RA-V6-2SERIES SURGE ABSORBER ●RA-V6-2 Safety Approvals : UL 497B UL The RA-V6-2 series utilizes creeping corona discharge, thus demonstrating extremely fast response characteristics in dark ambient conditions without the use of radioactive isotopes. For example, a 1.2/50μs, 10kV surge voltage can be suppressed to about 1kV. Applied as indirect lightning surge protection in telephone equipment, this model is used for parallel connection between T and R in telephone receivers. Also, by connecting this absorber within electronic circuits, network computers can be protected from destructive impulse current. File No . E139599 ●Features: 1. Fast response time. 2. This Surge Absorber is bipolar. The device will fail open if the surge withstand capability is exceeded. 3. Inter-terminal capacity is extremely small, resulting in little influence on electronic circuits. 4. High insulation resistance（1X10 9 ohms or more）. 5. Repeatable - may be used up to 300 times at 500A （8/20μs）. 6. Small size allows soldering together with resistors or other electronics components. 7. Product available taped for auto insertion. Add “Y”to model number（RA-201P-V6Y-2）. Unit : mm ELECTRICAL SPECIFICATIONS Model No. RA-201P-V6-2 RA-231P-V6-2 RA-261P-V6-2 RA-301P-V6-2 RA-311P-V6-2 RA-351P-V6-2 RA-391P-V6-2 RA-501P-V6-2 RA-201M-V6-2 RA-231M-V6-2 RA-261M-V6-2 RA-301M-V6-2 RA-311M-V6-2 RA-351M-V6-2 RA-391M-V6-2 RA-501M-V6-2 D.C. spark-over Voltage （when lighted） （V） 200±15% 230±15% 260±15% 300±15% 310±15% 350±15% 390±15% 500±15% 200±15% 230±15% 260±15% 300±15% 310±15% 350±15% 390±15% 500±15% Peak Surge Current 8/20 s （A） Capacitance （PF） Operating Temp Range （℃） 1500 2 Max. −20℃ to ＋70℃ 1500 2 Max. −20℃ to ＋70℃ Series P - No marking on part Series M - Coded marking on part 70 RA-V6-2SERIES Low Cost Series ●Taping type（RA−○○○P−V6−Y−2） Description Outside dimention Symbol Dimension Height L 14max Lamp diameter A φ5.85±0.65 Lead diameter d 0.45±0.05 Product's height from board L1 16max Lamp pitch P 12.7±1 Hole pitch P0 12.7±0.3（Note） P1 3.85±0.7 P2 6.35±1.3 F 5± 0.6 0.2 RA Hole position Pitch between leads Declining h ±2 Paper width W 18±0.5 Hole position W1 9±0.5 Lead clinch height H0 16±0.5 Product height H1 32.5max Lead length H 18.5max Hole diameter D0 φ4±0.2 t 0.7±0.2 Paper thickness Note）Accumulative pitch error : 4 pitches -50.8 ±0.6mm, 20 pitches 254±1.5mm. ●Forming type（RA−○○○P−V6−F−2） Unit : mm SURGE ABSORBERS Outside dimention Unit : mm V - T Characteristics Impulse Circuit Endurance Characteristics 71