PSRL5017R6 SERIES Up to 600 Watts Single Output with Active PFC AC/DC Switching Power Supply Rev B Size: 9.2in x 4.3in x 2.5in FEATURES • • • • Optional Top Cover Available Universal AC Input/Full Range Optional N+1 Active Current Sharing Peak Power 900W within 500µS duty duration • • • • Power Factor Corrected to EN61000-3-2 Class D High Power Density (Max. 9.1 Watts per cubic inch) Approved to UL/CUL/TUV/CB/CE & Class B Emissions Enclosed with Built-in Fan Mechanical Options DESCRIPTION The PSRL5017R6 series of AC DC power supplies provides up to 500W of output power. All models have a single output and a universal input voltage range. Models are available as enclosed with built-in Fan (Type E). Output connectors are Howder terminal block design. Optional Mating Molex outputs are also available. Please contact factory for ordering details. MODEL SELECTION TABLE Model Number PSRL5017Rx6-03(I) PSRL5017Rx6-05(I) PSRL5017Rx6-12(I) PSRL5017Rx6-16(I) PSRL5017Rx6-24(I) PSRL5017Rx6-36(I) PSRL5017Rx6-48(I) 12/11/2015 Output Voltage Range Output Current Ripple & Noise Preset Voltage Output Power Regulation 2-3.3VDC 5-6VDC 12-15VDC 16-21VDC 22-30VDC 31-47VDC 48-56VDC 90A 90A 50A 37.5A 27.27A 19.35A 12.5A 75mV 75mV ±1% ±1% ±1% ±1% ±1% 3.3VDC 5VDC 12VDC 18VDC 24VDC 36VDC 48VDC 297W 450W 600W 600W 600W 600W 600W ±1% ±1% ±1% ±1% ±1% ±1% ±1% Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 1 of 4 PSRL5017R6 SERIES Up to 600 Watts Single Output with Active PFC AC/DC Switching Power Supply Rev B SPECIFICATIONS: PSRL5017R6 All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION TEST CONDITIONS Min Typ Max Unit 90 264 VAC 47 63 Hz 70 A 3.5 mA INPUT SPECIFICATIONS Input Voltage Range Full Range (PSRL5017Rx8 800W Series: 180-264VAC only) Input Frequency Inrush Current @230VAC with Full Load Cold Start Leakage Current @240VAC Input Current Remote ON/OFF OUTPUT SPECIFICATIONS Output Voltage Output Power Range Output Adjustability Total Regulation Output Current Ripple and Noise (peak to peak) @90VAC and Full Load Designated as RSW on CN3, requires a low signal to inhibit output Hold-Up Time Overshoot Turn On Delay Remote Sense PROTECTION Short Circuit Protection Over-Temperature Protection Over Voltage Protection Over-Power Protection Input Voltage Protection Input Fusing Protection ENVIRONMENTAL SPECIFICATIONS Operating Temperature Storage Temperature Operating Humidity Storage Humidity Vibration Cooling MTBF GENERAL SPECIFICATIONS Withstand Voltage Burn-In PFC Power Good Grounding Test Current Sharing Current Monitor LED Display 12/11/2015 A See Table 600 ±5 ±1 See Table See Table Returns to within 1% in less than 2.5ms for a 50% load change and the peak transient does not excess 5% @80% of Full Load. Turn-On & Off overshoot <5% over normal voltage @120VAC Designated as RS+ and RS- on CN3. Voltage compensates for up to 0.5V line drop. (Not available for current sharing models) Transient Response Efficiency With Airflow. Output user adjustable 10 20 W % % ms 1 Sec. +70 85 90 95 50 °C °C % RH % RH Hz Trip without damage and auto-recovery. Unit protected of excessive operating ambient 85°C and automatic recovery. Unit latching down when output voltage exceeds 130% and recycle AC input to reset. Fold back mode 110-140% and auto-recovery. Power shut down under 80 ±5VAC, and recovered over 86VAC A T10A/250V fuse inserted in primary Ambient, De-Rating at 2.5% per degree from 50°C to 70°C Non-Condensing Non-Condensing Acceleration 7.35 m/(s x s) on X,Y, and Z axis Self-cooled by built-in fan. (according to MIL-HBK-217F) @30°C 3.3V 5V @230VAC and Full Load 12V All other Outputs 1500 VAC input line to chassis (10mA DC cut off current); 3000VAC between primary and secondary windings. Primary to core 1500VAC. All for 3 seconds. For one hour @ 230VAC with Full Load Active power factor correction meets EN61000-3-2 Class D Designated as PG on the CN3 and TTL high 100-500ms after regulation. It goes low at least 1ms before loss of regulation for Power on Reset signal. Apply 25A from ground pin of the three prong plug to the far most earth. Max allowable resistance is 0.1 ohm. Designated as CSH on the CN3, optional single wired for forced current sharing function and parallel up to 4 units within 10% accuracy at full load. Designated as CMN on the CN3 is a 0.5V to 3VDC output voltage to represent 0% to 100% output current. Bi-Color LED1 emit Green for Power On and emit Orange when protection is enabled or RSW is applied to a low signal 0 -20 5 5 5 150,000 Hr 70 75 80 % 83 40 45 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] 50 °C Page 2 of 4 PSRL5017R6 SERIES Up to 600 Watts Single Output with Active PFC AC/DC Switching Power Supply Rev B SPECIFICATIONS All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION TEST CONDITIONS Min Typ Max Unit PHYSICAL SPECIFICATIONS Weight 1450 grams Dimensions (L x W x H) SAFETY & EMC CHARACTERISTICS 9.2in x 4.3in 2.5in UL60950-1 CSA C22.2 No. 60950-1-03 TUV EN60950-1 CE Mark (LVD) EN61000-3-2-3 IEC61000-4 Series Regulations and CB Safety Regulations Emissions FCC part15, CISPR 22 Class B, Conducted NOTES (1) (2) (3) (4) (5) (6) The PSRL5017R6 Series is designated as PSRL5017Rxw-yz where x=E (Enclosed with built-in fan type), w=6 for output power from 264W500W, y= 03,05,12,16,36, or 48 for output voltage, and z can be blank or I where I denotes forced current sharing option (output with internal ORring diode). See PSRL5017R-I Series for forced current sharing. All output ranges are covered in agency certifications and preset voltage will be set as standard models. If any request is not preset output, then please contact us in advance. Ripple & Noise are measured from 10KHZ to 20 MHz bandwidth at output with parallel 0.1µF ceramic and 22µF electrolytic capacitors. Providing peak power to 900W within 500µS for all models, longer duty duration need contact with manufacturer. 1% minimum load is required to maintain the ripple and regulation. Output is fully isolated. MECHANICAL DRAWINGS Enclosed with Built-In Fan Type 12/11/2015 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 3 of 4 PSRL5017R6 SERIES Up to 600 Watts Single Output with Active PFC AC/DC Switching Power Supply Rev B I/O Connector Pin Assignment AC Input Connector (CN1): IEC320 or equivalent Snap-in mounting type or DINKLE Terminal Block Part No. DT-35-A02W-03 (3 pin) Output Connector (CN2): Mating Molex Part No. 09-91-2000 (20 Pin) or Howder Terminal Bloack Part No. HD-121-8P (8 pin) Output Pin Assignment: Output Pin Connetion Howder Molex Vo+ Vo- Pins 1-4 Pins 5-8 Pins 1-10 Pins 11-20 Logic Signal Connectors (CN3): Mating JST XHP-7 or equivalent (CHYAO SHIUNN JS-2001-07). Fan Drive: 12VDC/500mA Mating JST XHP-2 or equivalent (CHYAO SHIUNN JS-2001-02 Mounting Inserts: 6-32, M4 4 Places individually with maximum penetration 0.2 inch on bottom side and 0.25 inch on both sides. COMPANY INFORMATION Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development engineers will provide a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008 certification is just one example of our commitment to producing a high quality, well-documented product for our customers. Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your future projects. Contact Wall Industries for further information: Phone: Toll Free: Fax: E-mail: Web: Address: 12/11/2015 (603)778-2300 (888)597-9255 (603)778-9797 [email protected] www.wallindustries.com 37 Industrial Drive Exeter, NH 03833 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797 website: www.wallindustries.com • e-mail: [email protected] Page 4 of 4