AXLE7050B

 Rev.: 1 Date: 2016‐01‐20 Specification AXLE7050B Oscillator type: High Stability SMD (VC)TCXO in 7x5 mm package Parameter Frequency range Nominal frequencies min. Load Amplitude (peak‐peak)
VOL VOH Duty cycle Rise/fall time Phase noise @ 25°C Supply voltage VS ±0.5
± 0.05 to ± 2.0
See tables 1 ~ 3 ±0.1
±0.2
±1
±5
0.5
1.5
Positive
±12
2.5
100
Clipped Sine Wave
HCMOS 10 kΩ || 10 pF
15 pF 0.8
0.4
2.4
45
55
6
3.15
4.75 3.3
5.0 Enclosure (see drawing) (LxWxH) Weight Packing 3.45
5.25 6.0
7.0x5.0x1.9
Other frequencies on request @ VCnom Note 2
Option 4 & 5 ppm
ppm
ppm
VS ±5 % Load ±5 % @+40°C Note 3
ppm
V
Option 1 = “V” V
V
V
%
ns
dBc/Hz
V
V mA
mm
g
3
Condition ppm
ppm
kΩ
Current consumption Notes: 1.
2.
3.
4.
max. Unit 10
52
MHz
10, 12.8, 16.384, 19.2, 19.44, MHz
20, 24.576, 25, 26, 30.72., 38.4, 38.88, 40 Frequency stability Initial tolerance @ 25°C at delivery vs. operating temperature range vs. supply voltage variation vs. load change Long term (aging) 1st year Frequency adjustment range Electronic Frequency Control (EFC) EFC voltage VC EFC slope (f / VC) EFC input impedance RF output Signal waveform typ. Tape & Reel
Option 3 = “C” Option 3 = “H” Option 3 = “C” Option 3 = “H” Option 3 = “C” Option 3 = “H” See table 4 Option 2 = “33” Option 2 = “50” IEC 61837 IEC 60286‐3 Terminology and test conditions are according to IEC60679‐1 and MIL‐PRF‐55310, unless otherwise stated Tolerance will be increased after reflow soldering Lower aging on request All combinations of options might not be available. Please consult factory Absolute Maximum Ratings Parameter min.
max.
Supply Voltage VS Control Voltage VC Storage Temperature ‐0.5
‐0.5
‐55
VS + 10%
6
+125
GmbH & Co. KG
Roemerring 9 D‐74821 Mosbach Germany AXLE7050B Rev.1 Drawing D1 Page 1(4) Unit
Condition V
V
°C
VS to GND VC to GND ww.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E‐mail: [email protected] Frequency stability vs. temperature Option 4 005 01 02 05 10 15 20 Table 1 Stability* [ppm] ±0.05 ±0.1 ±0.2 ±0.5 ±1.0 ±1.5 ±2.0 Lower Temperature
Option 5
T [°C]
0 0
1 ‐10
2 ‐20
3 ‐30
4 ‐40
5 ‐50
6 ‐55
Table 2 Upper Temperature Option 5
T [°C] A
+50
B
+60
C
+70
D
+75
E
+80
F
+85
G
+90
H
+95
*stability referred to (fmax+fmin)/2 Frequency stability [Option 2]
Temperature range [°C] 005 01 02
05
10
‐20 ~ +70 O X X
X
X
‐40 ~ +85 ‐ O X
X
X
‐50 ~ +90 ‐ ‐ X
X
X
‐55 ~ +95 ‐ ‐ ‐
X
X
Table 3: “Availability” X = available, O = available on request, ‐ not available 15, 20 X
X
X
X
Available Phase noise level (on request) Offset 10 MHz @ 10 Hz <‐95 dBc/Hz
@ 100 Hz <‐120 dBc/Hz
@ 1 kHz <‐140 dBc/Hz
@ 10 kHz <‐145 dBc/Hz
@ 100 kHz <‐150 dBc/Hz
Table 4: Phase noise 12.8 ~ 20 MHz
<‐135 dBc/Hz
20.48~38.4 MHz
40 MHz
<‐130 dBc/Hz
<‐125 dBc/Hz
Ordering Code Option 2 Option 3
Option 4
[Supply [RF [Stability] Voltage] output] AXLE7050B _ or “V” 33 or 50 C or H
Table 1
Example: AXLE7050B‐V‐5‐C‐05‐4F_Rev.1 – 10.000 MHz Model Option 1 [EFC]* GmbH & Co. KG
Roemerring 9 D‐74821 Mosbach Germany AXLE7050B Rev.1 Drawing D1 Page 2(4) Option 5
[Temperature Revision Frequency [MHz] range] Table 2
Rev.1 10.000 ww.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E‐mail: [email protected] Handling and Testing Parameter Procedure
Handling and Testing Processing Parameter Electrostatic discharge (ESD) THD devices SMD devices Washable RoHS compliant Source Application Note AXAN‐011
Application Note AXAN‐012
www.axtal.com www.axtal.com Procedure
Condition IEC60749‐26
HBM
IEC60749‐27
MM
 Yes  No
 Yes  No
2000 V 200 V Enclosure drawing Soldering pattern: Pin connections Pin #
1
2
3
4
*
Symbol
I.C. or
VC
GND
RF OUT
VS
I.C.
Function Do not connect or Control Voltage (EFC) Ground RF Output Supply Voltage Do not connect GmbH & Co. KG
Roemerring 9 D‐74821 Mosbach Germany AXLE7050B Rev.1 Drawing D1 Page 3(4) ww.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E‐mail: [email protected] Environmental conditions Test Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60068 Part … 2‐17 IEC 60679‐1 Clause 5.6.2 MIL‐STD‐ 202G Method 112E MIL‐STD‐ 810F Method MIL‐PRF‐ 55310D Clause 3.6.1.2 2‐20 2‐58 5.6.3 208H 210F 3.6.52 3.6.48 2‐27 5.6.8 213B 516.4 3.6.40 Test conditions (IEC) Gross leak: Test Qc, Fine leak: Test Qk Test Ta Method 1 Test Td1 Method 2 Test Td2 Method 2 Test Ea, 3 x per axes 100g, 6 ms half‐sine pulse Test Fc, 30 min per axes, 10 Hz ‐ 55 Hz 0,75mm; 55 Hz ‐ 2 kHz, 10g Test Fdb Vibration, 2‐6 5.6.7.1 201A 516.4‐4 3.6.38.1 sinusoidal* 204D 3.6.38.2 Vibration, 2‐64 5.6.7.3 214A 514.5 3.6.38.3 random* 3.6.38.4 Endurance tests 108A ‐ ageing 5.7.1 4.8.35 30 days @ 85°C, OCXO @25°C ‐ extended aging 5.7.2 1000h, 2000h, 8000h @85°C Other environmental conditions on request Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. Revision History Rev. Drawing Date [dd.mm.yyyy] 1 D1 20.01.2016 Remarks First issue AXLE7050B Author Checked BN BN GmbH & Co. KG
Roemerring 9 D‐74821 Mosbach Germany AXLE7050B Rev.1 Drawing D1 Page 4(4) ww.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E‐mail: [email protected]