3.3V Surface Mount 3.2mm x 5.0mm Oscillators V7323 & V7333 Series VCXO 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Description Features: The Connor-Winfield, RoHS compliant, V7323 and V7333 are hermetically sealed, Surface Mount, 3.3V Voltage Controlled Crystal Oscillators (VCXO) with Tri-State Enable/Disable function on pad 6. The V7323 and V7333 are designed for phased lock loop applications requiring low jitter and tight stability. •RoHS Compliant •3.3V Operation •Small Surface Mount Package: 5.0mm x 3.2mm x 1.2mm •Overall Frequency Tolerance: V7323: ±50ppm V7333: ±100ppm •Low Jitter <1pS RMS •Temperature Range -10° to 85°C •Enable / Disable Pad 6 •Tape and Reel Packaging Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Control Voltage (Vc) Minimum -55 -0.5 -0.5 Nominal Maximum Units 125 7.0 Vcc °C Vdc Vdc Maximum Units 52 MHz 50 100 85 3.465 ppm 15 25 mA 1 5 ps RMS Maximum Units 3.15 - 10 - - - 0.3 Vdc ppm % Ohm KHz Vdc - - - Notes Operating Specifications Parameter Minimum Nominal Frequency Range (Fo) 2.0 - Frequency Tolerance Model V7323 -50 - Model V7333 -100 - Operating Temperature Range -10 - Supply Voltage (Vcc) 3.135 3.3 Supply Current (Icc) 1.0 to 29.999 MHz - - 30 to 52 MHz - - Jitter: Integrated Phase Jitter (BW=12kHz to Fo/2 MHz) Period Jitter - - Notes 1 °C Vdc Input Characteristics Parameter Control Voltage Range (Vc) Frequency Pullability @ 25°C Monotonic Linearity Input Impedance Modulation Bandwidth (3dB) Enable Input Voltage - High (Vih) Disable Input Voltage - Low (Vil) Minimum 0.15 ±100 -10 - 10 0.7Vcc - Nominal 1.65 - - 50K - - - Notes 2 LVCMOS Output Characteristics Parameter Bulletin Page Revision Date Vx507 1 of 2 02 04 June 2015 Load Voltage High (Voh) Low (Vol) Current High (loh) Low (lol) Duty Cycle at 50% of Vcc Rise / Fall Time 20% to 80% Start-up Time Minimum - 2.97 - -1 - 40 - - Nominal - - - - - 50 - - Maximum Units 15 - 0.33 - 4 60 5 10 pf Vdc Notes mA % nS mS Notes: 1. Referenced to (Fo) measured with control voltage @ 2.5Vdc. Inclusive of frequency vs. temperature stability, supply voltage, load change, shock and vibration, 15 years aging. 2. The Output is enabled with no connection on the enable pin. Output is at high impedance when disabled. 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Package Characteristics Package Suggested Pad Layout Hermetically sealed, ceramic leadless package. .040 (1.0mm) Environmental Characteristics Temperature Cycle Hermetical Solvent Resistance The specimen shall meet electrical characteristics after tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene .040 (1.0mm) .060 (1.5mm) .043 (1.1mm) .043 (1.1mm) .040 (1.0mm) .060 (1.5mm) .043 (1.1mm) Soldering General Conditions Typical Operation Data (Vapor phase reflow) .130 (3.3mm) 260°C max x 10 sec max x 2 times max o r 230°C max x 180 sec max x 1 time 20 to 100 sec up to 215°C, 50 sec at 215°C, then down to room temperature per 1 to 5°C / sec Mechanical Characteristics Free Drop The specimen shall meet electrical characteristics after tested 3 times, Free Drop testing on the hard wooden board from a height of 75 cm. Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 245°C max x 10 sec max x 2 times, or 215°C max x 180 sec max, the specimen shall meet electrical characteristics Solderability EIAJ-RCX-0102/101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235°C ±5°C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec ±0.5 sec into solder bath Test Circuit A E/D POWER SUPPLY OSCILLOSCOPE Vcc 6 V PROBE 5 4 OSC .01uf 1 CL 2 3 FREQ COUNTER INPUT for C/V After performing the above procedures, a newly soldered coverage shall be greater than 90% Package Outline .196 (5.0mm) Pad Connection .100 .031 (2.54mm) (.8mm) #5 #4 .125 #6 #3 (3.2mm) #2 .031 (.8mm) #1 .138 .047 (3.5mm) (2.0mm) Output Waveform Pin Function 1: Control Voltage 2: Ground 3: Ground 4: Output 5: Vcc 6: Tri-State Enable/Disable TF TR "1" LEVEL 80% 50% 20% "0" LEVEL SYMMETRY Tape and Reel Dimensions PIN 1 .53 (13.5mm) 8.46 DIA (215mm DIA) .08 (2.0mm) .217 .08 (5.5mm) (2.0mm) Ordering Information .15 (3.7mm) V7323 - 50.00 MHz 9.84 DIA (250mm DIA) .157 (4.0mm) VCXO SERIES .08 (2.0mm) 3.15 (8.0mm) 3.15 (8.0mm) CENTER FREQUENCY .06 DIA (1.5mm DIA) 1.00 DIA (25mm DIA) Dimensional Tolerance: ±.02" (.508mm) ±.005" (.127mm) .217 (5.5mm) MEETS EIA-481A and EIAJ-1009B 2,000 PCS/REEL Bulletin Page .07 (1.75mm) Revision .47 (12.0mm) Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2015 The Connor-Winfield Corporation Not intended for life support applications. Vx507 2 of 2 02 04 June 2015