PPM40-H

PPM40-H-xxELF
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
PPM-SERIES
Rev.03-2013
40 Watt
Univ. 85-264VAC (120-370VDC)
Single Output
Over Voltage Protection (out)
3 kV AC I/O Isolation
Low Ripple and Noise
High Efficiency
The PPM-Series are high efficiency green power moduls with various
packaging provided by Peak. The features of this series are: wide input
voltage, DC and AC all in one, high efficiency, high reliability, low loss, safety
isolation etc. They are widely used in industrial, office and civil equipments.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Input Voltage Range
Input Frequency
Input Current
Inrush Current
85 – 264 VAC or 120 – 370 VDC universal
47 – 440 Hz
115 VAC at 0.86A, max ; 230 VAC at 0.46A, max
115 VAC at 30A, max ; 230 VAC at 50A, max
Output Specifications
Voltage Accuracy
Line Regulation (full load)
Load Regulation (10-100%)
Ripple and Noise (20Mhz bandwidth)
Short Circuit Protection
Over Current Protection
Over Voltage Protection
Min Load
Trim
±2%
±0.5%
±1%
3.3, 5 Vout - 50mV pk-pk, typ
12, 24 Vout - 100mV pk-pk, typ
Continuous, auto resume
110-150% , auto resume
Zener Diode Clamp
1%
10%
Common Specifications
Temperature range
Storage
Hold up Time
Humidity
Altitude
Switching Frequency
I/O Isolation Voltage
Safety Standards
Safety Approvals
Safety Class
Hot swap
Case Material
Install
Cooling
Reliability Calculated MTBF (MIL-HDBK-217F)
Weight
-40°C to +70 °C
-40°C to +85 °C
15mS, typ. at 115VAC
80mS, typ at 230VAC
95%, max.
2000m, max
65kHz, typ
3000VAC / 1min.
IEC60950, EN60950, UL60950
pending
CLASS II
Forbid
UL94V-0 rated
PCB
Free air convection
> 200,000 hrs
~ 250g
PPM-Series – PPM40-H-xxELF – Single Output - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/4
Selection Guide
Single Output
Order #
Pow
er
(W )
O u tp
u
lta g
t Vo
e (V
d c)
O ut p
u
r re
t Cu
nt F
u
ad
ll L o
E ffic
ie n
( mA
)
)
cy ( %
Ca p
a
Lo
c it o r
ad (
uF)
S ta n
d
ow
by P
e r, m
ax
SINGLE OUTPUT
PPM26-H-3R3ELF
PPM40-H-05ELF
PPM40-H-12ELF
PPM40-H-24ELF
26.4
40
40
40
3.3
05
12
24
8000
8000
3333
1667
78
82
84
84
60000
40000
9000
2000
0.5W
0.5W
0.5W
0.5W
If you need other specifications, please enquire.
Package / Pinning / Derating
7
25.00
[0.984]
2
Ф1.20[0.047]
4
1
3
All dimensions are typical in millimeters (inches).
- Pin diameter: 1.0 +/-0.10 (0.04 +/-0.004)
- Pin pitch tolerance: +/-0.35 (+/-0.014)
- Case tolerance +/-0.5 (+/-0.02)
- Specification may change without notice
81.28[3.200]
89.00[3.504]
#
1
2
3
4
5
6
7
6.00
[0.236]
5
55.88[2.200]
(Bottom View)
25.40
[1.000]
6
55.88[2.200]
63.50[2.500]
(Front View)
PIN CONNECTIONS
SINGLE
AC (L)
AC (N)
+ Vo
No Pin
- Vo
No Pin
Trim
Temperature Derating Graph
Ambient Temperature ° C
Output
24V Output
100%
12V Output
70
3.3, 5V
Output
60
45
25
-40 -30
0
45 55 70 100
PPM-Series – PPM40-H-xxELF – Single Output - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/4
App Notes:
Trim Application & Trim Calculation
Application circuit for TRIM
(Part in broken line is the interior of models)
Formula for resistance of Trim
+Vot
+Vot
R1
V ref
Trim
V ref
R2
RT
R1
R3
R3
Trim
up: R T =
aR 2
R 2 -a
-R 3
a=
Vref
R1
Vot-Vref
down: R T =
aR 1
R 1 -a
-R 3
a=
Vot-Vref
R2
Vref
Note: Value for R1, R2, R3, and Vref refer to the following table.
RT: Resistance of Trim
a: User-defined parameter, no actual meanings.
RT
Vo(V)
R2
3.3
0V
0V
Trim up
Trim down
Resistance
R1(KΩ)
R2(KΩ)
R3(KΩ)
Vref(V)
Vot(V)
5V
12V
24V
2
3.3
3.83
8.66
1.2
3.3
1
1
1
1
1
1
1.24
2.5
2.5
2.5
Output voltage of Trim, variation ≤ ±10%
EMC
EMI
EMS
EN55022, Class B
ESD IEC/EN 61000-4-2 ±6kV/8kV
perf. Criteria B
RS IEC/EN 61000-4-3 10V/m
perf. Criteria A
EFT IEC/EN 61000-4-4 ±2kV (without external circuit)
perf. Criteria B
IEC/EN 61000-4-4 ±4kV (with typical application, fig 3)
Surge IEC/EN 61000-4-5 ±1kV/±2kV (without external circuit) perf. Criteria B
IEC/EN 61000-4-5 ±2kV/±4kV (with typical application, fig 3)
CS IEC/EN 61000-4-6 10 Vr.m.s.
perf. Criteria A
PFM IEC/EN 61000-4-8 10A/m
perf. Criteria A
Voltage dips, short and interruption immunity IEC/EN 61000-4-11 95% 5000ms
perf. Criteria B
Parallel Lines Measure
C o p p e r sh e e t
FU SE
L
L
+Vo
C1
AC-DC
N
N
C2
Load
C o n n e ct
Oscillo g ra p h Pro b e
-Vo
1 2 . 7 mm
2 5 . 4 mm
2 5 . 4 mm
Note: C1: 1µF (Ceramic capacitor) C2: 10µF (Electrolytic capacitor)
PPM-Series – PPM40-H-xxELF – Single Output - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/4
App Notes:
Typical Applications PPM-Series
Fig 2
Fig 1
FUSE
C1
L
L
C2 TVS
L
L
+Vo
+
+Vo
+Vo
AC-DC
RL
N
N
-Vo
-Vo
PE
N
N
-Vo
Note: This application is not supported for this series.
FUSE
N TC
MO V2
L
L
C Y1
R1
MO V1
CX
LCM
ACDC
C Y2
O UTPU T
MO V3
N
N
External Typical Value
Model
C1(µF)
C2(µF)
TVS
680
SMBJ7.0A
680
SMBJ7.0A
PPM40-H-12ELF
220
SMBJ20A
PPM40-H-24ELF
120
SMBJ30A
PPM26-H-3R3ELF
PPM40-H-05ELF
1
Note:
1. C1 is a ceramic capacitor, it is used to filter high frequency noise. Output filtering capacitors C2 is a electrolytic capacitor, It is
recommended to use high frequency and low impedance electrolytic capacitors. For capacitance and current of capacitors please refer
to manufacture’s datasheet. Voltage derating of capacitor should be 80% or above. TVS is a recommended component to protect
post-circuits (if converter fails).
2. For standard EMC requirement, please refer to figure 1 or figure 2 if higher EMC requirement, please refer to figure 3
Figure 3 MOV1 561KD14
MOV2 MOV3 561KD07
CX 0.15µF/300VAC;
CY1 CY2 222M/400VAC
R1 1MΩ/2W
LCM 2mH-10mH
NTC 5D-9
FUSE： Recommended to use3.15A/250V
PPM-Series – PPM40-H-xxELF – Single Output - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 4/4