SMA Style Coaxial Connector DM Series Characteristic Impedance 50 Ω OUTLINE Lock Type Screw DM series is a SMA connector which conforms to MIL-PRF-39012. It is compact and tough 50 Ω coaxial connector which designed for compact-sized and higher frequency communication device. Screw lock coupling enables reliable connection. Compatible to other SMA style connectors. Crimp, soldering and clamp types are available. APPLICATIONS CONFORMING STANDARD Base Station, Telecom, Wireless LAN, GPS MIL-PRF-39012 SPECIFICATIONS Characteristic Impedance Rated Voltage Dielectric Withstanding Voltage 50 Ω 500VAC 1000V AC(r.m.s.) for1 minute Contact Resistance 3m Ω Max. Oparating Temperature -55 〜 +85℃ Insulation Resistance V.S.W.R. 1000M Ω Mim. at 500V DC 1.05 + 0.01 x f (GHz) ＊ The specifications are typical but may not apply to all connectors. Please check the specifications on each item with its drawing from us when you use. MATERIAL/FINISH Item RoHS Compliant Compliant Material / Finish Shell (Body) Copper Alloy or Stainless Steel / Au, Ag or Ni Plating Contact Copper Alloy / Au or Ag Plating Coupling Ring Insulator Copper Alloy or Stainless Steel / Au, Ag or Ni Plating PTFE ※ We are providing the standard item on this catalogue. Other materal(Brass, Stainless steel) are also available. Please contact our sale office. ※ Notice for mating connectors When screwng up the coupling ring, please screw up by hand and tighten by toque wrench. ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. 121226 http://www.ddknet.co.jp DM Series Unit：mm ○ Straight Plug Connector Crimp Type φA φ A （L） Cable Size DM-SP-1.5DHQS-CR1-2 DM-P-58U-CR-BS-CF (L) Finish Applicable Part Number 1.5D-2V , 1.5D-2W RG-58A/U 2.5D-2V φA DM-SP-2.5DV-CR1-CF Ni 1 CR-H-1156 6.25 24.4 Au Au Au 2 CR-H-1105 Outer Center Conductor Conductor ☆ Assembly Coupling Instruction Crimp Tool 5.9 19.2 Ni Au Ni 3 CR-H-1163 Ni Au Ni 4 CR-H-1163 DM-P-1.5D2V-CR-BS-CF (L) 2.5D-QEV Crimp Tool Au φ A （L） Cable Size Assembly Instruction Ni Finish Applicable Part Number Coupling 19.3 4.8 1.5D-HQ・SUPER Outer Center Conductor Conductor DM-SP-2.5DHQS-CR1-1 2.5D-HQ・SUPER 5.9 18.9 DM-SP-2.5DW-CR1-CF 2.5D-2W 5.9 18.8 Passivation Au Passivaion 5 CR-H-1163 3D-2W 7.6 24.2 Au Au 6 CR-H-18293 DM-P-3DW-CR-CF Au DM-SP-2.5DV-CR1-CF for Semi-Rigid, Semi-Flexble Cable φA Part Number (L) Applicable Cable Size UT-85 DM-P-85-SO-BS-2-CF FCCAVG1 3.5 Applicable Part Number Cable Size DM-SP-141-SO-2-D1-CF UF141A DM-P-85-SO-BS-2-CF (14.2) DM-SP-141-SO-2-D3-CF FCCAVG0 UF-141A FCCAVG0 FCCAVGO-4.6 Applicable Part Number Cable Size Finish Assembly Outer Center Coupling Instruction Conductor Conductor φ A （L） 13.7 Ni DM-SP-141-SO-2-D1 DM-P-141-SO-D1-CF FCCAVG0 Ag Ag Utilize center conductor of the applicable cable 8.7 Moreover, the characteristic and the specification of the published product are the reference values. http://www.ddknet.co.jp 2 DM-P-141-SO-D1 Coupling Outer Center Conductor Conductor Au Utilize center conductor of the applicable cable Assembly Instruction Ag Ni Finish （L） ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Please confirm the content with the latest delivery specifications when you use the product. Ni Finish Outer Center Conductor Conductor UT-141A (L) Au Coupling Ni Assembly Instruction DM Series Unit：mm ○ Right Angle Plug Connector Crimp Type 8 六角対辺幅 １０ □7 7 Finish Applicable Part Number (L1) （L2） Outer Center Conductor Conductor Cable Size (L2) (15) 1.5D-2V, 1.5D-2W 1.5D-HQ・SUPER 17.8 17.0 Ni Au Ni 7 CR-H-1156 DM-LP-2.5DHQS-CR1-2-CF 2.5D-HQ・SUPER 17.8 17.0 Ni Au Ni 8 CR-H-1163 DM-LP-3D2W-CR1-CF 18.8 21.2 Ni Au Ni 9 CR-H-18923 8 DM-LP-1.5DHQS-CR1 4.8 Assembly Crimp Coupling Instruction Tool 3D-2W (L1) for Semi-Rigid, Semi-Flexible Cable Finish Assembly (L1) （L2） Outer Center Coupling Instruction Conductor Conductor (L2) Applicable Part Number DM-LP-1.5DHQS-CR1 Cable Size 23924 注１．符号①，③，⑩は添付品とする。 DM-LP-85-SO-4-CF (L1) DM-LP-141-SO-4-D1-CF UT-85 FCCAVG1 UT-141A FCCAVG0 18.0 11.0 Ni Au Ni 19.0 11.4 Ni Au Ni ○ Jack Connector for Semi-Rigid, Semi-Flexible Cable DM-LP-85-SO-4-CF 9 φA Part Number Applicable Connector DM-SJ-141-SO-1-CF (L) DM-SJ-85-SO-CF UT-141A FCCAVG0 UT-85 FCCAVG1 Finish Assembly Outer Center Instruction Conductor Conductor φA L 6.4 13.3 Ag Ag 4.0 12.5 Ni Au ○ Panel Jack Connector for Semi-Rigid, Semi-Flexible Cable DM-SJ-141-SO-1 Part Number φA 8.60 4-φ2.6 1.7 9.55 L DM-PJ-141-SO-DI 8.60 DM-PJ-141-SO-D3-CF □12.7 +0.1 0 4-φ2.75 ☆ 8.60 0.05 UT-141A FCCAVG0 UT-141A FCCAVGO UT-85 FCCAVG1 L 4.7 12.7 Ni Au 4.7 12.7 Ni Au 3.4 12.7 Ni Au 8.60 .5 φ6 DM-PJ-85-SO-D3 Cable Size PCB Mounting Dimensions ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp DM-PJ-141-SO-D1 3 Finish Assembly Outer Center Instruction Conductor Conductor φA 0.05 .1 +0 0 Applicable DM Series Unit：mm 8.64 1.27 9.5 B L DM-SR-18-CF 4.0 1.5 15.0 Ag Ag DM-SR-20-CF 6.0 1.0 16.5 Ag Ag DM-SR-27-CF 5.0 1.0 15.5 Ag Ag □12.7 +0.1 φ4.2 0 +0.1 ４-φ2.75 0 8.64 0.05 ４-φ2.7 PCB Mounting Dimensions 8.64 8.64 0.05 φ1.27 ４-φ2.7 A L 5,1 14.6 Ag Ag DM-SR-28-CF 6.0 15.5 Ag Ag DM-SR-31-CF 3.0 12.5 Ag Ag 8.64 0.05 1.65 □12.7 1.65 ＋0.1 0 ４-φ2.75 8.64 L 取付参考寸法 □12.7 8.64 0.05 φ4.2 ＋0.1 ４-φ2.75 0 φ1.27 0.05 8.64 0.05 8.64 8.64 φ4.11 ＋0.1 0 φ4.2 DM-SR-18 ４-φ2.7 ＋0.1 0 A 0.05 Outer Center Conductor Conductor 8.64 φ1.27 L DM-SR-23-CF 8.64 取付参考寸法 8.64 9.5 A 9.5 Finish Part Number PCB Mounting Dimensions DM-SR-18 DM-SR-23-CF 1.65 B 取付参考寸法 9.5 L ４-φ2.7 8.64 Part Number □12.7 A B L DM-SR-23-CF 2.0 4.0 15.5 DM-SR-1 A B 1.65 8.64 8.64 9.5 L 4.0 8.7 22.2 Ag Ag DM-SR-24-CF 5.0 6.5 21.0 Ag Ag DM-SR-30-CF 4.0 6.5 20.0 Ag Ag ＋0.1 0 ４-φ2.7 ＋ ０． １ ４− ２． ７５ ０ ４． ２ 8.64 8.64 0.05 8.64 8.64 0.05 8.64 0.05 φ4.11 0.62 8.64 1.65 9.5 ４-φ2.75 Part Number 0.05 ＋0.1 Moreover, the characteristic and the specification of the published product are the reference values. 0 ４-φ2.75 Please confirm the content with the latest delivery specifications when you use the product. 取付参考寸法 取付参考寸法 0.05 8.64 DM-SR-15-CF PCB Mounting Dimensions ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. 0.05 Ag φ4.2 8.64 8.64 Ag 取付参考寸法 ＋0.1 0 □12.7 http://www.ddknet.co.jp＋0.1 φ4.2 0 Finish Outer Center Conductor Conductor DM-SR-19-CF ＋0.1 0 0.05 19.9 8.64 □12.7 8.64 8.7 8.7 8.64 0.05 0.05 ＋０． ０ １ PCB Mounting Dimensions 1.65 9.5 ＋０． １ ４-φ2.7 19.9 ０ ＋0.1 φ4.2 0 1.7 ４． ２ ＋ ０． １ ４− ２． ７５ ０ 8.64 0.05 1.7 ＋0.1 0 ４-φ2.75 8.64 0.05 0.62 φ4.11 ＋0.1 φ4.2 0 8.64 Au DM-SR-15-CF ４-φ2.75 □12.7 Passivation 8.64 0.05 φ1.27 φ4.11 取付参考寸法 Finish Outer Center Conductor Conductor DM-SR-19-CF 4 １ ４−∅２．７５＋０． ０ ∅４．２＋０．１ ±0.05 +0.1 φ4.2 0 A Outer Center Conductor Conductor .64 L +0.1 ４-φ2.75 0 8.64 Finish A 8.64 0.05 B □12.7 ４-φ2.7 1.65 Part Number 8.64 9.5 L 1.27 φ4.11 A B A ４-φ2.7 1.65 8.64 φ4.11 ○ Receptacle Connector D φ1.27 12.2 φ4.11 .8 16 φ 2-φ2.75 DM Series ○ Receptacle Connector Unit：mm 1.65 1 6 5.8 9.5 15.5 +0.1 0.05 2-φ2.75 0 12.2 +0.1 0 φ1.27 .2 φ4 DM-SR2-18-CF Ag Ag 6.1 5.8 9.5 Center Conductor Conductor 0.05 1.65 1 6 Finish Outer Part Number 12.2 φ4.11 .8 16 φ 2-φ2.75 15.5 PCB Mounting Dimensions +0.1 5.8 .8 16 φ 2-φ2.75 DM-SR2-18 +0.1 0 2-φ2.75 +0.1 Finish Center Conductor Conductor 14.6 Ag Ag 5.1 14.6 Au Au DM-SR2-22-CF 3.1 12.6 Ag Ag A B L 2.5 5.0 17.0 Ni Au 4.0 5.5 19.0 Ni Au Part Number Outer Finish Center 0.1 Conductor Conductor DM-SR2-4-CF 12.2 0.05 φ1.27 6.1 φ4.11 12.2 取付参考寸法 5.8 取付参考寸法 L Outer DM-SR2-1-D1-CF DM-SR2-8-CF DM-SR2-1-CF DM-SR2-1-CF DM-SR2-8-D1-CF 1.65 9.5 B L PCB Mounting Dimensions φ4.3 0 A 12.2 6.1 取付参考寸法 A DM-SR2-18 DM-SR2-1-CF 5,1 0.1 0.1 12.2 0.05 5.8 0 .1 Part Number 0.05 1.65 9.5 1.65 A 9.5 L L 2-φ2.75 0 +0.1 2-φ2.75 0 6.1 12.2 φ4 + 0 .2 φ 0 4.1 + .2 0 12.2 6.1 0.05 φ1.27 φ1.27 取付参考寸法 ２-M2.6 0.45 ２-M2.6 0.45 .8 A 12.2 16 φ .8 .2 φ4 16 φ +0.1 0 0.05 +0.1 2-φ2.75 0 4.0 5.5 19.0 Au Au DM-SR2-9-CF 1.5 4.0 15.0 Ag Ag DM-SR2-15-CF 1.5 3.2 14.2 Ni Au A B L PCB Mounting Dimensions 12.2 12.2 +0.1 0.05 φ4.2 0 1.65 6.7 9.5 6.1 B A Center Conductor Conductor DM-SR2-10-CF 6.9 2.9 16.4 Ag Ag DM-SR2-11-CF 4.4 2.9 13.9 Ag Ag +0.1 0.1 +0.1 0 DM-SR2-16-CF 0.05 6.7 Outer Finish Center Conductor Conductor 6.11 16.5 取付参考寸法 Part Number 12.2 12.2 φ17 2-φ2.75 0 φ4.2 φ1.27 φ4.11 2-φ2.7 1.65 9.5 Finish DM-SR2-4-CF 取付参考寸法 2 Outer PCB Mounting Dimensions L 5 Part Number 0.1 φ17 4-φ2.75 φ1.27 φ4.11 ２-φ2.7 PCB Mounting Dimensions Ni DM-SR2-10-CF ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 5 DM-SR2-16-CF Au DM Series L Unit：mm B A 12.5 1.65 8.64 B A 4-φ2.7 +0.1 0 8.64 L DM-LR-7-CF 6.0 2.0 20.5 Ag Ag DM-LR-8-CF 4.0 6.5 23.0 Ag Ag Outer Center Conductor Conductor 0.05 8.64 17 2.9 12.22 2-φ2.7 Part Number 6.7 φ1.27 φ4.11 15.7 8.64 4.4 0.05 0.05 1.65 B PCB Mounting Dimensions +0.1 0 12.5 Finish A φ4.2 +0.1 0 8.64 8.64 □12.7 +0.1 0 4-φ2.75 φ4.2 16.9 Part Number 4-φ2.75 8.64 □12.7 φ1.27 φ4.11 15.7 8.64 4-φ2.7 0.05 L 12.5 1.65 φ1.27 φ4.11 15.7 ○ Right Angle Receptacle Connector DM-LR2-CF 取付参考寸法 DM-LR2 DM-LR2-2-CF 12.2 19.15 11.2 φ1.27 0 Outer Center Conductor Conductor Ag 16.9 9.5 4.1 1.7 Part Number .9 15 2-M2.6 φ 15.7 11.2 φ1.27 6.6 DM-LR2-5-CF DM-LR2-2-CF Ag Finish Part Number 2-M2.6 .9 5 φ1 1.7 6.6 Ag DM-LR-7 0 DM-LR-7 16.9 取付参考寸法 9.5 4.1 Finish Outer Center Conductor Conductor Ag Finish Outer Center Conductor Conductor Ag Ag 12.2 12.2 0.1 +0.1 6.1 0.05 +0.1 φ4.2 0 φ1.2 3.5 5 11.5 2-φ2.75 0 4-□0.92 PCB □6 Mounting Dimensions 10 13.5 取付参考寸法 0.05 2.54 3.5 φ1.2 4-□0.92 10 □5.08 □6 13.5 Part Number 0.05 2.54 0.05 5 11.5 5-φ1.6 DM-LR-PC-CF 0.05 DM-LR2-5-CF PCB Mounting Dimensions 0.05 5-φ1.6 2.54 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. 0.05 0.05 取付参考寸法 Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 2.54 Moreover, the characteristic and the specification of the published product are the reference values. 6□5.08 0.05 DM-LR-PC-CF Finish Outer Conductor Ni Center Conductor Au DM Series Unit：mm ○ Dust Cap 1/4-36UNS-2B Flat Diameter：８ (60) (68.5) DM-RC-1-CF (8.5) (φ2.3) (φ2.5) Part Number Contact Plating Ni DM-RC-1-CF Flat Diameter:8 Part Number DM-RC-2-CF DM-RC-2-CF ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 7 Contact Plating Ni Parts Configuration DM Series Ferrule Unit：mm Body Contact ○ Assembly Insutruction（1） Parts Configuration １−１．片端結線においてのケーブル必要長 Ｌ Ferrule Body Contact 1 1. Necessary cable length in case of one side termination = L L2 L ＝ L1-7.7 ＝ L2+11.6 L1 Ferrule 2 Outer Conductor， Aluminum foil tape L2 24 3 5 Ｌ＝Ｌ1−７．７ ３−１．ケーブル端面を図示寸法に処理する。 4.8 1 L =L2+11.6 Center Conductor Insulator 3．Strip cable as shown dimension. fig.2. 注）内部導体及び外部導体に傷を付けない （Note）Be careful not to nick to outer conductor こと。 and center conductor. ３−２．内部導体に予備はんだを施す。 3-1．Pre-solder the center conductor. 注）はんだの熱により絶縁体を膨張，変形 （Note）Please be careful to not deform the insulator させないこと。 ２−１．ケーブルにフェルールを挿入する。 by heat. Pre-soldering 0.3 8 1.5 0.3 Ferrule Soldering 0.3 4. Solder up the contact to４−１． the center conductor of 内部導体にコンタクトをはんだ付けする。 the cable 注）はんだの熱により絶縁体を膨張，変形 Cable （Note）Please be careful to not deform the insulator ３−１．ケーブル端面を図示寸法に処理する。 させないこと。 Make sure there is no space. by heat. Outer Conductor， Insulator 注）コンタクトと絶縁体間に隙間のないこと。 Center Conductor Contact Aluminum foil tape （Note）No gap between contact and insulator. 注）内部導体及び外部導体に傷を付 注）はんだの盛り上がりは、 コンタクト外径に Pre-soldering Spread out こと。 （Note）When the solder is stick out, please shave 沿って削り取ること。 the extra solder. ３−２．内部導体に予備はんだを施す。 ５−１．外部導体及びアルミ箔テープの先端を拡げる。 注）はんだの熱により絶縁体を膨張， ５−２．ボディ組立をケーブ外部導体 （アルミ箔テープ）∼ 変 5．Spread the top of the outer conductor. させないこと。 絶縁体間に挿入し、突き当てる。 5-1. Insert the body into the cable between 注）アルミ箔テープは、ボディ外径に乗り上げること。 4.8 0.3 4 Aluminum foil tape lower limit position 1.5 0.3 0.3 Body 8 knurl Soldering outer conductor and aluminum foil tape. ４−１．内部導体にコンタクトをはんだ付けする 注）アルミ箔テープ端の図示下限位置以上に円周上の (Note）Ride aluminum foil tape on Body outer 一部が乗り上げられていれば良い。 dimension. 注）はんだの熱により絶縁体を膨張， 変形 但し、工程５−３． のフェルールが容易に通ること。 させないこと。 (Note）At least,ride a part of aluminum foil tape on ５−３．予め通しておいたフェルールを外部導体上に被せ、 注）コンタクトと絶縁体間に隙間のないこと body knurl. ボディ組立に突き当てかしめる。 はんだの盛り上がりは、 コンタクト外径 But ferrule of Step5-2 should 注） entry easily. Make sure there is no space. Contact Aluminum foil tape 注）ボディ組立∼フェルール間の隙間は、０．５以下 のこと。 沿って削り取ること。 注）かしめ後のクリンプハイトは、下図の位置にて ５−１．外部導体及びアルミ箔テープの先端を拡 表１の規格を満足すること。 Spread out Crimping Dies. A-R1 ↑ Aluminum foil tape lower limit position Ferrule ↑ Body 5-2. Slide ferrule on outer conductor until shall butt ５−２．ボディ組立をケーブ外部導体（アルミ箔テ body and crimp ferrule 絶縁体間に挿入し、 (Note) The gap between body and ferrule is within 0.5突き当てる。 Body knurl 注）アルミ箔テープは、ボディ外径に乗り上げ 注）アルミ箔テープ端の図示下限位置以上に 一部が乗り上げられていれば良い。 但し、工程５−３．のフェルールが容易 表１ ４．１２∼４．３５ 六角クリンプハイト（ａ，ｂ，ｃ三辺共） ３．０５∼３．１８ ディンプルクリンプハイト ５−３．予め通しておいたフェルールを外部導体 Aluminum foil tape ボディ組立に突き当てかしめる。 0.5 Max. 3 Crimping Dies. A-R1 6 注）下記開口部寸法 （ボディ∼コンタクト間）を 注）ボディ組立∼フェルール間の隙間は、 ０ 満足すること。 のこと。 0.5 1 Body ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. 注）かしめ後のクリンプハイトは、下図の位置 表１の規格を満足すること。 ↑ 5 ２−１．ケーブルにフェルールを挿入する。 2．Insert the cable into the ferrule. １−１．片端結線においてのケーブル必要長 Ｌ （Note）Please confirm the direction of ferule Cable 13 Ｌ＝Ｌ1−７．７ =L2+11.6 Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp Ferrule ↑ 8 0.1 0.1 （ボディ∼コンタクト間） DM Series Unit：mm ○ Assembly Insutruction（2） Parts Configuration Parts Configuration Boot Ferrule Boot Ferrule Contact Body Body 1. The cable length require for the cable assembly L ＝ L1 ー 7.1 1 1 L1 Cable 2 2. Insert the boot and ferule into the cable. L1 Cable 2 3. Cut the cable as fig.3. （Note）Please be carefule to not damage the outer Sheath Outer Conductor Ferrule Center Conductor Insulator Boot conductor , insulator and center conductor. Pre-soldering 3 Sheath Outer Conductor Insulator Center Conductor 3-1. Pre-solder the center conductor. Pre-soldering （Note）Please be careful to not deform the insulator 6.3 0.2 by heat 2.0 0.2 9.0 0.2 Ferrule Boot 3 Contact 6.3 0.2 9.0 0.2 4 Soldering 2.0 Insulator 4 Contact Soldering Insulator 6 6 the extra solder. No gap Connector Body5. Spread the top of the outer conductor. Spread the top 0.1 Ferrule （Note）When the solder is stick out, please shave Connector Body Spread the top 5 by heat. （Note）No gap between contact and insulator. Contact No gap 5 4. Solder up the contact and center conductor. （Note）Please be careful to not deform the insulator 0.2 5-1. Insert the root of connector body between outer conductor and insulator. (Note）Please do not pick the outer conductor. 0.1 (Gap between body and contact) 0.1 Ferrule 0.1 6. Insert the connector body until the gap between body and contact is within 0.1±0.1. 6-1. Cover the ferule on the outer conductor and insert the cable until strike the top of the cable. 6-2. While the cable is touch the connector body, 0.1 0.1 crimp the ferule two points. Crimping Dies ：F (Gap between body （Note）Crimp point is nearest to the body first. and contact) （Note） The gap between body and ferule is within 0.5. 0.1 0.1 （Note）Crimp height is 5.38 〜 5.56. (Gap between body （Note）The gap between body and contact is within and contact) 0.1±0.1. (Gap between body and contact) Crimping Dies：F Crimping 0.5 max. Dies：F 0.5 max. Measuring position of crimp height 3.0 1.0 7 Measuring position of crimp height 3.0 1.0 7.Cover the boot on the ferule. 7 Boot ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Boot Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 9 DM Series Unit：mm Parts Configuration ○ Assembly Instruction（3） Parts Configuration Contact Ferrule Heat-shrinkable tube Body Contact Ferrule Heat-shrinkable tube Body L The cable length require for the cable assembly L ＝ L1+6 L L1 Heat-shrinkable tube 1 Heat-shrinkable tube 1 1. Insert the boot and ferrule into the cable. Ferrule L1 Ferrule Cable Outer Conductor Insulator Cable Center conductor 2 2 Outer Conductor Insulator +0.3 -0.5 2.0Center conductor Sheath 4.5 0.5 +0.5 0 10.5 Sheath 3 +0.3 2.0 -0.5 4.5 0.5 Soldering +0.5 10.5 0 Contact 3 No gap Spread the top 4 5 3. Solder up the contact with center conductor. （Note） When the solder is stick out, please shave the extra solder. （Note）No gap between contact and insulator. Soldering 4 2. Cut the cable as fig..2. Pre-soldering to the center conductor of the cable. （Note） Please be careful to not damage outer conductor, insulator and center conductor. Contact 4. Spread the top of the outer conductor. Insert the root of connector body between outer conductor and insulator. No gap Spread the top Ferrule 5 Ferrule Crimping Dies RFD-1 6 5. Cover the ferrule on the naked outer conductor and crimp. 0.5 max. （between body and ferule） Crimping Dies RFD-1 0.5 max. 6. Cover the heat-shrinkable tube on the ferrule and heat up the tube. （between body and ferule） 6 Heat-shirinkable tube ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Heat-shirinkable tube Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 10 Parts Configuration DM Series Unit：mm ○ Assembly Instruction（4） Contact Ferrule Parts Configuration Body Contact Ferrule Body 1 1 1. The cable length require for the cable assembly. L=L1 ー 8 =L2 ＋ 11 L2 2 L1 1 1 2 the cable. 2. Insert the ferrule into L2 Cable 3 L1 Ferrule 2 Outer Conductor Aluminum foil tape L1 L1 Ferrule Insulator Center conductor (Pre-soldering) Cable 35.5 0.3 Outer Conductor 7.0 0.3 Aluminum foil tape （8.7） 4 5 Insulator 0.3 Center conductor 1.7 (Pre-soldering) Soldering 5.5 2 1.7 7.0 0.3 （8.7） 0.3 3 0.3 外部導体 絶縁体 1.7 Contact 内部導体 (予備はんだ) 4. Solder up the contact with center conductor. 4 insulator by supplying （Note）Don't melt to the はんだ付け 5.5 0.3 （Note）No gap between contact and insulator. 7.0 （8.7） コンタクト 1.7 （Note）If it get solder on outside surface of Contact, No the gaptop Spread Aluminum foil tape Body lower limit position knurl 5.5 7.0 アルミ箔テープ （8.7） remove solder5 Aluminum foil tape Body 5 lower limit position knurl フェルール excessive heat. No gap Soldering ケーブル 3. Cut the cable as fig.2. 3 （Note）Please be carefule to not 外部導体 damage the絶縁体 center 内部導体 conductor and outer conductor. (予備はんだ) 3-1. Pre-solder the centerアルミ箔テープ conductor. ケーブルthe insulator （Note）Please be careful to not deform by heat Contact 0.3 4 フェルール 4 隙間のないこと はんだ付け コンタクト 5. Spread the top of the outer conductor. 5-1. Insert the body into the cable between 先端を拡げる 隙間のないこと outer conductor and aluminum foil tape. 5 (Note）Ride aluminum foil tape on Body outer dimension. (Note）At least,ride a part of aluminum foil tape on body knurl. 先端を拡げる But ferrule of Step5-2 should entry easily. ボディ組立 5-2. Slide ferrule on outer conductor until shall butt body and crimp ferrule かしめダイス RFD-1 (Note) The gap between body and ferrule is within 0.5. Spread the top Connector Body Crimping Dies RFD-1 ボディ組立 かしめダイス RFD-1 Connector Body Crimping Dies RFD-1 フェルール Ferrrule ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp Ferrrule 11 フェルール 5 Parts Configuration DM Series 5 Unit：mm ○ Assembly Insutruction（5） Parts Configuration Ferrule Heat-shrinkable tube Contact Ferrule Heat-shrinkable tube 1 Contact Body Body 1. The cable length require for the cable assembly. L ＝ L1 ー 7.0 L 1 L1 2 L Sheath Outer Conductor Insulator Center Conductor L1 Pre-soldering 2. Cut the cable as fig.2. Sheath Outer Conductor Insulator （Note）Please be careful to not damage the outer 2.3 0.3 2 Cable Center Conductor conductor, insulator and center conductor. 0.3 0.3 2.2 7.3 Pre-soldering 2-1. Pre-soldering the center conductor. （9.5） Soldering 2.3 0.3 0.3 0.3 2.2 7.3 Contact （9.5） Cable 3 3 Ferrule 4 Ferrule Heat-shrinkable 4 tube Heat-shrinkable tube Soldering No gap Contact Insulator No gap （Note）Please be careful to not deform the insulator by heat 3. Solder up the contact with center conductor. （Note）Please be careful to not deform the insulator by heat. （Note）No gap between contact and insulator. （Note）When the solder is stick out, please shave the extra solder. Insulator Spread the top 4. Insert the heat-shrinkable tube and ferrule into the cable. 4-1．Spread the top of outer conductor. 4-2．Insert the body into the cable between outer Spread the top conductor and aluminum foil tape. 4-3．At least,ride a part of aluminum foil tape on body knurl. Crimping Dies 4-4．Crimp the ferrule. (Crimping Dies : RFD-1) RFD-1 （Note）The gap between connector body and ferrule is within 0.5. Crimping Dies RFD-1 Ferrule 5 Ferrule 5 5．Cover the heat-shrinkable tube on the root of the connector body and heat up the tube. Heat-shirinkable tube ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Heat-shirinkable tube Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 12 DM Series Parts ○ Configuration Assembly Unit：mm Instruction（6） Parts Configuration Ferrule Boot Contact Ferrule Boot Body Contact Body 1 1 2 3 L1 Boot 2 Cable 1. The cable length require for the cable assembly. L ＝ L1 ー 7.2mm Ferrule Boot Ferrule Insulator Cable 0 7.0 -0.5 +0.5 10.3 0 0 Insulator （Note）When the solder is stick out, please shave the extra solder. Body No gap Body 5. Spread the outer conductor and insert into the connector body. Body Ferrule Contact 2.18 2.18 0.15 6. Cover the ferrule on the naked outer conductor and crimp. (Crimping Dies : D-P) 0.5 max. （between body and ferule） Crimping Dies Boot D-P 7 0.15 Body Ferrule Crimping Dies D-P 7 4. Solder up the contact with the center conductor. （Note）No gap between contact and insulator. Soldering Contact No gap Outer Conductor Contact 6 And pre-solder the center conductor. 0 Soldering 2.0 --0.5 Contact Outer Conductor 5 3. Cut the outer conductor, insulator and center Center Conductor Pre-soldering conductor as fig.3. 0 +0.5 0 5 Center Conductor 12.3 Pre-soldering 2.0 --0.5 Insulator10.3 4 the sheath as fig.2. Insulator Outer Conductor 7.0 -0.5 4 Outer Conductor 2. Insert the boot and ferrule into the cable and strip 12.3 Outer Conductor 3 6 Outer Conductor L1 0.5 max. （between body and ferule） 7. Cover the boot on the root of the connector body. Boot ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 13 DM Series Unit：mm 結線作業（9）○ Assembly Instruction（7） 結線作業（9） Parts Configuration Parts Configuration Heat-shrinkable tube Heat-shrinkable 工程１ 工程１ 1 tube 工程２ 1 2. Heat-shrinkable tube andＬ＝Ｌ1+0.5 ferrule into the cable. fig.2. L1 Outer Conductor， Heat-shrinkable tube Aluminum foil tape 3. Cut the cable as fig.3. （Note）Please be careful to not damage the outer ３−１． ケーブル端末を図示寸法に処理する。 Pre-soldering 注） 内部導体、絶縁体、 外部導体に傷を付けないこと。 conductor, insulator and center conductor. ３−２． 内部導体に予備はんだを施す。 0 3-1. Pre-soldering the center conductor. 1.3 -0.3 注） はんだの熱により絶縁体を変形，膨張させないこと。 Insulator （Note）Please be careful to not deform the insulator Center Conductor by heat ３−１．ケーブル端末を図示寸法に処理する。 Pre-soldering Center Conductor Cable Outer Conductor， foil tape Aluminum Sheath 4 Aluminum foil tape minimum point Sheath 6 ３−２． 内部導体に予備はんだを施す。 注） はんだの熱により絶縁体を変形， 膨張させないこと。 4. Spread the top of the outer conductor. ４−１．外部導体及びアルミ箔テープの先端をを拡げる。 4-1.（Note）At least,ride apart of aluminum foil ４−２． ボディ組立をケーブル外部導体 tape on Body knurl.（アルミ箔テープ）∼絶縁体間 に挿入し、突き当てる。 But Ferruleボディの外側へ乗り上げ、 of Step5-1 should entry easily. 注） アルミ箔テ−プは、 テープの一部が ボディローレット部にかかっていればよい。 （Note）The center conductor is caught in the 但し、工程５−１のフェルールが容易に通ること。 contact slit enough. 注） 内部導体がコンタクトスリットに半分以上収まっていること。 6 Aluminum foil tape minimum point 4 注） 内部導体、絶縁体、外部導体に傷を付けないこと。 0 1.3 -0.3 Laurette Aluminum foil tape 工程４ ２−１． ケーブルに熱収縮チューブとフェルールを挿入する。 Ferrule Insulator 11 工程４ ２−１． ケーブルに熱収縮チューブとフェルールを挿入する。 Ferrule Cable 3 工程３ Body １−１． 片端結線においてのケーブル必要長 Ｌ1 Heat-shrinkable tube 3 工程３ Body 1. The １−１． cable片端結線においてのケーブル必要長 Ｌ1 length require for the cable assembly. （mm） L=L1+0.5 Ｌ＝Ｌ1+0.5 2 2 Ferrule Ferrule L1 工程２ Blind Screw Blind Screw 11 Laurette ４−１．外部導体及びアルミ箔テープの先端をを拡げる。 Crimping Aluminum foilDies tape A-R1 工程５ ↑ A3 5 Ferrule 工程６ 5 6 Crimping Dies Center Conductor A-R1 Ferrule 工程６ 5-1. Crimp the ferrule. (Crimping Dies : A-R1) 注）ボディ組立とフェルール間の隙間は、０．５以下のこと。 （Note）The gap between body and ferrule is within 0.5. 注）かしめ後のクリンプハイトは、 下図の位置にて表１の規格を満足すること。 ↑ ↑ A3 工程５ ４−２． ボディ組立をケーブル外部導体（アルミ箔テープ）∼絶縁 に挿入し、突き当てる。 注） アルミ箔テ−プは、 ボディの外側へ乗り上げ、 テープの一部が ５−１． フェルールを外部導体上に被せ、 ボディ組立に突き当てる。 ボディローレット部にかかっていればよい。 工程５−１のフェルールが容易に通ること。 5. Cover the ferrule但し、 on the naked outer conductor. 注） 内部導体がコンタクトスリッ トに半分以上収まっていること。 ５−２． かしめダイス ： Ａ−Ｒ１にてフェルールをかしめる。 ↑ ５−１． フェルールを外部導体上に被せ、 ボディ組立に突き当 Contact Center Conductor 6 工程７ ５−２． かしめダイス：Ａ−Ｒ１にてフェルールをかしめる。 Blind Screw 7 Heat-shrinkable tube 6. Solder the contact with center conductor. 注）ボディ組立とフェルール間の隙間は、０．５以下のこと。 注）かしめ後のクリンプハイトは、下図の位置にて表１の規格を満足すること。 7. Screw６−１． up コンタクトと内部導体をはんだ付けする。 the blind screw on the body.Screw torque 9.8N・cm（1Kgf・cm） 7-1.Cover the heat-shrinkable tube on the root of the connector body and heat up the tube. ７−１． ボディ組立に盲蓋を９． ８Ｎ・ｃｍ （１Ｋｇｆ・ｃｍ） のトルクで締め付ける。 Contact ７−２．予め通しておいた熱収縮チューブを図示のように被せ収縮させる。 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 7 Blind Screw 14 数量 符号 承認 図番 設計 ６−１． コンタクトと内部導体をはんだ付けする。 材質 部品名称 形式 品名 処理・他 DM Series Unit：mm Parts Configuration ○ Assembly Instruction（8） Parts Configuration Blind Screw Body Ferrule 1 Blind Screw Body Ferrule 1-1.片端結線においてのケーブル必要長 L1 L=L1+0.5 1. The cable length require for the cable assembly. L=L1+0.5 1-1.片端結線においてのケーブル必要長 L1 Ｌ Ｌ1 L=L1+0.5 2-1.同軸ケーブルにフェルールを挿入する。 1 Ｌ Ｌ1 2-1.同軸ケーブルにフェルールを挿入する。 3-1.ケーブル端面を図示寸法に処理する。 2. Cut the cable as fig.2. （注）ケーブル内部導体及び外部導体に （Note）Please be careful to not damage the 傷を付けないこと。 outer conductor and center conductor. 3-2.内部導体に予備はんだを施す。 2-1. Pre-solder the center conductor. 3-1.ケーブル端面を図示寸法に処理する。 2 Cable 2 3 Ferrule Outer Conductor Aluminum foil tape Sheath Pre-soldering Ferrule Cable 3 4 4 （注）ケーブル内部導体及び外部導体に 傷を付けないこと。 3-2.内部導体に予備はんだを施す。 Center Conductor 0 -0.3 Outer1.3 Conductor Aluminum foil tape 5.5 Sheath Cable 10.5 Body Aluminum foil tape knurl 3. Insert the ferule into the cable. Center Conductor Pre-soldering 0 Contact Slit -0.3 1.3 Cable Body Aluminum foil tape knurl 5.5 10.5 Crimping Dies RFD-1 Contact Slit 5 5 テープ間に挿入し、突き当てる。 contact slit enough. （注）内部導体がコンタクトスリットに （Note）Aluminum foil tape is inserted in the 半分以上収まっていること。 5-1.フェルールを外部導体上に被せ、ボディ body. （注）アルミ箔テープは、ボディの外側へ乗り上げテープ Body Crimping Dies RFD-1 4-1.外部導体及びアルミ箔テープを拡げる。 4-2.ボディ組立をケーブル外部導体∼アルミ箔 テープ間に挿入し、突き当てる。 4. Spread （注）内部導体がコンタクトスリットに the top of the outer conductor. 4-1. Insert the body into the cable between outer 半分以上収まっていること。 4-1.外部導体及びアルミ箔テープを拡げる。 （注）アルミ箔テープは、ボディの外側へ乗り上げテープの conductor and aluminum foil tape. 4-2.ボディ組立をケーブル外部導体∼アルミ箔 内径へ入れること。 （Note）Center conductor is caught in the Body 組立に突き当てる。 内径へ入れること。 5-2.フェルールをクリンプする。 5. Cover the ferule on the naked outer conductor. ダイス：RFD-1 5-1. Crimp （注）ボディ組立とフェルール間の隙間は、 the ferule. (Crimping Dies : RFD-1) （Note）The gap between body and ferule is 0.5以下のこと。 5-1.フェルールを外部導体上に被せ、ボディ within 0.5.組立に突き当てる。 Ferrule 5-2.フェルールをクリンプする。 ダイス：RFD-1 （注）ボディ組立とフェルール間の隙間は、 0.5以下のこと。 Soldering 6 Contact Ferrule 6-1.コンタクトと内部導体をはんだ付けする。 6. Solder the contact with center conductor. Soldering 6 Blind Screw 7 6-1.コンタクトと内部導体をはんだ付けする。 Contact 7. Screw up the blind screw on the body. Screw torque 9.8N・cm（1Kgf・cm） Blind Screw 7 7-1.ボディ組立てに盲蓋を9.8N・cm（1Kgf・cm）の トルクで締め付ける。 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 15 7-1.ボディ組立てに盲蓋を9.8N・cm（1Kgf・cm）の トルクで締め付ける。 Parts ConfigurationDM Series Blind Screw Washer ○ Assembly Instruction（9） Gasket Blind Screw Washer Parts Configuration Ferrule Body Gasket Ferrule 1 Unit：mm Body L2 1 1. The cable length require for the cable assembly. L=L1+0.6 =L2-3.4 1-1. Insert the ferule into the cable. L2 L1 Ferrule Cable L1 Cable 2 2 3 Ferrule Outer Conductor Insulator Center Conductor Pre-soldering +0.5 Outer Conductor 6.0 0 +0.5 10.0 0 Spread the top 3 Insulator Center Conductor 0 Pre-soldering 2.0 -0.5 Contact Slit +0.5 6.0 0 +0.5 10.0 0 Crimping Dies :D-P 3. Spread the top of the outer conductor. 3-1. Insert the body into the cable between outer conductor and insulator. （Note）The center conductor is caught in the contact slit enough. 0 2.0 -0.5 Contact Slit Body Spread the top 0.5 max. Ferrule 4 4. Cover the ferule on the naked outer conductor. 4-1. Crimp the ferule. (Crimping Dies ：D-P) （Note）The gap between body and ferule is within 0.5. Body Crimping Dies :D-P 4 2. Cut the cable as fig.2. （Note）Please be careful to not damage the center conductor and outer conductor. 2-1. Pre-solder the center conductor. 0.5 max. Ferrule 1∼1.5 （gap between dies and body） Soldering 5 1∼1.5 （gap between dies and body） 5 5. Solder up the contact with center conductor. Contact Soldering Contact Blind Screw 6 Washer 6. Insert the gasket, washer and blind screw. And screw up the blind screw. Screw toque・・・9.8 〜 19.6N・cm （1 〜 2Kgf・cm） Gasket 6 Blind Screw Washer Gasket ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 16