TFS240S - Vectron International

Filename: tfs 240s.doc
Version 3.0
Vectron International
05.10.2010
Filter specification
TFS 240S
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance: *
Input:
Output:
22
0
°C
dBm
153 Ω || -11 pF
98 Ω || -16 pF
Characteristics
Remark:
The reference level for the relative attenuation arel of the TFS 240S is the minimum of the pass band attenuation. This value is defined as the insertion
loss ae. The nominal frequency fN is fixed at 240 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating
temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme.
Data
typ. value
ae
Insertion loss
(reference level)
fN
Nominal frequency
PB
Passband
Passband ripple
Passband ripple over any 10 kHz segment
fN
±
+
+
10,25
140
120
80
22
17
20
40
dB
max.
11
25,2
240,0
MHz
fN
0,3
0,1
dB
dB
max.
max.
0,6
dB
max.
dB
dB
dB
dB
dB
dB
dB
min.
min.
min.
min.
min.
min.
min.
±
dB
MHz
10,25 MHz
1,4
0,2
MHz
MHz
arel
Relative attenuation
fN
fN
fN
fN
fN
fN
fN
8.5
tolerance / limit
MHz … fN
+
MHz
MHz
MHz
MHz
MHz
MHz
MHz
fN
fN
fN
fN
-
120
80
22
19,5
MHz
MHz
MHz
MHz
… fN
… fN
+
+
40
260
MHz
MHz
…
…
…
…
10,25
MHz
60
55
46
44
26
41
42
0,46
Absolute group delay
Group delay ripple within PB
Phase linearity within PB
p-p
Triple transit response suppression
1,4
40
50
40
42
15
35
40
µs
max.
2
µs
40
ns
max.
100
ns
13
deg
max.
15
deg
42
dB
min.
35 **
dB
VSWR
1,4:1
max.
Input power level
-
max.
-
- 40 °C ... + 85°C
Operating temperature range
OTR
-
Storage temperature range
Temperature coefficient of frequency
TCf ***
dB
dB
dB
dB
dB
dB
dB
dB
-88
2:1
15
dBm
- 40 °C ... + 85°C
ppm/K
-
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference
values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) target is 40 dB
***) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz)
Generated:
Checked / Approved:
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 240s.doc
Version 3.0
Vectron International
05.10.2010
Filter specification
TFS 240S
2/5
Filter characteristic
0
-10
-0.4
1.03
-20
-0.8
0.955
-30
-1.2
0.88
-40
-1.6
0.805
-50
-60
1.105
0.73
-2
-2.4
0.655
-70
-2.8
0.58
-80
-3.2
0.505
-90
-3.6
0.43
-100
190
200
210
220
230 240 250
frequency in MHz
260
270
280
-4
226
290
228.8
231.6
234.4
237.2
240
242.8
frequency in MHz
245.6
248.4
251.2
delay in µs
magnitude in dB
magnitude in dB
insertion loss: -8.46 dB
0
0.355
254
Construction and pin connection
(All dimensions in mm)
S 240S
●
A41
1
2
3
4
5
6
7
8
9
10
Ground
Ground
Ground
Output
Output RF Return
Ground
Ground
Ground
Input
Input RF Return
Date code:
A
B
C
...
Year + week
2010
2011
2012
Date code
50 Ohm Test circuit
L1
4
9
10
SAW
C1
5
L2
C2
1, 2, 3, 6, 7, 8
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 240s.doc
Version 3.0
Vectron International
05.10.2010
Filter specification
TFS 240S
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
This filter is RoHS compliant (2002/95/EG, 2005/618/EG)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
3000
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direction
P1
Tape (all dimensions in mm)
W
: 16,00 ± 0,3
Po
: 4,00 ± 0,1
Do
: 1,50 +0,1/-0
E
: 1,75 ± 0,1
F
: 7,50 ± 0,1
G(min)
: 0,60
P2
: 2,00 ± 0,1
P1
: 8,00 ± 0,1
D1(min)
: 1,50
Ao
: 5,50 ± 0,1
Bo
: 7,50 ± 0,1
Ct
: 13,5 ± 0,1
Date Code
Po
Do
P2
W
G
Ct
Bo
F
G
E
t
Ko
Typ
PIN Marker
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 330
W1
: 16,4 +2/-0
W2(max) : 22,4
N(min)
: 50
C
: 13,0 +0,5/-0,2
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 240s.doc
Version 3.0
Vectron International
05.10.2010
Filter specification
TFS 240S
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 240s.doc
Vectron International
Version 3.0
Filter specification
05.10.2010
TFS 240S
5/5
History
Version
Reason of Changes
Name
Date
1.0
- Generation of development specification
Alawneh
05.05.2006
1.1
- Change data
Strehl
15.06.2006
1.2
- Created filter specification
- Added terminating impedances
- Added typical values
- Added temperature coefficient of frequency
- Added filter characteristic
- Changed construction
- Added test circuit
- Changed packing
Chilla
04.01.2007
2.0
- Changed relative attenuation
Chilla
09.11.2009
3.0
- Changed insertion loss
- Changed relative attenuation
Chilla
05.10.2010
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.