TFS190 - Vectron International

Filename: TFS190.doc
Version 4.0
Vectron International
13.06.2013
Filter specification
TFS 190
1/5
Measurement Condition
Ambient Temperature:
Input Power Level:
Source impedance:
Load impedance:
Terminating impedances:
Input :
Output:
23 °C
0 dBm
50 Ω
50 Ω
310 Ω || -14.9 pF
460 Ω || -14.4 pF
Characteristics
Remark:
Reference level for the relative attenuation arel is the pass band attenuation a0 at nominal frequency. It is defined as the insertion loss ae. The
nominal frequency fN is fixed to 190.0 MHz. The given values for the insertion loss, the relative attenuation arel and the group delay ripple have to
be reached at the frequencies given below also if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the
operating temperature range and due to a production tolerance for the centre frequency fc.
Data
typ. Value
Limit
Insertion Loss
(Reference level)
ae = amin
8.1 dB
Nominal Frequency
fN
-
1 dB - Bandwidth
BW
5.0 MHz
min.
4.0 MHz
0.5 dB
max.
1
dB
dB
dB
dB
min.
min.
min.
35
40
45
dB
dB
dB
0.5 dB
max.
1
dB
dB
dB
dB
min.
min.
min.
34
38
45
dB
dB
dB
0.5 dB
max.
1
dB
max. 150
ns
Relative Attenuation
fN
... fN ±
arel
2.0 MHz
fN ± 5.0 MHz ... fN ± 10.0 MHz
fN ± 10.0 MHz ... fN ± 20.0 MHz
fN ± 20.0 MHz ... fN ± 100.0 MHz
38
45
52
Relative Attenuation over
arel
Extended Operating Temperature Range
fN
... fN ±
2.0 MHz
fN ± 5.0 MHz ... fN ± 10.0 MHz
fN ± 10.0 MHz ... fN ± 20.0 MHz
fN ± 20.0 MHz ... fN ± 100.0 MHz
38
45
52
Pass Band Ripple
fN ± 2.0 MHz
Group delay ripple
fN ± 2.0 MHz
Phase linearity
fN ± 2.00 MHz
120
max.
10
dB
190.0 MHz
ns
ϕ
Operating Temperature Range
Extended Operating Temperature Range
Storage Temperature Range
Temperature coefficient of frequency TCf*
4.5 °rms
-18 ppm/K-
max.
6.0 °rms
- 10 °C ... + 85 °C
- 20 °C ... + 85 °C
- 40 °C ... + 85 °C
-
*) ∆fc(Hz) = Tcf(ppm/K) x (T - To) x fN (MHz).
Generated:
Checked / approved:
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information
contained herein without notice. No liability is assumed as a result of their use or application. No
rights under any patent accompany the sale of any such product(s) or information.
Filename: TFS190.doc
Version 4.0
Vectron International
13.06.2013
Filter specification
TFS 190
Filter characteristic
Construction and pin connection
Datecode
S 190
N24
1
2
3
4
5
6
7
8
9
10
11
12
Date code:
D
E
F
Ground
Ground
Output RF Return
Output
Ground
Ground
Ground
Ground
Input RF Return
Input
Ground
Ground
Year + week
2013
2014
2015
50 Ω test circuit
Input
C1
L1
10
C2
4
C3
Output
C4
SAW
9
L2
3
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information
contained herein without notice. No liability is assumed as a result of their use or application. No
rights under any patent accompany the sale of any such product(s) or information.
2/5
Filename: TFS190.doc
Version 4.0
Vectron International
13.06.2013
Filter specification
TFS 190
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0.35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
5. ESD
-55 °C to 125°C / 15 min. each / 100cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2
HBM:250V;
This filter is RoHS compliant (2011/65/EU)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
3000
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direc tion
Tape (all dimensions in mm)
W
: 16.00 ± 0.3
Po
: 4.00 ± 0.1
Do
: 1.50 +0.1/-0
E
: 1.75 ± 0.1
F
: 7.50 ± 0.1
G(min)
: 0.60
P2
: 2.00 ± 0.1
P1
: 8.00 ± 0.1
D1(min)
: 1.50
Ao
: 5.50 ± 0.1
Bo
: 7.50 ± 0.1
Ct
: 13.5 ± 0.1
P1
t
Po
P2
W
G
Ct
Bo
F
G
E
Do
PIN Marker
Ko
Date Code
Typ
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 330
W1
: 12.4 +2/-0
W2(max) : 18.4
N(min)
: 50
C
: 13.0 +0.5/-0.2
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information
contained herein without notice. No liability is assumed as a result of their use or application. No
rights under any patent accompany the sale of any such product(s) or information.
Filename: TFS190.doc
Version 4.0
Vectron International
13.06.2013
Filter specification
TFS 190
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak
temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information
contained herein without notice. No liability is assumed as a result of their use or application. No
rights under any patent accompany the sale of any such product(s) or information.
4/5
Filename: TFS190.doc
Vectron International
Version 4.0
Filter specification
13.06.2013
TFS 190
5/5
History
Version
Name
Date
Development specification
1.0
new spec
Steiner
31.05.2000
2.0
Steiner
22.09.2000
filter specification
3.0
- typical values+terminating impedances, tape and reel dimensions, air reflow profile
added
Steiner
08.06.2001
4.0
Reason of Changes
- group delay ripple, phase ripple increased
- stopband attenuation decreased
- package fixed to 7x5mm
-Change to new format spec : added extended temperature range with relaxed
attenuation. Added filter characteristics
TCUK
13.06.2013
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information
contained herein without notice. No liability is assumed as a result of their use or application. No
rights under any patent accompany the sale of any such product(s) or information.