Clamping force measurement with strain sensors Reliable, permanent force measurement Clamping force measurement with strain sensors. Monitoring, control, calibration. Highlights Your benefits Monitoring and control ■ Quick and easy installation ■ Accuracy 1% FS (full scale) Monitoring and control ■ Continuous monitoring ■ Verification of the clamping force ■ Recording of all measured values via PC or machine control system Calibration ■ Reliable and precise ■ Evaluation of the measured results via USB with InspectMaster software ■ Independent of diameter Calibration ■ Easy monitoring of clamping force, parallelism and bending ■ Installation/measurement/evaluation in a short time ■ Recording and evaluation of the measured values via PC Monitoring of clamping force – a crucial factor for compliance with end product quality Perfectly adjusted machines and tools, e.g. in presses and injection molding machines, are essential to fulfill the high requirements on the end product quality. This can be achieved through constant machine monitoring or periodic machine calibration with Baumer tie bar sensors. Regardless whether the measurements are made on or in the tie bar, the forces during each work cycle are continually recorded. Constant clamping force monitoring DSRC strain rings Easy installation, high measuring accuracy. These benefits make the strain ring a versatile measuring instrument for monitoring tasks. DSRH strain probes The right solution in tight spaces. Insert the strain probe in the hole, apply tension, connect and the measurement can start. DABU AD2T amplifiers The ideal amplifier for strain measurements. With its extremely low noise and first-class signal processing, the DABU AD2T is the ideal supplement in the measuring chain with strain sensors. Machine protection Calibration of machines clamping force / parallelism / bar bending Calibration with strain clamps and extensometers DSRV strain clamps and DSRM extensometers can be quickly and easily installed. The measured results are avail- able quickly. With the extensometer measurements are not only possible on tie bars but also on plane surfaces. The convincing measuring chain! The display box is the result of consistent development of the processing electronic range from Baumer. Together with the matching strain sensors, an ideal measuring chain is formed. Technical properties Technical properties measuring range ± 1000 με characteristic curve deviation < 1% FS 2 x ¼ DMS bridge DSRH strain probes measuring range ± 1000 με characteristic curve deviation < 1% FS for cyclic applications Ordering designations Type AX = axial cable outlet BT = radial cable outlet ST = plug outlet QM = quick mount latch Beam diameter (from 020…360 mm) e.g. 060 = 60 mm e.g. 150 = 150 mm Metric/imperial M = metric Z = imperial DSRC xx xxx x DSRH x xx-xxxx x Output U = voltage output ±10 V I = current output 4 - 20 mA P = passive version with cable outlet Bore diameter 12 = 12 mm 16 = 16 mm 20 = 20 mm Length 0200 to 1400 mm Metric/imperial M = metric Z = imperial DSRV strain clamps measuring range ± 1000 με characteristic curve deviation < 1% FS patented adjusting mechanism variably adjustable 2 x ¼ DMS bridge DDBF display box + InspectMaster analysis software incl. in the set DSRM extensometers DSRM M2M Measuring system with 2 sensors measuring range ± 1000 με DSRM M4M Measuring system with 4 sensors characteristic curve deviation < 2% FS DSRM M8M Measuring system with 8 sensors magnetic holder independent of diameter full bridge DDBF display box + InspectMaster analysis software incl. in the set DDBF display boxes freely configurable including InspectMaster evaluation software (multilingual) USB interface DABx AD2T bridge amplifiers voltage or current output very good noise characteristics 2 x ¼ bridge and full bridge Sensors/measuring ranges 30-100 DSRV SET-SOL 170 1 DSRV SET-LEG 240 1 DSRV SET-MED 170 4 DSRV SET-MED 240 0 DSRV SET-COM 240 4 DSRV SET-RNG 100 4 DSRV SET-RNG 170 0 DSRV SET-RNG 240 0 100-170 1 1 4 4 4 0 4 0 170-240 0 1 0 4 4 0 0 4 DDBF 2-SC 2-channel, 2 x ¼ bridge DDBF 4-SC 4-channel, 2 x ¼ bridge DDBF 4-SM 4-channel, full bridge DABx AD2T-xx xxxx Output U = voltage output I = current output DMS bridge FB = full bridge 2Q = 2 x ¼ bridge Gain 0,25 = 0,25 mV/V (Type FB) 0,50 = 0,50 mV/V (Type FB) 1,00 = 1,00 mV/V (Type FB) 2,00 = 2,00 mV/V (Type FB) 0250 = 250 με (Type 2Q) 0350 = 350 με (Type 2Q) 0500 = 500 με (Type 2Q) 1000 = 1000 με (Type 2Q) Further details can be found at www.baumersensopress.com Baumer Switzerland Baumer United Kingdom Baumer USA Baumer Electric AG · P.O. Box Hummelstrasse 17 · CH-8501 Frauenfeld Phone +41 (0)52 728 1122 Fax +41 (0)52 728 1144 [email protected] www.baumerelectric.com Baumer Ltd. · 33/36 Shrivenham Hundred Business Park Watchfield · Swindon SN6 8TZ GB Phone +44 (0)870 161 3000 Fax +44 (0)870 161 3030 [email protected] www.baumergroup.com Baumer Ltd. · 122 Spring Street, Unit C-6 US-Southington, CT 06489 Phone +1 (1)860 621-2121 Fax +1 (1)860 628-6280 [email protected] www.baumerelectric.com Technical modifications and errors reserved. Printed in Switzerland by Sonderegger Druck AG. 11/07 Nr. 802343 Product DSRC strain rings