EMC FILTERS - AIT Components Ltd

EMC FILTERS
Single-Phase Filters, Three-Phase Filters,
Three-Phase + Neutral Line Filters, DC Filters,
Screened Room Filters (3Ph+N) , Output Ferrites,
dV/dt Output Filters , Feedthrough Filters
PREMO EMC Filters
INTRODUCTION
Electromagnetic Interference
Most electronic equipment generates electromagnetic interference,which in some
cases may be intentional (a radiofrequency generator) or unwanted (electronic motor
speed controller). This interference is mainly propagated in two ways, one via an energy
conducting network, and the other through the air. These are called CONDUCTED
INTERFERENCE (150 KHz TO 30 MHz) and RADIATED INTERFERENCE (30 MHz to 300
MHz), respectively.
Also, electronic equipment can fail when working within an electromagnetic environment.
This tendency to fail is very common and is known as ELECTROMAGNETIC SUSCEPTIBILITY.
The relationship between perturbing and victim equipment is known as ELECTROMAGNETIC
COMPATIBILITY.
These terms are abbreviated as follows:
EMC = Electromagnetic Compatibility
EMS = Electromagnetic Susceptibility
CE = Conducted Interference (Emission)
RE = Radiated Interference (Emission)
EMI = Electromagnetic Interference
Conducted Interference
The interference conducted through an energy conduction network has two propagation
routes.
COMMON MODE. Also called ASYMMETRIC. This perturbation is present between the
safety earth and the conduction lines.
DIFFERENTIAL MODE. Also called SYMMETRIC. This perturbation is present in the
conduction lines.
Radiated Interference
This propagation through space is caused by the fact that the equipment, or some part of
it, is acting as an efficient antenna over a given frequency range. It is captured, by induction,
in the power supply cable, or even directly by some internal element of the device which acts
as an efficient receiving antenna over the same frequency range as the interfering signal.
How to minimize the interference
In order to avoid a high degree of contamination of the power supply lines with
electromagnetic interference (EMI), equipment which could cause its generation should
incorporate a power line filter, in order to block, as far as possible, the passing of this
interference. Also, as it is not possible to have a clean power supply line, the line filter also
prevents the passing of this interference to the equipment.
a) The filter has to attenuate the interference passed to the power line.
b) The filter has to attenuate the interference from the power line.
Basically, the filters should be designed as low-pass filters, to achieve a significant
attenuation in the frequency band which covers the interference, and a minimal attenuation
at the power line frequency.
Of course, the design of a filter has to take into account also that its characteristic
impedance should be as unmatched as possible to that of the interference in order that the
perturbation is reflected back to its source.
258
Filter characteristics
The filters should cover the range of frequencies between 10 KHz and 300 MHz, although
the range can be different depending on the standard to be applied. They should generate
high insertion losses within the specified frequency range.
The insertion losses should be defined for both SYMMETRIC and ASYMMETRIC modes.
As the filters are normally installed in the power supply line, they should comply with the
appropiate standards.
PREMO EMC Filters
INTRODUCTION
Special Line Filters
In this catalogue it is possible to select power line filters of one or more stages, with printed
circuit connection, spade fasterners, cables, IEC connector incorporated, screw or clip
mounting, and a wide variety of accessories such as fuses, voltage selectors, switches etc...
If you do not find the type which best suits your requirements for current attenuation, size,
mounting, etc. We can manufacture the model which suits your requirements on request.
PREMO has a laboratory equipped with the most modern and sophisticated instrumentation
to be found on the market, and its manufacturing plant uses a flexible production system
which allows it to offer made to measure solutions.
Selection and installation
The choice of the most suitable power line filter and its installation in the equipment are
of primary importance if we wish to fully benefit from its features. As can be seen later on,
we have models with and incorporated connector and direct access from the exterior, and
others for internal mounting on the chassis or the printed circuit. In all cases the external
shielding of the power line filter should be connected to the equipment chassis and the
power and load lines should be as short as possible and sufficiently separated.
Verification Tests
In the final stage of the manufacturing process, the PREMO power line filters have to pass
strict verification tests to check their reliability and safety for use. The methods followed are
described below:
1) High voltage test
Apply voltage of:
1850 VAC 50 Hz 3s between L-N/PE
1750 VDC 3s between L/N
Medical series (M) 2500 VAC between L-N/PE
2) Leakage current test
The verification is carried out according to standards using specially designed equipment.
The limits are indicated for each series. See diagram in fig. 4.
3) Attenuation test
Attenuation is defined as the relation, in dB between the power input to the load with and
without the filter over the full range of working frequencies.
See diagrams for the measurement of attenuation in common and differential modes in
fig. 5 and 6.
259
PREMO EMC Filters
INTRODUCTION
General Technical Characteristics
- Rated voltage single phase: 250 VAC 50/60 Hz
- Rated voltage three phase: 520/760 VAC 50/60 Hz
- Rated current: The rated current, INOM is given for an ambient temperature the
permissible operating current, IPERM, must be reduced according to the follwing formula:
- Dielectric strength test:
L-N / PE 1850 VAC 3s
L/N 1750 VDC 3s
- Leakage current: 250 V 50/60 Hz
0.552 x rated for 115 V 50/60 Hz
- Climatic category: HPF/HMF
- Component tolerance:
L: -30%, +50% C: -20%, +20%
R: -10%, +10%
- Types of connexion:
Z = Faston 6,30 x 0,8 mm
X = Cables UL-1015
V = Pins for P.C.B Ø = 1.3/0,8 mm
W = Screws M4 / M6 / M10
B = Terminal block
P= Bus Bar
Diagram Powerline
Figure 4
Figure 5
260
Figure 6
FA (1-30A)
FA-V (1-6A)
FB (1-20A)
FC (3-10A)
FC1 FC2 FC3 FC4
FD (1-6A)
CONSUMER
ELECTRONICS
LIFTS
INDUSTRIAL
AUTOMATION
RENEWABLE
ENERGY
TELECOMUNICATIONS
ELECTROMEDICAL
DRIVES AND
CONTROLS
PREMO EMC Filters
C-Series
DTRF (20-50A)
MILITAR
APPLICATIONS
TRANSPORT
EMC Filter Chart by Application
FDC (1-6A)
FDV (1-10A)
FE (1-30A)
FEDC (25-1500A)
FEH (1-30A)
FEHV (6-30A)
FF (3-20A)
FFH (1-16A)
FFHV (6-30A)
FG/FGR - T (3-6A)
FG/FGR - V (3-6A)
FG/FGR (3-6A)
FI (2-10A)
FI-F (2-10A)
FI-FM (2-10A)
FL (1-10A)
FOVT (8-70A)
FR/FRR (1-10A)
FT (1-6A)
FTA (3-6A)
FTC (1-6A)
FTC-C (1-6A)
FTC-M (1-6A)
FTCV (1-6A)
FTCV-C (1-6A)
FTCV-M (1-6A)
FT-M (1-6A)
FTN (1-6A)
FTN-M (1-6A)
FTO (1-6A)
FTO-M (1-6A)
FVBD (7-250A)
FVDT (7-900A)
FVDT-D (5-28A)
FVNSB (8-200)
FVRB (35-300A)
FVSB (7-180A)
FVST (6-660A)
FVTC (10-1000A)
FVTO-IV (6-180A)
HCWMF (150-2500A)
N-1 N-2 N-3
P-0999 (16-60A)
P-Series
PE (0,5-6A)
PF (50-150A)
PFT (3-150A)
STF (8-200A)
261
PREMO EMC Filters
RAPID GUIDE
Single phase Filters
CHASSIS PANEL MOUNTING
PCB MOUNTING
SCREENED
General
Medical Use For SMPS High Atten. Very High Atten. Metal Box Plastic Box ROOM FILTERS
Use
FA
FG
FC
FE
FB
FA-V (1-6 A)
PE
(14 KHz-10 GHz)
(1-30 A)
(3-6 A)
(3-10 A)
(1-30 A)
(1-20 A)
FG-V (1-6 A) (0,5-6 A)
FC1 (10-85 A)
PF
FGR
FL
FEH
FF
(150 KHz-10 GHz)
(50-150 A)
(3-6 A)
(1-10 A)
(1-30 A)
(3-20 A)
FC2 (10-85 A)
FR/FRR
FFH
(1-30 A)
(1-16 A)
SMPS = Switched Mode Power Supply
PCB = Printed Circuit Board
FEHV
FFHV
(6-30 A)
(6-30 A)
Single phase Filters
Chassis Panel Mounting with IEC Connector
General Use
Size reduced
With Fuses
Fuse + Switch
FD
(1-6 A)
FTA
(3-6 A)
FI/FI-F
(1-10 A)
FT-FTN
(1-6 A)
FTC
(1-6 A)
General Use
High Atten.
FDC
(1-6 A)
FGT
(3-6 A)
Earth Choke
Medical Use
FI-FM
(1-10 A)
FT-M/FTN-M/FTC-M
(1-10 A)
Fuse + Switch +
Voltage Selector
FTCV
(1-6 A)
FTCV
(1-6 A)
FTCV-M
(1-6 A)
3-Phase Filters
3-Phase
+ Neutral
3-Phase without neutral for frecuency inverters
One Stage
FVSB
PFT
FVST
(3-150 A) (3-110 A) (7-180 A)
STF
FVTC
(8-200 A) (10-1000 A)
Double Stage
FVTO-IV
(7-280 A)
FVNSB
(8-200 A)
Compact Size
FVDB
(7-250 A)
FVDT
(7-75 A)
FVST
FVDT
(180-660 A) (100-900 A)
DTRF
(20-50 A)
FVRB
(35-300 A)
FVDT-D
(6-28 A)
P-0999
4 kw - 16 A
11 kw - 36 A
18,5 kw - 55 A
HCWMGF
(150-2500 A)
Dc Filters
Name
FEDC series
Voltage
Current
1200 Vdc
(25-1500 A)
Feedthorught Filters
Voltage
Current
Topology
P Series
250Vac/400 Vdc
(10 - 63 A)
Single Line Pi Circuit
C Series
250Vac/400 Vdc
(10 - 250 A)
Single Line C Circuit
Name
262
Frecuency
Inverters Output
Screened Room
Filters
3-Phases + Neutral
N-1 N-2 N-3
(16-125 A)
FC3
(14 Khz - 10 Ghz)
(16-125 A)
FOVT
(8-70 A)
(dV/dT)
FC3
(150 Khz - 10 Ghz)
(16-125 A)
FA
Single - Phase Filters
Chassis Panel Mounting Single Phase Filter (1-30 A)
General Purpose
Chassis mounting single stage filter for general purpose.
Good attenuation over a wide frequency range.
Small size.
Low leakage current.
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage:
L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Electrical schematics
Product List
TYPE
FA-1V
FA-1X
I
1 Amp
L1
2 mH
CX
10 nF
CY
2,2 nF
FA-1Z
FA-3V
FA-3X
FA-3Z
FA-6V
FA-6X
FA-6Z
FA-10X
FA-10Z
FA-20W
FA-20Z
FA-30W
CONNECTION
WEIGHT
±g
1,3mm PIN
AWG18 wire
43
59
FASTON 6,3mm
1,3mm PIN
47
46
AWG18 wire
FASTON 6,3mm
61
47
0,21 mA
1,3mm PIN
AWG18 wire
48
55
0,45 mA
FASTON 6,3mm
AWG18 wire
49
130
0,45 mA
FASTON 6,3mm
M6 SCREW
124
565
0,21 mA
FASTON 6,3mm
M6 SCREW
150
646
HOUSING LCURRENT
205
204
0,21 mA
203
205
3 Amp
6 Amp
10 Amp
20 Amp
30 Amp
1,3 mH
0,8 mH
0,5 mH
0,48 mH
0,48 mH
10 nF
10 nF
100 nF
100 nF
33 nF
2,2 nF
204
203
2,2 nF
205
204
4,7 nF
203
213
4,7 nF
212
223
2,2 nF
216
223
0,21 mA
263
FB
Single - Phase Filters
High Attenuation Single Phase Filter (1-20 A)
General Purpose
Double stage filter.
High attenuation.
General purpose applications with high EMI levels.
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage:
L/N-›PE: 1800Vac 2s
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d)
Flammability class: UL 94 V2.
Electrical schematics
Product List
264
CONNECTION
WEIGHT
±g
0,45 mA
AWG18 WIRE
FASTON 6,3mm
132
126
213
212
0,45 mA
AWG18 WIRE
FASTON 6,3mm
115
109
4,7 nF
213
212
0,45 mA
AWG18 WIRE
FASTON 6,3mm
133
125
100 nF
4,7 nF
217
216
0,45 mA
AWG18 WIRE
FASTON 6,3mm
246
240
100 nF
4,7 nF
223
221
0,45 mA
M6 SGREW
FASTON 6,3mm
682
500
TYPE
I
L1
CX
CY
HOUSING LCURRENT
FB-1X
FB-1Z
1 Amp
3 mH
100 nF
4,7 nF
213
212
FB-2X
FB-2Z
2 Amp
2 mH
100 nF
4,7 nF
FB-5X
FB-5Z
5 Amp
1,5 mH
100 nF
FB-10X
FB-10Z
10 Amp
1 mH
FB-20W
FB-20Z
20 Amp
0,8 mH
FC
Single - Phase Filters
SMPS Chassis Panel Mounting Single Phase Filter (3-10 A)
For equipment using s.m.p.s.
Chassis mounting double stage filter.
High symmetrical attenuation.
Switching mode power supplies.
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage:
L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Electrical schematics
Product List
HOUSING LCURRENT CONNECTION
WEIGHT
±g
TYPE
I
L1
L2
CX
CY
FC-3X
FC-3Z
3 Amp
3 mH
0,3 mH
100 nF
4,7 nF
215
214
0,45 mA
AWG18 WIRE
FASTON 6,3mm
170
164
FC-6X
FC-6Z
6 Amp
1 mH
0,15 mH 100 nF
4,7 nF
217
216
0,45 mA
AWG18 WIRE
FASTON 6,3mm
205
199
FC-10X
FC-10Z
10 Amp 0,5 mH 0,05 mH 100 nF
4,7 nF
217
216
0,45 mA
AWG18 WIRE
FASTON 6,3mm
249
242
Insertion Loss
265
FE
Single - Phase Filters
High Attenuation Single Phase Filter (1-20 A)
General Purpose
Chassis mounting single stage filter.
General purpose.
Good attenuation in a wide frecuency range.
Low leakage current.
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage:
L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040 (-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Electrical schematics
Product List
TYPE
FE-1X
FE-1Z
FE-3X
FE-3Z
FE-6X
FE-6Z
FE-10X
FE-10Z
FE-20W
FE-20Z
FE-30W
266
I
L1
CX
CY
1 Amp
3 mH
100 nF
4,7 nF
3 Amp
2 mH
100 nF
4,7 nF
6 Amp
0,75 mH
100 nF
4,7 nF
10 Amp
1 mH
100 nF
4,7 nF
20 Amp
0,48 mH
100 nF
4,7 nF
30 Amp
0,48 mH
100 nF
4,7 nF
HOUSING LCURRENT CONNECTION
211
210
211
210
211
210
211
210
223
216
223
0,45 mA
0,45 mA
0,45 mA
0,45 mA
0,45 mA
0,45 mA
AWG18 wire
FASTON 6,3mm
AWG18 wire
FASTON 6,3mm
AWG18 wire
FASTON 6,3mm
AWG18 wire
FASTON 6,3mm
M6 SCREW
FASTON 6,3mm
M6 SCREW
WEIGHT
±g
133
119
114
108
115
109
136
130
561
429
647
FEH
Single - Phase Filters
High Attenuation Single Phase Filter (1.30A)
General Purpose
Chassis mounting single stage filter.
High attenuation for noisy circuits.
Low leakage current.
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage:
L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Electrical schematics
Product List
TYPE
FEH-1X
FEH-1Z
FEH-3X
FEH-3Z
FEH-6X
FEH-6Z
FEH-10X
FEH-10Z
FEH-16X
FEH-16Z
FEH-20Z
FEH-30W
I
L1
CX
CY
1 Amp
12 mH
150 nF
4,7 nF
3 Amp
2,5 mH
150 nF
4,7 nF
6 Amp
1 mH
150 nF
4,7 nF
10 Amp
0,80 mH
150 nF
4,7 nF
16 Amp
0,65 mH
150 nF
4,7 nF
20 Amp
30 Amp
0,60 mH
0,67 mH
150 nF
470 nF
4,7 nF
10 nF
HOUSING LCURRENT CONNECTION
209
208
209
208
209
208
209
208
211
210
214
220
0,45 mA
0,45 mA
0,45 mA
0,45 mA
0,45 mA
0,45 mA
0,45 mA
AWG18 wire
FASTON 6,3mm
AWG18 wire
FASTON 6,3mm
AWG18 wire
FASTON 6,3mm
AWG18 wire
FASTON 6,3mm
AWG18 wire
FASTON 6,3mm
FASTON 6,3mm
M6 SCREW
WEIGHT
±g
106
100
106
100
106
100
106
100
119
113
164
210
Insertion Loss
267
Single - Phase Filters
FEHV
High Attenuation Chassis Panel Mounting Single Phase
Filter for Frequency Inverters (6-30A)
Electrical schematics
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
For single phase frecuency inverters
Hipot test voltage: L/N-›PE: 1800Vac 2s.
Double stage filter.
L-›N: 1700 Vdc 2s.
Special performance for single phase frecuency Application class:HPF Acc. TO DIN
inverters.
40040 (-25ºC/+85ºC/95% RH, 30d).
Very high asymmetrical attenuation.
Flammability class: UL 94 V2.
Product List
TYPE
FEHV-6B
FEHV-6X
FEHV-6Z
FEHV-10B
FEHV-10Z
FEHV-16B
FEHV-16Z
FEHV-20B
FEHV-30B
I
L2
R (Ω)
CX
CY
6 mH
6 Amp 10 mH 25,6 µH 680 K 940 nF 47 nF
6 mH
10 Amp 6 mH 25,6 µH 680 K 940 nF 47 nF
16 Amp 4 mH 25,6 µH 470 K
2 µF 100 n F
20 Amp 3,5 mH 25,6 µH 470 K
30 Amp 2 mH 25,6 µH 220 K
2 µF
2 µF
Insertion Loss
268
L1
100 nF
100 nF
HOUSING LCURRENT CONNECTION
224
215
221
224
221
224
221
272
272
4,54 mA
4,54 mA
9,67 mA
9,67 mA
9,67 mA
4mm2
AWG18 WIRE
FASTON 6,3mm
4mm2
FASTON 6,3mm
4mm2
FASTON 6,3mm
4mm2
6mm2
WEIGHT
±g
530
425
420
600
500
650
545
710
720
FF
Single - Phase Filters
Very High Attenuation Chassis Panel Mounting Single
Phase Filter (3-20A)
Electrical schematics
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage:
L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
General Purpose
Double stage filter.
High insertion loss.
General purpose filter.
Product List
TYPE
FF-3X
FF-3Z
FF-6X
FF-6Z
FF-10Z
FF-20W
FF-20Z
I
L1
L2
CX
CY
3 Amp
2 mH
2 mH
100 nF
2,2 nF
6 Amp 0,75 mH 0,75 mH 100 nF
2,2 nF
10 Amp 0,50 mH 0,50 mH 100 nF
20 Amp 0,48 mH 0,48 mH 100 nF
2,2 nF
2,2 nF
HOUSING LCURRENT CONNECTION
215
214
215
214
216
223
221
0,21 mA
0,21 mA
0,21 mA
0,21 mA
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
FASTON 6,3mm
M6 SCREW
FASTON 6,3mm
WEIGHT
±g
170
165
172
166
223
564
429
Insertion Loss
269
Single - Phase Filters
FFH
Very High Attenuation Chassis Panel Mounting Single
Phase Filter (1-16A)
Electrical schematics
General Specifications
General Purpose
Double stage filter.
Very high attenuation
(Symmetrical and asymmetrical).
For application with high EMI levels.
Product List
TYPE
FFH-1X
FFH-1Z
FFH-3X
FFH-3Z
FFH-6X
FFH-6Z
FFH-10X
FFH-10Z
FFH-12X
FFH-12Z
FFH-16X
FFH-16Z
I
L1
CX
CY
1 Amp
22 mH
330 nF
4,7 nF
1M
3 Amp
10 mH
470 nF
4,7 nF
470K
6 Amp
7,8 mH
1 µF
4,7 nF
220K
10 Amp 4,5 mH
1 µF
4,7 nF
220K
12 Amp 3,25 mH
1 µF
4,7 nF
220K
16 Amp
1 µF
4,7 nF
220K
Insertion Loss
270
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class: HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
2 mH
R (Ω) HOUSING LCURRENT CONNECTION
215
214
217
216
219
218
219
218
219
218
223
221
0,45mA
0,45mA
0,45mA
0,45mA
0,45mA
0,45mA
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
WEIGHT
±g
170
164
205
199
260
250
260
250
260
250
510
500
FFHV
Single - Phase Filters
Very High Attenuation Chassis Panel Mounting Single
Phase Filter for Frequency Inverters (6-30A)
Electrical schematics
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz
Hipot test voltage:
L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
For single phase frequency inverters
Double stage filter.
Special high performance for single phase
frequency inverters.
Very high attenuation.
Product List
TYPE
FFHV-6Z
FFHV-10Z
FFHV-12Z
FFHV-16Z
FFHV-25B
FFHV-30B
I
L1
6 Amp
7,8 mH
10 Amp
4,5 mH
12 Amp
3,25 mH
16 Amp
2,8 mH
25 Amp
1,6 mH
30 Amp 1,6+0,8 mH
CX
CY
1 µF
1 µF
1 µF
1 µF
2,2 µF
2,2 µF
4,7 nF
4,7 nF
4,7 nF
4,7 nF
33 nF
33 nF
HOUSING LCURRENT
218
271
271
225
272
273
0,45mA
0,45mA
0,45mA
0,45mA
3,19mA
3,19mA
CONNECTION
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
4mm2
6mm2
WEIGHT
±g
380
430
635
985
1120
1300
Insertion Loss
271
FG/FGR
Single - Phase Filters
Chassis Panel Mounting Medical Use Single Phase Filter (3-6A)
Electrical schematics
General Specifications
General Purpose
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 2500Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040 (-25ºC/+85ºC/95% RH, 30d)
Flammability class: UL 94 V2.
Filter for electromedical equipment.
Small size.
FGR: With bleeder resistor.
ZT: IEC connector version.
V: PCB mounting version.
Product List
TYPE
FG-3Z
FG-3V
FG-3X
FG-3ZT
FG-6Z
FG-6V
FG-6X
FG-6ZT
FGR-3Z
FGR-3ZT
FGR-3V
FGR-3X
FGR-6Z
FGR-6ZT
FGR-6V
FGR-6X
272
I
L1
CX
3 Amp
0,8 mH
10 nF
6 Amp
0,45 mH
10 nF
3 Amp
0,8 mH
10 nF
6 Amp
0,45 mH
10 nF
HOUSING
203
205
204
241
203
205
204
241
203
241
205
204
203
241
205
204
LCURRENT
5µA
5µA
5µA
5µA
CONNECTION
WEIGHT
±g
FASTON 6,3mm
1,3 mm PIN
AWG18 WIRE
FASTON 6,3mm
FASTON 6,3mm
1,3 mm PIN
AWG18 WIRE
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
1,3 mm PIN
AWG18 WIRE
FASTON 6,3mm
FASTON 6,3mm
1,3 mm PIN
AWG18 WIRE
48
45
54
54
49
38
55
54
48
54
45
54
49
54
38
55
FL
Single - Phase Filters
Single Phase Chassis Panel SMPS Filter (1-10A)
For equipment using s.m.p.s
High attenuation for switching power supplies.
Double stage filter.
Very high asymmetrical attenuation.
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage:
L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Electrical schematics
Product List
TYPE
FL-1X
FL-1Z
FL-3X
FL-3Z
FL-3ZH
FL-4X
FL-4Z
FL-6Z
FL-10Z
I
L1
L2
CX
CY
1 Amp 22 mH 1,2 mH 0,22 µF 4,7 nF
3 Amp 16 mH 0,03 mH 0,22 µF 4,7 nF
3 Amp 16 mH 0,25 mH 0,22 µF 4,7 nF
4 Amp 8 mH 0,06 mH 1 µF
22 nF
6 Amp 4 mH
10 Amp 4 mH
0,1 mH 0,47 µF
0,1 mH 0,47 µF
22 nF
22 nF
HOUSING LCURRENT CONNECTION
213
212
213
212
216
217
216
221
221
0,45 mA
0,45 mA
0,45 mA
2,12 mA
2,12 mA
2,12 mA
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
WEIGHT
±g
129
125
129
125
131
137
131
500
500
Insertion Loss
273
FR-FRR
Single - Phase Filters
Single Phase Chassis Panel Mounting Filter (1-30A)
For equipment using s.m.p.s
Chassis mounting filter for general purpose
applications.
Single stage filter.
Low leakage current.
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage:
L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Electrical schematics
Product List
TYPE
FR-1X
FR-1Z
FR-3X
FR-3Z
FR-6X
FR-6Z
FR-10X
FR-10Z
FR-20W
FR-20Z
FR-30W
FRR-1X
FRR-1Z
FRR-3X
FRR-3Z
FRR-6X
FRR-6Z
FRR-10X
FRR-10Z
I
L1
CX
CY
1 Amp
3 mH
33 nF
2,2 nF
3 Amp
2 mH
33 nF
2,2 nF
6 Amp
0,8 mH
33 nF
2,2 nF
10 Amp
0,45 mH
33 nF
2,2 nF
20 Amp
0,45 mH
33 nF
2,2 nF
30 Amp
1 Amp
0,60 mH
3 mH
33 nF
33 nF
2,2 nF
0,47 nF
3 Amp
2 mH
33 nF
0,47 nF
6 Amp
0,8 mH
33 nF
0,47 nF
10 Amp
0,75 mH
33 nF
0,47 nF
Insertion Loss
274
HOUSING LCURRENT CONNECTION
207
206
207
206
207
206
209
208
217
216
223
207
206
207
206
207
206
209
208
0,21 mA
0,21 mA
0,21 mA
0,21 mA
0,21 mA
0,21 mA
0,45 mA
0,45 mA
0,45 mA
0,45 mA
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
M6 SCREW
FASTON 6,3mm
M6 SCREW
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
WEIGHT
±g
53
47
56
48
60
49
90
83
510
190
515
53
47
56
48
60
49
83
90
PE
Plastic Case Filter for PCB Mounting Filter (0.5-6A)
Single - Phase Filters
Electrical schematics
General Purpose
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class: HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Plastic case filter for PCB mounting.
Low cost and space saving filter.
Good attenuation for wide frequency
range.
Low leakage current < 0,25 mA.
For digital logic circuits.
Product List
TYPE
HOUSING LCURRENT CONNECTION
WEIGHT
±g
I
L1
CX
CY
PE-05V
PE-05V-E2
0,5 Amp
20 mH
10 nF
2,2 nF
201
202
0,21 mA
PIN 0,8mm
PIN 0,8mm
27
PE-1V
PE-1V-E2
1 Amp
10 mH
10 nF
2,2 nF
201
202
0,21 mA
PIN 0,8mm
PIN 0,8mm
28
PE-3V
PE-3V-E2
3 Amp
1,3 mH
10 nF
2,2 nF
201
202
0,21 mA
PIN 0,8mm
PIN 0,8mm
28
PE-6V
PE-6V-E2
6 Amp
0,8 mH
10 nF
2,2 nF
201
202
0,21 mA
PIN 0,8mm
PIN 0,8mm
27
83
Insertion Loss
275
PF
Single - Phase Filters
General Purpose Single Phase Filter (50-150A)
General Purpose
Chasis mounting single stage filter
for general purpose.
High current.
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage:
L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class:UL 94 V2.
Electrical schematics
Product List
TYPE
I
CX
CY
HOUSING LCURRENT CONNECTION
WEIGHT
±g
PF-50W
PF-100W
50 Amp 0,45 mH
100 Amp 0,31 mH
2,2 µF
2,2 µF
10 nF
10 nF
274
274
0,97mA
0,97mA
M6 SCREW
M6 SCREW
3350
3950
PF-150W
150 Amp 0,28 mH
2,2 µF
10 nF
275
0,97mA
M10 SCREW
3950
Insertion Loss
276
L1
FD/FDC/FDV
Single - Phase Filters
IEC Connector Filter (1-6A)
Electrical schematics
General Specifications
IEC connector filter
IEC connector filter. General purpose.
FD: IEC connector filter.
FDC: With earth inductor. High immunity.
FDV: With voltage protection.
Product List
TYPE
FD-1X
FD-1Z
FD-3X
FD-3Z
FD-6X
FD-6Z
FDC-1X
FDC-1Z
FDC-3X
FDC-3Z
FDC-6X
FDC-6Z
FDV-1X
FDV-1Z
FDV-3X
FDV-3Z
FDV-6X
FDV-6Z
I
L1
CX
CY
1 Amp
2 mH
10 nF
2,2 nF
3 Amp
1,3 mH
10 nF
2,2 nF
6 Amp
0,8 mH
10 nF
2,2 nF
1 Amp
2 mH
10 nF
2,2 nF
3 Amp
1,3 mH
10 nF
2,2 nF
6 Amp
0,8 mH
10 nF
2,2 nF
1 Amp
2 mH
10 nF
2,2 nF
3 Amp
1,3 mH
10 nF
2,2 nF
6 Amp
0,8 mH
10 nF
2,2 nF
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
HOUSING LCURRENT CONNECTION
242
241
242
241
242
241
244
243
244
243
244
243
244
243
244
243
244
243
0,21mA
0,21mA
0,21mA
0,21mA
0,21mA
0,21mA
0,21mA
0,21mA
0,21mA
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
WEIGHT
±g
62
50
52
51
62
55
110
100
102
92
120
110
110
100
102
92
120
110
Insertion Loss
277
FI
Single - Phase Filters
Chassis Panel with IEC Connector Fused Filter (1-6A)
Electrical schematics
IEC Connector Filter
With IEC connector and fuse.
Small size.
F: With two fuses.
FM: With two fuses for electromedical
applications.
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 1800Vac 2s.
(2500Vac for M version)
L-›N: 1700 Vdc 2s.
Application class: HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Product List
TYPE
FI-2X
FI-2Z
FI-4X
FI-4Z
FI-6X
FI-6Z
FI-2XFM
FI-2ZFM
FI-4XFM
FI-4ZFM
FI-6XFM
FI-6ZFM
I
L1
CX
CY
2 Amp
2 mH
100 nF
2,2 nF
4 Amp
1,3 mH
100 nF
2,2 nF
6 Amp
0,8 mH
100 nF
2,2 nF
2 Amp
2 mH
100 nF
-
4 Amp
1,3 mH
100 nF
-
6 Amp
0,8 mH
100 nF
-
Insertion Loss
278
HOUSING LCURRENT CONNECTION
248
247
248
247
248
247
246
245
246
245
246
245
0,21mA
0,21mA
0,21mA
5µA
5µA
5µA
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
AWG18 WIRE
FASTON 6,3mm
WEIGHT
±g
86
80
86
80
86
80
92
86
92
86
92
86
FT/FTO
Single - Phase Filters
IEC Connector Filter (1-6A)
Electrical schematics
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 1800Vac 2s.
(2500Vac for M version)
L-›N: 1700 Vdc 2s.
Application class: HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
IEC Connector Filter
With IEC connector filter, fuse and switch.
External connections by user.
Small size.
M: For electromedical applications.
Product List
TYPE
FT-1Z
FT-3Z
FT-6Z
FT-1ZM
FT-3ZM
FT-6ZM
FTO-1Z
FTO-3Z
FTO-6Z
FTO-1ZM
FTO-3ZM
FTO-6ZM
I
L1
1 Amp
3 Amp
6 Amp
1 Amp
3 Amp
6 Amp
1 Amp
3 Amp
6 Amp
1 Amp
3 Amp
6 Amp
2 mH
1,3 mH
0,8 mH
2 mH
1,3 mH
0,8 mH
2 mH
1,3 mH
0,8 mH
2 mH
1,3 mH
0,8 mH
CX
CY
10 nF
2,2 nF
10 nF
-
10 nF
2,2 nF
10 nF
-
HOUSING LCURRENT CONNECTION
252
252
252
252
252
252
253
253
253
253
253
253
0,21mA
5µA
0,21mA
5µA
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
WEIGHT
±g
67
66
66
62
61
61
85
85
85
80
80
80
279
FTA
Single - Phase Filters
Small Size IEC Filter (3-6A)
Electrical schematics
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 1800Vac 2s.
L-›N: 1700 Vdc 2s.
Application class: HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
IEC filter small size
With IEC connector filter, fuse and switch.
External connections by user.
Small size.
M: For electromedical applications
Product List
TYPE
L1
CX
CY
FTA-3Z
3 Amp
1,8 mH
100 nF
3,3 nF
254
0,45 mA
FASTON 6,3mm
64
FTA-6Z
6 Amp
0,7 mH
100 nF
3,3 nF
254
0,45 mA
FASTON 6,3mm
64
Insertion Loss
280
HOUSING LCURRENT CONNECTION
WEIGHT
±g
I
FTC
Single - Phase Filters
Chassis Panel with Fused IEC Connector + Switch High
Attenuation Filter (1-6A)
Electrical schematics
IEC connector filter
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 1800Vac 2s.
(2500Vac for M version)
L-›N: 1700 Vdc 2s.
Application class: HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Compact filter with IEC connector, fuses
and switch.
High performance single stage filter.
ZM: For electromedical applications.
ZC: With earth inductor for high immunity
level.
Insertion Loss
Product List
TYPE
FTC-1Z
FTC-2Z
FTC-4Z
FTC-6Z
FTC-1ZC
FTC-2ZC
FTC-4ZC
FTC-6ZC
FTC-1ZM
FTC-2ZM
FTC-4ZM
FTC-6ZM
I
L1
1 Amp
2 Amp
4 Amp
6 Amp
1 Amp
2 Amp
4 Amp
6 Amp
1 Amp
2 Amp
4 Amp
6 Amp
7,5 mH
2 mH
1 mH
0,45 mH
7,5 mH
2 mH
1 mH
0,45 mH
7,5 mH
2 mH
1 mH
0,45 mH
CX
CY
HOUSING
LCURRENT
220 nF
2,2 nF
249
0,21mA
220 nF
2,2 nF
249
0,21mA
220 nF
-
249
5µA
CONNECTION
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
WEIGHT
±g
250
230
220
210
265
250
235
220
240
220
210
200
281
Single - Phase Filters
FTCV
Chassis Panel with Fused IEC Connector + Switch + Voltage
Selector Filter (1-6A)
Electrical schematics
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 1800Vac 2s.
(2500Vac for M version)
L-›N: 1700 Vdc 2s.
Application class: HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
IEC connector filter
Compact filter with IEC connector,
fuses and switch.
With voltage selector.
ZM: For electromedical applications.
ZC: With earth inductor for high
immunity level.
Product List
TYPE
FTCV-1Z
FTCV-3Z
FTCV-6Z
FTCV-1ZC
FTCV-3ZC
FTCV-6ZC
FTCV-1ZM
FTCV-3ZM
FTCV-6ZM
I
L1
1 Amp
3 Amp
6 Amp
1 Amp
3 Amp
6 Amp
1 Amp
3 Amp
6 Amp
7,5 mH
2 mH
0,45 mH
7,5 mH
2 mH
0,45 mH
7,5 mH
2 mH
0,45 mH
Insertion Loss
282
CX
CY
HOUSING LCURRENT CONNECTION
220 nF
3,3 nF
251
0,32mA
220 nF
3,3 nF
251
0,32mA
220 nF
-
251
253
5µA
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
WEIGHT
±g
210
205
200
210
205
200
210
205
200
FTN
Single - Phase Filters
Chassis Panel with Fused IEC Connector + Switch Filter (1-6A)
Electrical schematics
General Specifications
Maximum operating voltage: 250Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 1800Vac 2s.
(2500Vac for M version)
L-›N: 1700 Vdc 2s.
Application class: HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
IEC connector filter
With IEC connector, fuses and switch.
General purpose filter.
M: For electromedical applications.
Product List
TYPE
FTN-1Z
FTN-3Z
FTN-6Z
FTN-1ZM
FTN-3ZM
FTN-6ZM
I
L1
1 Amp
3 Amp
6 Amp
1 Amp
3 Amp
6 Amp
2 mH
1,3 mH
0,8 mH
2 mH
1,3 mH
0,8 mH
CX
CY
HOUSING
LCURRENT
100 nF
2,2 nF
250
0,21mA
100 nF
-
250
241
5µA
CONNECTION
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
WEIGHT
±g
110
110
110
110
110
110
Insertion Loss
283
Three - Phase Filters
FVDT
Three-Phase Filters for Frequency Converters without
Neutral (6-900A)
Electrical schematics
General Specifications
Maximum operating voltage: 520Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 3000Vdc 2s.
Li-›Lj: 2250 Vdc 2s.
Application class: HMF Acc. TO DIN 40040 (-25ºC/+100ºC/95% RH, 30d)
Flammability class: UL 94 V2.
Three phase double stage
Double stage three phase filter.
High performance for frequency inverters.
High current.
High voltage versions are available
Product List
TYPE
FVDT-007B
I@50ºC
7A
L
CX/CX’/CX’’
4,91 mH 1/1,5/1,5 µF
CY/CY’
R/R’
(MΩ)
-/1,5 µF 1/0.68 M
FVDT-007X
FVDT-016B
16 A
4,4 mH 2,2/2,2/1,5 µF
-/1,5 µF 1/0.68 M
30 A 1,94 mH
2,2 µF
-/2,2 µF 1/0.68 M
42 A
1,5 mH
2,2 µF
-/2,2 µF 1/0.68 M
55A 1,08 mH
307
150 mA 15 mA
307
158 mA 16 mA
2,2 µF
0,1/2,2 µF 1/0.68 M
310
158 mA 16 mA
311
75 A 0,85 mH
4mm2
1200
4mm2 + AWG18
1200
4mm2
1700
4mm2 + AWG11
1700
10mm2
1900
10mm2 + AWG9
1900
10mm2
2000
10mm2 + AWG9
2000
16mm2
2200
16mm2 + AWG6
2200
2,2 µF
0,1/2,2 µF 1/0.68 M
310
158 mA 16 mA
25 mm2
4000
2,2 µF
0,1/2,2 µF 1/0.68 M
310
153 mA 15,4 mA
50 mm2
5800
FVDT-130BE 130 A 320µH 4,4/4,4/2,2 µF 0,1/2,2 µF 1/0.68 M
310
167 mA 15,9 mA
50 mm2
6600
160µH 4,4/4,4/2,2 µF 0,1/2,2 µF 1/0.68 M
310
167 mA 15,9 mA
50 mm2
7000
FVDT-100BE 100A
FVDT-150BE 150A
284
92 mA 8,8 mA
308
FVDT-055X
FVDT-075B
303
308
FVDT-042X
FVDT-055B
88 mA 8,8 mA
304
FVDT-030X
FVDT-042B
301
302
FVDT-016X
FVDT-030B
Max.
Max.
Ifug mA
WEIGHT
HOUSING Ifug mA
CONNECTION
520V
±g
IEC 950
50Hz
800µH
Three-Phase Filters for Frequency Converters without
Neutral (6-900A)
Insertion Loss
Three - Phase Filters
FVDT
285
Three - Phase Filters
FVDT
Three-Phase Filters for Frequency Converters without
Neutral (6-900A)
Electrical schematics
General Specifications
Maximum operating voltage: 520Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 3000Vdc 2s
Li-›Lj: 2250 Vdc 2s.
Application class:
HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d)
Flammability class: UL 94 V2.
Three phase double stage
Double stage ultra compact three
phase filter.
High performance for frequency
inverters.
Product List
Max.
Max.
R/R’
Ifug mA
CONNECTION WEIGHT
TYPE
L
CX/CX’/CX’’ CY/CY’
HOUSING Ifug mA
(MΩ)
520V
Bus Bar
±g
IEC 950
50Hz
FVDT-150WE 150 A 160 µH 4,4/4,4/2,2µF 0,1/2,2 µF 1/0.68 M
313
167 mA 15,9 mA 20X3 Ø8,5 23,5+10
7500
I@
50ºC
FVDT-180WE 180 A 160 µH 4,4/4,4/2,2µF 0,1/2,2 µF 1/0.68 M
313
167 mA 15,9 mA 20X3 Ø8,5 23,5+10
8300
FVDT-280WE 280 A 160 µH 4,4/4,4/2,2µF 0,1/2,2 µF 1/0.68 M
313
167 mA 15,9 mA 25X5 Ø10,5 18,5+15
9500
FVDT-400W
400 A 150 µH 2,2/4,4/4,4µF 0,1/2,2 µF 1/0.68 M
315
189,7 mA 18,3 mA
30X5 Ø11 25+15
14400
FVDT-660W
660 A 110 µH 2,2/4,4/4,4µF 0,1/2,2 µF 1/0.68 M
315
189,7 mA 18,3 mA 30X10 Ø11 25+15
16800
FVDT-900W
900 A 110 µH 2,2/4,4/4,4µF 0,1/2,2 µF 1/0.68 M
315
189,7 mA 18,3 mA 40X10 Ø14 30+20
20000
FVDT-150BE 150 A 160 µH 4,4/4,4/2,2 µF 0,1 / 2,2 µF 1 / 0,68 M
310
167 mA 15,9 mA
7000
Insertion Loss
286
50mm2
FVSB
Three - Phase Filters
Three-Phase Filters One Stage Filter (7-180A)
Electrical schematics
General Specifications
Maximum operating voltage: 520Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 3000Vdc 2s.
Li-Lj: 2250 Vdc 2s.
Application class: HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Three phase single stage
For industrial equipments.
Easy to install.
Compact size.
Product List
R
(MΩ)
Max.
Max.
CONNECTION WEIGHT
Ifug mA
Ifug mA
TRM.Block
±g
IEC 950 520V 50Hz
I@
50ºC
L
CX/CX’
FVSB-007B
7 Amp
3,9 mH
1 µF
470 nF 1MΩ
38 mA
3,7 mA
4mm2
450
FVSB-016B
16 Amp 900 µH
2,2 µF
470 nF 1MΩ
39 mA
3,7 mA
4mm2
650
FVSB-030B
30 Amp 700 µH 4,4/2,2 µF
470 nF 1MΩ
44 mA
4 mA
6mm2
1000
FVSB-042B
42 Amp 500 µH 4,4/2,2 µF
470 nF 1MΩ
44 mA
4 mA
10mm2
1100
FVSB-055B
55 Amp 360 µH 4,4/2,2 µF
470 nF 1MΩ
44 mA
4 mA
16mm2
1250
FVSB-075B
75 Amp 150 µH 4,4/2,2 µF
470 nF 1MΩ
44 mA
4 mA
25mm2
2000
FVSB-100B 100 Amp 170 µH 4,4/2,2 µF
470 nF 1MΩ
44 mA
4 mA
50mm2
3100
FVSB-130B 130 Amp 75 µH
4,4/2,2 µF
470 nF 1MΩ
44 mA
4 mA
50mm2
3200
FVSB-180B 180 Amp 75 µH
4,4/2,2 µF
470 nF 1MΩ
44 mA
4 mA
90mm2
4550
TYPE
CY
287
FVSB
Three - Phase Filters
Three-Phase Filters One Stage Filter (7-180A)
A
B
C
D
E
F
G
H
Insertion Loss
288
7A
190
70
40
160
180
20
4,5
M5
16A
250
70
45
220
235
25
5,4
M5
30A
270
85
60
240
255
30
5,4
M5
42A
310
85
60
280
295
30
5,4
M6
55A
310
90
60
280
295
30
5,4
M6
75A 100A 130A
270 270 270
140 150 150
85
90
90
240 240 240
255 255 255
60
65
65
6,5 6,5 6,5
M6 M10 M10
180A
380
170
120
350
365
102
6,5
M10
Three-Phase Filters For Frequency Converters without
Neutral (6-28A)
Electrical schematics
Three - Phase Filters
FVDT-D
General Specifications
Maximum operating voltage: 520Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 3000Vdc 2s
Li-›Lj: 2250 Vdc 2s.
Application class:
HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d)
Flammability class: UL 94 V2.
Three phase double stage
Double stage three phase filter.
Low leakage current.
Product List
TYPE
I@
50ºC
FVDT-005DB 5 Amp
FVDT-005DX
FVDT-008DB 8 Amp
FVDT-008DX
FVDT-016DB 16 Amp
FVDT-016DX
FVDT-028DB 28 Amp
FVDT-028DX
L
CX
CY
R/R’
10 mH
1 µF
15 nF
1 MΩ
5,8 mH 1 µF
15 nF
1 MΩ
3,7 mH 1 µF
15 nF
1 MΩ
2,9 mH 1 µF
15 nF
1 MΩ
Max.
Max.
HOUSING Ifug mA Ifug mA
IEC 950 400V 50Hz
305
3,2 mA 0,28 mA
306
305
3,2 mA 0,28 mA
306
303
3,2 mA 0,28 mA
304
303
3,2 mA 0,28 mA
304
CONNECTION
WEIGHT
±g
4mm2
700
4mm2 + AWG18 WIRE
700
4mm2
700
4mm2 + AWG18 WIRE
700
4mm2
1000
4mm2 + AWG11 WIRE 1000
6mm2
1900
6mm2 + AWG9 WIRE 1900
Insertion Loss
289
Three - Phase Filters
FVST
Three-Phase Filters For Frequency Converters without
Neutral (6-660A)
Electrical schematics
General Specifications
Maximum operating voltage: 520Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 3000Vdc 2s.
Li-Lj: 2250 Vdc 2s.
Application class: HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Three phase one stage
Single stage three phase filter.
For fast switching applications.
High current.
Some high voltaje version are available.
Product List
TYPE
FVST-006
FVST-008
FVST-016
FVST-025
FVST-036
FVST-050
FVST-064
FVST-080
FVST-110
FVST-180
FVST-250
FVST-350
FVST-450
FVST-660
I@
50ºC
L
CX/CX’
CY/CY’
R/R’
(MΩ)
6 Amp
8 Amp
16 Amp
25 Amp
36 Amp
50 Amp
64 Amp
80 Amp
110 Amp
180 Amp
250 Amp
350 Amp
450 Amp
660 Amp
7 mH
5,5 mH
4 mH
2,9 mH
2,2 mH
1 mH
0,55 mH
1 mH
0,7 mH
0,4 mH
0,13 mH
0,13 mH
0,15 mH
0,14 mH
1/- µF
1/- µF
2,2/- µF
4,4µF
4,4µF
4,4µF
4,4µF
6,6µF
6,6µF
6,6µF
11µF
11/22 µF
11/22 µF
11/22 µF
/-/470/- nF
/-/470/- nF
/-/470/- nF
10nF/47nF/1µF
10nF/47nF/1µF
10nF/100nF/1µF
10nF/100nF/1µF
47nF/100nF/1µF
47nF/100nF/1µF
47nF/100nF/1µF
100nF/100nF/1µF
100nF/100nF/1µF
100nF/100nF/1µF
100nF/100nF/1µF
470/10MΩ
470/10MΩ
1M/10MΩ
1MΩ
1MΩ
1MΩ
1MΩ
1MΩ
1MΩ
1MΩ
1MW/470KΩ
1MW/470KΩ
1MW/220KΩ
1MW/470KΩ
Insertion Loss
290
Max.
Max.
HOUSING Ifug mA Ifug mA
IEC 950 400V 50Hz
301
38 mA
3,7 mA
303
39 mA
3,7 mA
303
44 mA
4 mA
309
190 mA 17,6 mA
309
190 mA 17,6 mA
309
190 mA 17,6 mA
309
190 mA 17,6 mA
310
226 mA 18,7 mA
310
226 mA 18,7 mA
312
226 mA 18,7 mA
315
255 mA 19,4 mA
315
262 mA 19,6 mA
315
262 mA 19,6 mA
315
262 mA 19,6 mA
CONNECTION
Hx0 Ø M+N
WEIGHT
±g
4mm2
4mm2
4mm2
6mm2
10mm2
10mm2
25mm2
25mm2
50mm2
M10 SCREW
25X5 Ø11 25+15*
25X5 Ø11 25+15*
30X5 Ø11 25+15*
30X10 Ø11 25+15*
700
1600
1600
2400
2400
2400
2400
4500
4500
-
HCWMGF
Three-Phase Filters For Wind Mills Applications (150-2500A)
Three - Phase Filters
General Specifications
- Maximum operating voltage: 720 Vac
- Operating frequency: DC – 60Hz
- Hipot test voltage:
L/N-›·PE: 3100 Vdc 2s
Li-Lj: 3000 Vdc 2s
- Flammability class: UL 94 V2
Three Phase Filters
High-Power filters for rated currents up to 2500A
Attenuation loss for Class A compliance.
Protective cover for busbar optional
High voltage for IT networks
HCWMGFR-XXXXHV-LL Low Leakage Current version
Applications
High power inverters, converters,
UPS and renewable
energy equipments
Electrical schematic
Product List
TYPE
Leakage Power
Rated Current Power
Current Losses
(A) @ 50 ºc (kW)
(mA)
(W)
Busbar
Connections
Weight
Housing
Connections
Input/Output
(Kg)
(mm)
HCWMGF-150HV
150
110
<6
24
M10 Screw
6,5
65
HCWMGF-180HV
180
132
<6
34
M10 Screw
6,5
65
HCWMGF-250HV
250
200
<6
49
M10 Screw
7
66
HCWMGF-320HV
320
250
<6
19
6 x 25
10,5
67
HCWMGF-400HV
400
315
<6
29
6 x 25
10,5
67
HCWMGF-600HV
600
500
<6
44
8 x 25
11
68
HCWMGF-800HV
800
630
<6
39
8 x 40
18
69
HCWMGF-1000HV
1000
710
<6
60
8 x 40
18
69
HCWMGF-1300HV
1300
1000
<6
100
10 x 60
27
70
HCWMGF-1600HV
1600
1320
<6
131
10 x 60
27
70
HCWMGF-2500HV
2500
2000
<6
300
15 x 70
55
71
25 x 6mm,
ǩ 10.5
25 x 6mm,
ǩ 10.5
25 x 8mm,
ǩ 10.5
40 x 8mm,
ǩ 14
40 x 8mm,
ǩ 14
60 x 10mm,
ǩ 14
60 x 10mm,
ǩ 14
70 x 15mm,
ǩ 14
291
HCWMGF
Three - Phase Filters
Three-Phase Filters For Wind Mills Applications (150-2500A)
150-180A
800-1000-1300A
292
250-600A
1600-2500A
DTRF
Three - Phase Filters
Three Phase Filter for Industrial Applications (20-50A)
General Specifications
Maximum operating voltage: 520Vac
Operating frequency: DC – 60Hz
Hipot test voltage:
L/N-›PE: 2000 Vac 2s
Li-Lj: 2250 Vdc 2s
Application class: HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d)
Flammability class: UL 94 V2
Applications
Servo drives
Three phase power supplies
Medical equipment
Features
DIN guide optional for rail mounted
equipment
(DIN ended reference)
LL models for very low leakage current
NL models for better attenuation.
Electrical schematics
Product List
Rated Current
(A) @ 50 ºc
Leakage
Current
(mA)
Power
Losses
(W)
DTRF-020LL
20
<0,4
5,4
DTRF-030LL
30
<0,4
6,2
DTRF-050LL
50
<0,4
9,4
DTRF-020NL
20
<2,5
5,4
DTRF-030NL
30
<2,5
6,2
DTRF-050NL
50
<2,5
9,4
TYPE
Connections
Terminal block
4-6 mm2 / AWG 12-10
Terminal block
8-10 mm2 / AWG 8-7
Terminal block
16-20 mm2 / AWG 5-4
Terminal block
4-6 mm2 / AWG 12-10
Terminal block
8-10 mm2 / AWG 8-7
Terminal block
16-20 mm2 / AWG 5-4
Weight
(Kg)
Housing
0,56
61,63 DIN
0,58
61,63 DIN
0,98
62,64 DIN
0,56
61,63 DIN
0,58
61,63 DIN
0,98
62,64 DIN
293
DTRF
Three - Phase Filters
Three Phase Filter for Industrial Applications (20-50A)
294
20A LL
20A NL
30/50A LL
30/50A NL
FVTC
Three - Phase Filters
Three Phase One Stage Filter for Industrial Applications
(10-1000A)
General Specifications
Maximum operating voltage: 520 Vac
Operating frequency: DC – 60Hz
Hipot test voltage:
L/N-›PE: 3000 Vdc 2s
Li-Lj: 2250 Vdc 2s
Application class: HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d)
Flammability class: UL 94 V2
Electrical schematic
Three Phase One stage
For industrial motor drive applications
Protective covers as optional accessory
Compact size
Product List
TYPE
Typical drive
Rated Current
Leakage Current
Power rating
(A) @ 50 ºc
400VAC/50Hz (mA)
(KW)
Power
Losses
(W)
FVTC-010B
10
5.5
26.4
2.4
FVTC-020B
20
11
26.4
4.1
FVTC-035B
35
22
29.4
6.8
FVTC-050B
50
30
29.4
12.8
FVTC-065B
65
37
29.4
13.5
FVTC-080B
80
45
29.4
13.5
FVTC-100B
100
55
29.4
17.1
FVTC-150P
150
75
59.5
7.5
FVTC-200P
200
110
59.5
13.2
FVTC-250P
250
132
59.5
20.6
FVTC-320P
320
160
59.5
12.2
FVTC-400P
400
220
59.5
19.2
FVTC-600P
600
315
59.5
35.6
FVTC-800P
800
400
59.5
51.8
FVTC-1000P
1000
560
59.5
81
Connections
Terminal block
6 mm2 / AWG 8
Terminal block
10 mm2 / AWG 6
Terminal block
16 mm2 / AWG 4
Terminal block
25 mm2 / AWG 2
Terminal block
25 mm2 / AWG 2
Terminal block
50mm2 / AWG 0
Terminal block
95 mm2 / AWG 000
Bus Bar
20x3,ø9
Bus Bar
20x3,ø9
Bus Bar
20x3,ø9
Bus Bar
25x6,ø11
Bus Bar
25x6,ø11
Bus Bar
25x6,ø11
Bus Bar
40x8,ø13.5
Bus Bar
40x8,ø13.5
Weight
(Kg)
0.5
0.6
0.8
1.3
1.5
2.5
3
7
7
7
7.5
7.5
8
18
18
295
Three - Phase Filters
FVTC
Three Phase One Stage Filter for Industrial Applications
(10-1000A)
10 A 20 A 35 A 50 A 65 A 80 A 100 A 150 A 200 A 250 A 320 A 400 A 600 A 800 A 1000 A
A
B
C
D
E
F
G
H
V
W
X
Y
Z
296
150 150 160 170 170 200 230 300
58
58
68
80
80
90
90
86
58
58
70
85
85
95
95
200
120 120 130 140 140 170 200 240
132.5 132.5 142.5 152.5 152.5 182.5 212.5 275
42
42
50
65
65
75
75
165
4.5
4.5
5.5
5.5
5.5
5.5
5.5 Ø11
M4
M4
M6
M6
M6
M8
M8 M10
20
3
10
37
Ø9
300
86
200
240
275
165
Ø11
M10
20
3
10
37
Ø9
300
86
200
240
275
165
Ø11
M10
20
3
10
37
Ø9
300
95
200
240
275
165
Ø11
M10
25
6
12,5
37
Ø11
300
95
200
240
275
165
Ø11
M10
25
6
12,5
37
Ø11
300 370
370
95
125
125
200 190
190
240 310
310
275 345
345
165 155
155
Ø11 Ø11 Ø11
M10 M12 M12
25
40
40
8
8
8
12,5
20
20
37
47
47
Ø11 Ø13.5 Ø13.5
Three Phase One Stage Filter for Industrial Applications
(10-1000A)
10 & 20A
35 65A
80 & 100A
150 1000A
Three - Phase Filters
FVTC
297
Three - Phase Filters
FVRB
Three Phase One Stage Filter for Regenerative Converters
(35-300A)
General Specifications
Maximum operating voltage: 520 Vac
Operating frequency: DC – 60Hz
Hipot test voltage:
L/N-›PE: 3000 Vdc 2s
Li-Lj: 2250 Vdc 2s
Application class: HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d)
Flammability class: UL 94 V2
Three Phase One stage
For Regeneration units
Good saturation resistance
Book style with compact size and easy to install.
Electrical schematic
Product List
TYPE
298
Typical drive
Leakage Current
Rated Current
Power rating
400VAC/50Hz (mA)
(A) @ 50 ºc
(KW)
Power
Losses
(W)
FVRB-035B
35
22
48.9
11.8
FVRB-050B
50
30
66.1
18
FVRB-080B
80
45
71.5
25.9
FVRB-110B
110
55
71.5
32.7
FVRB-150B
150
75
71.5
50.6
FVRB-200B
200
110
71.5
67.2
FVRB-230B
230
132
71.5
36.5
FVRB-300P
300
160
71.5
54.0
Connections
Terminal block
10 mm2 / AWG 6
Terminal block
16 mm2 / AWG 4
Terminal block
25 mm2 / AWG 2
Terminal block
50 mm2 / AWG 0
Terminal block
95 mm2 / AWG 000
Terminal block
95 mm2 / AWG 000
Terminal block
95 mm2 / AWG 000
Bus Bar
150 mm2 / AWG0000
Weight
(Kg)
2.5
3.5
5.5
6
9
9.5
10
12
Three Phase One Stage Filter for Regenerative Converters
(35-300A)
A
B
C
D
E
F
G
H
35 A
50 A
80 A
110 A
150 A
200 A
230 A
300 A
335
150
60
305
320
35
6.5
M5
329
185
80
300
314
55
6.5
M6
379
220
90
350
364
65
6.5
M10
379
220
90
350
364
65
6.5
M10
438
240
110
400
413
80
6.5
M10
438
240
110
400
413
80
6.5
M10
438
240
110
400
413
80
6.5
M10
440
200
200
400
420
160
6.5
M12
BUS BAR
25x5 mm
Three - Phase Filters
FVRB
299
Three - Phase Filters
FVRB
300
Three Phase One Stage Filter for Regenerative Converters
(35-300A)
Three Phase Double Stage Filter for Industrial Applications
(7-250A)
General Specifications
Maximum operating voltage: 520 / 720 Vac
Operating frequency: DC – 60Hz
Hipot test voltage:
L/N-›PE: 3000 Vdc 2s
Li-Lj: 2250 Vdc 2s
Application class: HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d)
Flammability class: UL 94 V2
Three - Phase Filters
FVDB
Three Phase One stage
For three phase inverters and power drive system
Book style with compact size and easy to install.
High Voltage version is available
Electrical schematic
Product List
Rated Current
(A) @ 50 ºc
Typical drive
Power rating
Nor./HV(KW)
Leakage Current
440VAC/50Hz
(mA)
Power
Losses
(W)
7
4 / 5.5
16.5
9
16
7.5 / 11
18.3
20
30
15 / 22
24.2
21
42
22 / 30
25.8
30
55
30 / 45
25.8
30
75
37 / 55
25.8
24
100
55 / 90
25.8
51
130
75 / 100
30
50
FVDB-180B
180
90
30
73
FVDB-250B
250
132
30
79
TYPE
FVDB-007B
FVDB-007BHV
FVDB-016B
FVDB-016BHV
FVDB-030B
FVDB-030BHV
FVDB-042B
FVDB-042BHV
FVDB-055B
FVDB-055BHV
FVDB-075B
FVDB-075BHV
FVDB-100B
FVDB-100BHV
FVDB-130B
FVDB-130BHV
Connections
Terminal block
4 mm2 / AWG 10
Terminal block
4 mm2 / AWG 10
Terminal block
10 mm2 / AWG 6
Terminal block
16 mm2 / AWG 4
Terminal block
25 mm2 / AWG 2
Terminal block
25mm2 / AWG 2
Terminal block
50 mm2 / AWG 0
Terminal block
95 mm2 / AWG 000
Terminal block
95 mm2 / AWG 000
Terminal block
95 mm2 / AWG 000
Weight
(Kg)
1
1.5
2
2.5
3
4
5.5
7
11
12
301
Three - Phase Filters
FVDB
Three Phase Double Stage Filter for Industrial Applications
(7-250A)
A
B
C
D
E
F
G
H
302
7A
16 A
30 A
42 A
55 A
75 A
100 A
130 A
180 A
250 A
255
126
50
225
240
25
6.5
M5
305
142
55
275
290
30
6.5
M5
335
150
60
305
320
35
6.5
M6
329
185
70
300
314
45
6.5
M6
329
185
80
300
314
55
6.5
M6
329
220
80
300
314
55
6.5
M6
379
220
90
350
364
65
6.5
M10
439
240
110
400
414
80
6.5
M10
438
240
110
400
413
80
6.5
M10
478
240
110
440
453
80
6.5
M10
Three Phase Double Stage Filter for Industrial Applications
(7-250A)
Three - Phase Filters
FVDB
303
FOR FREQUENCY INVERTERS
Three - Phase Filters
Introduction
Features
Three phase filter for frequency inverters/PDS.
“Foot-print” mounting.
High attenuation properties.
Small and ergonomic size.
Maximum operating voltage: 520Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 3000Vdc 2s.
L-›N: 2250 Vdc 2s.
Application class:
HPF Acc. TO DIN 40040 (-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Introduction to Inverter Filters
PREMO has developed a very comprehensive INVERTER EMC FILTER family including two
specific sub families:
t'PPU1SJOUåMUFSTGPSJOTUBMMBUJPOCFMPXUIF*OWFSUFSBOE
t'JMUFSTGPS-*'541
Each family is designed to meet the specific ElectroMagnetic Compatibility Standard for
each product.
PREMO has the expertise and equipment to design customer specific EMC Filters; both in
Electrical and Mechanical design.
In this Filter family, Premo Manufacture EMC Filters both Single-Phase and Three-Phase up
to 900 Amps and voltages of 250V, 520V and 720V.
Inverter Connection Information
A.
B.
C.
D.
E.
F.
G.
H.
I.
304
Ground all metallic conductive parts using suitable cables to a central point. Ensure
that paint is removed from metalwork to provide a good earth contact.
The EMC Filter should be placed as close as possible to the inverter case.
Separate the motor cables and supply cables as much as possible.
Use shielded cable (with copper braid and earth wire) from the filter to the motor.
Connect the shielding and earth at the both ends.
If required, use Output Ferrites in the motor cable – place the ferrites as close to
the inverter as possible. Wind the motor cables around the ferrite (as least twice)
but do not wind the shield or earth wires around the ferrite.
Follow the Inverter Manufacturers Installation instructions, making sure that
earth is as good as possible.
Separate the motor and control cables as much as posible.
Use copper braid to connect the Electrical Control Panel with its Door, to provide
a good earth connection.
Connect the motor frame direct to earth.
FOR FREQUENCY INVERTERS
Three - Phase Filters
Introduction
305
P-0999
Three - Phase Filters
Three-Phase Filters for Frequency Converters (36-60A)
Three phase filters specially designed for
frequency inverters.
General Specifications
Maximum operating voltage: 520Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage:
L/N-›PE: 3000Vdc 2s.
Li-Lj: 2250 Vdc 2s.
Application class: HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Electrical schematics
Product List
Type
I
CX/CX’
CY/CY’
R/R’
Housing
Max. Ileak mA Max. Ileak mA
Weight
Connection
IEC 950
520V 50Hz
±g
X -0999-005
36 Amp 2,5 mH 2,2/- µF 100/330 nF
1 MΩ
309
40 mA
3,6 mA
10mm2
2400
X -0999-006
55 Amp 1,8 mH 2,2/- µF 100/470 nF
1 MΩ
310
54,8 mA
5 mA
16mm2
5700
X -0999-007
16 Amp 4,4 mH 1/-2,2 µF 100/330 nF
1 MΩ
309
40,7 mA
3,7 mA
4mm2
1900
X -0999-014
60 Amp 710µH 2,2/- µF 100/2,2µF 1000/680 KΩ
310
158 mA
15,9 mA
25mm2
7000
Insertion Loss
306
L
FEDC
DC Filters
EMC DC Filter for PV applications
Electrical schematic
General Specifications
Maximum operating voltage: 1200 Vdc max.
Operating frequency: DC.
Hi-pot test voltage: L/N-›PE: 3600Vdc 2s.
Li-Lj: 3000 Vdc 2s.
Application class: HMF Acc.TO DIN 40040
(-40ºC/+100ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Single stage
For PV (Photovoltaic) Inverters.
For Other DC applications.
According to UL1283 and EN 60939.
* FEDC- xxxxx -LL – Without Cy Capacitors.
Product List
TYPE
FEDC-25B
FEDC-25B-LL
FEDC-50B
FEDC-50B-LL
FEDC-75B
FEDC-75B-LL
FEDC-100B
FEDC-100B-LL
FEDC-150B
FEDC-150B-LL
FEDC-250P
FEDC-250P-LL
FEDC-400P
FEDC-400P-LL
FEDC-600P
FEDC-600P-LL
FEDC-800P
FEDC-800P-LL
FEDC-1000P
FEDC-1000P-LL
FEDC-1500P
FEDC-1500P-LL
Rated Current
(A) @ 50 ºc
Typical inverter AC
Power rating (KW)
Power Losses
(W) @ 25°C
25
10
8
50
20
17
75
30
18
100
40
22
150
60
31
250
100
10
400
150
16
600
250
29
800
350
26
1000
400
40
1500
500
45
Connection
Terminal block
6 mm2 / AWG 8
Terminal block
16 mm2 / AWG 4
Terminal block
25 mm2 / AWG 2
Terminal block
50 mm2 / AWG 0
Terminal block
95 mm2 / AWG 00
Bus Bar
20x5,Ø9
Bus Bar
25x6,Ø11
Bus Bar
25x8,Ø11
Bus Bar
40x8,Ø14
Bus Bar
40x8,Ø14
Bus Bar
60x10,Ø14
Weight
(Kg)
1.0
1.7
1.8
2.8
5.0
5.2
6.3
6.6
9.5
9.6
15.0
307
FEDC
DC Filters
EMC DC Filter for PV applications
308
Mechanical Dimensions (mm)
FEDC
Mechanical Dimensions (mm)
A
B
C
D
E1
E2
F1
F2
G
H
J
S
T
U
V
W
X
Y
Z
25 A
50 A
75 A
100 A
150 A
250 A
400 A
600 A
800 A
1000 A 1500 A
170
80
65
140
152,5
200
95
80
170
182,5
200
95
80
170
182,5
220
125
95
190
202,5
250
140
115
220
202,5
45
60
5,5
1
M5
60
75
5,5
1,5
M6
60
75
5,5
1,5
M6
80
100
5,5
1,5
M8
100
120
5,5
2
M10
300
180
110
130
130
110
155
300
190
110
140
130
110
165
300
190
110
140
130
110
165
300
200
140
150
130
110
175
300
200
140
150
130
110
175
300
200
150
150
130
110
175
Ø12
2
M10
Ø12
2
M10
Ø12
2
M10
Ø12
3
M12
Ø12
3
M12
70
20
5
15
58
Ø9
70
25
6
15
58
Ø11
70
25
8
15
58
Ø11
70
40
8
20
65
Ø14
70
40
8
20
65
Ø14
Ø12
3
M12
43
26
70
60
10
17
100
Ø14
DC Filters
EMC DC Filter for PV applications
Insertion Loss
309
FVTO-IV
Three Phase + Neutral Line Filters
Three-Phase Filters for Frequency Converters without
Neutral (7-180A)
Electrical schematic
General Specifications
Maximum operating voltage: 520Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 3000Vdc 2s.
L-›N: 1300 Vdc 2s.
Li-›Lj: 2250 Vdc 2s.
Application class: HPF Acc. TO DIN 40040
(-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Three Phase + Neutral Filters, Double Stage
Three phase + neutral filter for frecuency inverters/PDS.
“Foot-print” mounting.
High attenuation properties.
Small and ergonomic size.
Product List
Type
FVTO6IV
FVTO10IV
FVTO12IV
FVTO20IV
FVTO20IVB
FVTO30IV
FVTO40IV
FVTO60IV
FVTO60IVB
FVTO80IV
FVTO80IVB
FVTO100IV
FVTO150IV
FVTO180IV
310
I
6 Amp
10 Amp
12 Amp
20 Amp
20 Amp
30 Amp
40 Amp
60 Amp
63 Amp
80 Amp
80 Amp
100 Amp
150 Amp
180 Amp
L
CX/CX’/CX’’
CY/CY’
R/R’
5 mH
1 µF
47nF/470nF /-/680KΩ/680K Ω/1MΩ
5 mH
1 µF
47nF/470nF
680KΩ/680KΩ/-/5 mH
2,2µF
47nF/470nF /-/680KΩ/680KΩ/1MΩ
2 mH
2,2µF
47nF/1µF
680KΩ/680KΩ/-/2 mH
2,2µF
47nF/1µF
680KΩ/680KΩ/-/1,2 mH
2,2µF
150nF/220nF
680KΩ/-/-/1,2 mH
2,2µF
150nF/220nF
680KΩ/-/-/1,5 mH
2,2µF
330nF/2,2µF
680KΩ/-/-/330KΩ
1,5 mH
2,2µF
330nF/2,2µF
680KΩ/-/-/330KΩ
170 µH
2,2µF
150nF/220nF
680KΩ/-/-/170 µH
2,2µF
150nF/220nF
680KΩ/-/-/170 µH
2,2µF
150nF/220nF
680KΩ/-/-/160 µH 4,4/4,4/2,2µF 470nF/470nF
/-/-/1MΩ/330KΩ
160 µH 4,4/4,4/2,2µF 100nF/2,2µF
/-/-/1MΩ/680KΩ
Max.
Max.
CONNECTION
HOUSING Ifug mA Ifug mA
Hx0 Ø M+N
IEC 950 400V 50Hz
406
405
406
409
407
408
408
408
411
413
310
413
413
413
47,6 mA
47,6 mA
51,8 mA
97,6 mA
97,6 mA
37,8 mA
37,8 mA
187 mA
187 mA
16 mA
16 mA
16 mA
38,9 mA
190 mA
4,5 mA
4,5 mA
4,7 mA
9,28 mA
9,28mA
3,4 mA
3,4 mA
19,4 mA
19,4 mA
1,4 mA
1,4 mA
1,4 mA
3,4 mA
18,4 mA
6mm2
M4 SCREW
6mm2
M6 SCREW
4mm2
10mm2
10mm2
10mm2
25mm2
M10 SCREW
25mm2
M10 SCREW
M10 SCREW
M10 SCREW
Three-Phase Filters for Frequency Converters without
Neutral (7-180A)
Insertion Loss
Three Phase + Neutral Line Filters
FVTO-IV
311
PFT
Three Phase + Neutral Line Filters
Three-Phase + Neutral Filters for General Use (3-150A)
Electrical schematics
General Specifications
Maximum operating voltage: 520Vac.
Operating frequency: DC - 60Hz.
Hipot test voltage: L/N-›PE: 3000Vdc 2s.
L-›N: 1300 Vdc 2s
Li-›Lj: 2250 Vdc 2s.
Application class: HPF Acc. TO DIN
40040 (-25ºC/+85ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Three phase + Neutral filters
Single stage three phase + neutral filter.
For switching applications.
Product List
Type
I@40ºC
PFT-3Z
3 Amp
PFT-6Z
6 Amp
PFT-10Z
10 Amp
PFT-20Z
20 Amp
PFT-20W
PFT-25B
25 Amp
PFT-25W
PFT-36B
36 Amp
PFT-36W
PFT-50B
50 Amp
PFT-50W
PFT-65B
65 Amp
PFT-65W
PFT-80B
80 Amp
PFT-80W
PFT-110B 110 Amp
PFT-110W
PFT-150B 150 Amp
PFT-150W
312
L1
CX/CX’
CY
R
1 mH
0,45 mH
0,2 mH
0,2 mH
0,2 mH
1,3 mH
0,1 µF
0,1 µF
0,1 µF
0,1 µF
0,1 µF
2,2 µF
20 nF
-4,7 nF
-4,7 nF
-22 nF
-22 nF
15 nF 110 KΩ
1 mH
2,2 µF
15 nF 110 KΩ
0,55 mH 2,2µF/100 nF 15 nF
1MΩ
0,36 mH
2,2 µF
1MΩ
0,5 mH
1 µF
0,25 mH
1 µF
0,25 mH
2,2 µF
22 nF
22 nF 470kΩ
470kΩ
22 nF
470kΩ
22 nF
110KΩ
Max.
Max.
WEIGHT
HOUSING Ifug mA Ifug mA CONNECTION
±g
IEC 950 400V 50Hz
401
401
401
401
402
403
404
403
404
403
404
403
404
410
412
410
412
410
412
485 µA
485 µA
485 µA
1,9 mA
1,9 mA
3,2 mA
43 µA
43 µA
43 µA
191 µA
191 µA
280 µA
3,2 mA
280 µA
3,2 mA
280 µA
4,7 mA
412 µA
4,7 mA
410 µA
4,7 mA
410 µA
4,7 mA
412 µA
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
FASTON 6,3mm
M6 SCREW
4mm2
M6 SCREW
6mm2
M6 SCREW
10mm2
M6 SCREW
10mm2
M6 SCREW
25mm2
M10 SCREW
50mm2
M10 SCREW
50mm2
M10 SCREW
220
220
240
240
550
1500
1500
1700
1700
3000
3200
3500
PFT
Insertion Loss
Three Phase + Neutral Line Filters
Three-Phase + Neutral Filters for General Use (3-150A)
313
Three Phase + Neutral Line Filters
STF
Three-Phase + Neutral Filters for Solar Technology
Applications (8-200A)
General Specifications
Maximum operating voltage: 520 Vac
Operating frequency: DC – 60Hz
Hipot test voltage: L/N-›PE: 3000 Vdc 2s
Li-Lj: 2250 Vdc 2s
Application class: HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d)
Flammability class: UL 94 V2
Three Phase + Neutral Filters
Single stage
Solar technology applications
Compact model for saving space
Low leakage current
Electrical schematic
Product List
Type
314
Power
Rated Current Leakage Current
Losses
(A) @ 50 ºc
(mA)
(W)
STF-008HV
8
<1
2,7
STF-016HV
16
<1
6
STF-025HV
25
<1
11,6
STF-036HV
36
<1
14,8
STF-064HV
64
<1
18,4
STF-080HV
80
<1
18,9
STF-120HV
120
<1
28,5
STF-160HV
160
<1
30,7
STF-200HV
200
<1
46,8
Connection
Terminal block
4 mm2 / AWG 10
Terminal block
4 mm2 / AWG 10
Terminal block
10 mm2 / AWG 6
Terminal block
10 mm2 / AWG 6
Terminal block
25 mm2 / AWG 2
Terminal block
50 mm2 / AWG 0
Terminal block
50 mm2 / AWG 0
Terminal block
95 mm2 / AWG 000
Terminal block
95 mm2 / AWG 000
Weight
(Kg)
Housing
0,8
50
0,8
50
1,3
51
1,6
51
2,7
52
4,1
53
5,9
54
7,9
55
8,5
55
Three-Phase + Neutral Filters for Solar Technology
Applications (8-200A)
Insertion Loss
Three Phase + Neutral Line Filters
STF
315
Three Phase + Neutral Line Filters
FVNSB
Three-Phase + Neutral Filters for Industrial Applications
(8-200A)
General Specifications
Maximum operating voltage: 520 Vac
Operating frequency: DC – 60Hz
Hipot test voltage: L/N-›PE: 2750 Vdc 2s
Li-Lj: 2250 Vdc 2s
Application class: HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d)
Flammability class: UL 94 V2
Three Phase One stage
For Industrial machinery units
Compact size with Neutral Line
Electrical schematic
Product List
Rated Current
(A) @ 50 ºc
Leakage Current
(mA)
Power
Losses
(W)
FVNSB-008B
8
<1
2,7
FVNSB-016B
16
<1
6
FVNSB-025B
25
<1
11,6
FVNSB-036B
36
<1
14,8
FVNSB-064B
64
<1
18,4
FVNSB-080B
80
<1
18,9
FVNSB-120B
120
<1
28,5
FVNSB-160B
160
<1
30,7
FVNSB-200B
200
<1
46,8
Type
316
Connection
Terminal block
4 mm2 / AWG 10
Terminal block
4 mm2 / AWG 10
Terminal block
10 mm2 / AWG 6
Terminal block
10 mm2 / AWG 6
Terminal block
25 mm2 / AWG 2
Terminal block
50 mm2 / AWG 0
Terminal block
50 mm2 / AWG 0
Terminal block
95 mm2 / AWG 000
Terminal block
95 mm2 / AWG 000
Weight
(Kg)
0,8
0,8
1,3
1,6
2,7
4,1
5,9
7,9
8,5
FVNSB
A
B
C
D
E
F
G
H
Three Phase + Neutral Line Filters
Three-Phase + Neutral Filters for Industrial Applications
(8-200A)
8A
16 A
25 A
36 A
64 A
80 A
120 A
160 A
200 A
120
143
80
115
80
127.5
6.5
M6
120
143
80
115
80
127.5
6.5
M6
130
153
115
125
90
137.5
6.5
M6
130
153
115
125
90
137.5
6.5
M6
160
153
125
125
100
137.5
6.5
M10
230
163
125
135
120
147.5
6.5
M10
250
170
140
140
200
153.5
6.5
M10
280
170
170
140
230
153.5
6.5
M10
280
170
170
140
230
153.5
6.5
M10
317
Three Phase + Neutral Line Filters
FVNSB
318
Three-Phase + Neutral Filters for Industrial Applications
(8-200A)
64 120A
160 200A
N-X
General Specifications
Output Ferrites (N-X) are especially effective
in reducing electromagnetic interference
from the motor cable, as they introduce an
impedance between the Inverter and the
motor. Output ferrites are particularly useful
in reducing electrical noise in the frequency
range 5 to 20 MHz, as there is no other
suitable noise suppression means in this
frequency range. Output ferrites should
be placed around the cable between the
Inverter and Motor, as near as possible to the
Inverter. The cable (excluding earth wires and
shielding) should pass through the ferrite at
least twice.
Output Ferrites
Inverter Output Ferrites
319
N-X
Output Ferrites
Inverter Output Ferrites
320
Product List
Type
N1
N2
N3
Number of turns
2
3
4
2
3
4
2
3
4
Wire section
10mm2
6mm2
4mm2
16mm2
10mm2
6mm2
50mm2
35mm2
25mm2
Inductance
38µH
86µH
153µH
44µH
90µH
176µH
25,6µH
57,6µH
102µH
Max Current
60A
45A
30A
90A
65A
46A
150A
100A
75A
H
50mm
65mm
110mm
L
86mm
105mm
150mm
G
24mm
25mm
50mm
D
21mm
28mm
50mm
d
48mm
64mm
108mm
F
4mm
4mm
5mm
X
70mm
125mm
Y
11,5mm
89mm
12,5mm
30mm
FOVT
dV/dt Output Filters
DV/DT Output Filters (8-70A)
General Specifications
Maximum operating voltage: 550V±15.
Operating frequency: 50-60Hz.
Hipot test voltaje: L/N -> PE: 3000Vdc 2s.
Li-Lj: 2250Vdc 2s.
Application class:
HMF Acc. TO DIN 40040
(-25ºC/+100ºC/95% RH, 30d).
Flammability class: UL 94 V2.
Inverter Switching Frequency: 4-16kHz.
Max. Length of motor cable: 50m.
Electrical schematics
dV/dT Output Filter
Output 3 phase filter for inverter.
Minimizes Frequency Inverter dV/dT Values.
For long motor cables.
Increases motor life.
Reduces motor heating.
Product List
Type
I@50ºC
L
CX
CY
L leakage
Connection
Weight
±g
FOVT-008B
FOVT-016B
8 Amp
16 Amp
0,2 mH
0,2 mH
4,7 nF
4,7 nF
100 nF
100 nF
258 µA
258 µA
4mm2
4mm2
1600
2200
FOVT-025B
FOVT-036B
25 Amp
36 Amp
0,2 mH
0,2 mH
4,7 nF
4,7 nF
100 nF
100 nF
258 µA
258 µA
6mm2
10mm2
4500
5800
FOVT-055B
55 Amp
0,2 mH
10 nF
70 Amp
0,08 mH
10 nF
320 µA
320 µA
16mm2
25mm2
6500
FOVT-070B
100 nF
100 nF
7200
321
FOVT
dV/dt Output Filters
DV/DT Output Filters (8-70A)
Fast switching generated by inverter IGBTs causes high voltage ramps (greater than 4000V/
µs), that may be even higher in the motor windings. The fast switching can also shorten the
motor life and limit maximum cable lengths.
By using a PREMO EMC dV/dT filter, you can guarantee that the maximum peak voltage
will be under 1000V, with a dV/dT value less than 500 V/µs.
This voltage peak suppression will also reduce EMI interference from the inverter, will
increase its life and improve its performance.
FOVT-008B
FOVT-016B
FOVT-025B
FOVT-036B
FOVT-055B
FOVT-070B
322
A
99
150
231
350
350
380
B
58
56
71
81
81
90
C
105
100
119
149
149
180
D
85
126
151
300
300
320
E
51
85
115
325
325
345
F
95
116
135
110
110
120
G
5,3
5,3
5,3
6,5
6,5
8,5
H
M6
M6
M6
M6
M6
M8
FOVT
Motor cable length (M) at Inverter switching
frequency based on 400VAC, @40°C
Continuous Operation
Type
4KHz
8KHz
FOVT-008B
35
15
FOVT-016B
FOVT-025B
35
15
50
25
FOVT-036B
50
25
FOVT-055B
50
25
FOVT-070B
50
25
dV/dt Output Filters
DV/DT Output Filters (8-70A)
323
CFT
Feedthrough Filters
Single Line C-Circuit (10-250A)
General Specifications
Maximum operating voltage: 250VAC / 400VDC.
Operating frequency: DC - 60Hz.
Hi-pot test voltage: L/N-›PE: 3000Vdc 2s.
Climatic category: HPF (40/085/56)
(-40ºC/+85ºC/95% RH, 30d).
MTBF: > 0.3 Million Hours@40°C, 230VAC
Flammability class: UL 94 V0.
Single Line, C Circuit
For Telecom, Military and Industrial application.
Compact size and easy to install.
Electrical schematics
Product List
Rated
Current (A)
@40ºC
Rated
Capacitance
@1KHz, 25 ºC
Leakage
Current
250VAC/
50Hz (mA)
Termination
Torque
on S
(Nm)
Mounting
Thread
Weight
(gr)
X-10290-013
X-10290-018
10
16
4.7 nF
100 nF
0.5
12.0
M3
M4
0.5
1.2
M10 x 1
M12 x 1
25
35
X-10290-019
X-10290-020
32
63
100 nF
100 nF
12.0
12.0
M4
M6
1.2
2.5
M16 x 1
M16 x 1
35
45
X-10290-021
100
100 nF
12.0
200
100 nF
12.0
5.0
8.0
M20 x 1
M24 x 1
120
X-10290-023
M8
M10
X-10290-022
250
100 nF
12.0
M12
11.0
M31 x 1.5
200
Type
324
140
CFT
Feedthrough Filters
Single Line C-Circuit (10-250A)
Mechanical dimensions (mm)
A
B
C
D
E
F
G
10A
16A
32A
63A
100A
200A
250A
19
10
16
13
15
M3
M10 x 1
30
14
18
22
25
M4
M16 x 1
30
14
18
22
25
M4
M16 x 1
30
14
18
26
25
M6
M16 x 1
33
16
32
27
32
M8
M20 x 1
33
19
40
27
38
M10
M24 x 1
42
19
46
41
54
M12
M32 x 1.5
Installation Guide
- The torque applied to the screw cannot exceed max level.
- Filter metal housing must be well connected to cabinet panel by electrically and make
good grounding.
- The input & output wires should be separated to avoid noise coupling.
- Input wire of filter connection should be short and it will help to minimize radiated
interferences.
- Make good insulation around the connection part to avoid short circuit.
- Further information, please contact PREMO Technical person.
325
CFT
Feedthrough Filters
Single Line C-Circuit (10-250A)
326
Insertion Loss
PIFT
Feedthrough Filters
Single Line Pi-Circuit (10-63A)
General Specifications
Maximum operating voltage: 250VAC / 400VDC.
Operating frequency: DC - 60Hz.
Hi-pot test voltage: L/N-›PE: 3000Vdc 2s.
Climatic category: HPF (40/085/56).
(-40ºC/+85ºC/95% RH, 30d).
MTBF: > 0.3 Million Hours@40°C,230VAC
Flammability class: UL 94 V0.
Single Line, Pi Circuit
For Telecom, Military and Industrial application.
Compact size and easy to install.
High Current version is available.
Electrical schematics
Product List
Rated
Current (A)
@40ºC
Rated
Capacitance
@1KHz, 25 ºC
Leakage
Current
250VAC/
50Hz (mA)
Termination
Torque
on S
(Nm)
Mounting
Thread
Weight
(gr)
X-10290-014
X-10290-015
10
16
2 x 10 nF
2 x 22 nF
2.4
5.0
M3
M4
0.5
1.2
M12 x 1
M16 x 1
45
70
X-10290-016
X-10290-017
32
63
2 x 47 nF
2 x 470 nF
10.0
100
M4
M6
1.2
2.5
M24 x 1
M32 x 1.5
135
420
Type
327
PIFT
Feedthrough Filters
Single Line Pi-Circuit (10-63A)
Mechanical dimensions (mm)
A
B
C
D
E
F
G
10A
16A
32A
63A
66
12
16
17
20
M3
M12 x 1
69
14
18
22
25
M4
M16 x 1
101
14
18
22
25
M4
M16 x 1
118
19
26
41
54
M6
M32 x 1.5
Installation Guide
- The torque applied to the screw cannot exceed max level.
- Filter metal housing must be well connected to cabinet panel by electrically and make
good grounding.
- The input & output wires should be separated to avoid noise coupling.
- Input wire of filter connection should be short and it will help to minimize radiated
interferences.
- Make good insulation around the connection part to avoid short circuit.
- Further information, please contact PREMO Technical person.
328
PIFT
Insertion Loss
Feedthrough Filters
Single Line Pi-Circuit (10-63A)
329
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
330
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
331
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
332
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
333
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
334
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
335
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
336
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
337
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
338
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
339
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
340
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
341
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
342
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
343
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
344
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
345
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
346
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
347
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
348
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
349
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
350
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
351
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
352
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
353
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
354
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
355
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
356
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
357
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
358
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
359
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
360
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
361
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
362
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
363
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
364
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
365
PREMO EMC Filters Housing mechanical dimensions
HOUSING
Mechanical dimensions
366