www.osram.com SubstiTUBE® Basic – ST8-HB4 ST8 Datasheet Innovative LED-lamp, LED easy and safe to use in CCG installations as direct retrofit. Energy saving potential of up to 52% by replacing 1.2 m T8 fluorescent tubes. Instant 100% light without flickering. No mercury. Applicable in warehouses, cold storage, supply rooms, corridors, industry, stairways, garages, indirect illumination etc; for applications with high operating hours. Technical operating data Product Color Colortemp. Lum. Flux [K] [lm] Cool Daylight 6500 K ST8-HB4-210-840 Cool White 4000 K 2100 ST8-HB4-190-830 Warm White 3000 K 1900 ST8-HB4-210-865 Voltage [V] / Frequency [Hz] Input current [A] Power [W] RadianceAngle [°] 230 V* 200 - 240 V 50 / 60 Hz 0.09 A 21 W 150° 2100 All Data are related to the entire lamp. Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. * Rated voltage Technical Features LED lamp in T8 shape with G13 socket Powerfactor > 0.9 Length excl. pins: 1200 mm max Weight: 260g Up to 40,000 h lifetime For operation at magnetic ballast Color Rendering Index (CRI) > 80 Direct Retrofit for CCG luminaires; replacement of lamp and included starter Overpower, overheat and short circuit protected No rewiring necessary at CCG High color homogeneity Extremely robust due to polycarbonate body RoHS-conformity, no mercury Switching cycles > 200.000 Fully integrated ECG complies to relevant standards Not for operation with ECG, not dimmable Energy Efficiency Class¹: A+ ¹ ST8-HB2 and ST8-HB5 in Coloretemp.. 3000K: Energy Efficiency Class A for operation with magnetic ballast ST8-HB4 – February 2015 Page 1 of 5 Minimum / Maximum ratings ST8-HB4 Operating temperature Tc Storage temperature Ts Ambient temperature Ta -20° … 75°C 80 -20° ... 80°C -20° ... 45°C Drawings Product l d ST8-HB4 1200 mm 27,5 mm ST8-HB4 – February 2015 Page 2 of 5 Safety and Application notes The SubstiTUBE® Basic must not be damaged or operated in a damaged condition. When operating with CCG, the included „SubstiTUBE® Start“ has to be inserted as well. If the conventional starter is not replaced the SubstiTUBE® Basic will start blinking. Switch off immediately, the SubstiTUBE® Basic can be damaged! Lamp suitable for 50 Hz or 60 Hz operation Lamp not suitable for high frequency operation Lamp not suitable for emergency operation Do not use SubstiTUBE® Basic in luminaires which do not have any starter or when the starter cannot be replaced. Not usable in luminaires with serial lamp connection i.e. more than one tube at one magnetic ballast (tandem circuitry). The SubstiTUBE® Basic emits light only with a limited angle, not like a fluorescent tube with 360°output. Due to the characteristic light distribution of the SubstiTUBE® Basic, the resulting luminaire light characteristic is likely to change. It is not guaranteed that e.g. standards for lighting at working places will be complied to after replacement. A photometric check of the installation is recommended. The effective energy savings depend on the efficiency of the luminaire setup to be replaced and should be considered individually in each case. Particularly magnetic ballast losses are reduced to ohmic losses and are normally only about 1 W. The SubstiTUBE® Value is protected according to IP20. Applications with external risk of moisture and dust can be served with an adequately protected luminaire. SubstiTUBE® Basic may also be driven directly on line voltage. In order to grant a safe operation mode please refer to the installation instructions for further information. Maximum amount of SubstiTUBE® Basic on one circuit breaker Circuit breaker 10 A (B type) Circuit breaker 16 A (B type) // // // // // // CCG CCG incl. comp. cap. Direct mains CCG CCG incl. comp. cap. Direct mains // // // // // // 71 28 73 113 45 116 Photobiological Safety of lamps and lamp systems according to IEC 62471. Risk Group: Exempt ST8-HB4 – February 2015 Page 3 of 5 Installation Instructions for CGG Make sure that the supply voltage is disconnected. Carefully remove the fluorescent tube and starter according to the lamp holder type. Insert SubstiTUBE® Basic and SubstiTUBE® Start properly. Below an example for typical lamp holder types is described Turn the conventional lamp 90° degrees and take it out of the socket. Remove the conventional starter by turning it. Insert and latch the SubstiTUBE® Start into starter socket. Insert SubstiTUBE® Basic into socket and locate into position by turning 90°. 90 Check light emission direction. Circuit diagram of a retrofitted CCG luminaire ST8-HB4 – February 2015 Page 4 of 5 Ordering guide Product name Light color EAN* ST8-HB4-210-865 Cool Daylight / 6500 K 4052899922525 ST8-HB4-210-840 Cool White / 4000 K 4052899922518 ST8-HB4-190-830 Warm White / 3000 K 4052899922501 S-Unit** 25 x 1 * EAN: Ordering number per single module ** S-Unit: Lamps per shipping unit Sales and Technical Support OSRAM GmbH Sales and technical support is given by the local OSRAM subsidiaries. On our world wide homepage all OSRAM subsidiaries are listed with complete address and phone numbers. Marcel-Breuer-Strasse 6 D - 80807 München Germany www.osram.com +49 (0)89 6213-0 Further Information Downloads: Eulumdat /IES files, CE declaration ST8-HB4 – February 2015 Page 5 of 5 www.osram.com/SubstiTUBE