LTC6954 - Low Phase Noise, Triple Output Clock Distribution Divider/Driver

LTC6954
Low Phase Noise,
Triple Output Clock
Distribution Divider/Driver
Description
Features
Low Noise Clock Distribution: Suitable for High
Speed/High Resolution ADC Clocking
n Additive Jitter < 20fs
RMS (12kHz to 20MHz)
n Additive Jitter < 85fs
RMS (10Hz to Nyquist)
n 1.8GHz Maximum Input Frequency
(LTC6954-1 When DELAY = 0)
n 1.4GHz Maximum Input Frequency
(LTC6954-1 When DELAY > 0, LTC6954-2, -3, -4)
n EZSync™ Clock Synchronization Compatible
n Three Independent, Low Noise Outputs
n Four Output Combinations Available
n Three Independent Programmable Dividers Covering
All Integers From 1 to 63
n Three Independent Programmable Delays Covering
All Integers From 0 to 63
n–40°C to 105°C Junction Temperature Range
The LTC®6954 is a family of very low phase noise clock
distribution parts. Each part has three outputs and each
output has an individually programmable frequency
divider and delay. There are four members of the family,
differing in their output logic signal type:
LTC6954-1: Three LVPECL outputs
LTC6954-2: Two LVPECL and one LVDS/CMOS outputs
LTC6954-3: One LVPECL and two LVDS/CMOS outputs
LTC6954-4: Three LVDS/CMOS outputs
n
Each output is individually programmable to divide the
input frequency by any integer from 1 to 63, and to delay
each output by 0 to 63 input clock cycles. The output duty
cycle is always 50%, regardless of the divide number.
The LVDS/CMOS outputs are jumper selectable via the
OUTxSEL pins to provide either an LVDS logic output or
a CMOS logic output.
Applications
The LTC6954 also features Linear Technology’s EZSync
system for perfect clock synchronization and alignment
every time.
Clocking High Speed, High Resolution ADCs, DACs
and Data Acquisition Systems
n Low Jitter Clock Distribution
n
All device settings are controlled through an SPI-compatible
serial port.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and EZSync
is a trademark of Linear Technology Corporation. All other trademarks are the property of their
respective owners. Protected by U.S. Patents, including 8319551, 8819472.
Typical Application
Additive Phase Noise vs Offset Frequency,
fIN = 622.08MHz, Mx[5:0] = 4,
fOUTx = 155.52MHz
3.3V
UP TO 1.4GHz
49.9Ω
V+
IN+
49.9Ω
49.9Ω
SYNC
SYNC
CONTROL
OUT0SEL
3.3V
OUT1SEL
OUT2SEL
SDO
SPI
SERIAL
PORT
SDI
SERIAL
PORT
AND
DIGITAL
DELAY
0 TO 63
–120
LTC6954-3
IN–
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
OUT0+
OUT0–
OUT1+
OUT1–
OUT2+
OUT2–
LVPECL OUTPUT
FREQUENCY
UP TO 1.8GHz
LVDS OUTPUT
FREQUENCY
UP TO 1.4GHz
CMOS OUTPUT
FREQUENCY
UP TO 250MHz
SCLK
CS
ADDITIVE PHASE NOISE (dBc/Hz)
0.1µF
–130
–140
–150
–160
–170
–180
GND
6954 TA01a
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
10M
6954 TA01b
6954f
For more information www.linear.com/LTC6954
1
LTC6954
Absolute Maximum Ratings
Pin Configuration
(Note 1)
OUT2SEL
GND
VA+
OUT1SEL
GND
TEMP
TOP VIEW
36
35
34
33
32
31
VOUT2+ 1
30 VIN+
OUT2–
29 GND
2
OUT2+ 3
28 IN–
+
4
27 IN+
+
5
26 GND
VOUT2
VOUT1
OUT1– 6
25 VIN+
37
GND
OUT1+ 7
24 VA+
VOUT1+ 8
23 VA+
VOUT0+ 9
22 SYNC
OUT0– 10
21 VD+
OUT0+ 11
20 SDI
VOUT0+ 12
17
18
VD+
VA+
16
CS
15
SDO
14
GND
19 SCLK
13
OUT0SEL
Supply Voltages
(VA+, VD+, VIN+, VOUT0+, VOUT1+ and
VOUT2+ to GND).........................................................3.6V
LTC6954-1, -2, -3 LVPECL Outputs
OUTx Output Voltage High.......................VOUT+ + 0.3V
OUTx Output Voltage Low...................... Source 25mA
LTC6954-2, -3, -4 LVDS/CMOS Outputs
OUTx...........................................–0.3V to (VA+ +0.3V)
TEMP Input Current................................................10mA
TEMP Low Voltage .................................................–0.3V
Voltage on All Other Pins............... –0.3V to (VA+ + 0.3V)
Operating Junction Temperature Range, TJ (Note 2)
LTC6954I................................................ –40°C to 105°C
Junction Temperature, TJMAX................................. 150°C
Storage Temperature Range................... –65°C to 150°C
UFF PACKAGE
36-LEAD (4mm × 7mm) PLASTIC QFN
0.5mm LEAD PITCH
TJMAX = 150°C, θJCbottom = 2°C/W, θJCtop = 18°C/W
EXPOSED PAD (PIN 37) IS GND, MUST BE SOLDERED TO PCB GND
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
JUNCTION TEMPERATURE RANGE
LTC6954IUFF-1#PBF
LTC6954IUFF-1#TRPBF
69541
36-Lead (4mm × 7mm) Plastic QFN
–40°C to 105°C
LTC6954IUFF-2#PBF
LTC6954IUFF-2#TRPBF
69542
36-Lead (4mm × 7mm) Plastic QFN
–40°C to 105°C
LTC6954IUFF-3#PBF
LTC6954IUFF-3#TRPBF
69543
36-Lead (4mm × 7mm) Plastic QFN
–40°C to 105°C
LTC6954IUFF-4#PBF
LTC6954IUFF-4#TRPBF
69544
36-Lead (4mm × 7mm) Plastic QFN
–40°C to 105°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
For more information on lead free part markings, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
6954f
2
For more information www.linear.com/LTC6954
LTC6954
Electrical Characteristics
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C. VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V, unless
otherwise specified. All voltages are with respect to GND. (Note 2)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
1800
1400
MHz
MHz
1.5
VP-P
Input (IN+, IN – )
fIN
Input Frequency
LTC6954-1, DELx = 0
LTC6954-1 (DELx > 0), LTC6954-2, -3, -4
l
l
VIN
Input Signal Level
Single-Ended
l
0.2
l
100
Input Slew Rate
DCIN
0.8
V/µs
Input Duty Cycle
50
Self-Bias Voltage
l
1.9
%
2.05
2.2
V
Minimum Common Mode Level
400mVP-P Differential Input
1.8
V
Maximum Common Mode Level
400mVP-P Differential Input
2.3
V
Input Resistance
Differential
Input Capacitance
Differential
l
1.8
2.2
2.7
kΩ
0.5
pF
Output Divider (M)
Mx[5:0]
Divider Range
M0[5:0], M1[5:0], M2[5:0]
All Integers Included
l
1
63
Cycles
DELx[5:0]
Divider Delay in Input Clock Cycles
DEL0[5:0], DEL1[5:0], DEL2[5:0]
All Integers Included
l
0
63
Cycles
LVPECL Clock Outputs
fOUT
Frequency
LTC6954-1, DELx = 0
LTC6954-1 (DELx > 0), LTC6954-2, -3, -4
l
l
|VOD|
Differential Voltage
(Output Static)
Single-Ended Termination = 50Ω to (VOUTx+ – 2V)
l
640
Differential Termination = 100Ω, Internal Bias On
l
640
VCM
Common Mode Voltage
(Output Static)
tRISE
Rise Time, 20% to 80%
tFALL
Fall Time, 80% to 20%
DCLVPECL
Duty Cycle
+ – 2V)
Single-Ended Termination = 50Ω to (VOUTx
l
Differential Termination = 100Ω, Internal Bias On
l
775
780
1800
1400
MHz
MHz
950
mVPK
950
mVPK
+
VOUTx
– 1.67
+
VOUTx
– 1.42
+
VOUTx
– 1.14
V
VOUTx+
– 1.67
VOUTx+
– 1.42
VOUTx+
– 1.14
V
Single-Ended Termination = 50Ω to (VOUTx+ – 2V)
110
ps
Differential Termination = 100Ω, Internal Bias On
110
ps
Single-Ended Termination = 50Ω to (VOUTx+ – 2V)
110
ps
Differential Termination = 100Ω, Internal Bias On
110
ps
Mx[5:0] = 1
DCIN
%
Mx[5:0] > 1 (Even or Odd)
l
45
50
55
%
250
MHz
CMOS Clock Outputs
fOUT
Frequency
l
VOH
High Voltage (Output Static)
2.5mA Load
l
VOL
Low Voltage (Output Static)
2.5mA Load
l
tRISE
Rise Time, 20% to 80%
CLOAD = 2pF, CMSINV = 1
tFALL
Fall Time, 80% to 20%
DCCMOS
Duty Cycle
V+ – 0.4
V
0.4
V
200
ps
CLOAD = 2pF, CMSINV = 1
170
ps
Mx[5:0] = 1
DCIN
%
Mx[5:0] > 1 (Even or Odd)
l
45
50
55
%
6954f
For more information www.linear.com/LTC6954
3
LTC6954
Electrical Characteristics
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C. VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V, unless
otherwise specified. All voltages are with respect to GND. (Note 2)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
LVDS Clock Outputs
fOUT
|VOD|
|ΔVOD|
VOS
Frequency
Differential Voltage
(Output Static)
Delta VOD (Output Static)
Offset Voltage (Output Static)
Differential Termination = 100Ω, 3.5mA Mode
l
800
MHz
Differential Termination = 50Ω, 7mA Mode
l
1400
MHz
Differential Termination = 100Ω, 3.5mA Mode
l
290
370
450
mVPK
Differential Termination = 50Ω, 7mA Mode
l
290
370
450
mVPK
Differential Termination = 100Ω, 3.5mA Mode
l
–30
30
mV
Differential Termination = 50Ω, 7mA Mode
l
–30
30
mV
Differential Termination = 100Ω, 3.5mA Mode
l
1.16
1.23
1.32
Differential Termination = 50Ω, 7mA Mode
l
1.15
1.23
1.32
V
V
|ΔVOS|
Delta VOS (Output Static)
Differential Termination = 100Ω, 3.5mA Mode
l
–15
Differential Termination = 50Ω, 7mA Mode
l
–15
tRISE
Rise Time, 20% to 80%
Differential Termination = 100Ω, 3.5mA Mode
Differential Termination = 50Ω, 7mA Mode
120
ps
tFALL
Fall Time, 80% to 20%
Differential Termination = 100Ω, 3.5mA Mode
240
ps
Differential Termination = 50Ω, 7mA Mode
120
ps
|ISA|, |ISB|
Short-Circuit Current to Common
Shorted to GND, 3.5mA Mode
16
mA
Shorted to GND, 7mA Mode
25
mA
|ISAB|
Short-Circuit Current to
Complementary
3.5mA Mode
4
mA
7mA Mode
8
mA
DCLVDS
Duty Cycle
Mx[5:0] = 1
DCIN
%
15
mV
15
mV
240
ps
Mx[5:0] > 1 (Even or Odd)
l
45
50
55
%
Propagation Delay From IN to
Any LVPECL Output
Mx[5:0] = 1
l
290
360
480
ps
Mx[5:0] > 1
l
360
430
550
ps
Temperature Variation of the
Propagation Delay From IN to
Any LVPECL Output
Mx[5:0] = 1
l
0.65
ps/°C
Mx[5:0] > 1
l
0.68
ps/°C
Propagation Delay From IN to
Any LVDS Output,
LVCSx = 1 (7mA Mode)
Mx[5:0] = 1
l
350
420
545
ps
Mx[5:0] > 1
l
415
480
625
ps
Temperature Variation of the
Propagation Delay From IN to
Any LVDS Output,
LVCSx = 1 (7mA Mode)
Mx[5:0] = 1
l
0.8
ps/°C
Mx[5:0] > 1
l
0.85
ps/°C
Propagation Delay From IN to
Any LVDS Output,
LVCSx = 0 (3.5mA Mode)
Mx[5:0] = 1
480
ps
Mx[5:0] > 1
550
ps
Temperature Variation of the
Propagation Delay From IN to
Any LVDS Output,
LVCSx = 0 (3.5mA Mode)
Mx[5:0] = 1
l
0.8
ps/°C
Mx[5:0] > 1
l
0.85
ps/°C
Output Propagation Delays
tPD(LVPECL)
tpd(LVDS)
tpd(CMOS)
Propagation Delay From IN to
Any CMOS Output, Complementary
Outputs (CMSINVx = 1)
Mx[5:0] = 1
1.25
ns
Mx[5:0] > 1
1.32
ns
Temperature Variation of the
Propagation Delay From IN to
Any CMOS Output (CMSINVx = 1)
Mx[5:0] = 1
l
1.3
ps/°C
Mx[5:0] > 1
l
1.4
ps/°C
6954f
4
For more information www.linear.com/LTC6954
LTC6954
Electrical Characteristics
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C. VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V, unless
otherwise specified. All voltages are with respect to GND. (Note 2)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Output Skews
tSKEW
Skew: Any LVPECL Output to
Any LVPECL Output
Mx[5:0], My[5:0] Both = 1 or Both > 1
IBIASx = 0 or 1
Skew: Any LVPECL Output to
Any LVDS Output
MLVPECL[5:0], MLVDS[5:0] Both = 1 or Both > 1
IBIASx = 0 or 1, LVCSy = 1
65
ps
Skew: Any LVPECL Output to
Any LVDS Output
MLVPECL[5:0] = MLVDS[5:0] = 1 or Both > 1
IBIASx = 0 or 1, LVCSx = 0
120
ps
Skew: Any LVPECL Output to
Any CMOS Output
MLVPECL[5:0], MCMOS[5:0] Both = 1 or Both > 1
IBIASx = 0 or 1, CMSINVy = 1
875
ps
Skew: Any LVDS Output to
Any LVDS Output
Mx[5:0], My[5:0] Both = 1 or Both > 1
LVCSx = 1 for Both Outputs
Skew: Any LVDS Output to
Any LVDS Output
Mx[5:0], My[5:0] Both = 1 or Both > 1
LVCSx = 0 for Both Outputs
5
ps
Skew: Any LVDS Output (LVCSx = 1) to Mx[5:0], My[5:0] Both = 1 or Both > 1
Any LVDS Output (LVCSy = 0)
LVCSx = 1, LVCSy = 0
50
ps
800
ps
l
l
–50
50
–50
50
ps
ps
Skew: Any LVDS Output to
Any CMOS Output
MLVDS[5:0], MCMOS[5:0] Both = 1 or Both > 1
LVCSx = 1, CMSINV = 1
Skew: Any CMOS Output to
Any CMOS Output
Mx[5:0], My[5:0] Both = 1 or Both > 1
CMSINV = 1
5
ps
Skew: Any CMOS Output to
Any CMOS Output, the First Output is
Complementary, the Second Output is
In-Phase
CMSINVx = 1, CMSINVy = 0
30
ps
Additional Skew: Any Output to Any
Output, Dividers Not the Same
Mx[5:0] = 1, My[5:0] > 1
l
35
70
120
ps
6954f
For more information www.linear.com/LTC6954
5
LTC6954
Electrical Characteristics
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C. VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V, unless
otherwise specified. All voltages are with respect to GND. (Note 2)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Supply Voltages
VA+ Supply Range
l
3.15
3.3
3.45
V
VD+ Supply Range
l
3.15
3.3
3.45
V
l
3.15
3.3
3.45
V
l
3.15
3.3
3.45
V
+ Supply Range
VIN
+, V
VOUT0
Range
OUT1
+, V
OUT2
+ Supply
Supply Current (Sum of VA+, VD+, VIN+, VOUT0+, VOUT1+, VOUT2+ Supply Currents)
LTC6954-1
LTC6954-2
LTC6954-3
LTC6954-4
ALL LTC6954 Variants
fIN = 1400MHz, Power-Up Default Configuration,
OUT0SEL = OUT1SEL = OUT2SEL = VA+,
IBIAS On for All Outputs,
Outputs Terminated with 100Ω Differential
l
300
335
mA
fIN = 1400MHz, Power-Up Default Configuration,
OUT0SEL = OUT1SEL = OUT2SEL = GND,
IBIAS Off for All Outputs,
Outputs Terminated with 50Ω to (VOUTx+ – 2V)
l
310
350
mA
fIN = 1400MHz, Power-Up Default Configuration,
OUT0SEL = OUT1SEL = OUT2SEL = VA+,
IBIAS On for LVPECL Outputs,
LVDS/CMOS = LVDS,
Outputs Terminated with 100Ω Differential
l
290
325
mA
fIN = 1400MHz, Power-Up Default Configuration,
OUT0SEL = OUT1SEL = VA+, OUT2SEL = GND,
IBIAS On for LVPECL Outputs,
LVDS/CMOS = CMOS, M2[5:0] = 28, fOUT2 = 50MHz,
LVPECL Outputs Terminated with 100Ω Differential
l
280
320
mA
fIN = 1400MHz, Power-Up Default Configuration,
OUT0SEL = OUT1SEL = OUT2SEL = VA+,
IBIAS On for LVPECL Output,
LVDS/CMOS = LVDS,
Outputs Terminated with 100Ω Differential
l
280
320
mA
fIN = 1400MHz, Power-Up Default Configuration,
OUT0SEL = VA+, OUT1SEL = OUT2SEL = GND,
IBIAS On for LVPECL Output,
LVDS/CMOS = CMOS, M1[5:0] = M2[5:0] = 28,
fOUT1 = fOUT2 = 50MHz,
LVPECL Output Terminated with 100Ω Differential
l
278
315
mA
fIN = 1400MHz, Power-Up Default Configuration, OUT0SEL
= OUT1SEL = OUT2SEL = VA+,
LVDS/CMOS = LVDS,
Outputs Terminated with 100Ω Differential
l
270
315
fIN = 1400MHz, Power-Up Default Configuration, OUT0SEL
= OUT1SEL = OUT2SEL = GND,
LVDS/CMOS = CMOS, M0[5:0], M1[5:0] = M2[5:0] = 28,
fOUT0 = fOUT1 = fOUT2 = 50MHz
l
282
310
PD(ALL) = 1
0.8
mA
mA
6954f
6
For more information www.linear.com/LTC6954
LTC6954
Electrical Characteristics
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C. VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V, unless
otherwise specified. All voltages are with respect to GND. (Note 2)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Supply Current Delta (Note 3)
Output Divider On, LVPECL
Output
Output Driver Only, LVPECL
Output Driver Only, LVDS
Output Driver Only, CMOS
PD_DIVx = 0, Mx[5:0] = 1, PD_OUTx = 1
l
28
32
mA
PD_DIVx = 0, Mx[5:0] > 1, PD_OUTx = 1
l
46
54
mA
PD_OUTx = 0, Termination = 50Ω to (VOUTx
l
43
50
mA
PD_OUTx = 0, IBIASx = 1 (Internal Bias On)
l
39
46
mA
PD_OUTx = 0, No Internal/External Bias
l
19
24
mA
PD_OUTx = 0, 3.5mA Mode, LVCSx = 0
l
31
37
mA
PD_OUTx = 0, 7mA Mode, LVCSx = 1
l
48
58
mA
PD_OUTx = 0, CMOS at 50MHz
l
35
43
mA
+ – 2V)
Digital Inputs (CS, SDI, SCLK, SYNC, OUT0SEL, OUT1SEL, OUT2SEL)
VIH
Input High Voltage
l
VIL
Input Low Voltage
l
VIHYS
Input Voltage Hysteresis
1.55
0.8
CS, SDI and SCLK Only
Input Current
V
250
l
–1
V
mV
1
µA
–1.5
mA
Digital Outputs (SDO)
IOH
High Level Output Current
SDO, VOH = VD+ – 400mV
l
IOL
Low Level Output Current
SDO, VOL = 400mV
l
2.2
l
–1
SDO Hi-Z Current
–2.4
3.4
mA
1
µA
Digital Timing Specifications (See Figure 11 and Figure 12)
tCKH
SCLK HIGH Pulse Width
l
25
ns
tCKL
SCLK LOW Pulse Width
l
25
ns
tCSS
CS Setup Time
l
10
ns
tCSH
CS HIGH Pulse Width
l
10
ns
tCS
SDI to SCLK Setup Time
l
6
ns
tCH
SDI to SCLK Hold Time
l
6
ns
l
1
tDO
SDO Propagation Delay
tSYNCH
SYNC HIGH Pulse Width
tSYNCL
Minimum SYNC LOW Pulse
Width
CLOAD = 10pF
Before Next SYNC HIGH Pulse
16
ns
ms
1
ms
6954f
For more information www.linear.com/LTC6954
7
LTC6954
Electrical Characteristics
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C. VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V, unless
otherwise specified. All voltages are with respect to GND. (Note 2)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
LVPECL Additive Phase Noise/Time Jitter (Note 5)
Phase Noise:
fIN = 622.08MHz, Mx[5:0] = 1, fOUT = 622.08MHz
10Hz Offset
–130
dBc/Hz
100Hz Offset
–139
dBc/Hz
1kHz Offset
–148
dBc/Hz
10kHz Offset
–156
dBc/Hz
100kHz Offset
–158
dBc/Hz
>1MHz Offset
–158
dBc/Hz
Jitter:
fIN = 622.08MHz, Mx[5:0] = 1, fOUT = 622.08MHz
12kHz to 20MHz Integration Bandwidth
20
fsRMS
10Hz to 311.04MHz Integration Bandwidth
80
fsRMS
Phase Noise:
fIN = 622.08MHz, Mx[5:0] = 4, fOUT = 155.52MHz
10Hz Offset
–138
dBc/Hz
100Hz Offset
–147
dBc/Hz
1kHz Offset
–156
dBc/Hz
10kHz Offset
–163
dBc/Hz
100kHz Offset
–165
dBc/Hz
>1MHz Offset
–165
dBc/Hz
Jitter:
fIN = 622.08MHz, Mx[5:0] = 4, fOUT = 155.52MHz
12kHz to 20MHz Integration Bandwidth
36
fsRMS
10Hz to 77.75MHz Integration Bandwidth
72
fsRMS
Phase Noise:
fIN = 622.08MHz, Mx[5:0] = 16, fOUT = 38.88MHz
10Hz Offset
–147
dBc/Hz
100Hz Offset
–159
dBc/Hz
1kHz Offset
–167
dBc/Hz
10kHz Offset
–170
dBc/Hz
100kHz Offset
–171
dBc/Hz
Phase Noise:
fIN = 245.76MHz, Mx[5:0] = 1, fOUT = 245.76MHz
>1MHz Offset
–171
dBc/Hz
10Hz Offset
–137
dBc/Hz
100Hz Offset
–147
dBc/Hz
1kHz Offset
–156
dBc/Hz
10kHz Offset
–161
dBc/Hz
100kHz Offset
–162
dBc/Hz
>1MHz Offset
–162
dBc/Hz
33
fsRMS
Jitter:
fIN = 245.76MHz, Mx[5:0] = 1, fOUT = 245.76MHz
12kHz to 20MHz Integration Bandwidth
81
fsRMS
Phase Noise:
fIN = 245.76MHz, Mx[5:0] = 4, fOUT = 61.44MHz
10Hz Offset
–140
dBc/Hz
100Hz Offset
–153
dBc/Hz
1kHz Offset
–161
dBc/Hz
10kHz Offset
–166
dBc/Hz
100kHz Offset
–168
dBc/Hz
>1MHz Offset
–168
dBc/Hz
65
fsRMS
Jitter:
fIN = 245.76MHz, Mx[5:0] = 4, fOUT = 61.44MHz
10Hz to 122.88MHz Integration Bandwidth
12kHz to 20MHz Integration Bandwidth
6954f
8
For more information www.linear.com/LTC6954
LTC6954
Electrical Characteristics
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C. VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V, unless
otherwise specified. All voltages are with respect to GND. (Note 2)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
LVPECL Additive Phase Noise/Time Jitter (Note 5)
Phase Noise:
fIN = 1400MHz, Mx[5:0] = 1, fOUT = 1400MHz
10Hz Offset
–126
dBc/Hz
100Hz Offset
–132
dBc/Hz
1kHz Offset
–143
dBc/Hz
10kHz Offset
–149
dBc/Hz
100kHz Offset
–152.5
dBc/Hz
>1MHz Offset
–152.5
dBc/Hz
Jitter:
fIN = 1400MHz, Mx[5:0] = 1, fOUT = 1400MHz
12kHz to 20MHz Integration Bandwidth
17
fsRMS
10Hz to 700MHz Integration Bandwidth
100
fsRMS
Phase Noise:
fIN = 1400MHz, Mx[5:0] = 4, fOUT = 350MHz
10Hz Offset
–132
dBc/Hz
100Hz Offset
–139
dBc/Hz
1kHz Offset
–151
dBc/Hz
10kHz Offset
–157
dBc/Hz
100kHz Offset
–160
dBc/Hz
>1MHz Offset
Jitter:
fIN = 1400MHz, Mx[5:0] = 4, fOUT = 350MHz
–160
dBc/Hz
12kHz to 20MHz Integration Bandwidth
29
fsRMS
10Hz to 175MHz Integration Bandwidth
85
fsRMS
10Hz Offset
–130
dBc/Hz
100Hz Offset
–138
dBc/Hz
1kHz Offset
–148
dBc/Hz
10kHz Offset
–156
dBc/Hz
100kHz Offset
–157.5
dBc/Hz
>1MHz Offset
–157.5
dBc/Hz
21
fsRMS
LVDS Additive Phase Noise/Time Jitter LVCS = 1 (Note 5)
Phase Noise:
fIN = 622.08MHz, Mx[5:0] = 1, fOUT = 622.08MHz
Jitter:
fIN = 622.08MHz, Mx[5:0] = 1, fOUT = 622.08MHz
12kHz to 20MHz Integration Bandwidth
83
fsRMS
Phase Noise:
fIN = 622.08MHz, Mx[5:0] = 4, fOUT = 155.52MHz
10Hz Offset
–140
dBc/Hz
100Hz Offset
–147
dBc/Hz
1kHz Offset
–157
dBc/Hz
10kHz Offset
–163
dBc/Hz
100kHz Offset
–165
dBc/Hz
>1MHz Offset
–165
dBc/Hz
36
fsRMS
10Hz to 311.04MHz Integration Bandwidth
Jitter:
fIN = 622.08MHz, Mx[5:0] = 4, fOUT = 155.52MHz
12kHz to 20MHz Integration Bandwidth
72
fsRMS
Phase Noise:
fIN = 622.08MHz, Mx[5:0] = 16, fOUT = 38.88MHz
10Hz Offset
–147
dBc/Hz
100Hz Offset
–159
dBc/Hz
1kHz Offset
–166
dBc/Hz
10kHz Offset
–170
dBc/Hz
100kHz Offset
–170
dBc/Hz
>1MHz Offset
–170
dBc/Hz
10Hz to 77.75MHz Integration Bandwidth
6954f
For more information www.linear.com/LTC6954
9
LTC6954
Electrical Characteristics
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C. VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V, unless
otherwise specified. All voltages are with respect to GND. (Note 2)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
LVDS Additive Phase Noise/Time Jitter LVCS = 1 (Note 5)
Phase Noise:
fIN = 245.76MHz, Mx[5:0] = 1, fOUT = 245.76MHz
10Hz Offset
–138
dBc/Hz
100Hz Offset
–146
dBc/Hz
1kHz Offset
–155
dBc/Hz
10kHz Offset
–160
dBc/Hz
100kHz Offset
–162
dBc/Hz
>1MHz Offset
–162
dBc/Hz
34
fsRMS
Jitter:
fIN = 245.76MHz, Mx[5:0] = 1, fOUT = 245.76MHz
12kHz to 20MHz Integration Bandwidth
83
fsRMS
Phase Noise:
fIN = 245.76MHz, Mx[5:0] = 4, fOUT = 61.44MHz
10Hz Offset
–142
dBc/Hz
100Hz Offset
–153
dBc/Hz
1kHz Offset
–162
dBc/Hz
10kHz Offset
–167
dBc/Hz
100kHz Offset
–168
dBc/Hz
>1MHz Offset
–168
dBc/Hz
65
fsRMS
10Hz to 122.88MHz Integration Bandwidth
Jitter:
fIN = 245.76MHz, Mx[5:0] = 4, fOUT = 61.4MHz
12kHz to 20MHz Integration Bandwidth
Phase Noise:
fIN = 1400MHz, Mx[5:0] = 1, fOUT = 1400MHz
10Hz Offset
–121
dBc/Hz
100Hz Offset
–133
dBc/Hz
1kHz Offset
–142
dBc/Hz
10kHz Offset
–148
dBc/Hz
100kHz Offset
–152
dBc/Hz
>1MHz Offset
–152
dBc/Hz
18
fsRMS
Jitter:
fIN = 1400MHz, Mx[5:0] = 1, fOUT = 1400MHz
12kHz to 20MHz Integration Bandwidth
10Hz to 700MHz Integration Bandwidth
109
fsRMS
Phase Noise:
fIN = 1400MHz, Mx[5:0] = 4, fOUT = 350MHz
10Hz Offset
–129
dBc/Hz
100Hz Offset
–137
dBc/Hz
1kHz Offset
–148
dBc/Hz
10kHz Offset
–156
dBc/Hz
100kHz Offset
–159
dBc/Hz
>1MHz Offset
–160
dBc/Hz
12kHz to 20MHz Integration Bandwidth
30
fsRMS
10Hz to 175MHz Integration Bandwidth
90
fsRMS
Jitter:
fIN = 1400MHz, Mx[5:0] = 4, fOUT = 350MHz
6954f
10
For more information www.linear.com/LTC6954
LTC6954
Electrical Characteristics
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C. VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V, unless
otherwise specified. All voltages are with respect to GND. (Note 2)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
LVDS Additive Phase Noise/Time Jitter LVCS = 0 (Note 5)
Phase Noise:
fIN = 622.08MHz, Mx[5:0] = 1, fOUT = 622.08MHz
10Hz Offset
–123
dBc/Hz
100Hz Offset
–135
dBc/Hz
1kHz Offset
–146
dBc/Hz
10kHz Offset
–151
dBc/Hz
100kHz Offset
–153
dBc/Hz
>1MHz Offset
–153
dBc/Hz
36
fsRMS
Jitter:
fIN = 622.08MHz, Mx[5:0] = 1, fOUT = 622.08MHz
12kHz to 20MHz Integration Bandwidth
10Hz to 311.04MHz Integration Bandwidth
140
fsRMS
Phase Noise:
fIN = 622.08MHz, Mx[5:0] = 4, fOUT = 155.52MHz
10Hz Offset
–135
dBc/Hz
100Hz Offset
–146
dBc/Hz
1kHz Offset
–154
dBc/Hz
10kHz Offset
–160
dBc/Hz
100kHz Offset
–161
dBc/Hz
>1MHz Offset
–161
dBc/Hz
29
fsRMS
Jitter:
fIN = 622.08MHz, Mx[5:0] = 4, fOUT = 155.52MHz
12kHz to 20MHz Integration Bandwidth
10Hz to 77.75MHz Integration Bandwidth
114
fsRMS
Phase Noise:
fIN = 622.08MHz, Mx[5:0] = 16, fOUT = 38.88MHz
10Hz Offset
–147
dBc/Hz
100Hz Offset
–157
dBc/Hz
1kHz Offset
–165
dBc/Hz
10kHz Offset
–167
dBc/Hz
100kHz Offset
–167
dBc/Hz
>1MHz Offset
–167
dBc/Hz
6954f
For more information www.linear.com/LTC6954
11
LTC6954
Electrical Characteristics
The l denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at TA = 25°C. VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V, unless
otherwise specified. All voltages are with respect to GND. (Note 2)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
CMOS Additive Phase Noise/Time Jitter (Note 5)
Phase Noise:
fIN = 622.08MHz, Mx[5:0] = 4,
fOUT = 155.52MHz
10Hz Offset
–129
dBc/Hz
100Hz Offset
–143
dBc/Hz
1kHz Offset
–158
dBc/Hz
10kHz Offset
–161
dBc/Hz
100kHz Offset
–162
dBc/Hz
>1MHz Offset
–162
dBc/Hz
Jitter:
fIN = 622.08MHz, Mx[5:0] = 4,
fOUT = 155.52MHz
12kHz to 20MHz Integration Bandwidth
52
fsRMS
10Hz to 77.75MHz Integration Bandwidth
102
fsRMS
Phase Noise:
fIN = 245.76MHz, Mx[5:0] = 1,
fOUT = 245.76MHz
10Hz Offset
–129
dBc/Hz
100Hz Offset
–139
dBc/Hz
Jitter:
fIN = 245.76MHz, Mx[5:0] = 1,
fOUT = 245.76MHz
Phase Noise:
fIN = 245.76MHz, Mx[5:0] = 4,
fOUT = 61.44MHz
Jitter:
fIN = 245.76MHz, Mx[5:0] = 4,
fOUT = 61.44MHz
1kHz Offset
–146
dBc/Hz
10kHz Offset
–155
dBc/Hz
100kHz Offset
–159
dBc/Hz
>1MHz Offset
–160
dBc/Hz
12kHz to 20MHz Integration Bandwidth
42
fsRMS
10Hz to 122.88MHz Integration Bandwidth
102
fsRMS
10Hz Offset
–135
dBc/Hz
100Hz Offset
–147
dBc/Hz
1kHz Offset
–156
dBc/Hz
10kHz Offset
–163
dBc/Hz
100kHz Offset
–166
dBc/Hz
>1MHz Offset
–166
dBc/Hz
82
fsRMS
12kHz to 20MHz Integration Bandwidth
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC6954I is guaranteed to meet specified performance limits
over the full operating junction temperature range of –40°C to 105°C.
Under maximum operating conditions, air flow or heat sinking may
be required to maintain a junction temperature of 105°C or lower. It is
strongly recommended that the exposed pad (pin 37) be soldered directly
to the ground plane with an array of thermal vias as described in the
Applications Information section.
Note 3: The supply current delta specifications refer to the amount of
supply current that each individual block consumes. Powering on or off
this circuit block adds or subtracts this much current from the total supply
current consumed in any given configuration.
Note 4: The skews are defined as the second listed output's transition
relative to the first listed output's transition. If the second listed output
transitions after the first listed output, the skew is positive.
For the same divider setting, LVPECL outputs have nominally the same
skew regardless of the IBIAS setting (IBIASx = 0 or 1), for the same
divider setting, all LVDS and CMOS outputs transition after the LVPECL
outputs, thus these skews are positive. For the same divider setting, all
CMOS outputs transition after all LVDS outputs, thus these skews are
positive. For the same divider setting, LVDS outputs with the 3.5mA
current setting (LVCS = 0) transition after LVDS outputs with the 7mA
current setting (LVCS = 1), thus these skews are positive. For the same
divider setting, in-phase CMOS outputs (CMSINVx = 0) transition after
complementary outputs (CMSINVx = 1), thus this skew is positive.
For the same output type, outputs with the divider setting greater than
one (Mx[5:0] > 1) transition after outputs with the divider equal to one
(Mx[5:0] = 1), thus this additional skew is positive.
Note 5: Additive phase noise and jitter are the phase noise added by the
LTC6954. It does not include noise from the external signal source.
6954f
12
For more information www.linear.com/LTC6954
LTC6954
Typical
Performance Characteristics
VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V.
TA = 25°C, unless otherwise specified. All voltages are with respect to GND.
LVPECL Differential Output
at 800MHz, IBIAS Enabled,
RTERM = 100Ω Differential
1.6
0.6
0.6
1.5
0.4
0.4
0.2
0
–0.2
–0.4
0.2
0
–0.2
–0.4
–0.6
0.5
1.0
1.5
2.0
TIME (ns)
2.5
–0.8
3.0
0.6
0.6
0.4
0.4
AMPLITUDE (VPP_DIFF)
AMPLITUDE (VPP_DIFF)
0.8
0.2
0
–0.2
–0.4
3.0
0.4
0.4
0.3
0.3
AMPLITUDE (VPP_DIFF)
0.5
0.2
0.1
0
–0.1
–0.2
1.0
0.9
1.6
0
1
2
3
TIME (ns)
4
5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.6
6
5
6954 G07
2000
6954 G06
0.80
–0.2
–0.5
500
1000
1500
FREQUENCY (MHz)
0
LVDS Differential Output Swing
vs Frequency, ILVDS = 3.5mA,
RTERM = 100Ω (Differential)
0
–0.4
2000
6954 G03
LVPECL Differential Output Swing
vs Frequency, IBIAS Disabled,
RTERM = 50Ω to V+ – 2V
6954 G05
–0.1
–0.4
500
1000
1500
FREQUENCY (MHz)
0
0.7
0.1
–0.3
4
1.1
6954 G02
0.2
–0.3
2
3
TIME (ns)
1.2
LVDS Differential Output
at 300MHz, ILVDS = 3.5mA,
RTERM = 100Ω (Differential)
0.5
1
1.3
1.5
6954 G04
LVDS Differential Output
at 800MHz, ILVDS = 3.5mA,
RTERM = 100Ω (Differential)
0
1.4
0.8
6
–0.4
–0.8
–0.5
5
–0.2
–0.8
2.5
4
0
–0.6
1.5
2.0
TIME (ns)
3
TIME (ns)
0.2
–0.6
1.0
2
LVPECL Differential Output
at 800MHz, IBIAS Disabled,
RTERM = 50Ω to V+ – 2V
0.8
0.5
1
6954 G01
LVPECL Differential Output
at 1400MHz, IBIAS Disabled,
RTERM = 50Ω to V+ – 2V
0
0
DIFFERENTIAL AMPLITUDE (VPP)
0
DIFFERENTIAL AMPLITUDE (VPP)
–0.8
DIFFERENTIAL AMPLITUDE (VPP)
0.8
–0.6
AMPLITUDE (VPP_DIFF)
LVPECL Differential Output Swing
vs Frequency, IBIAS Enabled,
RTERM = 100Ω Differential
0.8
AMPLITUDE (VPP_DIFF)
AMPLITUDE (VPP_DIFF)
LVPECL Differential Output
at 1400MHz, IBIAS Enabled,
RTERM = 100Ω Differential
0
2
4
6
TIME (ns)
8
10
12
6954 G08
0.75
0.70
0.65
0.60
0.55
0.50
0.45
0.40
0
200
400 600 800 1000 1200 1400
FREQUENCY (MHz)
6954 G09
6954f
For more information www.linear.com/LTC6954
13
LTC6954
Typical Performance Characteristics
VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V.
TA = 25°C, unless otherwise specified. All voltages are with respect to GND.
0.5
0.8
0.4
0.6
AMPLITUDE (VPP_DIFF)
0.2
0.1
0
–0.1
–0.2
–0.3
0.4
0.2
0
–0.2
–0.4
–0.8
0 0.25 0.50 0.75 1.0 1.25 1.50 1.75 2.0 2.25 2.50
TIME (ns)
6954 G10
3.0
3.0
2.5
2.5
2.0
1.5
1.0
0.5
0
2
0
4
6
8
10
TIME (ns)
12
14
2 2.5 3
TIME (ns)
3.5
4
–140
–150
DIV = 4
DIV = 16
–170
0.60
0.55
0.50
0.45
500
0
6954 G11
1000
1500
FREQUENCY (MHz)
2000
6954 G12
CMOS Output Swing
vs Frequency and CLOAD
2pF
3.0
1.5
1.0
–120
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 1.4GHz
–160
0.65
0.40
5
4.5
0.70
3.2
4.7pF
10pF
2.8
2.6
2.4
2.2
0
5
6954 G13
–130
–180
1.5
2.0
0
16
ADDITIVE PHASE NOISE (dBc/Hz)
ADDITIVE PHASE NOISE (dBc/Hz)
–120
1
0.5
LVPECL Output Additive Phase Noise,
fIN = 1400MHz, IBIAS Enabled,
RTERM = 100Ω Differential
–110
0.5
0.75
CMOS Output at 100MHz,
CMSINV = 1, CLOAD = 2pF
AMPLITUDE (V)
AMPLITUDE (V)
CMOS Output at 250MHz,
CMSINV = 1, CLOAD = 2pF
0
VPP SINGLE-ENDED (V)
–0.5
0.80
–0.6
–0.4
LVDS Differential Output Swing
vs Frequency, ILVDS = 7mA,
RTERM = 100Ω||100Ω (Differential)
10
15 20 25
TIME (ns)
30
2.0
40
35
LVPECL Output Additive Phase
Noise, fIN = 622.08MHz, IBIAS
Enabled, RTERM = 100Ω Differential
–130
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 622.08MHz
–130
–140
–150
DIV = 1
–160
0
6954 G14
ADDITIVE PHASE NOISE (dBc/Hz)
AMPLITUDE (VPP_DIFF)
0.3
LVDS Differential Output
at 800MHz, ILVDS = 7mA,
RTERM = 100Ω||100Ω (Differential)
DIFFERENTIAL AMPLITUDE (VPP)
LVDS Differential Output
at 1400MHz, ILVDS = 7mA,
RTERM = 100Ω||100Ω (Differential)
DIV = 4
–170
50 100 150 200 250 300 350 400 450 500
FREQUENCY (MHz)
6954 G15
LVPECL Output Additive Phase
Noise, fIN = 245.76MHz, IBIAS
Enabled, RTERM = 100Ω Differential
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 245.76MHz
–140
–150
DIV = 1
–160
DIV = 4
–170
DIV = 16
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
10M
6954 G16
–180
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
10M
6954 G17
–180
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
10M
6954 G18
6954f
14
For more information www.linear.com/LTC6954
LTC6954
Typical
Performance Characteristics
TA = 25°C, unless otherwise specified. All voltages are with respect to GND.
LVPECL Output Additive Phase
Noise, fIN = 622.08MHz, IBIAS
Disabled, RTERM = 50Ω to V+ – 2V
LVPECL Output Additive Phase
Noise, fIN = 1400MHz, IBIAS
Disabled, RTERM = 50Ω to V+ – 2V
–120
–140
DIV = 1
–150
DIV = 4
–160
–170
–180
DIV = 16
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
DIV = 1
–150
DIV = 4
–160
DIV = 16
–170
–180
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
10
ADDITIVE PHASE NOISE (dBc/Hz)
ADDITIVE PHASE NOISE (dBc/Hz)
–150
DIV = 4
DIV = 16
–170
–180
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
10M
6954 G25
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
–150
DIV = 1
–160
–170
DIV = 4
10
DIV = 1
–160
DIV = 4
–170
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
–140
–150
DIV = 1
–160
DIV = 4
–170
DIV = 16
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 122.88MHz
–150
DIV = 1
–160
DIV = 4
–170
10
100
6954 G23
LVDS Output Additive Phase Noise,
fIN = 622.08MHz, ILVDS = 7mA,
RTERM = 100Ω||100Ω (Differential)
–130
10M
6954 G26
10M
6954 G21
–140
–180
10M
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 622.08MHz
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
LVDS Output Additive Phase Noise,
fIN = 122.88MHz, ILVDS = 3.5mA,
RTERM = 100Ω Differential
–130
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 245.76MHz
–150
100
6954 G20
–140
–180
–140
–180
10M
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 245.76MHz
LVDS Output Additive Phase Noise,
fIN = 245.76MHz, ILVDS = 3.5mA,
RTERM = 100Ω Differential
–120
DIV = 1
–160
100
6954 G22
–130
–140
DIV = 16
–130
–180
10M
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 1.4GHz
–120
DIV = 4
–170
LVDS Output Additive Phase Noise,
fIN = 1400MHz, ILVDS = 7mA, RTERM
= 100Ω||100Ω (Differential)
–110
DIV = 1
–160
–120
ADDITIVE PHASE NOISE (dBc/Hz)
ADDITIVE PHASE NOISE (dBc/Hz)
–140
–150
6954 G19
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 622.08MHz
–130
–140
–180
10M
LVDS Output Additive Phase Noise,
fIN = 622.08MHz, ILVDS = 3.5mA,
RTERM = 100Ω Differential
–120
–130
ADDITIVE PHASE NOISE (dBc/Hz)
–130
–130
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 622.08MHz
ADDITIVE PHASE NOISE (dBc/Hz)
–120
LVPECL Output Additive Phase
Noise, fIN = 245.76MHz, IBIAS
Disabled, RTERM = 50Ω to V+ – 2V
–120
ADDITIVE PHASE NOISE (dBc/Hz)
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 1.4GHz
ADDITIVE PHASE NOISE (dBc/Hz)
ADDITIVE PHASE NOISE (dBc/Hz)
–110
VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V.
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
10M
6954 G24
LVDS Output Additive Phase Noise,
fIN = 245.76MHz, ILVDS = 7mA,
RTERM = 100Ω||100Ω (Differential)
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 245.76MHz
–130
–140
–150
DIV = 1
–160
DIV = 4
–170
–180
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
10M
6954 G27
6954f
For more information www.linear.com/LTC6954
15
LTC6954
Typical Performance Characteristics
TA = 25°C, unless otherwise specified. All voltages are with respect to GND.
–140
DIV = 1
–150
–160
DIV = 4
–170
–150
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 122.88MHz
–130
–153
PHASE NOISE FLOOR (dBc/Hz)
ADDITIVE PHASE NOISE (dBc/Hz)
ADDITIVE PHASE NOISE (dBc/Hz)
–120
SINGLE-ENDED SINE WAVE INPUT
+7dBm AT 245.76MHz
–130
Additive Phase Noise Floor vs Divider
Ratio FIN = 1GHz, LVPECL IBIAS
Enabled RTERM = 100Ω Differential
CMOS Output Additive Phase
Noise, fIN = 122.88MHz
CMOS Output Additive Phase
Noise, fIN = 245.76MHz
–120
VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V.
–140
DIV = 1
–150
–160
DIV = 4
–170
–156
–159
–162
–165
–168
–171
–174
–177
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
10M
–180
260
280
240
260
220
240
200
220
180
160
140
120
100
140
100
40
80
2000
ALL DIVIDERS AND LVPECL OUTPUTS ON, DIV BY 1
TWO DIVIDERS AND LVPECL OUTPUTS ON, DIV BY 1
DIVIDER DIV BY 2 AND LVPECL OUTPUT ON
DIVIDER DIV BY 1 AND LVPECL OUTPUT ON
DIVIDER DIV BY 1 ON, LVPECL OUTPUT OFF 6954 G31
60
0
400
1200
800
1600
FREQUENCY (MHz)
1
2
4
8
16
DIVIDER RATIO
32
64
6954 G30
Supply Current vs Frequency,
CMOS Output
160
60
1200
800
1600
FREQUENCY (MHz)
10M
6954 G29
180
80
400
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
200
120
0
100
Supply Current vs Frequency,
LVPECL Output, IBIAS Disabled,
RTERM = 50Ω to V+ – 2V
CURRENT (mA)
CURRENT (mA)
Supply Current vs Frequency,
LVPECL Output, IBIAS Enabled,
RTERM = 100Ω Differential
20
10
6954 G28
–180
CURRENT (mA)
–180
2000
ALL DIVIDERS AND LVPECL OUTPUTS ON, DIV BY 1
TWO DIVIDERS AND LVPECL OUTPUTS ON, DIV BY 1
DIVIDER DIV BY 2 AND LVPECL OUTPUT ON
DIVIDER DIV BY 1 AND LVPECL OUTPUT ON
DIVIDER DIV BY 1 ON, LVPECL OUTPUT OFF 6954 G32
300
280
260
240
220
200
180
160
140
120
100
80
60
40
20
0
100
300
200
400
OUTPUT FREQUENCY (MHz)
500
ALL DIVIDERS AND CMOS OUTPUTS ON, DIV BY 1
TWO DIVIDERS AND CMOS OUTPUTS ON, DIV BY 1
DIVIDER DIV BY 2 AND CMOS OUTPUT ON
DIVIDER DIV BY 1 AND CMOS OUTPUT ON
DIVIDER DIV BY 1 ON, CMOS OUTPUT OFF
6954 G33
6954f
16
For more information www.linear.com/LTC6954
LTC6954
Typical Performance Characteristics
VA+ = VD+ = VIN+ = VOUT0+ = VOUT1+ = VOUT2+ = 3.3V.
TA = 25°C, unless otherwise specified. All voltages are with respect to GND.
Supply Current vs Frequency,
LVDS Output, ILVDS = 3.5mA,
RTERM = 100Ω Differential
Supply Current vs Frequency,
LVDS Output, ILVDS = 7mA,
RTERM = 100Ω||100Ω (Differential)
240
280
220
260
200
240
220
160
CURRENT (mA)
CURRENT (mA)
180
140
120
100
200
180
160
140
120
80
100
60
80
40
60
20
0
200
400 600 800 1000 1200 1400
FREQUENCY (MHz)
ALL DIVIDERS AND LVDS OUTPUTS ON, DIV BY 1
TWO DIVIDERS AND LVDS OUTPUTS ON, DIV BY 1
DIVIDER DIV BY 2 AND LVDS OUTPUT ON
DIVIDER DIV BY 1 AND LVDS OUTPUT ON
DIVIDER DIV BY 1 ON, LVDS OUTPUT OFF
6954 G34
40
0
400
1200
800
1600
FREQUENCY (MHz)
2000
ALL DIVIDERS AND LVDS OUTPUTS ON, DIV BY 1
TWO DIVIDERS AND LVDS OUTPUTS ON, DIV BY 1
DIVIDER DIV BY 2 AND LVDS OUTPUT ON
DIVIDER DIV BY 1 AND LVDS OUTPUT ON
DIVIDER DIV BY 1 ON, LVDS OUTPUT OFF
6954 G35
6954f
For more information www.linear.com/LTC6954
17
LTC6954
Pin Functions
LTC6954
VOUT0+, VOUT1+, VOUT2+ (Pins 1, 4, 5, 8, 9, 12): Output
Supply Voltages. The supply range is from 3.15V to 3.45V.
This supply should be kept free of noise and ripple. The
use of a low impedance power plane is recommended. All
VOUTx+ pins must be connected to the same supply voltage as the VA+, VD+ and VIN+ pins. Each pin, or in some
cases pin pairs, must be separately bypassed directly to
GND with a 0.01µF ceramic capacitor as close to the pin
as possible. Refer to the Applications Information section
for more details on supply connections and bypassing.
GND (Pins 14, 26, 29, 32, 35): Ground Connections.
Should be tied directly to the exposed pad (pin 37) and to
a low impedance ground plane for best performance. Refer
to the Applications Information section for more details on
grounding for signal integrity and thermal considerations.
VA+ (Pins 15, 23, 24, 34): Analog Supply Voltages. The
supply range is from 3.15V to 3.45V. This supply should
be kept free of noise and ripple. The use of a low impedance power plane is recommended. All VA+ pins must
be connected to the same supply voltage as the VOUTx+,
VD+ and VIN+ pins. Each pin, or in some cases pin pairs,
must be separately bypassed directly to GND with a 0.1µF
ceramic capacitor as close to the pin as possible. Refer
to the Applications Information section for more details
on supply connections and bypassing.
CS (Pin 16): Serial Port Chip Select Input. This active LOW
CMOS logic input initiates a serial port transaction when
brought LOW. It finalizes the serial port transaction when
brought HIGH after 16 serial port clock cycles. Refer to
the Operation section for more details.
SDO (Pin 17): Serial Data Output. Data read from the
serial port is presented on this CMOS logic pin. Refer to
the Operation section for more details.
VD+ (Pins 18, 21): Digital Supply Voltages. The supply
range is from 3.15V to 3.45V. This supply should be
kept free of noise and ripple. The use of a low impedance power plane is recommended. All VD+ pins must
be connected to the same supply voltage as the VOUTx+,
VA+ and VIN+ pins. Each pin must be separately bypassed
directly to GND with a 0.1µF ceramic capacitor as close
to the pin as possible. Refer to the Applications Informa-
tion section for more details on supply connections and
bypassing.
SCLK (Pin 19): Serial Port Clock Input. This positive edge
triggered CMOS logic input signal clocks serial port data
in on the rising edge. Refer to the Operation section for
more details.
SDI (Pin 20): Serial Port Data Input. Data written into the
serial port is presented on this CMOS logic pin. Refer to
the Operation section for more details.
SYNC (Pin 22): The Synchronization Input Pin. A rising
edge on this CMOS logic input initiates an output clock
synchronization sequence. Precision output synchronization of one or more parts is handled on-chip, so the timing
of this signal is not critical. Refer to the Operation and the
Applications Information sections for more details.
VIN+ (Pins 25, 30): Analog Supply Voltages. The supply
range is from 3.15V to 3.45V. This supply should be kept
free of noise and ripple. The use of a low impedance power
plane is recommended. All VIN+ pins must be connected
to the same supply voltage as the VOUTx+, VA+ and VD+
pins. Each pin must be separately bypassed directly to
GND with a 0.1µF ceramic capacitor as close to the pin
as possible. Refer to the Applications Information section
for more details on supply connections and bypassing.
IN+, IN – (Pins 27, 28): The Signal Input Pins. The input
signal can be either differential or single ended. It can be a
sine wave, LVPECL logic, LVDS logic or CMOS logic. Refer
to the Operation and Applications Information sections for
more details on the correct use of the inputs.
TEMP (Pin 31): Temperature Monitoring Diode. This pin
is connected to the anode of a diode that may be used to
measure the die temperature, by forcing a current and measuring the voltage. Refer to the Applications Information
section for more details on monitoring the die temperature.
GND (Exposed Pad Pin 37): Ground Connection. The package exposed pad must be soldered directly to the PCB land.
The PCB land pattern should have multiple thermal vias to
the ground plane for both low ground inductance and low
thermal resistance. Refer to the Applications Information
section for more details on grounding for signal integrity
and thermal considerations.
6954f
18
For more information www.linear.com/LTC6954
LTC6954
Pin Functions
LTC6954-1 OUTPUTS and Mode Select
LTC6954-2 OUTPUTS and Mode Select
OUT0SEL (Pin 13): OUT0 Mode Select. Connecting this
pin to the VA+ supply enables the internal, active biasing
of the OUT0 output emitter followers. Connecting this
pin to GND disables this internal bias circuit. Refer to the
Operation and Applications Information sections for more
details on the LVPECL internal bias.
OUT0SEL (Pin 13): OUT0 Mode Select. Connecting this
pin to the VA+ supply enables the internal, active biasing
of the OUT0 output emitter followers. Connecting this
pin to GND disables this internal bias circuit. Refer to the
Operation and Applications Information sections for more
details on the LVPECL internal bias.
OUT0–, OUT0+ (Pins 10, 11): LVPECL Output Pins.
Differential logic outputs typically terminated by 50Ω connected to a supply 2V below the VOUT0+ supply. Refer to
the Operation and Applications Information sections for
more details.
OUT0–, OUT0+ (Pins 10, 11): LVPECL Output Pins. Differential logic outputs typically terminated by 50Ω connected to a supply 2V below the VOUT0+ supply. Refer to
the Operation and Applications Information sections for
more details.
OUT1SEL (Pin 33): OUT1 Mode Select. Connecting this
pin to the VA+ supply enables the internal, active biasing
of the OUT1 output emitter followers. Connecting this
pin to GND disables this internal bias circuit. Refer to the
Operation and Applications Information sections for more
details on the LVPECL internal bias.
OUT1SEL (Pin 33): OUT1 Mode Select. Connecting this
pin to the VA+ supply enables the internal, active biasing
of the OUT1 output emitter followers. Connecting this
pin to GND disables this internal bias circuit. Refer to the
Operation and Applications Information sections for more
details on the LVPECL internal bias.
OUT1 –, OUT1+ (Pins 6, 7): LVPECL Output Pins.
Differential logic outputs typically terminated by 50Ω
connected to a supply 2V below the VOUT1+ supply. Refer
to the Operation and Applications Information sections
for more details.
OUT1–, OUT1+ (Pins 6, 7): LVPECL Output Pins. Differential
logic outputs typically terminated by 50Ω connected to a
supply 2V below the VOUT1+ supply. Refer to the Operation
and Applications Information sections for more details.
OUT2SEL (Pin 36): OUT2 Mode Select. Connecting this
pin to the VA+ supply enables the internal, active biasing
of the OUT2 output emitter followers. Connecting this
pin to GND disables this internal bias circuit. Refer to the
Operation and Applications Information sections for more
details on the LVPECL internal bias.
OUT2 –, OUT2+ (Pins 2, 3): LVPECL Output Pins.
Differential logic outputs typically terminated by 50Ω
connected to a supply 2V below the VOUT2+ supply. Refer
to the Operation and Applications Information sections
for more details.
OUT2SEL (Pin 36): OUT2 Mode Select. Connecting this pin
to ground configures OUT2 as a CMOS logic type output.
Connecting this pin to the VA+ supply configures OUT2
as an LVDS logic type output.
OUT2–, OUT2+ (Pins 2, 3): LVDS/CMOS Output Pins.
These outputs may be programmed as LVDS or CMOS
outputs using the OUT2SEL pin. Refer to the Operation and the Applications Information sections for
more details.
6954f
For more information www.linear.com/LTC6954
19
LTC6954
Pin Functions
LTC6954-3 OUTPUTS and Mode Select
LTC6954-4 OUTPUTS and Mode Select
OUT0SEL (Pin 13): OUT0 Mode Select. Connecting this
pin to the VA+ supply enables the internal, active biasing
of the OUT0 output emitter followers. Connecting this
pin to GND disables this internal bias circuit. Refer to the
Operation and Applications Information sections for more
details on the LVPECL internal bias.
OUT0SEL (Pin 13): OUT0 Mode Select. Connecting this
pin to GND configures OUT0 as a CMOS logic type output.
Connecting this pin to the VA+ supply configures OUT0 as
an LVDS logic type output.
OUT0–, OUT0+ (Pins 10, 11): LVPECL Output Pins. Differential logic outputs typically terminated by 50Ω connected to a supply 2V below the VOUT0+ supply. Refer to
the Operation and Applications Information sections for
more details.
OUT1SEL (Pin 33): OUT1 Mode Select. Connecting this
pin to GND configures OUT1 as a CMOS logic type output.
Connecting this pin to the VA+ supply configures OUT1 as
an LVDS logic type output.
OUT1–, OUT1+ (Pins 6, 7): LVDS/CMOS Output Pins. These
outputs may be programmed as LVDS or CMOS outputs
using the OUT1SEL pin. Refer to the Operation and the
Applications Information sections for more details.
OUT2SEL (Pin 36): OUT2 Mode Select. Connecting this
pin to GND configures OUT2 as a CMOS logic type output.
Connecting this pin to the VA+ supply configures OUT2 as
an LVDS logic type output.
OUT2–, OUT2+ (Pins 2, 3): LVDS/CMOS Output Pins. These
outputs may be programmed as LVDS or CMOS outputs
using the OUT2SEL pin. Refer to the Operation and the
Applications Information sections for more details.
OUT0–, OUT0+ (Pins 10, 11): LVDS/CMOS Output Pins.
These outputs may be programmed as LVDS or CMOS
outputs using the OUT0SEL pin. Refer to the Operation
and the Applications Information sections for more details.
OUT1SEL (Pin 33): OUT1 Mode Select. Connecting this
pin to GND configures OUT1 as a CMOS logic type output.
Connecting this pin to the VA+ supply configures OUT1 as
an LVDS logic type output.
OUT1–, OUT1+ (Pins 6, 7): LVDS/CMOS Output Pins. These
outputs may be programmed as LVDS or CMOS outputs
using the OUT1SEL pin. Refer to the Operation and the
Applications Information sections for more details.
OUT2SEL (Pin 36): OUT2 Mode Select. Connecting this
pin to GND configures OUT2 as a CMOS logic type output.
Connecting this pin to the VA+ supply configures OUT2 as
an LVDS logic type output.
OUT2–, OUT2+ (Pins 2, 3): LVDS/CMOS Output Pins. These
outputs may be programmed as LVDS or CMOS outputs
using the OUT2SEL pin. Refer to the Operation and the
Applications Information sections for more details.
6954f
20
For more information www.linear.com/LTC6954
LTC6954
Block Diagram
25 VIN+
15
23
24
34
VA+
VA+
VA+
VA+
26 GND
IN+
27
IN–
28
DELAY 0
DEL0 = 0 TO 63
OUTPUT 0
DRIVER
M0 DIVIDER
M0 = 1 TO 63
VOUT0+ 9
OUT0+
11
OUT0–
10
VOUT0+ 12
29 GND
30 VIN+
22
13
33
36
SYNC
20
16
31
DELAY 1
DEL1 = 0 TO 63
M1 DIVIDER
M1 = 1 TO 63
OUT1SEL
SDO
VOUT1+ 5
OUT1+
7
OUT1–
6
VOUT1+ 8
OUT2SEL
18 VD+
19
OUTPUT 1
DRIVER
OUT0SEL
21 VD+
17
SYNC
CONTROL
SPI
SERIAL
PORT
AND
DIGITAL
LOGIC
OUTPUT 2
DRIVER
DELAY 2
DEL2 = 0 TO 63
M2 DIVIDER
M2 = 1 TO 63
VOUT2+ 1
OUT2+
3
OUT2–
2
VOUT2+ 4
SCLK
SDI
CS
TEMP
32
GND
14
GND
35
GND
EXPOSED
GND PAD
GND
37
6954 BD
6954f
For more information www.linear.com/LTC6954
21
LTC6954
Timing Diagrams
Output Propagation Delays and Skews, Mx[5:0] = 1
IN–
IN+
tSKEWP0
OUT0–
OUT0+
tpdP1
OUT1–
OUT1+
tSKEWP2
OUT2–
OUT2+
6954 TD01
Differential LVPECL Rise/Fall Times
80%
20%
tRISE
tFALL
6954 TD02
Differential LVDS Rise/Fall Times
Single-Ended CMOS Rise/Fall Times
80%
80%
20%
20%
tRISE
tFALL
6954 TD03
tRISE
tFALL
6954 TD04
6954f
22
For more information www.linear.com/LTC6954
LTC6954
Operation
LTC6954 INTRODUCTION
As shown in Figure 1, the LTC6954 consists of two distinct circuit sections: multioutput clock distribution and
digital control.
The LTC6954 is a family of low phase noise clock distribution parts. Each part provides three outputs, each with
programmable frequency divider and delay blocks. There
are four members of the family differing in their output
logic signal type:
The clock distribution section of the LTC6954 receives
an input signal up to 1.4GHz (1.8GHz for the LTC6954-1
when DELx = 0) and delivers three output signals based
on the input. The output signal logic type depends on the
LTC6954 part version and the connection of the OUTxSEL
output mode selection pins. Table 1 shows all four part
versions, each version’s available output types and the
effect of OUTxSEL pin connection on the output.
LTC6954-1: Three LVPECL outputs
LTC6954-2: Two LVPECL and one LVDS/CMOS outputs
LTC6954-3: One LVPECL and two LVDS/CMOS outputs
The LVPECL logic outputs are capable of operation up
to 1.4GHz (1.8GHz for the LTC6954-1 when DELx = 0).
Connecting the OUTxSEL pin to the VA+ supply enables
the internal, active biasing of the output emitter followers.
Connecting this pin to GND disables this internal bias circuit.
LTC6954-4: Three LVDS/CMOS outputs
IN+
LTC6954-X
IN–
SYNC
SYNC
CONTROL
OUT0SEL
OUT1SEL
OUT2SEL
DIGITAL
CONTROL
SDO
SPI
SERIAL
PORT
SDI
SERIAL
PORT
AND
DIGITAL
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
OUT0+
OUT0–
OUT1+
OUT1–
CLOCK
DISTRIBUTION
OUT2+
OUT2–
SCLK
CS
6954 F01
Figure 1.The LTC6954 Highlighting the Circuit Blocks
Table 1. LTC6954 Versions and Output Configurations
LTC6954
VERSION
OUTPUT 0
OUTPUT 1
OUTPUT 2
OUT0SEL = GND
OUT0SEL = VA+
OUT1SEL = GND
OUT1SEL = VA+
OUT2SEL = GND
OUT2SEL = VA+
LTC6954-1
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LTC6954-2
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
CMOS
LVDS
LTC6954-3
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
CMOS
LVDS
CMOS
LVDS
LTC6954-4
CMOS
LVDS
CMOS
LVDS
CMOS
LVDS
6954f
For more information www.linear.com/LTC6954
23
LTC6954
Operation
The LVDS/CMOS output can be either a CMOS logic type
or an LVDS logic type as configured by the OUTxSEL
pin connection. Connecting the OUTxSEL pin to ground
configures the output as a CMOS logic output capable of
operation up to 250MHz. Connecting the OUTxSEL pin
to the VA+ supply configures the output as an LVDS logic
output capable of operation up to 800MHz for LVCSx set
to 0 (far end line termination only), and up to 1400MHz for
LVCSx set to 1 (doubly terminated). Refer to the Operation
and Applications Information sections for more details.
Regardless of the LTC6954 part version and the output
logic configuration, all three outputs are individually programmable to divide the input frequency by any integer
from 1 to 63 and to delay any output by 0 to 63 input
clock cycles. For an input signal with a 50% duty cycle,
the output duty cycle will always be 50% regardless of
the divide number.
The digital control section contains a full SPI-compatible
serial control bus, the three output mode selection
pins (OUT0SEL, OUT1SEL and OUT2SEL) and the EZSync
clock synchronization (SYNC) function. Most device
settings and operating modes are controlled through the
SPI bus.
To minimize power consumption, many sections of the
LTC6954 can be powered down when not in use. As shown
in Figure 2, the LTC6954 can be used as an independent
clock distribution part. Any unused outputs from the clock
distribution section may be powered down.
Figure 3 highlights an LTC6950 driving the LTC6954. This
example shows a single LTC6954 device, but each output
from the LTC6950 can drive a separate LTC6954 device
for support of up to five LTC6954 devices. The effortlessto-use EZSync multipart synchronization feature assures
consistent edge alignment of all outputs from all devices.
See the EZSync Clock Output Synchronization section for
more details on EZSync operation.
0.1µF
49.9Ω
3.3V
V+
IN+
LTC6954-x
IN–
49.9Ω
49.9Ω
SYNC
SYNC
CONTROL
OUT0SEL
OUT1SEL
OUT2SEL
SDO
SPI
SERIAL
PORT
SDI
SERIAL
PORT
AND
DIGITAL
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
OUT0+
OUT0–
OUT1+
OUT1–
OUT2+
OUT2–
SCLK
CS
GND
6954 F02
Figure 2. The LTC6954 Connected as an Independent Clock Distribution Part
6954f
24
For more information www.linear.com/LTC6954
LTC6954
Operation
0.1µF
0.1µF 3.3V
REF
OSC
49.9Ω
–
REF
VCP+
V+
REF+
R DIVIDER
49.9Ω
5V
N DIVIDER
PHASE
FREQUENCY
DETECTOR
LTC6950
VCO
CP
CHARGE
PUMP
CP
49.9Ω
RZ
CI
VCO+
49.9Ω
VCO–
SYNC
SYNC
SYNC
CONTROL
STAT2
STAT1
SDO
SDI
SERIAL
PORT
SCLK
CS
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
49.9Ω
PECL0+
PECL0–
49.9Ω
PECL1+
TO DATA ACQUISITION,
FPGA, ASICs
PECL1–
PECL2+
PECL2–
PECL3+
PECL3–
LV/CM+
LV/CM–
TO FPGA, ASICs
GND
0.1µF 3.3V
100Ω
V+
IN+
LTC6954-X
IN–
SYNC
SYNC
CONTROL
OUT0SEL
OUT1SEL
3.3V
OUT2SEL
SDO
SPI
SERIAL
PORT
SDI
SERIAL
PORT
AND
DIGITAL
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
OUT0+
OUT0–
OUT1+
TO DATA ACQUISITION,
FPGA, ASICs
OUT1–
OUT2+
OUT2–
SCLK
CS
GND
6954 F03
Figure 3. The LTC6950 in Controller Mode Clocking an LTC6954.
For Best Performance Use One of the LVPECL Outputs From the LTC6950 (with the IBIAS Enabled) to
Clock the LTC6954. All Outputs From Both Devices Are Easily Synchronized by Applying a 1ms (Min)
Wide Pulse on the SYNC Pins.
6954f
For more information www.linear.com/LTC6954
25
LTC6954
Operation
INPUT BUFFER
OUTPUT DIVIDER (M)
The LTC6954’s input buffer (IN+, IN–) provides a flexible
interface to either differential or single-ended frequency
sources. The maximum input signal frequency is 1.4GHz
(1.8GHz for the LTC6954-1 when DELx = 0). Differential
signals may be applied directly to the input as long as the
signal swing is less than 1.5VP-P to avoid turning on the
input protection diodes (see Figure 4).
Each clock distribution path includes a 6-bit output (M)
divider that reduces the input frequency by the programmed
divide modulus, M. By programming the Mx[5:0] bits for
each output divider, the divide modulus is set to any integer
from 1 to 63, inclusive. Circuitry within the output divider
ensures the output duty cycle will always be 50% for a
programmed divide modulus greater than 1. When the
output divider has been programmed for a divide modulus
of 1 or 0, the output duty cycle will be the same as the input
and the output divider is bypassed and powered down.
See Table 2 for a summary of the registers containing the
output divider control bits for each clock output distribution path. See Table 6, Serial Port Register Mapping, for
complete register mapping information.
It is also important that the IN± inputs be low noise and
have a slew rate of at least 100V/µs. See the Applications
Information section for more information on IN signal
requirements and interfacing.
BIAS
VIN+
VIN+
2.05V
1.2k
27
Table 2. Output (M) Divider Control Registers
1.2k
CLOCK
OUTPUT
IN+
OUT0
28
IN–
DIVIDE
MODULUS
BITS
REG ADDR
(HEX)
M0
[5:0]
h02
OUT1
M1
[5:0]
h04
OUT2
M2
[5:0]
h06
6954 F04
INPUT CLOCK CYCLE DELAY (DEL)
Figure 4. Simplified IN± Input Schematic
CLOCK DISTRIBUTION
The LTC6954 provides low noise clock distribution capability via three low skew distribution paths. Each distribution path includes an output divider, an input clock cycle
delay block and an output driver. The output driver can
be LVPECL, LVDS or CMOS compatible depending on
which LTC6954 part is selected and the configuration of
the corresponding OUTxSEL pin.
Each clock distribution path includes a 6-bit input cycle
delay block, which is used in conjunction with the synchronization input pin, SYNC, to force phase alignments of the
various clock outputs. When the SYNC input de-asserts,
the delay block begins counting input clock cycles. When
the count reaches the programmed configuration for each
path, the output driver begins transitioning. To save power,
the input cycle delay block powers down when all output
phase alignments are complete.
The number of cycles of delay adjustment allowed for each
output may be any integer from 0 to 63, inclusive, and is
configured by enabling the specific delay block and then
directly programming the number of delay cycles into
the appropriate DELx[5:0] bits. Setting the SYNC_ENx
bit to 1 enables each delay block. Alternatively, setting
SYNC_ENx to 0 results in the selected cycle delay block
being bypassed and powered down.
6954f
26
For more information www.linear.com/LTC6954
LTC6954
Operation
Because the input clock cycle delay block operates independently of the output divider block, the programmed
cycle delay adjustment occurs regardless of the modulus
setting of the output divider (see the example in Figure 5).
0
1
2
3
4
5
6
7
8
9 10 11
IN
1 INPUT CYCLE
OUT0
1 INPUT CYCLE DELAY
OUT1
11 INPUT CYCLE DELAY
OUT2
6954 F05
SYNC DE-ASSERTED EARLIER
LVDS/CMOS OUTPUT DRIVER
The LTC6954-2/LTC6954-3/LTC6954-4 have the capability
to provide one or more LVDS or CMOS outputs. Connecting
the corresponding output’s OUTxSEL pin to VA+enables
LVDS compatible operation at frequencies up to 1.4GHz,
while connecting it to GND configures two CMOS compatible output drivers with a maximum operating frequency
of 250MHz.
When the output driver is configured for CMOS operation,
programming the bit CMSINVx to 1 inverts the OUT – relative to OUT +. Setting CMSINVx to 0 results in both OUT+
and OUT – being in phase. See Table 4 for a summary of
the registers containing the CMOS phase control bits for
each clock output distribution path.
Table 4. CMOS Phase-Select Registers
Figure 5. Input Clock Delay Operation
(M0 = M1 = M2 = 4, DEL0 = 0, DEL1 = 1, DEL2 = 11)
Refer to the EZSync Clock Output Synchronization section
for more information about using the SYNC input pin to
achieve specific output phase alignments.
See Table 3 for a summary of the registers containing the output delay control bits for each clock output
distribution path. For complete register mapping information, see Table 6, Serial Port Register Mapping.
Table 3. Output Delay (DEL) Control Registers
CLOCK
OUTPUT
OUTPUT
DELAY
BITS
SYNC
ENABLE
BIT
REG ADDR
(HEX)
OUT0
DEL0
[5:0]
SYNC_EN0
[7]
h01
OUT1
DEL1
[5:0]
SYNC_EN1
[7]
h03
OUT2
DEL2
[5:0]
SYNC_EN2
[7]
h05
CLOCK
OUTPUT
OUT0
BIT
DESCRIPTOR
BIT
REG ADDR
(HEX)
CMSINV0
[6]
h01
OUT1
CMSINV1
[6]
h03
OUT2
CMSINV2
[6]
h05
When the output is configured for LVDS operation, the
output driver can be further configured for different output current modes using the LVCSx bits. See Table 5 for
a summary of the registers containing the LVDS current
settings. The higher current setting is ideal for applications
where the LVDS output driver is double-terminated. For
example, if the LVDS output is terminated at the near end
with a differential 100Ω resistor and at the far end with
a differential 100Ω resistor, programming LVCS for 7mA
operation will allow full LVDS swings. See the Applications
Information section for LVDS and CMOS output driver
interface circuits.
Table 5. LVDS Current Settings
CLOCK OUTPUT
OUT0
OUT1
OUT2
BIT DESCRIPTOR
BIT
REG ADDR (HEX)
VALUE
ILVDS
DIFFERENTIAL TERMINATION
LVCS0
[6]
h02
0
3.5mA
100Ω
1
7mA
50Ω (100Ω || 100Ω)
0
3.5mA
100Ω
1
7mA
50Ω (100Ω || 100Ω)
0
3.5mA
100Ω
1
7mA
50Ω (100Ω || 100Ω)
LVCS1
LVCS2
[6]
[6]
h04
h06
6954f
For more information www.linear.com/LTC6954
27
LTC6954
Operation
LVPECL OUTPUT DRIVER
The LTC6954-1/LTC6954-2/LTC6954-3 have the capability to provide one or more low noise, low skew LVPECL
compatible output drivers depending on the part version
selected. The output drivers are designed to operate at
frequencies up to 1.4GHz (1.8GHz for the LTC6954-1
when DELx = 0). The outputs also provide considerable
flexibility for biasing and termination. Internal biasing for
the output emitter followers may be selected by setting
the OUTxSEL pin to VA+ for the appropriate output driver
block. See Figure 6 for a simplified schematic.
Enabling the internal bias will usually reduce the number
of passive components required off-chip. In many cases, a
single 100Ω differential termination at the far end is all that
is required. In addition, more symmetrical rise/fall times
may result from using the constant current internal bias.
Setting OUTxSEL to 0 disables the internal bias and allows
the LVPECL output driver to be configured using standard
LVPECL bias and termination networks. See the Applications Information section for more information about
recommended bias and termination networks.
EZSync CLOCK OUTPUT SYNCHRONIZATION
The LTC6954 allows easy synchronization of the rising
edges of clock outputs from a single independent part
by simply pulsing the CMOS logic compatible SYNC
input pin.
VOUTx+
Multiple part synchronization is also easily achieved
by driving the LTC6954’s IN± input with one of Linear
Technology’s EZSync control mode capable drivers, such
as the LTC6950. Using an EZSync control mode part as
the driver, synchronization of its outputs and up to five
LTC6954 parts is also as easy as pulsing the parts’ SYNC
input pins. There are no precision timing requirements for
this pulse. The EZSync Controller part provides all of the
precision timing.
SINGLE PART, INDEPENDENT SYNCHRONIZATION
To synchronize the rising edges of the outputs of a single,
independent LTC6954, a CMOS logic pulse of at least 1ms
duration is required on the SYNC input.
Each synchronized clock output should be sync-enabled,
by programming its SYNC_ENx bit to 1. Programming an output to be sync-enabled results in that clock
output being gated, or noncontinuous, during the
synchronization process. Therefore, clock outputs that
must not be disturbed (gated) during a synchronization
operation should have their SYNC_ENx bits programmed
to 0.
A synchronization operation is performed by forcing the
SYNC input (Pin 22) to a logic HIGH for at least 1ms. The
LTC6954 then retimes the SYNC input with respect to the
VOUTx+
OUT+
OUT –
IBIAS
IBIAS
6954 F06
Figure 6. Simplified LVPECL Output Schematic
6954f
28
For more information www.linear.com/LTC6954
LTC6954
Operation
input signal to create an internal SYNC_RET signal, as
shown in Figure 7. When SYNC_RET transitions HIGH,
all sync-enabled clock outputs remain LOW once they
transition to that state. Note that the LTC6954 has circuitry
to prevent runt pulses, even during a synchronization
operation, so the clock outputs only transition LOW when
they would do so normally. Once the internal SYNC_RET
signal transitions LOW, all sync-enabled outputs transition
HIGH simultaneously, and the synchronization operation
is complete.
By programming the delay bits, DELx[5:0], the LTC6954
may also provide clock outputs with phase relationships
other than synchronized first rising edges. When DELx[5:0]
are programmed, each sync-enabled output may be independently configured to wait up to 63 additional input
clock cycles before rising, relative to the 0 delay case. For
example, assuming the OUT0 and OUT1 outputs are both
configured to divide by four, programming DEL0[5:0] to 0
and DEL1[5:0] to 1 allows the outputs to have a quadrature
relationship once a synchronization operation completes
(see Figure 8). To conserve power, the input cycle delay
circuitry is turned off after a synchronization completes.
IN
SYNC_RET
…
…
OUT0
…
OUT1
…
6954 F08
Figure 8. Synchronization to Obtain I/Q Clocks,
SYNC_EN0 = SYNC_EN1 = 1, M0[5:0] = M1[5:0] = 4,
DEL0[5:0] = 0, DEL1[5:0] = 1
0.1µF 3.3V
REF
OSC
IN+
V+
IN–
LTC6954-X
SYNC
SYNC
CONTROL
OUT0SEL
SYNC_RET
OUT0+
OUT0 DIVIDE AND DELAY
OUT1+
OUT1SEL
OUT2SEL
SDO
SPI
SERIAL
PORT
SDI
OUT0–
SERIAL
PORT
AND
DIGITAL
OUT1 DIVIDE AND DELAY
LV/CM DIVIDE AND DELAY
OUT2 DIVIDE AND DELAY
SYNC_EN4 = 1, FLRDRV = 0
OUT1–
OUT2+
OUT2–
SCLK
CS
GND
6954 F07
Figure 7. SYNC_RET Propagation
6954f
For more information www.linear.com/LTC6954
29
LTC6954
Operation
MULTIPLE PART SYNCHRONIZATION
Multiple LTC6954 parts may be easily configured to provide
more synchronized outputs than are available on a single
part provided that the parts are all driven by an EZSync
controller part.
All parts being synchronized should share a common
SYNC input, but there is no requirement for precise timing of this signal between the different parts. The only
requirements are the skew of the SYNC pulse between
the different parts is no greater than 10μs, and the SYNC
pulse is at least 1ms in duration.
The general concept behind synchronizing multiple parts
is to have one part as the EZSync “controller,” while all
other parts are “followers.” The controller part controls the
timing of all parts because it provides gated clock inputs
to all follower parts. By providing an appropriate gated
clock signal to each follower part, the controller ensures
the outputs of all follower parts will have their first rising
edge synchronized.
Furthermore, any output of the controller part not being
used as a follower-driver may be configured to be followersynchronous, which forces its output to have a first rising
edge synchronized with all follower parts’ outputs.
The LTC6954 is not capable of control mode operation. It
can only be used as a follower. Parts such as the LTC6950
are capable of control or follow mode. With five outputs
available, the LTC6950 can control and drive up to five follower devices. These followers may be additional LTC6950
parts, LTC6954 parts or any combination of each part.
The EZSync feature allows easy multipart synchronization
of rising clock edges, so outputs of multiple parts will have
a repeatable phase alignment. EZSync does not guarantee
absolute time synchronization. That is, EZSync makes
input cycle delay adjustments only, so any PCB trace delay
from the controller to the follower, plus the propagation
delay of the follower device, will be reflected as a delta in
absolute time between the follower and controller when
measured at their respective output pins.
The simplest configuration for synchronizing multiple EZSync compatible parts is shown in Figure 9. The
LTC6950 has its SYNCMD[1:0] bits programmed to control mode. Because the PECL0 output of the LTC6950 is
used as an input to the LTC6954, the LTC6950 should be
configured to make that output a follower-driver, which
is accomplished by programming FLDRV0 to 1.
To configure the PECL1, PECL2, PECL3 and LV/CM outputs
of the LTC6950 as follower-synchronous, an internal VCO
cycle delay cell must be enabled, which is accomplished by
programming the FLDRV1, FLDRV2, FLDRV3 and FLDRV4
bits to 0. All outputs should have their SYNC_ENx bits
programmed to 1 to allow synchronization. If there is an
output which should not be disturbed (gated), program
its SYNC_ENx bit to 0.
The example in Figure 9 makes an arbitrary choice of using
the PECL0 differential outputs to drive the LVPECL compatible input of the LTC6954. Any of the outputs from the
LTC6950 may be used as long as the appropriate FLDRVx
bit is programmed to 1.
All LTC6954 outputs that are to be synchronized must have
its SYNC_ENx bit programmed to 1. As noted earlier, if
there is an output which should not be disturbed (gated),
program its SYNC_ENx bit to 0.
6954f
30
For more information www.linear.com/LTC6954
LTC6954
Operation
0.1µF 3.3V
REF
OSC
V+
REF+
REF–
R DIVIDER
PHASE
FREQUENCY
DETECTOR
SYNC_RET
STAT2
SDO
SERIAL
PORT
SDI
PECL0 DIVIDE AND DELAY
SYNC_EN0 = 1, FLRDRV = 1
PECL2 DIVIDE AND DELAY
SYNC_EN2 = 1, FLRDRV = 0
SCLK
PECL3 DIVIDE AND DELAY
SYNC_EN3 = 1, FLRDRV = 0
CS
LV/CM DIVIDE AND DELAY
SYNC_EN4 = 1, FLRDRV = 0
GND
VCO
CP
CHARGE
PUMP
VCO–
PECL1 DIVIDE AND DELAY
SYNC_EN1 = 1, FLRDRV = 0
STAT1
LTC6950
VCO+
SYNC
RETIME
CONTROL
SYNC
5V
VCP+
N DIVIDER
SYNC
0.1µF
PECL0+
PECL0–
PECL1+
PECL1–
PECL2+
PECL2–
PECL3+
PECL3–
LV/CM+
LV/CM–
0.1µF 3.3V
100Ω
V+
IN+
IN–
SYNC
SYNC
CONTROL
SYNC_RET
OUT0 DIVIDE AND DELAY
SYNC_EN0 = 1
OUT0SEL
OUT1SEL
OUT2SEL
SDO
SPI
SERIAL
PORT
SDI
SERIAL
PORT
AND
DIGITAL
OUT1 DIVIDE AND DELAY
SYNC_EN1 = 1
OUT2 DIVIDE
LV/CM
DIVIDE AND
AND DELAY
DELAY
SYNC_EN2
=1 =0
SYNC_EN4
= 1, FLRDRV
LTC6954-X
OUT0+
OUT0–
OUT1+
OUT1–
OUT2+
OUT2–
SCLK
CS
GND
6954 F09
Figure 9. LTC6950 Controller Part Driving an LTC6954 Follower Part.
The PECL0 Output of the LTC6950 Drives the LTC6954 Input. All Other LTC6950 Outputs Are Programmed as
Follower-Synchronous, Enabling All Seven Outputs to Be Rising Edge Synchronized
6954f
For more information www.linear.com/LTC6954
31
LTC6954
Operation
The timing diagram in Figure 10 illustrates multipart
output synchronization of the circuit shown in Figure 9.
The configurations of both the LTC6950 (controller) and
the LTC6954 (follower) are as described in the preceding
paragraphs. Figure 10 highlights that once the SYNC input
transitions to a logic low, both outputs of the LTC6954
(LTC6954.OUT0 and LTC6954.OUT1) have their first rising
edges aligned with each other, as well as with the followersynchronous output of the LTC6950 (LTC6950.PECL1).
EZSync control mode parts have numerous timing details
available including clock synchronization to not only the
VCO
SYNC
…
…
…
…
VCO input, but also synchronization to the PLL’s feedback
N divider. This allows for synchronization to the reference
frequency when the controller’s PLL is locked. Consult the
data sheet for the EZSync controller part (e.g., LTC6950)
for the details of control mode operation.
As illustrated in Figure 9 and Figure 10, the EZSync feature
allows a device configured in control mode to generate
appropriately gated clock signals that guarantee all devices
in follow mode will be synchronized with each other and
with any follower-synchronous outputs of the controller,
making multipart synchronization easy.
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
LTC6954.OUT0
…
…
…
…
LTC6954.OUT1
…
…
…
…
LTC6950.SYNC_RET
…
LTC6950.PECL0
…
LTC6950.PECL1
LTC6954.SYNC_RET
…
…
EDGE SYNCHRONIZED
6954 F10
Figure 10. Timing Diagram of Circuit Shown in Figure 9 with Edge Synchronized Outputs Highlighted;
LTC6950: M0[5:0] = 1, M1[5:0] = 4, DEL1[5:0] = 0, FLDRV0 = 1, FLDRV1 = 0, SYNC_EN0 = SYNC_EN1 = 1,
LTC6954: M0[5:0] = 4, M1[5:0] = 4, DEL0[5:0] = DEL1[5:0] = 0, SYNC_EN0 = SYNC_EN1 = 1
6954f
32
For more information www.linear.com/LTC6954
LTC6954
Operation
SERIAL PORT
Data is read from the part during a communication burst
using SDO. Read back may be multidrop (more than one
LTC6954 connected in parallel on the serial bus), as SDO
is set to a high impedance (Hi-Z) when CS is HIGH or when
data is not being read from the part. If the LTC6954 is
not used in a multidrop configuration, or if the serial port
master is not capable of setting the SDO line level between
read sequences, attaching a high value resistor of at least
200k between SDO and GND to ensure the line returns to
a known level during Hi-Z states is highly recommended.
See Figure 12 for details.
The LTC6954 SPI-compatible serial port provides chip
control.
COMMUNICATION SEQUENCE
The serial bus is comprised of chip select (CS), serial clock
(SCLK), serial data input (SDI) and serial data output (SDO)
signals. Data transfers to the LTC6954 are accomplished
by the serial bus master device first taking CS LOW, which
enables the LTC6954’s serial port. Input data applied on
SDI is clocked on the rising edge of SCLK, with most
significant bits transferred first. The communication burst
is terminated by the serial bus master device returning CS
HIGH. See Figure 11 for details.
MASTER–CS
tCSS
tCKL
tCKH
tCSS
tCSH
MASTER–SCLK
tCS
MASTER–SDI
tCH
DATA
DATA
6954 F11
Figure 11. Serial Port Write Timing Diagram
MASTER–CS
8TH CLOCK
MASTER–SCLK
tDO
LTC6954–SDO
Hi-Z
tDO
DON’T CARE
tDO
tDO
DATA
DATA
Hi-Z
6954 F12
Figure 12. Serial Port Read Timing Diagram
6954f
For more information www.linear.com/LTC6954
33
LTC6954
Operation
SINGLE BYTE TRANSFERS
The serial port is arranged in a straightforward memory
map, with status and control available in eight bytewide registers. All data bursts are comprised of at least
two bytes. The seven most significant bits (MSB) of the
first byte are the register address, with a least significant
bit (LSB) of 1 indicating a read from the part, and an LSB
of 0 indicating a write to the part. The subsequent byte,
or bytes, is data from/to the specified register address.
See Figure 13 for an example of a detailed write sequence,
and Figure 14 for a read sequence.
master device contains a first byte of data on SDI that
includes the 7-bit destination register address (Addr0) and
an LSB of 0 indicating a write operation. The second byte
on SDI is the data to be written into address Addr0. To
terminate the first communication burst, CS is taken HIGH.
The second communication burst is structured the same
way as the first. The first byte on SDI contains a 7-bit
destination register address (Addr1) and an LSB of 0 to
indicate a write operation. The next byte on SDI is the data
intended for the register at address Addr1. And finally,
the transfer is terminated by taking CS HIGH.
Figure 15 shows an example of two write communication
bursts. The first communication burst from the serial bus
MASTER–CS
16
CLOCKS
MASTER–SCLK
7-BIT REGISTER ADDRESS
MASTER–SDI
8 BITS OF DATA
A6 A5 A4 A3 A2 A1 A0 0 D7 D6 D5 D4 D3 D2 D1 D0
0 = WRITE
Hi-Z
LTC6954–SDO
6954 F13
Figure 13. Serial Port Write Sequence
MASTER–CS
16 CLOCKS
MASTER–SCLK
7-BIT REGISTER ADDRESS
MASTER–SDI
1 = READ
A6 A5 A4 A3 A2 A1 A0 1
8 BITS OF DATA
LTC6954–SDO
Hi-Z
X D7 D6 D5 D4 D3 D2 D1 D0 DX
Hi-Z
6954 F14
Figure 14. Serial Port Read Sequence
6954f
34
For more information www.linear.com/LTC6954
LTC6954
Operation
MULTIPLE BYTE TRANSFERS
More efficient data transfer of multiple bytes is accomplished by using the LTC6954’s register address autoincrement feature, as shown in Figure 16. Like Figure 15,
Figure 16 shows the serial bus master device sending the
destination register address and an LSB of 0 in the first
byte, followed by a second byte of data for that destination
register. But instead of terminating the burst by taking CS
back HIGH, the serial port master device continues sending
bytes destined for subsequent registers. Byte 1’s destination address is Addr0+1, Byte 2’s destination address is
Addr0+2 and so on. If the register address pointer attempts
to increment past 7 (h07), it is automatically reset to 0.
An example of an auto-increment read from the part is
shown in Figure 17. The first byte of the burst from the
serial bus master device contains the 7-bit destination
register address (Addr0) and an LSB of 1 to indicate a
read operation. Once the LTC6954 detects a read burst,
it takes SDO out of the Hi-Z condition and begins to send
data bytes sequentially, starting with data from register
Addr0. The part ignores all other data on SDI until the
burst is terminated by taking CS HIGH.
MASTER–CS
Addr0 + Wr
MASTER–SDI
LTC6954–SDO
Byte 0
Addr1 + Wr
Byte 1
Hi-Z
6954 F15
Figure 15. Serial Port Single Byte Write
MASTER–CS
Addr0 + Wr
MASTER–SDI
LTC6954–SDO
Byte 0
Byte 1
Byte 2
Hi-Z
6954 F16
Figure 16. Serial Port Auto-Increment Write
MASTER–CS
Addr0 + Rd
MASTER–SDI
LTC6954–SDO
Hi-Z
DON’T CARE
Byte 0
Byte 1
Hi-Z
Byte 2
6954 F17
Figure 17. Serial Port Auto-Increment Read
6954f
For more information www.linear.com/LTC6954
35
LTC6954
Operation
MULTIDROP CONFIGURATION
BLOCK POWER-DOWN
Several LTC6954’s may share the serial bus. In this
multidrop configuration SCLK, SDI and SDO are common between all parts. The serial bus master must use a
separate CS for each LTC6954 and ensure that only one
device has CS asserted at any time. It is recommended to
attach a high value resistor from SDO to GND to ensure
the line returns to a known level during Hi-Z states.
The LTC6954 provides considerable flexibility to power
down unused blocks. A summary of power-down bits
is shown in Table 7. To determine the power savings in
shutting down a particular section, consult the Supply
Current Delta area of the Electrical Characteristics section.
SERIAL PORT REGISTERS
The LTC6954’s memory map is shown in Table 6. Detailed
bit descriptions are shown in Table 8.
As noted earlier, to achieve maximum power savings when
an LVPECL output is unused and powered down, it is recommended that no terminations or other bias circuitry be
connected to the output driver pins.
Table 7. Block Power-Down Descriptions
BIT NAME
DESCRIPTION
PDALL
Power-Down Whole Chip
PD_OUT2
Power-Down OUT2 Output Driver
PD_DIV2
Power-Down OUT2 Output Driver and Output Divider
PD_OUT1
Power-Down OUT1 Output Driver
PD_DIV1
Power-Down OUT1 Output Driver and Output Divider
PD_OUT0
Power-Down OUT0 Output Driver
PD_DIV0
Power-Down OUT0 Output Driver and Output Divider
Table 6. LTC6954 Serial Port Register Mapping
ADDR
(HEX)
[7] MSB
[6]
[5]
[4]
[3]
[2]
[1]
[0] LSB
R/W
DEFAULT
(HEX)
h00
*
PDALL
PD_OUT2
PD_DIV2
PD_OUT1
PD_DIV1
PD_OUT0
PD_DIV0
R/W
h00
h01
SYNC_EN0
CMSINV0
DEL0[5]
DEL0[4]
DEL0[3]
DEL0[2]
DEL0[1]
DEL0[0]
R/W
hC0
h02
*
LVCS0
M0[5]
M0[4]
M0[3]
M0[2]
M0[1]
M0[0]
R/W
h02
h03
SYNC_EN1
CMSINV1
DEL1[5]
DEL1[4]
DEL1[3]
DEL1[2]
DEL1[1]
DEL1[0]
R/W
hC0
h04
*
LVCS1
M1[5]
M1[4]
M1[3]
M1[2]
M1[1]
M1[0]
R/W
h04
h05
SYNC_EN2
CMSINV2
DEL2[5]
DEL2[4]
DEL2[3]
DEL2[2]
DEL2[1]
DEL2[0]
R/W
hC0
h06
*
LVCS2
M2[5]
M2[4]
M2[3]
M2[2]
M2[1]
M2[0]
R/W
h08
h07
REV2
REV1
REV0
PART4
PART3
PART2
PART1
PART0
R
h2X
*Unused
6954f
36
For more information www.linear.com/LTC6954
LTC6954
Operation
Table 8. Serial Port Register Bit Descriptions
NAME
DESCRIPTION
BIT(s)
DEFAULT
VALUE
(b: BINARY
h: HEX)
CMSINV0
CMOS Output Phase Relationship on OUT0. IF CMSINV0 = 0, Then OUT0+ and OUT0– Are
In-Phase; If CMSINV0 = 1, Then OUT0+ and OUT0– Are Inverted Relative to the Other.
Ignore if Configured for LVPECL or LVDS.
h01[6]
R/W
b1
CMSINV1
CMOS Output Phase Relationship on OUT1. IF CMSINV1 = 0, Then OUT1+ and OUT1– Are
In-Phase; If CMSINV1 = 1, Then OUT1+ and OUT1– Are Inverted Relative to the Other.
Ignore if Configured for LVPECL or LVDS.
h03[6]
R/W
b1
CMSINV2
CMOS Output Phase Relationship on OUT2; IF CMSINV2 = 0, Then OUT2+ and OUT2– Are
In-Phase; If CMSINV2 = 1, Then OUT2+ and OUT2– Are Inverted Relative to the Other.
Ignore if Configured for LVPECL or LVDS.
h05[6]
R/W
b1
DEL0[5:0]
Sets the OUT0 Delay Value, 0 ≤ DEL0[5:0] ≤ 63 Input Clock Cycles.
h01[5:0]
R/W
h00
REG
ADDR
(HEX)
DEL1[5:0]
Sets the OUT1 Delay Value, 0 ≤ DEL1[5:0] ≤ 63 Input Clock Cycles.
h03[5:0]
R/W
h00
DEL2[5:0]
Sets the OUT2 Delay Value, 0 ≤ DEL2[5:0] ≤ 63 Input Clock Cycles.
h05[5:0]
R/W
h00
LVCS0
Sets the LVDS Output Current for OUT0, (0 = 3.5mA,1 = 7mA).
Ignore if the Output Is LVPECL or CMOS.
h02[6]
R/W
b0
LVCS1
Sets the LVDS Output Current for OUT1, (0 = 3.5mA,1 = 7mA).
Ignore if the Output Is LVPECL or CMOS.
h04[6]
R/W
b0
LVCS2
Sets the LVDS Output Current for OUT2, (0 = 3.5mA,1 = 7mA).
Ignore if the Output Is LVPECL or CMOS.
h06[6]
R/W
b0
M0[5:0]
M0[5:0] Sets the OUT0 Output Divider Modulus to Any Integer From 1 to 63.
Programming M0[5:0] to a Value of Hex 0 or 1 Results in a Divide Modulus of 1.
h02[5:0]
R/W
h02
M1[5:0]
M1[5:0] Sets the OUT1 Output Divider Modulus to Any Integer From 1 to 63.
Programming M1[5:0] to a Value of Hex 0 or 1 Results in a Divide Modulus of 1.
h04[5:0]
R/W
h04
M2[5:0]
M2[5:0] Sets the OUT2 Output Divider Modulus to Any Integer From 1 to 63.
Programming M2[5:0] to a Value of Hex 0 or 1 Results in a Divide Modulus of 1.
h06[5:0]
R/W
h08
PART[4:0]
Part code (h00 = LTC6954-1, h01 = LTC6954-2, h02 = LTC6954-3, h03 = LTC6954-4).
h07[4:0]
R
PDALL
For PDALL = 1, the Full Chip Is Powered Down.
h00[6]
R/W
b0
PD_DIV0
For PD_DIV0 = 1, the OUT0 Divider and the Output Buffer Is Powered Down.
h00[0]
R/W
b0
PD_DIV1
For PD_DIV1 = 1, the OUT1 Divider and the Output Buffer Is Powered Down.
h00[2]
R/W
b0
PD_DIV2
For PD_DIV2 = 1, the OUT2 Divider and the Output Buffer Is Powered Down.
h00[4]
R/W
b0
PD_OUT0
For PD_OUT0 = 1, the OUT0 Output Buffer Is Powered Down.
h00[1]
R/W
b0
PD_OUT1
For PD_OUT1 = 1, the OUT1 Output Buffer Is Powered Down.
h00[3]
R/W
b0
PD_OUT2
For PD_OUT2 = 1, the OUT2 Output Buffer Is Powered Down.
h00[5]
R/W
b0
REV[2:0]
Part Revision Code.
h07[7:5]
R
b001
SYNC_EN0
For SYNC_EN0 = 1, the OUT0 Output Will Synchronize to the Clock Input During the SYNC
Procedure. If SYNC_EN0 = 0, Then the OUT0 Output Ignores the Input to the SYNC Pin.
h01[7]
R/W
b1
SYNC_EN1
For SYNC_EN1 = 1, the OUT1 Output Will Synchronize to the Clock Input During the SYNC
Procedure. If SYNC_EN1 = 0, Then the OUT1 Output Ignores the Input to the SYNC Pin.
h03[7]
R/W
b1
SYNC_EN2
For SYNC_EN2 = 1, the OUT2 Output Will Synchronize to the Clock Input During the SYNC
Procedure. If SYNC_EN2 = 0, Then the OUT2 Output Ignores the Input to the SYNC Pin.
h05[7]
R/W
b1
6954f
For more information www.linear.com/LTC6954
37
LTC6954
Applications Information
I/O INTERFACE
The LTC6954 is a high performance clock distribution chip.
To achieve the best performance, it is important to select
the proper circuitry to interface to the high frequency, low
noise inputs and outputs.
INPUT BUFFER
The LTC6954 provides a flexible interface to either differential or single-ended frequency sources. The maximum input signal frequency is 1.4GHz (1.8GHz for the
LTC6954-1 when DELx = 0). Any signal source may be
directly coupled (DC) to the LTC6954, as long as its signal
swing is less than 1.5VP-P and its common mode voltage
is approximately the self-bias voltage of the input buffer
(see Figure 18). If the input signal is too large, it should
be attenuated to avoid turning on the input protection
diodes. If the common mode voltage is too high or low,
the signal must be level shifted or AC-coupled.
To achieve the best noise performance, it is important
that the input frequency source have low phase noise and
a slew rate of at least 100V/µs. Additionally, the input
signal transmission line should be terminated as close to
the input pins as possible to minimize reflections. Refer to
the Electrical Characteristics table for the specified input
impedance of the LTC6954.
Common signals that may be DC-coupled into the
LTC6954’s input include 2.5V CML and 3.3V LVPECL.
Common signals that must be AC-coupled into the
LTC6954’s input include 3.3V CML, LVDS, CMOS and RF
style, 50Ω output sine wave oscillators (<7.5dBm signal).
2.5V CML and 3.3V LVPECL signals may optionally be
AC-coupled if system design considerations require it.
Figure 19 shows many common IN± input signal interfaces. Note that all signal traces are assumed to be 50Ω
transmission lines.
BIAS
VIN+
VIN+
2.05V
1.2k
27
28
1.2k
IN+
IN–
6954 F18
Figure 18. Simplified IN Input Schematic
6954f
38
For more information www.linear.com/LTC6954
LTC6954
Applications Information
SINE WAVE
OSCILLATOR
50Ω OUTPUT
IN+
ZO
ZO
PI
ATTENUATOR
49.9Ω
IN+
49.9Ω
LTC6954
LTC6954
49.9Ω
49.9Ω
IN –
49.9Ω
IN –
49.9Ω
AC-COUPLED RF SINE WAVE OSCILLATOR, OUTPUT >7.5dBm
AC-COUPLED RF SINE WAVE OSCILLATOR, OUTPUT ≤7.5dBm
IN+
ZO
IN+
ZO
2.5V
CML
100Ω
3.3V
LVPECL
LTC6954
ZO
150Ω
IN –
ZO
IN
–
150Ω
DC-COUPLED 2.5V CML
AC-COUPLED 3.3V LVPECL
IN+
ZO
49.9Ω
3.3V
LVPECL
IN+
ZO
5V
PECL
LTC6954
100Ω
49.9Ω
IN –
330Ω
LTC6954
IN –
ZO
ZO
150Ω
LTC6954
100Ω
330Ω
150Ω
DC-COUPLED 3.3V LVPECL
AC-COUPLED 5V PECL
PREFERRED IMPLEMENTATION
ZO
IN+
ZO
IN –
3.3V
LVPECL
LTC6954
49.9Ω
IN+
ZO
3.3V CML
2.5V CML
100Ω
ZO
LTC6954
IN –
49.9Ω
AC-COUPLED 2.5V/3.3V CML
46.4Ω
ALTERNATIVE DC-COUPLED 3.3V LVPECL
IN+
ZO
LVDS
100Ω
ZO
LTC6954
IN –
6954 F19
AC-COUPLED LVDS
Figure 19. Common IN± Input Interface Configurations.
All ZO Signal Traces Are 50Ω Transmission Lines. All Capacitors Are 0.1µF. All Resistors and Capacitors Are Placed as Close as Possible
to the Driver or Receiver with the Transmission Line in Between
6954f
For more information www.linear.com/LTC6954
39
LTC6954
Applications Information
LVPECL OUTPUTS (LTC6954-1/LTC6954-2/LTC6954-3)
Disabling the internal bias, by connecting OUTxSEL to
GND, allows the LVPECL output driver to be configured
using standard LVPECL bias and termination networks.
The LTC6954 provides up to three low noise, low skew
LVPECL compatible output drivers designed for frequencies
up to 1.4GHz (1.8GHz for the LTC6954-1 when DELx = 0).
Refer to Table 9 For the output configurations available.
The output driver provides considerable flexibility for biasing and termination. Refer to Figure 20 for a simplified
schematic of the LVPECL output.
The LTC6954 allows powering down of many blocks,
including the LVPECL output drivers. When an LVPECL
output driver is powered down, the output pins will float
to approximately 0.8V below VOUTx+. Depending on the
external bias and termination circuits connected to the
LVPECL output pins, the output driver may actually source
current in this mode. To achieve maximum power savings,
it is recommended that no terminations or other bias circuitry be connected to an unused LVPECL output that will
be powered down. Additionally, if the output is expected
to be turned on and off, using the internal IBIAS with the
single 100 differential termination configuration gives the
lowest power consumption in the powered down state.
The output driver can be biased internally by setting the
appropriate OUTxSEL HIGH. Using the internal bias is
ideal for AC-coupling applications as it replaces the need
for a 150Ω resistor to ground to provide the necessary
bias for each output. It is also useful when the receiving
chip can handle 3.3V LVPECL inputs directly, then only a
100Ω differential resistor located near the receiver input
is required for proper transmission line termination.
VOUTx+
The LVPECL outputs are emitter followers and thus have
a low output impedance. LVPECL output signals also have
very fast rise and fall times. To maintain proper signal integrity (sharp rise and fall times with minimal ringing), route
signals with well controlled transmission lines with proper
far-end termination. In cases where the full LVPECL signal
swing is not required, consider using a series resistor to
provide additional near-end transmission line termination.
With both near- and far-end termination, manufacturing
variations of the transmission lines in production are more
easily tolerated. This configuration is also recommended
for driving ADCs as discussed in the “Using the LTC6954
to Clock ADC Sample Clock Inputs” section.
VOUTx+
OUT+
OUT –
OUTxSEL
OUTxSEL
6954 F20
Figure 20. Simplified LVPECL Output Schematic
Table 9.LTC6954 OUTPUT Configuration with LVPECL Outputs Highlighted
LTC6954
VERSION
OUTPUT 0
OUTPUT 1
OUTPUT 2
OUT0SEL = GND
OUT0SEL = VA+
OUT1SEL = GND
OUT1SEL = VA+
OUT2SEL = GND
OUT2SEL = VA+
LTC6954-1
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LTC6954-2
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
CMOS
LVDS
LTC6954-3
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
CMOS
LVDS
CMOS
LVDS
LTC6954-4
CMOS
LVDS
CMOS
LVDS
CMOS
LVDS
6954f
40
For more information www.linear.com/LTC6954
LTC6954
Applications Information
Figure 21 shows how to interface the LVPECL outputs to
many typical input receivers. Driving an LVDS input is a
somewhat special case. Most LVDS inputs are designed to
accept a wide range of input signal swings and common
mode levels. For many LVDS inputs, a simple connection is fine. For LVDS inputs operating on a lower power
supply voltage, a 1.2V common mode level is required.
This requirement is easily met by using a few resistors
LVPECL+
to level-shift the signal from 1.85V down to 1.2V. In this
configuration, the signal’s peak-to-peak amplitude is also
reduced, but the LVPECL signal is much larger than the
LVDS signal (1600mVP-PDIFF vs 750mVP-PDIFF) so the
signal at the LVDS receiver is at the correct level for both
the common mode level and the voltage swing. As a side
benefit, this configuration also provides both near and
far-end transmission line termination.
LVPECL+
ZO
54.9Ω
ZO
49.9Ω
100Ω
LTC6954
LVPECL–
3.3V CML
2.5V CML
3.3V LVPECL
LTC6954
LVPECL–
ZO
95.3Ω
DC-COUPLED INTO A 2.5V/3.3V CML, 3.3V LVPECL
(LVPECL INTERNAL IBIAS ENABLED)
ZO
95.3Ω
DC-COUPLED INTO AN LVDS OR AN ADC WITH A 1.2V
COMMON MODE LEVEL (LVPECL INTERNAL IBIAS DISABLED)
PREFERRED IMPLEMENTATION
LVPECL+
49.9Ω
54.9Ω
LVPECL+
ZO
27.4Ω
ZO
49.9Ω
3.3V CML
2.5V CML
3.3V LVLVPECL
LTC6954
49.9Ω
LVPECL–
150Ω
27.4Ω
ZO
LVDS OR ADCs
THAT CAN
ACCEPT A 1.8V
COMMON MODE
LEVEL
150Ω
BACK TERMINATED DC-COUPLED INTO AN ADC THAT CAN ACCEPT
A 1.85V COMMON MODE LEVEL (LVPECL INTERNAL IBIAS ENABLED)
ZO
3.3V CML
2.5V CML
3.3V LVPECL
LTC6954
LVPECL–
100Ω
LTC6954
LVPECL–
ZO
DC-COUPLED INTO A 2.5V/3.3V CML, 3.3V LVPECL
(LVPECL INTERNAL IBIAS DISABLED)
LVPECL+
LVDS OR ADCs
WITH 1.2V
COMMON
MODE LEVEL
ZO
49.9Ω
LVPECL+
LTC6954
LVPECL–
27.4Ω
27.4Ω
ZO
100Ω
ZO
AC-COUPLED
INTO LVDS OR
ADCs WITH A
SELF-BIASED
INPUT
49.9Ω
46.4Ω
AC-COUPLED INTO AN LVDS OR AN ADC WITH A SELF-BIASED INPUT
(LVPECL INTERNAL IBIAS ENABLED)
ALTERNATIVE DC-COUPLED INTO A 2.5V/3.3V CML, 3.3V LVPECL
(LVPECL INTERNAL IBIAS DISABLED)
6954 F21
Figure 21. Common LVPECL Output Interface Configurations.
All ZO Signal Traces Are 50Ω Transmission Lines. All Capacitors Are 0.1µF. All Resistors and Capacitors Are Placed as Close as Possible to
the Driver or Receiver with the Transmission Line in Between
6954f
For more information www.linear.com/LTC6954
41
LTC6954
Applications Information
LVDS/CMOS OUTPUTS (LTC6954-2/LTC6954-3/
LTC6954-4)
part versions with LVDS/CMOS outputs and the available
OUTxSEL configurations.
The LTC6954-2/LTC6954-3/LTC6954-4 have the capability to provide one or more LVDS or CMOS outputs. See
Figure 22 and Figure 23 for simplified schematics of this
output. Connecting the corresponding output’s OUTxSEL
pin to VA+ enables LVDS compatible operation at frequencies up to 1.4GHz, while connecting it to GND configures
two CMOS compatible output drivers with a maximum
operating frequency of 250MHz. Table 10 shows the
LVDS OUTPUT MODE (OUTxSEL = VA+)
When the output is configured for LVDS operation, the
output current has two settings controlled by the LVCS
bit, as shown in Table 11. LVCSx = 0 supplies current for
100Ω differential termination and has a maximum operating
frequency of 800MHz. The termination resistor should be
located near the receiver input to reduce signal reflections.
VOUTx+
VOUTx+
OUTx+
OUTx+
V+
OUTx–
V+
OUTx–
6954 F23
6954 F22
Figure 22. Simplified LVDS/CMOS Output Schematic
(LVDS Mode, CMOS Circuit Shutdown)
Figure 23. Simplified LVDS/CMOS Output Schematic
(CMOS Mode, LVDS Circuit Shutdown)
Table 10. LTC6954 Output Configuration with LVDS/CMOS Outputs Highlighted
LTC6954
VERSION
OUTPUT 0
OUTPUT 1
+
OUTPUT 2
+
OUT0SEL = GND
OUT0SEL = VA
OUT1SEL = GND
OUT1SEL = VA
OUT2SEL = GND
OUT2SEL = VA+
LTC6954-1
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LTC6954-2
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
CMOS
LVDS
LTC6954-3
LVPECL
(IBIAS is Off)
LVPECL
(IBIAS is On)
CMOS
LVDS
CMOS
LVDS
LTC6954-4
CMOS
LVDS
CMOS
LVDS
CMOS
LVDS
Table 11. LVDS Current Settings
CLOCK OUTPUT
OUT0
BIT DESCRIPTOR
BIT
REG ADDR (HEX)
VALUE
ILVDS
LVCS0
[6]
h02
0
3.5mA
100Ω
1
7mA
50Ω (100Ω || 100Ω)
0
3.5mA
100Ω
1
7mA
50Ω (100Ω || 100Ω)
0
3.5mA
100Ω
1
7mA
50Ω (100Ω || 100Ω)
OUT1
LVCS1
[6]
h04
OUT2
LVCS2
[6]
h06
DIFFERENTIAL TERMINATION
6954f
42
For more information www.linear.com/LTC6954
LTC6954
Applications Information
variations. Figure 24 shows many common LVDS output
interfaces to various logic types of inputs.
Setting LVCSx = 1 provides twice the current and enables
a maximum operating frequency of 1.4GHz. The higher
current setting (ILVDS = 7mA) is ideal for applications
where the LVDS output driver is double-terminated
(near- and far-end termination). For example, if the LVDS
output is terminated at the near end with a differential
100Ω resistor, and at the far end with a differential 100Ω
resistor, programming LVCSx = 1 for 7mA operation will
allow full LVDS swings. This configuration is properly
terminated at both ends, and is therefore more forgiving of the transmission line design and PCB production
Each LVDS output can be independently powered down
using the PD_OUTx bit. Refer to Table 6, Serial Port Register
Mapping, for the name and location of the power down
bits. When the LVDS output is powered down it will be
in a Hi-Z state.
When the LVDS/CMOS output is configured to LVDS
output mode, the CMSINVx bits are ignored. These bits
only apply to a CMOS configured output.
V+
CMOS+
10Ω
ZO
CMOS+
CMOS
LTC6954
10Ω
100Ω
ZO
CMOS
100Ω
LTC6954
CMOS–
CMOS–
CMOS OUTPUT MODE, DC-COUPLED AND DOUBLY TERMINATED INTO CMOS
(SIGNAL SWING AT THE LOAD WILL BE REDUCED)
CMOS OUTPUT MODE, DC-COUPLED INTO CMOS
WITH A SERIES SOURCE TERMINATION
(TRANSMISSION LINE SHOULD BE NO LONGER THAN 10cm)
V+
10Ω
CMOS+
100Ω
ZO
CMOS
100Ω
LTC6954
CMOS–
CMOS OUTPUT MODE, AC-COUPLED AND DOUBLY TERMINATED INTO CMOS
(SIGNAL SWING AT THE LOAD WILL BE REDUCED)
LVDS+
LTC6954
LVDS
LVDS+
ZO
LVDS
100Ω
–
LTC6954
ZO
LVDS
ZO
100Ω
–
LVDS OR ADC
100Ω
ZO
LVDS OUTPUT MODE, DC-COUPLED AND
DOUBLY TERMINATED INTO LVDS (ILVDS = 7mA)
LVDS OUTPUT MODE, DC-COUPLED AND
FAR-END TERMINATED INTO LVDS (ILVDS = 3.5mA)
3.3V
680Ω
LVDS+
ZO
LTC6954
LVDS–
680Ω
3.3V
LVPECL
CML
100Ω
ZO
1.00k
1.00k
THIS CIRCUIT WORKS WITH MANY LVPECL
RECEIVER PARTS THAT CAN ACCEPT THE
SMALLER LVDS SIGNAL SWING
(700mVP-P DIFF FOR LVDS COMPARED TO
1600mVP-P DIFF FOR LVPECL)
LVDS OUTPUT MODE, AC-COUPLED INTO LVPECL OR CML (ILVDS = 3.5mA)
6954 F24
Figure 24. Common LVDS/CMOS Output Interface Configurations.
All ZO Signal Traces Are 50Ω Transmission Lines. All Capacitors Are 0.1µF. All Resistors and Capacitors Are Placed as Close as Possible to
the Driver or Receiver with the Transmission Line in Between
6954f
For more information www.linear.com/LTC6954
43
LTC6954
Applications Information
CMOS OUTPUT MODE (OUTxSEL = GND)
POWER SUPPLIES FOR CMOS OPERATION
When the output driver is configured for CMOS operation,
programming the bit CMSINVx to 1 inverts the OUT – relative to OUT+. Setting CMSINVx to 0 results in both OUT+
and OUT – being in-phase. See Table 12 for a summary
of the registers containing the CMOS phase control bits
for each clock output distribution path.
Note that degradation of the phase noise performance
can occur if the output supply, VOUTx+, is noisy because
of additional broadband noise or discrete spectral tones.
Noise on the VOUTx+ supply will amplitude-modulate the
clock signal. This AM noise may then corrupt the spectral
purity through AM to PM conversion. However, using
the LTC6954 in LVDS mode will greatly reduce the power
supply noise coupling relative to CMOS mode, due to the
differential nature of the LVDS outputs.
CLOCK
OUTPUT
BIT
DESCRIPTOR
BITS
REG ADDR
(HEX)
OUT0
CMSINV0
[6]
h01
OUT1
CMSINV1
[6]
h03
OUT2
CMSINV2
[6]
h05
Each CMOS output can be independently powered down
using the PD_OUTx bit. Refer to Table 6, Serial Port Register Mapping, for the name and location of the power
down bits. When the CMOS output is powered down and
CMSINVx = 0 both outputs will be LOW. When CMSINVx
= 1, OUTx+ will be LOW and OUTx- will be HIGH.
When the LVDS/CMOS output is configured to CMOS
output mode, the LVCSx bits are ignored. These bits only
apply to a LVDS configured output.
While the CMOS output is rated at 250MHz, it is recommended that the LVDS output mode be used for operation at frequencies beyond 50MHz. The nature of CMOS
signaling (single-ended, large current spikes, large signal
swing, poor capacitive load driving) makes it most useful
for lower frequencies and short interconnection length. For
higher frequencies or longer interconnection lengths, LVDS
output mode is a much better choice. LVDS is designed to
drive transmission lines and its inherent differential nature
provides superior noise immunity.
When a CMOS signal is required, Figure 24 shows some
common interfaces. The use of the series termination is
the most common configuration and is suitable for short
interconnection lengths as the transmission line and the
receiver’s input capacitance will reduce the rise and fall
times. The doubly-terminated circuits suffer from reduced
signal swing at the far end and may not be acceptable with
some CMOS input circuits.
TEMPERATURE MONITOR
The LTC6954 provides an on-chip diode at Pin 31 (TEMP)
for chip temperature measurement. Pin 31 is connected
to the anode of an internal diode with its cathode connected to internal ground. The chip temperature can be
measured by injecting a constant DC current into Pin 31
and measuring its DC voltage. The voltage vs temperature
coefficient of the diode is about –1.73mV/°C with 10μA
current injected into the TEMP pin. Figure 25 shows a typical temperature voltage behavior when 10μA and 100μA
currents are injected into Pin 31.
A significant percentage of the total current used in the
LTC6954 is connected to ground through the exposed pad.
The temperature measurement provides a good indicator
that the exposed package pad has a good thermal and
electrical connection.
900
850
TEMP DIODE VOLTAGE (mV)
Table 12. CMOS Phase-Select Registers
800
750
700
650
600
100µA
10µA
550
500
450
400
–40 –20
20 40 60 80 100 120
0
JUNCTION TEMPERATURE (°C) 6954 F25
Figure 25. TEMP Diode Voltage vs Junction Temperature (TJ)
6954f
44
For more information www.linear.com/LTC6954
LTC6954
Applications Information
Use of a diode based temperature monitoring part such
as the LTC2997 is recommended for an accurate measurement. Refer to the LTC2997 Data Sheet for specific
information regarding it’s use.
If the temperature monitoring feature is not used, connect
TEMP to GND.
PCB LAYOUT GUIDELINES
The LTC6954 requires a printed circuit board (PCB) with a
clean unbroken ground plane in the first layer beneath the
part. A multilayer board with an internal ground plane is
recommended. Care must be taken when creating a PCB
layout to minimize power supply and ground inductances
and to prevent signals from interfering with each other.
Layout for the printed circuit board should ensure that
digital signals (serial port, SYNC and OUTxSEL pins) and
analog signals (all other signal pins) are separated as
much as possible. Additionally, top layer ground fill and
grounded vias should be used as barriers to isolate signals
from each other.
The LTC6954 input and all signal outputs must be routed
using transmission lines. Traces should be as short as
possible to minimize capacitance and interference pickup.
The LTC6954’s demonstration circuit, DC1954, provides
a good example of proper PCB layout. The files for this
demo circuit are found on the Linear Technology (www.
linear.com) website’s LTC6954 landing page.
and minimizes channel-to-channel crosstalk. Demo circuit
DC1954 provides a good example of good supply connections, proper bypassing and capacitor ground connections.
Bypass capacitors must be located as close to the pins as
possible and connected to ground through a low impedance
path. The traces connecting the pins and bypass capacitors must be kept short and should be made as wide as
possible. The ground connection for each capacitor must
have its own ground via and should also be connected to
the top layer ground pour.
THE EXPOSED PAD CONNECTION:
SIGNAL GROUNDING AND HEAT TRANSFER
The exposed pad on the bottom of the package is the
primary ground connection for the LTC6954 and its connection is as important as any other pin on this part. The
inductance to the ground plane must be kept to a minimum
to ensure peak performance and good signal integrity.
The exposed pad must be soldered directly to a matching
PCB land. The PCB land pattern should be connected to
the internal ground planes by an array of vias, as shown
in Figure 26. Consult the QFN Package User’s Guide on
Linear Technology website’s Packaging Information page
for specific recommendations concerning land patterns
and land via solder masks.
VIA ARRAY CONNECTS
EXPOSED PAD
18
17
16
15
14
13
19
12
SUPPLY BYPASSING
20
11
21
10
High quality ceramic bypass capacitors such as X5R, X7R
or X6S dielectrics should be used at all of the V+ supply
pins (VA+, VD+, VIN+, VOUT0+, VOUT1+ and VOUT2+). Each
pin should have its own bypass capacitor if possible. This
is easily achieved with 0201 size capacitors located on
the top side layer with the LTC6954. A good strategy is
to use 0.01µF, size 0201 capacitors, at one capacitor per
pin, on the top side of the PCB with additional 0.1µF size
0402 connected to selected pin pairs on the back side of
the PCB. This provides good, high frequency bypassing
22
9
23
8
24
7
25
6
26
5
27
4
28
3
29
2
30
1
31
32
33
34
35
36
6954 F26
Figure 26. Exposed Pad Land Pattern Highlighting the Array of
Ground Vias. Also Note Pins 14, 26, 29, 32 and 35 Are Signal
Ground and Connected Directly to the Exposed Pad Land
6954f
For more information www.linear.com/LTC6954
45
LTC6954
Applications Information
Additionally, most of the heat generated by the LTC6954
is removed from the die through the bottom side exposed
pad onto the printed circuit board. Fortunately, the previously mentioned guidelines for signal grounding also yield
the best thermal assembly and layout. Soldering of the
exposed pad to a matching PCB land provides the most
direct thermal connection. Connecting this PCB land to
all ground layers through an array of vias also is the best
way to add thermal mass and to spread the heat as much
as possible.
For best thermal transfer, the array of vias should extend
to the back side of the PCB where a sizable area of the
solder mask should be cleared to open the plated copper
directly to the air. The exposed area should be at least as
large as the land pattern on the top of the PCB. Again, demo
circuit DC1954 provides a good example of grounding the
LTC6954 from both the signal and thermal standpoints.
In a standard laboratory environment, without moving
air, demo circuit DC1954’s PCB layout yields a junction
temperature rise of about 20°C for every watt of power
dissipated.
Following the previously mentioned guidelines achieves
a good ground signal connection and a good thermal
connection. However, much of this good practice can be
undone if the ground plane has a significant void or narrowing near the part. This often occurs inadvertently when
there is a long row of adjacent signal or power vias. The
clearance around these vias can be very close to each other
or overlapping, creating a void in the plane. In extreme
cases a small ground island can form.
One area on the LTC6954 where a ground plane void could
occur is on the side of the part with the outputs OUT0
through OUT2 (Pins 1 to 12). The most difficult case is
when all three outputs are to be routed using stripline
transmission lines (transmission lines buried between
ground planes inside the PCB). Figure 27 illustrates the
issue. Using stripline transmission lines necessitates vias
to a lower layer preferably located close to each output pin.
Additionally, all of the VOUTx+ power pins require a via to
the power plane that should ideally also be located close
to each pin. As shown in Figure 27, when all of these vias
are located as close to each pin as possible (which is good
for many reasons) and in a row, there is a significant void
in the ground plane in this area. This void is undesirable
both electrically and thermally. The empty space increases
the ground inductance for the output return signal path
and decreases the flow of heat in that direction.
Figure 27 also illustrates that by pulling some of the vias
away from the part, in this case the OUTx output vias,
significant paths for current and heat flow are opened. This
is not ideal from the transmission line design standpoint,
but definitely improves the ground path inductance and
VIAS CONNECT
EXPOSED PAD
18
17
16
15
14
VIAS CONNECT
EXPOSED PAD
13
18
17
16
15
14
13
19
12
19
12
20
11
20
11
21
10
21
10
22
9
22
9
23
8
23
8
24
7
24
7
25
6
25
6
26
5
26
5
27
4
27
4
28
3
28
3
29
2
29
2
30
1
30
31
THERMAL FLOW
PATH IS BLOCKED
32
33
34
35
36
SIGNAL
RETURN
PATHS ARE
BLOCKED
GROUND
PLANE
IMPROVED
SIGNAL
RETURN
PATHS
1
31
32
33
BETTER THERMAL
FLOW PATHS
34
35
36
GROUND
PLANE
6954 F27
Figure 27. The Ground Plane Can Be Inadvertently Split by a Row of Vias Resulting in Higher Ground
Impedance and Poor Heat Transfer. Moving Some Vias or Staggering Them Fixes the Problem
6954f
46
For more information www.linear.com/LTC6954
LTC6954
Applications Information
the thermal flow. Alternatively, the VOUTx+ supply vias
could be pulled farther away from the part or a microstrip
transmission line on layer 1 of the PCB could be utilized
instead of the strip lines eliminating the need for output
vias entirely.
ADC CLOCKING AND JITTER REQUIREMENTS
Adding noise directly to a clean signal clearly reduces its
signal-to-noise ratio (SNR). In data acquisition applications, digitizing a clean signal with a noisy clock signal
also degrades the SNR. This issue is best explained in
the time domain using jitter instead of phase noise. For
this discussion, assume that the jitter is white (flat with
frequency) and of Gaussian distribution.
Figure 28 shows a sine wave signal entering a typical data
acquisition circuit composed of an ADC, an input signal
amplifier and a sampling clock. Also shown are three
signal sampling scenarios for sampling the sine wave at
its zero crossing.
In the first scenario, a perfect sine wave input is buffered
by a noiseless amplifier to drive the ADC. Sampling is
performed by a perfect, zero jitter clock. Without any added
SINE WAVE
INPUT SIGNAL
AMP
noise or sampling clock jitter, the ADC’s digitized output
value is very clearly determined and perfectly repeatable
from cycle to cycle.
In the second scenario, a perfect sine wave input is buffered by a noisy amplifier to drive the ADC. Sampling is
performed by a perfect, zero jitter clock. The added noise
results in an uncertainty in the digitized value developing
an error term which degrades the SNR. The degraded SNR
in this scenario, adding noise to the signal, is expected.
In the third scenario, a perfect sine wave input is buffered
by a noiseless amplifier to drive the ADC. Sampling is
performed by a clock signal with added jitter. Note that
as the signal is slewing, the jitter of the clock signal leads
to an uncertainty in the digitized value and an error term
just as in the previous scenario. Again, this error term
degrades the SNR.
A real world system will have both some additive amplifier noise and some sample clock jitter. Once the signal
is digitized, determining the root cause of any SNR degradation—amplifier noise or sampling clock jitter—is
often impossible.
ADC
BITS
SAMPLING CLOCK
SINE WAVE
INPUT SIGNAL WITH
NOISELESS AMP
VSAMPLE
SINE WAVE
INPUT SIGNAL WITH
NOISY AMP
∆V = VERROR
SINE WAVE
INPUT SIGNAL WITH
NOISELESS AMP
∆V = VERROR
tJ
PERFECT SAMPLING CLOCK
PERFECT SAMPLING CLOCK
6954 F28
SAMPLING CLOCK WITH ADDED JITTER
Figure 28. A Typical Data Acquisition Circuit Showing the Sampling Error
Effects of a Noisy Amplifier and a Jittery Sampling Clock
6954f
For more information www.linear.com/LTC6954
47
LTC6954
Applications Information
Degradation of the SNR due to sample clock jitter only
occurs if the input signal is slewing. If the input signal
is stationary (DC), then it does not matter when in time
the sampling occurs. Additionally, a faster slewing signal
yields a greater error (more noise) than a slower slewing
signal. Figure 29 demonstrates this effect. Note how much
larger the error term is with the fast slewing signal than
with the slow slewing signal. The conclusion is to maintain
the data converter’s SNR performance, digitization of high
input frequency signals requires a clock with much less
jitter than applications with lower frequency input signals.
FAST
SINE WAVE
SLOW
SINE WAVE
∆V = VERROR(FAST)
∆V = VERROR(SLOW)
tJ
6954 F29
Figure 29. Fast and Slow Sine Wave Signals
Sampled with a Jittery Clock
jitter is the RMS sum of the ADC’s aperture jitter and the
sample clock jitter calculated as follows:
t J(TOTAL) = t2J(CLK) + t2J(ADC)
Alternatively, for a given total jitter, the attainable SNR
limitation is calculated as follows:
SNRdB = –20 • Iog10 (2 • π • fSIG • tJ(TOTAL))
These calculations assume a full-scale sine wave input
signal. If the input signal is a complex, modulated signal
with a moderate crest factor, the peak slew rate of the
signal may be lower and the sample clock jitter requirement may be relaxed.
These calculations are also theoretical. They assume a
noiseless ADC with infinite resolution. All realistic ADCs
have both added noise and a resolution limit. The limitations
of the ADC must be accounted for to prevent overspecifying the sampling clock.
Figure 30 plots the previous equations and provides a
simple and quick way to estimate the sampling clock jitter
requirement for a given input signal or the expected SNR
performance for a given sample clock jitter.
It is important to note that the frequency of the input signal determines the sample clock’s jitter requirement. The
actual sample clock frequency does not matter. Many ADC
applications that undersample high frequency signals have
especially challenging sample clock jitter requirements.
TOTAL CLOCK
JITTER (RMS)
10fs
20fs
50fs
100fs
200fs
500fs
1ps
2ps
5ps
10ps
20ps
50ps
96
90
84
78
72
66
60
54
–SNRdB
20
t J(TOTAL) =
2 • π • fSIG
10
102
SNR (dB)
The previous discussion was useful for gaining an intuitive
feel for the SNR degradation due to sampling clock jitter.
Quantitatively, the actual sample clock jitter requirement
for a given application is calculated as follows:
108
48
10
100
1000
FREQUENCY OF FULL-SCALE INPUT SIGNAL (MHz)
6954 F30
Where fSIG is the highest frequency signal to be digitized
expressed in Hz, SNRdB is the SNR requirement in decibels
and tJ(TOTAL) is the total RMS jitter in seconds. The total
Figure 30. SNR vs Input Signal Frequency vs
Sample Clock Jitter
6954f
48
For more information www.linear.com/LTC6954
LTC6954
Applications Information
ADC SAMPLE CLOCK INPUT DRIVE REQUIREMENTS
Modern high speed, high resolution ADCs are incredibly
sensitive components able to match laboratory instruments
in many regards. With wide bandwidth and wide dynamic
range, noise or interfering signals on the analog signal
input, the voltage reference or the sampling clock input
can easily appear in the digitized data. To deliver the full
performance of any ADC, the sampling clock input must
be driven with a clean, low jitter signal.
Figure 31 shows a simplified version of a typical ADC
sample clock input. In this case, the input pins are labeled
ENC± for encode, while some ADCs label the inputs CLK±
for clock. The input is composed of a differential limiting
amplifier stage followed by a buffer that directly controls
the ADC’s track-and-hold stage.
The input amplifier requires a minimum input signal
amplitude to enter limiting. The sampling clock signal’s
amplitude should be somewhat greater than the minimum
requirement to assure that the amplifier is limiting under
all conditions, but not so large as to damage the ADC. A
typical minimum input signal level is in the 300mVP-PDIFF
to 400mVP-PDIFF range.
The sample clock input amplifier also benefits from a fast
slewing input signal as the amplifier has noise of its own.
By slewing through the crossover region quickly, the amplifier noise creates less jitter than if the transition was slow.
As shown in Figure 31, the ADC’s sample clock input is
typically differential. Although the amplifier will work fine
with a single-ended input signal, a differential sampling
clock typically delivers the best performance.
The LTC6954 meets all of these sample clock input requirements. The output signals are differential, low phase noise
(thus low jitter), have sharp rise and fall times and drive
high speed transmission lines with more than enough
signal swing.
The LTC6954’s LVPECL outputs are recommended for
the best phase noise performance. While the LVDS and
CMOS signals provide good phase noise performance, the
LVPECL outputs have the lowest phase noise.
TRANSMISSION LINES AND TERMINATION
Interconnection of high speed signaling with fast rise
and fall times requires the use of transmission lines with
properly matched termination. The transmission lines may
be stripline, microstrip or any other design topology. A
detailed discussion of transmission line design is beyond
the scope of this data sheet. Any mismatch between the
transmission line’s characteristic impedance and the
terminating impedance results in a portion of the signal
reflecting back toward the other end of the transmission
line. In the extreme case of an open- or short-circuit termination, all of the signal is reflected back.
This signal reflection leads to overshoot and ringing on
the waveform. The frequency of ringing is proportional
to the propagation delay through the transmission line,
which is mostly dependent on the length of the line. The
VDD
1.2V
ENC+
10k
ENC–
6954 G31
Figure 31. Simplified ADC Sample Clock Input Circuit
6954f
For more information www.linear.com/LTC6954
49
LTC6954
Applications Information
amplitude of the ringing is dependent on the degree of
mismatch between the transmission line’s characteristic
impedance and the termination impedance at each end of
the line. The greater the mismatch, the larger the reflection
and the greater the amplitude of the ringing. Figure 32
shows three methods of transmission line termination with
a low impedance driver and a high impedance receiver.
Near- and far-end termination is sometimes referred to
as double termination. The advantage of double termination over the simpler far-end or near-end termination is
if there is any mismatch at the far end, its reflection will
be largely absorbed by the near-end termination and the
reflected energy dies out rapidly as each re-reflected signal
is considerably smaller at each turn.
ZO
100Ω
ZO
FAR END TERMINATION
(PARALLEL OR SHUNT TERMINATION)
50Ω
50Ω
ZO
The disadvantage of double termination is that the signal level at the receiver is only half the amplitude of the
source’s signal. However, this loss of signal amplitude
is acceptable in many cases. The series resistor used in
near-end termination also adds some noise to the signal.
ZO
NEAR END TERMINATION
(SERIES TERMINATION)
50Ω
50Ω
ZO
100Ω
ZO
being re-reflected back to the receiver. The far-end receiver
is a high impedance and is poorly matched to the transmission line resulting in most of the signal being reflected
back to the driver. The termination at the source absorbs
most of this reflected signal, but if there is a mismatch in
the impedance, some of the signal is re-reflected back to
the receiver. This back-and-forth signaling continues until
the reflected signal energy eventually dies out.
6954 F32
NEAR AND FAR END TERMINATION
(DOUBLE TERMINATION)
Figure 32. Transmission Line Termination Methods (ZO = 50Ω)
Far-end termination is sometimes referred to as parallel or
shunt termination of the transmission line. Its purpose is
to match the transmission line’s impedance and prevent
signal reflection back to the driver. Any mismatch at the far
end results in a portion of the initial signal being reflected
back to the driver. As the low impedance driver is poorly
matched to the transmission line, most of this reflected
signal is re-reflected back to the receiver. This back and
forth signaling continues until the reflected signal energy
eventually dies out.
Near-end termination is sometimes referred to as series or
back termination. Its purpose is to match the transmission
line and prevent any reflected signal from the far end from
Double termination makes for a more robust and forgiving system design. Production variation of the printed
circuit board (PCB) that would affect the transmission
line’s characteristic impedance are more easily accommodated. Variation of the termination resistor value and its
nonidealities are also less critical. Delivering good signal
integrity is more easily achieved with double termination
of transmission lines at the cost of some added noise.
ADC SAMPLE CLOCK INPUT SIGNAL INTEGRITY
REQUIREMENTS
Figure 31 is a simplified ADC sample clock input circuit.
The simplification omits many of the circuit details and
also omits parasitic elements in the circuit. These parasitic
elements play an important role in the ADC’s sample clock
input signal integrity requirements.
Logic applications tolerate signal overshoot and ringing
to a very high level. For a logic system to work properly,
the only requirement is that logic 0 and logic 1 states
are separable. A logic 0 or logic 1 state signal with large
amounts of ringing, ripple and interference causes little
concern in a logic system.
6954f
50
For more information www.linear.com/LTC6954
LTC6954
Applications Information
The ADC sample clock input has a different signal integrity
requirement than a logic input. In fact, the ADC sample
clock should never be thought of as a logic signal. It is
more like the local oscillator (LO) input signal of a mixer
where signal noise, ringing and interferers are imprinted
onto the signal of interest. However, in a mixer application, undesired out of band signals are often easily filtered
away at the output. Due to the sampling nature of an ADC,
undesired high frequency signals can fold back into the
frequency band of interest and corrupt the desired signal.
In the case of an ADC, noise, ringing and interference can
appear in the digitized data along with the analog input
signal and are not easily removed with digital filtering.
Without considering parasitic signal paths, it appears that
once the input amplifier is limiting, any noise or ringing at
the ADC’s sample clock input has no affect. However, the
ADC’s sample clock input has several parasitic elements
that provide a signal path to the track-and-hold circuit and
ultimately to the digitized data. On-chip layout and device
parasitic capacitance present one path for undesired high
frequency signals to couple into the track-and-hold. Another
path is the ADC’s substrate resistance. As this resistance
is finite, coupling through this path is also possible. The
coupling through these paths is heavily attenuated, but with
SFDR in excess of 100dB in modern ADCs, it does not take
very much coupled signal to appear in the digitized data.
USING THE LTC6954 TO DRIVE ADC SAMPLE CLOCK
INPUTS
As noted earlier, the LTC6954’s LVPECL outputs are recommended for the best phase noise performance. These
outputs are designed to interface with standard LVPECL
devices while driving transmission lines with far-end termination only. Configured this way, the signal conforms
to the LVPECL standard and the swing is very large, at
1.6VP-PDIFF. The use of far-end termination only in LVPECL
systems presents trade-offs of power consumption, signal
swing and signal integrity (overshoot and ringing).
As the LTC6954’s LVPECL output signal’s rise and fall times
are very fast (typically less than 135ps), there is typically
no need for a signal as large as the full LVPECL level at
the ADC sample clock input. An approach to consider is
to use the LVPECL outputs and provide both near-end and
far-end termination of the transmission line. The signal is
attenuated at the far end and does not meet the LVPECL
signal level specifications, but most ADC sample clock
inputs do not require a proper LVPECL level signal.
Figure 33 shows three LVPECL output configurations
that satisfy this requirement. One configuration has the
standard LVPECL common mode voltage and the other
is level-shifted down to a 1.2V common mode voltage.
Being 50% duty cycle signals, AC-coupling the outputs is
also a viable solution, as shown in the last configuration.
LVPECL+
27.4Ω
ZO
LTC6954
100Ω
LVPECL–
27.4Ω
ADC
ADCs THAT
CAN ACCEPT
A 1.8V COMMON
MODE SIGNAL
ADC
ADCs
WITH 1.2V
COMMON
MODE VOLTAGE
ADC
AC-COUPLED
INTO ADCs
WITH A SELFBIASED INPUT
ZO
LVPECL OUTPUT IBIAS ENABLED
LVPECL+
54.9Ω
ZO
49.9Ω
LTC6954
LVPECL–
49.9Ω
54.9Ω
ZO
95.3Ω
95.3Ω
LVPECL OUTPUT IBIAS DISABLED
LVPECL+
LTC6954
LVPECL–
27.4Ω
27.4Ω
ZO
100Ω
ZO
LVPECL OUTPUT IBIAS ENABLED
6954 F33
Figure 33. LVPECL Output Connections to ADC
Sample Clock Inputs (ZO = 50Ω)
6954f
For more information www.linear.com/LTC6954
51
LTC6954
Applications Information
Note that the series, near-end termination is 27.4Ω, not
50Ω. The LTC6954’s LVPECL output impedance is about
5Ω and must also be accounted for, but the biggest reason
the near-term resistor is less than 50Ω is because it adds
noise to the signal. So, the near-end termination shown
here presents a trade-off of transmission line impedance
matching over production variations (signal integrity)
against the added noise. If the far-end termination is
perfectly matched to the transmission line’s characteristic
impedance, then the near-end termination is not needed
at all. However, perfect matching is elusive, and making
provisions in the PCB layout for near-end series termination, even if initially populated with 0Ω resistors, is highly
recommended.
While the LVPECL outputs provide the best ADC sample
clock driver performance, the LVDS output can still provide
very good performance. Compared to the LVPECL output,
the LVDS output has slightly higher 1/f phase noise and
LVDS+
phase noise floor. This slightly higher phase noise, and
jitter, are still suitable for many ADC applications.
When driving the sample clock input of an ADC with the
LVDS output driver, it is best to use the highest current setting (LVCSx = 1 for ILVDS = 7mA), and a doubly-terminated
transmission line, as shown in Figure 34. This configuration is properly terminated at both ends, and is therefore
more forgiving of the transmission line design and PCB
production variations.
Using the CMOS output to drive the sample clock input
of high performance, high frequency ADCs is not recommended. Using the same output pins in LVDS output
mode is a better performing choice and certainly better for
routing the signal any significant length. However, some
ADCs require a CMOS level sample clock signal.
In these cases, the connection between the LTC6954 and
the ADC should be as short as possible with partial source
termination, as shown in Figure 35.
ZO
LTC6954
100Ω
LVDS–
ADC
100Ω
ZO
ADCs
WITH 1.2V
COMMON
MODE VOLTAGE
LVDS OUTPUT MODE, DC-COUPLED AND
DOUBLY TERMINATED INTO THE ADC SAMPLE CLOCK INPUT
(LV/CM OUTPUT IN LVDS MODE, ILVDS = 7mA)
6954 F34
Figure 34. LVDS Output Connections to ADC Sample
Clock Inputs (ZO = 50Ω)
CMOS+
LTC6954
10Ω
ZO
ADC
ADC REQUIRING
A CMOS LEVEL
SAMPLE CLOCK
CMOS–
CMOS OUTPUT MODE, DC-COUPLED INTO AN ADC
REQUIRING A CMOS LEVEL SAMPLE CLOCK
(TRANSMISSION LINE SHOULD BE NO LONGER THAN 10cm)
6954 F35
Figure 35. CMOS Output Connections to ADC Sample
Clock Inputs (ZO = 50Ω)
6954f
52
For more information www.linear.com/LTC6954
LTC6954
Typical Applications
SDO
50Ω
0.1µF
SENSE
1.8V
C19
0.1µF
C23
2.2µF
48
47
46
45
44
43
42
41
40
39
VDD VDD SENSE VREF SDO GND OF DNC D15 D14
ANALOG
0.1µF 1 V
CM
INPUT
0.1µF
T1
2
25Ω
315.5MHz
AIN+
–1dBFS
3
AIN–
25Ω
4
GND
5
REFH
0.1µF
–
+
0.1µF
6
REFL
+ CN1 –
LTC2165
7
REFH
–
+
8
REFL
C21
+
–
0.1µF
9
PAR/SER
PAR/SER
10
T1: MACOM ETC1-1-13
GND
RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE
11
CN1: 2.2µF LOW INDUCTANCE
GND
INTERDIGITATED CAPACITOR
12
VDD
TDK CLLE1AX780G225M
1.8V
MURATA LLA219C70G225M
VDD GND ENC+ ENC– CS SCK SDI GND D0 D1
C18
AVX W2L14Z225M
13 14 15
16
17 18
19 20 21
22
0.1µF
OR EQUIVALENT
100pF
0.1µF
49.9Ω
100pF
49.9Ω
OUT0+
SYNC
SYNC
CONTROL
OUT0SEL
OUT1SEL
OUT2SEL
3.3V
SDO
SPI
SERIAL
PORT
D3
24
LTC6954-3
IN–
49.9Ω
C37
0.1µF
3.3V
V+
IN+
D2
23
DIGITAL
OUTPUTS
1.8V
C32
0.1µF
C28
0.1µF
100pF
37
D13 D12
36
D11
35
D10
34
D9
33
D8
32
OVDD
31
OGND
30
CLKOUT+
29
CLKOUT–
28
D7
27
D6
26
D5
25
D4
SPI
PORT
R51
100Ω
1GHz
38
SERIAL
PORT
AND
DIGITAL
DEL = 0
DIV = 10
DELAY
0 TO 63
DIVIDE
1 TO 63
DELAY
0 TO 63
DIVIDE
1 TO 63
100MHz
OUT0–
OUT1+
OUT1–
OUT2+
OUT2–
SDI
SCLK
CS
GND
6954 F36
Figure 36. LTC6954 Driving the Encode Sample Clock Input of an LTC2165, 125Msps, 16-Bit ADC
6954f
For more information www.linear.com/LTC6954
53
LTC6954
Typical Applications
0
TOTAL SYSTEM SNR = 68.8dB
LTC6954 JITTER = 113fsRMS
–10
–20
AMPLITUDE (dBFS)
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
0
10
20
30
FREQUENCY (MHz)
40
50
6954 F37
Figure 37. LTC2165 64k Point FFT, fIN = 315MHz, –1dBFS, 100Msps.
Sample Clock Provided by the LTC6954 at 100MHz
6954f
54
For more information www.linear.com/LTC6954
LTC6954
Package Description
Please refer to http://www.linear.com/product/LTC6954#packaging for the most recent package drawings.
UFF Package
36-Lead Plastic QFN (4mm × 7mm)
(Reference LTC DWG # 05-08-1863 Rev Ø)
0.70 ±0.05
4.50 ±0.05
3.10 ±0.05
5.61 ±0.05
2.50 REF
2.64 ±0.05
PACKAGE OUTLINE
0.25 ±0.05
0.50 BSC
5.50 REF
6.10 ±0.05
7.50 ±0.05
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
4.00 ±0.10
PIN 1 NOTCH
R = 0.30 OR
0.25 × 45°
CHAMFER
R = 0.10
TYP
0.75 ±0.05
2.50 REF
35
36
0.40 ±0.10
PIN 1
TOP MARK
(NOTE 6)
7.00 ±0.10
1
2
5.50 REF
5.61 ±0.10
2.64 ±0.10
(UFF36) QFN 0810 REV Ø
0.200 REF
0.00 – 0.05
R = 0.125
TYP
0.25 ±0.05
0.50 BSC
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LTC6954
6954f
55
LTC6954
Typical Application
UP TO 1.4GHz
Additive Phase Noise vs Offset
Frequency, fIN = 622.08MHz,
Mx[5:0] = 4, fOUTx = 155.52MHz
3.3V
V+
IN+
IN
50Ω
SYNC
50Ω
DELAY
0 TO 63
SYNC
CONTROL
OUT0SEL
DELAY
0 TO 63
OUT1SEL
3.3V
OUT2SEL
SDO
SPI
SERIAL
PORT
SDI
SERIAL
PORT
AND
DIGITAL
DELAY
0 TO 63
–120
LTC6954-3
–
DIVIDE
1 TO 63
DIVIDE
1 TO 63
DIVIDE
1 TO 63
OUT0+
OUT0–
OUT1+
OUT1–
OUT2+
OUT2–
LVPECL OUTPUT
FREQUENCY
UP TO 1.4GHz
LVDS OUTPUT
FREQUENCY
UP TO 1.4GHz
CMOS OUTPUT
FREQUENCY
UP TO 250MHz
SCLK
ADDITIVE PHASE NOISE (dBc/Hz)
0.1µF
–130
–140
–150
–160
–170
–180
CS
GND
6954 TA02a
10
100
1k
10k 100k
1M
OFFSET FREQUENCY (Hz)
10M
6954 TA02b
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LTC6945
Ultralow Noise and Spurious Integer-N Synthesizer
350MHz to 6GHz, –226dBc/Hz Normalized In-Band Phase Noise Floor,
–157dBc/Hz Wideband Output Phase Noise Floor
LTC6946
Ultralow Noise and Spurious Integer-N Synthesizer
with Integrated VCO
370MHz to 6.4GHz, –226dBc/Hz Normalized In-Band Phase Noise Floor,
–157dBc/Hz Wideband Output Phase Noise Floor
LTC6947
Ultralow Noise and Spurious Fractional-N Synthesizer
350MHz to 6GHz, –226dBc/Hz Normalized In-Band Phase Noise Floor,
–157dBc/Hz Wideband Output Phase Noise Floor, Integer-N Spurious
Performance
LTC6948
Ultralow Noise and Spurious Fractional-N Synthesizer
with Integrated VCO
370MHz to 6.4GHz, –226dBc/Hz Normalized In-Band Phase Noise Floor,
–157dBc/Hz Wideband Output Phase Noise Floor, Integer-N Spurious
Performance
LTC6950
Low Phase Noise and Spurious Integer-N PLL Core with
Five Output Clock Distribution and EZSync Clock Edge
Synchronization
1.4GHz Max VCO Frequency, Additive Jitter <20fsRMS, –226dBc/Hz
Normalized In-Band Phase Noise Floor, –274dBc/Hz Normalized 1/f Phase
Noise Floor
LTC6957
Low Phase Noise, Dual Output Buffer/Driver/Logic
Converter
Optimized Conversion of Sine Waves to Logic Levels, LVPECL/LVDS/CMOS
Outputs, DC-300MHz, 45fsRMS additive jitter (LVPECL)
6954f
56 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC6954
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTC6954
LT 1115 • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2015