + 62,5 MHz … fN + 100 MHz 42 dB min. 40 dB MHz … fN + 2650 MHz 55 dB min. 50 dB fN + 100 0,27 Absolute group delay Group delay ripple within PB Return loss within PB IIP3 ** µs max. 16 ns max. 10 dB 41 dBm Input power level Operating temperature range OTR µs ns min. 7 dB min. 40 dBm max. 10 dBm - 30 °C ... + 60°C - 45 °C ... + 85°C Storage temperature range Temperature coefficient of frequency 0,5 100 TCf *** -91 ppm/K *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) fin1= 330MHz; fin2= 340MHz; Pin= 0dBm fmeasurement = 320MHz ***) ∆fc(Hz) = Tcf(ppm/K) x (T - To) x fCAT (MHz). Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 350k.doc Version 2.2 Vectron International 18.03.2013 Filter specification TFS 350K 2/5 Filter characteristic 0 0 1 -0.4 0.9 -0.8 0.8 -1.2 0.7 -1.6 0.6 magnitude in dB magnitude in dB -20 -30 -40 -50 -2 0.5 -2.4 0.4 -2.8 0.3 -3.2 0.2 -3.6 0.1 delay in µs -10 -60 -70 250 270 290 310 330 350 frequency in MHz 370 390 410 430 450 -4 300 310 320 330 340 350 frequency in MHz 360 370 380 390 0 400 Construction and pin connection (All dimensions in mm) 7 SQ 3,81 +0,2/-0,1 5 350K ● B42 1 3 Date code: B C D ... Year + week 2011 2012 2013 0,1 7 0,6 12 0% % d 3 1,78 2,54 1 Ground Output or Ground Output Ground Ground Input or Ground Input Ground 1,2 Max. Date code 1 2 3 4 5 6 7 8 5 1,78 Test circuit 7 L1 200 Ω C1 6 3 SAW L1 2 200 Ω C1 1, 4,5,8 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 350k.doc Version 2.2 Vectron International 18.03.2013 Filter specification TFS 350K 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2 HBM:250V; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 12,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 5,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 4,30 ± 0,1 Bo : 4,30 ± 0,1 Ct : 9,2 ± 0,1 P1 t Po P2 W G Ct Bo F G E Do PIN Marker Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 350k.doc Version 2.2 Vectron International 18.03.2013 Filter specification TFS 350K 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 350k.doc Vectron International Version 2.2 Filter specification 18.03.2013 TFS 350K 5/5 History Version Reason of Changes 1.0 - Generation of development specification Chilla 06.01.2011 2.0 - Created filter specification - Added terminating impedance - Added typical values - Added filter characteristic - Added test circuit - Changed packing - Attenuation updated Chilla 14.10.2011 2.1 - IIP3 updated Chilla 15.02.2012 2.2 - 1dB bandwidth corrected - Changed test circuit / pin connection Chilla 18.03.2013 Name Date Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.