EC/AC axial fans - HyBlade® Ø 300-450 - ebm

EC/AC axial fans - HyBlade®
Ø 300-450
The engineer’s choice
version 03/2012
The new "little ones": axial fans with HyBlade®
technology.
The success of our HyBlade® series continues:
Axial fans with one-of-a-kind HyBlade® technology have been expanded by adding sizes 300 to 450
mm and are now available in all sizes from 300 to 900 mm.
In the process, the one-piece, glass fibre-reinforced plastic impellers have been further optimised in
terms of aerodynamics. Thus, the noise behaviour was improved even more and impeller efficiency
was increased.
For the drive, you can choose between tried and true AC asynchronous motors and high-efficiency
GreenTech EC motors. Furthermore, you can choose between two different control configurations:
one with two fixed speed stages or one with the familiar continuous control option via a combined
0-10V/PWM control input.
Here, the 2-stage designs are laid out so that the small stage corresponds to its AC counterpart in
terms of air performance. The large stage then offers additional increases in air performance beyond
that. This opens entirely new prospects, such as in refrigeration system applications.
Since the electronics have been completely integrated into the motor, our axial fans using GreenTech
EC technology have precisely the same mounting dimension as their AC counterparts and thus are
able to replace them without cost-intensive renovations.
The advantages at a glance
- High efficiency due to HyBlade® axial impellers and new GreenTech EC motors
- Reduced noise
- Compact design
- Mechanical compatibility of AC and EC
- GreenTech EC fans alternatively controlled with two speeds or continuous
- Compliance with ErP specifications* (please note individual designation)
*ErP: Energy related Product – defined minimum requirements for fans in accordance with the
EcoDesign directive for fans with a drive output of 125 W or higher.
2
Table of contents
The new "little ones": axial fans
with HyBlade® technology
2
GreenTech: The Green Company
4
EC axial fans - HyBlade® Ø 300-450
6
AC axial fans - HyBlade® Ø 300-450
34
Accessories
54
Electrical connections EC/AC
56
Technical parameters & scope
62
ebm-papst representatives & subsidiaries
66
3
Sustainability is at the centre of our
thoughts and actions. Out of conviction!
Eco-friendliness and sustainability have always been at the core of our thoughts and actions. For decades, we have worked
according to the simple but strict creed of our co-founder Gerhard Sturm: “Each new product we develop has to be better
than the last one in terms of economy and ecology.” GreenTech is the ultimate expression of our corporate philosophy.
GreenTech is pro-active development.
GreenTech is acknowledged and certified.
Even in the design phase, the materials and processes we use are optimi-
Every step in our chain of production meets the stringent standards of
sed for the greatest possible eco-friendliness, energy balance and –
environmental specialists and the public. The 2008 Environmental Prize
wherever possible – recyclability. We continually improve the material
of Baden-Wuerttemberg, the Green Award 2009, the Energy Efficiency
and performance of our products, as well as the flow and noise charac-
Award 2009 of the dena – to give just a few examples – testify to this.
teristics. At the same time, we significantly reduce energy consumption.
The environmental advantage gained in the performance of the products
Close co-operation with universities and scientific institutes and the pro-
developed from our GreenTech philosophy can also be measured in the
fessorship we endow in the area of power engineering and regenerative
fulfilment of the most stringent energy and environmental standards.
energies allows us to profit from the latest research findings in these
In many instances, our products are already well below the thresholds
fields – and at the same time ensure highly qualified young academics.
energy legislation will impose a few years from now – several times over.
GreenTech is eco-friendly production.
Our customers profit from this every day.
GreenTech also stands for maximum energy efficiency in our production
The heart of GreenTech is future-oriented EC technology from ebm-
processes. There, the intelligent use of industrial waste heat and ground-
papst. The EC technology at the core of our most efficient motors and
water cooling, photovoltaics and, of course, our own cooling and venti -
fans allows efficiency of up to 90%, saves energy at a very high level,
lation technology are of the utmost importance. Our most modern plant,
significantly extends service life and makes our products maintenance-
for instance, consumes 91% less energy than currently specified and
free. These values pay off not only for the environment, but every cent al-
required. In this way, our products contribute to protecting the environ-
so pays off for the user! All ebm-papst products – even those for which
ment, from their origin to their recyclable packaging.
GreenTech EC technology does not (yet) make sense from an application
viewpoint – feature the greatest possible connection of economy and
ecology.
5
6
EC axial fans - HyBlade® Ø 300-450
EC axial fans HyBlade® Ø 300-450
8
7
EC axial fans - HyBlade®
Ø 300
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass without
attachments
Hz
rpm
W
A
Pa
°C
kg
Motor
*3G 300
M3G 055-CF
A
1~ 200-240
50/60
*3G 300
M3G 055-DF
B
1~ 200-240
*3G 300
M3G 074-CF
C
1~ 200-240
*3G 300
M3G 055-CF
D
*3G 300
M3G 055-DF
E
*3G 300
M3G 074-CF
F
subject to alterations
1500
85
0,74
85
-25..+60
1,30
2 Speed stages
p. 56 / H3)
50/60
1750
120
1,00
100
-25..+40
1,50
2 Speed stages
p. 56 / H3)
50/60
2050
168
1,35
135
-25..+60
1,98
2 Speed stages
p. 56 / H3)
1~ 200-240
50/60
1500
85
0,74
85
-25..+60
1,35
Speed-controlled
p. 57 / H4)
1~ 200-240
50/60
1660
98
0,80
80
-25..+60
1,55
Speed-controlled
p. 57 / H4)
1~ 200-240
50/60
2050
168
1,35
135
-25..+60
1,98
Speed-controlled
p. 57 / H4)
(1) Nominal data in operating point with maximum load and 230 VAC
Air performance measured
in H2O
Pa
Curves (2 Speed stages)
140
1650
72
0,63
63
1600
78
0,67
63
A
3
1565
83
0,70
62
and without protection against
A
4
1500
85
0,74
64
accidental contact
A
5
1485
52
0,48
60
A
6
1440
56
0,51
60
A
7
1410
59
0,53
60
LpA measured at 1 m distance
A
8
1365
65
0,59
62
to fan axis
B
1
1820
96
0,86
67
B
2
1775
105
0,94
67
only valid under the measur-
B
3
1750
111
0,98
67
ment conditions listed and
B
4
1750
120
1,00
69
may vary depending on the
B
5
1430
45
0,44
63
B
6
1415
51
0,51
61
With any deviation to the stan-
B
7
1395
56
0,54
60
dard setup, the specific values
B
8
1370
60
0,57
61
C
1
2390
168
1,30
71
C
2
2250
167
1,35
71
For detailed information
C
3
2145
168
1,35
69
see page 62 ff.
C
4
2050
168
1,35
72
C
5
1910
88
0,75
66
C
6
1865
97
0,81
66
C
7
1830
105
0,86
65
C
8
1790
112
0,91
66
0,5
0,4
Suction-side noise levels:
8
4
C
LWA as per ISO 13347,
90
3
4
0,3
80
A
The acoustic values given are
8
70
3
8
B
7
60
0,2
50
3
7
installation situation.
7
2
40
6
30
2
0,1
2
have to be checked and re-
6
6
20
viewed once installed or fitted!
10
psf
5
0
qV
8
200
400
500
600
1000
800
1500
1000
1200
2000
1
1
5 1
1400
2500
1600
1800
3000
cfm
m3/h
LWA
dB(A)
2
110
B
I
A
1
in ebm-papst full nozzle
120
Pe
W
A
Installation category A,
4
n
rpm
A
as per: ISO 5801,
130
100
Technical features
and electr. connection
Speed/rpm(1)
VAC
Type
2-stages / 0-10 V
Frequency
Nominal data
Nominal
voltage range
Curve
– Material: Guard grille: Steel, phosphated and coated in black plastic (RAL9005)
Wall ring: Sheet steel, pre-galvanised and coated in black plastic (RAL9005)
Blades: Plastic PP
Rotor: Surface passivated
Electronics enclosure: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharge holes: None, open rotor
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Direction of air flow
– Technical features: See electrical connections p. 60 ff.
– EMC: Inerference immunity acc. to EN 61000-6-2 (industrial environment)
Harmonics acc. to EN 61000-3-2/3
Interference emission acc. to EN 61000-6-3 (household environment)
On account of the installation conditions, ferritic damping in the
connection line may be required for the application.
– Leakage current: < 3,5 mA acc. to EN 60335-1
– Cable exit: Variable
– Terminal box design: Electrical connection via terminal strip
– Protection class: I
– Product conforming to standards: EN 60335-1; CE
– Approvals: VDE, CURUS on request
❮ "V"
❮ "V"
Without
attachments
❮ "V"
With full
round nozzle
❮ "V"
With guard grille
for short nozzle
With guard grille for short nozzle
and mounted terminal box
"V"
A3G 300-AK13 -01
W3G 300-CK13 -30
S3G 300-AK13 -30
S3G 300-AK13 -50*
"V"
A3G 300-AL11 -01
W3G 300-CL11 -30
S3G 300-AL11 -30
S3G 300-AL11 -50*
"V"
A3G 300-AN02 -01
W3G 300-CN02 -30
S3G 300-AN02 -30
S3G 300-AN02 -50*
"V"
A3G 300-AK13 -03
W3G 300-CK13 -32
S3G 300-AK13 -32
S3G 300-AK13 -52*
"V"
A3G 300-AL11 -03
W3G 300-CL11 -32
S3G 300-AL11 -32
S3G 300-AL11 -52*
"V"
A3G 300-AN02 -03
W3G 300-CN02 -32
S3G 300-AN02 -32
S3G 300-AN02 -52*
*Terminal box design: Electrical connection via terminal strip
Direction of air flow "A" on request
140
Air performance measured
in H2O
Pa
Curves (Speed-controlled)
as per: ISO 5801,
F
0,5
in ebm-papst full nozzle
and without protection against
120
accidental contact
0,4
90
3
0,3
D
E
72
0,63
63
1600
78
0,67
63
D
3
1565
83
0,70
62
D
4
1500
85
0,74
64
1
1740
81
0,67
66
2
1710
88
0,74
66
LWA as per ISO 13347,
E
3
1690
93
0,77
66
LpA measured at 1 m distance
E
4
1660
98
0,80
66
F
1
2390
168
1,30
71
F
2
2250
167
1,35
71
F
3
2145
168
1,35
69
F
4
2050
168
1,35
72
only valid under the measurment conditions listed and
3
may vary depending on the
0,2
50
1650
2
E
The acoustic values given are
60
1
D
E
4
70
LWA
dB(A)
to fan axis
4
80
I
A
Suction-side noise levels:
110
100
Pe
W
D
Installation category A,
4
130
n
rpm
installation situation.
3
2
40
With any deviation to the stan-
30
dard setup, the specific values
0,1
2
have to be checked and re-
2
viewed once installed or fitted!
20
10
For detailed information
psf
1
0
qV
200
400
500
600
1000
800
1500
1000
1200
2000
1400
2500
see page 62 ff.
1
1
1600
1800
3000
cfm
m3/h
9
Drawings
p. 10 ff.
Electr. connections
p. 56/57
EC axial fans - HyBlade®
Ø 300 with motor M3G 055, 2 Speed stages, drawings for direction of air flow "V"
Without attachments
74±3
59±2
Mass
kg
A3G 300-AK13 -01
1,30
Depth of screw
max. 5 mm
Ø89
Ø80
Ø27
Ø300±2
M4(4x)
Type
450
85±1 +20
0
6
Internal diameter of the
wall ring at least 306 mm
2
78.4±1
Ø58±0,2
brass lead tips
crimped
❮ "V"
With full round nozzle
84
80
0˚
6x6
Type
Mass
kg
W3G 300-CK13 -30
3,30
Type
Mass
kg
15˚
Ø397
Ø326
Ø9
80
Ø3
11
❮ "V"
With guard grille for short nozzle
S3G 300-AK13 -30 2,30
S3G 300-AK13 -50* 2,45
❮ "V"
10
28.4±2
Ø360
Tightening torque: 0,8 Nm±0,15 Nm
94
Ø4.3
.5
4.5
57.2
*Type with terminal
box:
91
Ø329.6
23.9±3
58.5
Internal diameter of the
wall ring at least 306 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
EC axial fans - HyBlade®
Ø 300 with motor M3G 055, Speed-controlled, drawings for direction of air flow "V"
Without attachments
74±3
59±2
M4(4x)
Type
Mass
kg
A3G 300-AK13 -03
1,35
Ø89
Ø80
Ø27
Ø300±2
Depth of screw
max. 5 mm
45
0+
20
Internal diameter of the
wall ring at least 306 mm
78.4±1
❮ "V"
brass lead tips
crimped
85 6
±1
0
2
Ø58±0,2
With full round nozzle
84
80
Type
Mass
kg
W3G 300-CK13 -32
3,35
Type
Mass
kg
6x6
15˚
0˚
Ø397
Ø326
Ø9
80
Ø3
11
❮ "V"
With guard grille for short nozzle
S3G 300-AK13 -32 2,35
S3G 300-AK13 -52* 2,50
Ø360
.5
❮ "V"
28.4±2
Tightening torque: 0,8 Nm±0,15 Nm
94
Ø4.3
4.5
57.2
*Type with terminal
box:
91
Ø330.4
23.9±3
68.5
Internal diameter of the
wall ring at least 306 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
11
EC axial fans - HyBlade®
Ø 300 with motor M3G 055, 2 Speed stages, drawings for direction of air flow "V"
Without attachments
Depth of screw
max. 10 mm
79.5±3
59±2
M6(4x)
M4(4x)
Type
Mass
kg
A3G 300-AL11 -01
1,50
Depth of screw
max. 5 mm
Ø101
Ø75
Ø300±2
Ø58±0.2
Ø90±0.2
Internal diameter of the
wall ring at least 306 mm
4
85±1 50+20
0
6
5
100.7±1
brass lead tips
crimped
❮ "V"
With full round nozzle
85
80
0˚
6x6
Type
Mass
kg
W3G 300-CL11 -30
3,55
Type
Mass
kg
15˚
Ø397
Ø326
Ø9
80
Ø3
11
❮ "V"
With guard grille for short nozzle
S3G 300-AL11 -30 2,50
S3G 300-AL11 -50* 2,65
57.2
4.5
50.6±2
❮ "V"
12
Tightening torque: 0,8 Nm±0,15 Nm
91
.
5
Ø360
*Type with terminal
box:
94
Ø330
34.3±3
68.5
Ø4.3
Internal diameter of the
wall ring at least 306 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
EC axial fans - HyBlade®
Ø 300 with motor M3G 055, Speed-controlled, drawings for direction of air flow "V"
Without attachments
Depth of screw
max. 10 mm
79.5±3
59±2
M6(4x)
M4(4x)
Type
Mass
kg
A3G 300-AL11 -03
1,55
Depth of screw
max. 5 mm
Ø101
Ø75
Ø300±2
Ø58±0.2
Ø90±0.2
Internal diameter of the
wall ring at least 306 mm
450
85±1 +20
0
6
5
100.7±1
❮ "V"
brass lead tips
crimped
With full round nozzle
85
80
0˚
6x6
Type
Mass
kg
W3G 300-CL11 -32
3,60
Type
Mass
kg
15˚
Ø397
Ø326
Ø9
80
Ø3
11
❮ "V"
With guard grille for short nozzle
S3G 300-AL11 -32 2,55
S3G 300-AL11 -52* 2,70
57.2
4.5
50.6±2
❮ "V"
Tightening torque: 0,8 Nm±0,15 Nm
91
.
5
Ø360
*Type with terminal
box:
94
Ø330
34.3±3
68.5
Ø4.3
Internal diameter of the
wall ring at least 306 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
13
EC axial fans - HyBlade®
Ø 300 with motor M3G 074, 2 Speed stages, drawings for direction of air flow "V"
Without attachments
Depth of screw
max. 10 mm
86.5±3
57.5±2
M6(4x)
M4(4x)
Type
Mass
kg
A3G 300-AN02 -01
1,98
Depth of screw
max. 5 mm
Ø101
Ø75
Ø300±2
Ø58±0.2
5
Internal diameter of the
wall ring at least 306 mm
20
0+
60 5±10
8 6
96±1
Ø90±0.2
brass lead tips
crimped
❮ "V"
With full round nozzle
98.2±2
86.5±3
80
6x6
15˚
Type
Mass
kg
W3G 300-CN02 -30
4,00
Type
Mass
kg
0˚
Ø397
Ø326
Ø9
80
Ø3
11
❮ "V"
With guard grille for short nozzle
S3G 300-AN02 -30 2,93
S3G 300-AN02 -50* 3,08
55
5
❮ "V"
14
40.8±2
Tightening torque: 0,8 Nm±0,15 Nm
91
.
5
Ø360
*Type with terminal
box:
Ø6.5+0.3
94
Ø324.5
36.5 ±3
71
Internal diameter of the
wall ring at least 306 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
EC axial fans - HyBlade®
Ø 300 with motor M3G 074, Speed-controlled, drawings for direction of air flow "V"
Without attachments
Depth of screw
max. 10 mm
86.5±3
57.5±2
M6(4x)
M4(4x)
Type
Mass
kg
A3G 300-AN02 -03
1,98
Depth of screw
max. 5 mm
Ø101
Ø75
Ø300±2
Ø58±0.2
Internal diameter of the
wall ring at least 306 mm
5
20
0+
60 5±10
8 6
96±1
Ø90±0.2
brass lead tips
crimped
❮ "V"
With full round nozzle
98.2±2
86.5±3
80
Type
Mass
kg
W3G 300-CN02 -32
4,00
Type
Mass
kg
6x6
15˚
0˚
Ø397
Ø326
Ø9
80
Ø3
11
❮ "V"
With guard grille for short nozzle
S3G 300-AN02 -32 2,93
S3G 300-AN02 -52* 3,08
5
55
40.8±2
❮ "V"
Tightening torque: 0,8 Nm±0,15 Nm
91
.
5
Ø360
*Type with terminal
box:
Ø6.5+0.3
94
Ø324.5
36.5 ±3
71
Internal diameter of the
wall ring at least 306 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
15
EC axial fans - HyBlade®
Ø 350
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass without
attachments
Hz
rpm
W
A
Pa
°C
kg
Motor
*3G 350
M3G 055-DF
A
1~ 200-240
50/60
*3G 350
M3G 074-CF
B
1~ 200-240
*3G 350
M3G 055-DF
C
1~ 200-240
*3G 350
M3G 074-CF
D
1~ 200-240
subject to alterations
1115
85
0,73
60
50/60
1480
165
1,35
50/60
1115
85
0,73
50/60
1480
165
1,35
in H2O
Pa
p. 57 / H4)
2,20
Speed-controlled
p. 57 / H4)
100
-25..+60
Air performance measured
0,4
4
B
1215
74
0,63
65
1190
80
0,67
63
A
3
1160
84
0,70
60
and without protection against
A
4
1115
85
0,73
58
accidental contact
A
5
915
34
0,33
57
A
6
895
36
0,34
55
A
7
880
39
0,37
54
A
8
860
41
0,40
52
B
1
1575
141
1,15
71
The acoustic values given are
B
2
1555
152
1,23
69
only valid under the measur-
B
3
1530
161
1,31
66
ment conditions listed and
B
4
1480
165
1,35
67
B
5
1395
98
0,82
68
B
6
1375
106
0,88
66
With any deviation to the stan-
B
7
1355
114
0,96
64
dard setup, the specific values
B
8
1340
122
1,03
64
0,3
to fan axis
3
60
0,2
7
may vary depending on the
A
40
installation situation.
3
8
2
30
0,1
6
7
20
have to be checked and re-
2
viewed once installed or fitted!
6
10
For detailed information
1
5
200
400
500
600
1000
800
1000
1500
1200
2000
1400
2500
1600
1800
3000
see page 62 ff.
1
5
2000
3500
2200 cfm
m3/h
LWA
dB(A)
2
LpA measured at 1 m distance
4
I
A
1
LWA as per ISO 13347,
70
Pe
W
A
Suction-side noise levels:
8
n
rpm
A
as per: ISO 5801,
80
psf
p. 56 / H3)
Speed-controlled
-25..+60
90
16
2 Speed stages
1,63
-25..+60
60
Installation category A,
qV
2,20
100
in ebm-papst full nozzle
0
p. 56 / H3)
1,63
(1) Nominal data in operating point with maximum load and 230 VAC
110
50
2 Speed stages
-25..+60
Curves (2 Speed stages)
100
Technical features
and electr. connection
Speed/rpm(1)
VAC
Type
2-stages / 0-10 V
Frequency
Nominal data
Nominal
voltage range
Curve
– Material: Guard grille: Steel, phosphated and coated in black plastic (RAL9005)
Wall ring: Sheet steel, pre-galvanised and coated in black plastic (RAL9005)
Blades: Plastic PP
Rotor: Surface passivated
Electronics enclosure: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharge holes: None, open rotor
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Direction of air flow
– Technical features: See electrical connections p. 60 ff.
– EMC: Inerference immunity acc. to EN 61000-6-2 (industrial environment)
Harmonics acc. to EN 61000-3-2/3
Interference emission acc. to EN 61000-6-3 (household environment)
On account of the installation conditions, ferritic damping in the
connection line may be required for the application.
– Leakage current: < 3,5 mA acc. to EN 60335-1
– Cable exit: Variable
– Terminal box design: Electrical connection via terminal strip
– Protection class: I
– Product conforming to standards: EN 60335-1; CE
– Approvals: VDE, CURUS on request
❮ "V"
❮ "V"
Without
attachments
❮ "V"
With full
round nozzle
❮ "V"
With guard grille
for short nozzle
With guard grille for short nozzle
and mounted terminal box
"V"
A3G 350-AG03 -01
W3G 350-CG03 -30
S3G 350-AG03 -30
S3G 350-AG03 -50*
"V"
A3G 350-AN01 -01
W3G 350-CN01 -30
S3G 350-AN01 -30
S3G 350-AN01 -50*
"V"
A3G 350-AG03 -03
W3G 350-CG03 -32
S3G 350-AG03 -32
S3G 350-AG03 -52*
"V"
A3G 350-AN01 -03
W3G 350-CN01 -32
S3G 350-AN01 -32
S3G 350-AN01 -52*
*Terminal box design: Electrical connection via terminal strip
Direction of air flow "A" on request
Air performance measured
in H2O
Pa
Curves (Speed-controlled)
as per: ISO 5801,
110
0,4
100
D
4
and without protection against
accidental contact
0,3
70
I
A
LWA
dB(A)
1
1215
74
0,63
65
C
2
1190
80
0,67
63
C
3
1160
84
0,70
60
C
4
1115
85
0,73
58
D
1
1575
141
1,15
71
Suction-side noise levels:
D
2
1555
152
1,23
69
LWA as per ISO 13347,
D
3
1530
161
1,31
66
LpA measured at 1 m distance
D
4
1480
165
1,35
67
90
80
Pe
W
C
Installation category A,
in ebm-papst full nozzle
n
rpm
to fan axis
3
60
4
The acoustic values given are
C
only valid under the measurment conditions listed and
0,2
50
may vary depending on the
40
installation situation.
3
2
30
With any deviation to the stan-
0,1
dard setup, the specific values
20
have to be checked and re-
2
viewed once installed or fitted!
10
For detailed information
psf
0
qV
200
400
500
600
1000
800
1500
1000
1200
2000
1400
2500
1600
see page 62 ff.
1
1
1800
3000
2000
3500
2200 cfm
m3/h
17
Drawings
p. 18 ff.
Electr. connections
p. 56/57
EC axial fans - HyBlade®
Ø 350 with motor M3G 055, 2 Speed stages, drawings for direction of air flow "V"
Without attachments
97.3±3
87±2
Mass
kg
A3G 350-AG03 -01
1,63
Depth of screw
max. 5 mm
Ø89
Ø80
Ø27
Ø352±2
M4(4x)
Type
6
85 450
±1 +2
0 0
Internal diameter of the
wall ring at least 358 mm
2
Ø58±0.2
88.4±1
brass lead tips
crimped
❮ "V"
With full round nozzle
35
97.3±3
80
0˚
6x6
Type
Mass
kg
W3G 350-CG03 -30
4,55
Type
Mass
kg
15˚
Ø460
Ø390
Ø390
Ø9
42
Ø4
12
❮ "V"
With guard grille for short nozzle
S3G 350-AG03 -30 3,15
S3G 350-AG03 -50* 3,30
Tightening torque: 0,8 Nm±0,15 Nm
94
.5
Ø422
*Type with terminal
box:
91
Ø375
25.3±3
58.5
4.5
79.3
❮ "V"
18
Ø6.5
16.4±2
Internal diameter of the
wall ring at least 358 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
EC axial fans - HyBlade®
Ø 350 with motor M3G 055, Speed-controlled, drawings for direction of air flow "V"
Without attachments
97.3±3
87,3±2
M4(4x)
Type
Mass
kg
A3G 350-AG03 -03
1,63
Ø89
Ø80
Ø27
Ø352±2
Depth of screw
max. 5 mm
6
2
85
±1
0
45
0+
20
Internal diameter of the
wall ring at least 358 mm
Ø58±0.2
88.4±1
❮ "V"
brass lead tips
crimped
With full round nozzle
35
97.3±3
80
6x6
15˚
Type
Mass
kg
W3G 350-CG03 -32
4,55
Type
Mass
kg
0˚
Ø390
Ø460
Ø390
Ø9
42
Ø4
12
❮ "V"
With guard grille for short nozzle
S3G 350-AG03 -32 3,15
S3G 350-AG03 -52* 3,30
❮ "V"
16.4±2
Ø422
Tightening torque: 0,8 Nm±0,15 Nm
94
.5
4.5
79.3
*Type with terminal
box:
91
Ø375
25.3±3
68.5
Ø6.5
Internal diameter of the
wall ring at least 358 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
19
EC axial fans - HyBlade®
Ø 350 with motor M3G 074, 2 Speed stages, drawings for direction of air flow "V"
Without attachments
Depth of screw
max. 10 mm
97±3
87.3±2
M6(4x)
M4(4x)
Type
Mass
kg
A3G 350-AN01 -01
2,20
Depth of screw
max. 5 mm
Ø101
Ø75
Ø352±2
Ø58±0.2
Ø90±0.2
5
Internal diameter of the
wall ring at least 358 mm
20
0+
60 5±10
8 6
96±1
brass lead tips
crimped
❮ "V"
With full round nozzle
97±3
80
35
6x6
Type
Mass
kg
W3G 350-CN01 -30
5,10
Type
Mass
kg
0˚
15˚
Ø460
Ø403
Ø390
Ø9
42
Ø4
12
❮ "V"
With guard grille for short nozzle
S3G 350-AN01 -30 3,70
S3G 350-AN01 -50* 3,85
5
85
40.8±2
❮ "V"
20
Tightening torque: 0,8 Nm±0,15 Nm
91
.5
Ø422
*Type with terminal
box:
Ø6.5+0.3
94
Ø376
47.3 ±3
41
Internal diameter of the
wall ring at least 358 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
EC axial fans - HyBlade®
Ø 350 with motor M3G 074, Speed-controlled, drawings for direction of air flow "V"
Without attachments
Depth of screw
max. 10 mm
97±3
87.3±2
M6(4x)
M4(4x)
Type
Mass
kg
A3G 350-AN01 -03
2,20
Depth of screw
max. 5 mm
Ø101
Ø75
Ø352±2
Ø58±0.2
Ø90±0.2
5
Internal diameter of the
wall ring at least 358 mm
20
0+
60 5±10
8 6
96±1
brass lead tips
crimped
❮ "V"
With full round nozzle
97±3
80
35
6x6
Type
Mass
kg
W3G 350-CN01 -32
5,10
Type
Mass
kg
0˚
15˚
Ø390
Ø460
Ø403
Ø9
42
Ø4
12
❮ "V"
With guard grille for short nozzle
S3G 350-AN01 -32 3,70
S3G 350-AN01 -52* 3,85
5
85
40.8±2
❮ "V"
Tightening torque: 0,8 Nm±0,15 Nm
91
.5
Ø422
*Type with terminal
box:
Ø6.5+0.3
94
Ø376
47.3 ±3
41
Internal diameter of the
wall ring at least 358 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
21
EC axial fans - HyBlade®
Ø 400
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass without
attachments
Hz
rpm
W
A
Pa
°C
kg
Motor
*3G 400
M3G 074-CF
A
1~ 200-240
50/60
*3G 400
M3G 074-CF
B
1~ 200-240
*3G 400
M3G 084-FA
C
1~ 200-277
subject to alterations
75
-25..+60
2,3
2 Speed stages
p. 56 / H3)
1,15
75
-25..+60
2,3
Speed-controlled
p. 57 / H4)
2,60
160
-25..+60
4,7
Speed-controlled
p. 58 / K1)
1080
140
1,15
50/60
1080
140
50/60
1630
400
(1) Nominal data in operating point with maximum load and 230 VAC
Air performance measured
in H2O
Pa
Curves (2 Speed stages)
1135
116
0,97
69
1115
126
1,05
67
A
3
1100
131
1,07
64
and without protection against
A
4
1080
140
1,15
67
accidental contact
A
5
930
64
0,60
65
A
6
915
69
0,61
63
A
7
905
73
0,64
59
A
8
890
78
0,69
63
0,25
LWA as per ISO 13347,
0,20
3
LpA measured at 1 m distance
to fan axis
The acoustic values given are
0,15
40
only valid under the measur7
ment conditions listed and
may vary depending on the
30
0,10
installation situation.
2
With any deviation to the stan-
20
dard setup, the specific values
6
have to be checked and re-
0,05
10
viewed once installed or fitted!
For detailed information
psf
0
qV
22
200
500
400
600
1000
800
1000
1500
1200
2000
1400
1600
2500
1800
3000
see page 62 ff.
1
5
2000
3500
2200
2400
4000
cfm
m3/h
LWA
dB(A)
2
Suction-side noise levels:
A
I
A
1
in ebm-papst full nozzle
8
Pe
W
A
Installation category A,
50
n
rpm
A
as per: ISO 5801,
4
70
60
Technical features
and electr. connection
Speed/rpm(1)
VAC
Type
2-stages / 0-10 V
Frequency
Nominal data
Nominal
voltage range
Curve
– Material: Guard grille: Steel, phosphated and coated in black plastic (RAL9005)
Wall ring: Sheet steel, pre-galvanised and coated in black plastic (RAL9005)
Blades: Plastic PP
Rotor: A B Surface passivated; C Surface coated in black
Electronics enclosure: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: A B IP 54; C IP 54 (acc. to EN 60529)
– Insulation class: "B"
– Mounting position: A B Any; C Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharge holes: A B None, open rotor; C Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Direction of air flow
– Technical features: See electrical connections p. 60 ff.
– EMC: Inerference immunity acc. to EN 61000-6-2 (industrial environment)
Harmonics acc. to EN 61000-3-2/3
Interference emission acc. to EN 61000-6-3 (household environment)
On account of the installation conditions, ferritic damping in the
connection line may be required for the application.
– Leakage current: < 3,5 mA A B acc. to EN 60335-1; C acc. to EN 61800-5-1
– Cable exit: Variable
– Terminal box design: Electrical connection via terminal strip
– Protection class: I; C acc. to EN 61800-5-1
– Product conforming to standards: A B EN 60335-1; C EN 61800-5-1; CE
– Approvals: A B VDE, CURUS on request; C CSA; UL
❮ "V"
❮ "V"
Without
attachments
❮ "V"
With full
round nozzle
❮ "V"
With guard grille
for short nozzle
With guard grille for short nozzle
and mounted terminal box
"V"
A3G 400-AN04 -01
W3G 400-CN04 -30
S3G 400-AN04 -30
S3G 400-AN04 -50*
"V"
A3G 400-AN04 -03
W3G 400-CN04 -32
S3G 400-AN04 -32
S3G 400-AN04 -52*
"V"
A3G 400-AC22 -51
W3G 400-CC22 -51
S3G 400-LC22 -51
S3G 400-LC22 -59*
*Terminal box design: Electrical connection via terminal strip
Direction of air flow "A" on request
Air performance measured
in H2O
Pa
Curves (Speed-controlled)
as per: ISO 5801,
0,7
in ebm-papst full nozzle
and without protection against
160
4
C
accidental contact
I
A
LWA
dB(A)
1
1135
116
0,97
69
B
2
1115
126
1,05
67
B
3
1100
131
1,07
64
B
4
1080
140
1,15
67
C
1
1660
350
2,24
78
Suction-side noise levels:
C
2
1645
380
2,43
76
LWA as per ISO 13347,
C
3
1635
391
2,50
72
LpA measured at 1 m distance
C
4
1630
400
2,60
74
0,6
100
3
to fan axis
0,4
120
0,5
140
Pe
W
B
Installation category A,
180
n
rpm
The acoustic values given are
only valid under the measur-
80
ment conditions listed and
0,3
B
may vary depending on the
4
installation situation.
60
0,2
2
With any deviation to the stan-
3
dard setup, the specific values
40
viewed once installed or fitted!
2
0,1
20
have to be checked and re-
For detailed information
psf
0
qV
500
1000
1000
2000
1500
2000
3000
see page 62 ff.
1
1
2500
4000
3000
5000
cfm
m3/h
23
Drawings
p. 24 ff.
Electr. connections
p. 56/57/58
EC axial fans - HyBlade®
Ø 400 with motor M3G 074, 2 Speed stages, drawings for direction of air flow "V"
Type
Without attachments
Depth of screw
max. 10 mm
88.6±2
83.7±3
Mass
kg
A3G 400-AN04 -01
M6(4x)
M4(4x)
2,3
Depth of screw
max. 5 mm
Ø101
Ø75
Ø392±2
Ø58±0.2
Ø90±0.2
20
Internal diameter of the
wall ring at least 400 mm
0+
60 5±10
8 6
5
96±1
brass lead tips
crimped
❮ "V"
Type
With full round nozzle
35
W3G 400-CN04 -30
6x6
6,1
0˚
15˚
96
Mass
kg
Ø419
Ø528
Ø468
Ø9
04
Ø5
12
❮ "V"
Type
With guard grille for short nozzle
S3G 400-AN04 -30 4,10
S3G 400-AN04 -50* 4,25
5
40.8±2
❮ "V"
24
Tightening torque: 0,8 Nm±0,15 Nm
91
.5
Ø470
*Type with terminal
box:
Ø9+0.3
94
Ø415
36.6 ±3
85
Mass
kg
41
Internal diameter of the
wall ring at least 400 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
EC axial fans - HyBlade®
Ø 400 with motor M3G 074, Speed-controlled, drawings for direction of air flow "V"
Type
Without attachments
Depth of screw
max. 10 mm
88.6±2
83.7±3
Mass
kg
A3G 400-AN04 -03
M6(4x)
M4(4x)
2,3
Depth of screw
max. 5 mm
Ø101
Ø75
Ø392±2
Ø58±0.2
Ø90±0.2
20
Internal diameter of the
wall ring at least 400 mm
0+
60 5±10
8 6
5
96±1
brass lead tips
crimped
❮ "V"
Type
With full round nozzle
35
W3G 400-CN04 -32
6x6
6,1
0˚
15˚
96
Mass
kg
Ø419
Ø528
Ø468
Ø9
04
Ø5
12
❮ "V"
Type
With guard grille for short nozzle
S3G 400-AN04 -32 4,10
S3G 400-AN04 -52* 4,25
5
40.8±2
❮ "V"
Tightening torque: 0,8 Nm±0,15 Nm
91
.5
Ø470
*Type with terminal
box:
Ø9+0.3
94
Ø415
36.6 ±3
85
Mass
kg
41
Internal diameter of the
wall ring at least 400 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
25
EC axial fans - HyBlade®
Ø 400 with motor M3G 084, Speed-controlled, drawings for direction of air flow "V"
Type
Without attachments
Mass
kg
A3G 400-AC22 -51
M6(4x)
45˚
Depth of screw
8-10 mm
4x90˚
Ø392±2
Ø178
Ø150±0.25
Ø100
99.6±3
88.6±2
4,7
8
600±20
85±10
Internal diameter of the
wall ring at least 400 mm
47.7
Ø164±0.35
148±2
Core-end sleeve
crimped
❮ "V"
Type
With full round nozzle
Mass
kg
W3G 400-CC22 -51
152.2±3
96
6x6
Ø9
0˚
Ø419
Ø528
Ø468
8,5
04
Ø5
12
❮ "V"
Type
With guard grille for short nozzle
S3G 400-LC22 -51 6,40
S3G 400-LC22 -59* 6,55
❮ "V"
26
10
0
Ø470
Tightening torque: 1,5 Nm±0,2 Nm
0
5
*Type with terminal
box:
10
Ø415
49±3
98
Mass
kg
66.2
Ø9
Internal diameter of the
wall ring at least 400 mm
Cable diameter: min. 4 mm, max. 10 mm
Tightening torque: 2,5 Nm±0,4 Nm
27
EC axial fans - HyBlade®
Ø 450
C
subject to alterations
2 Speed stages
p. 56 / H3)
1,40
70
-25..+60
2,7
Speed-controlled
p. 57 / H4)
2,20
125
-25..+60
4,8
Speed-controlled
p. 58 / K1)
Hz
rpm
W
A
1~ 200-240
50/60
980
170
1,40
1~ 200-240
50/60
980
170
1~ 200-277
50/60
1300
345
(1) Nominal data in operating point with maximum load and 230 VAC
Air performance measured
in H2O
Pa
Curves (2 Speed stages)
0,25
8
1110
170
1,36
66
1055
170
1,37
63
A
3
1030
170
1,38
61
and without protection against
A
4
980
170
1,40
60
accidental contact
A
5
935
100
0,86
63
A
6
915
110
0,93
61
A
7
905
115
0,97
59
A
8
885
122
1,04
59
LWA as per ISO 13347,
3
LpA measured at 1 m distance
to fan axis
40
The acoustic values given are
0,15
7
only valid under the measurment conditions listed and
30
may vary depending on the
2
0,10
installation situation.
6
With any deviation to the stan-
20
dard setup, the specific values
have to be checked and re-
0,05
10
viewed once installed or fitted!
For detailed information
psf
0
qV
28
500
1000
1000
1500
2000
2000
3000
2500
4000
see page 62 ff.
1
5
3000
5000
cfm
m3/h
LWA
dB(A)
2
Suction-side noise levels:
0,20
50
I
A
1
in ebm-papst full nozzle
A
Pe
W
A
Installation category A,
4
n
rpm
A
as per: ISO 5801,
70
60
2-stages / 0-10 V
Mass without
attachments
M3G 084-FA
Perm. amb. temp.
M3G 074-DF
*3G 450
Max. back pressure
*3G 450
B
2,7
Max.
current draw(1)
A
-25..+60
Max.
input power(1)
M3G 074-DF
70
Speed/rpm(1)
*3G 450
kg
Frequency
Motor
°C
Nominal
voltage range
Type
Pa
VAC
Curve
Nominal data
Technical features
and electr. connection
– Material: Guard grille: Steel, phosphated and coated in black plastic (RAL9005)
Wall ring: Sheet steel, pre-galvanised and coated in black plastic (RAL9005)
Blades: Plastic PP
Rotor: A B Surface passivated; C Surface coated in black
Electronics enclosure: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: A B IP 54; C IP 54 (acc. to EN 60529)
– Insulation class: "B"
– Mounting position: A B Any; C Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharge holes: A B None, open rotor; C Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Direction of air flow
– Technical features: See electrical connections p. 60 ff.
– EMC: Inerference immunity acc. to EN 61000-6-2 (industrial environment)
Harmonics acc. to EN 61000-3-2/3
Interference emission acc. to EN 61000-6-3 (household environment)
On account of the installation conditions, ferritic damping in the
connection line may be required for the application.
– Leakage current: < 3,5 mA A B acc. to EN 60335-1; C acc. to EN 61800-5-1
– Cable exit: Variable
– Terminal box design: Electrical connection via terminal strip
– Protection class: I; C acc. to EN 61800-5-1
– Product conforming to standards: A B EN 60335-1; C EN 61800-5-1
– Approvals: A B VDE, CURUS on request; C CSA; UL
❮ "V"
❮ "V"
Without
attachments
❮ "V"
With full
round nozzle
❮ "V"
With guard grille
for short nozzle
With guard grille for short nozzle
and mounted terminal box
"V"
A3G 450-AO02 -01
W3G 450-CO02 -30
S3G 450-AO02 -30
S3G 450-AO02 -50*
"V"
A3G 450-AO02 -03
W3G 450-CO02 -32
S3G 450-AO02 -32
S3G 450-AO02 -52*
"V"
A3G 450-AC28 -51
W3G 450-CC28 -51
S3G 450-LC28 -51
S3G 450-LC28 -59*
Direction of air flow "A" on request
*Terminal box design: Electrical connection via terminal strip
140
Air performance measured
in H2O
Pa
Curves (Speed-controlled)
as per: ISO 5801,
0,5
4
and without protection against
120
0,4
100
accidental contact
C
Pe
W
I
A
LWA
dB(A)
B
1
1110
170
1,36
66
B
2
1055
170
1,37
63
B
3
1030
170
1,38
61
B
4
980
170
1,40
60
Installation category A,
in ebm-papst full nozzle
n
rpm
C
1
1310
270
1,72
71
Suction-side noise levels:
C
2
1300
298
1,91
68
LWA as per ISO 13347,
C
3
1300
326
2,07
65
LpA measured at 1 m distance
C
4
1300
345
2,20
67
to fan axis
80
3
0,3
The acoustic values given are
B
4
only valid under the measurment conditions listed and
60
0,2
may vary depending on the
installation situation.
3
40
2
With any deviation to the standard setup, the specific values
2
0,1
have to be checked and reviewed once installed or fitted!
20
For detailed information
psf
0
qV
500
1000
1000
2000
1500
2000
3000
2500
4000
3000
5000
see page 62 ff.
1
1
3500
6000
cfm
m3/h
29
Drawings
p. 30 ff.
Electr. connections
p. 56/57/58
EC axial fans - HyBlade®
Ø 450 with motor M3G 074, 2 Speed stages, drawings for direction of air flow "V"
Type
Without attachments
Depth of screw
max. 10 mm
101±3
91±2
Mass
kg
A3G 450-AO02 -01
M6(4x)
M4(4x)
2,7
Depth of screw
max. 5 mm
Ø101
Ø75
Ø446±2
Ø58±0.2
Internal diameter of the
wall ring at least 454 mm
Ø90±0.2
20
0+
60 10
±
85
6
5
106±1
brass lead tips
crimped
❮ "V"
Type
With full round nozzle
35
Mass
kg
W3G 450-CO02 -30
101±3
100
7,4
15˚
Ø11
Ø607
Ø536
Ø467.5
˚
60
6x
78
Ø5
14
❮ "V"
Type
With guard grille for short nozzle
S3G 450-AO02 -30 4,80
S3G 450-AO02 -50* 4,95
5
❮ "V"
30
51±2
Tightening torque: 0,8 Nm±0,15 Nm
91
.5
Ø522
*Type with terminal
box:
Ø9+0.3
94
Ø477.2
51±3
85
Mass
kg
41
Internal diameter of the
wall ring at least 454 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
EC axial fans - HyBlade®
Ø 450 with motor M3G 074, Speed-controlled, drawings for direction of air flow "V"
Type
Without attachments
Depth of screw
max. 10 mm
101±3
91±2
Mass
kg
A3G 450-AO02 -03
M6(4x)
M4(4x)
2,7
Depth of screw
max. 5 mm
Ø101
Ø75
Ø446±2
Ø58±0.2
Internal diameter of the
wall ring at least 454 mm
Ø90±0.2
20
0+
60 10
±
85
6
5
106±1
brass lead tips
crimped
❮ "V"
Type
With full round nozzle
35
Mass
kg
W3G 450-CO02 -32
101±3
100
7,4
15˚
Ø11
60
6x
Ø607
Ø536
Ø467.5
˚
78
Ø5
14
❮ "V"
Type
With guard grille for short nozzle
S3G 450-AO02 -32 4,80
S3G 450-AO02 -52* 4,95
5
❮ "V"
51±2
Tightening torque: 0,8 Nm±0,15 Nm
91
.5
Ø522
*Type with terminal
box:
Ø9+0.3
94
Ø477.2
51±3
85
Mass
kg
41
Internal diameter of the
wall ring at least 454 mm
Cable diameter: 7,5 mm
Tightening torque: 2,0 Nm±0,3 Nm
31
EC axial fans - HyBlade®
Ø 450 with motor M3G 084, Speed-controlled, drawings for direction of air flow "V"
Type
Without attachments
Mass
kg
A3G 450-AC28 -51
M6(4x)
45˚
Depth of screw
8-10 mm
4x90˚
Ø446±2
Ø178
Ø150±0.25
Ø100
103.4±3
92.5±2
4,8
8
600±20
85±10
Internal diameter of the
wall ring at least 454 mm
47.7
Ø164±0.35
148±2
Core-end sleeve
crimped
❮ "V"
Type
With full round nozzle
Mass
kg
W3G 450-CC28 -51
156±3
100
6x6
Ø11
0˚
Ø465
Ø607
Ø536
9,5
78
Ø5
14
❮ "V"
Type
With guard grille for short nozzle
S3G 450-LC28 -51 6,80
S3G 450-LC28 -59* 6,95
❮ "V"
32
10
0
Ø522
Tightening torque: 1,5 Nm±0,2 Nm
0
5
*Type with terminal
box:
10
Ø477.3
53±3
98
Mass
kg
66.2
Ø9
Internal diameter of the
wall ring at least 454 mm
Cable diameter: min. 4 mm, max. 10 mm
Tightening torque: 2,5 Nm±0,4 Nm
33
34
AC axial fans - HyBlade® Ø 300-450
AC axial fans HyBlade® Ø 300-450
36
35
AC axial fans - HyBlade®
Ø 300
*4E 300(1)
M4E 068-CF
B
C
D
E
F
G
H
subject to alterations
Hz
rpm
W
A
μF/VDB
Pa
°C
kg
50
60
50
60
50
60
50
60
2580
2750
1300
1400
2700
3000
1320
1500
210
300
68
90
230
350
72
90
0,62/0,36
0,84/0,48
0,25/0,14
0,26/0,15
1,10
1,55
0,32
0,40
--------8,0/400
8,0/400
2,0/400
2,0/400
200
125
60
70
200
50
60
60
-25..+75
-25..+40
-25..+60
-25..+55
-25..+50
-25..+40
-25..+50
-25..+50
3,1
3,1
1,6
1,6
3,1
3,1
2,7
2,7
(1) Nominal data in operating point with maximum load and 230 or 400 VAC
Pa
0,8 in H2O
Air performance measured
as per: ISO 5801,
A
0,7
and without protection against
accidental contact
160
0,6
0,5
120
1
2580
210
0,62/0,36
78
2
2540
227
0,62/0,36
78
A
3
2490
244
0,68/0,39
77
A
4
2395
278
0,74/0,43
78
2750
300
0,84/0,48
80
2
2685
316
0,84/0,48
79
LWA as per ISO 13347,
B
3
2625
331
0,87/0,50
79
LpA measured at 1 m distance
B
4
2550
347
0,90/0,52
78
C
1
1350
55
0,23/0,13
59
C
2
1350
57
0,23/0,13
58
C
3
1335
61
0,23/0,13
58
C
4
1300
68
0,25/0,14
64
D
1
1500
70
0,23/0,13
62
D
2
1495
75
0,24/0,14
61
dard setup, the specific values
D
3
1460
80
0,24/0,14
61
have to be checked and re-
D
4
1400
90
0,25/0,15
66
0,4
0,3
installation situation.
D
With any deviation to the stan-
0,2
3
2
C
2
3
viewed once installed or fitted!
2
0,1
20
2
For detailed information
psf
1
0
qV
200
400
500
600
1000
800
1500
1000
1
1
1200
2000
1400
2500
1600
1800
3000
50 Hz
36
LWA
dB(A)
1
may vary depending on the
4
40
I
A
B
only valid under the measur-
3
4
Pe
W
B
The acoustic values given are
3
60
n
rpm
A
ment conditions listed and
80
p. 60 / A1)
to fan axis
4
B
100
p. 60 / A1)
Suction-side noise levels:
4
140
p. 61 / C1,C2)
A
Installation category A,
in ebm-papst full nozzle
180
p. 61 / C1,C2)
(2) 230 VAC Δ / 400 VAC Y
Curves
200
Electr. connection
Mass without
attachments
M2E 074-DF
Perm. amb. temp.
*2E 300
VAC
3~230/400
3~230/400
3~230/400
3~230/400
1~230
1~230
1~230
1~230
A
M4D 068-CF
Max. back pressure
*4D 300(1)(2)
Capacitor
M2D 074-DF
current draw
*2D 300(2)
input power
Motor
Speed/rpm
Typ
Frequency
Nominal data
Nominal voltage
Curve
– Material: Guard grille: Steel, phosphated and coated in black plastic (RAL9005)
Wall ring: Sheet steel, pre-galvanised and coated in black plastic (RAL9005)
Blades: C D G H Plastic PP; A B E F Sheet steel, coated in black
Rotor: Surface coated in black
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 44, depending on installation and position (acc. to EN 60034-5)
– Insulation class: A B "F"; C D E F G H "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharge holes: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
see page 62 ff.
1
cfm
m3/h
60 Hz
Motor protection: E F G H TOP wired internally
Leakage current: < 0,75 mA acc. to EN 60335-1
Cable exit: Variable
Terminal box design: Electrical connection via terminal strip
Protection class: I
Product conforming to standards: EN 60335-1; CE
Approvals: VDE, CURUS on request
Direction of air flow
–
–
–
–
–
–
–
❮ "V"
❮ "V"
Without
attachments
❮ "V"
With full
round nozzle
❮ "V"
With guard grille
for short nozzle
With guard grille for short nozzle
and mounted terminal box
"V"
A2D 300-AP02 -01
W2D 300-CP02 -30
S2D 300-AP02 -30
S2D 300-AP02 -50*
"V"
A4D 300-AS34 -01
W4D 300-CS34 -30
S4D 300-AS34 -30
S4D 300-AS34 -50*
"V"
A2E 300-AP02 -01
W2E 300-CP02 -30
S2E 300-AP02 -30
S2E 300-AP02 -50*(3)
"V"
A4E 300-AS72 -01
W4E 300-CS72 -30
S4E 300-AS72 -30
S4E 300-AS72 -50*(3)
*Terminal box design: Electrical connection via terminal strip
Direction of air flow "A" on request
(3) Device is outfitted with a P0 capacitor. EN 60335-1 is to be observed for the end application !
200
Air performance measured
0,8 in H2O
Pa
Curves
as per: ISO 5801,
E
0,7
180
and without protection against
accidental contact
4
0,6
0,5
120
1
2700
230
1,10
80
E
2
2680
255
1,12
79
E
3
2600
279
1,22
79
E
4
2520
303
1,32
79
1
3000
350
1,55
82
F
2
2940
355
1,58
81
LWA as per ISO 13347,
F
3
2885
362
1,60
81
LpA measured at 1 m distance
F
4
---
---
---
---
G
1
1380
62
0,28
60
G
2
1370
63
0,28
59
G
3
1355
66
0,29
58
G
4
1320
72
0,32
61
H
1
1590
80
0,36
63
H
2
1560
83
0,36
62
dard setup, the specific values
H
3
1535
86
0,37
62
have to be checked and re-
H
4
1500
90
0,40
62
to fan axis
3
0,4
only valid under the measurment conditions listed and
may vary depending on the
0,3
80
installation situation.
60
G
H
4
With any deviation to the stan-
3
40
3
3
viewed once installed or fitted!
0,1
20
F
2
0,2
4
LWA
dB(A)
F
The acoustic values given are
100
I
A
Suction-side noise levels:
160
140
Pe
W
E
Installation category A,
in ebm-papst full nozzle
n
rpm
2
2
2
For detailed information
psf
1
0
qV
500
500
1000
1
1000
1500
1
1500
2000
2500
2000
3000
3500
50 Hz
see page 62 ff.
1
cfm
m3/h
60 Hz
37
Drawings
p. 38 ff.
Capacitors
p. 54 ff.
Electr. connections
p. 60/61
AC axial fans - HyBlade®
Ø 300 with motor M4* 068, drawings for direction of air flow "V"
Typ
Without attachments
70.5±3
57.5±2
45˚
Depth of screw
max. 5 mm
Mass
kg
A4D 300-AS34 -01
A4E 300-AS72 -01
1,6
2,7
4x90˚
Ø80
Ø27
Ø300±1
M4(4x)
450+20
Internal diameter of the
wall ring at least 306 mm
6
85±10
2
brass lead tips
crimped
Ø58±0.2
73.4±1
❮ "V"
With full round nozzle
15˚
6x60˚
Ø9
Mass
kg
W4D 300-CS34 -30
W4E 300-CS72 -30
3,85
4,1
Typ
Mass
kg
Ø326
Ø397
87.3±2
80
Typ
80
Ø3
11
❮ "V"
With guard grille for short nozzle
S4D
S4E
S4D
S4E
300-AS34
300-AS72
300-AS34
300-AS72
-30
-30
-50*
-50*
94
Tightening torque: 0,7 Nm±0,2 Nm
.5
Ø360
*Type with terminal
box:
2,60
2,85
2,75
3,00
91
Ø330
20.5±3
±3
15.2
58.2
4.5
57.3
❮ "V"
38
23.5±2
Ø4.3
Internal diameter of the
wall ring at least 306 mm
Cable diameter: max. 7,5 mm
Tightening torque: 1,3 Nm±0,2 Nm
AC axial fans
Ø 300 with motor M2* 074, drawings for direction of air flow "V"
Typ
Without attachments
65±3
38±2
45˚
Depth of screw
max. 10 mm
Mass
kg
A2D 300-AP02 -01
A2E 300-AP02 -01
3,1
3,1
4x90˚
Ø101
Ø75
Ø298±2
M6(4x)
450+20
Internal diameter of the
wall ring at least 306 mm
85±10
5
6
104±2
brass lead tips
crimped
Ø90±0.2
❮ "V"
Typ
With full round nozzle
87.3±2
80
6x60˚
Ø9
W2D 300-CP02 -30
W2E 300-CP02 -30
5,2
5,2
Ø326
Ø397
15˚
Mass
kg
80
Ø3
11
104±2
❮ "V"
Typ
With guard grille for short nozzle
S2D
S2E
S2D
S2E
300-AP02
300-AP02
300-AP02
300-AP02
-30
-30
-50*
-50*
94
Tightening torque: 0,7 Nm±0,2 Nm
.5
Ø360
*Type with terminal
box:
4,10
4,10
4,25
4,25
91
Ø324.4
15±4
Mass
kg
76.5
55
5
54±2
❮ "V"
Ø6.5
Internal diameter of the
wall ring at least 306 mm
Cable diameter: max. 7,5 mm
Tightening torque: 1,3 Nm±0,2 Nm
39
AC axial fans - HyBlade®
Ø 350
W
*4D 350(2)
M4D 074-DF
*4E 350
A
B
3~230/400
3~230/400
1~230
50
60
50
1370
1520
1340
170
230
165
C
M4E 074-DF
*6E 350
D
1~230
1~230
50
60
910
1020
75
95
M6E 074-DF
subject to alterations
E
A
μF/VDB
Pa
°C
kg
0,64/0,37 --0,70/0,40 --0,73
4,0/400
90
90
90
-25..+65
-25..+55
-25..+65
3,5
3,5
3,5
40
50
-25..+50
-25..+55
3,5
3,5
0,35
0,42
(1) Nominal data in operating point with maximum load and 230 or 400 VAC
2,0/400
2,0/400
Pa
in H2O
Air performance measured
as per: ISO 5801,
0,4
and without protection against
accidental contact
90
4
4
0,3
70
A
1400
140
0,63/0,36
69
2
1395
147
0,63/0,36
66
A
3
1380
157
0,63/0,36
64
A
4
1370
170
0,64/0,37
64
185
0,63/0,36
72
1575
200
0,63/0,36
69
LWA as per ISO 13347,
B
3
1550
214
0,64/0,37
67
LpA measured at 1 m distance
B
4
1520
230
0,70/0,40
66
0,2
installation situation.
With any deviation to the stan-
2
2
0,1
dard setup, the specific values
have to be checked and re-
20
viewed once installed or fitted!
10
For detailed information
psf
0
qV
500
500
1000
1000
1500
1500
2000
2500
2000
3000
3500
50 Hz
see page 62 ff.
1
1
40
1
A
1600
may vary depending on the
30
cfm
m3/h
60 Hz
LWA
dB(A)
2
ment conditions listed and
40
I
A
1
only valid under the measur-
50
Pe
W
B
The acoustic values given are
3
n
rpm
B
to fan axis
3
60
p. 60 / A1)
Suction-side noise levels:
B
80
p. 60 / A1)
A
Installation category A,
in ebm-papst full nozzle
100
p. 61 / C1,C2)
(2) 230 VAC Δ / 400 VAC Y
Curves
110
Electr. connection
rpm
Mass without
attachments
Hz
Perm. amb. temp.
Motor
Max. back pressure
Max.
input power(1)
Typ
Capacitor
Speed/rpm(1)
Nominal data
Max.
current draw(1)
Frequency
VAC
Curve
Nominal voltage
– Material: Guard grille: Steel, phosphated and coated in black plastic (RAL9005)
Wall ring: Sheet steel, pre-galvanised and coated in black plastic (RAL9005)
Blades: Plastic PP
Rotor: Surface coated in black
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 44, depending on installation and position (acc. to EN 60034-5)
– Insulation class: A B C "F"; D E "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharge holes: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Motor protection: C D E TOP wired internally
Leakage current: < 0,75 mA acc. to EN 60335-1
Cable exit: Variable
Terminal box design: Electrical connection via terminal strip
Protection class: I
Product conforming to standards: EN 60335-1; CE
Approvals: VDE, CURUS on request
Direction of air flow
–
–
–
–
–
–
–
❮ "V"
❮ "V"
Without
attachments
❮ "V"
With full
round nozzle
❮ "V"
With guard grille
for short nozzle
With guard grille for short nozzle
and mounted terminal box
"V"
A4D 350-AN08 -01
W4D 350-CN08 -30
S4D 350-AN08 -30
S4D 350-AN08 -50*
"V"
A4E 350-AN02 -01
W4E 350-CN02 -30
S4E 350-AN02 -30
S4E 350-AN02 -50*(3)
"V"
A6E 350-AN24 -01
W6E 350-CN24 -30
S6E 350-AN24 -30
S6E 350-AN24 -50*(3)
Direction of air flow "A" on request
*Terminal box design: Electrical connection via terminal strip
(3) Device is outfitted with a P0 capacitor. EN 60335-1 is to be observed for the end application !
Air performance measured
in H2O
Pa
Curves
as per: ISO 5801,
90
in ebm-papst full nozzle
and without protection against
80
C
accidental contact
60
0,2
50
3
1400
135
0,60
69
2
1380
145
0,64
66
C
3
1365
155
0,68
64
C
4
1340
165
0,73
64
1
930
67
0,32
59
D
2
925
69
0,33
57
LWA as per ISO 13347,
D
3
915
72
0,34
54
LpA measured at 1 m distance
D
4
910
75
0,35
53
E
1
1090
83
0,37
62
E
2
1070
87
0,38
60
E
3
1050
90
0,39
58
E
4
1020
95
0,42
56
only valid under the measur-
E
ment conditions listed and
4
may vary depending on the
30
1
C
D
The acoustic values given are
3
D
LWA
dB(A)
to fan axis
4
40
I
A
Suction-side noise levels:
0,3
70
Pe
W
C
Installation category A,
4
n
rpm
installation situation.
2
3
0,1
With any deviation to the stan-
20
dard setup, the specific values
2
have to be checked and re2
viewed once installed or fitted!
10
For detailed information
psf
1
0
qV
500
500
1000
1000
1500
1
1500
2000
2500
see page 62 ff.
1
cfm
3000
50 Hz
m3/h
60 Hz
41
Drawings
p. 42
Capacitors
p. 54 ff.
Electr. connections
p. 60/61
AC axial fans - HyBlade®
Ø 350 with motor M** 074, drawings for direction of air flow "V"
Typ
Without attachments
45˚
M6(4x)
Depth of screw
max. 10 mm
A4D 350-AN08 -01
A4E 350-AN02 -01
A6E 350-AN24 -01
3,5
3,5
3,5
4x90˚
Ø352±2
Ø101
Ø75
97.3±3
87.3±2
Mass
kg
600+20
Internal diameter of the
wall ring at least 358 mm
85±10
5
6
105±2
brass lead tips
crimped
Ø90±0.2
❮ "V"
Typ
With full round nozzle
115±2
80
W4D 350-CN08 -30
W4E 350-CN02 -30
W6E 350-CN24 -30
30˚
Ø9
Mass
kg
6,4
6,4
6,5
Ø460
Ø403
Ø390
0˚
6x6
42
Ø4
12
97.3±3
140±2
❮ "V"
Typ
With guard grille for short nozzle
S4D
S4E
S6E
S4D
S4E
S6E
42
Tightening torque: 0,7 Nm±0,2 Nm
94
Ø422
*Type with terminal
box:
5,00
5,00
5,00
5,15
5,15
5,15
.5
55.3±2
❮ "V"
-30
-30
-30
-50*
-50*
-50*
31
5
85
350-AN08
350-AN02
350-AN24
350-AN08
350-AN02
350-AN24
91
Ø375
47.3±3
Mass
kg
Ø6.3
Internal diameter of the
wall ring at least 358 mm
Cable diameter: max. 7,5 mm
Tightening torque: 1,3 Nm±0,2 Nm
43
AC axial fans - HyBlade®
Ø 400
C
D
E
F
subject to alterations
Hz
rpm
W
A
μF/VDB
Pa
°C
kg
50
60
50
50
50
60
1450
1690
1430
1700
870
870
135
185
160
240
120
150
0,76/0,44
0,68/0,39
0,73
1,06
0,53
0,67
----6,0/400
6,0/400
3,0/400
3,0/400
150
120
150
75
40
40
-25..+40
-25..+40
-25..+40
-25..+40
-25..+60
-25..+45
4,2
4,2
4,1
4,1
3,7
3,7
(1) Nominal data in operating point with maximum load and 230 VAC
Pa
in H2O
Air performance measured
as per: ISO 5801,
0,6
and without protection against
accidental contact
0,5
4
B
1450
135
0,76/0,44
74
2
1435
161
0,81/0,47
73
A
3
1420
182
0,85/0,49
72
A
4
1410
203
0,87/0,50
74
185
0,68/0,39
76
1660
223
0,78/0,45
76
LWA as per ISO 13347,
B
3
1635
256
0,85/0,49
76
LpA measured at 1 m distance
B
4
1605
290
0,94/0,54
76
0,3
may vary depending on the
installation situation.
0,2
With any deviation to the stan2
40
dard setup, the specific values
2
0,1
have to be checked and reviewed once installed or fitted!
20
For detailed information
psf
1
0
qV
500
500
1000
1000
1500
1500
2000
2500
2000
3000
3500
see page 62 ff.
1
2500
4000
50 Hz
44
1
A
1690
ment conditions listed and
60
cfm
4500
m3/h
60 Hz
LWA
dB(A)
2
only valid under the measur-
3
I
A
1
The acoustic values given are
80
Pe
W
B
4
3
n
rpm
B
to fan axis
0,4
100
p. 60 / A1)
Suction-side noise levels:
A
120
p. 60 / A1)
A
Installation category A,
in ebm-papst full nozzle
140
p. 61 / C1,C2)
(2) 230 VAC Δ / 400 VAC Y
Curves
160
Electr. connection
Mass without
attachments
B
M6E 074-DF
Perm. amb. temp.
*6E 400(1)
VAC
3~230/400
3~230/400
1~230
1~230
1~230
1~230
A
M4E 074-EI
Max. back pressure
*4E 400
Capacitor
M4D 074-EI
current draw
*4D 400(2)
input power
Motor
Speed/rpm
Typ
Frequency
Nominal data
Nominal voltage
Curve
– Material: Guard grille: Steel, phosphated and coated in black plastic (RAL9005)
Wall ring: Sheet steel, pre-galvanised and coated in black plastic (RAL9005)
Blades: E F Plastic PP; A B C D Sheet steel, coated in black
Rotor: Surface coated in black
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 44, depending on installation and position (acc. to EN 60034-5)
– Insulation class: E F "F"; A B C D "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharge holes: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
Motor protection: C D E F TOP wired internally
Leakage current: < 0,75 mA acc. to EN 60335-1
Cable exit: Variable
Terminal box design: Electrical connection via terminal strip
Protection class: I
Product conforming to standards: EN 60335-1; CE
Approvals: VDE, CURUS on request
Direction of air flow
–
–
–
–
–
–
–
❮ "V"
❮ "V"
Without
attachments
❮ "V"
With full
round nozzle
❮ "V"
With guard grille
for short nozzle
With guard grille for short nozzle
and mounted terminal box
"V"
A4D 400-AP12 -01
W4D 400-CP12 -30
S4D 400-AP12 -03
S4D 400-AP12 -50*
"V"
A4E 400-AP02 -01
W4E 400-CP02 -30
S4E 400-AP02 -03
S4E 400-AP02 -50*(3)
"V"
A6E 400-AN24 -01
W6E 400-CN24 -30
S6E 400-AN24 -30
S6E 400-AN24 -50*(3)
*Terminal box design: Electrical connection via terminal strip
Direction of air flow "A" on request
(3) Device is outfitted with a P0 capacitor. EN 60335-1 is to be observed for the end application !
Air performance measured
in H2O
Pa
Curves
as per: ISO 5801,
0,6
in ebm-papst full nozzle
and without protection against
accidental contact
140
0,5
C
100
0,4
120
LWA
dB(A)
1
1430
160
0,73
74
C
2
1425
180
0,81
74
C
3
1405
198
0,88
73
C
4
1380
219
0,97
74
D
1
1700
240
1,06
78
Suction-side noise levels:
D
2
1675
255
1,13
77
LWA as per ISO 13347,
D
3
1645
271
1,19
77
LpA measured at 1 m distance
D
4
1620
286
1,25
76
E
1
900
110
0,49
63
E
2
900
110
0,49
61
E
3
890
114
0,50
58
E
4
870
120
0,53
59
F
1
990
145
0,64
65
F
2
955
148
0,64
63
dard setup, the specific values
F
3
920
149
0,65
59
have to be checked and re-
F
4
870
150
0,67
60
The acoustic values given are
only valid under the measur0,3
80
ment conditions listed and
4
3
D
may vary depending on the
installation situation.
0,2
60
3
With any deviation to the stan-
4
2
F
3 3
0,1
E
I
A
to fan axis
4
40
Pe
W
C
Installation category A,
160
n
rpm
2
viewed once installed or fitted!
20
2
2
For detailed information
psf
1
0
qV
500
500
1000
1000
1500
1500
2000
2500
1
2000
3000
3500
1
1
2500
4000
50 Hz
see page 62 ff.
cfm
4500
m3/h
60 Hz
45
Drawings
p. 46 ff.
Capacitors
p. 54 ff.
Electr. connections
p. 60/61
AC axial fans
Ø 400 with motor M4* 074, drawings for direction of air flow "V"
Typ
Without attachments
45˚
M6(4x)
Depth of screw
max. 10 mm
A4D 400-AP12 -01
A4E 400-AP02 -01
4,2
4,1
4x90˚
Ø101
Ø75
Ø392±2
94±3
68±2
Mass
kg
Internal diameter of the
wall ring at least 400 mm
85±10
600+20
5
6
117±2
brass lead tips
crimped
Ø90±0.2
❮ "V"
Typ
With full round nozzle
131±2
96
W4D 400-CP12 -30
W4E 400-CP02 -30
30˚
Ø9
Mass
kg
8,0
8,0
Ø528
Ø468
Ø419
0˚
6x6
04
Ø5
12
152±2
❮ "V"
Typ
With guard grille for short nozzle
S4D
S4E
S4D
S4E
400-AP12
400-AP02
400-AP12
400-AP02
-03
-03
-50*
-50*
Tightening torque: 0,7 Nm±0,2 Nm
.5
94
Ø470
*Type with terminal
box:
5,90
5,90
6,05
6,05
91
Ø415
24±4
Mass
kg
57
5
85
47±2
❮ "V"
46
Ø9
Internal diameter of the
wall ring at least 400 mm
Cable diameter: max. 7,5 mm
Tightening torque: 1,3 Nm±0,2 Nm
AC axial fans - HyBlade®
Ø 400 with motor M6E 074, drawings for direction of air flow "V"
Typ
Without attachments
A6E 400-AN24 -01
Depth of screw
max. 10 mm
86.6±3
88.6±2
Mass
kg
3,7
45˚
4x90˚
Ø392±2
Ø101
Ø75
M6(4x)
Internal diameter of the
wall ring at least 400 mm
6
85±10
600+20
5
105±2
brass lead tips
crimped
Ø90±0.2
❮ "V"
Typ
With full round nozzle
W6E 400-CN24 -30
131±2
96
Mass
kg
7,6
30˚
Ø9
Ø419
Ø528
Ø468
0˚
6x6
04
Ø5
12
140±2
❮ "V"
Typ
With guard grille for short nozzle
S6E 400-AN24 -30 5,40
S6E 400-AN24 -50* 5,55
Tightening torque: 0,7 Nm±0,2 Nm
94
Ø470
*Type with terminal
box:
.5
91
Ø414
37±3
36.5
5
85
Mass
kg
55±2
❮ "V"
Ø9
Internal diameter of the
wall ring at least 400 mm
Cable diameter: max. 7,5 mm
Tightening torque: 1,3 Nm±0,2 Nm
47
AC axial fans - HyBlade®
Ø 450
Mass without
attachments
Hz
rpm
W
A
μF/VDB
Pa
°C
kg
Δ
Y
Δ
Y
Δ
Y
Δ
Y
50
50
60
60
50
50
60
60
1250
875
1360
860
1360
1110
1510
1060
340
200
415
205
480
340
690
400
0,61
0,33
0,70
0,35
0,98
0,58
1,20
0,72
-----------------
120
60
85
35
140
90
145
70
-25..+60
-25..+60
-25..+50
-25..+50
-25..+65
-25..+65
-25..+50
-25..+50
4,9
4,9
4,9
4,9
7,5
7,5
7,5
7,5
E
F
G
H
Pa
in H2O
Air performance measured
as per: ISO 5801,
0,5
in ebm-papst full nozzle
A
4
and without protection against
110
0,4
accidental contact
90
4
80
0,49
73
262
0,52
74
A
3
1300
289
0,55
72
A
4
1250
340
0,61
72
1070
160
0,27
67
1015
172
0,29
66
LWA as per ISO 13347,
B
3
970
182
0,31
65
LpA measured at 1 m distance
B
4
875
200
0,33
65
C
1
1455
334
0,57
75
C
2
1415
359
0,61
75
C
3
1380
381
0,64
75
C
4
1360
415
0,70
73
D
1
990
187
0,31
65
D
2
940
192
0,32
64
dard setup, the specific values
D
3
900
197
0,33
63
have to be checked and re-
D
4
860
205
0,35
62
0,2
installation situation.
2
With any deviation to the stan-
4
2
0,1
3
20
2
D
viewed once installed or fitted!
2
10
For detailed information
1
psf
231
1320
ment conditions listed and
30
0
500
1000
1000
2000
1500
2000
3000
1
2500
4000
1
3000
5000
see page 62 ff.
1
3500
cfm
6000 m3/h
50 Hz
48
1350
2
2
3
qV
1
A
1
may vary depending on the
40
LWA
dB(A)
B
0,3
3
B
I
A
B
only valid under the measur4
Pe
W
Suction-side noise levels:
The acoustic values given are
60
n
rpm
to fan axis
C
3
70
50
p. 61 / F1b.F2b)
A
Installation category A,
120
100
p. 61 / F1b,F2b)
(1) Nominal data in operating point with maximum load and 400 VAC
Curves
130
Electr. connection
Perm. amb. temp.
C
D
subject to alterations
Max. back pressure
B
M4D 094-HA
VAC
3~400
3~400
3~400
3~400
3~400
3~400
3~400
3~400
A
*4D 450
Capacitor
M4D 094-EA
Max.
current draw(1)
*4D 450
Max.
input power(1)
Motor
Speed/rpm(1)
Typ
Frequency
Nominal data
Nominal voltage
Curve
– Material: Guard grille: Steel, phosphated and coated in black plastic (RAL9005)
Wall ring: Sheet steel, pre-galvanised and coated in black plastic (RAL9005)
Blades: Plastic PP
Rotor: Surface coated in black
Terminal box: Plastic ABS
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "F"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharge holes: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
60 Hz
Motor protection: Design with thermal overload protector
Leakage current: < 3,5 mA acc. to EN 61800-5-1
Electrical connection: Via terminal box
Protection class: I acc. to EN 61800-5-1
Product conforming to standards: EN 60034-1; CE
Approvals: A B C D CCC
Direction of air flow
–
–
–
–
–
–
❮ "V"
❮ "V"
Without
attachments
❮ "V"
With full
round nozzle
With guard grille
for short nozzle
"V"
A4D 450-AU01 -01
W4D 450-CU01 -01
S4D 450-AU01 -01
"V"
A4D 450-AO14 -01
W4D 450-CO14 -01
S4D 450-AO14 -01
Direction of air flow "A" on request
Air performance measured
in H2O
Pa
Curves
as per: ISO 5801,
4
140
in ebm-papst full nozzle
and without protection against
0,5
G
accidental contact
120
3
4
80
0,3
1400
386
0,88
71
2
1385
422
0,91
68
E
3
1370
453
0,95
68
E
4
1360
480
0,98
68
1
1195
285
0,49
68
F
2
1160
308
0,52
65
LWA as per ISO 13347,
F
3
1130
326
0,55
64
LpA measured at 1 m distance
F
4
1110
340
0,58
64
G
1
1575
580
1,02
73
G
2
1550
620
1,09
71
G
3
1530
657
1,15
70
G
4
1510
690
1,20
70
H
1
1175
375
0,65
67
H
2
1130
388
0,68
64
dard setup, the specific values
H
3
1095
398
0,70
63
have to be checked and re-
H
4
1060
400
0,72
62
only valid under the measur-
4
3
ment conditions listed and
may vary depending on the
60
installation situation.
0,2
1
E
F
The acoustic values given are
H
2
3
2
With any deviation to the stan-
40
2
0,1
LWA
dB(A)
to fan axis
3
F
I
A
Suction-side noise levels:
E
0,4
100
Pe
W
E
Installation category A,
4
n
rpm
2
viewed once installed or fitted!
20
For detailed information
psf
1
0
qV
500
1000
1000
2000
1500
2000
3000
2500
4000
3000
5000
3500
1
4000
6000
7000
50 Hz
1
see page 62 ff.
cfm
m3/h
60 Hz
49
Drawings
p. 52
Electr. connections
p. 61
AC axial fans - HyBlade®
Ø 450
rpm
W
A
*4E 450
M4E 094-EA
50
60
50
60
50
60
1300
1490
1310
1390
900
990
350
425
490
650
190
260
1,55
1,87
2,36
2,96
0,86
1,16
*4E 450
M4E 094-HA
*6E 450(2)
M6E 094-EA
subject to alterations
1~230
1~230
1~230
1~230
1~230
1~230
A
B
C
D
E
F
(1) Nominal data in operating point with maximum load and 230 VAC
μF/VDB
Pa
°C
kg
120
50
125
115
60
75
-25..+55
-25..+45
-25..+65
-25..+55
-25..+65
-25..+65
4,9
4,9
7,5
7,5
4,9
4,9
8,0/400
8,0/400
10,0/400
10,0/400
5,0/450
5,0/450
Pa
in H2O
Air performance measured
as per: ISO 5801,
0,5
C
120
in ebm-papst full nozzle
4
and without protection against
110
0,4
100
D
accidental contact
A
90
3
3
1380
272
1,20
74
2
1355
299
1,31
74
A
3
1340
321
1,40
73
A
4
1300
350
1,55
73
76
1545
396
1,74
2
1490
425
1,87
77
LWA as per ISO 13347,
B
3
---
---
---
---
LpA measured at 1 m distance
B
4
---
---
---
---
C
1
1350
430
2,10
69
C
2
1340
447
2,16
68
C
3
1325
470
2,26
68
C
4
1310
490
2,36
0,2
2
68
D
1
1480
600
2,70
72
D
2
1455
615
2,76
70
dard setup, the specific values
D
3
1415
637
2,87
70
have to be checked and re-
D
4
1390
650
2,96
69
installation situation.
2
2
With any deviation to the stanB
0,1
20
viewed once installed or fitted!
10
For detailed information
psf
0
qV
500
1000
1000
2000
1500
2000
3000
2500
4000
3000
5000
3500
1
1
4000
6000
7000
50 Hz
50
1
1
may vary depending on the
1
LWA
dB(A)
A
ment conditions listed and
30
I
A
B
only valid under the measur-
60
2
Pe
W
B
The acoustic values given are
40
n
rpm
to fan axis
3
70
50
p. 60 / A2c)
Suction-side noise levels:
0,3
80
p. 60 / A2b)
A
Installation category A,
4
4
p. 60 / A2c)
(2) ErP2013
Curves
130
Electr. connection
Hz
Mass without
attachments
Max.
current draw(1)
Motor
Perm. amb. temp.
Max.
input power(1)
Typ
Max. back pressure
Speed/rpm(1)
Nominal data
Capacitor
Frequency
VAC
Curve
Nominal voltage
– Material: Guard grille: Steel, phosphated and coated in black plastic (RAL9005)
Wall ring: Sheet steel, pre-galvanised and coated in black plastic (RAL9005)
Blades: Plastic PP
Rotor: Surface coated in black
Terminal box: Plastic ABS
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 54 (acc. to EN 60529)
– Insulation class: "F"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharge holes: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings
1
cfm
m3/h
60 Hz
see page 62 ff.
– Motor protection:
TOP wired internally
Design with thermal overload protector
Leakage current: < 3,5 mA acc. to EN 61800-5-1
Electrical connection: Via terminal box, capacitor integrated and connected
Protection class: I acc. to EN 61800-5-1
Product conforming to standards: EN 60034-1; CE
Approvals: CCC
C
Direction of air flow
–
–
–
–
–
A
B
E
F
D
❮ "V"
❮ "V"
Without
attachments
❮ "V"
With full
round nozzle
With guard grille
for short nozzle
"V"
A4E 450-AU03 -01
W4E 450-CU03 -01
S4E 450-AU03 -01
"V"
A4E 450-AO09 -01
W4E 450-CO09 -01
S4E 450-AO09 -01
"V"
A6E 450-AU04 -01
W6E 450-CU04 -01
S6E 450-AU04 -01
Direction of air flow "A" on request
n
rpm
Air performance measured
in H2O
Pa
Curves
as per: ISO 5801,
4
F
in ebm-papst full nozzle
50
accidental contact
3
1
925
171
0,79
61
E
2
915
180
0,82
60
E
3
905
186
0,84
59
E
4
900
190
0,86
59
F
1
1060
241
1,05
64
F
2
1035
251
1,09
63
LWA as per ISO 13347,
F
3
1015
260
1,13
62
LpA measured at 1 m distance
F
4
990
260
1,16
62
to fan axis
E
The acoustic values given are
3
0,15
40
LWA
dB(A)
Suction-side noise levels:
4
0,20
60
0,25
and without protection against
I
A
E
Installation category A,
70
Pe
W
only valid under the measurment conditions listed and
may vary depending on the
30
0,10
installation situation.
2
20
With any deviation to the stan-
2
dard setup, the specific values
0,05
10
have to be checked and reviewed once installed or fitted!
For detailed information
psf
1
0
qV
500
1000
1000
1500
2000
2000
3000
2500
4000
see page 62 ff.
1
3000
5000
50 Hz
cfm
m3/h
60 Hz
51
Drawings
p. 53
Capacitors
p. 54 ff.
Electr. connections
p. 60
AC axial fans - HyBlade®
Ø 450 with motor M** 094, drawings for direction of air flow "V"
Typ
Without attachments
Depth of screw
max. y mm
c±3
d±2
A4D 450-AU01 -01
A4D 450-AO14 -01
45˚
Mass
kg
c
d
g
y
4,9
7,5
77
104
76,5
98
107
148
10
12
w
x
4x90˚
Ø124
Ø446±2
Ø101
M6(4x)
Internal diameter of the
wall ring at least 454 mm
Kabelverschraubung
5.5
88
Ø115±0.35
g±2
38.5
❮ "V"
With full round nozzle
w±2
100
Ø11
15˚
Mass
kg
W4D 450-CU01 -01
W4D 450-CO14 -01
9,6 135 145,5
12,5 146,5 186,5
Typ
Mass
kg
u
s
v
S4D 450-AU01 -01
S4D 450-AO14 -01
7,2
10,0
26,5
41
88,5
101
57
85
Ø465
Ø607
Ø537
0˚
6
6x
Typ
78
Ø5
14
x±2
❮ "V"
With guard grille for short nozzle
Ø515
Ø473
u±3
Internal diameter of the
wall ring at least 454 mm
6
s
v±2
❮ "V"
52
Ø9
AC axial fans - HyBlade®
Ø 450 with motor M4* 094, drawings for direction of air flow "V"
Typ
Without attachments
Depth of screw
max. y mm
M6(4x)
c
d
g
y
7,5
4,9
4,9
104
77
98
98
76,5
98
148
107
107
12
10
10
w
x
Ø124
Ø446±2
c±3
d±2
A4E 450-AO09 -01
A4E 450-AU03 -01
A6E 450-AU04 -01
Mass
kg
Internal diameter of the
wall ring at least 454 mm
Kabelverschraubung
5.5
99
Ø115±0.3
g±2
65.5
❮ "V"
With full round nozzle
w±2
100
Ø11
15˚
Mass
kg
W4E 450-CO09 -01
W4E 450-CU03 -01
W6E 450-CU04 -01
12,7 146,5 213,5
9,6 135 172,5
9,6 135 172,5
Typ
Mass
kg
u
s
v
S4E 450-AO09 -01
S4E 450-AU03 -01
S6E 450-AU04 -01
10,0
7,5
7,0
41
24
49
128,5
115,5
116
85
57
57
Ø465
Ø607
Ø537
˚
60
6x
Typ
78
Ø5
14
x±2
❮ "V"
With guard grille for short nozzle
Ø522
Ø473
u±3
Internal diameter of the
wall ring at least 454 mm
6
s
v±2
Ø9
❮ "V"
53
Capacitors
b
c ±10
7 ±1
Øa
M8
10
MKP motor capacitors P0 (without fuse)
Part no.
Capacity
a
b (max.)
c
99283-4-7320
2,0 μF
25-28
58,0
235,0
68462-4-7320
3,0 μF
25-28
70,0
235,0
99284-4-7320
4,0 μF
28-32
58,0
235,0
02101-4-7320
5,0 μF
30-36
70,0
235,0
99285-4-7320
6,0 μF
30-36
70,0
235,0
99286-4-7320
8,0 μF
35-40
72,0
235,0
99287-4-7320
10,0 μF
35-40
72,0
200,0
subject to alterations
54
– Material: Housing made of thermoplastic resin
– Connection line: Multi-lead
PVC cable 0.5 mm2 with brass lead tips
– Approval: VDE according to DIN EN 60252
(VDE 0560/8)
– Calculated life time:
400 V; -25 to +85°C; 30,000 hrs; class A
450 V; -25 to +85°C; 10,000 hrs; class B
Capacitors
c
– Material: Plastic cap, aluminium cup
– Designation: FPU or P2 according to
IEC 252 (non-flammable, non-explosive,
circuit-breaking)
– Approval: VDE according to DIN EN 60252
(VDE 0560/8)
– Calculated life time:
420 V; -25 to +85°C; 30,000 hrs; class A
470 V; -25 to +85°C; 10,000 hrs; class B
500 V; -25 to +85°C; 3,000 hrs; class C
b
Øa
M8
Ø a + 3,5
10
7 ±1
35 +5
235 +10
-5
MKP motor capacitors FPU or P2 (with fuse)
Part no.
Capacity
a
b (max.) c (max.)
02156-4-7320
2,0 μF
25,0
77,0
02160-4-7320
3,0 μF
30,0
71,0
92,0
02161-4-7320
4,0 μF
25-30
104,0
135,0
02162-4-7320
5,0 μF
25-30
104,0
113,0
02163-4-7320
6,0 μF
30,0
101,0
110,0
02165-4-7320
8,0 μF
30-35
102,0
111,0
02166-4-7320
10,0 μF
35,0
96,0
110,0
92,0
max. 9 mm
subject to alterations
– Pull-off protector: The housing expands
by max. 9 mm. The protector responds to
overload by the generated excess pressure
snapping off the internal lead in a predetermined breaking point.
– Mounting: c is the overall dimension of the
capacitor which has to be taken into account
when mounting the part. The capacitor
design, however, depends on the manufacturer. The expansion (9 mm) is either added
to dimension b, or it is already integrated in
the capacitor.
55
Electrical connections EC
H3)
Technical features:
• Speed adjustment input (230V)
• Electronics / motor overtemperature protection
• Motor current limitation
• Locked rotor protection
• Soft start
H3) EC motors M3G 055 / M3G 074 (2 Speed stages)
Customer circuit
Connection
Fan / Motor
L
AC1
P
N
AC2
N
CON10
CON11
SL
CON70
PE
CON10
CON11
CON70
CON70
CON12
Line
Connection
Colour
Assignment / function
CON10
L
black
Power supply 230 VAC, 50 - 60 Hz, see type plate for voltage range
CON11
N
blue
Neutral conductor
CON12
PE
green/yellow
Protective earth
CON70
SL
brown
Speed selection: switch open = speed 1; switch closed = speed 2
56
PE1
Electrical connections EC
H4)
Technical features:
• Control input 0-10 VDC / PWM
• Output 10 VDC max. 1,1 mA
• Tach output
• Electronics / motor overtemperature protection
• Motor current limitation
• Locked rotor protection
• Soft start
H4) EC motors M3G 055 / M3G 074 (Speed-controlled)
Customer circuit
max.
speed
Connection
speed
setting
Fan / Motor
L
AC1
P
N
AC2
N
CON10
3
2
CON11
PE
1-10V
CON12
2
1
PE1
10V -> n = max
1V -> n = min
<1V -> n = 0
+10V
1
3
2
4
3
Imax=1.1mA
10V/PWM
2
47k
Speed
setting with
PWM 1-10kHz
Speed
setting with
potentiometer
47k
1μF
GND
1
15V
Tach
3
4
680R
Imax=10mA
3
1
4
2
ZMM47
2
2
10K
12V
1
1
100% PWM -> n = max
10% PWM -> n = min
<10% PWM -> n = 0
Line
Connection
Colour
Assignment / function
CON10
L
black
Power supply 230 VAC, 50 - 60 Hz, see type plate for voltage range
CON11
N
blue
Neutral conductor
CON12
PE
green/yellow
Protective earth
1
GND
blue
GND - Connection for control interface
2
0-10V PWM
yellow
Control input 0 - 10 V or PWM, electrically isolated
3
10V/max.1.1mA
red
Voltage output 10V / 1.1mA, electrically isolated, not short-circuit-proof
4
Tach
white
Tach output: Open Collector, 1 pulse per revolution, electrically isolated
57
Electrical connections EC
K1)
Technical features:
• Control input 0-10 VDC / PWM
• Output 10 VDC max. 1,1 mA
• Alarm relay
• Electronics / motor overtemperature protection
• Line undervoltage detection
• Motor current limitation
• Soft start
K1) EC motors M3G 084 (Speed-controlled)
Notes on various control possibilities and their applications
Umin = 15 V
Imax =
10 mA
Mains
50/60 Hz
PWM
+
-
NC
white1
COM
white2
Voltage output
red
+10 V
max. 1.1 mA
+
U
-
10 K
L
black
N
blue
PE
green/yellow
12 V
Alarm relay:
Break for failure
(2 A, 250 VAC, AC1)
Lin/PWM control input
yellow
0-10 VDC /
PWM
1 μF
GND
blue
Speed setting
PWM 1 - 10 kHz
Speed setting
with variable
resistance
Speed setting
Full speed
1 V - 10 V
10 V -> n=max
approx. 1 V -> n=min
< 1 V -> n=0
100% PWM -> n=max
approx. 10% PWM -> n=min
< 10% PWM -> n=0
start up at > 1.4 V
start up at > 14%
Customer circuit
Connection
+10 V
0-10 V
PWM
GND
green/yellow white1
COM
blue
Line 2
NC
N
black
PE
L
Line 1
Fan
white2
red
yellow
blue
Line
Connection Colour Assignment / function
Line
Connection Colour Assignment / function
1
L
black
Mains 50/60 Hz, phase
2
+10 V
N
blue
Mains 50/60 Hz, neutral
0-10 V / PWM yellow
Control input (Impedance 100 kΩ)
PE
green/yel
Protective earth
GND
GND
NC
white1
Alarm relay, break for failure
COM
white2
Alarm relay, COMMON
58
red
blue
Voltage output +10 V max. 1.1 mA
59
Electrical connections AC
A1) Single-phase capacitor motor
with TOP wired internally
N
PE
L
C
U2 Z
U1
U1 = blue
U2 = black
Z = brown
= green/
yellow
TOP
A2b) Single-phase capacitor motor
with connection for external TOP
C
U1 Z U2
L
N PE
Fans
with terminal box
60
TOP TOP
U1 = blue
U2 = black
Z = brown
= green/
yellow
A2c) Single-phase capacitor motor
without TOP
C
U1 Z U2
L
N PE
Fans
with terminal box
U1 = blue
U2 = blsck
Z = brown
= green/
yellow
Electrical connections AC
C1) Delta connection (3~ 230 VAC power line)*
without TOP
L1
PE
L2
U1
V1
U2
V2
without TOP
U1
U2
V1
V2
W1
W2
L3
W1
W2
=
=
=
=
=
=
=
black
green
blue
white
brown
yellow
green/
yellow
F1b) Delta connection*
L2
U1
V1
W1
U2
V2
W2
L3
U1
U2
V1
V2
W1
W2
=
=
=
=
=
=
=
black
green
blue
white
brown
yellow
green/
yellow
U1
U2
V1
V2
W1
W2
=
=
=
=
=
=
=
black
green
blue
white
brown
yellow
green/
yellow
with TOP
U1 V1 W1 W2 U2 V2 TOP TOP
Fans
with terminal box
L1
PE
F2b) Star connection*
with TOP
L1 L2 L3
C2) Star connection (3~ 400 VAC power line)*
PE
U1
U2
V1
V2
W1
W2
=
=
=
=
=
=
=
black
green
blue
white
brown
yellow
green/
yellow
U1 V1 W1 W2 U2 V2 TOP TOP
L1 L2 L3
Fans
with terminal box
PE
*Direction of rotation is reversed by swapping two line phases.
61
Technical parameters & scope
High standards for all ebm-papst products
Here at ebm-papst, we constantly strive to further improve our products in order to be able to offer you the best
possible product for your application. Careful monitoring of the market ensures that technical innovations are
reflected in the improvements of our products.
Based on the technical parameters listed below and the ambience you want our product to operate in,
we here at ebm-papst can always work out the best solution for your specific application.
General performance parameters
Service life
Any deviations from the technical data and parameters described here
The service life of ebm-papst products depends on two major factors:
are listed on the product-specific data sheet.
– The service life of the insulation system
Type of protection
The service life of the insulation system mainly depends on voltage level,
The type of protection is specified in the product-specific data sheets.
temperature and ambient conditions, such as humidity and condensation.
– The service life of the bearing system
The service life of the bearing system depends mainly on the thermal load
Insulation class
on the bearing.
The insulation class is specified in the product-specific data sheets.
The majority of our products use maintenance-free ball bearings for
any mounting position possible. As an option, sleeve bearings can be
Mounting position
used, which is indicated on the product-specific data sheet wherever
The mounting position is specified in the product-specific data sheets.
applicable.
The service life L10 of the ball bearings can be taken as approx. 40,000
Condensate discharge holes
operating hours at an ambient temperature of 40 °C, yet this estimate
Information on the condensate discharge holes is provided in the
can vary according to the actual ambient conditions.
product-specific data sheets.
We will gladly provide you with a lifetime calculation taking into account
your specific operating conditions.
Mode of operation
The mode of operation is specified in the product-specific data sheets.
Motor protection / thermal protection
Information on motor protection and thermal protection is provided in the
Protection class
product-specific data sheets.
The protection class is specified in the product-specific data sheets.
Depending on motor type and field of application, the following protective
features are realised:
– Thermal overload protection (TOP), either in-circuit or external
– PTC with electronic diagnostics
– Impedance protection
– Thermal overload protection (TOP) with electronic diagnostics
– Current limitation via electronics
If an external TOP is connected, the customer has to make sure to
connect a conventional trigger device for switching it off.
Products without fitted TOP and without protection against improper use,
a motor protection complying with the valid standards has to be installed.
62
Left: Endurance test room
Middle: Shock test
Right: Chamber test rig
Mechanical strain / performance parameters
Legal and normative directives
All ebm-papst products are subjected to comprehensive tests complying
The products described in this catalogue are designed, developed and
with the normative specifications. In addition to this, the tests also reflect
produced in keeping with the standards in place for the relevant product
the vast experience and expertise of ebm-papst.
and, if known, the conditions governing the relevant fields of application.
Vibration test
Standards
Vibration tests are carried out in compliance with
Information on standards is provided in the product-specific data sheets.
– Vibration test in operation according to DIN IEC 68, parts 2-6
– Vibration test at standstill according to DIN IEC 68, parts 2-6
EMC
Information on EMC standards is provided in the product-specific data
Shock load
sheets.
Shock load tests are carried out in compliance with
Complying with the EMC standards has to be established on the final
– Shock load according to DIN IEC 68, parts 2-27
appliance, as different mounting situations can result in changed EMC
properties.
Balancing quality
Testing the balancing quality is carried out in compliance with
Leakage current
– Residual imbalance according to DIN ISO 1940
Information on the leakage current is provided in the product-specific
– Standard balancing quality level G 6.3
data sheets.
Should you require a higher balancing quality level for your specific
Measuring is according to IEC 60990.
application, please let us know and specify this when ordering your
product.
Approvals
In case you require a specific approval for your ebm-papst product
Chemo-physical strain / performance parameters
(VDE, UL, GOST, CCC, CSA, etc.) please let us know.
Should you have questions about chemo-physical strain, please direct
Most of our products can be supplied with the relevant approval.
them to your ebm-papst contact.
Information on existing approvals is provided in the product-specific
data sheets.
Fields of application, industries and applications
Our products are used in various industries and applications:
Air performance measurements
Ventilation, air-conditioning and refrigeration technology, clean room
All air performance measurements are carried out on suction side and on
technology, automotive and rail technology, medical and laboratory tech-
chamber test beds conforming to the specifications as per ISO 5801 and
nology, electronics, computer and office technology, telecommunications,
DIN 24163. The fans under test are installed in the measuring chamber at
household appliances, heating, machines and plants, drive engineering.
free air intake and exhaust (installation category A) and are operated at
Our products are not designed for use in the aviation and aerospace
nominal voltage, with AC also at nominal frequency, and without any
industry!
additional components such as guard grilles.
As required by the standard, the air performance curves correspond to
an air density of 1.2 kg/m3.
63
Room for precision noise measuring
Measurement conditions for air and noise measurement
ebm-papst products are measured under the following conditions:
– Axial and diagonal fans in direction of rotation “V” in full nozzle and
without guard grille
– Backward curved centrifugal fans, free-running and with inlet nozzle
– Forward curved single and dual inlet centrifugal fans with housing
Noise measurements
All noise measurements are carried out in low-reflective test rooms with
reverberant floor. Thus the ebm-papst acoustic test chambers meet the
requirements of precision class 1 according to DIN EN ISO 3745. For noise
measurement, the fans being tested are placed in a reverberant wall and
operated at nominal voltage (for AC, also at nominal frequency) without
additional attachments such as the guard grille.
Sound pressure level and sound level
All acoustic values are established according to ISO 13347, DIN 45635
and ISO 3744/3745 to accuracy class 2 and given in A-rated form.
When the sound pressure level (Lp) is measured, the microphone is on
the intake side of the fan being tested, usually at a distance of 1 m on
the fan axis.
To measure the sound power level (Lw), 10 microphones are distributed
over an enveloping surface on the intake side of the fan being tested
(see graphic). The sound power level measured can be roughly calculated
1,5d
from the sound pressure level by adding 7 dB.
D
Measuring configuration as per ISO 13347-3 respectively DIN 45635-38:
10 measuring points
d≥D
h = 1,5d ... 4,5d
h
3d
Measurement area S = 6d2 + 7d (h + 1,5d)
2d
64
15
dB
Adding multiple noise sources with the same level
pressure level of a fan is approximately 75 dB(A). The level increase measured from the diagram is 9 dB. Thus the overall sound level of the installation can be expected to be 84 dB(A).
10
9
Example: 8 A3G800 axial fans are on a condenser. According to the data sheet, the sound
5
the noise values specified in the data sheet. This is shown in the diagram opposite.
0
The noise characteristics of multiple identical fans can be determined in advance based on
Increase in sound pressure / sound power level
Adding 2 noise sources with the same volume results in a level increase of approx. 3 dB.
1
2
3
4
5
6 7 8 9 10
15
20 25
3
Adding two noise sources with different levels
[dB]
Number of sources of sound with identical level
4 dB. The level increase can now be read in the diagram as approx. 1.5 dB. This means that
the overall sound level of the unit can be expected to be 76.5 dB(A).
2
1,5
ating point and an axial fan A3G710 with 71 dB(A) in a ventilation unit. The level difference is
1
Example: There is an axial fan A3G800 with a sound pressure level of 75 dB(A) at the oper-
0
levels given in the data sheet. This is shown in the diagram opposite.
Increase in sound pressure / sound power level
The acoustic performance of two different fans can be predetermined based on the sound
0
4
8
12
16
20
24
[dB]
0
Distance laws
[dB]
Difference in level with two sources of sound
Sound power level is independent of distance to the sound source. In contrast to this, sound
-10
pressure level decreases the further away the noise source is. The adjacent diagram shows
the decrease in level under far sound field conditions. Far sound field conditions apply when-
decreases by 6 dB. In the near field of the fan, other correlations apply and the decrease in
levels can be considerably smaller. The following example only applies to far sound field
conditions and can vary strongly depending on the installation effects:
With an axial fan A3G300, a sound pressure level of 65 dB(A) was measured at a distance of
1 m. According to the adjacent diagram, at a distance of 20 m we would get a reduction by
-20
-26
-30
vant literature on this complex topic. Per doubling of distance, the level in the far sound field
-40
wavelength to be considered. For more information on far sound field, please consult the rele-
Decrease in sound pressure level
ever the distance between microphone and fan is big when compared to fan diameter and
1
Distance
2
5
10
20
50
100
[m]
26 dB, i.e. a sound pressure level of 39 dB(A).
65
fan agent
compact fan agent
ebm-papst in Germany
motor specialist
motor agent
Germany
ebm-papst
Mulfingen GmbH & Co. KG
ebm-papst
St. Georgen GmbH & Co. KG
ebm-papst
Landshut GmbH
Bachmühle 2
D-74673 Mulfingen
Phone +49 7938 81-0
Fax +49 7938 81-110
[email protected]
Hermann-Papst-Straße 1
D-78112 St. Georgen
Phone +49 7724 81-0
Fax +49 7724 81-1309
[email protected]
Hofmark-Aich-Straße 25
D-84030 Landshut
Phone +49 871 707-0
Fax +49 871 707-465
[email protected]
www.ebmpapst.com
www.ebmpapst.com
www.ebmpapst.com
66
Berlin
Dipl.-Ing. (TH) Jens Duchow
Händelstraße 7
D-16341 Panketal
Phone +49 30 944149-62
Fax +49 30 944149-63
[email protected]
Heilbronn / Heidelberg
Dipl.-Ing. Mark Gartner
Gehrweg 12
D-74199 Unterheinriet
Phone +49 7130 404569-1
Fax +49 7130 404569-2
[email protected]
Bielefeld
Dipl.-Ing. (FH) Wolf-Jürgen Weber
Niehausweg 13
D-33739 Bielefeld
Phone +49 5206 91732-31
Fax +49 5206 91732-35
[email protected]
Kassel
Dipl.-Ing. (FH) Ralph Brück
Hoherainstraße 3 b
D-35075 Gladenbach
Phone +49 6462 4071-10
Fax +49 6462 4071-11
[email protected]
Dortmund
Dipl.-Ing. (FH) Hans-Joachim Pundt
Auf den Steinern 3
D-59519 Möhnesee-Völlinghausen
Phone +49 2925 800-407
Fax +49 2925 800-408
[email protected]
Koblenz
Winfried Schaefer
Hinter der Kirch 10
D-56767 Uersfeld
Phone +49 2657 16-96
Fax +49 2657 16-76
[email protected]
Frankfurt
Dipl.-Ing. Christian Kleffmann
Dr.-Hermann-Krause-Straße 23
D-63452 Hanau
Phone +49 6181 1898-12
Fax +49 6181 1898-13
[email protected]
Munich
Dipl.-Wirt.-Ing. (FH) Jens Peter
Landsbergerstraße 14
D-86932 Pürgen
Phone +49 8196 99877-54
Fax +49 8196 99877-55
[email protected]
Halle
Dipl.-Ing. (TU) Michael Hanning
Lercheneck 4
D-06198 Salzatal / OT Lieskau
Phone +49 345 55124-56
Fax +49 345 55124-57
[email protected]
Nuremberg
Dipl.-Wirt.-Ing. (FH) Axel Resch
Steinsfeldstraße 80
D-74626 Bretzfeld
Phone +49 7946 94401-02
Fax +49 7946 94401-03
[email protected]
Hamburg
Ingenieurbüro Breuell GmbH
Ing. Dirk Kahl
Elektroingenieur
Grützmühlenweg 48
D-22339 Hamburg
Phone +49 40 538092-19
Fax +49 40 538092-84
[email protected]
Offenburg
Dipl.-Ing. (FH) Ralf Braun
Hubeneck 21
D-77704 Oberkirch
Phone +49 7802 9822-52
Fax +49 7802 9822-53
[email protected]
Stuttgart
Dipl.-Ing. (FH) Rudi Weinmann
Hindenburgstraße 100/1
D-73207 Plochingen
Phone +49 7153 9289-80
Fax +49 7153 9289-81
[email protected]
Ulm
M.Sc. Reinhard Sommerreißer
Am Silbermannpark 10
D-86161 Augsburg
Phone +49 821 6610-7023
Fax +49 821 6610-7024
[email protected]
Distributors
Frankfurt
R.E.D. Handelsgesellschaft mbH
Gutenbergstraße 3
D-63110 Rodgau - Jügesheim
Phone +49 6106 841-0
Fax +49 6106 841-111
[email protected]
www.red-elektromechanik.de
Hamburg
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 48
D-22339 Hamburg
Phone +49 40 538092-20
Fax +49 40 538092-84
[email protected]
Munich
A. Schweiger GmbH
Ohmstraße 1
D-82054 Sauerlach
Phone +49 8104 897-0
Fax +49 8104 897-90
[email protected]
www.schweiger-gmbh.com
(1 to 5 pieces)
North
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 48
D-22339 Hamburg
Phone +49 40 538092-20
Fax +49 40 538092-84
[email protected]
South
HDS Ventilatoren Vertriebs GmbH
Glaswiesenstraße 1
D-74677 Dörzbach
Phone +49 7937 80355-20
Fax +49 7937 80355-25
[email protected]
www.hds-gmbh.net
ebm-papst in Europe
Europe
Austria
ebm-papst Motoren & Ventilatoren GmbH
Straubingstraße 17
A-4030 Linz
Phone +43 732 321150-0
Fax +43 732 321150-20
[email protected]
www.ebmpapst.at
Belarus
ebm-papst Bel AgmbH
P.O. Box 117
BY-220138 Minsk
Phone +375 17 3851556
Fax +375 17 3851556
[email protected]
www.ebmpapst.by
Belgium
ebm-papst Benelux B.V.
Sales office Belgium-Luxemburg
Romeinsestraat 6/0101
Research Park Haasrode
B-3001 Heverlee-Leuven
Phone +32 16 396-200
Fax +32 16 396-220
[email protected]
www.ebmpapst.be
Bulgaria
ebm-papst Romania S.R.L.
Str. Tarnavei No. 20
RO-500327 Brasov
Phone +40 268 331859
Fax +40 268 312805
[email protected]
Croatia
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Czech Republic / Slovakia
ebm-papst CZ s.r.o.
Kaštanová 34a
CZ-620 00 Brno
Phone +420 544 502-411
Fax +420 547 232-622
[email protected]
www.ebmpapst.cz
Denmark
ebm-papst Denmark ApS
Vallensbækvej 21
DK-2605 Brøndby
Phone +45 43 631111
Fax +45 43 630505
[email protected]
www.ebmpapst.dk
Estonia
ebm-papst Oy, Eesti Filiaal
Kesk tee 13
Aaviku küla, Jüri Tehnopark
EST-75301 Rae Vald, Harjumaa
Phone +372 65569-78
Fax +372 65569-79
www.ebmpapst.ee
Finland
ebm-papst Oy
Puistotie 1
FIN-02760 Espoo
Phone +358 9 887022-0
Fax +358 9 887022-13
[email protected]
www.ebmpapst.fi
France
ebm-papst sarl
ZI Nord - rue A. Mohler
BP 62
F-67212 Obernai Cedex
Phone +33 820 326266
Fax +33 3 88673883
[email protected]
www.ebmpapst.fr
Greece
Helcoma
Th. Rotas & Co OE
Davaki 65
GR-17672 Kallithea-Attiki
Phone +30 210 9513-705
Fax +30 210 9513-490
[email protected]
www.helcoma.gr
Hungary
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Iceland
RJ Engineers
Stangarhyl 1a
IS-110 Reykjavik
Phone +354 567 8030
Fax +354 567 8015
[email protected]
www.rj.is
Ireland
ebm-papst UK Ltd.
Chelmsford Business Park
GB-Chelmsford Essex CM2 5EZ
Phone +44 1245 468555
Fax +44 1245 466336
[email protected]
www.ebmpapst.co.uk
AuBren Limited
Portlaoise Business & Technology Park
Mountrath Road
IRL-Portlaoise, Co. Laois
Phone +353 57 8664343
Fax +353 57 8664346
[email protected]
www.aubren.com
Italy
ebm-papst Srl
Via Cornaggia 108
I-22076 Mozzate (Co)
Phone +39 0331 836201
Fax +39 0331 821510
[email protected]
www.ebmpapst.it
Macedonia
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
67
fan agent
compact fan agent
ebm-papst in Europe
motor specialist
motor agent
Netherlands
ebm-papst Benelux B.V.
Engelseweg 127
NL-5705 AC Helmond
Phone +31 492 502-900
Fax +31 492 502-950
[email protected]
www.ebmpapst.nl
Russia
ebm-papst Ural GmbH
Posadskaja-Strasse, 23(E), 3
RU-620102 Ekaterinburg
Phone +7 343 2338000
Fax +7 343 2337788
[email protected]
www.ebmpapst.ur.ru
Switzerland
ebm-papst AG
Rütisbergstrasse 1
CH-8156 Oberhasli
Phone +41 44 73220-70
Fax +41 44 73220-77
[email protected]
www.ebmpapst.ch
Norway
ebm-papst AS
P.B. 173 Holmlia
N-1203 Oslo
Phone +47 22 763340
Fax +47 22 619173
[email protected]
www.ebmpapst.no
ebm-papst Rus GmbH
proezd 4529, vladenie 5, stroenie 1
RU-141000 Mytistschi, Oblast Moskau
Phone +7 495 9807524
Fax +7 495 5140924
[email protected]
www.ebmpapst.ru
Turkey
Akantel Elektronik San. Tic. LTD. Sti.
Atatürk Organize Sanayi
Bölgesi 10007 SK. No.:6
TR-35620 Cigli-Izmir
Phone +90 232 3282090
Fax +90 232 3280270
[email protected]
www.ebmpapst.com.tr
Poland
ebm-papst Polska Sp. z o.o.
ul. Annopol 4A
PL-03236 Warszawa
Phone +48 22 6757819
Fax +48 22 6769587
[email protected]
www.ebmpapst.pl
Portugal
ebm-papst (Portugal), Lda.
Centro Empresarial de Alverca
Rua de Adarse, Vale D’Ervas
Corpo D / Fracção 3
P-2615-178 Alverca do Ribatejo
Phone +351 218 394 880
Fax +351 218 394 759
[email protected]
www.ebmpapst.pt
Romania
ebm-papst Romania S.R.L.
Str. Tarnavei Nr. 20
RO-500327 Brasov
Phone +40 268 331859
Fax +40 268 312805
[email protected]
68
Serbia & Montenegro
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Spain
ebm-papst Ibérica S.L.
Avda. del Sistema Solar, 29
E-28830 San Fernando de Henares (Madrid)
Phone +34 91 6780894
Fax +34 91 6781530
[email protected]
www.ebmpapst.es
Sweden
ebm-papst AB
Äggelundavägen 2
S-17562 Järfälla
Phone +46 10 4544400
Fax +46 8 362306
[email protected]
www.ebmpapst.se
Ukraine
ebm-papst Ukraine LLC
Lepse Boulevard, 4, Building 47
UA-03067 Kiev
Phone +38 044 2063091
Fax +38 044 2063091
[email protected]
www.ebmpapst.ua
United Kingdom
ebm-papst UK Ltd.
Chelmsford Business Park
GB-Chelmsford Essex CM2 5EZ
Phone +44 1245 468555
Fax +44 1245 466336
[email protected]
www.ebmpapst.co.uk
ebm-papst Automotive & Drives (UK) Ltd.
The Smithy
Fidlers Lane
GB-East Ilsley, Berkshire RG20 7LG
Phone +44 1635 2811-11
Fax +44 1635 2811-61
A&[email protected]
www.ebmpapst-ad.com
ebm-papst in America and Africa
America
Argentina
ebm-papst de Argentina S.A.
Hernandarias 148 Lomas del Mirador
Pcia. de Buenos Aires (1752)
Phone +54 11 46576135
Fax +54 11 46572092
[email protected]
www.ebmpapst.com.ar
Brazil
ebm-papst Motores Ventiladores Ltda.
Av. José Giorgi, 301 Galpões B6+B7
Condominio Logical Center
BR-06707-100 Cotia - São Paulo
Phone +55 11 4613-8700
Fax +55 11 4777-1456
[email protected]
www.ebmpapst.com.br
USA
ebm-papst Inc.
P.O. Box 4009
100 Hyde Road
USA-Farmington, CT 06034
Phone +1 860 674-1515
Fax +1 860 674-8536
[email protected]
www.ebmpapst.us
ebm-papst Automotive & Drives, Inc.
3200 Greenfield, Suite 255
USA-Dearborn, MI 48120
Phone +1 313 406-8080
Fax +1 313 406-8081
[email protected]
www.ebmpapst-automotive.us
Africa
South Africa
ebm-papst South Africa (Pty) Ltd.
P.O. Box 3124
1119 Yacht Avenue
ZA-2040 Honeydew
Phone +27 11 794-3434
Fax +27 11 794-5020
[email protected]
www.ebmpapst.co.za
Canada
ebm-papst Canada Inc.
1800 Ironstone Manor, Unit 2
CDN-Pickering, Ontario, L1W3J9
Phone +1 905 420-3533
Fax +1 905 420-3772
[email protected]
www.ebmpapst.ca
Mexico
ebm Industrial S. de R.L. de C.V.
Paseo de Tamarindos 400-A-5to Piso
Col. Bosques de las Lomas
MEX-Mexico 05120, D.F.
Phone +52 55 3300-5144
Fax +52 55 3300-5243
[email protected]
www.ebmpapst.com.mx
69
fan agent
compact fan agent
ebm-papst in Asia and Australia
motor specialist
motor agent
Asia
China
ebm-papst Ventilator (Shanghai) Co., Ltd.
No. 418, Huajing Road
WaiGaoQiao Free Trade Zone
No. 2001, Yang Gao (N) Road
VRC-200131 Shanghai, P.R. of China
Phone +86 21 5046-0183
Fax +86 21 5046-1119
[email protected]
www.ebmpapst.com.cn
Hong Kong
ebm-papst Hong Kong Ltd.
Unit No. 13,9 / F
Technology Park, 18 On Lai Street
Siu Lek Yuen, Shatin N.T.
Hong Kong - P.R. of China
Phone +852 2145-8678
Fax +852 2145-7678
[email protected]
India
ebm-papst India Pvt. Ltd.
26/3, G.N.T. Road, Erukkencherry
IND-Chennai-600118
Phone +91 44 25372556
Fax +91 44 25371149
[email protected]
www.ebmpapst.in
Indonesia
ebm-papst Indonesia
Representative Office
German Centre, 4th Floor, Suite 4470
Jl. Kapt. Subijono Dj. Bumi Serpong Damai
RI-15321 Tangerang
Phone +62 21 5376250
Fax +62 21 5388305
[email protected]
Israel
Polak Bros. Import Agencies Ltd.
9 Hamefalsim Street
IL-Kiryat Arie, Petach-Tikva 49514
Phone +972 3 9100300
Fax +972 3 5796679
[email protected]
www.polak.co.il
70
Japan
ebm-papst Industries Japan K.K.
12th Floor, Benex S-3 Bldg.
3-20-8 Shinyokohama, Kohoku-ku
J-222-0033 Yokohama
Phone +81 45 47057-51
Fax +81 45 47057-52
[email protected]
www.ebmpapst.jp
Thailand
ebm-papst Thailand Co., Ltd.
99/9 Moo 2, Central Chaengwattana Tower
14th Floor, Room 1402
Chaengwattana Road Bangtarad, Pakkret
THA-11120 Nonthaburi
Phone +66 2 8353785-7
Fax +66 2 8353788
[email protected]
Korea
ebm-papst Korea Co. Ltd.
6F, Trutec Bldg.
B 6-2, Digital Media City (DMC)
Sangam-Dong, Mapo-Gu
ROK-Seoul 121-270
Phone +82 2 366213-24
Fax +82 2 366213-26
[email protected]
www.ebmpapst.co.kr
United Arab Emirates
ebm-papst Middle East FZE
PO Box 17755
Jebel Ali Free Zone / FZS1 / AP05
UAE-Dubai
Phone +971 4 88608-26
Fax +971 4 88608-27
[email protected]
www.ebmpapst.ae
Malaysia
ebm-papst Malaysia
Representative Office
Unit 12-2, Jalan USJ Sentral 3
Persiaran Subang, Selangor Darul Ehsan
MAL-47600 Subang Jaya
Phone +60 3 8024-1680
Fax +60 3 8024-8718
[email protected]
Singapore
ebm-papst SEA Pte. Ltd.
No. 23 Ubi Road 4
#06-00 Olympia Industrial Building
SGP-Singapore 408620
Phone +65 65513789
Fax +65 68428439
[email protected]
Taiwan
ETECO Engineering & Trading Corp.
10F-I, No. 92, Teh-Wei Str.
RC-Tsow-Inn District, Kaohsiung
Phone +886 7 557-4268
Fax +886 7 557-2788
[email protected]
www.ebmpapst.com.tw
Vietnam
ebm-papst Vietnam
Representative Office
Room #102, 25 Nguyen Van Thu Street
District 1
VN-Ho Chi Minh City
Phone +84 8 39104099
Fax +84 8 39103970
[email protected]
Australia
Australia
ebm-papst A&NZ Pty Ltd.
10 Oxford Road
AUS-Laverton North, Victoria, 3026
Phone +61 3 9360-6400
Fax +61 3 9360-6464
[email protected]
www.ebmpapst.com.au
New Zealand
ebm-papst A&NZ Pty Ltd.
102 Henderson Valley Road
NZ-Henderson, Auckland 1230
Phone +64 9 837-1884
Fax +64 9 837-1899
[email protected]
www.ebmpapst.com.au
71
37872-7-8811 · KD-03/12-3’
Printed in Germany
ebm-papst
Mulfingen GmbH & Co. KG
Bachmühle 2
D-74673 Mulfingen
Phone +49 7938 81-0
Fax +49 7938 81-110
[email protected]
www.ebmpapst.com