® RT7285B 1.5A, 18V, 500kHz ACOTTM Synchronous Step-Down Converter General Description Features The RT7285B is a synchronous step-down converter with Advanced Constant On-Time (ACOTTM) mode control. The 4.3V to 18V Input Voltage Range 1.5A Output Current Advanced Constant On-Time Control Fast Transient Response Support All Ceramic Capacitors Up to 95% Efficiency 500kHz Switching Frequency Adjustable Output Voltage from 0.6V to 8V Cycle-by-Cycle Current Limit Input Under-Voltage Lockout Thermal Shutdown Power Saving Mode for High Efficiency at Light Load TM ACOT provides a very fast transient response with few external components. The low impedance internal MOSFET supports high efficiency operation with wide input voltage range from 4.3V to 18V. The proprietary circuit of the RT7285B enables to support all ceramic capacitors. The output voltage can be adjusted between 0.6V and 8V. Ordering Information RT7285B Package Type J6 : TSOT-23-6 Lead Plating System G : Green (Halogen Free and Pb Free) Applications Note : Richtek products are : RoHS compliant and compatible with the current require- ments of IPC/JEDEC J-STD-020. Suitable for use in SnPb or Pb-free soldering processes. Industrial and Commercial Low Power Systems Computer Peripherals LCD Monitors and TVs Green Electronics/Appliances Point of Load Regulation for High-Performance DSPs, FPGAs, and ASICs Pin Configurations (TOP VIEW) Marking Information SW VIN EN 6 5 4 2 3 0C= : Product Code 0C=DNN DNN : Date Code BOOT GND FB TSOT-23-6 Simplified Application Circuit VIN VIN RT7285B BOOT SW Enable VOUT FB EN GND Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS7285B-02 October 2014 is a registered trademark of Richtek Technology Corporation. www.richtek.com 1 RT7285B Functional Pin Description Pin No. Pin Name Pin Function Bootstrap Supply for High-Side Gate Driver. Connect a 0.1F ceramic capacitor between the BOOT and SW pins. 1 BOOT 2 GND Power Ground. 3 FB Feedback Voltage Input. The pin is used to set the output voltage of the converter via a resistive divider. The converter regulates VFB to 0.6V 4 EN Enable Control Input. Connect EN to a logic-high voltage to enable the IC or to a logic-low voltage to disable. Do not leave this high impedance input unconnected. 5 VIN Power Input. The input voltage range is from 4.3V to 18V. Must bypass with a suitable large ceramic capacitor at this pin. 6 SW Switch Node. Connect to external L-C filter. Function Block Diagram BOOT VIN VIN Reg PVCC VIBIAS VREF Min off PVCC UGATE OC Control SW Driver LGATE UV & OV GND PVCC SW Ripple Gen. + Comparator FB GND SW VIN EN On-Time SW EN Operation The RT7285B is a synchronous step-down converter with advanced constant on-time control mode. Using the ACOT control mode can reduce the output capacitance and fast transient response. It can minimize the component size without additional external compensation network. UVLO Protection Current Protection Thermal Shutdown The inductor current is monitored via the internal switches cycle-by-cycle. When the junction temperature exceeds the OTP threshold value, the IC will shut down the switching operation. Once the junction temperature cools down and is lower than the OTP lower threshold, the converter will autocratically resume switching. Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 2 To protect the chip from operating at insufficient supply voltage, the UVLO is needed. When the input voltage of VIN is lower than the UVLO falling threshold voltage, the device will be lockout. is a registered trademark of Richtek Technology Corporation. DS7285B-02 October 2014 RT7285B Absolute Maximum Ratings (Note 1) VIN to GND ----------------------------------------------------------------------------------------------------SW to GND ---------------------------------------------------------------------------------------------------< 10ns ---------------------------------------------------------------------------------------------------------BOOT to GND ------------------------------------------------------------------------------------------------Other Pins -----------------------------------------------------------------------------------------------------Power Dissipation, PD @ TA = 25°C TSOT-23-6 ------------------------------------------------------------------------------------------------------ 0.625W Package Thermal Resistance (Note 2) TSOT-23-6, θJA ------------------------------------------------------------------------------------------------ 160°C/W TSOT-23-6, θJC ------------------------------------------------------------------------------------------------ 15°C/W Lead Temperature (Soldering, 10 sec.) ------------------------------------------------------------------ 260°C Junction Temperature ---------------------------------------------------------------------------------------- 150°C Storage Temperature Range ------------------------------------------------------------------------------- −65°C to 150°C ESD Susceptibility (Note 3) HBM (Human Body Model) --------------------------------------------------------------------------------- 2kV Recommended Operating Conditions −0.3V to 20V −0.3V to (VIN + 0.3V) −5V to 25V (VSW − 0.3V) to (VSW + 6V) −0.3V to 6V (Note 4) Supply Input Voltage, VIN ---------------------------------------------------------------------------------- 4.3V to 18V Junction Temperature Range ------------------------------------------------------------------------------- −40°C to 125°C Ambient Temperature Range ------------------------------------------------------------------------------- −40°C to 85°C Electrical Characteristics (VIN = 12V, TA = 25°C, unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Unit Shutdown Current ISHDN VEN = 0V -- -- 4 A Quiescent Current IQ VEN = 2V, VFB = 1V -- 0.5 -- mA High-Side RDS(ON)_H VBOOTSW = 4.8V -- 230 -- Low-Side RDS(ON)_L VIN = 5V -- 130 -- Current Limit ILIM Vally current 1.7 2.2 2.8 A Oscillator Frequency f SW -- 500 -- kHz Maximum Duty Cycle DMAX -- 90 -- % Minimum On-Time tON -- 60 -- ns Feedback Threshold Voltage VFB 591 600 609 mV Logic-High VEN_H 1.5 -- -- Logic-Low VEN_L -- -- 0.4 3.55 3.9 4.25 V -- 340 -- mV Switch-On Resistance EN Input Threshold VIN Under-Voltage Lockout Threshold VUVLO VIN Under-Voltage Lockout Threshold Hysteresis Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS7285B-02 October 2014 VIN Rising m V is a registered trademark of Richtek Technology Corporation. www.richtek.com 3 RT7285B Parameter Symbol Test Conditions Min Typ Max Unit Soft-Start Time tSS -- 800 -- s Thermal Shutdown Threshold TSD -- 160 -- C Thermal Shutdown Hysteresis TSD -- 20 -- C VOUT Discharge Resistance RDISCHG -- 50 100 VEN = 0V, VOUT = 0.5V Note 1. Stresses beyond those listed “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Note 2. θJA is measured at TA = 25°C on a high effective thermal conductivity four-layer test board per JEDEC 51-7. The case position of θJC is on the top of the package. Note 3. Devices are ESD sensitive. Handling precaution is recommended. Note 4. The device is not guaranteed to function outside its operating conditions. Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 4 is a registered trademark of Richtek Technology Corporation. DS7285B-02 October 2014 RT7285B Typical Application Circuit RT7285B VIN 4.3V to 18V 5 CIN 10µF BOOT VIN CBOOT 100nF SW 6 4 EN Enable 1 L 2µH R1 10k FB 3 R2 10k GND 2 VOUT 1.2V COUT 22µF Table 1. Suggested Component Values VOUT (V) R1 (k) R2 (k) L (H) C OUT (F) C FF (pF) 5 110 15 10 22 29 3.3 115 25.5 6.8 22 33 2.5 25.5 8.06 4.7 22 NC 1.2 10 10 3.6 22 NC Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS7285B-02 October 2014 is a registered trademark of Richtek Technology Corporation. www.richtek.com 5 RT7285B Typical Operating Characteristics Reference Voltage vs. Input Voltage Efficiency vs. Load Current 100 0.610 90 0.608 Reference Voltage (V) Efficiency (%) 80 70 VIN = VIN = VIN = VIN = 60 50 40 5V 9V 12V 18V 30 20 0.605 0.603 0.600 0.598 0.595 0.593 10 VOUT = 1.2V 0 0.001 0.01 0.1 1 VIN = 4V to 18V, IOUT = 1A 0.590 4 10 5 6 7 8 Input Voltage (V) Load Current (A) Switching Frequency vs. Input Voltage Reference Voltage vs. Temperature 600 Switching Frequency (kHz)1 Reference Voltage (V) 0.610 0.605 VIN = 9V VIN = 12V VIN = 18V 0.600 0.595 VOUT = 1.2V, IOUT = 0.5A 590 580 570 560 550 540 530 520 510 VOUT = 1.2V, IOUT = 0.5A 500 0.590 -50 -25 0 25 50 75 100 4 125 5 6 7 8 Switching Frequency vs. Temperature Current Limit vs. Temperature 550 3.0 540 2.8 530 2.6 520 Current Limit (A) VIN = 6V VIN = 12V VIN = 18V 510 9 10 11 12 13 14 15 16 17 18 Input Voltage (V) Temperature (°C) Switching Frequency (kHz)1 9 10 11 12 13 14 15 16 17 18 500 490 480 470 2.4 VIN = 6V VIN = 12V VIN = 18V 2.2 2.0 1.8 1.6 1.4 460 VOUT = 1.2V, IOUT = 0.5A 450 -50 -25 0 25 50 75 100 Temperature (°C) Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 6 125 1.2 1.0 -50 -25 0 25 50 75 100 125 Temperature (°C) is a registered trademark of Richtek Technology Corporation. DS7285B-02 October 2014 RT7285B Load Transient Response Load Transient Response VOUT (20mV/Div) VOUT (20mV/Div) IOUT (1A/Div) IOUT (1A/Div) VIN = 12V, VOUT = 1.2V, IOUT = 0A to 1.5A Time (250μs/Div) Time (250μs/Div) Switching Power On from EN VOUT (10mV/Div) VEN (2V/Div) VOUT (1V/Div) VSW (5V/Div) IL (1A/Div) VSW (10V/Div) VIN = 12V, VOUT = 1.2V, IOUT = 1.5A I SW (1A/Div) VIN = 12V, VOUT = 1.2V, IOUT = 1.5A Time (1μs/Div) Time (2.5ms/Div) Power Off from EN Power On from VIN VEN (2V/Div) VIN (10V/Div) VOUT (1V/Div) VSW (10V/Div) VOUT (1V/Div) VSW (10V/Div) I SW (1A/Div) I SW (1A/Div) VIN = 12V, VOUT = 1.2V, IOUT = 1.5A VIN = 12V, VOUT = 1.2V, IOUT = 1.5A Time (5ms/Div) Time (2.5ms/Div) Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS7285B-02 VIN = 12V, VOUT = 1.2V, IOUT = 0.75A to 1.5A October 2014 is a registered trademark of Richtek Technology Corporation. www.richtek.com 7 RT7285B Power Off from VIN VIN (10V/Div) VOUT (1V/Div) VSW (10V/Div) I SW (1A/Div) VIN = 12V, VOUT = 1.2V, IOUT = 1.5A Time (2.5ms/Div) Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 8 is a registered trademark of Richtek Technology Corporation. DS7285B-02 October 2014 RT7285B Application information Inductor Selection Selecting an inductor involves specifying its inductance and also its required peak current. The exact inductor value is generally flexible and is ultimately chosen to obtain the best mix of cost, physical size, and circuit efficiency. Lower inductor values benefit from reduced size and cost and they can improve the circuit's transient response, but they increase the inductor ripple current and output voltage ripple and reduce the efficiency due to the resulting higher peak currents. Conversely, higher inductor values increase efficiency, but the inductor will either be physically larger or have higher resistance since more turns of wire are required and transient response will be slower since more time is required to change current (up or down) in the inductor. A good compromise between size, efficiency, and transient response is to use a ripple current (ΔIL) about 20% to 40% of the desired full output load current. Calculate the approximate inductor value by selecting the input and output voltages, the switching frequency (fSW), the maximum output current (IOUT(MAX)) and estimating a ΔIL as some percentage of that current. L= VOUT VIN VOUT VIN fSW IL Once an inductor value is chosen, the ripple current (ΔIL) is calculated to determine the required peak inductor current. VOUT VIN VOUT IL = VIN fSW L I IL(PEAK) = IOUT(MAX) L 2 IL IL(VALLY) = IOUT(MAX) 2 Considering the Typical Operating Circuit for 1.2V output at 1.5A and an input voltage of 12V, using an inductor ripple of 0.6A , the calculated inductance value is : L= 1.2 12 1.2 = 3.6μH 12 500kHz 0.6 The ripple current was selected at 0.6A and, as long as we use the calculated 3.6μH inductance, that should be the actual ripple current amount. The ripple current and required peak current as below : Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS7285B-02 October 2014 1.2 12 1.2 = 0.6A 12 500kHz 3.6μH and IL(PEAK) = 1.5A 0.6 = 1.8A 2 Inductor saturation current should be chosen over IC's current limit. IL = Input Capacitor Selection The input filter capacitors are needed to smooth out the switched current drawn from the input power source and to reduce voltage ripple on the input. The actual capacitance value is less important than the RMS current rating (and voltage rating, of course). The RMS input ripple current (IRMS) is a function of the input voltage, output voltage, and load current : V IRMS = IOUT(MAX) OUT VIN VIN 1 VOUT Ceramic capacitors are most often used because of their low cost, small size, high RMS current ratings, and robust surge current capabilities. However, take care when these capacitors are used at the input of circuits supplied by a wall adapter or other supply connected through long, thin wires. Current surges through the inductive wires can induce ringing at the RT7285B input which could potentially cause large, damaging voltage spikes at VIN. If this phenomenon is observed, some bulk input capacitance may be required. Ceramic capacitors (to meet the RMS current requirement) can be placed in parallel with other types such as tantalum, electrolytic, or polymer (to reduce ringing and overshoot). Choose capacitors rated at higher temperatures than required. Several ceramic capacitors may be paralleled to meet the RMS current, size, and height requirements of the application. The typical operating circuit use 10μF and one 0.1μF low ESR ceramic capacitors on the input. Output Capacitor Selection The RT7285B is optimized for ceramic output capacitors and best performance will be obtained using them. The total output capacitance value is usually determined by the desired output voltage ripple level and transient response requirements for sag (undershoot on positive load steps) and soar (overshoot on negative load steps). is a registered trademark of Richtek Technology Corporation. www.richtek.com 9 RT7285B Output Ripple Output ripple at the switching frequency is caused by the inductor current ripple and its effect on the output capacitor's ESR and stored charge. These two ripple components are called ESR ripple and capacitive ripple. Since ceramic capacitors have extremely low ESR and relatively little capacitance, both components are similar in amplitude and both should be considered if ripple is critical. VRIPPLE = VRIPPLE(ESR) VRIPPLE(C) VRIPPLE(ESR) = IL RESR VRIPPLE(C) = IL 8 COUT fSW For the Typical Operating Circuit for 1.2V output and an inductor ripple of 0.46A, with 1 x 22μF output capacitance each with about 5mΩ ESR including PCB trace resistance, the output voltage ripple components are : VRIPPLE(ESR) = 0.46A 5m = 2.3mV VRIPPLE(C) = 0.46A = 5.227mV 8 22μF 500kHz VRIPPLE = 2.3mV 5.227mV = 7.527mV Output Transient Undershoot and Overshoot In addition to voltage ripple at the switching frequency, the output capacitor and its ESR also affect the voltage sag (undershoot) and soar (overshoot) when the load steps up and down abruptly. The ACOT transient response is very quick and output transients are usually small. However, the combination of small ceramic output capacitors (with little capacitance), low output voltages (with little stored charge in the output capacitors), and low duty cycle applications (which require high inductance to get reasonable ripple currents with high input voltages) increases the size of voltage variations in response to very quick load changes. Typically, load changes occur slowly with respect to the IC's 500kHz switching frequency. But some modern digital loads can exhibit nearly instantaneous load changes and the following section shows how to calculate the worst-case voltage swings in response to very fast load steps. The output voltage transient undershoot and overshoot each have two components : the voltage steps caused by the Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 10 output capacitor's ESR, and the voltage sag and soar due to the finite output capacitance and the inductor current slew rate. Use the following formulas to check if the ESR is low enough (typically not a problem with ceramic capacitors) and the output capacitance is large enough to prevent excessive sag and soar on very fast load step edges, with the chosen inductor value. The amplitude of the ESR step up or down is a function of the load step and the ESR of the output capacitor : VESR _STEP = ΔIOUT x RESR The amplitude of the capacitive sag is a function of the load step, the output capacitor value, the inductor value, the input-to-output voltage differential, and the maximum duty cycle. The maximum duty cycle during a fast transient is a function of the on-time and the minimum off-time since the ACOTTM control scheme will ramp the current using on-times spaced apart with minimum off-times, which is as fast as allowed. Calculate the approximate on-time (neglecting parasitics) and maximum duty cycle for a given input and output voltage as : VOUT tON tON = and DMAX = VIN fSW tON tOFF(MIN) The actual on-time will be slightly longer as the IC compensates for voltage drops in the circuit, but we can neglect both of these since the on-time increase compensates for the voltage losses. Calculate the output voltage sag as : L (IOUT )2 VSAG = 2 COUT VIN(MIN) DMAX VOUT The amplitude of the capacitive soar is a function of the load step, the output capacitor value, the inductor value and the output voltage : VSOAR = L (IOUT )2 2 COUT VOUT Feed-forward Capacitor (Cff) The RT7285B is optimized for ceramic output capacitors and for low duty cycle applications. However for high-output voltages, with high feedback attenuation, the circuit's response becomes over-damped and transient response can be slowed. In high-output voltage circuits (VOUT > 3.3V) transient response is improved by adding a small “feedforward” capacitor (Cff) across the upper FB divider resistor is a registered trademark of Richtek Technology Corporation. DS7285B-02 October 2014 RT7285B (Figure 1), to increase the circuit's Q and reduce damping to speed up the transient response without affecting the steady-state stability of the circuit. Choose a suitable capacitor value that following below step. Get the BW the quickest method to do transient response form no load to full load. Confirm the damping frequency. The damping frequency is BW. VOUT Cff FB RT7285B For automatic start-up the EN pin can be connected to VIN, through a 100kΩ resistor. Its large hysteresis band makes EN useful for simple delay and timing circuits. EN can be externally pulled to VIN by adding a resistorcapacitor delay (REN and CEN in Figure 2). Calculate the delay time using EN's internal threshold where switching operation begins (1.4V, typical). An external MOSFET can be added to implement digital control of EN when no system voltage above 2V is available (Figure 3). In this case, a 100kΩ pull-up resistor, REN, is connected between VIN and the EN pin. MOSFET Q1 will be under logic control to pull down the EN pin. To prevent enabling circuit when VIN is smaller than the VOUT target value or some other desired voltage level, a resistive voltage divider can be placed between the input voltage and ground and connected to EN to create an additional input under voltage lockout threshold (Figure 4). BW R1 Enable Operation (EN) EN R2 GND VIN REN EN RT7285B CEN GND Figure 1. Cff Capacitor Setting Cff can be calculated base on below equation : Cff Figure 2. External Timing Control 1 2 3.1412 R1 BW 0.8 VIN Internal Soft-Start (SS) REN 100k Q1 Enable The RT7285B soft-start uses an internal soft-start time 800μs. Following below equation to get the minimum capacitance range in order to avoid UV occur. COUT VOUT 0.6 1.2 (ILIM Load Current) 0.8 T 800μs T EN RT7285B GND Figure 3. Digital Enable Control Circuit VIN REN1 REN2 EN RT7285B GND Figure 4. Resistor Divider for Lockout Threshold Setting Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS7285B-02 October 2014 is a registered trademark of Richtek Technology Corporation. www.richtek.com 11 RT7285B Output Voltage Setting Set the desired output voltage using a resistive divider from the output to ground with the midpoint connected to FB. The output voltage is set according to the following equation : VOUT = 0.6 x (1 + R1 / R2) VOUT resistance between BOOT and the external bootstrap capacitor. This will slow the high-side switch turn-on and VSW's rise. To remove the resistor from the capacitor charging path (avoiding poor enhancement due to undercharging the BOOT capacitor), use the external diode shown in figure 6 to charge the BOOT capacitor and place the resistance between BOOT and the capacitor/diode connection. 5V R1 FB RT7285B BOOT R2 GND 0.1µF RT7285B SW Figure 5. Output Voltage Setting Place the FB resistors within 5mm of the FB pin. Choose R2 between 10kΩ and 100kΩ to minimize power consumption without excessive noise pick-up and calculate R1 as follows : R1 R2 (VOUT 0.6) 0.6 For output voltage accuracy, use divider resistors with 1% or better tolerance. External BOOT Bootstrap Diode When the input voltage is lower than 5.5V it is recommended to add an external bootstrap diode between VIN (or VINR) and the BOOT pin to improve enhancement of the internal MOSFET switch and improve efficiency. The bootstrap diode can be a low cost one such as 1N4148 or BAT54. External BOOT Capacitor Series Resistance The internal power MOSFET switch gate driver is optimized to turn the switch on fast enough for low power loss and good efficiency, but also slow enough to reduce EMI. Switch turn-on is when most EMI occurs since VSW rises rapidly. During switch turn-off, SW is discharged relatively slowly by the inductor current during the deadtime between high-side and low-side switch on-times. In some cases it is desirable to reduce EMI further, at the expense of some additional power dissipation. The switch turn-on can be slowed by placing a small (<47Ω) Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 12 Figure 6. External Bootstrap Diode Over-Temperature Protection The RT7285B features an Over-Temperature Protection (OTP) circuitry to prevent from overheating due to excessive power dissipation. The OTP will shut down switching operation when junction temperature exceeds 160°C. Once the junction temperature cools down by approximately 20°C, the converter will resume operation. To maintain continuous operation, the maximum junction temperature should be lower than 125°C. Clamp Mode For the Clamp, it provides current limit protection, Under Voltage Protection (UVP) is disable, when the UV condition is removed, the converter will resume operation. Thermal Considerations For continuous operation, do not exceed absolute maximum junction temperature. The maximum power dissipation depends on the thermal resistance of the IC package, PCB layout, rate of surrounding airflow, and difference between junction and ambient temperature. The maximum power dissipation can be calculated by the following formula : PD(MAX) = (TJ(MAX) − TA) / θJA where TJ(MAX) is the maximum junction temperature, TA is the ambient temperature, and θJA is the junction to ambient thermal resistance. is a registered trademark of Richtek Technology Corporation. DS7285B-02 October 2014 RT7285B For recommended operating condition specifications, the maximum junction temperature is 125°C. The junction to ambient thermal resistance, θJA, is layout dependent. For TSOT-23-6 package, the thermal resistance, θJA, is 160°C/ W on a standard four-layer thermal test board. The maximum power dissipation at TA = 25°C can be calculated by the following formula : PD(MAX) = (125°C − 25°C) / (160°C/W) = 0.625W for TSOT-23-6 package Layout Considerations For best performance of the RT7285B, the following layout guidelines must be strictly followed. Input capacitor must be placed as close to the IC as possible. SW should be connected to inductor by wide and short trace. Keep sensitive components away from this trace. The maximum power dissipation depends on the operating ambient temperature for fixed T J(MAX) and thermal resistance, θJA. The derating curve in Figure 7 allows the designer to see the effect of rising ambient temperature on the maximum power dissipation. Maximum Power Dissipation (W)1 2.0 Four-Layer PCB 1.6 1.2 0.8 0.4 0.0 0 25 50 75 100 125 Ambient Temperature (°C) Figure 7. Derating Curve of Maximum Power Dissipation Copyright © 2014 Richtek Technology Corporation. All rights reserved. DS7285B-02 October 2014 is a registered trademark of Richtek Technology Corporation. www.richtek.com 13 RT7285B SW should be connected to inductor by Wide and short trace. Keep sensitive components away from this trace. Suggestion layout trace wider for thermal . Keep sensitive components away from this trace. Suggestion layout trace wider for thermal. COUT SW Suggestion layout trace wider for thermal. COUT VOUT CS* BOOT VOUT R1 6 SW GND 2 5 VIN FB 3 4 EN GND RS* CIN REN CIN VIN R2 The REN component must The feedback components must be connected as close to the device as possible. Input capacitor must be placed As close to the IC as possible. Suggestion layout trace wider for thermal. be connected to VIN. Suggestion layout trace wider for thermal. Figure 8. PCB Layout Guide Copyright © 2014 Richtek Technology Corporation. All rights reserved. www.richtek.com 14 is a registered trademark of Richtek Technology Corporation. DS7285B-02 October 2014 RT7285B Outline Dimension H D L C B b A A1 e Symbol Dimensions In Millimeters Dimensions In Inches Min Max Min Max A 0.700 1.000 0.028 0.039 A1 0.000 0.100 0.000 0.004 B 1.397 1.803 0.055 0.071 b 0.300 0.559 0.012 0.022 C 2.591 3.000 0.102 0.118 D 2.692 3.099 0.106 0.122 e 0.838 1.041 0.033 0.041 H 0.080 0.254 0.003 0.010 L 0.300 0.610 0.012 0.024 TSOT-23-6 Surface Mount Package Richtek Technology Corporation 14F, No. 8, Tai Yuen 1st Street, Chupei City Hsinchu, Taiwan, R.O.C. Tel: (8863)5526789 Richtek products are sold by description only. Richtek reserves the right to change the circuitry and/or specifications without notice at any time. Customers should obtain the latest relevant information and data sheets before placing orders and should verify that such information is current and complete. Richtek cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Richtek product. Information furnished by Richtek is believed to be accurate and reliable. However, no responsibility is assumed by Richtek or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Richtek or its subsidiaries. DS7285B-02 October 2014 www.richtek.com 15