AZ AZ2500 60 AMP LATCHING POWER RELAY FEATURES • • • • • • Low cost 60 Amp switching Heavy loads to 15000 VA 4 kV dielectric Epoxy sealed construction available UL, CUR file E43203 CONTACTS GENERAL DATA Arrangement SPST (1 Form A), SPST (1 Form B)Not UL Ratings Resistive load: Life Expectancy Mechanical Electrical Minimum operations 1 x 106 1 x 105 at 40 A 250 VAC Res. Max. switched power: 15000 VA Max. switched current: 60 A Max. switched voltage: 400 VAC Set and Reset Pulse Duration 50 ms minimum 60 A at 250 VAC, 6k cycles, General Use 70°C 50 A at 250 VAC, 10k cycles, General Use 70°C 40 A at 250 VAC, 100k cycles, General Use 70°C Set Time (typical) 20 ms at nominal coil voltage Reset Time (typical) 20 ms at nominal coil voltage Material Silver tin oxide Dielectric Strength 4000 Vrms coil to contact (at sea level for 1 min.) 1500 Vrms between open contacts Resistance < 50 milliohms initially (24 V, 1 A voltage drop method) Rated Load UL, CUR COIL Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Creepage Distance 8 mm Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 70°C (158°F) -40°C (-40°F) to 105°C (221°F) Vibration 0.062" DA at 10–55 Hz Power At Pickup Voltage (typical) Temperature 666 mW single coil 1.3 W dual coil Shock Operating 20 g, 11 ms, 1/2 sine (no false operation) Non-Operating 100 g, 11 ms, 1/2 sine (no damage) Max. 105°C (221°F) NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. Enclosure P.B.T. polyester Terminals Tinned copper alloy P. C. (coil), heavy tabs (power) Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Weight 33 grams 3. Specifications subject to change without notice. 4. Allow suitable slack on leads when wiring, and do not subject the terminals to excessive force. 10/22/13 AZ AZ2500 RELAY ORDERING DATA COIL SPECIFICATIONS -Standard Single Coil - Termination Style 1 ORDER NUMBER* Nominal Coil Must Operate Max. Continuous Coil Resistance Unsealed Sealed VDC VDC VDC [1] ± 10% 5 4.0 6.5 24 AZ2500P1–1AE–5D AZ2500P1–-1AE–5DE 6 4.8 7.8 35 AZ2500P1–1AE–6D AZ2500P1–-1AE–6DE 9 7.2 11.7 80 AZ2500P1–1AE–9D AZ2500P1–-1AE–9DE 12 9.6 15.6 145 AZ2500P1–1AE–12D AZ2500P1–-1AE–12DE 24 19.2 31.2 575 AZ2500P1–1AE–24D AZ2500P1–-1AE–24DE 48 38.4 62.4 2270 AZ2500P1–1AE–48D AZ2500P1–-1AE–48DE * Add suffix “K” for Coil Termination Style 2. Replace 1AE with 1BE for Form B(not UL). Add suffix R for negative polarity(not UL). COIL SPECIFICATIONS -Standard Dual Coil ORDER NUMBER* Nominal Coil Must Operate Max. Continuous Coil Resistance Unsealed Sealed VDC VDC VDC [1] ± 10% 5 4.0 6.5 12 AZ2500P2–1AE–5D AZ2500P2–-1AE–5DE 6 4.8 7.8 17.5 AZ2500P2–1AE–6D AZ2500P2–-1AE–6DE 9 7.2 11.7 40 AZ2500P2–1AE–9D AZ2500P2–-1AE–9DE 12 9.6 15.6 72 AZ2500P2–1AE–12D AZ2500P2–-1AE–12DE 24 19.2 31.2 285 AZ2500P2–1AE–24D AZ2500P2–-1AE–24DE 48 38.4 62.4 1135 AZ2500P2–1AE–48D AZ2500P2–-1AE–48DE NOTE: Relays may be ordered with twisted copper wire terminations (Styles A-K) as shown below. Contact factory for ordering information. [1] max. continuous voltage should not be applied for more than 30 seconds. * Replace 1AE with 1BE for Form B(not UL). Add suffix R for negative polarity(not UL) MECHANICAL DATA Outline Dimensions PC Board Layout (Bottom View) Wiring Diagram Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 10/22/13 AZ AZ2500 Weld style of twisted copper wire (A to K) A F C B G H K D E Notes: Weld figures for AZ2500 with twisted copper wire. Please show welding style (A to K) and the length of wires when ordering. Please note the length of each wire from left to right if the length is different. 10/22/13