QE-155 series - Leber Ingenieure

155W 2 & 3 Outputs with Battery Charger Function
QE-155 series
Features:
Universal AC input / Full range
Auto switch when power off (UPS function)
Built-in constant current limit circuit
Alarm signal for AC OK and Battery low
(TTL open collector output or relay contact output)
Protection: SCP, OLP, OVP
Brown-out (Low AC Input Voltage)
Battery low protection
Battery polarity protection (by Resettable Fuses)
Withstand 2G vibration test
3 years warranty
QE-155-G
MODEL
Output
Input
Output Number
DC Voltage Range
Rated Current
Max. Output Current
Rated Power
Ripple & Noise (Max.)
Voltage Adj. Range
Voltage Tolerance
Line Regulation
Load Regulation
Setup, Rise Time
Hold up Time (Typ.)
Voltage Range
Power Factor (Typ)
Frequency Range
Efficiency (Typ.) at 230VAC
AC Current (Typ.)
Inrush Current (Typ.)
Leakage Current
QE-155-GB
QE-155-L
QE-155-LB
CH1
CH2
CH1
CH2
CH3
CH1
CH2
CH1
CH2
CH3
13.8V
13.8V
13.8V
13.8V
5V
27.6V
27.6V
27.6V
27.6V
5V
7.5A
3.7A
6.4A
3.7A
3A
3.6A
2A
3.1A
2A
3A
3.88A
10.1A
3.88A
3A
5.6A
2.1A
5.1A
2.1A
3A
Note.8 11.2A
154.38W
Note.11 154.56W
154.56W
155.76W
Note.2 100mVp-p 150mVp-p 100mVp-p 150mVp-p 100mVp-p 100mVp-p 150mVp-p 100mVp-p
CH1: ±10%
150mVp-p 100mVp-p
CH1: ±10%
Note.3 ±2%
—
±2%
—
±3%
±2%
—
±2%
—
±3%
Note.4 ±0.5%
—
±0.5%
—
±0.5%
±0.5%
—
±0.5%
—
±0.5%
Note.5 ±0.5%
—
±0.5%
—
±1.5%
±0.5%
—
±0.5%
—
±1.5%
2400ms, 20ms / 230VAC, 3200ms, 20ms / 115VAC at full load
30ms / 230VAC, 30ms / 115VAC at full load
90 ~ 264VAC, 127 ~ 373VDC (Withstand 300VAC surge for 5sec. Without damage)
PF > 0.94 at full load
47 ~ 63Hz
86%
85%
86%
85%
2.5A / 115VAC, 1.5A / 230VAC
Cold Start 55A / 115VAC, 108A / 230VAC
For earth < 1mA / 264VAC
Above 110% rated output power CH1 / CH3 (GB / LB only)
Over Load
Protection
Over Voltage
Function
Battery cut off
AC OK
Battery Low
Working Temp.
Working Humidity
Environment Storage Temp. & Humidity
Temp. Coefficient
Vibration
Safety Standards
Withstand Voltage
Isolation Resistance
Safety & EMC
EMI Conduction & Radiation
Harmonic Current
EMS Immunity
Dimension (WxHxD)
Others
Packing
Note
Above 100% rated output current for CH2
Protection type: Hiccup mode, recovers automatically after fault condition is remove
CH1: 115 ~ 150% rated output voltage
Protection type: latch-off mode
10V ±4%
20V ±5%
TTL open collector output Relay contact output
TTL open collector output Relay contact output
Battery low voltage < 12V ±3%
Battery low voltage < 22V ±3%
-20 ~ +70°C (Refer to de-rating curve)
20 ~ 90% RH non-condensing
-40 ~ +85°C, 10 ~ 90% RH
±0.03% / °C (0 ~ 50°C) on CH1
10 ~ 500Hz, 2G 10min. / 1cycle, period for 60min. each along X, Y, Z axes
Certified UL 60950-1; EN 60950-1
I/P-O/P: 3KVAC, I/P-FG: 1.5KVAC, O/P-FG: 0.5KVAC
I/P-O/P: 100M Ohms / 500VDC
Certified EN 55022; EN 61000-6-3
Certified EN 61000-3-2; EN 61000-3-3
Certified IEC 61000-4-2, 3, 4, 5, 6, 8, 11; ENV 50204; EN 55024; EN 61000-6-1; EN 61204-3
98x38x179 mm / 3.858x1.496x7.047 inch
0.64kg; 24pcs / 15.36kg / 1.29CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uF & 47uF parallel capacitor.
3. Tolerance: includes setup time tolerance, line regulation and load regulation.
4. Line regulation is measured from low line to high line at rated load.
5. Load regulation is measured from 10% to 100% rated load.
6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
7. Length of setup time is measured at first cold start. Turning ON/OFF the power supply continuously may increase the setup time.
8. The total power output must not exceed the rated power.
9. CH2: Battery discharge current must not exceed 40% of the rated power.
10. Do not connect the GND port with B- port in your application to prevent product damage.
11. Please refer to the de-rating curve for the rated power.
REV. A8
14/02/16
1
QE-155 series
155W 2 & 3 Outputs with Battery Charger Function
Mechanical Drawings:
Unit : mm[inch]
101 [3.976]
60 [2.362]
FAN
Air flow direction
R1.75 [R0.069]
3.75
[0.148]
30
[1.181]
98 [3.858]
91.25 [3.593]
65 [2.559]
63 [2.48]
51.5 [2.028]
5 [0.197]
22
[0.866]
3.75 [0.148]
117 [4.606]
6.5 [0.256]
R1.75 [R0.069]
3-M3
38 [1.496]
29 [1.142]
18
[0.709]
19.5
[0.768]
29 [1.142]
Φ3.5 [Φ0.138]
13.15 [0.518]
179 [7.047]
QE-155-G/L
Alarm output Connector (CN2): JST B3B-XH or equivalent
Terminal Pin No. Assignment (CN1)
Assignment
Pin No.
Assignment
Pin No.
1
AC/L
5
DC output V+
2
AC/N
6
BAT+
3
FG
7
BAT-
8
DC/DC Output +5V
(GB/LB only)
DC Output com
4
Assignment
Pin No.
1
2
BAT LOW
G (13.8V/20mA)
L (27.6V/20mA)
3
Mating Housing
Terminal
JST XHP-3
or equivalent
JST
SXH-001 T-P0.6
or equivalent
AC OK
QE-155-GB/LB
Alarm output Connector (CN2): JST B4B-XH or equivalent
Assignment
Pin No.
1 2
Mating Housing
Terminal
JST XHP-4
or equivalent
JST
SXH-001 T-P0.6
or equivalent
AC OK
3 4
Bat. Low
De-rating Curve:
Load V.S Temp.
Load V.S I/P Voltage
100
Ta=25°C
100
80
LOAD (%)
LOAD (%)
With 23 CFM min.
With no Fan
60
40
20
-20
80
60
40
20
0
10
20
30
40
50
60
AMBIENT TEMPERATURE (°C)
70 (HORIZONTAL)
90
95
100
105
110
115
120
264
INPUT VOLTAGE (VAC) 60Hz
REV. A8
14/04/16
2
155W 2 & 3 Outputs with Battery Charger Function
QE-155 series
For QE-155-G/L:
Block Diagram
AC OK
ALARM
CIRCUIT
I/P
EMI FILTER
&
RECTIFIER
PFC
CONTROL
Bat. Low
V+
RECTIFIERS
&
FILTER
POWER
SWITCHING
COM
B+
O.L.P.
FG
DETECTION
CIRCUIT
B-
PWM
CONTROL
START
CIRCUIT
Battery Charger
&
Back up Control
O.V.P.
Alarm Signal for AC OK and Battery Low
(1)Alarm Signal is sent out through "AC OK" & "Battery Low" pins.
(2)An external voltage source is required for this function. The maximum applied voltage is 50V and the maximum sink current is 30mA.
(3)Table 3.1 explain the alarm function built-in the power supply.
Function
Description
Output of alarm
The signal is "Low" when the power supply
turns on
Low
(0.3V max. at 30mA)
The signal turns to be "High" when the power
supply turns OFF
High or open (External applied
voltage 50V max.)
The signal is "Low" when the voltage of
battery is under G:12V, L:22V
Low
(0.3V max. at 30mA)
The signal is "High" when the voltage of
battery is above G:12V, L: 22V
High or open (External applied
voltage 50V max.)
AC OK
Battery
Low
Table 3.1 Explanation of Alarm Signal
AC OK (Battery low)
V+
CN2 Pin3
G: 13.8V/20mA
L: 27.6V/20mA
CN2 Pin1(Pin2)
CN2 Pin3
R
V
or
CN1 Pin4 DC output GND
Internal circuit of AC OK (Battery Low)
CN2 Pin1(Pin2)
External voltage and R
(The max. sink is 30mA and 50V)
REV. A8
14/04/16
3
155W 2 & 3 Outputs with Battery Charger Function
QE-155 series
For QE-155-GB/LB:
Block Diagram
AC OK
ALARM
CIRCUIT
Bat. Low
DC/DC
Power Supply
I/P
EMI FILTER
&
RECTIFIER
PFC
CONTROL
+5V
V+
RECTIFIERS
&
FILTER
POWER
SWITCHING
COM
B+
FG
O.L.P.
START
CIRCUIT
DETECTION
CIRCUIT
PWM
CONTROL
O.V.P.
B-
Battery Charger
&
Back up Control
Alarm Signal for AC OK and Battery Low
(1)Alarm Signal is sent out through "AC OK" & "Battery Low" pins. (relay contact type)
(2)An external voltage source is required for this function. The maximum applied voltage is 30V and the maximum sink current is 1A.
(3)Table 4.1 explain the alarm function built-in the power supply.
AC OK (Battery low)
Function
Description
Output of alarm
The signal is “Low” when the power supply
turns on
Low or short
The signal turns to be “High” when the power
supply turns OFF
High or open (External applied
voltage 30V max.)
The signal is “Low” when the voltage of
battery is under GB:12V, LB:22V
Low or short
The signal is “High” when the voltage of
battery is above GB:12V, LB:22V
High or open (External applied
voltage 30V max.)
CN2 Pin1 (Pin3)
AC OK
Battery
Low
Table 4.1 Explanation of Alarm Signal
External voltage source (V)
and resistor (R)
(The max. sink is 1A and 30V)
Internal circuit of AC OK (Battery Low)
CN2 Pin2 (Pin4)
REV. A8
14/04/16
4