Rail Mount InstallationDIN Sheet SOLICON DRC Series 3 Phase & Reversing Solid State Contactors DIN Rail Mount PART NUMBER NOMENCLATURE This installation sheet includes detailed mounting and wiring instructions which apply for Crydom SOLICON DRC 3 Phase and Reversing Solid State Contactors. Be sure to visit the product series' datasheet available at the Crydom website to complement this information. If you have questions or need additional information please contact Crydom Tech Support. Please read all mounting instructions before using your SOLICON DRC Series Solid State Contactor. Operating Voltage 40: 400 VAC (3R function only) 48: 480 VAC Series DRC 3P To install on DIN rail To remove from DIN rail WIRING DIAGRAM fig. 1 Maximum recommended terminal screw torque input 12 in-lbs (1.36 Nm) & output 15 in-lbs (1.7 Nm). TABLE 1. HP Ratings at Nominal Voltage (B) 40ºC DRC3P48xx @ 480 VAC 3 HP / 2.2 KW DRC3P48xx2 @ 480 VAC 5 HP / 3.7 KW DRC3R40xx @ 400 VAC 3 HP / 2.2 KW DRC3R48xx @ 480 VAC 5 HP / 3.7 KW 60ºC 2 HP / 1.5 KW 3 HP / 2.2 KW 2 HP / 1.5 KW 3 HP / 2.2 KW 1 HP / 0.75 KW 1.5 HP / 1.1 KW 3/4 HP / 0.55 KW 1 HP / 0.75 KW L1 L2 R 2 Controlled Legs Auxiliary Contacts, (3P function only) N.O. - N.C. Blank: 3 Controlled Legs 00: Not included 2: 2 Controlled Legs 11: 1 Solid State Auxiliary Contact, Normally Open; 1 Solid State Auxiliary Contact, Normally Closed (3P function only) 20: 2 Solid State Auxiliary Contacts, Normally Open L3 T1 L1 (C,E) (D,E) 2nd Auxiliary Contact (18 - 280 VAC) WARNING! Removing product from 35 mm rail incorrectly by not using the appropriate tool could damage the latching system 80ºC 00 Control Voltage A: 230 VAC B: 120 VAC D: 24 VAC/DC Switching Mode (3P function only) Blank: Zero Voltage Turn-On R: Instantaneous Turn-On Motor Controller / AC-53 Application fig. 2 Terminal screw type. Top/Bottom view. If multiple units are installed be sure to follow derating curves Temperature 4 D Required for valid part number For options only and not required for valid part number Wire the contactor to the output side. AWG #18 (0.8 mm2) minimum, AWG #10 (5.3 mm2) x 2 (stranded/solid) maximum. 1st Auxiliary Contact (18 - 280 VAC) Wire the contactor to the input side. AWG #18 (0.8 mm2) minimum, AWG #12 (3.3 mm2) x 2 maximum. 48 Function 3P: Three Phase 3R: Reversible MOUNTING INSTRUCTIONS (A) Install the contactor on the DIN rail (as shown in fig.1). Load Current per Phase 4: 7.6 Amp FLA (x2 Controlled Legs & 3R function); 4.8 Amp FLA (x3 Controlled Legs only) L2 A3 13 T2 T3 L3 21/23 M A1 3 Overload current protection needs to be considered CONTROL INPUT (Forward) DRC3 IND. CONT. EQ. CONTROL INPUT (Backward) [DRC3R model only] INPUT STATUS XXXX 14 T1 22/24 T2 General Use / AC-51 Application A2 T1 COMMON FOR CONTROL INPUT T3 DERATING CURVES T2 T3 DRC3Pxx (3 legs controlled) Multiple units (B) Single unit Load Current (Amps) 6 T1 5 T2 T3 4 Important Considerations 3 Be sure to use input and output voltages within operating ranges. 2 1 0 0 10 20 30 40 50 60 70 80 Ambient Temperature (ºC) 8 status. 7 Load Current (Amps) 3.15 in [80 mm] Minimum LED indicates only input status. It does not represent output To achieve maximum ratings, there must be a minimum spacing of 0.8 in (22 mm) between the devices in free air and a minimum free spacing of 3.15 in (80 mm) at the top and at the bottom. (See fig. 3) DRC3Pxx-2 (2 legs controlled) & DRC3R Single unit Multiple units (B) 3.15 in [80 mm] Minimum fig. 3 Multiple units mounting for maximum ratings 6 5 General Notes (A) See compatible accessories in corresponding datasheet. 4 3 (B) To achieve maximum ratings, there must be a minimum spacing of 0.8 in (22 mm) between the devices in free air and a minimum free spacing of 3.15 in (80 mm) at the top and at the bottom. (see fig. 3) 2 1 0 0.9 in [22 mm] Minimum (C) Normally Open (13 - 14) for DRC3xxxx411 models and DRC3xxxx420 models. 0 10 20 30 40 50 60 70 80 Ambient Temperature (ºC) Do not forget to visit us at: www.crydom.com (D) Normally Open (23-24) for DRC3xxxx420 models, Normally Closed (21-22) for DRC3xxxx411 models. (E) Not available for DRC3xxxx400 models. Copyright © 2014 Custom Sensors & Technologies. Specifications subject to change without notice. Rev. 011414 Rail Mount InstallationDIN Sheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. • Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION • Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil • Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. • Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen • Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSI ONE. • Spenga tutta l'alimentazion e che fornisce questa apparecchiatu ra prima del lavorare a questa apparecchiatu ra 存在电击、 爆炸或电弧 闪烁危险 • 在操作此设 备之前请先 关闭电源。 若不遵守这些说明， 可能会导致严重的 人身伤害甚至死亡。 • Verificare tutti i collegamenti e sostituire tutte le coperture prima della rotazione sull'alimentazi one L'omissione di seguire queste istruz ioni provocherà la morte o di lesioni serie WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG • The product's side panels may be hot, allow the product to cool before touching. • Follow proper mounting instructions including torque values. • Do not allow liquids or foreign objects to enter this product. • Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher. • Respecter les consignes de montage, et notamment les couples de serrage. • Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. • Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen, bevor Sie es berühren. • Beachten Sie die Montageanweisungen, • Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein. Le non-respect de cette directive peut entraîner, Failure to follow these instructions can result in des lésions corporelles graves ou des serious injury, or equipment damage. dommages matériels. Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschäden zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD 材料损坏和高温外壳的危险性 RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO • Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo. • Respetar las instrucciones de montaje, y en particular los pares de apretado. • No dejar que penetren líquidos o cuerpos extraños en el producto. • I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. • Seguire le istruzioni di montaggio corrette. • Non far entrare liquidi o oggetti estranei in questo apparecchio. Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales. La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature. • 产品的一侧面板可能很热，在其冷却前请 不要触碰。 • 遵照正确的安装说明，包括扭矩值。 • 请勿让液体及其他异物进入本产品。 如不能正确执行这些操作说明， 极有可能造成严重人体伤害或者设备的损坏。 Rev. 011414 Do not forget to visit us at: www.crydom.com Copyright © 2014 Custom Sensors & Technologies. Specifications subject to change without notice.