Datasheet - STMicroelectronics

LM158W, LM258W, LM358W
Low-power dual operational amplifier
Datasheet - production data
• Very low supply current per operator essentially independent of supply voltage
• Low input bias current: 20 nA
(temperature compensated)
D and S
SO8 and MiniSO8
(plastic micropackage)
• Low input offset voltage: 2 mV
• Low input offset current: 2 nA
• Input common mode voltage range includes
ground
• Differential input voltage range equal to the
power supply voltage
P
TSSOP8
(thin shrink small outline package)
• Large output voltage swing 0 V to (VCC+) 1.5 V
Pin connections
(top view)
1
Description
The LM158W, LM258W, and LM358W circuits
consist of two independent, high-gain, operational
amplifiers (op amps), which employ internal
frequency compensation and are specifically
designed to operate from a single power supply
over a wide range of voltages. The low-power
supply drain is independent of the power supply
voltage magnitude. Application areas include
transducer amplifiers, DC gain blocks, and all the
conventional op amp circuits, which can now be
more easily implemented in single power supply
systems. For example, these circuits can be
directly supplied with the standard +5 V, which is
used in logic systems and easily provide the
required interface electronics with no additional
power supply. In linear mode, the input common
mode voltage range includes ground. The output
voltage can also swing to ground, even though
operated from a single power supply voltage.
8
2
-
3
+
4
7
-
6
+
5
1 - Output 1
2 - Inverting input
3 - Non-inverting input
4 - VCC5 - Non-inverting input 2
6 - Inverting input 2
7 - Output 2
8 - VCC+
Features
• ESD internal protection: 2 kV
• Internal frequency compensation implemented
• Large DC voltage gain: 100 dB
• Wide bandwidth (unity gain): 1.1 MHz
(temperature compensated)
May 2015
This is information on a product in full production.
DocID9159 Rev 13
1/20
www.st.com
Contents
LM158W, LM258W, LM358W
Contents
1
Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4
Typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1
SO8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2
MiniSO8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.3
TSSOP8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/20
DocID9159 Rev 13
LM158W, LM258W, LM358W
1
Schematic diagram
Schematic diagram
Figure 1. Schematic diagram (1/2 LM158W/LM258W/LM358W)
DocID9159 Rev 13
3/20
20
Absolute maximum ratings and operating conditions
2
LM158W, LM258W, LM358W
Absolute maximum ratings and operating conditions
Table 1. Absolute maximum ratings
Symbol
VCC+
Vin
Vid
Parameter
LM158W/AW LM258W/AW LM358W/AW
Supply voltage
+32
-0.3 to VCC+ +0.3
Input voltage
V
+
Differential input voltage
-0.3 to VCC +0.3
Output short-circuit duration(1)
Iin
Unit
Infinite
5 mA in DC or 50 mA in AC
(duty cycle=10 %, T=1s)
Input current(2)
Toper
Operating free-air temperature range
Tstg
Storage temperature range
-55 to +125
-40 to +105
mA
0 to +70
°C
-65 to +150
Maximum junction temperature
150
Rthja
Thermal resistance junction to ambient(3)
SO8
MiniSO8
TSSOP8
125
190
120
Rthjc
Thermal resistance junction to case(3)
SO8
MiniSO8
TSSOP8
40
39
37
HBM: human body model(4)
2
kV
200
V
1.5
kV
Tj
ESD
MM: machine
model(5)
CDM: charged device model
(6)
°C/W
1. Short-circuits from the output to VCC can cause excessive heating if VCC > 15 V. The maximum output current is
approximately 40 mA independent of the magnitude of VCC. Destructive dissipation can result from simultaneous shortcircuits on all amplifiers.
2. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base
junction of the input PNP transistor becoming forward biased and thereby acting as input diode clamps. In addition to this
diode action, there is also NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the op
amps to go to the VCC voltage level (or to ground for a large overdrive) for the time during which an input is driven negative.
This is not destructive and normal output will be restored for input voltage higher than -0.3 V.
3. Short-circuits can cause excessive heating and destructive dissipation. Rth are typical values.
4. Human body model: a 100 pF capacitor is discharged through a 1.5 kΩ resistor between two pins of the device, done for all
couples of pin combinations with other pins floating.
5. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the
device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins
floating.
6. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to
the ground.
4/20
DocID9159 Rev 13
LM158W, LM258W, LM358W
Absolute maximum ratings and operating conditions
Table 2. Operating conditions
Symbol
VCC+
Parameter
Value
Supply voltage
Unit
3 to 30
(1)
Vicm
Common mode input voltage range
Toper
Operating free air temperature range
LM158W
LM258W
LM358W
V
VDD -0.3 to VCC -1.5
-55 to +125
-40 to +105
0 to +70
°C
1. When used in comparator, the functionality is guaranteed as long as at least one input remains within the
operating common mode voltage range.
DocID9159 Rev 13
5/20
20
Electrical characteristics
3
LM158W, LM258W, LM358W
Electrical characteristics
Table 3. VCC+ = +5 V, VCC- = ground, Vo = 1.4 V, Tamb = +25 °C
(unless otherwise specified)
Symbol
Vio
Parameter
Min.
Input offset voltage(1)
LM158AW
LM258AW, LM358AW
LM158W, LM258W
LM358W
Tmin ≤ Tamb ≤ Tmax
LM158AW, LM258AW, LM358AW
LM158W, LM258W
LM358W
ΔVio/ΔT
Input offset voltage drift
LM158AW, LM258AW, LM358AW
LM158W, LM258W, LM358W
Iio
Input offset current
LM158AW, LM258AW, LM358AW
LM158W, LM258W, LM358W
Tmin ≤ Tamb ≤ Tmax
LM158AW, LM258AW, LM358AW
LM158W, LM258W, LM358W
ΔIio/ΔT
Input offset current drift
LM158AW, LM258AW, LM358AW
LM158W, LM258W, LM358W
Iib
Input bias current(2)
LM158AW, LM258AW, LM358AW
LM158W, LM258W, LM358W
Tmin ≤ Tamb ≤ Tmax
LM158AW, LM258AW, LM358AW
LM158W, LM258W, LM358W
Typ.
Max.
Unit
1
1
2
2
2
3
5
7
mV
4
7
9
7
7
15
30
2
2
10
30
µV/°C
nA
30
40
10
10
200
300
20
20
50
150
pA/°C
nA
100
200
Avd
Large signal voltage gain
VCC+ = +15 V, RL = 2 kΩ, Vo = 1.4 V to 11.4 V
Tmin ≤ Tamb ≤ Tmax
50
25
100
V/mV
SVR
Supply voltage rejection ratio
Rs ≤10 kΩ, VCC+ = 5 V to 30 V
Tmin ≤ Tamb ≤ Tmax
65
65
100
dB
ICC
6/20
Supply current, all amp, no load
Tmin ≤ Tamb ≤ Tmax, VCC+ = +5 V
Tmin ≤ Tamb ≤ Tmax, VCC+ = +30 V
DocID9159 Rev 13
0.7
1.2
2
mA
LM158W, LM258W, LM358W
Electrical characteristics
Table 3. VCC+ = +5 V, VCC- = ground, Vo = 1.4 V, Tamb = +25 °C
(unless otherwise specified) (continued)
Symbol
Parameter
Min.
Typ.
Vicm
Input common mode voltage range
VCC+ = +30 V(3)
Tamb = +25° C
Tmin ≤ Tamb ≤ Tmax
0
0
CMR
Common mode rejection ratio
Rs ≤10 kΩ
Tmin ≤ Tamb ≤ Tmax
70
60
85
Isource
Output current source
VCC+ = +15 V, Vo = +2 V, Vid = +1 V
20
40
Isink
Output sink current
VCC+ = +15 V, Vo = +2 V, Vid = -1 V
VCC+ = +15 V, Vo = +0.2 V, Vid = -1 V
10
12
20
50
26
26
27
27
27
VOH
High level output voltage
RL = 2 kΩ, VCC+ = 30 V
Tmin ≤ Tamb ≤ Tmax
RL = 10 kΩ, VCC+ = 30 V
Tmin ≤ Tamb ≤ Tmax
Max.
VCC+ -1.5
VCC+ -2
Unit
V
dB
60
mA
mA
µA
V
28
VOL
Low level output voltage
RL = 10 kΩ
Tmin ≤ Tamb ≤ Tmax
SR
Slew rate
VCC+ = 15 V, Vi = 0.5 to 3 V, RL = 2 kΩ, CL = 100 pF,
unity gain
0.3
0.6
V/µs
GBP
Gain bandwidth product
VCC+ = 30 V, f =100 kHz, Vin =10 mV, RL=2 kΩ,
CL = 100 pF
0.7
1.1
MHz
THD
Total harmonic distortion
f = 1 kHz, Av = 20 dB, RL = 2 kΩ, Vo = 2 Vpp,
CL = 100 pF, VO = 2 Vpp
0.02
%
Equivalent input noise voltage
f = 1 kHz, Rs = 100 Ω, VCC+ = 30 V
55
nV
-----------Hz
Channel separation (4)
1 kHz ≤ f ≤ 20 kHz
120
dB
en
Vo1/Vo2
+
1. Vo = 1.4 V, Rs = 0 Ω, 5 V < VCC < 30 V, 0 < Vic <
5
VCC+
20
20
mV
- 1.5 V
2. The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output
so there is no change in the load on the input lines.
3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V.
The upper end of the common-mode voltage range is VCC+ - 1.5 V, but either or both inputs can go to +32 V without
damage.
4. Due to the proximity of external components ensure that there is no coupling originating via stray capacitance between
these external parts. Typically, this can be detected at higher frequencies because then this type of capacitance increases.
DocID9159 Rev 13
7/20
20
Electrical characteristics
LM158W, LM258W, LM358W
Figure 3. Large signal frequency response
Figure 4. Voltage follower pulse response
(large signal)
Figure 5. Voltage follower pulse response
(small signal)
Figure 6. Input bias current vs. temperature
Figure 7. Output characteristics (sink)
n
Figure 2. Open loop frequency response
8/20
DocID9159 Rev 13
LM158W, LM258W, LM358W
Electrical characteristics
Figure 8. Output characteristics (source)
Figure 9. Current limiting
Figure 10. Input voltage range
Figure 11. Open loop gain
Figure 12. Supply current
Figure 13. Input bias current vs. positive supply
voltage
DocID9159 Rev 13
9/20
20
Electrical characteristics
LM158W, LM258W, LM358W
Figure 14. Gain bandwidth product
Figure 15. Power supply rejection ratio
Figure 16. Common mode rejection ratio
Figure 17. Phase margin vs. capacitive load
Phase Margin at Vcc=15V and Vicm=7.5V
Vs. Iout and Capacitive load value
10/20
DocID9159 Rev 13
LM158W, LM258W, LM358W
4
Typical applications
Typical applications
Single supply voltage VCC = +5 VDC
Figure 18. AC-coupled inverting amplifier
Rf
100k W
10k W
2VPP
0
eo
RB
6.2kW
R3
100kW
eO
1/2
LM158
Co
1/2
LM158
+5V
RL
10k W
R2
1M W
e
O
R1
10k W
(V)
eI ~
R2
VCC 100k W
A V = 1 + R2
R1
(As shown A V = 101)
Rf
R1
(as shown A V = -10)
R1
10kW
CI
AV= -
Figure 19. Non-inverting DC amplifier
C1
10mF
0
Figure 20. AC-coupled non-inverting amplifier
R1
100kW
Co
1/2
LM158
R3
1M W
100kW
2VPP
0
eo
RB
6.2kW
eI ~
RL
10k W
e2
100k W
e3
100kW
R4
100kW
e4
R5
100kW
Figure 22. High input Z, DC differential amplifier
100kW
5
N
H
/0
5
N
9
9
5
N
/0
eo = e1 + e2 - e3 - e4
where (e1 + e2) ≥ (e3 + e4)
to keep eo ≥ 0V
Figure 23. High input Z adjustable gain DC
instrumentation amplifier
5
N
5
N
5
N
eO
1/2
LM158
100kW
VCC
C2
10mF
100kW
A = 1 + R2
V
R1
(as shown A V = 11)
C1
0.1mF
CI
Figure 21. DC summing amplifier
e1
R2
1MW
e I (mV)
/0
5
N
5
N
H2
/0
*DLQ DGMXVW
5
N
9R
/0
5
N
5
N
H
LI5 5DQG5 5 5 5
@HH
HR > 5
5
,I5 5DQG5 5 5 5
$VVKRZQHR HH
H >55@HH
$VVKRZQH H H DocID9159 Rev 13
11/20
20
Typical applications
LM158W, LM258W, LM358W
Figure 24. Using symmetrical amplifiers to
reduce input current
Figure 25. Low drift peak detector
IB
I
eI
IB
I
IB
1/2
LM158
eo
2N 929
C
eI
0.001mF
IB
IB
1/2
LM158
1mF
ZI
3MW
IB
R
1MW
Input current compensation
0.001mF
IB
2IB
1/2
LM158
3R
3MW
1.5MW
IB
Figure 26. Active band-pass filter
R1
100kW
C1
330pF
R2
100kW
+V1
1/2
LM158
R5
470kW
R4
10MW
1/2
LM158
C2
R3
100kW
330 pF
R6
470kW
Vo
1/2
LM158
R7
100kW
VCC
R8
100kW
12/20
DocID9159 Rev 13
C3
10mF
eo
Zo
2I B
2N 929
IB
1/2
LM158
1/2
LM158
Input current
compensation
LM158W, LM258W, LM358W
5
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
DocID9159 Rev 13
13/20
20
Package information
5.1
LM158W, LM258W, LM358W
SO8 package information
Figure 27. SO8 package outline
Table 4. SO8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.75
0.25
Max.
0.069
A1
0.10
A2
1.25
b
0.28
0.48
0.011
0.019
c
0.17
0.23
0.007
0.010
D
4.80
4.90
5.00
0.189
0.193
0.197
E
5.80
6.00
6.20
0.228
0.236
0.244
E1
3.80
3.90
4.00
0.150
0.154
0.157
e
0.004
0.010
0.049
1.27
0.050
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
L1
k
ccc
14/20
Inches
1.04
1°
0.040
8°
0.10
DocID9159 Rev 13
1°
8°
0.004
LM158W, LM258W, LM358W
5.2
Package information
MiniSO8 package information
Figure 28. MiniSO8 package outline
Table 5. MiniSO8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.1
A1
0
A2
0.75
b
Max.
0.043
0.15
0
0.95
0.030
0.22
0.40
0.009
0.016
c
0.08
0.23
0.003
0.009
D
2.80
3.00
3.20
0.11
0.118
0.126
E
4.65
4.90
5.15
0.183
0.193
0.203
E1
2.80
3.00
3.10
0.11
0.118
0.122
e
L
0.85
0.65
0.40
0.60
0.006
0.033
0.026
0.80
0.016
0.024
L1
0.95
0.037
L2
0.25
0.010
k
ccc
0°
0.037
8°
0.10
DocID9159 Rev 13
0°
0.031
8°
0.004
15/20
20
Package information
5.3
LM158W, LM258W, LM358W
TSSOP8 package information
Figure 29. TSSOP8 package outline
Table 6. TSSOP8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.2
A1
0.05
A2
0.80
b
Max.
0.047
0.15
0.002
1.05
0.031
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.008
D
2.90
3.00
3.10
0.114
0.118
0.122
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.177
e
16/20
Inches
1.00
0.65
k
0°
L
0.45
0.60
0.006
0.039
0.041
0.0256
8°
0°
0.75
0.018
8°
0.024
L1
1
0.039
aaa
0.1
0.004
DocID9159 Rev 13
0.030
LM158W, LM258W, LM358W
6
Ordering information
Ordering information
Table 7. Order codes
Order code
LM158WDT
Temperature range
Package
Packaging
-55 °C, +125 °C
LM258AWDT
158W
SO8
258AW
LM258WDT
258W
LM258WPT
LM258WYDT
LM258WYPT
(1)
-40 °C, +105 °C
(2)
LM258AWYPT
MiniSO8
LM358AWDT
SO8
0 °C, +70 °C
258W
TSSOP8
TSSOP8
(automotive grade)
(2)
LM358WST
LM358AWPT
Marking
TSSOP8
258WY
Tape and reel
258WY
K410
K417
358AW
LM358AWST
MiniSO8
K418
LM358WDT
SO8
358W
1. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC
Q001 & Q 002 or equivalent are qualified.
2. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC
Q001 & Q 002 or equivalent are on-going.
DocID9159 Rev 13
17/20
20
Revision history
7
LM158W, LM258W, LM358W
Revision history
Table 8. Document revision history
Date
Revision
01-Nov-2002
1
First release.
01-Jul-2005
2
ESD protection inserted in Table 1: Absolute maximum ratings on
page 4.
06-Oct-2006
3
ESD tolerance for model HBM improved to 2kV inTable 1: Absolute
maximum ratings on page 4.
Rthja and Rthjc typical values added in Table 1: Absolute maximum
ratings on page 4.
Added Figure 17: Phase margin vs. capacitive load on page 10.
02-Jan-2007
4
Order codes added (automotive grade level) to Section 6: Ordering
information.
15-Mar-2007
5
Previously called revision 4.
Footnote for automotive grade order codes added to Section 6:
Ordering information.
25-Apr-2007
6
Added missing Revision 4 of January 2007 in revision history.
Corrected revision number of March 2007 to Revision 5.
7
Reformatted electrical characteristics table.
Reformatted package information.
Corrected MiniSO8 package information.
Corrected operating temperature range for automotive grade parts.
26-Aug-2008
8
Corrected ESD values in Table 1: Absolute maximum ratings.
Added limitations on input current in Table 1: Absolute maximum
ratings.
Corrected title for Figure 11.
Added E and L1 parameters in Table 4: SO8 package mechanical
data.
Added automotive grade products for MSO8 package in Table 7:
Order codes.
03-Jul-2012
9
Automotive grade level updated in Table 7: Order codes.
Removed order codes: LM358WYD, LM358AWYD, LM258WYD,
LM258AWYD.
10
Small text changes in Features and Description.
Figure 1: Schematic diagram (1/2 LM158W/LM258W/LM358W):
replaced.
Table 7: Order codes: added order codes LM358WST and
LM358AWST.
11-Feb-2008
09-Jan-2013
Changes
Table 3: replaced DVio with ΔVio/ΔT and DIio with ΔIio/ΔT
15-Jul-2013
18/20
11
Table 7: Order codes: removed the following order codes:
LM158WN, LM158WD, LM258AWYST, LM258WAN, LM258WAD,
LM258WD, LM258WYST, LM358WN, LM358WD, LM358AWD,
LM358WDT, LM358AWDT, LM358WPT, LM358AWPT,
LM358WYDT, LM358AWYDT, LM358AWYPT; updated footnote 1.
DocID9159 Rev 13
LM158W, LM258W, LM358W
Revision history
Table 8. Document revision history
Date
Revision
Changes
Removed DIP8 package
18-Sep-2014
12
06-May-2015
13
Table 7: Order codes: removed the order codes LM258WN,
LM258AWYDT, LM258AWPT, LM358AWYST, LM358WYST, and
LM358WYPT; added the order codes LM258WYDT, LM358AWDT,
LM358AWPT, and LM358WDT.
Section 5: Package information: replaced “package mechanical
drawing” with “package outline”.
Table 7: Order codes: removed “tube” packaging from all products
DocID9159 Rev 13
19/20
20
LM158W, LM258W, LM358W
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2015 STMicroelectronics – All rights reserved
20/20
DocID9159 Rev 13