PPMxx-SIP-xxELF

PPMxx-SIP-xxELF
PPM-SIP-SERIES
Rev.09-2013
1.65 - 3 Watt
Univ. 100-400VDC / 85-264VAC*
Single Output
Over Temperature Protection
Short Circuit Protection
2 kV AC I/O Isolation
High Efficiency / Density
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
The PPM-SIP-Series are high efficiency green power modules with
miniature packaging provided by Peak. The features of this series are: wide
input voltage, DC and AC all in one, high efficiency, high reliability, low loss,
safety isolation etc. They are widely used in industrial, office and civil
equipments, as well as applications where no special requirement for EMC
performance. It is recommended to add EMI suppression circuit or take
measure to shield when there is strict requirement for EMC performance.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Input Voltage Range
Input Current
External Input Fuse (recommended)
100 – 400 VDC or 85 – 264 VAC* universal
40mA, typ.
1A / 250V
* Attention: For AC-Input a capacitor between PIN 7 and PIN 10 is needed!! (See page 3)
Output Specifications
Voltage Accuracy
Input variation
Load variation (10-100%)
Ripple and Noise (20Mhz bandwidth)
3.3 / 5 / 9 VDC models
12 VDC models
15 VDC models
24VDC models
±2%
±0.5%, typ.
±1%, typ.
≤ 100mV pk-pk (50mV pk-pk typ.)
≤ 120mV pk-pk (60mV pk-pk typ.)
≤ 150mV pk-pk (75mV pk-pk typ.)
≤ 240mV pk-pk (120mV pk-pk typ.)
Short Circuit Protection
Over Temperature Protection
Continuous, auto recovery
150°C, max.
Common Specifications
Temperature range
Power derating
Case temperature
Storage
Humidity (non condensing)
Temperature Coefficient
Switching Frequency
I/O Isolation Voltage
Leakage current
Case Material
Reliability Calculated MTBF (MIL-HDBK-217F)
-40°C to +85 °C
1.33% / °C (above 55°C)
+90°C, max.
-40°C to +105 °C
85%, max.
0.02%/°C
100kHz, typ.
2000VAC / 1min.
None
UL94V-0 rated
> 300,000 hrs
PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/3
Selection Guide
mA)
ad (
o
)
L
c
l
l
d
t Fu
e (V
%)
rren
ltag
)
u
o
W
V
C
cy (
(
n
t
t
r
e
u
u
i
e
p
p
Pow
Out
O ut
Effic
Order #
SINGLE OUTPUT
PPM1.65-SIP-3R3ELF
1.65
3.3
PPM2.5-SIP-05ELF
2.5
5
PPM3-SIP-09ELF
3
9
PPM3-SIP-12ELF
3
12
PPM3-SIP-15ELF
3
15
PPM3-SIP-24ELF
3
24
If you need other specifications, please enquire.
500
500
330
250
200
125
70
70
75
78
78
78
Package / Pinning / Derating
10.50
(0.413)
max.
Printed
Face
Backside
1
3
7
10
6.00
(0.236)
max. 25.50
(1.004)
max. 35.00
(1.38)
12
0.40
(0.016)
0.84
(0.033)
22.86
(0.90)
12.70
(0.50)
5.08
(0.20)
All dimensions are typical in millimeters (inches).
- Pin section tolerance: +/-0.10 (+/-0.004)
- Case tolerance +/-0.5 (+/-0.02)
Specification may change without notice.
Ø 1.30 (0.051)
SIP – AC/DC
Load(%)
100
PIN CONNECTIONS
#
SINGLE
1
+Vout
3
- Vout
7
- Vin
10
CAP
12
+Vin
80
60
40
-40 -20
Temperature( C )
PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/3
55
85
App Notes:
Structure Figure
Anear Measure
12
+Vin( L)
1
DC/DC
Convertor
Rectificate
7
-Vin(N)
Rectifier
filter
circuit
-Vo
Load
Voltage
sampling
+
10
Contrl
Circuit
Connect Oscillograph Probe
Copper sheet
FUSE
L
3
C1
External
Capacitor
+Vo
Feedback
loop
N
Note:
C1: 1µF (Ceramic capacitor)
C2: 10µF (Electrolytic capacitor)
Typical Application
FUSE
12
M OV
N
+Vo C2 C3 T VS RL
1
NTC
L
C1
+
L
L
+Vo
+Vo
+
10
AC-DC
3
-Vo
7
N
N
-Vo
-Vo
CY
Fig. 1: Standard
Fig. 2: This application is not supported for this Series.
can u se MOR N S U N ’s F C -L0 1D
FUSE
R2
LDM
L
L
CY1
CY3
MOV
L CM CX
CY2
R3
CY4
C1
+
10
ACDC
OUTPUT
R1
N
N
PE
CY
Fig. 3: PPM-SIP-Series Recommended circuit for application require higher EMC standard
(external circuit output same as above)
Attention: For AC-Input a capacitor (10uF/400V) between PIN 7 and PIN 10 is needed!!
External Capacitor Typical Value
Output Voltage
3.3V
5V
9V
12V
15V
24V
C1
C2
C3
TVS
FUSE
SMBJ7.0A
150µF/25V
10µF/400V
1µF/50V
1A/250V
SMBJ12A
SMBJ20A
100µF/35V
SMBJ30A
Note:
1.
C1: AC input, is a filtering electrolytic capacitor, which is required when input voltage is below 100VAC, and the value of C1 is
22µF/400V. DC input, is a filtering capacitor in EMC Filter, the value of C1 is 10µF/400V (when input voltage is above 370VDC,
and the value of C1 is 10µF/450V), If EMC performance is not required, C1 could not need.
2.
C2 is ceramic capacitor, it is used to filter high frequency noise. Output filtering capacitor C3 (which is required by AC input or DC
input) is recommended to use high frequency and low impedance electrolytic capacitors. Voltage derating of capacitor should be
80% or above. TVS is a recommended component to protect post-circuits (if converter fails).
3.
Recommended external circuit parameters in Figure 3:
MOV: Varistor, model: 561KD14 it is used to protect the device under surge;
R1 R2 2Ω/3W Winding resistor R3 1MΩ/2W
CY CY1 CY2 CY3 CY4 102M/400VAC CX 0.22µF/275VAC
LCM 10mH-30mH LDM 300µH
4.
FUSE 1A/250V Slow-Blow
PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/3