Open Frame (Suffix “O”) PSPWX150 SERIES Up to 150 Watts, AC/DC Switching Power Supplies Rev A Wall Industries, Inc. FEATURES • • • • • • RoHS Compliant Dual to Quad Outputs High Efficiency up to 80% 120 Watts with Convection Cooling 150 Watts with Forced Air Cooling 90~264 VAC Input Voltage Range • • • • Built-in Active PFC Function, PF > 0.9 at 230VAC Short Circuit, Over Load, and Over Temperature Protection MTBF > 100,000 Hours UL60950-1, CSA 22.2 No.60950-1, Nemko EN60950-1, & CB IEC60950-1 Safety Approvals • Open Frame and U-Chassis Mechanical Options Available Size: 5.00 x 3.00 x 1.36 inches U-Chassis (Suffix “U”) Size: 5.00 x 3.17 x 1.57 inches DESCRIPTION The PSPWX150 series of AC/DC switching power supplies provides 120 Watts of output power with convection cooling and 150 Watts with 30CFM forced air. This series consists of dual, triple, and quad output models with a 90264VAC input voltage range. These supplies also feature a high efficiency up to 80% and a power factor > 0.9 at 230VAC. These supplies are also protected against short circuit, over load, and over temperature conditions. The PSPWX150 series has UL60950-1, CSA 22.2 No.60950-1, Nemko EN60950-1, and CB IEC60950-1 safety approvals. This series is also CE marked and meets EN55022 Class B, CISPR22 Class B, and FCC Part 15 Class B EMC standards. Both open frame and U-chassis mechanical options are available for this series. SPECIFICATIONS: PSPWX150 SERIES All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION TEST CONDITIONS Min INPUT SPECIFICATIONS Input Voltage Range Input Frequency Input Current (rms) Inrush Current Power Factor Correction 90 47 115VAC and full load 230VAC and full load 115VAC, cold start, 25°C 115VAC, cold start, 25°C 115VAC and full load 230VAC and full load Output Current Minimum Load Hold-up Time PROTECTION Short Circuit Protection Over Load Protection Over Temperature Protection GENERAL SPECIFICATIONS Efficiency ENVIRONMENTAL SPECIFICATIONS Operating Temperature Storage Temperature Range Humidity MTBF PHYSICAL SPECIFICATIONS Weight Dimensions (L x W x H) SAFETY & EMC Safety Approvals EMC Standards 07/30/2013 Measured at 20MHz limited bandwidth and with 0.1μF ceramic and 10μF electrolytic capacitors in parallel across the output 115VAC and full load 16 Auto-recovery Auto-recover; the temperature sensing point is located at HS1 110 84 264 63 2.5 1.25 40 80 VAC Hz A A W See Table 115VAC and full load Derating linearly 2.5% per °C from +41°C to +60°C Unit See Table See Table 120 150 See Table See Table Convection cooling With 30CFM forced air Ripple & Noise Max 0.95 0.90 OUTPUT SPECIFICATIONS Output Voltage Total Regulation Output Power Typ ms Automatic recovery 160 88 92 % °C 80 Non-condensing Full load, 25°C ambient temperature 0 -40 5 100,000 +60 +85 95 °C °C % hours Open Frame Models (Suffix “O”) U-Chassis Models (Suffix “U”) Open Frame Models (Suffix “O”) U-Chassis Models (Suffix “U”) 0.86 lbs (390g) 1.11 lbs (500g) 5.00 x 3.00 x 1.36 in (127 x 76.2 x 34.5 mm) 5.00 x 3.17 x 1.57 in (127 x 80.5 x 40.0 mm) UL60950-1, CSA 22.2 No.60950-1, Nemko EN60950-1, CB IEC60950-1 EN55022 Class B, CISPR22 Class B, FCC Part 15 Class B, CE Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 1 of 5 Wall Industries, Inc. Rev A PSPWX150 SERIES Up to 150 Watts, AC/DC Switching Power Supplies MODEL SELECTION TABLE DUAL OUTPUT MODELS Input Voltage Model Number (1) V2 90~264 VAC V1 V2 PSPW150B-2Y02-X 90~264 VAC V1 V2 PSPW150B-2Y03-X 90~264 VAC V1 PSPW150B-2Y01-X Output Voltage +12 VDC +24 VDC +5 VDC +24 VDC +5 VDC +12 VDC Convection (3) 30CFM Forced Air (3) Minimum Combined Combined Load Max Load Max Power Max Load Max Power Load Max. Load Max. 0.15A 6A 7.5A 120W 150W 0.15A 3.5A 4.5A 0A 10A 12A 120W 150W 0.15A 3.5A 4.5A 0A 10A 12A 120W 150W 0.15A 6A 7.5A Total Regulation Ripple & Noise (2) ±5% ±5% ±5% ±5% ±5% ±5% 120mVp-p 240mVp-p 50mVp-p 240mVp-p 50mVp-p 120mVp-p Total Regulation Ripple & Noise (2) ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% 50mVp-p 120mVp-p 240mVp-p 50mVp-p 50mVp-p 120mVp-p 50mVp-p 50mVp-p 240mVp-p Total Regulation Ripple & Noise (2) ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% 50mVp-p 50mVp-p 120mVp-p 240mVp-p 50mVp-p 50mVp-p 120mVp-p 120mVp-p 50mVp-p 50mVp-p 150mVp-p 150mVp-p 50mVp-p 50mVp-p 120mVp-p 480mVp-p 50mVp-p 120mVp-p 240mVp-p 120mVp-p 50mVp-p 120mVp-p 240mVp-p 150mVp-p 50mVp-p 50mVp-p 120mVp-p 280mVp-p TRIPLE OUTPUT MODELS Input Voltage Model Number (1) V3 PSPW150B-3Y01-X V2 90~264 VAC V1 V3 PSPW150B-3Y02-X V2 90~264 VAC V1 V3 PSPW150B-3Y03-X V2 90~264 VAC V1 Output Voltage +5 VDC +12 VDC +24 VDC +3.3 VDC +5 VDC +12 VDC +3.3 VDC +5 VDC +24 VDC Convection (3) 30CFM Forced Air (3) Minimum Combined Combined Load Max Load Max Power Max Load Max Power Load Max. Load Max. 0A 10A 12A 75W 90W 120W 150W 0.15A 6A 7.5A 0.15A 3.5A 4.5A 0A 10A 12A 75W 90W 120W 150W 0A 10A 12A 0.15A 6A 7.5A 0A 10A 12A 75W 90W 120W 150W 0A 10A 12A 0.15A 3.5A 4.5A QUAD OUTPUT MODELS Input Voltage Model Number (1) PSPW150B-4Y01-X PSPW150B-4Y02-X PSPW150B-4Y03-X PSPW150B-4Y04-X PSPW150B-4Y05-X PSPW150B-4Y06-X PSPW150B-4Y07-X V4 V3 V2 V1 V4 V3 V2 V1 V4 V3 V2 V1 V4 V3 V2 V1 V4 V3 V2 V1 V4 V3 V2 V1 V4 V3 V2 V1 90~264 VAC 90~264 VAC 90~264 VAC 90~264 VAC 90~264 VAC 90~264 VAC 90~264 VAC Output Voltage +3.3 VDC +5 VDC +12 VDC +24 VDC +3.3 VDC +5 VDC +12 VDC -12 VDC +3.3 VDC +5 VDC +15 VDC -15 VDC +3.3 VDC +5 VDC +12 VDC +48 VDC +5 VDC +12 VDC +24 VDC -12 VDC +5 VDC +12 VDC +24 VDC -15 VDC +3.3 VDC +5 VDC +12 VDC +28 VDC Convection (3) 30CFM Forced Air (3) Minimum Combined Combined Load Max Load Max Power Max Load Max Power Load Max. Load Max. 0A 10A 12A 75W 90W 0A 10A 12A 120W 150W 0.15A 6A 7.5A 0.15A 3.5A 4.5A 0A 10A 12A 105W 125W 0A 10A 12A 120W 150W 0.15A 6A 7.5A 0.15A 1.5A 2.5A 0A 10A 12A 105W 125W 0A 10A 12A 120W 150W 0.15A 2.5A 3.5A 0.15A 1.25A 1.75A 0A 10A 12A 105W 125W 0A 10A 12A 120W 150W 0.15A 6A 7.5A 0.15A 0.5A 1.0A 0A 10A 12A 75W 90W 0.15A 6A 7.5A 120W 150W 0.15A 3.5A 4.5A 0.15A 1.5A 1.5A 0A 10A 12A 75W 90W 0.15A 6A 7.5A 120W 150W 0.15A 3.5A 4.5A 0.15A 1.5A 1.0A 0A 10A 12A 75W 90W 0A 10A 12A 120W 150W 0.15A 6A 7.5A 0.15A 3A 4.0A NOTES 1. 2. 3. 4. The “X” in the model number can be “O” for open frame type or “U” for U-chassis type. Measured at 20MHz limited bandwidth and with 0.1μF ceramic and 10μF electrolytic capacitors in parallel across the output. 120W max. with convection cooling and 150W max. with 30CFM minimum forced airflow. These supplies require a minimum load on the output to maintain specified regulations. Operation under no-load conditions will not damage these devices; however, they may not meet all listed specifications. 07/30/2013 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 2 of 5 PSPWX150 SERIES Up to 150 Watts, AC/DC Switching Power Supplies Rev A Wall Industries, Inc. MECHANICAL DRAWING OPEN FRAME MODELS (SUFFIX “O”) Unit: inches (mm) 5.00 (127.0) OUTPUT CONNECTOR CONFIGURATION 4.57 (116.0) 0.22 (5.5) 0.22 (5.5) 0.22 (5.5) PSPW-150B-2Y01-O PSPW-150B-2Y02-O PSPW-150B-2Y03-O 1 2 CN2 3 2 2.57 (65.2) 3.00 (76.2) 4 5 6 7 5 8 6 9 10 7 11 10 L 11 CN1 0.22 (5.5) N PSPW-150B-3Y01-O OTHERS 0.09 (2.2) 1.36 (34.5) 4 X Ø0.138 (Ø3.5) mounting holes 1 3 11 11 CN1: INPUT CONNECTOR JST B3P-VH-B pitch: 7.92mm or equivalent, mates with JST VHR-3N or equivalent PIN 1 2 CN1: INPUT CONNECTOR FUNCTION AC (L) AC (N) 07/30/2013 CN2: OUTPUT CONNECTOR JST B11P-VH-B pitch: 3.96mm or equivalent, mates with JST VHR-11N or equivalent CN2: OUTPUT CONNECTOR PIN MODEL PSPW-150B-2Y01-O PSPW-150B-2Y02-O PSPW-150B-2Y03-O PSPW-150B-3Y01-O PSPW-150B-3Y02-O PSPW-150B-3Y03-O PSPW-150B-4Y01-O PSPW-150B-4Y02-O PSPW-150B-4Y03-O PSPW-150B-4Y04-O PSPW-150B-4Y05-O PSPW-150B-4Y06-O PSPW-150B-4Y07-O 1 2 3 4 5 6 7 8 9 10 11 +3.3V +3.3V +3.3V +3.3V +3.3V +3.3V -12V -15V +3.3V +24V +3.3V +3.3V +3.3V +3.3V +3.3V +3.3V -12V -15V +3.3V GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND +12V +12V +12V +12V +12V +12V +15V +12V +12V +12V +12V +12V +12V +12V +12V +12V +12V +15V +12V +12V +12V +12V +24V +24V +24V +24V -12V -15V +48V +24V +24V +28V Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 3 of 5 PSPWX150 SERIES Up to 150 Watts, AC/DC Switching Power Supplies Rev A Wall Industries, Inc. MECHANICAL DRAWING U-CHASSIS MODELS (SUFFIX “U”) Unit: inches (mm) 5.00 (127.0) OUTPUT CONNECTOR CONFIGURATION PSPW-150B-2Y01-U PSPW-150B-2Y02-U PSPW-150B-2Y03-U 2 0.30 (7.5) 0.30 (7.5) 0.20 (5.0) 5 0.20 (5.0) 6 7 4.57 (116.0) 0.22 (5.5) 0.22 (5.5) 0.30 (7.65) 10 11 1 2 4 5 6 7 8 9 2.57 (65.2) 3.17 (80.5) CN2 3 PSPW-150B-3Y01-U OTHERS 10 11 L 1 CN1 0.30 (7.65) N 3 4 X M3 PEM Nuts on the opposite side of U-bracket for mounting 0.20 (5.0) 4 X M3 screw mounting holes 0.20 (5.0) 0.30 (7.5) 11 11 1.57 (40.0) 0.30 (7.5) CN1: INPUT CONNECTOR JST B3P-VH-B pitch: 7.92mm or equivalent, mates with JST VHR-3N or equivalent PIN 1 2 CN1: INPUT CONNECTOR FUNCTION AC (L) AC (N) 07/30/2013 CN2: OUTPUT CONNECTOR JST B11P-VH-B pitch: 3.96mm or equivalent, mates with JST VHR-11N or equivalent CN2: OUTPUT CONNECTOR PIN MODEL PSPW-150B-2Y01-U PSPW-150B-2Y02-U PSPW-150B-2Y03-U PSPW-150B-3Y01-U PSPW-150B-3Y02-U PSPW-150B-3Y03-U PSPW-150B-4Y01-U PSPW-150B-4Y02-U PSPW-150B-4Y03-U PSPW-150B-4Y04-U PSPW-150B-4Y05-U PSPW-150B-4Y06-U PSPW-150B-4Y07-U 1 2 3 4 5 6 7 8 9 10 11 +3.3V +3.3V +3.3V +3.3V +3.3V +3.3V -12V -15V +3.3V +24V +3.3V +3.3V +3.3V +3.3V +3.3V +3.3V -12V -15V +3.3V GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND +12V +12V +12V +12V +12V +12V +15V +12V +12V +12V +12V +12V +12V +12V +12V +12V +12V +15V +12V +12V +12V +12V +24V +24V +24V +24V -12V -15V +48V +24V +24V +28V Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 4 of 5 PSPWX150 SERIES Up to 150 Watts, AC/DC Switching Power Supplies Rev A Wall Industries, Inc. DERATING CURVE 120 Output Power (%) 100 80 60 40 20 0 -40 0 10 20 30 40 50 60 70 80 Ambient Temperature (°C) COMPANY INFORMATION Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development engineers will provide a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008 certification is just one example of our commitment to producing a high quality, well-documented product for our customers. Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your future projects. Contact Wall Industries for further information: Phone: Toll Free: Fax: E-mail: Web: Address: 07/30/2013 (603)778-2300 (888)597-9255 (603)778-9797 [email protected] www.wallindustries.com 37 Industrial Drive Exeter, NH 03833 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 5 of 5