Primary

Packing List
Before you begin installing your card, please make sure that the
following materials have been shipped:
• 1 PCI-6871 all-in-one single board computer
• 1 startup manual
• CD-ROM or disks for utility, drivers, and manual (in PDF format)
• 1 power cable p/n: 1703080101
• Parallel port: One parallel port, supports SPP/EPP/ECP
mode
• Keyboard/mouse connector: Supports standard PC/AT keyboard and a PS/2 mouse
• Power management: Supports power saving modes including Normal/Standby/Suspend modes. APM 1.2 compliant
• Watchdog timer: 62 level timer intervals
• 1 PS/2 KB/M cable p/n : 1700060202
• USB: Four universal serial bus ports
• 1 Printer cable p/n :1700260250
• 1 FDD cable p/n :1701340603
• PC/104 expansion: PC/104 connector for ISA and PCI control board
• 1 EIDE cable p/n :1701400452
Solid State Disk
If any of these items are missing or damaged, contact your distributor or sales representative immediately.
• Supports one 50-pin socket for CFC type I/II
Note: For detailed contents of the PCI-6871, please refer to the
enclosed CD-ROM or disk (in PDF format).
Specifications
• CPU: VIA Eden 400MHz (PCI-6871F-J0A1)
VIA Eden 677 MHz (PCI-6871F-M0A1)
• System chipset:VIA VT8606"TwisterT"+VT82C686B
• BIOS: Award 256 KB Flash memory
• System memory: Two 144-pin SODIMM socket (on the
backside), accept 32 MB~1024MB, (512MBx2) SDRAM
• 2nd cache memory: 64 KB on the processor
• Enhanced IDE interface: Supports two Enhanced IDE channels. Primary Channel supports ATA-100 mode; secondary
Channel only supports ATA-33 and PIO mode. CFC card
occupies secondary slave.
• FDD interface: Supports up to two FDDs
• Serial ports: Two serial RS-232 ports. COM1:RS232,COM2:RS-232/422/485
VGA/LCD Interface
• Chipset: VIA VT8606"TwisterT" chip with integrated
Savage4 2D/3D/Video Accelerator
• Frame buffer: Supports 8/16/32MB frame buffer with system memory
• Interface: 4X AGP VGA/LCD interface: support for 9, 12,
15, 18, 24, 36 bit TFT and optional 16- or 24-bit DSTN panel
• Display modes:
CRT Modes: 1280 x 1024@16bpp (60 Hz),
1024 x 768 @16bpp (85 Hz),
800 x 600@16bpp(60Hz)
LCD/Simultaneous Modes:
1280 x 1024@16bpp (60Hz)
1024 x 768 @16bpp (60Hz)
LVDS: Supports 2-channel (2x18bit)LVDS interface
Ethernet interface
• Chipset: RTL 8139C
• Ethernet interface: IEEE 802.3u 10/100BASE-T Fast Ethernet compatible
• I/O address switchless setting
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our support website at:
http://support.advantech.com
This manual is for the PCI-6871 series, Rev. A1.
Printed in Taiwan
1
PCI-6871 Startup Manual
• Dimensions (L x W): 146 x 105 mm (5.75” x 4.13”)
• Power supply voltage: +5 V, +12 V ± 5%
http://www.advantech.com/epc
Part No. 200K687100
Mechanical and Environmental
2nd Edition
May, 2004
• Power requirements:
Max: 10.33A @ +5V, 205mA@+12V (with 128 MB SDRAM,
VIA C3-400MHz CPU)
Typical:2.37A @ +5V, 34.02mA@+12V (with 256 MB SDRAM,
VIA C3-400MHz CPU)
• Operating temperature: 0 ~ 60°C (32 ~ 140°F)
• Weight: 0.27 kg (weight of total package)
PCI-6871 PCIEden400 SlotPC SODIMM/VGA/LCD/LVDS/8139/CFC2
PCI-6871 PCI Eden400/Eden667 SlotPC SODIMM/VGA/
LCD/LVDS/8139/CFC2
Startup Manual
Jumpers and Connectors
The board has a number of jumpers and connectors that allow
you to configure your system to suit your application.
The tables below list the function of each jumper and connector.
Jumpers
Function
CMOS clear
LAN power select
RS-232/422/485 select
Watch-Dog output selct
Panel type select
Label
JP1
JP2
JP3
JP4
S1
JP1
1-2
2-3
CMOS clear
normal*
clear CMOS
normal*
3
JP2
1-3, 2-4
3-5, 4-6
2
clear CMOS
1
3
LAN power select
normal power*
WOL power
normal power*
2
1
WOL power
PCI-6871 Jumpers
JP3
1-2
3-4
5-6
RS-232*
RS-232/422/485 select
RS-232 *
RS-422
RS-485
RS-422
RS-485
JP4
1-2
2-3
Watch-Dog output select
reset
IRQ11
reset*
IRQ11
1
2
2
3
PCI-6871 Startup Manual
1
2
3
Label
CN1
CN2
CN3
CN4
CN5
CN6
CN7
CN8
CN9
CN10
CN11
CN12
CN13
CN14
CN15
CN16
CN17
CN18
CN19
CN20
CN21
CN23
CN24
CN25
CN26
CN27
CN28
FAN
Connectors
Function
Primary IDE
LPT
ATX Suspend PWR
USB1,2
PWR_SW
Floppy
Secondary IDE
Reset
IR CON
Audio I/F
MAIN PWR CON
D-SUB VGA
HDD, PWR LED CON & WDT Output
DIO CON
LAN RJ45 CON
PC104
LCD CON2 (10*2)
LCD CON1 (20*2)
COM1
COM2
LVDS CON
USB3,4
LCD back Light
PS/2 KB/MS
EXT_KB
LCD INV PWR
CF CON
CPU fan power
PCI-6871 Connectors
PCI-6871 Dimensions (component side)
PCI-6871 Dimensions (solder side)
PCI-6871 Startup Manual
3