Filename: TFS110W.doc Version 1.4 Vectron International 26.03.2014 Filter specification TFS 110W 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 25 0 °C dBm 297 Ω || -23.3 pF 315 Ω || -24.6 pF Characteristics Remark: The reference level for the relative attenuation arel of the TFS 110W is the minimum of the pass band attenuation. This value is defined as the insertion loss ae. The nominal frequency fN is fixed at 110.592 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss (reference level) ae Nominal frequency fN Centre frequency fC Passband dB 4.5 dB 110.592 MHz MHz fN - Relative attenuation max. 110.592 PB Pass band ripple fN 3.5 tolerance / limit max. ± 280 kHz 3 dB arel … fN ± 0.280 MHz fN ± 1.150 MHz … fN fN ± 1.728 MHz … fN fN + 3.456 MHz … fN fN 3.456 MHz … fN 5.184 MHz fN fN 5.184 MHz … fN Group delay ripple within PB ± ± + - 1.728 3.456 5.184 5.184 1 dB max. 3 dB 18 35 45 49 53 50 100 dB dB dB dB dB dB ns min. min. min. min. min. min. max. 10 30 40 45 50 40 700 dB dB dB dB dB dB ns Input power level max. 10 Permissible DC voltage max. 3 - MHz MHz MHz MHz 15.000 MHz p-p Operating temperature range - - 20 °C ... + 70°C Operable temperature range - - 40 °C ... + 85°C Storage temperature range - - 40 °C ... + 85°C Temperature coefficient of frequency OTR TCf ** -19 dBm V ppm/K *) The terminating impedances depend on parasites and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz). Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS110W.doc Version 1.4 Vectron International 26.03.2014 Filter specification TFS 110W 2/5 0 5.58 -1 5.04 -12 -2 4.5 -18 -3 3.96 -24 -4 3.42 -5 2.88 -6 2.34 -42 -7 1.8 -48 -8 1.26 -54 -9 0.72 -30 -36 -60 100.6 102.6 104.6 106.6 108.6 110.6 112.6 frequency in MHz 114.6 116.6 118.6 -10 109.85 120.6 110 110.15 110.3 110.45 110.6 110.75 frequency in MHz 110.9 111.05 111.2 delay in µs 0 -6 magnitude in dB magnitude in dB Filter characteristic 0.18 111.35 Construction and pin connection (All dimensions in mm) S 110W ● E41 Date code 1 2 3 4 5 6 7 8 9 10 Ground Ground Ground Output RF Return Output Ground Ground Ground Input RF Return Input Date code: E F G ... Year + week 2014 2015 2016 50 Ohm Test circuit 10 L1 9 5 SAW L2 L3 4 L4 1, 2, 3, 6, 7, 8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS110W.doc Version 1.4 Vectron International 26.03.2014 Filter specification TFS 110W 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; ANSI/ESD S20.20-1999, class 1A for HBM This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters peer reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direc tion Tape (all dimensions in mm) W : 16.00 ± 0.3 Po : 4.00 ± 0.1 Do : 1.50 +0.1/-0 E : 1.75 ± 0.1 F : 7.50 ± 0.1 G(min) : 0.60 P2 : 2.00 ± 0.1 P1 : 8.00 ± 0.1 D1(min) : 1.50 Ao : 5.50 ± 0.1 Bo : 7.50 ± 0.1 Ct : 13.5 ± 0.1 P1 Da te Cod e t Po P2 W G Ct Bo F G E Do Ko Typ PIN Marker D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 16.4 +2/-0 W2(max) : 22.4 N(min) : 50 C : 13.0 +0.5/-0.2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS110W.doc Version 1.4 Vectron International 26.03.2014 Filter specification TFS 110W 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS110W.doc Vectron International Version 1.4 Filter specification 26.03.2014 TFS 110W 5/5 History Version Reason of Changes Name Date 1.0 - generation of development specification Strehl 10.06.2005 1.1 - change pass band and relative attenuation Strehl 13.07.2005 1.2 - terminating impedance (preliminary value), typical values and filter characteristic added - matching configuration changed Pfeiffer 02.09.2005 1.3 - terminating impedance fixed - typical values and filter characteristic changed Pfeiffer 07.10.2005 1.4 - Input power level increased to 10dBm max, (was 0dBm). - Added operable temperature range -40°C ...+85°C. - Update headers and footers. - Update stability characteristics, reliability TCUK 26.03.2014 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.