PSIM65B2 SERIES 40~65 Watts AC DC Open Frame Power Supplies Single Outputs Rev A FEATURES • • • • Both ITE & Medical Approvals Medical Body Floating (BF) Rated Class I Power Supply Altitude During Operation: ITE up to 5000m, Medical Below 3000m • Low Leakage Current • Wide Input Voltage Range of 90~264VAC • Output Voltage Ranging from 5-54V • Medical Applications Protection: Means of Patient Protection (MOPP) • Short Circuit, Over Load, and Over Voltage Protection • High Efficiency >89% (Except 5V models which are >86%) • Meets Efficiency Level VI • UL60601-1, EN60601-1, and IEC EN60601-1 3rd Edition Safety Approvals, among others DESCRIPTION Size: 4in x 2in x 1.08in (101.6mm x 50.8mm x 27.5mm) The PSIM65B2 series of AC DC open frame power supplies provides up to 65 watts of output power in a 4” x 2” x 1.08” frame. This series consists of single output models that have a wide input voltage range of 90~264VAC and output voltages ranging from 5V to 54V. These models have a low leakage current and high efficiency greater than 89%.They are also Efficiency Level VI and RoHS compliant. Each model is protected against short circuit, over load, and over voltage conditions, and also has means of patient protection (MOPP). Different input and output connectors are available, please call factory for ordering details. MODEL SELECTION TABLE Model Number(1) Input Voltage Range Output Voltage(2) Output Current Min Load Max Load 0A 8.00A PSIM040B2-1Y050Z 5V PSIM065B2-1Y120Z 12V 0A PSIM065B2-1Y150Z 15V 0A PSIM065B2-1Y190Z 19V 0A 24V 0A PSIM065B2-1Y240Z 90~264VAC 5.42A Ripple & Noise(3) Output Regulation Output Power Efficiency Full Load <30% Load 100mV 200mV ±5% 40W >86% 120mV 200mV ±3% 65W >89% 4.34A 120mV 300mV ±3% 65W >89% 3.43A 120mV 300mV ±3% 65W >89% 2.71A 200mV 300mV ±3% 65W >89% >89% PSIM065B2-1Y280Z 28V 0A 2.33A 200mV 350mV ±3% 65W PSIM065B2-1Y480Z 48V 0A 1.36A 200mV 480mV ±2% 65W >89% PSIM065B2-1Y540Z 54V 0A 1.21A 200mV 480mV ±2% 65W >89% 2/22/2016 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 1 of 4 PSIM65B2 SERIES 40~65 Watts AC DC Open Frame Power Supplies Single Outputs Rev A SPECIFICATIONS All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION TEST CONDITIONS INPUT SPECIFICATIONS Input Voltage Range Input Frequency Min Typ 90 47 @115VAC, Cold Start @25ºC @230VAC, Cold Start @25ºC @115VAC @230VAC @264VAC Inrush Current Input Current (rms) Touch Current OUTPUT SPECIFICATIONS Output Voltage Output Power Output Current Minimum Load Ripple & Noise (20MHz bandwidth) Hold-Up Time @Full Load, 115VAC PROTECTION Short Circuit Protection Over Load Protection Maximum Rating, Auto-Recovery Over Voltage Protection Latching Type ENVIRONMENTAL SPECIFICATIONS Derate linearly 2.5% per ºC from 51 to 70ºC Operating Temperature Derate linearly 1.0% per ºC from 0 to -20ºC Storage Temperature Humidity Non Condensing Cooling MTBF @Full Load and 25ºC ambient temperature GENERAL SPECIFICATIONS Efficiency @full load, 115VAC (5V series excluded) No Load Power Consumption PHYSICAL SPECIFICATIONS Weight Dimensions (L x W x H) Max Unit 264 63 45 90 2 1 100 VAC Hz A A uA See Table See Table See Table 0 A See Table 10 110 mS Automatic Recovery 180 AC Recycle % -20 70 ºC -20 10 85 90 Convection ºC % 150,000 hours >87 75 % mW 4.8oz (136g) 4in x 2in x 1.08in (101.6mm x 50.8mm x 27.5mm) SAFETY & EMC CHARACTERISTICS UL 60601-1 3rd Edition UL/c-UL UL60950-1 EN60601-1 3rd Edition TUV EN60950-1 IEC EN60601-1 3rd Edition CB IEC 60950-1 EN60601-1-2 Safety Approvals EMC Standards EN55024 EN 55011 EN 55022 FCC Part 15 FCC Part 18 CE Class B Class B Class B Class B NOTES (1) (2) (3) 2/22/2016 Z indicates In/Output connector options: “Z”= J (JST VH Type Connector or Equ.), Z=M (Molex 5277 Type Connector or Equ.) Output Voltage is set my manufacturer Ripple and nose are measured at oscilloscope 20MHz bandwidth by a 10uF electrolytic capacitor and a 0.1uF ceramic capacitor in parallel at output connector. Ripple and noise will be higher while load is under 30% of rate load during Burst Mode operation. Burst Mode operation is to meet the latest efficiency regulations. Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 2 of 4 Rev A PSIM65B2 SERIES 40~65 Watts AC DC Open Frame Power Supplies Single Outputs MECHANICAL DRAWINGS Mechanical Specification In/Output Connector: J (JST) 2/22/2016 In/Output Connector: M (Molex) Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 3 of 4 PSIM65B2 SERIES 40~65 Watts AC DC Open Frame Power Supplies Single Outputs Rev A MATCHING CONNECTORS CN1: Input Connector JST B3P-VH-B pitch: 3.96mm or equivalent Mates with JST VHR-3N or equivalent Pin # Signal 1 AC Neutral 2 AC Line MOLEX 5277 09-65-2029 or equivalent Mates with MOLEX 5265 09-76-1020 or equivalent Pin # Signal 1 AC Line 2 AC Neutral CN2: Main Output Connector JST B4P-VH-B pitch: 3.96mm or equivalent Mates with JST VHR-4N or equivalent Pin # Signal 1 GND 2 GND 3 +Vo 4 +Vo MOLEX 5277 09-65-2048 or equivalent Mates with MOLEX 5239 09-52-4044 or equivalent Pin # Signal 1 +Vo 2 +Vo 3 GND 4 GND CN3: Remote Sense Connector JST B2B-XH-A pitch: 2.5mm or equivalent Mates with JST XHP-2 or equivalent Pin # Signal 1 +Vo Sense + 2 +Vo Sense - COMPANY INFORMATION Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development engineers will provide a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008 certification is just one example of our commitment to producing a high quality, well-documented product for our customers. Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your future projects. Contact Wall Industries for further information: Phone: Toll Free: Fax: E-mail: Web: Address: 2/22/2016 (603)778-2300 (888)597-9255 (603)778-9797 [email protected] www.wallindustries.com 37 Industrial Drive Exeter, NH 03833 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 4 of 4