• Infrared port: Shared with COM2. Transfer rates up to 4 Mbps Packing list Before you begin installing your card, please make sure that the following materials have been shipped: • 1 PCM-5864/5864L All-in-one single board computer • 1 Start-up manual • Keyboard/mouse connector: Supports standard PC/AT keyboard and a PS/2 mouse • Power management: Supports power saving modes including Normal/Standby/Suspend modes. APM 1.1 compliant • Watchdog timer: 63 level timer intervals • 1 CPU cooling fan • CD-ROM or Disks for utility, drivers, and manual (in PDF format) • USB: 2 Universal Serial Bus ports Solid state disk If any of these items are missing or damaged, contact your distributor or sales representative immediately. Note: For detailed contents of the PCM-5864/5864L, please refer to the enclosed CD-ROM or Disk (in PDF format).- For more information on this and other Advantech products, please visit our website at: • Supports one 50-pin socket for CompactFlash card VGA/LCD Interface • Chipset: C&T 69000 2 MB SDRAM on chip • Interface: PCI interface, 64-bit engine • Display mode: Flat panel displays up to 800 x 600 @ 24 bpp, 1024 x 768 @ 16 bpp. CRT monitors up to 800 x 600 @ 24 bpp, 1024 x 768 @ 16 bpp http://www.advantech.com http://www.advantech.com/epc LVDS interface (PCM-5864 only) For technical support and service, please visit our support website at: • Interface: 18 low-voltage TTL data channel meets ANSI EIA/TIA-644 • Chipset: TI SN75LVDS81 or NS DS90CR5803 http://support.advantech.com This manual is for the PCM-5864/5864L Rev. A1 or higher. Audio function (PCM-5864 only) Part No. 2006586410 Printed in Taiwan • AC97 compatible, integrated 3D audio 1st edition July1999 Specifications • Interface: Mic in, Line in, CD audio in, Line out, Speaker out Video in/ Video out (PCM-5864 only) Standard SBC functions • Chipset: Philips SDA 7111A for Video in; analog device AD725AR for TV out • CPU: Socket 7 for Intel® Pentium®, Pentium® MMX, AMD K6-II processor • Connectors: Pin header via optional cable connects to RCA connector or S-video connector • BIOS: Award 256 KB Flash memory • Format: NTSC or PAL , YUV 422 quality with RGB 16 format. Supports live video capture up to 10 ~ 15 fps at 320 x 240 resolution • System memory: One 168-pin DIMM socket accepts 16 up to 128 MB SDRAM • Enhanced IDE interface: One channel for two EIDE devices. BIOS auto-detect, PIO Mode 3 or Mode 4, UDMA/33 transfer. One channel for CFC Mechanical and environmental • FDD interface: Supports up to two FDDs • Power supply voltage: +5 V ± 5% • Serial ports: Four serial RS-232 ports with +5 V or +12 V power capabilities, COM 1,3,4: RS-232, COM2: RS232/422/485 • Power requirements: 7 A @ +5 V • Parallel port: One parallel port, supports SPP/EPP/ECP mode • Weight: 0.7 kg (weight of total package) • Dimension (L x W): 203 mm x 146 mm (8" x 5.75") • Operating temperature: 0 ~ 60° C PCM-5864 Pentium® SBC with VGA LCD/Ethernet/LVDS/Audio PCM-5864/5864L Pentium®SBC with VGA LCD/Ethernet/LVDS/Audio Start-up Manual Jumpers and connectors The board has a number of jumpers that allow you to configure your system to suit your application. The table below lists the function of each of the board jumpers and connectors: CN30 CN501 CN502 Video in (capture) CompactFlash connector Speaker out connector (for video play back) DIMM socket ATX power feature connector LVDS connector DIM1 J1 JP3 CPU voltage setting (J3) Jumpers Label J3 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 J15 J16 J17 J18 J19 J20 J21 J22 J23 J25 JP1 JP2 Function CPU voltage setting CPU frequency ratio setting Reserved Clear CMOS Backlight signal select System/PCI clock setting PCI clock setting COM4 RI pin setting COM3 RI pin setting CompactFlash enable/disable COM1 RI pin setting COM2 RI pin setting LCD power select Reserved Buzzer enable setting COM2 RS-232/422/485 setting COM2 RS-232/422/485 setting COM2 RS-232/422/485 setting Shift clock setting Audio power source setting TV out format select ATX power switch Watchdog timer action J3 must be set to match the CPU type. The chart below shows the proper jumper settings for their respective VCC (CORE). The VCC (I/O) for the CPU is fixed to be 3.3 V. J3: CPU voltage setting V CC (CORE) NONE 2.10 V 2.20 V 2.30 V 2.40 V 2.50 V 2.60 V 2.70 V 2.80 V 2.90 V 3.00 V 3.10 V 3.20 V 3.30 V 3.40 V 3.50 V 1-2 open closed open closed open closed open closed open closed open closed open closed open closed 3-4 open open closed closed open open closed closed open open closed closed open open closed closed 5-6 open open open open closed closed closed closed open open open open closed closed closed closed 7-8 open open open open open open open open closed closed closed closed closed closed closed closed J5: CPU frequency ratio Connectors Label Function CN1 CPU fan connector CN2 Motherboard fan connector CN3 Ethernet connector CN4 Audio connector CN5 PCI connector CN6 CD Audio input connector CN7 AUX Line in connector CN8 Main power connector CN9 Keyboard & PS/2 mouse connector CN10 Floppy drive connector CN11 PC/104 ISA-bus expansion CN12 IDE hard drive connector CN13 Reserved connector CN14 Parallel port connector CN15 Front panel connector CN16 USB connector (channel 1 & 2) CN17 IR connector CN18 CRT display connector CN19 Video out connector CN20 Flat panel connector CN21 Ext. flat panel connector CN22 Peripheral power connector CN23 COM port connector 2 PCM-5864/5864L Start Up Manual 1.5 /3.5 2* 2.5 3 4 1 2 1 2 3 4 3 4 5 6 5 6 4.5 5 1 5.5 (reserve) 2 1 2 3 4 3 4 5 6 5 6 J7: CMOS clear Closed Pins 1-2 2-3 Result Normal (3 V battery on)* Clear CMOS J8: Backlight signal select Positive signal* 1 2 3 Negative signal 1 2 3 J9: System/PCI clock setting System 50 MHz PCI 25 MHz 60 MHZ 30 MHz J18 Buzzer enable/disable *66 MHz 75 MHz *33.3 MHz 37.5 MHz 2 4 6 2 4 6 2 4 6 2 4 6 1 3 5 1 3 5 1 3 5 1 3 5 Closed pins Closed Open Result Buzzer enable* Buzzer disable J19 ~ J21: COM2 RS-232/422/485 setting *RS-232 J10: PCI/clock setting *33 MHz 1 CPU CLK/2 2 3 1 2 RS-422 RS-485 5 3 1 5 3 1 5 3 1 5 3 1 5 3 1 5 3 1 6 4 2 6 4 2 6 4 2 5 3 1 5 3 1 5 3 1 6 4 2 6 4 2 6 4 2 J19 3 J20 J11: COM4 RI pin setting +5 V +12 V *RI 6 4 2 6 4 2 6 4 2 5 3 1 5 3 1 5 3 1 J21 J22: LCD shift clock setting J12: COM3 RI pin setting +5 V +12 V Closed pins 1-2 2-3 *RI 6 4 2 6 4 2 6 4 2 5 3 1 5 3 1 5 3 1 Result shift clock* # shift clock J23: Audio power setting *+5 V (V CC) J13: CompactFlash enable/disable Pins closed open Result enable* disable +12 V (regulator) 1 1 2 2 3 3 J25: TV out format select J14: COM1 RI pin setting +5 V +12 V NTSC* PAL *RI 6 4 2 6 4 2 6 4 2 5 3 1 5 3 1 5 3 1 1 2 3 1 2 3 JP1: ATX power switch ATX power on/off toggle button J15: COM2 RI pin setting +5 v +12 V *RI JP2: Watchdog timer action 6 4 2 6 4 2 6 4 2 5 3 1 5 3 1 5 3 1 J16: LCD power setting *5 V 3.3 V 1 1 2 2 3 3 Closed Pins 1-2 2-3 *default setting Result system reset* IRQ11 Locating Jumpers PCM-5864/5864L mechanical drawing PCM-5864/L Mechanical drawing (component side) Locating Connectors PCM-5864/L Mechanical drawing (solder side) 4 PCM-5864/5864L Start Up Manual