WT2, NT2, AT2 Series

 METALLIZED POLYPHENYLENE SULFIDE CAPACITORS
POLYOLEFIN ENCASED
METALLIZED POLYPHENYLENE SULFIDE





Self-healing, high reliability
High stability
Low capacitance change over wide temperature range
High volumetric efficiency
Precision circuits requiring low losses, light duty, low frequency
energy discharge, coupling and decoupling
STYLE “T2”




Polyolefin encased, with epoxy end seals
Rectangular axial leads
Not susceptible to burns and punctures characteristic of polyester tape wrap
This capacitor style is intended for utilization in sealed or encapsulated assemblies
Metallized Polyphenylene Sulfide capacitors are also available in many non-metal case styles as well as
hermetically sealed types. Please contact factory or representative.
SPECIFICATIONS
CONSTRUCTION: metallized Polyphenylene sulfide capacitors are available only in extended foil (non-inductive)
construction
PACKAGING: rectangular style, polyolefin encased, with epoxy end seals, axial leads
LEADS: tin or tin/lead plated copper wire is standard and may be soldered or welded in circuit assembly
TEMPERATURE RANGE: may be operated at rated DC voltage from -55°C to 125°C without derating voltage
ELECTRICAL (NON-DESTRUCTIVE) TEST
1.
2.
3.
4.
5.
CAPACITANCE: shall be measured at or referred to 1000 ± 20 Hz at 25 ± 5°C for capacitance values up to
and including 1.0 uf. Capacitance values greater than 1.0 mfd shall be measured at 60 ± 6 Hz.
Ref: MIL-STD-202E, Method 305
DISSIPATION FACTOR: shall be measured as described for capacitance and shall not exceed 0.3% to 1
mfd, 0.5% greater than 1 mfd. Typical values throughout the temperature range, are given on curves.
INSULATION RESISTANCE: shall be measured as follows:
50-100V at 25°C 25,000 meg/mfd, need not exceed 50,000 Megohms
200V + at 25°C 50,000 meg/mfd, need not exceed 100,000 Megohms
Ref: MIL-STD-202E, Method 302
DIELECTRIC STRENGTH: capacitors shall withstand specified DC test potential for one minute through a
limiting resistance of 1 ohm/volt
Terminal to Terminal -- 150 % of DC rating
Terminal to Case -- 200% of DC rating
Ref: MIL-STD-202E, Method 301
DIELECTRIC ABSORPTION: shall not exceed 0.2% when tested to MIL-C-19978D
Ref: MIL-C-19978D, Paragraph 3.22
Electromagnetic Integrated Solutions
8061 Avonia Road ● Fairview ● Pennsylvania ● 16415
Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com
ENVIRONMENTAL TESTS
1.
2.
3.
4.
VIBRATION: capacitors will meet or exceed the requirements of MIL-STD-202E, Method 204
MOISTURE RESISTANCE: capacitors will meet or exceed the requirements of MIL-STD-202E, Method
103B, condition B with 500 VDC or rated voltage applied, whichever is less
LIFE TEST: will withstand 140% of the rated DC voltage at 125°C for 250 hours with not more than one
failure in 12 units
LEAD PULL TEST: the leads on these capacitors shall withstand a steadily applied axial pull of 5 lbs. for
one minute
CUSTOM DESIGN
Available on short notice -- special shapes, values, characteristics, combination sections and networks. Non-metallic
cases or fabricated steel and brass with glass-to-metal seals. Engineering service is expert and prompt.
APPLICATIONS




Metallized Polyphenylene Sulfide capacitors in Style "T2" are encased in irradiated polyolefin and sealed with
epoxy. The polyolefin material is not susceptible to burns that might be inflicted by careless use of a soldering
iron. These capacitors are intended for utilization in sealed or encapsulated assemblies.
Metallized Polyphenylene Sulfide capacitors combine the reliability of self-healing action with high dielectric
strength and insulation resistance of polycarbonate film.
Metallized Polyphenylene Sulfide capacitors are designed primarily for DC application -- blocking, coupling,
decoupling, bypass, DC line filtering - where RF and audio components are small in comparison to DC rating.
However, they have been used very successfully in such AC power applications as power factor correction and
AC line filtering.
Metallized Polyphenylene Sulfide capacitors operate at all temperatures from -55°C to + 125°C.
APPLICATION GUIDE: [AC VOLTAGE RATING, -55˚C to +125˚C. AMBIENT]
EQUIVALENT VAC [RMS] RATING AT
VOLTAGE RATING
60 Hz
400 Hz
50V
N/A
N/A
100V
63 VAC
45 VAC
200V
160 VAC
95 VAC
400V
200 VAC
170 VAC
600V
240 VAC
190 VAC
(AC voltage assumed to be pure sine wave)
TYPICAL TEMPERATURE CHARACTERISTICS
WT2, NT2, AT2 SERIES – SPECIFICATIONS
Electromagnetic Integrated Solutions
8061 Avonia Road ● Fairview ● Pennsylvania ● 16415
Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com
1000 Hz
N/A
40 VAC
80 VAC
140 VAC
160 VAC
DIMENSIONS
*50 VDC
**50 – 100 VDC
**50 – 200 VDC
400 VDC
600 VDC
MFD
T
H
L
Part No.
T
H
L
Part No.
T
H
L
Part No.
T
H
L
Part No.
T
H
L
Part No.
.0010
.0012
.0015
.0018
.0022
.0027
.0033
.0039
.0047
.0056
.0068
.0082
.010
.012
.015
.018
.022
.027
.033
.039
.047
.056
.068
.082
.10
.12
.15
.18
.22
.27
.33
.39
.47
.56
.68
.82
1.0
1.5
2.0
3.0
4.0
5.0
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.09
.10
.10
.12.
.09
.10
12
.14
.15
.16
.19
.21
.24
.21
.23
.27
.33
.33
.30
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.19
.20
.20
.22
.19
.20
.22
.24
.25
.27
.30
.31
.34
.31
.33
.37
.43
.43
.43
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.53
.53
.53
.53
.53
.53
.53
.53
.53
.65
.78
.78
.78
.90
1.17
WT2A102
WT2A122
WT2A152
WT2A182
WT2A222
WT2A272
WT2A332
WT2A392
WT2A472
WT2A562
WT2A682
WT2A822
WT2A103
WT2A123
WT2A153
WT2A183
WT2A223
WT2A273
WT2A333
WT2A393
WT2A473
WT2A563
WT2A683
WT2A823
WT2A104
WT2A124
WT2A154
WT2A184
WT2A224
WT2A274
WT2A334
WT2A394
WT2A474
WT2A564
WT2A684
WT2A824
WT2A105
WT2A155
WT2A205
WT2A305
WT2A405
WT2A505
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.11
.12
.10
.10
.11
.12
.14
.17
.18
.20
.16
.17
.20
.21
.23
.25
.27
.27
.27
.32
.40
.45
.51
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.21
.22
.20
.20
.21
.23
.25
.27
.28
.30
.25
.25
.30
.30
.32
.34
.36
.37
.37
.42
.50
.65
.70
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.53
.53
.53
.53
.53
.53
.53
.53
.65
.65
.65
.78
.78
.78
.78
.90
1.17
1.17
1.17
1.40
1.40
NT2B102
NT2B122
NT2B152
NT2B182
NT2B222
NT2B272
NT2B332
NT2B392
NT2B472
NT2B562
NT2B682
NT2B822
NT2B103
NT2B123
NT2B153
NT2B183
NT2B223
NT2B273
NT2B333
NT2B393
NT2B473
NT2B563
NT2B683
NT2B823
NT2B104
NT2B124
NT2B154
NT2B184
NT2B224
NT2B274
NT2B334
NT2B394
NT2B474
NT2B564
NT2B684
NT2B824
NT2B105
NT2B155
NT2B205
NT2B305
NT2B405
NT2B505
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.10
.12
.14
.10
.11
.12
.14
.15
.16
.18
.20
.22
.19
.21
.24
.19
.21
.24
.27
.30
.33
.32
.34
.43
.43
.49
.55
.60
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.20
.22
.22
.23
.20
.20
.21
.22
.24
.26
.29
.32
.33
.29
.32
.34
.32
.34
.36
.38
.43
.47
.46
.47
.58
.58
.61
.70
.75
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.40
.53
.53
.53
.53
.53
.53
.53
.53
.53
.65
.65
.65
.90
.90
.90
.90
.90
.90
1.17
1.17
1.17
1.40
1.68
1.95
1.95
AT2C102
AT2C122
AT2C152
AT2C182
AT2C222
AT2C272
AT2C332
AT2C392
AT2C472
AT2C562
AT2C682
AT2C822
AT2C103
AT2C123
AT2C153
AT2C183
AT2C223
AT2C273
AT2C333
AT2C393
AT2C473
AT2C563
AT2C683
AT2C823
AT2C104
AT2C124
AT2C154
AT2C184
AT2C224
AT2C274
AT2C334
AT2C394
AT2C474
AT2C564
AT2C684
AT2C824
AT2C105
AT2C155
AT2C205
AT2C305
AT2C405
AT2C505
.10
.10
.10
.10
.10
.10
.12
.13
.10
.10
.10
.11
.12
.14
.16
.18
.20
.23
.19
.21
.23
.21
.24
.26
.29
.33
.30
.33
.31
.35
.39
.43
.48
.38
.43
.48
.54
.62
.73
.92
1.05
1.18
.20
.20
.20
.20
.20
.20
.22
.23
.20
.20
.20
.21
.22
.23
.24
.26
.27
.31
.27
.29
.31
.30
.32
.34
.40
.42
.45
.48
.45
.50
.52
.56
.64
.59
.64
.69
.75
.82
.91
1.15
1.28
1.40
.40
.40
.40
.40
.40
.40
.40
.40
.53
.53
.53
.53
.53
.53
.53
.53
.53
.53
.65
.65
.65
.78
.78
.78
.78
.78
.90
.90
1.17
1.17
1.17
1.17
1.17
1.68
1.68
1.68
1.68
2.00
2.00
2.00
2.25
2.25
AT2E102
AT2E122
AT2E152
AT2E182
AT2E222
AT2E272
AT2E332
AT2E392
AT2E472
AT2E562
AT2E682
AT2E822
AT2E103
AT2E123
AT2E153
AT2E183
AT2E223
AT2E273
AT2E333
AT2E393
AT2E473
AT2E563
AT2E683
AT2E823
AT2E104
AT2E124
AT2E154
AT2E184
AT2E224
AT2E274
AT2E334
AT2E394
AT2E474
AT2E564
AT2E684
AT2E824
AT2E105
AT2E155
AT2E205
AT2E305
AT2E405
AT2E505
.10
.10
.10
.10
.10
.12
.14
.10
.11
.13
.14
.15
.17
.19
.21
.23
.21
.22
.22
.29
.27
.29
.33
.34
.33
.31
.34
.39
.43
.39
.42
.44
.49
.56
.58
.58
.65
.20
.20
.20
.20
.20
.23
.24
.20
.21
.21
.25
.26
.27
.29
.31
.33
.31
.35
.32
.33
.37
.39
.42
.52
.49
.45
.52
.55
.60
.52
.56
.59
.65
.69
.70
.79
.86
.40
.40
.40
.40
.40
.40
.40
.53
.53
.53
.53
.53
.53
.53
.53
.53
.65
.65
.78
.78
.78
.78
.78
.78
.90
1.17
1.17
1.17
1.17
1.68
1.68
1.68
1.68
1.68
2.00
2.25
2.25
AT2G102
AT2G122
AT2G152
AT2G182
AT2G222
AT2G272
AT2G332
AT2G392
AT2G472
AT2G562
AT2G682
AT2G822
AT2G103
AT2G123
AT2G153
AT2G183
AT2G223
AT2G273
AT2G333
AT2G393
AT2G473
AT2G563
AT2G683
AT2G823
AT2G104
AT2G124
AT2G154
AT2G184
AT2G224
AT2G274
AT2G334
AT2G394
AT2G474
AT2G564
AT2G684
AT2G824
AT2G105
Higher values or voltages are available.
*50 VDC units also available in A and N material.
**100 VDC units also available in A material. CASE DIA.
.40 THRU .65
.78 THRU .90
1.17 THRU 2.25
WIRE LEADS
A.W.G.
#24
#22
#20
Electromagnetic Integrated Solutions
8061 Avonia Road ● Fairview ● Pennsylvania ● 16415
Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com
DIA.
.020
.025
.032