Filename: tfs 500.doc Version 1.5 Vectron International 17.06.2014 Filter specification TFS 500 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: External Coil: 23 0 °C dBm 415 Ω || -1 pF 415 Ω || -1 pF 33 nH Characteristics Remark: The reference level for the relative attenuation arel of the TFS 500 is the minimum of the pass band attenuation. This value is defined as the insertion loss ae. The nominal frequency fN is fixed at 500,0 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss (reference level) ae Nominal frequency fN PB Passband Relative attenuation + 100 90 60 1 MHz MHz MHz MHz 390 1,3 Pass band variation fN fN fN fN 4,4 … … … … fN fN fN fN + 90 60 1 100 arel MHz MHz MHz MHz OTR Storage temperature range Frequency inversion temperature Temperature coefficient of frequency TCf ** max. 5,0 ± MHz 0,1 MHz 2,0 dB fN dB max. dB dB dB dB min. min. min. min. 40 38 40 40 max. 0 - - 40 °C …+ 85°C - - 40 °C ... + 85°C 41 °C - 0,036 ppm/K2 dB 500,0 kHz - Input power level Operating temperature range 48 42 47 42 dB tolerance / limit dB dB dB dB dBm *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆fc(Hz) = TCf(ppm/K2) x (T - To)2 x fTo (MHz). Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 500.doc Version 1.5 Vectron International 17.06.2014 Filter specification TFS 500 2/5 0 -1 6.28 -20 -2 5.56 -30 -3 4.84 -4 4.12 -5 3.4 -6 2.68 -70 -7 1.96 -80 -8 1.24 -90 -9 0.52 -40 -50 -60 -100 495 496 497 498 499 500 501 frequency in MHz 502 503 504 505 -10 499.5 7 499.6 499.7 499.8 499.9 500 500.1 frequency in MHz 500.2 500.3 500.4 delay in µs 0 -10 magnitude in dB magnitude in dB Filter characteristic -0.2 500.5 Construction and pin connection (All dimensions in mm) 7 500 ● U08 1 SQ 3,81 +0,2/-0,1 5 3 1 2 3 4 5 6 7 8 Input Input RF Return External Coil Ground Output Output RF Return Ground Ground Date code: T U V ... Year + week 2005 2006 2007 7 5 0,1 12 0% 0,6 % d 3 1,78 2,54 1 1,2 Max. Date code 1,78 50 Ω Test circuit 5 1 3 2, 4, 6, 7, 8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 500.doc Version 1.5 Vectron International 17.06.2014 Filter specification TFS 500 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0.35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions, see page 4: "Air reflow temperature conditions" ANSI/ESD S20.20-1999, class 1A for HBM This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 12,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 5,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 4,30 ± 0,1 Bo : 4,30 ± 0,1 Ct : 9,2 ± 0,1 P1 t Po P2 W G Ct Bo F G E Do PIN Marker Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 or 180 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 500.doc Version 1.5 Vectron International 17.06.2014 Filter specification TFS 500 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 500.doc Vectron International Version 1.5 Filter specification 17.06.2014 TFS 500 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification Strehl 10.11.2005 1.1 - Add operating temperature range - Add frequency inversion temperature Channaa 21.11.2005 1.2 - Add typical values - Add filter characteristic - Add test circuit - Add terminating impedances Martens 23.02.2006 1.3 - Change from development specification to filter specification - Change relative attenuation Alawneh 28.04.2006 1.4 - Updated header and footer to current standards Raura 08.11.2012 1.5 - Change Input power level - Update Reel dimensions - Update Stability characteristics, reliability - Update Filter characteristic - Add ESD Bonnen 17.06.2014 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.