FCHM cynergycomponents Hydromatic Pump Control Module Use To maintain and control water pressure, within a pumped system, for the supply to industrial processes and heating systems. Ensures constant flow and pressure to allow optimum performance of gas boilers or heaters, while preventing cycling and consequent temperature variations in the various appliances. Description A compact unit, which combines all the functions of a complete pressurising system, ie. Pressure Switch, Dry Running cut-out, Control Panel, Pressure Reservoir and Non-return Valve. The system employs a hydraulic chamber, equipped with a damping system to protect against water hammer, and a patented electromechanical control board, to be connected to 240Vac power source, with an internal 24V secondary circuit. Compared with conventional systems this is not only more compact, but easier and quicker to install, and makes for significant energy savings and reduced pump wear. It is also maintenance free, as the pressurisation unit does not require precharging with air. This system combines the versatility and control of conventional pressure switches with the advantages of pressure/flow switches. Avoids the need for pressure reservoirs, along with their associated maintenance costs. • Start up pressure 1-3.5 bar, adjustable • Dry running cut out and foot valve • Visual Indication and manual reset for water circuit faults • Pressure gauge for easy set up • Auxiliary fuse to protect pump control circuit SPECIFICATION Supply voltage 240Vac 50-60Hz Max operating power 2HP IP Rating 65 Max pressure 10 bar Max flow rate 100 l/min Max fluid temperature 60°C Max ambient temperature 60°C Minimum start-up pressure adjustable 1 - 3.5 bar Pump shutdown Flowrate 1.5L/min. Minimum output pressure(Pump max pressure) > = start-up ISO 9001C E R T I F IED Cynergy3 Components Ltd 7 Cobham Road Ferndown Industrial Estate Wimborne Dorset BH21 7PE Tel: +44 (0) 1202 897969 [email protected] www.cynergy3.com www.cynergy3.com © 2013 Cynergy3 Components, All Rights Reserved. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited. page 1 FCHM Hydromatic Pressure Regulator cynergycomponents WITHOUT FCHM Pressure Vessel Press Switch Min. Press Control Panel Dry Running Foot Valve WITH FCHM from Submersible pump ISO 9001C E R T I F IED www.cynergy3.com © 2013 Cynergy3 Components, All Rights Reserved. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited. page 2 FCHM cynergycomponents Hydromatic Pump Control Module Setting start up pressure Always install a pump that develops a maximum output pressure that is at least 1 bar greater than the required minimum start up pressure. If the head to be pumped is greater than 15m, it is necessary to increase the start up pressure setting e.g. 20m head requires at least 2.5 bar start up pressure, 25m head requires at least 3 bar start up pressure. To increase the start up pressure setting: Wiring for 1phase pumps up to 2HP Cynergy3 Components Ltd 7 Cobham Road Ferndown Industrial Estate Wimborne Dorset BH21 7PE Tel: +44 (0) 1202 897969 [email protected] www.cynergy3.com ISO 9001C E R T I F IED www.cynergy3.com © 2013 Cynergy3 Components, All Rights Reserved. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited. page 3 FCHM cynergycomponents Hydromatic Pump Control Module Wiring for 1phase pumps over 2HP Wiring for 3phase pumps Cynergy3 Components Ltd 7 Cobham Road Ferndown Industrial Estate Wimborne Dorset BH21 7PE Tel: +44 (0) 1202 897969 [email protected] www.cynergy3.com ISO 9001C E R T I F IED www.cynergy3.com © 2013 Cynergy3 Components, All Rights Reserved. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited. page 4