Filename: tfs 200n.doc Version 1.2 Vectron International 14.02.2012 Filter specification TFS 200N 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 25 °C 0 " 2 dBm 134 Ω || -26 pF 134 Ω || -26 pF Characteristics Remark: The reference level for the relative attenuation arel of the filter is the minimum of the pass band attenuation. This value is defined as the insertion loss ae. The nominal frequency fN is fixed at 200 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. typ. value tolerance / limit Data ae Insertion loss 11,5 dB max. 13 dB (reference level) fN Nominal frequency PB Passband Pass band ripple Relative attenuation fN fN ± fN ± 12 25 … fN ± MHz ... fN ± MHz ... fN ± 7,5 25 50 Group delay ripple in PB arel MHz MHz MHz GDR Triple transit signal attenuation 200 17,4 MHz fN 0,4 dB 0.4 40 50 7,5 MHz max. 0,9 dB dB dB dB max. min. min. 0,9 30 45 dB dB dB 55 ns max. 120 ns 39 dB min. 35 dB max. 10 dBm Input power level Operating temperature range OTR -40 °C ... + 85°C - 45 °C ... + 85°C Storage temperature *) ± -30 °C ... + 70°C Operable temperature range Temperature coefficient of frequency MHz TCf ** -19 ppm/K The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions, do not hesitate to ask for an application note or contact our design team. Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 200n.doc Version 1.2 Vectron International 14.02.2012 Filter specification TFS 200N 2/5 0 -0.4 0.996 -16 -0.8 0.972 -24 -1.2 0.948 -32 -1.6 0.924 -40 -2 0.9 -2.4 0.876 -56 -2.8 0.852 -64 -3.2 0.828 -72 -3.6 0.804 -48 -80 100 120 140 160 180 200 220 frequency in MHz 240 260 280 -4 190.14 300 192.14 194.14 196.14 198.14 200.14 202.14 frequency in MHz 204.14 206.14 208.14 delay in µs 1.02 0 -8 magnitude in dB magnitude in dB Filter characteristic 0.78 210.14 Construction and pin connection (All dimensions in mm) TFS 200N ● C07 6,8Max. 13,6Max. 2,54 ±0,15 1,5 2,54 ±0,15 1 2 3 4 2,0Max. 1 12 5 11 6 Date code 10 9 8 7 1 2 3 4 5 6 7 8 9 10 11 12 Ground Ground Ground Ground Output Output RF Return Ground Ground Ground Ground Input Input RF Return Date code: C D E ... Year + week 2012 2013 2014 0,1 0,8 50 Ohm Test circuit 11 L1 12 5 SAW L2 L3 6 L4 1, 2, 3, 4, 7, 8, 9, 10 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 200n.doc Version 1.2 Vectron International 14.02.2012 Filter specification TFS 200N 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: twice max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: <MAXPIECESPERREEL> min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 24,00 +0,30/-0,10 Po : 4,00 ± 0,1 Do : 1,50 +0,1/0 E : 1,75 ± 0,10 F : 11,50 ± 0,10 G(min) : 0,60 P2 : 2,00 ± 0,1 P1 : 12,00 ± 0,1 D1(min) : 1,50 Ao : 7,10 ± 0,10 Bo : 13,90 ± 0,10 Ct : 21 ± 0,1 P1 t Po P2 W G Ct Bo F G E Do PIN Marker Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 24,4 +2/-0 W2(max) : 30,4 N(min) : 60 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 200n.doc Version 1.2 Vectron International 14.02.2012 Filter specification TFS 200N 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 200n.doc Vectron International Version 1.2 Filter specification 14.02.2012 TFS 200N 5/5 History Version Reason of Changes Name Date 1.0 Generation of specification according to customer requirements E. Chilla 30.08.2011 1.1 operable temperature range added E. Chilla 31.08.2011 1.2 Created filter specification Added terminating impedances Added typical values Added temperature coefficient of frequency Added filter characteristic Changed test circuit E. Chilla 14.02.2012 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.