SY89537L 3.3V Precision LVPECL and LVDS Programmable Multiple Output Bank Clock Synthesizer and Fanout Buffer General Description The SY89537L integrated programmable clock synthesizer and fanout is part of a precision PLLbased clock generation family optimized for enterprise switch, router, and multiprocessor server applications. This family is ideal for generating internal system timing requirements up to 700MHz for multiple ASICs, FPGAs, and NPUs. These devices integrate the following blocks into a single monolithic IC: • PLL (Phase-Lock-Loop) based synthesizer • Fanout buffers • Clock generator (dividers) • Logic translation (LVPECL, LVDS) • Five independently programmable output banks This level of integration minimizes additive jitter and part-to-part skew associated with discrete alternatives, resulting in superior system-level timing with reduced board space and power. For applications that require a zero-delay function, see the SY89538L. All support documentation can be found on Micrel’s web site at: www.micrel.com. Applications • Enterprise routers, switches, servers and workstations • Parallel processor-based systems • Internal system clock generation for ASICs, NPUs, FPGAs Markets • LAN/WAN • Enterprise servers • Test and measurement Precision Edge® Features • Integrated programmable synthesizer with multiple output dividers, fanout buffers, and clock drivers • Direct interface to crystal: 14MHz to 18MHz • Input MUX accepts a reference and a crystal (XTAL) source – Ideal for reference backup clock source or system test frequency source – Patent-pending unique input MUX isolates XTAL and reference inputs minimizes crosstalk • Guaranteed AC performance: – 87.15MHz to 700MHz output frequency range (with RFCK at 16.6MHz) – <100psPP total jitter – <7psRMS cycle-to-cycle jitter – <8psPP deterministic jitter – <0.7psRMS crosstalk induced jitter – <50ps bank-to-bank skew • Output bank synchronization control pin • LVPECL and LVDS outputs • TTL/CMOS compatible control logic • Five independently programmable output frequency banks: – Four differential LVPECL output banks – One differential LVDS output bank with 3 output pairs • Separate output enable for each bank • 3.3V ±10% power supply (2.5V output capable) • Guaranteed over the commercial and industrial temperature range (-40C to +85C) • Available in 44-pin (7mm x 7mm) MLF™ package Precision Edge is a registered trademark of Micrel, Inc. MLF and MicroLeadFrame are trademarks of Amkor Technology, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com August 2005 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Functional Block Diagram August 2005 2 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Ordering Information(1) Package Marking Lead Finish Industrial SY89537LMG with Pb-Free bar-line indicator NiPdAu Pb-Free Industrial SY89537LMG with Pb-Free bar-line indicator NiPdAu Pb-Free Part Number Package Type Operating Range SY89537LMG MLF-44 SY89537LMGTR(2) MLF-44 Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. Pin Configuration 44-Pin MLFTM (MLF-44) August 2005 3 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Pin Description Power Pin Number 1 3 Pin Name VCCA VCCD Pin Function Analog PLL Power Pin: Connects to “quiet” 3.3V supply. 3.3V power pins are not internally connected on the die, and must be connected together on the PCB. Bypass with 0.1µF//0.01µF low ESR capacitors and place as close to the VCCA pin as possible. Digital Logic Core Power Pin: VCCD connects to a 3.3V supply. Power pins are not internally connected on the die, and must be connected together on the PCB. Bypass with 0.1µF//0.01µF low ESR capacitors and place bypass capacitors as close to the VCCD pin as possible. 14, 27, 30, 36 VCCO LVDS and LVPECL Output Driver Power Pins: The outputs can be powered from a 2.5V supply or 3.3V supply. Connect all VCCO pins to the same power supply: 3.3V ±10% or 2.5V ±5%. Power pins are not internally connected on the die, and must be connected together on the PCB. Bypass with 0.1µF//0.01µF low ESR capacitor and place as close to the VCCO pin as possible. 10 GNDA PLL Ground: Connect to “quiet” ground. GNDA and GND are not internally connected on the die, and must be connected on the PCB. 11, 21, 22 GND, Exposed Pad Ground: GND pins and exposed pad must both be connected to the most negative potential of the chip ground. Control and Configuration Pin Number Pin Name 43 LR Analog Input/Output: Provides the reference voltage for the PLL loop filter and is used with the LF pin. See "External Loop Filter Considerations" for recommended loop filter values. 44 LF Analog Input/Output: Provides the loop filter node for the PLL. See “External Loop Filter Considerations” for loop filter values. 2, 4 RSEL1, RSEL0 7 INSEL TTL/CMOS Input Select Control. Selects either XTAL or Reference (RFCK) input. Internal 25kΩ pull-up. The default is logic HIGH, and selects the XTAL input. The threshold voltage VTH = VCC/2. Logic HIGH: XTAL Select Logic LOW: Reference Input Select 23 LSEL TTL/CMOS input select control signal for the LVDS LOUT0-LOUT2 outputs. LSEL and LEN are used to decode the selection and the post divider of the LVDS output bank. LSEL includes an internal 25kΩ pull-up. See “LVDS Output and Frequency Select Table” for proper decoding. The threshold voltage VTH = VCC/2. 24 LEN TTL/CMOS Input Enable Pin. Used to control the LOUT0-LOUT2 outputs and acts as a frequency select pin. LEN and LSEL are used to decode the selection and the post divider of the LVDS output bank. See the “LVDS Output and Frequency Select Table” for proper decoding. LEN includes an internal 25kΩ pull-up. When disabled, LOUT0-LOUT2 outputs are LOW, and the complimentary outputs are HIGH. The threshold voltage VTH = VCC/2. 17 19 39 41 PSEL0 PSEL1 PSEL2 PSEL3 TTL/CMOS input select control signals for the PECL POUT0-POUT3 outputs. PSELx and PENx are used together to decode the selection and post divider of the PECL outputs. PSELx pins include an internal 25kΩ pull-up. The threshold voltage VTH = VCC/2. See "PECL Output Frequency and Select Table" for proper decoding. 18 20 40 42 PEN0 PEN1 PEN2 PEN3 TTL/CMOS input enable pin. Used to control the POUT0-PECL2 outputs and acts as a frequency select pins. PENx and PSELx are used together; see the “PECL Output and Frequency Select Table” for proper decoding. PENx includes an internal 25kΩ pull-up. When disabled, PECL0-PECL2 outputs are LOW. The threshold voltage VTH = VCC/2. 33 SYNC TTL/CMOS output bank synchronization control. Internal 25kΩ pull-up. The default state is HIGH. After any bank has been programmed, all PECL and LVDS outputs are synchronized when the SYNC control pin is toggled with a HIGH-LOW-HIGH transition. See “Synchronization” section for details. The threshold voltage VTH = VCC/2. August 2005 Pin Function TTL/CMOS Reference Input Pre-scaler. The two-bit input pre-scaler divides the input reference frequency by /1, /2, /4, or /8. RSEL0 is the LSB bit. See "Reference Input Divider Select Table," for proper decoding. The threshold voltage VTH = VCC/2. Internal 25kΩ pull-up. 4 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Pin Description (continued) Input/Output Pin Number Pin Name 5, 6 RFCK, /RFCK Pin Function Reference Clock Differential Input. Input accepts any input, single-ended or differential: TTL/CMOS, LVPECL, LVDS, HSTL, and SSTL. RFCK requires external termination. See "Input Interface" section for details. XTAL2, XTAL1 Crystal Input. Directly connect a series resonant crystal across inputs. See “Quartz Crystal Oscillator Specification” table. Place crystal as close to the input as possible, keep XTAL and traces away from adjacent noisy traces to minimize noise coupling, and place the XTAL on the same side as the SY89537L (component side). 12, 13 15, 16 34, 35 37, 38 POUT0, /POUT0 POUT1, /POUT1 POUT2, /POUT2 POUT3, /POUT3 100K LVPECL Output Drivers. Terminate all PECL outputs with 50Ω to VCCO-2V. Each output pair has respective output frequency control (PSELx, PENx) pins. See "PECL Output and Frequency Select Table" for proper coding. For low jitter applications, unused PECL output pairs should be terminated with pull-down resistors. See "Output Termination Recommendations" section for termination detail. 25, 26 28, 29 31, 32 LOUT0, /LOUT0 LOUT1, /LOUT1 LOUT2, /LOUT2 Differential LVDS Compatible Output Drivers. Output termination is 100Ω across the pair. For low-jitter applications, unused LVDS output pairs should be terminated with 100Ω across the pair. See “Output Termination Recommendations” section for details. 8, 9 Reference Input Driver Select Table RSEL1 RSEL0 Internal Reference Clock 0 0 RFCK / 8 0 1 RFCK / 4 1 0 RFCK / 2 1 1 RFCK / 1 Table 1. Reference Input Divider Select Table Output and Frequency Select Tables PSELx PENx POUTx 0 0 Disable Output 0 1 (VCO/4) / 2 1 0 (VCO/4) / 8 1 1 (VCO/4) / 1 Table 2. PECL Output and Frequency Select Table LSEL LEN LOUTx 0 0 Disable Output 0 1 (VCO/4) / 2 1 0 (VCO/4) / 8 1 1 (VCO/4) / 1 Table 3. LVDS Output and Frequency Select Table August 2005 5 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VCC) .......................... –0.5V to +4.0V Input Voltage (VIN) .................................. –0.5V to VCC XTAL Input Voltage (VXTAL1, 2) ......... VCC –1.9V to VCC Output Current (IOUT) LVPECL Outputs ......................................±50mA LVDS Outputs...........................................±10mA Lead Temperature (soldering, 20 sec.) .......... +260°C Storage Temperature (Ts) ................. –65°C to 150°C Supply Voltage (VCCD, VCCA) ...................... +3.0V to +3.6V Supply Voltage (VCCO)........................... +2.375V to +3.6V Ambient Temperature (TA)....................... –40°C to +85°C Package Thermal Resistance(3) MLF™ (θJA) Still-Air.........................................................24°C/W MLF™ (ψJB) Junction-to-Board..........................................8°C/W DC Electrical Characteristics(4) Power Supply TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter Condition Min Typ Max Units VCCA PLL Power Supply Note 5 3.0 3.3 3.6 V VCCD Control Logic Supply Voltage Note 5 3.0 3.3 3.6 V VCCO Output Supply Voltage 2.375 2.5 2.625 V 3.3 3.6 V ICC Total Power Supply Current No load, max. VCC, Note 6 240 300 mA ICCA Analog Supply Current Max. VCC 10 mA ICCO Output Supply Current No load, max. VCC 55 mA ICCD Digital Supply Current Max. VCC 175 mA 3.0 LVCMOS/LVTTL Input Control Logic VCCA = VCCD +3.3V ±10%, VCCO = +2.5V ±5% or +3.3V ±10%; TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter Condition Min VIH Input High Voltage VIL Input Low Voltage IIH Input High Current VIN = VCC –125 IIL Input Low Current VIN = 0.5V –300 Typ Max 2.0 Units V 0.8 V 150 µA µA Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the devices most negative potential on the PCB. θJA and ΨJB values are determined for a 4-layer board in still-air, unless otherwise stated. 4. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. 5. VCCA and VCCD are not internally connected. They must be connected together on the PCB. 6. ICC = ICCA + ICCO + ICCD. August 2005 6 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Reference Clock Input VCCA = VCCD +3.3V ±10%, VCCO = +2.5V ±5% or +3.3V ±10%; TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter Condition Min Typ Max Units VIH Input HIGH Voltage RFCK, /RFCK VCCD + 0.3 V VIL Input LOW Voltage RFCK, /RFCK –0.3 V VIN Input Voltage Swing RFCK, /RFCK, See Figure 1a. 100 mV VDIFF-IN Differential Input Voltage Swing RFCK, /RFCK, See Figure 1b. 200 mV LVPECL Output DC Electrical Characteristics VCCA = VCCD +3.3V ±10%, VCCO = +2.5V ±5% or +3.3V ±10%, RL = 50Ω into VCCO–2V; TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter Max Units VOH Output HIGH Voltage Condition VCCO –1.075 Min Typ VCCO –0.830 V VOL Output LOW Voltage VCCO –1.860 VCCO –1.570 V VOUT Output Voltage Swing See Figure 1a. 550 800 mV VDIFF-OUT Differential Output Voltage Swing See Figure 1b. 1100 1600 mV LVDS Output DC Electrical Characteristics VCCA = VCCD +3.3V ±10%, VCCO = +2.5V ±5% or +3.3V ±10%, RL = 100Ω across the pair; TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter Condition Min Typ Max Units VOUT Output Voltage Swing See Figure 1a. 250 325 mV VDIFF-OUT Differential Output Voltage Swing See Figure 1b. 500 650 mV VOCM Output Common Mode Voltage ∆VOCM Change in Common Mode Voltage August 2005 1.125 7 1.275 V 25 mV M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L AC Electrical Characteristics VCCA = VCCD = +3.3V ±10%; VCCO = +2.5V ±5% or +3.3V ±10%, RL (LVDS) = 100Ω across the output, RL (LVPECL) = 50Ω into VCCO–2V; TA = –40°C to +85°C, unless otherwise stated. Symbol fIN fPHASE fOUT fVCO tSKEW tLOCK tJITTER BW tDC tr, tf Parameter XTAL Input Frequency Range Reference Input Frequency Range Phase Detector Operating Frequency Range Output Frequency Range Internal VCO Frequency Range LVPECL Output Banks (0–3), Bank-to-Bank LVDS Output Banks (0–2), Bank-to-Bank Part-to-Part Skew Condition Note 7 Min 14 14 14 73.5 2352 Note 8 Typ 15 15 Note 9 PLL Lock Time Loop Filter Optimized for Cycle-to-Cycle Jitter • R = 130Ω • C1 = 0.47µF • C2 = 100pF 1-Sigma Cycle-to-Cycle Jitter (XTAL Reference) 1-Sigma Cycle-to-Cycle Jitter (RFCK Reference) Deterministic Jitter Total Jitter Spur Note 10 Note 10 Note 11 Note 12 XTAL/RFCK Crosstalk-Induced Jitter PLL Bandwidth FOUT Duty Cycle Output Rise/Fall Time (20% to 80%) LVPECL Output Rise/Fall Time (20% to 80%) LVDS Note 13 See “PLL Stability” Table See “Synchronization” 4 5 5.5 80 -35 28.8 43 100 80 8 50 250 150 tPW_SYNC_MIN See “Synchronization” 8 tPD_SYNC Max 18 144 18 756 3024 50 50 200 10 Units MHz MHz MHz MHz MHz ps ps ps ms 6 7 8 100 psRMS psRMS psPP psPP dBc@ fphase 0.7 99.8 57 400 300 psRMS kHz % ps ps Internal clock cycle Internal clock cycle Notes: 7. Fundamental mode, series resonant crystal. 8. The bank-to-bank skew is defined as the worst-case difference between any two similar delay paths within a single device operating at the same voltage and temperature. 9. Part-to-part skew is defined for two parts with identical power supply voltages at the same temperature and with no skew of the edges at the respective inputs. 10. Cycle-to-cycle jitter definition: the variation of periods between adjacent cycles, Tn – Tn-1 where T is the time between rising edges of the output signal. 23 11. Deterministic jitter is measured at 2.5Gbps with both K28.5 and 2 -1 PRBS pattern. 12 12. Total jitter definition: with an ideal clock input of frequency <fMAX, no more than one output edge in 10 output edges will deviate by more than the specified peak-to-peak jitter value. 13. Crosstalk is measured at the output while applying two similar differential clock frequencies that are asynchronous with respect to each other at the inputs. August 2005 8 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Single-Ended and Differential Swings Figure 1b. Differential Voltage Swing Figure 1a. Single-Ended Voltage Swing August 2005 9 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Oscillator Tips 1. Mount the crystal as close to the SY89537L as possible to minimize parasitic effects. 2. Mount on the same plane as the SY89537 to minimize on via hole inductance. 3. To minimize noise pick up on the loop filter pins, cut the ground plane directly underneath the loop filter component pads and traces. 4. Keep the crystal and its traces away from adjacent noisy traces to minimize on noise coupling. Functional Description Overall Function The SY89537L integrated programmable clock synthesizer and fanout buffer is part of a precision PLL-based clock generation family optimized for internal system clock generation for (FPGAs, ASICs, NPU) applications. Input MUX The device’s input patent-pending MUX accepts both a single-ended or differential reference clock; and a 14MHz to 18MHz series resonant crystal (XTAL). The input MUX has built-in isolation, which minimizes crosstalk between the two inputs. The input MUX drives the PLLs phase detector, which expects a frequency between 14MHz and 18MHz, therefore, the reference clock can be a maximum frequency of 144MHz when the reference divider is set to: divideby-8. The minimum frequency that the reference accepts is 14MHz when the reference divider is set at: divide-by-1. Table 4 illustrates the crystal specifications. Figure 2 below illustrates how to interface the crystal with the SY89537L. Figure 2. Crystal Interface PLL VCO The VCOs range of operation is from 2.352GHz to 3.024GHz, and the output frequency range is from 73.5MHz to 756MHz. The minimum output frequency is calculated according to the following equation: fOUT = Quartz Crystal Selection: Note: Raltron Series Resonant: AS-16.666-S-SMD-T-MI (2) Raltron External Loop Filter Considerations The SY89537L features an external PLL loop filter that allows the users to tailor the PLLs behavior. It is recommended that ceramic capacitors with NPO or X7R dielectric be used, since they have very low effective series resistance. For applications that require ultra-low, cycle-to-cycle jitter, use the components shown in Figure 3a. For best total jitter and best spur reduction, use the components shown in Figure 3b. Larger values of the pole capacitor (C2) results in less total jitter; however, the loop stability decreases. Loop stability decreases since the pole capacitor begins to dominate over the zero capacitor (C1). The external loop filter allows the user to change the loop filter values for specific jitter requirements. Using a smaller resistor in the loop filter decreases the PLLs loop bandwidth. This results in less noise from the PLL input, but potentially more noise from the VCO. fphase × Pre Divider × FeedbackDi vider PreDivider × OutoutDivi der × PostDivide r fOUT (min) = 14MHz × 2 × 84 2×2×8 fOUT (min) = 73.5MHz The maximum output frequency according to the following equation: fOUT (max) = is calculated 18MHz × 2 × 84 2 × 2 ×1 fOUT (max) = 756MHz Crystal Input and Oscillator Interface The SY89537L features a fully integrated on-board oscillator, which minimizes system implementation cost. The oscillator is a series resonant, multi-vibrator type crystal driver. August 2005 Figure 3a. Loop Filter for Lowest Cycle-to-Cycle Jitter 10 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Figure 3b. Loop Filter for Lowest Total Jitter and Best Reference Spur Reduction The reference spur is located at the phase detector frequency away from the carrier frequency. The attenuation of the reference spur is a function of the loop filter. Figure 4a shows the attenuation of the reference spur with the loop filter shown in Figure 3a. Figure 4b shows the attenuation of the reference spur with the loop filter shown in Figure 3b. Figure 4b. Reference Spur at -52dB at 16MHz (R = 130Ω, C1 = 0.47µF, C2 = 1000pF) Crystal Frequency: 14MHz to 18MHz Power Supply Filtering Techniques Mode of Oscillation: Fundamental Min. Typ. Max. Unit Frequency Tolerance @25°C ±30 ±50 ppm Frequency Stability over 0*C to 70°C ±50 ±100 ppm Operating Temperature Range –20 +70 °C Storage Temperature Range –55 +125 °C Aging (per yr/1 3yrs) ±5 ppm Equivalent Series Resistance (ESR) 50 Ω st Drive Level 100 As with any high-speed integrated circuit, power supply filtering is very important. At a minimum, VCCA, VCCD, and all VCCO pins should be individually connected using a via to the power supply plane, and separate bypass capacitors should be used for each pin. To achieve optimal jitter performance, each power supply pin should use separate instances of the circuit shown in Figure 5. µW Table 4. Quartz Crystal Oscillator Specifications Figure 5. SY89537L Recommended Power Supply De-Coupling Note: For VCCA and VCCD use ferrite bead, Murata P/N BLM21A1025. For VCCO use ferrite bead, Murata, P/N BLM31P005. Figure 4a. Reference Spur at -39dB at 16MHz (R = 130Ω, C1 = 0.47µF, C2 = 100pF) August 2005 11 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Synchronization Output Synchronization Controlled by SYNC Timing Diagram asserted with a rising edge, the outputs are enabled when all internal divider stages are reaching their LOW state. This ensures a simultaneous switching of all outputs with the next LOW-HIGH transition of the pre-divider clock. The SYNC control input is used to synchronize all divider outputs of the post divider. When a HIGH-LOW transition is applied to the SYNC control input the outputs are disabled when all post-divider outputs are LOW, see “Output Synchronization Controlled by SYNC Timing Diagram” for details. Once SYNC is August 2005 12 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L loop stability in terms of damping factor, natural frequency, and bandwidth, and illustrates the pole and zero cutoff frequencies determined by the loop filter PLL Stability For the loop filter configurations shown in Figure 3a and 3b, Table 5a and 5b below summarizes the PLLs Parameter VCC Temperature VCO Frequency Charge Pump Current Loop Filter Resistor Units 3 3 3 3.3 3.3 3.3 3.6 3.6 3.6 V –40 -40 -40 25 25 25 85 85 85 C 2352 2800 3024 2352 2800 3024 2352 2800 3024 MHz 1.80E-04 1.80E-04 1.80E-04 1.80E-04 1.80E-04 1.80E-04 1.80E-04 1.80E-04 1.80E-04 A 130 130 130 130 130 130 130 130 130 Ω F Zero Capacitor 4.70E-07 4.70E-07 4.70E-07 4.70E-07 4.70E-07 4.70E-07 4.70E-07 4.70E-07 4.70E-07 Pole Capacitor 1.00E-09 1.00E-09 1.00E-09 1.00E-09 1.00E-09 1.00E-09 1.00E-09 1.00E-09 1.00E-09 F VCO Gain (KVCO) 3.20E+09 4.50E+09 4.50E+09 2.80E+09 3.30E+09 3.10E+09 2.30E+09 1.70E+09 1.30E+09 Hz/V Feedback Divider 168 168 168 168 168 168 168 168 168 Integer Phase Detector Frequency 14 16 18 14 16 18 14 16 18 MHz Damping Factor 2.6 3.1 3.1 2.4 2.6 2.6 2.2 1.7 1.9 13600.29 16127.95 16127.95 12721.90 13811.16 13386.09 11530.20 9912.83 8668.52 197 160 180 225 219 262 274 424 624 Natural Frequency Ratio=Phase Detector Freq/BW Hz Zero Frequency 2.61E+03 2.61E+03 2.61E+03 2.61E+03 2.61E+03 2.61E+03 2.61E+03 2.61E+03 2.61E+03 Hz Loop Bandwidth (BN) 7.1E+04 9.98E+04 9.98+04 6.21E+04 7.32E+04 6.88E+04 5.1E+04 3.77E+04 2.88E+04 Hz Pole Frequency 1.22E+07 1.22E+07 1.22E+07 1.22E+07 1.22E+07 1.22E+07 1.22E+07 1.22E+07 1.22E+07 Hz Table 5a. Optimized for Lowest Cycle-to-Cycle Jitter (R = 130Ω, C1 = 0.47µF, C2 = 100pF) August 2005 13 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Parameter VCC Temperature VCO Frequency Charge Pump Current Loop Filter Resistor Units 3 3 3 3.3 3.3 3.3 3.6 3.6 3.6 V –40 -40 -40 25 25 25 85 85 85 C 2352 2800 3024 2352 2800 3024 2352 2800 3024 MHz 1.80E-04 1.80E-04 1.80E-04 1.80E-04 1.80E-04 1.80E-04 1.80E-04 1.80E-04 1.80E-04 A 130 130 130 130 130 130 130 130 130 Ω F Zero Capacitor 4.70E-07 4.70E-07 4.70E-07 4.70E-07 4.70E-07 4.70E-07 4.70E-07 4.70E-07 4.70E-07 Pole Capacitor 1.00E-09 1.00E-09 1.00E-09 1.00E-09 1.00E-09 1.00E-09 1.00E-09 1.00E-09 1.00E-09 F VCO Gain (KVCO) 3.20E+09 4.50E+09 4.50E+09 2.80E+09 3.30E+09 3.10E+09 2.30E+09 1.70E+09 1.30E+09 Hz/V Feedback Divider 168 168 168 168 168 168 168 168 168 Integer Phase Detector Frequency 14 16 18 14 16 18 14 16 18 MHz Damping Factor Natural Frequency Ratio=Phase Detector Freq/BW 2.6 3.1 3.1 2.4 2.6 2.6 2.2 1.7 1.9 13600.29 16127.95 16127.95 12721.90 13811.16 13386.09 11530.20 9912.83 8668.52 197 160 180 225 219 262 274 424 624 Hz Zero Frequency 2.61E+03 2.61E+03 2.61E+03 2.61E+03 2.61E+03 2.61E+03 2.61E+03 2.61E+03 2.61E+03 Hz Loop Bandwidth (BN) 7.1E+04 9.98E+04 9.98+04 6.21E+04 7.32E+04 6.88E+04 5.1E+04 3.77E+04 2.88E+04 Hz Pole Frequency 1.22E+06 1.22E+06 1.22E+06 1.22E+06 1.22E+06 1.22E+06 1.22E+06 1.22E+06 1.22E+06 Hz Table 5b. Optimized for Total Jitter (R = 130Ω, C1 = 0.47µF, C2 = 1000pF) August 2005 14 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Figure 6 shows the open and closed loop gain of the SY89537L. The closed loop-gain plot shows that the SY89537L when configured with the recommended loop filter values has essentially no jitter peaking near the -3dB point. In addition, the open loop curve shows the frequency at which unity gain occurs for a typical case of the SY89537L with VCC = 3.3V at TA = 25°C. At unity gain, Figure 7 can be used to determine the phase margin or stability of the SY89537L. dB Figure 8. VCO Frequency vs. Loop Filter Control Voltage at 3.3V, TA = 25°C Frequency (Hz) Figure 6. Open and Closed Loop Gain at VCC = 3.3V, TA = 25°C Figure 9. VCO Gain vs. Loop Filter Control Voltage at 3.3V, TA = 25°C Phase Margin (°) Input Interface RFCK is designed to accept any differential or singleended input signal 300mV above VCC or 300mV below GND. RFCK should not be left floating. Tie either the true or complement input to GND, but not both. A logic zero is achieved by connecting the complement input to GND with the true input floating. For TTL input, tie a 2.5kΩ resistor between the complement input and GND. LVDS, CML and HSTL differential signals may be connected directly to the reference inputs. Frequency (Hz) Figure 7. Phase Margin Plot at VCC = 3.3V, TA = 25°C Figure 8 illustrates the VCO frequency versus the loop filter control voltage at 3.3V, TA = 25°C. The normal loop filter control voltage is -300mV to +300mV. Figure 9 illustrates the VCO gain curve at VCC = 3.3V, TA = 25°C. With this set of information, determining the loop stability with other sets of loop filter configurations are possible. Figure 10. Simplified Input Structure August 2005 15 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Input Termination Figure 11a. LVPECL Interface (DC-Coupled) Figure 11b. LVPECL Interface (AC-Coupled) Figure 11c. CML Interface (DC-Coupled) Figure 11d. CML Interface (AC-Coupled) Figure 11e. LVDS (DC-Coupled) Figure 11f. 2.5V LVPECL (DC-Coupled) Figure 11g. 2.5V CML (DC-Coupled) August 2005 16 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Output Bank and Frequency Control There are five independently programmable output frequency banks, four differential LVPECL output banks and one differential LVDS output bank with three output pairs. Each bank has frequency control SELx and Enx to generate different divider ratios (see “PECL and LVDS Output and Frequency Select” Tables). It can be programmed for pass-through, internal divided VCO clock divide-by- /2, /8 or disable state. When disabled, the non-inverted output goes to static LOW and the inverted output goes to static HIGH. Figure 12a. Parallel Thevenin-Equivalent Output Logic Characteristics See “Output Termination Recommendations” for proper termination. When LVPECL single-ended output is desired, the unused complimentary output should be terminated. Unused LVPECL output pairs can be left floating. LVDS output pairs should be terminated with 100Ω across the pair. In order to minimize jitter and skew, unused LVDS output banks and unused LVDS output pairs should be terminated with 100Ω across each pair. LVPECL Outputs: • Typical voltage swing is 800mV into 50Ω. • Common mode voltage is VCCO–1.3V. Figure 12b. Parallel Termination LVDS LVDS specifies a small swing of 325mV typical, on a nominal 1.2V common mode above ground. The common mode voltage has tight limits to permit large variations in ground between an LVDS driver and receiver. Also, change in common mode voltage, as a function of data input, is kept to a minimum, to keep EMI low. LVDS Outputs: • Typical voltage swing is 325mV into 100Ω. • Common mode voltage is 1.2V. Output Termination Recommendations LVPECL LVPECL has high input impedance, very low output (open emitter) impedance, and small signal swing which results in low EMI. LVPECL is ideal for driving 50Ω-and-100Ω-controlled impedance transmission lines. There are several techniques for terminating the LVPECL output: Parallel Termination TheveninEquivalent, Parallel Termination (3-resistor), and ACcoupled termination. Unused output pairs may be left floating. However, single-ended outputs must be terminated, or balanced. Figure 13a. LVDS Differential Measurement Figure 13b. LVDS Common Mode Measurement August 2005 17 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Related Product and Support Documentation Part Number Function Data Sheet Link SY89538L 3.3V, Precision LVPECL and LVDS Programmable, Multiple Output Bank Clock Synthesizer and Fanout Buffer with Zero Delay http://www.micrel.com/product-info/products/sy89538l.shtml HBW Solutions New Products and Applications www.micrel.com/product-info/products/solutions.shtml MLF August 2005 TM Application Note www.amkor.com/products/notes_papers/MLFAppNote.pdf 18 M9999-080305 [email protected] or (408) 955-1690 Micrel, Inc. SY89537L Package Information 44-Pin MLF™ (MLF-44) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2005 Micrel, Incorporated. August 2005 19 M9999-080305 [email protected] or (408) 955-1690