Filename: tfs 175k.doc Version 3.0 Vectron International 13.02.2013 Filter specification TFS 175K 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 0 °C dBm 251 Ω || -12.7 pF 203 Ω || -16.6 pF Characteristics Remark: The reference level for the relative attenuation arel of the TFS175K is the minimum of the pass band attenuation. This value is defined as the insertion loss ae. The nominal frequency fN is fixed at 175 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss (reference level) ae Nominal frequency fN 14,8 dB max. 16 175 PB Passband tolerance / limit fN 0,4 Pass band ripple ± 18,5 dB MHz MHz dB max. 2 dB MHz min. 37 dB max. 3 dB Bandwidth 41,6 3 dB MHz MHz … fN + 18,5 arel MHz 60 MHz … fN - 50 MHz 55 dB min. 35 dB 50 MHz … fN - 31 MHz 46 dB min. 30 dB fN - 31 MHz … fN - 24 MHz 9 dB min. 5 dB fN + 24 MHz … fN + 31 MHz 6 dB min. 5 dB fN + 31 MHz … fN + 50 MHz 37 dB min. 30 dB fN + 50 MHz … fN + 60 MHz 39 dB min. 35 dB 7 ns max. "9 ns max. "2,5 ns min. 6 dB max. 15 Relative attenuation fN - 18,5 fN fN - 1,6 GDR Group delay ripple in PB *) Group delay variation (unit to unit) *), **) 7.5 Return loss within PB dB Input power level Operating temperature range OTR - 40 °C ... + 85°C - 45 °C ... + 85°C Storage temperature range Temperature coefficient of frequency dBm TCf ****) -99 ppm/K *) time gating window 0 … 0.5µs **) Measured at centre frequency, and averaged value to account for unit to unit variation and different bandwidth variants ***) ∆fc(Hz) = Tcf(ppm/K) x (T - To) x fCAT (MHz). Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 175k.doc Version 3.0 Vectron International 13.02.2013 Filter specification TFS 175K 2/5 Filter characteristic 0 -10 -1 0.2452 -20 -2 0.2404 -30 -3 0.2356 -40 -4 0.2308 -5 0.226 -60 -6 0.2212 -70 -7 0.2164 -80 -8 0.2116 -9 0.2068 -50 -90 -100 125 135 145 155 165 175 185 frequency in MHz 195 205 215 225 -10 150 0.25 155 160 165 170 175 frequency in MHz 180 185 190 195 delay in µs magnitude in dB magnitude in dB insertion loss: -14.77 dB 0 0.202 200 Construction and pin connection (All dimensions in mm) 7 5 S175K ● D07 3 7 5 0,1 1,1 120° +0,15 1,1 Date code: D E F ... Year + week 2013 2014 2015 1,8 Max. 1 Date code Ground Output 2 Output 1 Ground Ground Input 2 Input 1 Ground 0,64 3 5 - 0,10 1 1 2 3 4 5 6 7 8 2,54 50 Ω Test circuit L1 1:4 7 L3 L2 R1 3 SAW 6 R2 2 L3 L6 1:4 L4 1,4,5,8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 175k.doc Version 3.0 Vectron International 13.02.2013 Filter specification TFS 175K 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2 HBM:250V; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 12,00 Po : 4,00 Do : 1,50 E : 1,75 F : 5,50 G(min) : 0,75 P2 : 2,00 P1 : 8,00 D1(min) : 1,50 Ao : 5,30 Bo : 5,30 Ct : 9,2 ± 0,1 P1 t Po P2 W G Ct Bo F G E Do PIN Marker Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 175k.doc Version 3.0 Vectron International 13.02.2013 Filter specification TFS 175K 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 175k.doc Vectron International Version 3.0 Filter specification 13.02.2013 TFS 175K 5/5 History Version Reason of Changes 1.0 - Generation of development specification Chilla 09.07.2011 2.0 - Added time gating window - Removed triple transit level and triple transit delay Chilla 02.11.2012 3.0 - Created filter specification - Added terminating impedance - Added typical values - Added filter characteristic - Added test circuit - Changed packing Chilla 13.02.2013 Name Date Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.